1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Driver for Goodix Touchscreens 4 * 5 * Copyright (c) 2014 Red Hat Inc. 6 * Copyright (c) 2015 K. Merker <merker@debian.org> 7 * 8 * This code is based on gt9xx.c authored by andrew@goodix.com: 9 * 10 * 2010 - 2012 Goodix Technology. 11 */ 12 13 14 #include <linux/kernel.h> 15 #include <linux/dmi.h> 16 #include <linux/firmware.h> 17 #include <linux/module.h> 18 #include <linux/delay.h> 19 #include <linux/irq.h> 20 #include <linux/interrupt.h> 21 #include <linux/slab.h> 22 #include <linux/acpi.h> 23 #include <linux/of.h> 24 #include <asm/unaligned.h> 25 #include "goodix.h" 26 27 #define GOODIX_GPIO_INT_NAME "irq" 28 #define GOODIX_GPIO_RST_NAME "reset" 29 30 #define GOODIX_MAX_HEIGHT 4096 31 #define GOODIX_MAX_WIDTH 4096 32 #define GOODIX_INT_TRIGGER 1 33 #define GOODIX_CONTACT_SIZE 8 34 #define GOODIX_MAX_CONTACT_SIZE 9 35 #define GOODIX_MAX_CONTACTS 10 36 37 #define GOODIX_CONFIG_MIN_LENGTH 186 38 #define GOODIX_CONFIG_911_LENGTH 186 39 #define GOODIX_CONFIG_967_LENGTH 228 40 #define GOODIX_CONFIG_GT9X_LENGTH 240 41 42 #define GOODIX_BUFFER_STATUS_READY BIT(7) 43 #define GOODIX_HAVE_KEY BIT(4) 44 #define GOODIX_BUFFER_STATUS_TIMEOUT 20 45 46 #define RESOLUTION_LOC 1 47 #define MAX_CONTACTS_LOC 5 48 #define TRIGGER_LOC 6 49 50 /* Our special handling for GPIO accesses through ACPI is x86 specific */ 51 #if defined CONFIG_X86 && defined CONFIG_ACPI 52 #define ACPI_GPIO_SUPPORT 53 #endif 54 55 struct goodix_chip_id { 56 const char *id; 57 const struct goodix_chip_data *data; 58 }; 59 60 static int goodix_check_cfg_8(struct goodix_ts_data *ts, 61 const u8 *cfg, int len); 62 static int goodix_check_cfg_16(struct goodix_ts_data *ts, 63 const u8 *cfg, int len); 64 static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts); 65 static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts); 66 67 static const struct goodix_chip_data gt1x_chip_data = { 68 .config_addr = GOODIX_GT1X_REG_CONFIG_DATA, 69 .config_len = GOODIX_CONFIG_GT9X_LENGTH, 70 .check_config = goodix_check_cfg_16, 71 .calc_config_checksum = goodix_calc_cfg_checksum_16, 72 }; 73 74 static const struct goodix_chip_data gt911_chip_data = { 75 .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, 76 .config_len = GOODIX_CONFIG_911_LENGTH, 77 .check_config = goodix_check_cfg_8, 78 .calc_config_checksum = goodix_calc_cfg_checksum_8, 79 }; 80 81 static const struct goodix_chip_data gt967_chip_data = { 82 .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, 83 .config_len = GOODIX_CONFIG_967_LENGTH, 84 .check_config = goodix_check_cfg_8, 85 .calc_config_checksum = goodix_calc_cfg_checksum_8, 86 }; 87 88 static const struct goodix_chip_data gt9x_chip_data = { 89 .config_addr = GOODIX_GT9X_REG_CONFIG_DATA, 90 .config_len = GOODIX_CONFIG_GT9X_LENGTH, 91 .check_config = goodix_check_cfg_8, 92 .calc_config_checksum = goodix_calc_cfg_checksum_8, 93 }; 94 95 static const struct goodix_chip_id goodix_chip_ids[] = { 96 { .id = "1151", .data = >1x_chip_data }, 97 { .id = "5663", .data = >1x_chip_data }, 98 { .id = "5688", .data = >1x_chip_data }, 99 { .id = "917S", .data = >1x_chip_data }, 100 { .id = "9286", .data = >1x_chip_data }, 101 102 { .id = "911", .data = >911_chip_data }, 103 { .id = "9271", .data = >911_chip_data }, 104 { .id = "9110", .data = >911_chip_data }, 105 { .id = "9111", .data = >911_chip_data }, 106 { .id = "927", .data = >911_chip_data }, 107 { .id = "928", .data = >911_chip_data }, 108 109 { .id = "912", .data = >967_chip_data }, 110 { .id = "9147", .data = >967_chip_data }, 111 { .id = "967", .data = >967_chip_data }, 112 { } 113 }; 114 115 static const unsigned long goodix_irq_flags[] = { 116 IRQ_TYPE_EDGE_RISING, 117 IRQ_TYPE_EDGE_FALLING, 118 IRQ_TYPE_LEVEL_LOW, 119 IRQ_TYPE_LEVEL_HIGH, 120 }; 121 122 static const struct dmi_system_id nine_bytes_report[] = { 123 #if defined(CONFIG_DMI) && defined(CONFIG_X86) 124 { 125 .ident = "Lenovo YogaBook", 126 /* YB1-X91L/F and YB1-X90L/F */ 127 .matches = { 128 DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X9") 129 } 130 }, 131 #endif 132 {} 133 }; 134 135 /* 136 * Those tablets have their x coordinate inverted 137 */ 138 static const struct dmi_system_id inverted_x_screen[] = { 139 #if defined(CONFIG_DMI) && defined(CONFIG_X86) 140 { 141 .ident = "Cube I15-TC", 142 .matches = { 143 DMI_MATCH(DMI_SYS_VENDOR, "Cube"), 144 DMI_MATCH(DMI_PRODUCT_NAME, "I15-TC") 145 }, 146 }, 147 #endif 148 {} 149 }; 150 151 /** 152 * goodix_i2c_read - read data from a register of the i2c slave device. 153 * 154 * @client: i2c device. 155 * @reg: the register to read from. 156 * @buf: raw write data buffer. 157 * @len: length of the buffer to write 158 */ 159 int goodix_i2c_read(struct i2c_client *client, u16 reg, u8 *buf, int len) 160 { 161 struct i2c_msg msgs[2]; 162 __be16 wbuf = cpu_to_be16(reg); 163 int ret; 164 165 msgs[0].flags = 0; 166 msgs[0].addr = client->addr; 167 msgs[0].len = 2; 168 msgs[0].buf = (u8 *)&wbuf; 169 170 msgs[1].flags = I2C_M_RD; 171 msgs[1].addr = client->addr; 172 msgs[1].len = len; 173 msgs[1].buf = buf; 174 175 ret = i2c_transfer(client->adapter, msgs, 2); 176 if (ret >= 0) 177 ret = (ret == ARRAY_SIZE(msgs) ? 0 : -EIO); 178 179 if (ret) 180 dev_err(&client->dev, "Error reading %d bytes from 0x%04x: %d\n", 181 len, reg, ret); 182 return ret; 183 } 184 185 /** 186 * goodix_i2c_write - write data to a register of the i2c slave device. 187 * 188 * @client: i2c device. 189 * @reg: the register to write to. 190 * @buf: raw data buffer to write. 