1 // SPDX-License-Identifier: GPL-2.0 or BSD-3-Clause 2 /* 3 * Copyright(c) 2015 - 2019 Intel Corporation. 4 */ 5 6 #include <linux/bitfield.h> 7 #include <linux/pci.h> 8 #include <linux/io.h> 9 #include <linux/delay.h> 10 #include <linux/vmalloc.h> 11 #include <linux/module.h> 12 13 #include "hfi.h" 14 #include "chip_registers.h" 15 #include "aspm.h" 16 17 /* 18 * This file contains PCIe utility routines. 19 */ 20 21 /* 22 * Do all the common PCIe setup and initialization. 23 */ 24 int hfi1_pcie_init(struct hfi1_devdata *dd) 25 { 26 int ret; 27 struct pci_dev *pdev = dd->pcidev; 28 29 ret = pci_enable_device(pdev); 30 if (ret) { 31 /* 32 * This can happen (in theory) iff: 33 * We did a chip reset, and then failed to reprogram the 34 * BAR, or the chip reset due to an internal error. We then 35 * unloaded the driver and reloaded it. 36 * 37 * Both reset cases set the BAR back to initial state. For 38 * the latter case, the AER sticky error bit at offset 0x718 39 * should be set, but the Linux kernel doesn't yet know 40 * about that, it appears. If the original BAR was retained 41 * in the kernel data structures, this may be OK. 42 */ 43 dd_dev_err(dd, "pci enable failed: error %d\n", -ret); 44 return ret; 45 } 46 47 ret = pci_request_regions(pdev, DRIVER_NAME); 48 if (ret) { 49 dd_dev_err(dd, "pci_request_regions fails: err %d\n", -ret); 50 goto bail; 51 } 52 53 ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); 54 if (ret) { 55 /* 56 * If the 64 bit setup fails, try 32 bit. Some systems 57 * do not setup 64 bit maps on systems with 2GB or less 58 * memory installed. 59 */ 60 ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); 61 if (ret) { 62 dd_dev_err(dd, "Unable to set DMA mask: %d\n", ret); 63 goto bail; 64 } 65 } 66 67 pci_set_master(pdev); 68 return 0; 69 70 bail: 71 hfi1_pcie_cleanup(pdev); 72 return ret; 73 } 74 75 /* 76 * Clean what was done in hfi1_pcie_init() 77 */ 78 void hfi1_pcie_cleanup(struct pci_dev *pdev) 79 { 80 pci_disable_device(pdev); 81 /* 82 * Release regions should be called after the disable. OK to 83 * call if request regions has not been called or failed. 84 */ 85 pci_release_regions(pdev); 86 } 87 88 /* 89 * Do remaining PCIe setup, once dd is allocated, and save away 90 * fields required to re-initialize after a chip reset, or for 91 * various other purposes 92 */ 93 int hfi1_pcie_ddinit(struct hfi1_devdata *dd, struct pci_dev *pdev) 94 { 95 unsigned long len; 96 resource_size_t addr; 97 int ret = 0; 98 u32 rcv_array_count; 99 100 addr = pci_resource_start(pdev, 0); 101 len = pci_resource_len(pdev, 0); 102 103 /* 104 * The TXE PIO buffers are at the tail end of the chip space. 105 * Cut them off and map them separately. 106 */ 107 108 /* sanity check vs expectations */ 109 if (len != TXE_PIO_SEND + TXE_PIO_SIZE) { 110 dd_dev_err(dd, "chip PIO range does not match\n"); 111 return -EINVAL; 112 } 113 114 dd->kregbase1 = ioremap(addr, RCV_ARRAY); 115 if (!dd->kregbase1) { 116 dd_dev_err(dd, "UC mapping of kregbase1 failed\n"); 117 return -ENOMEM; 118 } 119 dd_dev_info(dd, "UC base1: %p for %x\n", dd->kregbase1, RCV_ARRAY); 120 121 /* verify that reads actually work, save revision for reset check */ 122 dd->revision = readq(dd->kregbase1 + CCE_REVISION); 123 if (dd->revision == ~(u64)0) { 124 dd_dev_err(dd, "Cannot read chip CSRs\n"); 125 goto nomem; 126 } 127 128 rcv_array_count = readq(dd->kregbase1 + RCV_ARRAY_CNT); 129 dd_dev_info(dd, "RcvArray count: %u\n", rcv_array_count); 130 dd->base2_start = RCV_ARRAY + rcv_array_count * 8; 131 132 dd->kregbase2 = ioremap( 133 addr + dd->base2_start, 134 TXE_PIO_SEND - dd->base2_start); 135 if (!dd->kregbase2) { 136 dd_dev_err(dd, "UC mapping of kregbase2 failed\n"); 137 goto nomem; 138 } 139 dd_dev_info(dd, "UC base2: %p for %x\n", dd->kregbase2, 140 TXE_PIO_SEND - dd->base2_start); 141 142 dd->piobase = ioremap_wc(addr + TXE_PIO_SEND, TXE_PIO_SIZE); 143 if (!dd->piobase) { 144 dd_dev_err(dd, "WC mapping of send buffers failed\n"); 145 goto nomem; 146 } 147 dd_dev_info(dd, "WC piobase: %p for %x\n", dd->piobase, TXE_PIO_SIZE); 148 149 dd->physaddr = addr; /* used for io_remap, etc. */ 150 151 /* 152 * Map the chip's RcvArray as write-combining to allow us 153 * to write an entire cacheline worth of entries in one shot. 154 */ 155 dd->rcvarray_wc = ioremap_wc(addr + RCV_ARRAY, 156 rcv_array_count * 8); 157 if (!dd->rcvarray_wc) { 158 dd_dev_err(dd, "WC mapping of receive array failed\n"); 159 goto nomem; 160 } 161 dd_dev_info(dd, "WC RcvArray: %p for %x\n", 162 dd->rcvarray_wc, rcv_array_count * 8); 163 164 dd->flags |= HFI1_PRESENT; /* chip.c CSR routines now work */ 165 return 0; 166 nomem: 167 ret = -ENOMEM; 168 hfi1_pcie_ddcleanup(dd); 169 return ret; 170 } 171 172 /* 173 * Do PCIe cleanup related to dd, after chip-specific cleanup, etc. Just prior 174 * to releasing the dd memory. 