1 /* 2 * Copyright (c) 2008, 2009 QLogic Corporation. All rights reserved. 3 * 4 * This software is available to you under a choice of one of two 5 * licenses. You may choose to be licensed under the terms of the GNU 6 * General Public License (GPL) Version 2, available from the file 7 * COPYING in the main directory of this source tree, or the 8 * OpenIB.org BSD license below: 9 * 10 * Redistribution and use in source and binary forms, with or 11 * without modification, are permitted provided that the following 12 * conditions are met: 13 * 14 * - Redistributions of source code must retain the above 15 * copyright notice, this list of conditions and the following 16 * disclaimer. 17 * 18 * - Redistributions in binary form must reproduce the above 19 * copyright notice, this list of conditions and the following 20 * disclaimer in the documentation and/or other materials 21 * provided with the distribution. 22 * 23 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, 24 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF 25 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 26 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS 27 * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN 28 * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN 29 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE 30 * SOFTWARE. 31 */ 32 33 #include <linux/pci.h> 34 #include <linux/io.h> 35 #include <linux/delay.h> 36 #include <linux/vmalloc.h> 37 #include <linux/aer.h> 38 #include <linux/module.h> 39 40 #include "qib.h" 41 42 /* 43 * This file contains PCIe utility routines that are common to the 44 * various QLogic InfiniPath adapters 45 */ 46 47 /* 48 * Code to adjust PCIe capabilities. 49 * To minimize the change footprint, we call it 50 * from qib_pcie_params, which every chip-specific 51 * file calls, even though this violates some 52 * expectations of harmlessness. 53 */ 54 static int qib_tune_pcie_caps(struct qib_devdata *); 55 static int qib_tune_pcie_coalesce(struct qib_devdata *); 56 57 /* 58 * Do all the common PCIe setup and initialization. 59 * devdata is not yet allocated, and is not allocated until after this 60 * routine returns success. Therefore qib_dev_err() can't be used for error 61 * printing. 62 */ 63 int qib_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent) 64 { 65 int ret; 66 67 ret = pci_enable_device(pdev); 68 if (ret) { 69 /* 70 * This can happen (in theory) iff: 71 * We did a chip reset, and then failed to reprogram the 72 * BAR, or the chip reset due to an internal error. We then 73 * unloaded the driver and reloaded it. 74 * 75 * Both reset cases set the BAR back to initial state. For 76 * the latter case, the AER sticky error bit at offset 0x718 77 * should be set, but the Linux kernel doesn't yet know 78 * about that, it appears. If the original BAR was retained 79 * in the kernel data structures, this may be OK. 80 */ 81 qib_early_err(&pdev->dev, "pci enable failed: error %d\n", 82 -ret); 83 goto done; 84 } 85 86 ret = pci_request_regions(pdev, QIB_DRV_NAME); 87 if (ret) { 88 qib_devinfo(pdev, "pci_request_regions fails: err %d\n", -ret); 89 goto bail; 90 } 91 92 ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64)); 93 if (ret) { 94 /* 95 * If the 64 bit setup fails, try 32 bit. Some systems 96 * do not setup 64 bit maps on systems with 2GB or less 97 * memory installed. 