191 * @len: length of the buffer to write 192 */ 193 int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf, int len) 194 { 195 u8 *addr_buf; 196 struct i2c_msg msg; 197 int ret; 198 199 addr_buf = kmalloc(len + 2, GFP_KERNEL); 200 if (!addr_buf) 201 return -ENOMEM; 202 203 addr_buf[0] = reg >> 8; 204 addr_buf[1] = reg & 0xFF; 205 memcpy(&addr_buf[2], buf, len); 206 207 msg.flags = 0; 208 msg.addr = client->addr; 209 msg.buf = addr_buf; 210 msg.len = len + 2; 211 212 ret = i2c_transfer(client->adapter, &msg, 1); 213 if (ret >= 0) 214 ret = (ret == 1 ? 0 : -EIO); 215 216 kfree(addr_buf); 217 218 if (ret) 219 dev_err(&client->dev, "Error writing %d bytes to 0x%04x: %d\n", 220 len, reg, ret); 221 return ret; 222 } 223 224 int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value) 225 { 226 return goodix_i2c_write(client, reg, &value, sizeof(value)); 227 } 228 229 static const struct goodix_chip_data *goodix_get_chip_data(const char *id) 230 { 231 unsigned int i; 232 233 for (i = 0; goodix_chip_ids[i].id; i++) { 234 if (!strcmp(goodix_chip_ids[i].id, id)) 235 return goodix_chip_ids[i].data; 236 } 237 238 return >9x_chip_data; 239 } 240 241 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data) 242 { 243 unsigned long max_timeout; 244 int touch_num; 245 int error; 246 u16 addr = GOODIX_READ_COOR_ADDR; 247 /* 248 * We are going to read 1-byte header, 249 * ts->contact_size * max(1, touch_num) bytes of coordinates 250 * and 1-byte footer which contains the touch-key code. 251 */ 252 const int header_contact_keycode_size = 1 + ts->contact_size + 1; 253 254 /* 255 * The 'buffer status' bit, which indicates that the data is valid, is 256 * not set as soon as the interrupt is raised, but slightly after. 257 * This takes around 10 ms to happen, so we poll for 20 ms. 258 */ 259 max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT); 260 do { 261 error = goodix_i2c_read(ts->client, addr, data, 262 header_contact_keycode_size); 263 if (error) 264 return error; 265 266 if (data[0] & GOODIX_BUFFER_STATUS_READY) { 267 touch_num = data[0] & 0x0f; 268 if (touch_num > ts->max_touch_num) 269 return -EPROTO; 270 271 if (touch_num > 1) { 272 addr += header_contact_keycode_size; 273 data += header_contact_keycode_size; 274 error = goodix_i2c_read(ts->client, 275 addr, data, 276 ts->contact_size * 277 (touch_num - 1)); 278 if (error) 279 return error; 280 } 281 282 return touch_num; 283 } 284 285 if (data[0] == 0 && ts->firmware_name) { 286 if (goodix_handle_fw_request(ts)) 287 return 0; 288 } 289 290 usleep_range(1000, 2000); /* Poll every 1 - 2 ms */ 291 } while (time_before(jiffies, max_timeout)); 292 293 /* 294 * The Goodix panel will send spurious interrupts after a 295 * 'finger up' event, which will always cause a timeout. 296 */ 297 return -ENOMSG; 298 } 299 300 static struct input_dev *goodix_create_pen_input(struct goodix_ts_data *ts) 301 { 302 struct device *dev = &ts->client->dev; 303 struct input_dev *input; 304 305 input = devm_input_allocate_device(dev); 306 if (!input) 307 return NULL; 308 309 input_alloc_absinfo(input); 310 if (!input->absinfo) { 311 input_free_device(input); 312 return NULL; 313 } 314 315 input->absinfo[ABS_X] = ts->input_dev->absinfo[ABS_MT_POSITION_X]; 316 input->absinfo[ABS_Y] = ts->input_dev->absinfo[ABS_MT_POSITION_Y]; 317 __set_bit(ABS_X, input->absbit); 318 __set_bit(ABS_Y, input->absbit); 319 input_set_abs_params(input, ABS_PRESSURE, 0, 255, 0, 0); 320 321 input_set_capability(input, EV_KEY, BTN_TOUCH); 322 input_set_capability(input, EV_KEY, BTN_TOOL_PEN); 323 input_set_capability(input, EV_KEY, BTN_STYLUS); 324 input_set_capability(input, EV_KEY, BTN_STYLUS2); 325 __set_bit(INPUT_PROP_DIRECT, input->propbit); 326 /* 327 * The resolution of these touchscreens is about 10 units/mm, the actual 328 * resolution does not matter much since we set INPUT_PROP_DIRECT. 329 * Userspace wants something here though, so just set it to 10 units/mm. 330 */ 331 input_abs_set_res(input, ABS_X, 10); 332 input_abs_set_res(input, ABS_Y, 10); 333 334 input->name = "Goodix Active Pen"; 335 input->phys = "input/pen"; 336 input->id.bustype = BUS_I2C; 337 input->id.vendor = 0x0416; 338 if (kstrtou16(ts->id, 10, &input->id.product)) 339 input->id.product = 0x1001; 340 input->id.version = ts->version; 341 342 if (input_register_device(input) != 0) { 343 input_free_device(input); 344 return NULL; 345 } 346 347 return input; 348 } 349 350 static void goodix_ts_report_pen_down(struct goodix_ts_data *ts, u8 *data) 351 { 352 int input_x, input_y, input_w; 353 u8 key_value; 354 355 if (!ts->input_pen) { 356 ts->input_pen = goodix_create_pen_input(ts); 357 if (!ts->input_pen) 358 return; 359 } 360 361 if (ts->contact_size == 9) { 362 input_x = get_unaligned_le16(&data[4]); 363 input_y = get_unaligned_le16(&data[6]); 364 input_w = get_unaligned_le16(&data[8]); 365 } else { 366 input_x = get_unaligned_le16(&data[2]); 367 input_y = get_unaligned_le16(&data[4]); 368 input_w = get_unaligned_le16(&data[6]); 369 } 370 371 touchscreen_report_pos(ts->input_pen, &ts->prop, input_x, input_y, false); 372 input_report_abs(ts->input_pen, ABS_PRESSURE, input_w); 373 374 input_report_key(ts->input_pen, BTN_TOUCH, 1); 375 input_report_key(ts->input_pen, BTN_TOOL_PEN, 1); 376 377 if (data[0] & GOODIX_HAVE_KEY) { 378 key_value = data[1 + ts->contact_size]; 379 input_report_key(ts->input_pen, BTN_STYLUS, key_value & 0x10); 380 input_report_key(ts->input_pen, BTN_STYLUS2, key_value & 0x20); 381 } else { 382 input_report_key(ts->input_pen, BTN_STYLUS, 0); 383 input_report_key(ts->input_pen, BTN_STYLUS2, 0); 384 } 385 386 input_sync(ts->input_pen); 