175 * Void because all of the core pcie cleanup functions are void. 176 */ 177 void hfi1_pcie_ddcleanup(struct hfi1_devdata *dd) 178 { 179 dd->flags &= ~HFI1_PRESENT; 180 if (dd->kregbase1) 181 iounmap(dd->kregbase1); 182 dd->kregbase1 = NULL; 183 if (dd->kregbase2) 184 iounmap(dd->kregbase2); 185 dd->kregbase2 = NULL; 186 if (dd->rcvarray_wc) 187 iounmap(dd->rcvarray_wc); 188 dd->rcvarray_wc = NULL; 189 if (dd->piobase) 190 iounmap(dd->piobase); 191 dd->piobase = NULL; 192 } 193 194 /* return the PCIe link speed from the given link status */ 195 static u32 extract_speed(u16 linkstat) 196 { 197 u32 speed; 198 199 switch (linkstat & PCI_EXP_LNKSTA_CLS) { 200 default: /* not defined, assume Gen1 */ 201 case PCI_EXP_LNKSTA_CLS_2_5GB: 202 speed = 2500; /* Gen 1, 2.5GHz */ 203 break; 204 case PCI_EXP_LNKSTA_CLS_5_0GB: 205 speed = 5000; /* Gen 2, 5GHz */ 206 break; 207 case PCI_EXP_LNKSTA_CLS_8_0GB: 208 speed = 8000; /* Gen 3, 8GHz */ 209 break; 210 } 211 return speed; 212 } 213 214 /* read the link status and set dd->{lbus_width,lbus_speed,lbus_info} */ 215 static void update_lbus_info(struct hfi1_devdata *dd) 216 { 217 u16 linkstat; 218 int ret; 219 220 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKSTA, &linkstat); 221 if (ret) { 222 dd_dev_err(dd, "Unable to read from PCI config\n"); 223 return; 224 } 225 226 dd->lbus_width = FIELD_GET(PCI_EXP_LNKSTA_NLW, linkstat); 227 dd->lbus_speed = extract_speed(linkstat); 228 snprintf(dd->lbus_info, sizeof(dd->lbus_info), 229 "PCIe,%uMHz,x%u", dd->lbus_speed, dd->lbus_width); 230 } 231 232 /* 233 * Read in the current PCIe link width and speed. Find if the link is 234 * Gen3 capable. 235 */ 236 int pcie_speeds(struct hfi1_devdata *dd) 237 { 238 u32 linkcap; 239 struct pci_dev *parent = dd->pcidev->bus->self; 240 int ret; 241 242 if (!pci_is_pcie(dd->pcidev)) { 243 dd_dev_err(dd, "Can't find PCI Express capability!\n"); 244 return -EINVAL; 245 } 246 247 /* find if our max speed is Gen3 and parent supports Gen3 speeds */ 248 dd->link_gen3_capable = 1; 249 250 ret = pcie_capability_read_dword(dd->pcidev, PCI_EXP_LNKCAP, &linkcap); 251 if (ret) { 252 dd_dev_err(dd, "Unable to read from PCI config\n"); 253 return pcibios_err_to_errno(ret); 254 } 255 256 if ((linkcap & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_8_0GB) { 257 dd_dev_info(dd, 258 "This HFI is not Gen3 capable, max speed 0x%x, need 0x3\n", 259 linkcap & PCI_EXP_LNKCAP_SLS); 260 dd->link_gen3_capable = 0; 261 } 262 263 /* 264 * bus->max_bus_speed is set from the bridge's linkcap Max Link Speed 265 */ 266 if (parent && 267 (dd->pcidev->bus->max_bus_speed == PCIE_SPEED_2_5GT || 268 dd->pcidev->bus->max_bus_speed == PCIE_SPEED_5_0GT)) { 269 dd_dev_info(dd, "Parent PCIe bridge does not support Gen3\n"); 270 dd->link_gen3_capable = 0; 271 } 272 273 /* obtain the link width and current speed */ 274 update_lbus_info(dd); 275 276 dd_dev_info(dd, "%s\n", dd->lbus_info); 277 278 return 0; 279 } 280 281 /* 282 * Restore command and BARs after a reset has wiped them out 283 * 284 * Returns 0 on success, otherwise a negative error value 285 */ 286 int restore_pci_variables(struct hfi1_devdata *dd) 287 { 288 int ret; 289 290 ret = pci_write_config_word(dd->pcidev, PCI_COMMAND, dd->pci_command); 291 if (ret) 292 goto error; 293 294 ret = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0, 295 dd->pcibar0); 296 if (ret) 297 goto error; 298 299 ret = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1, 300 dd->pcibar1); 301 if (ret) 302 goto error; 303 304 ret = pci_write_config_dword(dd->pcidev, PCI_ROM_ADDRESS, dd->pci_rom); 305 if (ret) 306 goto error; 307 308 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL, 309 dd->pcie_devctl); 310 if (ret) 311 goto error; 312 313 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL, 314 dd->pcie_lnkctl); 315 if (ret) 316 goto error; 317 318 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL2, 319 dd->pcie_devctl2); 320 if (ret) 321 goto error; 322 323 ret = pci_write_config_dword(dd->pcidev, PCI_CFG_MSIX0, dd->pci_msix0); 324 if (ret) 325 goto error; 326 327 if (pci_find_ext_capability(dd->pcidev, PCI_EXT_CAP_ID_TPH)) { 328 ret = pci_write_config_dword(dd->pcidev, PCIE_CFG_TPH2, 329 dd->pci_tph2); 330 if (ret) 331 goto error; 332 } 333 return 0; 334 335 error: 336 dd_dev_err(dd, "Unable to write to PCI config\n"); 337 return pcibios_err_to_errno(ret); 338 } 339 340 /* 341 * Save BARs and command to rewrite after device reset 342 * 343 * Returns 0 on success, otherwise a negative error value 344 */ 345 int save_pci_variables(struct hfi1_devdata *dd) 346 { 347 int ret; 348 349 ret = pci_read_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0, 350 &dd->pcibar0); 351 if (ret) 352 goto error; 353 354 ret = pci_read_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1, 355 &dd->pcibar1); 356 if (ret) 357 goto error; 358 359 ret = pci_read_config_dword(dd->pcidev, PCI_ROM_ADDRESS, &dd->pci_rom); 360 if (ret) 361 goto error; 362 363 ret = pci_read_config_word(dd->pcidev, PCI_COMMAND, &dd->pci_command); 364 if (ret) 365 goto error; 366 367 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL, 368 &dd->pcie_devctl); 369 if (ret) 370 goto error; 371 372 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL, 373 &dd->pcie_lnkctl); 374 if (ret) 375 goto error; 376 377 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL2, 378 &dd->pcie_devctl2); 379 if (ret) 380 goto error; 381 382 ret = pci_read_config_dword(dd->pcidev, PCI_CFG_MSIX0, &dd->pci_msix0); 383 if (ret) 384 goto error; 385 386 if (pci_find_ext_capability(dd->pcidev, PCI_EXT_CAP_ID_TPH)) { 387 ret = pci_read_config_dword(dd->pcidev, PCIE_CFG_TPH2, 388 &dd->pci_tph2); 389 if (ret) 390 goto error; 391 } 392 return 0; 393 394 error: 395 dd_dev_err(dd, "Unable to read from PCI config\n"); 396 return pcibios_err_to_errno(ret); 397 } 398 399 /* 400 * BIOS may not set PCIe bus-utilization parameters for best performance. 401 * Check and optionally adjust them to maximize our throughput. 402 */ 403 static int hfi1_pcie_caps; 404 module_param_named(pcie_caps, hfi1_pcie_caps, int, 0444); 405 MODULE_PARM_DESC(pcie_caps, "Max PCIe tuning: Payload (0..3), ReadReq (4..7)"); 406 407 /** 408 * tune_pcie_caps() - Code to adjust PCIe capabilities. 409 * @dd: Valid device data structure 410 * 411 */ 412 void tune_pcie_caps(struct hfi1_devdata *dd) 413 { 414 struct pci_dev *parent; 415 u16 rc_mpss, rc_mps, ep_mpss, ep_mps; 416 u16 rc_mrrs, ep_mrrs, max_mrrs, ectl; 417 int ret; 418 419 /* 420 * Turn on extended tags in DevCtl in case the BIOS has turned it off 421 * to improve WFR SDMA bandwidth 422 */ 423 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL, &ectl); 424 if ((!ret) && !(ectl & PCI_EXP_DEVCTL_EXT_TAG)) { 425 dd_dev_info(dd, "Enabling PCIe extended tags\n"); 426 ectl |= PCI_EXP_DEVCTL_EXT_TAG; 427 ret = pcie_capability_write_word(dd->pcidev, 428 PCI_EXP_DEVCTL, ectl); 429 if (ret) 430 dd_dev_info(dd, "Unable to write to PCI config\n"); 431 } 432 /* Find out supported and configured values for parent (root) */ 433 parent = dd->pcidev->bus->self; 434 /* 435 * The driver cannot perform the tuning if it does not have 436 * access to the upstream component. 437 */ 438 if (!parent) { 439 dd_dev_info(dd, "Parent not found\n"); 440 return; 441 } 442 if (!pci_is_root_bus(parent->bus)) { 443 dd_dev_info(dd, "Parent not root\n"); 444 return; 445 } 446 if (!pci_is_pcie(parent)) { 447 dd_dev_info(dd, "Parent is not PCI Express capable\n"); 448 return; 449 } 450 if (!pci_is_pcie(dd->pcidev)) { 451 dd_dev_info(dd, "PCI device is not PCI Express capable\n"); 452 return; 453 } 454 rc_mpss = parent->pcie_mpss; 455 rc_mps = ffs(pcie_get_mps(parent)) - 8; 456 /* Find out supported and configured values for endpoint (us) */ 457 ep_mpss = dd->pcidev->pcie_mpss; 458 ep_mps = ffs(pcie_get_mps(dd->pcidev)) - 8; 459 460 /* Find max payload supported by root, endpoint */ 461 if (rc_mpss > ep_mpss) 462 rc_mpss = ep_mpss; 463 464 /* If Supported greater than limit in module param, limit it */ 465 if (rc_mpss > (hfi1_pcie_caps & 7)) 466 rc_mpss = hfi1_pcie_caps & 7; 467 /* If less than (allowed, supported), bump root payload */ 468 if (rc_mpss > rc_mps) { 469 rc_mps = rc_mpss; 470 pcie_set_mps(parent, 128 << rc_mps); 471 } 472 /* If less than (allowed, supported), bump endpoint payload */ 473 if (rc_mpss > ep_mps) { 474 ep_mps = rc_mpss; 475 pcie_set_mps(dd->pcidev, 128 << ep_mps); 476 } 477 478 /* 479 * Now the Read Request size. 480 * No field for max supported, but PCIe spec limits it to 4096, 481 * which is code '5' (log2(4096) - 7) 482 */ 483 max_mrrs = 5; 484 if (max_mrrs > ((hfi1_pcie_caps >> 4) & 7)) 485 max_mrrs = (hfi1_pcie_caps >> 4) & 7; 486 487 max_mrrs = 128 << max_mrrs; 488 rc_mrrs = pcie_get_readrq(parent); 489 ep_mrrs = pcie_get_readrq(dd->pcidev); 490 491 if (max_mrrs > rc_mrrs) { 492 rc_mrrs = max_mrrs; 493 pcie_set_readrq(parent, rc_mrrs); 494 } 495 if (max_mrrs > ep_mrrs) { 496 ep_mrrs = max_mrrs; 497 pcie_set_readrq(dd->pcidev, ep_mrrs); 498 } 499 } 500 501 /* End of PCIe capability tuning */ 502 503 /* 504 * From here through hfi1_pci_err_handler definition is invoked via 505 * PCI error infrastructure, registered via pci 506 */ 507 static pci_ers_result_t 508 pci_error_detected(struct pci_dev *pdev, pci_channel_state_t state) 509 { 510 struct hfi1_devdata *dd = pci_get_drvdata(pdev); 511 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED; 512 513 switch (state) { 514 case