98 */ 99 ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); 100 if (ret) { 101 qib_devinfo(pdev, "Unable to set DMA mask: %d\n", ret); 102 goto bail; 103 } 104 ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); 105 } else 106 ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); 107 if (ret) { 108 qib_early_err(&pdev->dev, 109 "Unable to set DMA consistent mask: %d\n", ret); 110 goto bail; 111 } 112 113 pci_set_master(pdev); 114 ret = pci_enable_pcie_error_reporting(pdev); 115 if (ret) { 116 qib_early_err(&pdev->dev, 117 "Unable to enable pcie error reporting: %d\n", 118 ret); 119 ret = 0; 120 } 121 goto done; 122 123 bail: 124 pci_disable_device(pdev); 125 pci_release_regions(pdev); 126 done: 127 return ret; 128 } 129 130 /* 131 * Do remaining PCIe setup, once dd is allocated, and save away 132 * fields required to re-initialize after a chip reset, or for 133 * various other purposes 134 */ 135 int qib_pcie_ddinit(struct qib_devdata *dd, struct pci_dev *pdev, 136 const struct pci_device_id *ent) 137 { 138 unsigned long len; 139 resource_size_t addr; 140 141 dd->pcidev = pdev; 142 pci_set_drvdata(pdev, dd); 143 144 addr = pci_resource_start(pdev, 0); 145 len = pci_resource_len(pdev, 0); 146 147 #if defined(__powerpc__) 148 /* There isn't a generic way to specify writethrough mappings */ 149 dd->kregbase = __ioremap(addr, len, _PAGE_NO_CACHE | _PAGE_WRITETHRU); 150 #else 151 dd->kregbase = ioremap_nocache(addr, len); 152 #endif 153 154 if (!dd->kregbase) 155 return -ENOMEM; 156 157 dd->kregend = (u64 __iomem *)((void __iomem *) dd->kregbase + len); 158 dd->physaddr = addr; /* used for io_remap, etc. */ 159 160 /* 161 * Save BARs to rewrite after device reset. Save all 64 bits of 162 * BAR, just in case. 163 */ 164 dd->pcibar0 = addr; 165 dd->pcibar1 = addr >> 32; 166 dd->deviceid = ent->device; /* save for later use */ 167 dd->vendorid = ent->vendor; 168 169 return 0; 170 } 171 172 /* 173 * Do PCIe cleanup, after chip-specific cleanup, etc. Just prior 174 * to releasing the dd memory. 175 * void because none of the core pcie cleanup returns are void 176 */ 177 void qib_pcie_ddcleanup(struct qib_devdata *dd) 178 { 179 u64 __iomem *base = (void __iomem *) dd->kregbase; 180 181 dd->kregbase = NULL; 182 iounmap(base); 183 if (dd->piobase) 184 iounmap(dd->piobase); 185 if (dd->userbase) 186 iounmap(dd->userbase); 187 if (dd->piovl15base) 188 iounmap(dd->piovl15base); 189 190 pci_disable_device(dd->pcidev); 191 pci_release_regions(dd->pcidev); 192 193 pci_set_drvdata(dd->pcidev, NULL); 194 } 195 196 static void qib_msix_setup(struct qib_devdata *dd, int pos, u32 *msixcnt, 197 struct qib_msix_entry *qib_msix_entry) 198 { 199 int ret; 200 u32 tabsize = 0; 201 u16 msix_flags; 202 struct msix_entry *msix_entry; 203 int i; 204 205 /* We can't pass qib_msix_entry array to qib_msix_setup 206 * so use a dummy msix_entry array and copy the allocated 207 * irq back to the qib_msix_entry array. */ 208 msix_entry = kmalloc(*msixcnt * sizeof(*msix_entry), GFP_KERNEL); 209 if (!msix_entry) { 210 ret = -ENOMEM; 211 goto do_intx; 212 } 213 for (i = 0; i < *msixcnt; i++) 214 msix_entry[i] = qib_msix_entry[i].msix; 215 216 pci_read_config_word(dd->pcidev, pos + PCI_MSIX_FLAGS, &msix_flags); 217 tabsize = 1 + (msix_flags & PCI_MSIX_FLAGS_QSIZE); 218 if (tabsize > *msixcnt) 219 tabsize = *msixcnt; 220 ret = pci_enable_msix(dd->pcidev, msix_entry, tabsize); 221 if (ret > 0) { 222 tabsize = ret; 223 ret = pci_enable_msix(dd->pcidev, msix_entry, tabsize); 224 } 225 do_intx: 226 if (ret) { 227 qib_dev_err(dd, 228 "pci_enable_msix %d vectors failed: %d, falling back to INTx\n", 229 tabsize, ret); 230 tabsize = 0; 231 } 232 for (i = 0; i < tabsize; i++) 233 qib_msix_entry[i].msix = msix_entry[i]; 234 kfree(msix_entry); 235 *msixcnt = tabsize; 236 237 if (ret) 238 qib_enable_intx(dd->pcidev); 239 240 } 241 242 /** 243 * We save the msi lo and hi values, so we can restore them after 244 * chip reset (the kernel PCI infrastructure doesn't yet handle that 245 * correctly. 246 */ 247 static int qib_msi_setup(struct qib_devdata *dd, int pos) 248 { 249 struct pci_dev *pdev = dd->pcidev; 250 u16 control; 251 int ret; 252 253 ret = pci_enable_msi(pdev); 254 if (ret) 255 qib_dev_err(dd, 256 "pci_enable_msi failed: %d, interrupts may not work\n", 257 ret); 258 /* continue even if it fails, we may still be OK... */ 259 260 pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_LO, 261 &dd->msi_lo); 262 pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_HI, 263 &dd->msi_hi); 264 pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &control); 265 /* now save the data (vector) info */ 266 pci_read_config_word(pdev, pos + ((control & PCI_MSI_FLAGS_64BIT) 267 ? 12 : 8), 268 &dd->msi_data); 269 return ret; 270 } 271 272 int qib_pcie_params(struct qib_devdata *dd, u32 minw, u32 *nent, 273 struct qib_msix_entry *entry) 274 { 275 u16 linkstat, speed; 276 int pos = 0, ret = 1; 277 278 if (!pci_is_pcie(dd->pcidev)) { 279 qib_dev_err(dd, "Can't find PCI Express capability!\n"); 280 /* set up something... */ 281 dd->lbus_width = 1; 282 dd->lbus_speed = 2500; /* Gen1, 2.5GHz */ 283 goto bail; 284 } 285 286 pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSIX); 287 if (nent && *nent && pos) { 288 qib_msix_setup(dd, pos, nent, entry); 289 ret = 0; /* did it, either MSIx or INTx */ 290 } else { 291 pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI); 292 if (pos) 293 ret = qib_msi_setup(dd, pos); 294 else 295 qib_dev_err(dd, "No PCI MSI or MSIx capability!\n"); 296 } 297 if (!pos) 298 qib_enable_intx(dd->pcidev); 299 300 pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKSTA, &linkstat); 301 /* 302 * speed is bits 0-3, linkwidth is bits 4-8 303 * no defines for them in headers 304 */ 305 speed = linkstat & 0xf; 306 linkstat >>= 4; 307 linkstat &= 0x1f; 308 dd->lbus_width = linkstat; 309 310 switch (speed) { 311 case 1: 312 dd->lbus_speed = 2500; /* Gen1, 2.5GHz */ 313 break; 314 case 2: 315 dd->lbus_speed = 5000; /* Gen1, 5GHz */ 316 break; 317 default: /* not defined, assume gen1 */ 318 dd->lbus_speed = 2500; 319 break; 320 } 321 322 /* 323 * Check against expected pcie width and complain if "wrong" 324 * on first initialization, not afterwards (i.e., reset). 