387 } 388 389 static void goodix_ts_report_pen_up(struct goodix_ts_data *ts) 390 { 391 if (!ts->input_pen) 392 return; 393 394 input_report_key(ts->input_pen, BTN_TOUCH, 0); 395 input_report_key(ts->input_pen, BTN_TOOL_PEN, 0); 396 input_report_key(ts->input_pen, BTN_STYLUS, 0); 397 input_report_key(ts->input_pen, BTN_STYLUS2, 0); 398 399 input_sync(ts->input_pen); 400 } 401 402 static void goodix_ts_report_touch_8b(struct goodix_ts_data *ts, u8 *coor_data) 403 { 404 int id = coor_data[0] & 0x0F; 405 int input_x = get_unaligned_le16(&coor_data[1]); 406 int input_y = get_unaligned_le16(&coor_data[3]); 407 int input_w = get_unaligned_le16(&coor_data[5]); 408 409 input_mt_slot(ts->input_dev, id); 410 input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true); 411 touchscreen_report_pos(ts->input_dev, &ts->prop, 412 input_x, input_y, true); 413 input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w); 414 input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w); 415 } 416 417 static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data) 418 { 419 int id = coor_data[1] & 0x0F; 420 int input_x = get_unaligned_le16(&coor_data[3]); 421 int input_y = get_unaligned_le16(&coor_data[5]); 422 int input_w = get_unaligned_le16(&coor_data[7]); 423 424 input_mt_slot(ts->input_dev, id); 425 input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true); 426 touchscreen_report_pos(ts->input_dev, &ts->prop, 427 input_x, input_y, true); 428 input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, input_w); 429 input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w); 430 } 431 432 static void goodix_ts_release_keys(struct goodix_ts_data *ts) 433 { 434 int i; 435 436 for (i = 0; i < GOODIX_MAX_KEYS; i++) 437 input_report_key(ts->input_dev, ts->keymap[i], 0); 438 } 439 440 static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data) 441 { 442 int touch_num; 443 u8 key_value; 444 int i; 445 446 if (data[0] & GOODIX_HAVE_KEY) { 447 touch_num = data[0] & 0x0f; 448 key_value = data[1 + ts->contact_size * touch_num]; 449 for (i = 0; i < GOODIX_MAX_KEYS; i++) 450 if (key_value & BIT(i)) 451 input_report_key(ts->input_dev, 452 ts->keymap[i], 1); 453 } else { 454 goodix_ts_release_keys(ts); 455 } 456 } 457 458 /** 459 * goodix_process_events - Process incoming events 460 * 461 * @ts: our goodix_ts_data pointer 462 * 463 * Called when the IRQ is triggered. Read the current device state, and push 464 * the input events to the user space. 465 */ 466 static void goodix_process_events(struct goodix_ts_data *ts) 467 { 468 u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS]; 469 int touch_num; 470 int i; 471 472 touch_num = goodix_ts_read_input_report(ts, point_data); 473 if (touch_num < 0) 474 return; 475 476 /* The pen being down is always reported as a single touch */ 477 if (touch_num == 1 && (point_data[1] & 0x80)) { 478 goodix_ts_report_pen_down(ts, point_data); 479 goodix_ts_release_keys(ts); 480 goto sync; /* Release any previously registered touches */ 481 } else { 482 goodix_ts_report_pen_up(ts); 483 } 484 485 goodix_ts_report_key(ts, point_data); 486 487 for (i = 0; i < touch_num; i++) 488 if (ts->contact_size == 9) 489 goodix_ts_report_touch_9b(ts, 490 &point_data[1 + ts->contact_size * i]); 491 else 492 goodix_ts_report_touch_8b(ts, 493 &point_data[1 + ts->contact_size * i]); 494 495 sync: 496 input_mt_sync_frame(ts->input_dev); 497 input_sync(ts->input_dev); 498 } 499 500 /** 501 * goodix_ts_irq_handler - The IRQ handler 502 * 503 * @irq: interrupt number. 504 * @dev_id: private data pointer. 505 */ 506 static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id) 507 { 508 struct goodix_ts_data *ts = dev_id; 509 510 goodix_process_events(ts); 511 goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0); 512 513 return IRQ_HANDLED; 514 } 515 516 static void goodix_free_irq(struct goodix_ts_data *ts) 517 { 518 devm_free_irq(&ts->client->dev, ts->client->irq, ts); 519 } 520 521 static int goodix_request_irq(struct goodix_ts_data *ts) 522 { 523 return devm_request_threaded_irq(&ts->client->dev, ts->client->irq, 524 NULL, goodix_ts_irq_handler, 525 ts->irq_flags, ts->client->name, ts); 526 } 527 528 static int goodix_check_cfg_8(struct goodix_ts_data *ts, const u8 *cfg, int len) 529 { 530 int i, raw_cfg_len = len - 2; 531 u8 check_sum = 0; 532 533 for (i = 0; i < raw_cfg_len; i++) 534 check_sum += cfg[i]; 535 check_sum = (~check_sum) + 1; 536 if (check_sum != cfg[raw_cfg_len]) { 537 dev_err(&ts->client->dev, 538 "The checksum of the config fw is not correct"); 539 return -EINVAL; 540 } 541 542 if (cfg[raw_cfg_len + 1] != 1) { 543 dev_err(&ts->client->dev, 544 "Config fw must have Config_Fresh register set"); 545 return -EINVAL; 546 } 547 548 return 0; 549 } 550 551 static void goodix_calc_cfg_checksum_8(struct goodix_ts_data *ts) 552 { 553 int i, raw_cfg_len = ts->chip->config_len - 2; 554 u8 check_sum = 0; 555 556 for (i = 0; i < raw_cfg_len; i++) 557 check_sum += ts->config[i]; 558 check_sum = (~check_sum) + 1; 559 560 ts->config[raw_cfg_len] = check_sum; 561 ts->config[raw_cfg_len + 1] = 1; /* Set "config_fresh" bit */ 562 } 563 564 static int goodix_check_cfg_16(struct goodix_ts_data *ts, const u8 *cfg, 565 int len) 566 { 567 int i, raw_cfg_len = len - 3; 568 u16 check_sum = 0; 569 570 for (i = 0; i < raw_cfg_len; i += 2) 571 check_sum += get_unaligned_be16(&cfg[i]); 572 check_sum = (~check_sum) + 1; 573 if (check_sum != get_unaligned_be16(&cfg[raw_cfg_len])) { 574 dev_err(&ts->client->dev, 575 "The checksum of the config fw is not correct"); 576 return -EINVAL; 577 } 578 579 if (cfg[raw_cfg_len + 2] != 1) { 580 dev_err(&ts->client->dev, 581 "Config fw must have Config_Fresh register set"); 582 return -EINVAL; 583 } 584 585 return 0; 586 } 587 588 static void goodix_calc_cfg_checksum_16(struct goodix_ts_data *ts) 589 { 590 int i, raw_cfg_len = ts->chip->config_len - 3; 591 u16 check_sum = 0; 592 593 for (i = 0; i < raw_cfg_len; i += 2) 594 check_sum += get_unaligned_be16(&ts->config[i]); 595 check_sum = (~check_sum) + 1; 596 597 put_unaligned_be16(check_sum, &ts->config[raw_cfg_len]); 598 ts->config[raw_cfg_len + 2] = 1; /* Set "config_fresh" bit */ 599 } 600 601 /** 602 * goodix_check_cfg - Checks if config fw is valid 603 * 604 * @ts: goodix_ts_data pointer 605 * @cfg: firmware config data 606 * @len: config data length 607 */ 608 static int goodix_check_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len) 609 { 610 if (len < GOODIX_CONFIG_MIN_LENGTH || 611 len > GOODIX_CONFIG_MAX_LENGTH) { 612 dev_err(&ts->client->dev, 613 "The length of the config fw is not correct"); 614 return -EINVAL; 615 } 616 617 return ts->chip->check_config(ts, cfg, len); 618 } 619 620 /** 621 * goodix_send_cfg - Write fw config to device 622 * 623 * @ts: goodix_ts_data pointer 624 * @cfg: config firmware to write to device 625 * @len: config data length 626 */ 627 int goodix_send_cfg(struct goodix_ts_data *ts, const u8 *cfg, int len) 628 { 629 int error; 630 631 error = goodix_check_cfg(ts, cfg, len); 632 if (error) 633 return error; 634 635 error = goodix_i2c_write(ts->client, ts->chip->config_addr, cfg, len); 636 if (error) 637 return error; 638 639 dev_dbg(&ts->client->dev, "Config sent successfully."); 640 641 /* Let the firmware reconfigure itself, so sleep for 10ms */ 642 usleep_range(10000, 11000); 643 644 return 0; 645 } 646 647 #ifdef ACPI_GPIO_SUPPORT 648 static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts) 649 { 650 acpi_handle handle = ACPI_HANDLE(&ts->client->dev); 651 acpi_status status; 652 653 status = acpi_evaluate_object(handle, "INTI", NULL, NULL); 654 return ACPI_SUCCESS(status) ? 0 : -EIO; 655 } 656 657 static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value) 658 { 659 acpi_handle handle = ACPI_HANDLE(&ts->client->dev); 660 acpi_status status; 661 662 status = acpi_execute_simple_method(handle, "INTO", value); 663 return ACPI_SUCCESS(status) ? 0 : -EIO; 664 } 665 #else 666 static int goodix_pin_acpi_direction_input(struct goodix_ts_data *ts) 667 { 668 dev_err(&ts->client->dev, 669 "%s called on device without ACPI support\n", __func__); 670 return -EINVAL; 671 } 672 673 static int goodix_pin_acpi_output_method(struct goodix_ts_data *ts, int value) 674 { 675 dev_err(&ts->client->dev, 676 "%s called on device without ACPI support\n", __func__); 677 return -EINVAL; 678 } 679 #endif 680 681 static int goodix_irq_direction_output(struct goodix_ts_data *ts, int value) 682 { 683 switch (ts->irq_pin_access_method) { 684 case IRQ_PIN_ACCESS_NONE: 685 dev_err(&ts->client->dev, 686 "%s called without an irq_pin_access_method set\n", 687 __func__); 688 return -EINVAL; 689 case IRQ_PIN_ACCESS_GPIO: 690 return gpiod_direction_output(ts->gpiod_int, value); 691 case IRQ_PIN_ACCESS_ACPI_GPIO: 692 /* 693 * The IRQ pin triggers on a falling edge, so its gets marked 694 * as active-low, use output_raw to avoid the value inversion. 695 */ 696 return gpiod_direction_output_raw(ts->gpiod_int, value); 697 case IRQ_PIN_ACCESS_ACPI_METHOD: 698 return goodix_pin_acpi_output_method(ts, value); 699 } 700 701 return -EINVAL; /* Never reached */ 702 } 703 704 static int goodix_irq_direction_input(struct goodix_ts_data *ts) 705 { 706 switch (ts->irq_pin_access_method) { 707 case IRQ_PIN_ACCESS_NONE: 708 dev_err(&ts->client->dev, 709 "%s called without an irq_pin_access_method set\n", 710 __func__); 711 return -EINVAL; 712 case IRQ_PIN_ACCESS_GPIO: 713 return gpiod_direction_input(ts->gpiod_int); 714 case IRQ_PIN_ACCESS_ACPI_GPIO: 715 return gpiod_direction_input(ts->gpiod_int); 716 case IRQ_PIN_ACCESS_ACPI_METHOD: 717 return goodix_pin_acpi_direction_input(ts); 718 } 719 720 return -EINVAL; /* Never reached */ 721 } 722 723 int goodix_int_sync(struct goodix_ts_data *ts) 724 { 725 int error; 726 727 error = goodix_irq_direction_output(ts, 0); 728 if (error) 729 goto error; 730 731 msleep(50); /* T5: 50ms */ 732 733 error = goodix_irq_direction_input(ts); 734 if (error) 735 goto error; 736 737 return 0; 738 739 error: 740 dev_err(&ts->client->dev, "Controller irq sync failed.\n"); 741 return error; 742 } 743 744 /** 745 * goodix_reset_no_int_sync - Reset device, leaving interrupt line in output mode 746 * 747 * @ts: goodix_ts_data pointer 748 */ 749 int goodix_reset_no_int_sync(struct goodix_ts_data *ts) 750 { 751 int error; 752 753 /* begin select I2C slave addr */ 754 error = gpiod_direction_output(ts->gpiod_rst, 0); 755 if (error) 756 goto error; 757 758 msleep(20); /* T2: > 10ms */ 759 760 /* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */ 761 error = goodix_irq_direction_output(ts, ts->client->addr == 0x14); 762 if (error) 763 goto error; 764 765 usleep_range(100, 2000); /* T3: > 100us */ 766 767 error = gpiod_direction_output(ts->gpiod_rst, 1); 768 if (error) 769 goto error; 770 771 usleep_range(6000, 10000); /* T4: > 5ms */ 772 773 /* 774 * Put the reset pin back in to input / high-impedance mode to save 775 * power. Only do this in the non ACPI case since some ACPI boards 776 * don't have a pull-up, so there the reset pin must stay active-high. 777 */ 778 if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_GPIO) { 779 error = gpiod_direction_input(ts->gpiod_rst); 780 if (error) 781 goto error; 782 } 783 784 return 0; 785 786 error: 787 dev_err(&ts->client->dev, "Controller reset failed.