pci_channel_io_normal: 515 dd_dev_info(dd, "State Normal, ignoring\n"); 516 break; 517 518 case pci_channel_io_frozen: 519 dd_dev_info(dd, "State Frozen, requesting reset\n"); 520 pci_disable_device(pdev); 521 ret = PCI_ERS_RESULT_NEED_RESET; 522 break; 523 524 case pci_channel_io_perm_failure: 525 if (dd) { 526 dd_dev_info(dd, "State Permanent Failure, disabling\n"); 527 /* no more register accesses! */ 528 dd->flags &= ~HFI1_PRESENT; 529 hfi1_disable_after_error(dd); 530 } 531 /* else early, or other problem */ 532 ret = PCI_ERS_RESULT_DISCONNECT; 533 break; 534 535 default: /* shouldn't happen */ 536 dd_dev_info(dd, "HFI1 PCI errors detected (state %d)\n", 537 state); 538 break; 539 } 540 return ret; 541 } 542 543 static pci_ers_result_t 544 pci_mmio_enabled(struct pci_dev *pdev) 545 { 546 u64 words = 0U; 547 struct hfi1_devdata *dd = pci_get_drvdata(pdev); 548 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED; 549 550 if (dd && dd->pport) { 551 words = read_port_cntr(dd->pport, C_RX_WORDS, CNTR_INVALID_VL); 552 if (words == ~0ULL) 553 ret = PCI_ERS_RESULT_NEED_RESET; 554 dd_dev_info(dd, 555 "HFI1 mmio_enabled function called, read wordscntr %llx, returning %d\n", 556 words, ret); 557 } 558 return ret; 559 } 560 561 static pci_ers_result_t 562 pci_slot_reset(struct pci_dev *pdev) 563 { 564 struct hfi1_devdata *dd = pci_get_drvdata(pdev); 565 566 dd_dev_info(dd, "HFI1 slot_reset function called, ignored\n"); 567 return PCI_ERS_RESULT_CAN_RECOVER; 568 } 569 570 static void 571 pci_resume(struct pci_dev *pdev) 572 { 573 struct hfi1_devdata *dd = pci_get_drvdata(pdev); 574 575 dd_dev_info(dd, "HFI1 resume function called\n"); 576 /* 577 * Running jobs will fail, since it's asynchronous 578 * unlike sysfs-requested reset. Better than 579 * doing nothing. 580 */ 581 hfi1_init(dd, 1); /* same as re-init after reset */ 582 } 583 584 const struct pci_error_handlers hfi1_pci_err_handler = { 585 .error_detected = pci_error_detected, 586 .mmio_enabled = pci_mmio_enabled, 587 .slot_reset = pci_slot_reset, 588 .resume = pci_resume, 589 }; 590 591 /*============================================================================*/ 592 /* PCIe Gen3 support */ 593 594 /* 595 * This code is separated out because it is expected to be removed in the 596 * final shipping product. If not, then it will be revisited and items 597 * will be moved to more standard locations. 598 */ 599 600 /* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_STS field values */ 601 #define DL_STATUS_HFI0 0x1 /* hfi0 firmware download complete */ 602 #define DL_STATUS_HFI1 0x2 /* hfi1 firmware download complete */ 603 #define DL_STATUS_BOTH 0x3 /* hfi0 and hfi1 firmware download complete */ 604 605 /* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_ERR field values */ 606 #define DL_ERR_NONE 0x0 /* no error */ 607 #define DL_ERR_SWAP_PARITY 0x1 /* parity error in SerDes interrupt */ 608 /* or response data */ 609 #define DL_ERR_DISABLED 0x2 /* hfi disabled */ 610 #define DL_ERR_SECURITY 0x3 /* security check failed */ 611 #define DL_ERR_SBUS 0x4 /* SBus status error */ 612 #define DL_ERR_XFR_PARITY 0x5 /* parity error during ROM transfer*/ 613 614 /* gasket block secondary bus reset delay */ 615 #define SBR_DELAY_US 200000 /* 200ms */ 616 617 static uint pcie_target = 3; 618 module_param(pcie_target, uint, S_IRUGO); 619 MODULE_PARM_DESC(pcie_target, "PCIe target speed (0 skip, 1-3 Gen1-3)"); 620 621 static uint pcie_force; 622 module_param(pcie_force, uint, S_IRUGO); 623 MODULE_PARM_DESC(pcie_force, "Force driver to do a PCIe firmware download even if already at target speed"); 624 625 static uint pcie_retry = 5; 626 module_param(pcie_retry, uint, S_IRUGO); 627 MODULE_PARM_DESC(pcie_retry, "Driver will try this many times to reach requested speed"); 628 629 #define UNSET_PSET 255 630 #define DEFAULT_DISCRETE_PSET 2 /* discrete HFI */ 631 #define DEFAULT_MCP_PSET 6 /* MCP HFI */ 632 static uint pcie_pset = UNSET_PSET; 633 module_param(pcie_pset, uint, S_IRUGO); 634 MODULE_PARM_DESC(pcie_pset, "PCIe Eq Pset value to use, range is 0-10"); 635 636 static uint pcie_ctle = 3; /* discrete on, integrated on */ 637 module_param(pcie_ctle, uint, S_IRUGO); 638 MODULE_PARM_DESC(pcie_ctle, "PCIe static CTLE mode, bit 0 - discrete on/off, bit 1 - integrated on/off"); 639 640 /* equalization columns */ 641 #define PREC 0 642 #define ATTN 1 643 #define POST 2 644 645 /* discrete silicon preliminary equalization values */ 646 static const u8 discrete_preliminary_eq[11][3] = { 647 /* prec attn post */ 648 { 0x00, 0x00, 0x12 }, /* p0 */ 649 { 0x00, 0x00, 0x0c }, /* p1 */ 650 { 0x00, 0x00, 0x0f }, /* p2 */ 651 { 0x00, 0x00, 0x09 }, /* p3 */ 652 { 0x00, 0x00, 0x00 }, /* p4 */ 653 { 0x06, 0x00, 0x00 }, /* p5 */ 654 { 0x09, 0x00, 0x00 }, /* p6 */ 