325 */ 326 if (minw && linkstat < minw) 327 qib_dev_err(dd, 328 "PCIe width %u (x%u HCA), performance reduced\n", 329 linkstat, minw); 330 331 qib_tune_pcie_caps(dd); 332 333 qib_tune_pcie_coalesce(dd); 334 335 bail: 336 /* fill in string, even on errors */ 337 snprintf(dd->lbus_info, sizeof(dd->lbus_info), 338 "PCIe,%uMHz,x%u\n", dd->lbus_speed, dd->lbus_width); 339 return ret; 340 } 341 342 /* 343 * Setup pcie interrupt stuff again after a reset. I'd like to just call 344 * pci_enable_msi() again for msi, but when I do that, 345 * the MSI enable bit doesn't get set in the command word, and 346 * we switch to to a different interrupt vector, which is confusing, 347 * so I instead just do it all inline. Perhaps somehow can tie this 348 * into the PCIe hotplug support at some point 349 */ 350 int qib_reinit_intr(struct qib_devdata *dd) 351 { 352 int pos; 353 u16 control; 354 int ret = 0; 355 356 /* If we aren't using MSI, don't restore it */ 357 if (!dd->msi_lo) 358 goto bail; 359 360 pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI); 361 if (!pos) { 362 qib_dev_err(dd, 363 "Can't find MSI capability, can't restore MSI settings\n"); 364 ret = 0; 365 /* nothing special for MSIx, just MSI */ 366 goto bail; 367 } 368 pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO, 369 dd->msi_lo); 370 pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI, 371 dd->msi_hi); 372 pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, &control); 373 if (!(control & PCI_MSI_FLAGS_ENABLE)) { 374 control |= PCI_MSI_FLAGS_ENABLE; 375 pci_write_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, 376 control); 377 } 378 /* now rewrite the data (vector) info */ 379 pci_write_config_word(dd->pcidev, pos + 380 ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8), 381 dd->msi_data); 382 ret = 1; 383 bail: 384 if (!ret && (dd->flags & QIB_HAS_INTX)) { 385 qib_enable_intx(dd->pcidev); 386 ret = 1; 387 } 388 389 /* and now set the pci master bit again */ 390 pci_set_master(dd->pcidev); 391 392 return ret; 393 } 394 395 /* 396 * Disable msi interrupt if enabled, and clear msi_lo. 397 * This is used primarily for the fallback to INTx, but 398 * is also used in reinit after reset, and during cleanup. 399 */ 400 void qib_nomsi(struct qib_devdata *dd) 401 { 402 dd->msi_lo = 0; 403 pci_disable_msi(dd->pcidev); 404 } 405 406 /* 407 * Same as qib_nosmi, but for MSIx. 408 */ 409 void qib_nomsix(struct qib_devdata *dd) 410 { 411 pci_disable_msix(dd->pcidev); 412 } 413 414 /* 415 * Similar to pci_intx(pdev, 1), except that we make sure 416 * msi(x) is off. 417 */ 418 void qib_enable_intx(struct pci_dev *pdev) 419 { 420 u16 cw, new; 421 int pos; 422 423 /* first, turn on INTx */ 424 pci_read_config_word(pdev, PCI_COMMAND, &cw); 425 new = cw & ~PCI_COMMAND_INTX_DISABLE; 426 if (new != cw) 427 pci_write_config_word(pdev, PCI_COMMAND, new); 428 429 pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); 430 if (pos) { 431 /* then turn off MSI */ 432 pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &cw); 433 new = cw & ~PCI_MSI_FLAGS_ENABLE; 434 if (new != cw) 435 pci_write_config_word(pdev, pos + PCI_MSI_FLAGS, new); 436 } 437 pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX); 438 if (pos) { 439 /* then turn off MSIx */ 440 pci_read_config_word(pdev, pos + PCI_MSIX_FLAGS, &cw); 441 new = cw & ~PCI_MSIX_FLAGS_ENABLE; 442 if (new != cw) 443 pci_write_config_word(pdev, pos + PCI_MSIX_FLAGS, new); 444 } 445 } 446 447 /* 448 * These two routines are helper routines for the device reset code 449 * to move all the pcie code out of the chip-specific driver code. 450 */ 451 void qib_pcie_getcmd(struct qib_devdata *dd, u16 *cmd, u8 *iline, u8 *cline) 452 { 453 pci_read_config_word(dd->pcidev, PCI_COMMAND, cmd); 454 pci_read_config_byte(dd->pcidev, PCI_INTERRUPT_LINE, iline); 455 pci_read_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE, cline); 456 } 457 458 void qib_pcie_reenable(struct qib_devdata *dd, u16 cmd, u8 iline, u8 cline) 459 { 460 int r; 461 r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0, 462 dd->pcibar0); 463 if (r) 464 qib_dev_err(dd, "rewrite of BAR0 failed: %d\n", r); 465 r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1, 466 dd->pcibar1); 467 if (r) 468 qib_dev_err(dd, "rewrite of BAR1 failed: %d\n", r); 469 /* now re-enable memory access, and restore cosmetic settings */ 470 pci_write_config_word(dd->pcidev, PCI_COMMAND, cmd); 471 pci_write_config_byte(dd->pcidev, PCI_INTERRUPT_LINE, iline); 472 pci_write_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE, cline); 473 r = pci_enable_device(dd->pcidev); 474 if (r) 475 qib_dev_err(dd, 476 "pci_enable_device failed after reset: %d\n", r); 477 } 478 479 /* code to adjust PCIe capabilities. */ 480 481 static int fld2val(int wd, int mask) 482 { 483 int lsbmask; 484 485 if (!mask) 486 return 0; 487 wd &= mask; 488 lsbmask = mask ^ (mask & (mask - 1)); 489 wd /= lsbmask; 490 return wd; 491 } 492 493 static int val2fld(int wd, int mask) 494 { 495 int lsbmask; 496 497 if (!mask) 498 return 0; 499 lsbmask = mask ^ (mask & (mask - 1)); 500 wd *= lsbmask; 501 return wd; 502 } 503 504 static int qib_pcie_coalesce; 505 module_param_named(pcie_coalesce, qib_pcie_coalesce, int, S_IRUGO); 506 MODULE_PARM_DESC(pcie_coalesce, "tune PCIe colescing on some Intel chipsets"); 507 508 /* 509 * Enable PCIe completion and data coalescing, on Intel 5x00 and 7300 510 * chipsets. This is known to be unsafe for some revisions of some 511 * of these chipsets, with some BIOS settings, and enabling it on those 512 * systems may result in the system crashing, and/or data corruption. 513 */ 514 static int qib_tune_pcie_coalesce(struct qib_devdata *dd) 515 { 516 int r; 517 struct pci_dev *parent; 518 u16 devid; 519 u32 mask, bits, val; 520 521 if (!qib_pcie_coalesce) 522 return 0; 523 524 /* Find out supported and configured values for parent (root) */ 525 parent = dd->pcidev->bus->self; 526 if (parent->bus->parent) { 527 qib_devinfo(dd->pcidev, "Parent not root\n"); 528 return 1; 529 } 530 if (!pci_is_pcie(parent)) 531 return 1; 532 if (parent->vendor != 0x8086) 533 return 1; 534 535 /* 536 * - bit 12: Max_rdcmp_Imt_EN: need to set to 1 537 * - bit 11: COALESCE_FORCE: need to set to 0 538 * - bit 10: COALESCE_EN: need to set to 1 539 * (but limitations on some on some chipsets) 540 * 541 * On the Intel 5000, 5100, and 7300 chipsets, there is 542 * also: - bit 25:24: COALESCE_MODE, need to set to 0 543 */ 544 devid = parent->device; 545 if (devid >= 0x25e2 && devid <= 0x25fa) { 546 /* 5000 P/V/X/Z */ 547 if (parent->revision <= 0xb2) 548 bits = 1U << 10; 549 else 550 bits = 7U << 10; 551 mask = (3U << 24) | (7U << 10); 552 } else if (devid >= 0x65e2 && devid <= 0x65fa) { 553 /* 5100 */ 554 bits = 1U << 10; 555 mask = (3U << 24) | (7U << 10); 556 } else if (devid >= 0x4021 && devid <= 0x402e) { 557 /* 5400 */ 558 bits = 7U << 10; 559 mask = 7U << 10; 560 } else if (devid >= 0x3604 && devid <= 0x360a) { 561 /* 7300 */ 562 bits = 7U << 10; 563 mask = (3U << 24) | (7U << 10); 564 } else { 565 /* not one of the chipsets that we know about */ 566 return 1; 567 } 568 pci_read_config_dword(parent, 0x48, &val); 569 val &= ~mask; 570 val |= bits; 571 r = pci_write_config_dword(parent, 0x48, val); 572 return 0; 573 } 574 575 /* 576 * BIOS may not set PCIe bus-utilization parameters for best performance. 577 * Check and optionally adjust them to maximize our throughput. 578 */ 579 static int qib_pcie_caps; 580 module_param_named(pcie_caps, qib_pcie_caps, int, S_IRUGO); 581 MODULE_PARM_DESC(pcie_caps, "Max PCIe tuning: Payload (0..3), ReadReq (4..7)"); 582 583 static int qib_tune_pcie_caps(struct qib_devdata *dd) 584 { 585 int ret = 1; /* Assume the worst */ 586 struct pci_dev *parent; 587 u16 pcaps, pctl, ecaps, ectl; 588 int rc_sup, ep_sup; 589 int rc_cur, ep_cur; 590 591 /* Find out supported and configured values for parent (root) */ 592 parent = dd->pcidev->bus->self; 593 if (parent->bus->parent) { 594 qib_devinfo(dd->pcidev, "Parent not root\n"); 595 goto bail; 596 } 597 598 if (!pci_is_pcie(parent) || !pci_is_pcie(dd->pcidev)) 599 goto bail; 600 pcie_capability_read_word(parent, PCI_EXP_DEVCAP, &pcaps); 601 pcie_capability_read_word(parent, PCI_EXP_DEVCTL, &pctl); 602 /* Find out supported and configured values for endpoint (us) */ 603 pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCAP, &ecaps); 604 pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL, &ectl); 605 606 ret = 0; 607 /* Find max payload supported by root, endpoint */ 608 rc_sup = fld2val(pcaps, PCI_EXP_DEVCAP_PAYLOAD); 609 ep_sup = fld2val(ecaps, PCI_EXP_DEVCAP_PAYLOAD); 610 if (rc_sup > ep_sup) 611 rc_sup = ep_sup; 612 613 rc_cur = fld2val(pctl, PCI_EXP_DEVCTL_PAYLOAD); 614 ep_cur = fld2val(ectl, PCI_EXP_DEVCTL_PAYLOAD); 615 616 /* If Supported greater than limit in module param, limit it */ 617 if (rc_sup > (qib_pcie_caps & 7)) 618 rc_sup = qib_pcie_caps & 7; 619 /* If less than (allowed, supported), bump root payload */ 620 if (rc_sup > rc_cur) { 621 rc_cur = rc_sup; 622 pctl = (pctl & ~PCI_EXP_DEVCTL_PAYLOAD) | 623 val2fld(rc_cur, PCI_EXP_DEVCTL_PAYLOAD); 624 pcie_capability_write_word(parent, PCI_EXP_DEVCTL, pctl); 625 } 626 /* If less than (allowed, supported), bump endpoint payload */ 627 if (rc_sup > ep_cur) { 628 ep_cur = rc_sup; 629 ectl = (ectl & ~PCI_EXP_DEVCTL_PAYLOAD) | 630 val2fld(ep_cur, PCI_EXP_DEVCTL_PAYLOAD); 631 pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL, ectl); 632 } 633 634 /* 635 * Now the Read Request size. 636 * No field for max supported, but PCIe spec limits it to 4096, 637 * which is code '5' (log2(4096) - 7) 638 */ 639 rc_sup = 5; 640 if (rc_sup > ((qib_pcie_caps >> 4) & 7)) 641 rc_sup = (qib_pcie_caps >> 4) & 7; 642 rc_cur = fld2val(pctl, PCI_EXP_DEVCTL_READRQ); 643 ep_cur = fld2val(ectl, PCI_EXP_DEVCTL_READRQ); 644 645 if (rc_sup > rc_cur) { 646 rc_cur = rc_sup; 647 pctl = (pctl & ~PCI_EXP_DEVCTL_READRQ) | 648 val2fld(rc_cur, PCI_EXP_DEVCTL_READRQ); 649 pcie_capability_write_word(parent, PCI_EXP_DEVCTL, pctl); 650 } 651 if (rc_sup > ep_cur) { 652 ep_cur = rc_sup; 653 ectl = (ectl & ~PCI_EXP_DEVCTL_READRQ) | 654 val2fld(ep_cur, PCI_EXP_DEVCTL_READRQ); 655 pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL, ectl); 656 } 657 bail: 658 return ret; 659 } 660 /* End of PCIe capability tuning */ 661 662 /* 663 * From here through qib_pci_err_handler definition is invoked via 664 * PCI error infrastructure, registered via pci 665 */ 666 static pci_ers_result_t 667 qib_pci_error_detected(struct pci_dev *pdev, pci_channel_state_t state) 668 { 669 struct qib_devdata *dd = pci_get_drvdata(pdev); 670 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED; 671 672 switch (state) { 673 case pci_channel_io_normal: 674 qib_devinfo(pdev, "State Normal, ignoring\n"); 675 break; 676 677 case pci_channel_io_frozen: 678 qib_devinfo(pdev, "State Frozen, requesting reset\n"); 679 pci_disable_device(pdev); 680 ret = PCI_ERS_RESULT_NEED_RESET; 681 break; 682 683 case pci_channel_io_perm_failure: 684 qib_devinfo(pdev, "State Permanent Failure, disabling\n"); 685 if (dd) { 686 /* no more register accesses! */ 687 dd->flags &= ~QIB_PRESENT; 688 qib_disable_after_error(dd); 689 } 690 /* else early, or other problem */ 691 ret = PCI_ERS_RESULT_DISCONNECT; 692 break; 693 694 default: /* shouldn't happen */ 695 qib_devinfo(pdev, "QIB PCI errors detected (state %d)\n", 696 state); 697 break; 698 } 699 return ret; 700 } 701 702 static pci_ers_result_t 703 qib_pci_mmio_enabled(struct pci_dev *pdev) 704 { 705 u64 words = 0U; 706 struct qib_devdata *dd = pci_get_drvdata(pdev); 707 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED; 708 709 if (dd && dd->pport) { 710 words = dd->f_portcntr(dd->pport, QIBPORTCNTR_WORDRCV); 711 if (words == ~0ULL) 712 ret = PCI_ERS_RESULT_NEED_RESET; 713 } 714 qib_devinfo(pdev, 715 "QIB mmio_enabled function called, read wordscntr %Lx, returning %d\n", 716 words, ret); 717 return ret; 718 } 719 720 static pci_ers_result_t 721 qib_pci_slot_reset(struct pci_dev *pdev) 722 { 723 qib_devinfo(pdev, "QIB slot_reset function called, ignored\n"); 724 return PCI_ERS_RESULT_CAN_RECOVER; 725 } 726 727 static pci_ers_result_t 728 qib_pci_link_reset(struct pci_dev *pdev) 729 { 730 qib_devinfo(pdev, "QIB link_reset function called, ignored\n"); 731 return PCI_ERS_RESULT_CAN_RECOVER; 732 } 733 734 static void 735 qib_pci_resume(struct pci_dev *pdev) 736 { 737 struct qib_devdata *dd = pci_get_drvdata(pdev); 738 qib_devinfo(pdev, "QIB resume function called\n"); 739 pci_cleanup_aer_uncorrect_error_status(pdev); 740 /* 741 * Running jobs will fail, since it's asynchronous 742 * unlike sysfs-requested reset. Better than 743 * doing nothing. 744 */ 745 qib_init(dd, 1); /* same as re-init after reset */ 746 } 747 748 const struct pci_error_handlers qib_pci_err_handler = { 749 .error_detected = qib_pci_error_detected, 750 .mmio_enabled = qib_pci_mmio_enabled, 751 .link_reset = qib_pci_link_reset, 752 .slot_reset = qib_pci_slot_reset, 753 .resume = qib_pci_resume, 754 }; 755