\n"); 788 return error; 789 } 790 791 /** 792 * goodix_reset - Reset device during power on 793 * 794 * @ts: goodix_ts_data pointer 795 */ 796 static int goodix_reset(struct goodix_ts_data *ts) 797 { 798 int error; 799 800 error = goodix_reset_no_int_sync(ts); 801 if (error) 802 return error; 803 804 return goodix_int_sync(ts); 805 } 806 807 #ifdef ACPI_GPIO_SUPPORT 808 #include <asm/cpu_device_id.h> 809 #include <asm/intel-family.h> 810 811 static const struct x86_cpu_id baytrail_cpu_ids[] = { 812 { X86_VENDOR_INTEL, 6, INTEL_FAM6_ATOM_SILVERMONT, X86_FEATURE_ANY, }, 813 {} 814 }; 815 816 static inline bool is_byt(void) 817 { 818 const struct x86_cpu_id *id = x86_match_cpu(baytrail_cpu_ids); 819 820 return !!id; 821 } 822 823 static const struct acpi_gpio_params first_gpio = { 0, 0, false }; 824 static const struct acpi_gpio_params second_gpio = { 1, 0, false }; 825 826 static const struct acpi_gpio_mapping acpi_goodix_int_first_gpios[] = { 827 { GOODIX_GPIO_INT_NAME "-gpios", &first_gpio, 1 }, 828 { GOODIX_GPIO_RST_NAME "-gpios", &second_gpio, 1 }, 829 { }, 830 }; 831 832 static const struct acpi_gpio_mapping acpi_goodix_int_last_gpios[] = { 833 { GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 }, 834 { GOODIX_GPIO_INT_NAME "-gpios", &second_gpio, 1 }, 835 { }, 836 }; 837 838 static const struct acpi_gpio_mapping acpi_goodix_reset_only_gpios[] = { 839 { GOODIX_GPIO_RST_NAME "-gpios", &first_gpio, 1 }, 840 { }, 841 }; 842 843 static int goodix_resource(struct acpi_resource *ares, void *data) 844 { 845 struct goodix_ts_data *ts = data; 846 struct device *dev = &ts->client->dev; 847 struct acpi_resource_gpio *gpio; 848 849 switch (ares->type) { 850 case ACPI_RESOURCE_TYPE_GPIO: 851 gpio = &ares->data.gpio; 852 if (gpio->connection_type == ACPI_RESOURCE_GPIO_TYPE_INT) { 853 if (ts->gpio_int_idx == -1) { 854 ts->gpio_int_idx = ts->gpio_count; 855 } else { 856 dev_err(dev, "More then one GpioInt resource, ignoring ACPI GPIO resources\n"); 857 ts->gpio_int_idx = -2; 858 } 859 } 860 ts->gpio_count++; 861 break; 862 default: 863 break; 864 } 865 866 return 0; 867 } 868 869 /* 870 * This function gets called in case we fail to get the irq GPIO directly 871 * because the ACPI tables lack GPIO-name to APCI _CRS index mappings 872 * (no _DSD UUID daffd814-6eba-4d8c-8a91-bc9bbf4aa301 data). 873 * In that case we add our own mapping and then goodix_get_gpio_config() 874 * retries to get the GPIOs based on the added mapping. 875 */ 876 static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts) 877 { 878 const struct acpi_gpio_mapping *gpio_mapping = NULL; 879 struct device *dev = &ts->client->dev; 880 LIST_HEAD(resources); 881 int ret; 882 883 ts->gpio_count = 0; 884 ts->gpio_int_idx = -1; 885 ret = acpi_dev_get_resources(ACPI_COMPANION(dev), &resources, 886 goodix_resource, ts); 887 if (ret < 0) { 888 dev_err(dev, "Error getting ACPI resources: %d\n", ret); 889 return ret; 890 } 891 892 acpi_dev_free_resource_list(&resources); 893 894 if (ts->gpio_count == 2 && ts->gpio_int_idx == 0) { 895 ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO; 896 gpio_mapping = acpi_goodix_int_first_gpios; 897 } else if (ts->gpio_count == 2 && ts->gpio_int_idx == 1) { 898 ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO; 899 gpio_mapping = acpi_goodix_int_last_gpios; 900 } else if (ts->gpio_count == 1 && ts->gpio_int_idx == -1 && 901 acpi_has_method(ACPI_HANDLE(dev), "INTI") && 902 acpi_has_method(ACPI_HANDLE(dev), "INTO")) { 903 dev_info(dev, "Using ACPI INTI and INTO methods for IRQ pin access\n"); 904 ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_METHOD; 905 gpio_mapping = acpi_goodix_reset_only_gpios; 906 } else if (is_byt() && ts->gpio_count == 2 && ts->gpio_int_idx == -1) { 907 dev_info(dev, "No ACPI GpioInt resource, assuming that the GPIO order is reset, int\n"); 908 ts->irq_pin_access_method = IRQ_PIN_ACCESS_ACPI_GPIO; 909 gpio_mapping = acpi_goodix_int_last_gpios; 910 } else { 911 dev_warn(dev, "Unexpected ACPI resources: gpio_count %d, gpio_int_idx %d\n", 912 ts->gpio_count, ts->gpio_int_idx); 913 return -EINVAL; 914 } 915 916 /* 917 * Normally we put the reset pin in input / high-impedance mode to save 918 * power. But some x86/ACPI boards don't have a pull-up, so for the ACPI 919 * case, leave the pin as is. This results in the pin not being touched 920 * at all on x86/ACPI boards, except when needed for error-recover. 921 */ 922 ts->gpiod_rst_flags = GPIOD_ASIS; 923 924 return devm_acpi_dev_add_driver_gpios(dev, gpio_mapping); 925 } 926 #else 927 static int goodix_add_acpi_gpio_mappings(struct goodix_ts_data *ts) 928 { 929 return -EINVAL; 930 } 931 #endif /* CONFIG_X86 && CONFIG_ACPI */ 932 933 /** 934 * goodix_get_gpio_config - Get GPIO config from ACPI/DT 935 * 936 * @ts: goodix_ts_data pointer 937 */ 938 static int goodix_get_gpio_config(struct goodix_ts_data *ts) 939 { 940 int error; 941 struct device *dev; 942 struct gpio_desc *gpiod; 943 bool added_acpi_mappings = false; 944 945 if (!ts->client) 946 return -EINVAL; 947 dev = &ts->client->dev; 948 949 /* 950 * By default we request the reset pin as input, leaving it in 951 * high-impedance when not resetting the controller to save power. 