655 { 0x06, 0x00, 0x0f }, /* p7 */ 656 { 0x09, 0x00, 0x09 }, /* p8 */ 657 { 0x0c, 0x00, 0x00 }, /* p9 */ 658 { 0x00, 0x00, 0x18 }, /* p10 */ 659 }; 660 661 /* integrated silicon preliminary equalization values */ 662 static const u8 integrated_preliminary_eq[11][3] = { 663 /* prec attn post */ 664 { 0x00, 0x1e, 0x07 }, /* p0 */ 665 { 0x00, 0x1e, 0x05 }, /* p1 */ 666 { 0x00, 0x1e, 0x06 }, /* p2 */ 667 { 0x00, 0x1e, 0x04 }, /* p3 */ 668 { 0x00, 0x1e, 0x00 }, /* p4 */ 669 { 0x03, 0x1e, 0x00 }, /* p5 */ 670 { 0x04, 0x1e, 0x00 }, /* p6 */ 671 { 0x03, 0x1e, 0x06 }, /* p7 */ 672 { 0x03, 0x1e, 0x04 }, /* p8 */ 673 { 0x05, 0x1e, 0x00 }, /* p9 */ 674 { 0x00, 0x1e, 0x0a }, /* p10 */ 675 }; 676 677 static const u8 discrete_ctle_tunings[11][4] = { 678 /* DC LF HF BW */ 679 { 0x48, 0x0b, 0x04, 0x04 }, /* p0 */ 680 { 0x60, 0x05, 0x0f, 0x0a }, /* p1 */ 681 { 0x50, 0x09, 0x06, 0x06 }, /* p2 */ 682 { 0x68, 0x05, 0x0f, 0x0a }, /* p3 */ 683 { 0x80, 0x05, 0x0f, 0x0a }, /* p4 */ 684 { 0x70, 0x05, 0x0f, 0x0a }, /* p5 */ 685 { 0x68, 0x05, 0x0f, 0x0a }, /* p6 */ 686 { 0x38, 0x0f, 0x00, 0x00 }, /* p7 */ 687 { 0x48, 0x09, 0x06, 0x06 }, /* p8 */ 688 { 0x60, 0x05, 0x0f, 0x0a }, /* p9 */ 689 { 0x38, 0x0f, 0x00, 0x00 }, /* p10 */ 690 }; 691 692 static const u8 integrated_ctle_tunings[11][4] = { 693 /* DC LF HF BW */ 694 { 0x38, 0x0f, 0x00, 0x00 }, /* p0 */ 695 { 0x38, 0x0f, 0x00, 0x00 }, /* p1 */ 696 { 0x38, 0x0f, 0x00, 0x00 }, /* p2 */ 697 { 0x38, 0x0f, 0x00, 0x00 }, /* p3 */ 698 { 0x58, 0x0a, 0x05, 0x05 }, /* p4 */ 699 { 0x48, 0x0a, 0x05, 0x05 }, /* p5 */ 700 { 0x40, 0x0a, 0x05, 0x05 }, /* p6 */ 701 { 0x38, 0x0f, 0x00, 0x00 }, /* p7 */ 702 { 0x38, 0x0f, 0x00, 0x00 }, /* p8 */ 703 { 0x38, 0x09, 0x06, 0x06 }, /* p9 */ 704 { 0x38, 0x0e, 0x01, 0x01 }, /* p10 */ 705 }; 706 707 /* helper to format the value to write to hardware */ 708 #define eq_value(pre, curr, post) \ 709 ((((u32)(pre)) << \ 710 PCIE_CFG_REG_PL102_GEN3_EQ_PRE_CURSOR_PSET_SHIFT) \ 711 | (((u32)(curr)) << PCIE_CFG_REG_PL102_GEN3_EQ_CURSOR_PSET_SHIFT) \ 712 | (((u32)(post)) << \ 713 PCIE_CFG_REG_PL102_GEN3_EQ_POST_CURSOR_PSET_SHIFT)) 714 715 /* 716 * Load the given EQ preset table into the PCIe hardware. 717 */ 718 static int load_eq_table(struct hfi1_devdata *dd, const u8 eq[11][3], u8 fs, 719 u8 div) 720 { 721 struct pci_dev *pdev = dd->pcidev; 722 u32 hit_error = 0; 723 u32 violation; 724 u32 i; 725 u8 c_minus1, c0, c_plus1; 726 int ret; 727 728 for (i = 0; i < 11; i++) { 729 /* set index */ 730 pci_write_config_dword(pdev, PCIE_CFG_REG_PL103, i); 731 /* write the value */ 732 c_minus1 = eq[i][PREC] / div; 733 c0 = fs - (eq[i][PREC] / div) - (eq[i][POST] / div); 734 c_plus1 = eq[i][POST] / div; 735 pci_write_config_dword(pdev, PCIE_CFG_REG_PL102, 736 eq_value(c_minus1, c0, c_plus1)); 737 /* check if these coefficients violate EQ rules */ 738 ret = pci_read_config_dword(dd->pcidev, 739 PCIE_CFG_REG_PL105, &violation); 740 if (ret) { 741 dd_dev_err(dd, "Unable to read from PCI config\n"); 742 hit_error = 1; 743 break; 744 } 745 746 if (violation 747 & PCIE_CFG_REG_PL105_GEN3_EQ_VIOLATE_COEF_RULES_SMASK){ 748 if (hit_error == 0) { 749 dd_dev_err(dd, 750 "Gen3 EQ Table Coefficient rule violations\n"); 751 dd_dev_err(dd, " prec attn post\n"); 752 } 753 dd_dev_err(dd, " p%02d: %02x %02x %02x\n", 754 i, (u32)eq[i][0], (u32)eq[i][1], 755 (u32)eq[i][2]); 756 dd_dev_err(dd, " %02x %02x %02x\n", 757 (u32)c_minus1, (u32)c0, (u32)c_plus1); 758 hit_error = 1; 759 } 760 } 761 if (hit_error) 762 return -EINVAL; 763 return 0; 764 } 765 766 /* 767 * Steps to be done after the PCIe firmware is downloaded and 768 * before the SBR for the Pcie Gen3. 769 * The SBus resource is already being held. 770 */ 771 static void pcie_post_steps(struct hfi1_devdata *dd) 772 { 773 int i; 774 775 set_sbus_fast_mode(dd); 776 /* 777 * Write to the PCIe PCSes to set the G3_LOCKED_NEXT bits to 1. 778 * This avoids a spurious framing error that can otherwise be 779 * generated by the MAC layer. 780 * 781 * Use individual addresses since no broadcast is set up. 782 */ 783 for (i = 0; i < NUM_PCIE_SERDES; i++) { 784 sbus_request(dd, pcie_pcs_addrs[dd->hfi1_id][i], 785 0x03, WRITE_SBUS_RECEIVER, 0x00022132); 786 } 787 788 clear_sbus_fast_mode(dd); 789 } 790 791 /* 792 * Trigger a secondary bus reset (SBR) on ourselves using our parent. 793 * 794 * Based on pci_parent_bus_reset() which is not exported by the 795 * kernel core. 796 */ 797 static int trigger_sbr(struct hfi1_devdata *dd) 798 { 799 struct pci_dev *dev = dd->pcidev; 800 struct pci_dev *pdev; 801 802 /* need a parent */ 803 if (!dev->bus->self) { 804 dd_dev_err(dd, "%s: no parent device\n", __func__); 805 return -ENOTTY; 806 } 807 808 /* should not be anyone else on the bus */ 809 list_for_each_entry(pdev, &dev->bus->devices, bus_list) 810 if (pdev != dev) { 811 dd_dev_err(dd, 812 "%s: another device is on the same bus\n", 813 __func__); 814 return -ENOTTY; 815 } 816 817 /* 818 * This is an end around to do an SBR during probe time. A new API needs 819 * to be implemented to have cleaner interface but this fixes the 820 * current brokenness 821 */ 822 return pci_bridge_secondary_bus_reset(dev->bus->self); 823 } 824 825 /* 826 * Write the given gasket interrupt register. 827 */ 828 static void write_gasket_interrupt(struct hfi1_devdata *dd, int index, 829 u16 code, u16 data) 830 { 831 write_csr(dd, ASIC_PCIE_SD_INTRPT_LIST + (index * 8), 832 (((u64)code << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_CODE_SHIFT) | 833 ((u64)data << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_DATA_SHIFT))); 834 } 835 836 /* 837 * Tell the gasket logic how to react to the reset. 838 */ 839 static void arm_gasket_logic(struct hfi1_devdata *dd) 840 { 841 u64 reg; 842 843 reg = (((u64)1 << dd->hfi1_id) << 844 ASIC_PCIE_SD_HOST_CMD_INTRPT_CMD_SHIFT) | 845 ((u64)pcie_serdes_broadcast[dd->hfi1_id] << 846 ASIC_PCIE_SD_HOST_CMD_SBUS_RCVR_ADDR_SHIFT | 847 ASIC_PCIE_SD_HOST_CMD_SBR_MODE_SMASK | 848 ((u64)SBR_DELAY_US & ASIC_PCIE_SD_HOST_CMD_TIMER_MASK) << 849 ASIC_PCIE_SD_HOST_CMD_TIMER_SHIFT); 850 write_csr(dd, ASIC_PCIE_SD_HOST_CMD, reg); 851 /* read back to push the write */ 852 read_csr(dd, ASIC_PCIE_SD_HOST_CMD); 853 } 854 855 /* 856 * CCE_PCIE_CTRL long name helpers 857 * We redefine these shorter macros to use in the code while leaving 858 * chip_registers.h to be autogenerated from the hardware spec. 859 */ 860 #define LANE_BUNDLE_MASK CCE_PCIE_CTRL_PCIE_LANE_BUNDLE_MASK 861 #define LANE_BUNDLE_SHIFT CCE_PCIE_CTRL_PCIE_LANE_BUNDLE_SHIFT 862 #define LANE_DELAY_MASK CCE_PCIE_CTRL_PCIE_LANE_DELAY_MASK 863 #define LANE_DELAY_SHIFT CCE_PCIE_CTRL_PCIE_LANE_DELAY_SHIFT 864 #define MARGIN_OVERWRITE_ENABLE_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_OVERWRITE_ENABLE_SHIFT 865 #define MARGIN_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_SHIFT 866 #define MARGIN_G1_G2_OVERWRITE_MASK CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_OVERWRITE_ENABLE_MASK 867 #define MARGIN_G1_G2_OVERWRITE_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_OVERWRITE_ENABLE_SHIFT 868 #define MARGIN_GEN1_GEN2_MASK CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_MASK 869 #define MARGIN_GEN1_GEN2_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_SHIFT 870 871 /* 872 * Write xmt_margin for full-swing (WFR-B) or half-swing (WFR-C). 873 */ 874 static void write_xmt_margin(struct hfi1_devdata *dd, const char *fname) 875 { 876 u64 pcie_ctrl; 877 u64 xmt_margin; 878 u64 xmt_margin_oe; 879 u64 lane_delay; 880 u64 lane_bundle; 881 882 pcie_ctrl = read_csr(dd, CCE_PCIE_CTRL); 883 884 /* 885 * For Discrete, use full-swing. 886 * - PCIe TX defaults to full-swing. 887 * Leave this register as default. 888 * For Integrated, use half-swing 889 * - Copy xmt_margin and xmt_margin_oe 890 * from Gen1/Gen2 to Gen3. 891 */ 892 if (dd->pcidev->device == PCI_DEVICE_ID_INTEL1) { /* integrated */ 893 /* extract initial fields */ 894 xmt_margin = (pcie_ctrl >> MARGIN_GEN1_GEN2_SHIFT) 895 & MARGIN_GEN1_GEN2_MASK; 896 xmt_margin_oe = (pcie_ctrl >> MARGIN_G1_G2_OVERWRITE_SHIFT) 897 & MARGIN_G1_G2_OVERWRITE_MASK; 898 lane_delay = (pcie_ctrl >> LANE_DELAY_SHIFT) & LANE_DELAY_MASK; 899 lane_bundle = (pcie_ctrl >> LANE_BUNDLE_SHIFT) 900 & LANE_BUNDLE_MASK; 901 902 /* 903 * For A0, EFUSE values are not set. Override with the 904 * correct values. 905 */ 906 if (is_ax(dd)) { 907 /* 908 * xmt_margin and OverwiteEnabel should be the 909 * same for Gen1/Gen2 and Gen3 910 */ 911 xmt_margin = 0x5; 912 xmt_margin_oe = 0x1; 913 lane_delay = 0xF; /* Delay 240ns. */ 914 lane_bundle = 0x0; /* Set to 1 lane. */ 915 } 916 917 /* overwrite existing values */ 918 pcie_ctrl = (xmt_margin << MARGIN_GEN1_GEN2_SHIFT) 919 | (xmt_margin_oe << MARGIN_G1_G2_OVERWRITE_SHIFT) 920 | (xmt_margin << MARGIN_SHIFT) 921 | (xmt_margin_oe << MARGIN_OVERWRITE_ENABLE_SHIFT) 922 | (lane_delay << LANE_DELAY_SHIFT) 923 | (lane_bundle << LANE_BUNDLE_SHIFT); 924 925 write_csr(dd, CCE_PCIE_CTRL, pcie_ctrl); 926 } 927 928 dd_dev_dbg(dd, "%s: program XMT margin, CcePcieCtrl 0x%llx\n", 929 fname, pcie_ctrl); 930 } 931 932 /* 933 * Do all the steps needed to transition the PCIe link to Gen3 speed. 