952 */ 953 ts->gpiod_rst_flags = GPIOD_IN; 954 955 ts->avdd28 = devm_regulator_get(dev, "AVDD28"); 956 if (IS_ERR(ts->avdd28)) { 957 error = PTR_ERR(ts->avdd28); 958 if (error != -EPROBE_DEFER) 959 dev_err(dev, 960 "Failed to get AVDD28 regulator: %d\n", error); 961 return error; 962 } 963 964 ts->vddio = devm_regulator_get(dev, "VDDIO"); 965 if (IS_ERR(ts->vddio)) { 966 error = PTR_ERR(ts->vddio); 967 if (error != -EPROBE_DEFER) 968 dev_err(dev, 969 "Failed to get VDDIO regulator: %d\n", error); 970 return error; 971 } 972 973 retry_get_irq_gpio: 974 /* Get the interrupt GPIO pin number */ 975 gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN); 976 if (IS_ERR(gpiod)) { 977 error = PTR_ERR(gpiod); 978 if (error != -EPROBE_DEFER) 979 dev_err(dev, "Failed to get %s GPIO: %d\n", 980 GOODIX_GPIO_INT_NAME, error); 981 return error; 982 } 983 if (!gpiod && has_acpi_companion(dev) && !added_acpi_mappings) { 984 added_acpi_mappings = true; 985 if (goodix_add_acpi_gpio_mappings(ts) == 0) 986 goto retry_get_irq_gpio; 987 } 988 989 ts->gpiod_int = gpiod; 990 991 /* Get the reset line GPIO pin number */ 992 gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, ts->gpiod_rst_flags); 993 if (IS_ERR(gpiod)) { 994 error = PTR_ERR(gpiod); 995 if (error != -EPROBE_DEFER) 996 dev_err(dev, "Failed to get %s GPIO: %d\n", 997 GOODIX_GPIO_RST_NAME, error); 998 return error; 999 } 1000 1001 ts->gpiod_rst = gpiod; 1002 1003 switch (ts->irq_pin_access_method) { 1004 case IRQ_PIN_ACCESS_ACPI_GPIO: 1005 /* 1006 * We end up here if goodix_add_acpi_gpio_mappings() has 1007 * called devm_acpi_dev_add_driver_gpios() because the ACPI 1008 * tables did not contain name to index mappings. 1009 * Check that we successfully got both GPIOs after we've 1010 * added our own acpi_gpio_mapping and if we did not get both 1011 * GPIOs reset irq_pin_access_method to IRQ_PIN_ACCESS_NONE. 1012 */ 1013 if (!ts->gpiod_int || !ts->gpiod_rst) 1014 ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE; 1015 break; 1016 case IRQ_PIN_ACCESS_ACPI_METHOD: 1017 if (!ts->gpiod_rst) 1018 ts->irq_pin_access_method = IRQ_PIN_ACCESS_NONE; 1019 break; 1020 default: 1021 if (ts->gpiod_int && ts->gpiod_rst) { 1022 ts->reset_controller_at_probe = true; 1023 ts->load_cfg_from_disk = true; 1024 ts->irq_pin_access_method = IRQ_PIN_ACCESS_GPIO; 1025 } 1026 } 1027 1028 return 0; 1029 } 1030 1031 /** 1032 * goodix_read_config - Read the embedded configuration of the panel 1033 * 1034 * @ts: our goodix_ts_data pointer 1035 * 1036 * Must be called during probe 1037 */ 1038 static void goodix_read_config(struct goodix_ts_data *ts) 1039 { 1040 int x_max, y_max; 1041 int error; 1042 1043 /* 1044 * On controllers where we need to upload the firmware 1045 * (controllers without flash) ts->config already has the config 1046 * at this point and the controller itself does not have it yet! 1047 */ 1048 if (!ts->firmware_name) { 1049 error = goodix_i2c_read(ts->client, ts->chip->config_addr, 1050 ts->config, ts->chip->config_len); 1051 if (error) { 1052 ts->int_trigger_type = GOODIX_INT_TRIGGER; 1053 ts->max_touch_num = GOODIX_MAX_CONTACTS; 1054 return; 1055 } 1056 } 1057 1058 ts->int_trigger_type = ts->config[TRIGGER_LOC] & 0x03; 1059 ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f; 1060 1061 x_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC]); 1062 y_max = get_unaligned_le16(&ts->config[RESOLUTION_LOC + 2]); 1063 if (x_max && y_max) { 1064 input_abs_set_max(ts->input_dev, ABS_MT_POSITION_X, x_max - 1); 1065 input_abs_set_max(ts->input_dev, ABS_MT_POSITION_Y, y_max - 1); 1066 } 1067 1068 ts->chip->calc_config_checksum(ts); 1069 } 1070 1071 /** 1072 * goodix_read_version - Read goodix touchscreen version 1073 * 1074 * @ts: our goodix_ts_data pointer 1075 */ 1076 static int goodix_read_version(struct goodix_ts_data *ts) 1077 { 1078 int error; 1079 u8 buf[6]; 1080 char id_str[GOODIX_ID_MAX_LEN + 1]; 1081 1082 error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf)); 1083 if (error) 1084 return error; 1085 1086 memcpy(id_str, buf, GOODIX_ID_MAX_LEN); 1087 id_str[GOODIX_ID_MAX_LEN] = 0; 1088 strscpy(ts->id, id_str, GOODIX_ID_MAX_LEN + 1); 1089 1090 ts->version = get_unaligned_le16(&buf[4]); 1091 1092 dev_info(&ts->client->dev, "ID %s, version: %04x\n", ts->id, 1093 ts->version); 1094 1095 return 0; 1096 } 1097 1098 /** 1099 * goodix_i2c_test - I2C test function to check if the device answers. 1100 * 1101 * @client: the i2c client 1102 */ 1103 static int goodix_i2c_test(struct i2c_client *client) 1104 { 1105 int retry = 0; 1106 int error; 1107 u8 test; 1108 1109 while (retry++ < 2) { 1110 error = goodix_i2c_read(client, GOODIX_REG_ID, &test, 1); 1111 if (!error) 1112 return 0; 1113 1114 msleep(20); 1115 } 1116 1117 return error; 1118 } 1119 1120 /** 1121 * goodix_configure_dev - Finish device initialization 1122 * 1123 * @ts: our goodix_ts_data pointer 1124 * 1125 * Must be called from probe to finish initialization of the device. 1126 * Contains the common initialization code for both devices that 1127 * declare gpio pins and devices that do not. It is either called 1128 * directly from probe or from request_firmware_wait callback. 