934 */ 935 int do_pcie_gen3_transition(struct hfi1_devdata *dd) 936 { 937 struct pci_dev *parent = dd->pcidev->bus->self; 938 u64 fw_ctrl; 939 u64 reg, therm; 940 u32 reg32, fs, lf; 941 u32 status, err; 942 int ret; 943 int do_retry, retry_count = 0; 944 int intnum = 0; 945 uint default_pset; 946 uint pset = pcie_pset; 947 u16 target_vector, target_speed; 948 u16 lnkctl2, vendor; 949 u8 div; 950 const u8 (*eq)[3]; 951 const u8 (*ctle_tunings)[4]; 952 uint static_ctle_mode; 953 int return_error = 0; 954 u32 target_width; 955 956 /* PCIe Gen3 is for the ASIC only */ 957 if (dd->icode != ICODE_RTL_SILICON) 958 return 0; 959 960 if (pcie_target == 1) { /* target Gen1 */ 961 target_vector = PCI_EXP_LNKCTL2_TLS_2_5GT; 962 target_speed = 2500; 963 } else if (pcie_target == 2) { /* target Gen2 */ 964 target_vector = PCI_EXP_LNKCTL2_TLS_5_0GT; 965 target_speed = 5000; 966 } else if (pcie_target == 3) { /* target Gen3 */ 967 target_vector = PCI_EXP_LNKCTL2_TLS_8_0GT; 968 target_speed = 8000; 969 } else { 970 /* off or invalid target - skip */ 971 dd_dev_info(dd, "%s: Skipping PCIe transition\n", __func__); 972 return 0; 973 } 974 975 /* if already at target speed, done (unless forced) */ 976 if (dd->lbus_speed == target_speed) { 977 dd_dev_info(dd, "%s: PCIe already at gen%d, %s\n", __func__, 978 pcie_target, 979 pcie_force ? "re-doing anyway" : "skipping"); 980 if (!pcie_force) 981 return 0; 982 } 983 984 /* 985 * The driver cannot do the transition if it has no access to the 986 * upstream component 987 */ 988 if (!parent) { 989 dd_dev_info(dd, "%s: No upstream, Can't do gen3 transition\n", 990 __func__); 991 return 0; 992 } 993 994 /* Previous Gen1/Gen2 bus width */ 995 target_width = dd->lbus_width; 996 997 /* 998 * Do the Gen3 transition. Steps are those of the PCIe Gen3 999 * recipe. 1000 */ 1001 1002 /* step 1: pcie link working in gen1/gen2 */ 1003 1004 /* step 2: if either side is not capable of Gen3, done */ 1005 if (pcie_target == 3 && !dd->link_gen3_capable) { 1006 dd_dev_err(dd, "The PCIe link is not Gen3 capable\n"); 1007 ret = -ENOSYS; 1008 goto done_no_mutex; 1009 } 1010 1011 /* hold the SBus resource across the firmware download and SBR */ 1012 ret = acquire_chip_resource(dd, CR_SBUS, SBUS_TIMEOUT); 1013 if (ret) { 1014 dd_dev_err(dd, "%s: unable to acquire SBus resource\n", 1015 __func__); 1016 return ret; 1017 } 1018 1019 /* make sure thermal polling is not causing interrupts */ 1020 therm = read_csr(dd, ASIC_CFG_THERM_POLL_EN); 1021 if (therm) { 1022 write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x0); 1023 msleep(100); 1024 dd_dev_info(dd, "%s: Disabled therm polling\n", 1025 __func__); 1026 } 1027 1028 retry: 1029 /* the SBus download will reset the spico for thermal */ 1030 1031 /* step 3: download SBus Master firmware */ 1032 /* step 4: download PCIe Gen3 SerDes firmware */ 1033 dd_dev_info(dd, "%s: downloading firmware\n", __func__); 1034 ret = load_pcie_firmware(dd); 1035 if (ret) { 1036 /* do not proceed if the firmware cannot be downloaded */ 1037 return_error = 1; 1038 goto done; 1039 } 1040 1041 /* step 5: set up device parameter settings */ 1042 dd_dev_info(dd, "%s: setting PCIe registers\n", __func__); 1043 1044 /* 1045 * PcieCfgSpcie1 - Link Control 3 1046 * Leave at reset value. No need to set PerfEq - link equalization 1047 * will be performed automatically after the SBR when the target 1048 * speed is 8GT/s. 1049 */ 1050 1051 /* clear all 16 per-lane error bits (PCIe: Lane Error Status) */ 1052 pci_write_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, 0xffff); 1053 1054 /* step 5a: Set Synopsys Port Logic registers */ 1055 1056 /* 1057 * PcieCfgRegPl2 - Port Force Link 1058 * 1059 * Set the low power field to 0x10 to avoid unnecessary power 1060 * management messages. All other fields are zero. 1061 */ 1062 reg32 = 0x10ul << PCIE_CFG_REG_PL2_LOW_PWR_ENT_CNT_SHIFT; 1063 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL2, reg32); 1064 1065 /* 1066 * PcieCfgRegPl100 - Gen3 Control 1067 * 1068 * turn off PcieCfgRegPl100.Gen3ZRxDcNonCompl 1069 * turn on PcieCfgRegPl100.EqEieosCnt 1070 * Everything else zero. 1071 */ 1072 reg32 = PCIE_CFG_REG_PL100_EQ_EIEOS_CNT_SMASK; 1073 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL100, reg32); 1074 1075 /* 1076 * PcieCfgRegPl101 - Gen3 EQ FS and LF 1077 * PcieCfgRegPl102 - Gen3 EQ Presets to Coefficients Mapping 1078 * PcieCfgRegPl103 - Gen3 EQ Preset Index 1079 * PcieCfgRegPl105 - Gen3 EQ Status 1080 * 1081 * Give initial EQ settings. 1082 */ 1083 if (dd->pcidev->device == PCI_DEVICE_ID_INTEL0) { /* discrete */ 1084 /* 1000mV, FS=24, LF = 8 */ 1085 fs = 24; 1086 lf = 8; 1087 div = 3; 1088 eq = discrete_preliminary_eq; 1089 default_pset = DEFAULT_DISCRETE_PSET; 1090 ctle_tunings = discrete_ctle_tunings; 1091 /* bit 0 - discrete on/off */ 1092 static_ctle_mode = pcie_ctle & 0x1; 1093 } else { 1094 /* 400mV, FS=29, LF = 9 */ 1095 fs = 29; 1096 lf = 9; 1097 div = 1; 1098 eq = integrated_preliminary_eq; 1099 default_pset = DEFAULT_MCP_PSET; 1100 ctle_tunings = integrated_ctle_tunings; 1101 /* bit 1 - integrated on/off */ 1102 static_ctle_mode = (pcie_ctle >> 1) & 0x1; 1103 } 1104 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL101, 1105 (fs << 1106 PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_FS_SHIFT) | 1107 (lf << 1108 PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_LF_SHIFT)); 1109 ret = load_eq_table(dd, eq, fs, div); 1110 if (ret) 1111 goto done; 1112 1113 /* 1114 * PcieCfgRegPl106 - Gen3 EQ Control 1115 * 1116 * Set Gen3EqPsetReqVec, leave other fields 0. 