1129 */ 1130 static int goodix_configure_dev(struct goodix_ts_data *ts) 1131 { 1132 int error; 1133 int i; 1134 1135 ts->int_trigger_type = GOODIX_INT_TRIGGER; 1136 ts->max_touch_num = GOODIX_MAX_CONTACTS; 1137 1138 ts->input_dev = devm_input_allocate_device(&ts->client->dev); 1139 if (!ts->input_dev) { 1140 dev_err(&ts->client->dev, "Failed to allocate input device."); 1141 return -ENOMEM; 1142 } 1143 1144 ts->input_dev->name = "Goodix Capacitive TouchScreen"; 1145 ts->input_dev->phys = "input/ts"; 1146 ts->input_dev->id.bustype = BUS_I2C; 1147 ts->input_dev->id.vendor = 0x0416; 1148 if (kstrtou16(ts->id, 10, &ts->input_dev->id.product)) 1149 ts->input_dev->id.product = 0x1001; 1150 ts->input_dev->id.version = ts->version; 1151 1152 ts->input_dev->keycode = ts->keymap; 1153 ts->input_dev->keycodesize = sizeof(ts->keymap[0]); 1154 ts->input_dev->keycodemax = GOODIX_MAX_KEYS; 1155 1156 /* Capacitive Windows/Home button on some devices */ 1157 for (i = 0; i < GOODIX_MAX_KEYS; ++i) { 1158 if (i == 0) 1159 ts->keymap[i] = KEY_LEFTMETA; 1160 else 1161 ts->keymap[i] = KEY_F1 + (i - 1); 1162 1163 input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]); 1164 } 1165 1166 input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X); 1167 input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y); 1168 input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR, 0, 255, 0, 0); 1169 input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0); 1170 1171 /* Read configuration and apply touchscreen parameters */ 1172 goodix_read_config(ts); 1173 1174 /* Try overriding touchscreen parameters via device properties */ 1175 touchscreen_parse_properties(ts->input_dev, true, &ts->prop); 1176 1177 if (!ts->prop.max_x || !ts->prop.max_y || !ts->max_touch_num) { 1178 dev_err(&ts->client->dev, 1179 "Invalid config (%d, %d, %d), using defaults\n", 1180 ts->prop.max_x, ts->prop.max_y, ts->max_touch_num); 1181 ts->prop.max_x = GOODIX_MAX_WIDTH - 1; 1182 ts->prop.max_y = GOODIX_MAX_HEIGHT - 1; 1183 ts->max_touch_num = GOODIX_MAX_CONTACTS; 1184 input_abs_set_max(ts->input_dev, 1185 ABS_MT_POSITION_X, ts->prop.max_x); 1186 input_abs_set_max(ts->input_dev, 1187 ABS_MT_POSITION_Y, ts->prop.max_y); 1188 } 1189 1190 if (dmi_check_system(nine_bytes_report)) { 1191 ts->contact_size = 9; 1192 1193 dev_dbg(&ts->client->dev, 1194 "Non-standard 9-bytes report format quirk\n"); 1195 } 1196 1197 if (dmi_check_system(inverted_x_screen)) { 1198 ts->prop.invert_x = true; 1199 dev_dbg(&ts->client->dev, 1200 "Applying 'inverted x screen' quirk\n"); 1201 } 1202 1203 error = input_mt_init_slots(ts->input_dev, ts->max_touch_num, 1204 INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED); 1205 if (error) { 1206 dev_err(&ts->client->dev, 1207 "Failed to initialize MT slots: %d", error); 1208 return error; 1209 } 1210 1211 error = input_register_device(ts->input_dev); 1212 if (error) { 1213 dev_err(&ts->client->dev, 1214 "Failed to register input device: %d", error); 1215 return error; 1216 } 1217 1218 ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT; 1219 error = goodix_request_irq(ts); 1220 if (error) { 1221 dev_err(&ts->client->dev, "request IRQ failed: %d\n", error); 1222 return error; 1223 } 1224 1225 return 0; 1226 } 1227 1228 /** 1229 * goodix_config_cb - Callback to finish device init 1230 * 1231 * @cfg: firmware config 1232 * @ctx: our goodix_ts_data pointer 1233 * 1234 * request_firmware_wait callback that finishes 1235 * initialization of the device. 1236 */ 1237 static void goodix_config_cb(const struct firmware *cfg, void *ctx) 1238 { 1239 struct goodix_ts_data *ts = ctx; 1240 int error; 1241 1242 if (ts->firmware_name) { 1243 if (!cfg) 1244 goto err_release_cfg; 1245 1246 error = goodix_check_cfg(ts, cfg->data, cfg->size); 1247 if (error) 1248 goto err_release_cfg; 1249 1250 memcpy(ts->config, cfg->data, cfg->size); 1251 } else if (cfg) { 1252 /* send device configuration to the firmware */ 1253 error = goodix_send_cfg(ts, cfg->data, cfg->size); 1254 if (error) 1255 goto err_release_cfg; 1256 } 1257 1258 goodix_configure_dev(ts); 1259 1260 err_release_cfg: 1261 release_firmware(cfg); 1262 complete_all(&ts->firmware_loading_complete); 1263 } 1264 1265 static void goodix_disable_regulators(void *arg) 1266 { 1267 struct goodix_ts_data *ts = arg; 1268 1269 regulator_disable(ts->vddio); 1270 regulator_disable(ts->avdd28); 1271 } 1272 1273 static int goodix_ts_probe(struct i2c_client *client, 1274 const struct i2c_device_id *id) 1275 { 1276 struct goodix_ts_data *ts; 1277 const char *cfg_name; 1278 int error; 1279 1280 dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr); 1281 1282 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { 1283 dev_err(&client->dev, "I2C check functionality failed.\n"); 1284 return -ENXIO; 1285 } 1286 1287 ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL); 1288 if (!ts) 1289 return -ENOMEM; 1290 1291 ts->client = client; 1292 i2c_set_clientdata(client, ts); 1293 init_completion(&ts->firmware_loading_complete); 1294 ts->contact_size = GOODIX_CONTACT_SIZE; 1295 1296 error = goodix_get_gpio_config(ts); 1297 if (error) 1298 return error; 1299 1300 /* power up the controller */ 1301 error = regulator_enable(ts->avdd28); 1302 if (error) { 1303 dev_err(&client->dev, 1304 "Failed to enable AVDD28 regulator: %d\n", 1305 error); 1306 return error; 1307 } 1308 1309 error = regulator_enable(ts->vddio); 1310 if (error) { 1311 dev_err(&client->dev, 1312 "Failed to enable VDDIO regulator: %d\n", 1313 error); 1314 regulator_disable(ts->avdd28); 1315 return error; 1316 } 1317 1318 error = devm_add_action_or_reset(&client->dev, 1319 goodix_disable_regulators, ts); 1320 if (error) 1321 return error; 1322 1323 reset: 1324 if (ts->reset_controller_at_probe) { 1325 /* reset the controller */ 1326 error = goodix_reset(ts); 1327 if (error) 1328 return error; 1329 } 1330 1331 error = goodix_i2c_test(client); 1332 if (error) { 1333 if (!ts->reset_controller_at_probe && 1334 ts->irq_pin_access_method != IRQ_PIN_ACCESS_NONE) { 1335 /* Retry after a controller reset */ 1336 ts->reset_controller_at_probe = true; 1337 goto reset; 1338 } 1339 dev_err(&client->dev, "I2C communication failure: %d\n", error); 1340 return error; 1341 } 1342 1343 error = goodix_firmware_check(ts); 1344 if (error) 1345 return error; 1346 1347 error = goodix_read_version(ts); 1348 if (error) 1349 return error; 1350 1351 ts->chip = goodix_get_chip_data(ts->id); 1352 1353 if (ts->load_cfg_from_disk) { 1354 /* update device config */ 1355 error = device_property_read_string(&client->dev, 1356 "goodix,config-name", 1357 &cfg_name); 1358 if (!error) 1359 snprintf(ts->cfg_name, sizeof(ts->cfg_name), 1360 "goodix/%s", cfg_name); 1361 else 1362 snprintf(ts->cfg_name, sizeof(ts->cfg_name), 1363 "goodix_%s_cfg.bin", ts->id); 1364 1365 error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name, 1366 &client->dev, GFP_KERNEL, ts, 1367 goodix_config_cb); 1368 if (error) { 1369 dev_err(&client->dev, 1370 "Failed to invoke firmware loader: %d\n", 1371 error); 1372 return error; 1373 } 1374 1375 return 0; 1376 } else { 1377 error = goodix_configure_dev(ts); 1378 if (error) 1379 return error; 1380 } 1381 1382 return 0; 1383 } 1384 1385 static int goodix_ts_remove(struct i2c_client *client) 1386 { 1387 struct goodix_ts_data *ts = i2c_get_clientdata(client); 1388 1389 if (ts->load_cfg_from_disk) 1390 wait_for_completion(&ts->firmware_loading_complete); 1391 1392 return 0; 1393 } 1394 1395 static int __maybe_unused goodix_suspend(struct device *dev) 1396 { 1397 struct i2c_client *client = to_i2c_client(dev); 1398 struct goodix_ts_data *ts = i2c_get_clientdata(client); 1399 int error; 1400 1401 if (ts->load_cfg_from_disk) 1402 wait_for_completion(&ts->firmware_loading_complete); 1403 1404 /* We need gpio pins to suspend/resume */ 1405 if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) { 1406 disable_irq(client->irq); 1407 return 0; 1408 } 1409 1410 /* Free IRQ as IRQ pin is used as output in the suspend sequence */ 1411 goodix_free_irq(ts); 1412 1413 /* Save reference (calibration) info if necessary */ 1414 goodix_save_bak_ref(ts); 1415 1416 /* Output LOW on the INT pin for 5 ms */ 1417 error = goodix_irq_direction_output(ts, 0); 1418 if (error) { 1419 goodix_request_irq(ts); 1420 return error; 1421 } 1422 1423 usleep_range(5000, 6000); 1424 1425 error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND, 1426 GOODIX_CMD_SCREEN_OFF); 1427 if (error) { 1428 goodix_irq_direction_input(ts); 1429 goodix_request_irq(ts); 1430 return -EAGAIN; 1431 } 1432 1433 /* 1434 * The datasheet specifies that the interval between sending screen-off 1435 * command and wake-up should be longer than 58 ms. To avoid waking up 1436 * sooner, delay 58ms here. 1437 */ 1438 msleep(58); 1439 return 0; 1440 } 1441 1442 static int __maybe_unused goodix_resume(struct device *dev) 1443 { 1444 struct i2c_client *client = to_i2c_client(dev); 1445 struct goodix_ts_data *ts = i2c_get_clientdata(client); 1446 u8 config_ver; 1447 int error; 1448 1449 if (ts->irq_pin_access_method == IRQ_PIN_ACCESS_NONE) { 1450 enable_irq(client->irq); 1451 return 0; 1452 } 1453 1454 /* 1455 * Exit sleep mode by outputting HIGH level to INT pin 1456 * for 2ms~5ms. 1457 */ 1458 error = goodix_irq_direction_output(ts, 1); 1459 if (error) 1460 return error; 1461 1462 usleep_range(2000, 5000); 1463 1464 error = goodix_int_sync(ts); 1465 if (error) 1466 return error; 1467 1468 error = goodix_i2c_read(ts->client, ts->chip->config_addr, 1469 &config_ver, 1); 1470 if (!error && config_ver != ts->config[0]) 1471 dev_info(dev, "Config version mismatch %d != %d, resetting controller\n", 1472 config_ver, ts->config[0]); 1473 1474 if (error != 0 || config_ver != ts->config[0]) { 1475 error = goodix_reset(ts); 1476 if (error) 1477 return error; 1478 1479 error = goodix_send_cfg(ts, ts->config, ts->chip->config_len); 1480 if (error) 1481 return error; 1482 } 1483 1484 error = goodix_request_irq(ts); 1485 if (error) 1486 return error; 1487 1488 return 0; 1489 } 1490 1491 static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume); 1492 1493 static const struct i2c_device_id goodix_ts_id[] = { 1494 { "GDIX1001:00", 0 }, 1495 { } 1496 }; 1497 MODULE_DEVICE_TABLE(i2c, goodix_ts_id); 1498 1499 #ifdef CONFIG_ACPI 1500 static const struct acpi_device_id goodix_acpi_match[] = { 1501 { "GDIX1001", 0 }, 1502 { "GDIX1002", 0 }, 1503 { } 1504 }; 1505 MODULE_DEVICE_TABLE(acpi, goodix_acpi_match); 1506 #endif 1507 1508 #ifdef CONFIG_OF 1509 static const struct of_device_id goodix_of_match[] = { 1510 { .compatible = "goodix,gt1151" }, 1511 { .compatible = "goodix,gt5663" }, 1512 { .compatible = "goodix,gt5688" }, 1513 { .compatible = "goodix,gt911" }, 1514 { .compatible = "goodix,gt9110" }, 1515 { .compatible = "goodix,gt912" }, 1516 { .compatible = "goodix,gt9147" }, 1517 { .compatible = "goodix,gt917s" }, 1518 { .compatible = "goodix,gt927" }, 1519 { .compatible = "goodix,gt9271" }, 1520 { .compatible = "goodix,gt928" }, 1521 { .compatible = "goodix,gt9286" }, 1522 { .compatible = "goodix,gt967" }, 1523 { } 1524 }; 1525 MODULE_DEVICE_TABLE(of, goodix_of_match); 1526 #endif 1527 1528 static struct i2c_driver goodix_ts_driver = { 1529 .probe = goodix_ts_probe, 1530 .remove = goodix_ts_remove, 1531 .id_table = goodix_ts_id, 1532 .driver = { 1533 .name = "Goodix-TS", 1534 .acpi_match_table = ACPI_PTR(goodix_acpi_match), 1535 .of_match_table = of_match_ptr(goodix_of_match), 1536 .pm = &goodix_pm_ops, 1537 }, 1538 }; 1539 module_i2c_driver(goodix_ts_driver); 1540 1541 MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>"); 1542 MODULE_AUTHOR("Bastien Nocera <hadess@hadess.net>"); 1543 MODULE_DESCRIPTION("Goodix touchscreen driver"); 1544 MODULE_LICENSE("GPL v2"); 1545