1117 */ 1118 if (pset == UNSET_PSET) 1119 pset = default_pset; 1120 if (pset > 10) { /* valid range is 0-10, inclusive */ 1121 dd_dev_err(dd, "%s: Invalid Eq Pset %u, setting to %d\n", 1122 __func__, pset, default_pset); 1123 pset = default_pset; 1124 } 1125 dd_dev_info(dd, "%s: using EQ Pset %u\n", __func__, pset); 1126 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL106, 1127 ((1 << pset) << 1128 PCIE_CFG_REG_PL106_GEN3_EQ_PSET_REQ_VEC_SHIFT) | 1129 PCIE_CFG_REG_PL106_GEN3_EQ_EVAL2MS_DISABLE_SMASK | 1130 PCIE_CFG_REG_PL106_GEN3_EQ_PHASE23_EXIT_MODE_SMASK); 1131 1132 /* 1133 * step 5b: Do post firmware download steps via SBus 1134 */ 1135 dd_dev_info(dd, "%s: doing pcie post steps\n", __func__); 1136 pcie_post_steps(dd); 1137 1138 /* 1139 * step 5c: Program gasket interrupts 1140 */ 1141 /* set the Rx Bit Rate to REFCLK ratio */ 1142 write_gasket_interrupt(dd, intnum++, 0x0006, 0x0050); 1143 /* disable pCal for PCIe Gen3 RX equalization */ 1144 /* select adaptive or static CTLE */ 1145 write_gasket_interrupt(dd, intnum++, 0x0026, 1146 0x5b01 | (static_ctle_mode << 3)); 1147 /* 1148 * Enable iCal for PCIe Gen3 RX equalization, and set which 1149 * evaluation of RX_EQ_EVAL will launch the iCal procedure. 1150 */ 1151 write_gasket_interrupt(dd, intnum++, 0x0026, 0x5202); 1152 1153 if (static_ctle_mode) { 1154 /* apply static CTLE tunings */ 1155 u8 pcie_dc, pcie_lf, pcie_hf, pcie_bw; 1156 1157 pcie_dc = ctle_tunings[pset][0]; 1158 pcie_lf = ctle_tunings[pset][1]; 1159 pcie_hf = ctle_tunings[pset][2]; 1160 pcie_bw = ctle_tunings[pset][3]; 1161 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0200 | pcie_dc); 1162 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0100 | pcie_lf); 1163 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0000 | pcie_hf); 1164 write_gasket_interrupt(dd, intnum++, 0x0026, 0x5500 | pcie_bw); 1165 } 1166 1167 /* terminate list */ 1168 write_gasket_interrupt(dd, intnum++, 0x0000, 0x0000); 1169 1170 /* 1171 * step 5d: program XMT margin 1172 */ 1173 write_xmt_margin(dd, __func__); 1174 1175 /* 1176 * step 5e: disable active state power management (ASPM). It 1177 * will be enabled if required later 1178 */ 1179 dd_dev_info(dd, "%s: clearing ASPM\n", __func__); 1180 aspm_hw_disable_l1(dd); 1181 1182 /* 1183 * step 5f: clear DirectSpeedChange 1184 * PcieCfgRegPl67.DirectSpeedChange must be zero to prevent the 1185 * change in the speed target from starting before we are ready. 1186 * This field defaults to 0 and we are not changing it, so nothing 1187 * needs to be done. 1188 */ 1189 1190 /* step 5g: Set target link speed */ 1191 /* 1192 * Set target link speed to be target on both device and parent. 1193 * On setting the parent: Some system BIOSs "helpfully" set the 1194 * parent target speed to Gen2 to match the ASIC's initial speed. 1195 * We can set the target Gen3 because we have already checked 1196 * that it is Gen3 capable earlier. 1197 */ 1198 dd_dev_info(dd, "%s: setting parent target link speed\n", __func__); 1199 ret = pcie_capability_read_word(parent, PCI_EXP_LNKCTL2, &lnkctl2); 1200 if (ret) { 1201 dd_dev_err(dd, "Unable to read from PCI config\n"); 1202 return_error = 1; 1203 goto done; 1204 } 1205 1206 dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__, 1207 (u32)lnkctl2); 1208 /* only write to parent if target is not as high as ours */ 1209 if ((lnkctl2 & PCI_EXP_LNKCTL2_TLS) < target_vector) { 1210 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; 1211 lnkctl2 |= target_vector; 1212 dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__, 1213 (u32)lnkctl2); 1214 ret = pcie_capability_write_word(parent, 1215 PCI_EXP_LNKCTL2, lnkctl2); 1216 if (ret) { 1217 dd_dev_err(dd, "Unable to write to PCI config\n"); 1218 return_error = 1; 1219 goto done; 1220 } 1221 } else { 1222 dd_dev_info(dd, "%s: ..target speed is OK\n", __func__); 1223 } 1224 1225 dd_dev_info(dd, "%s: setting target link speed\n", __func__); 1226 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL2, &lnkctl2); 1227 if (ret) { 1228 dd_dev_err(dd, "Unable to read from PCI config\n"); 1229 return_error = 1; 1230 goto done; 1231 } 1232 1233 dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__, 1234 (u32)lnkctl2); 1235 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; 1236 lnkctl2 |= target_vector; 1237 dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__, 1238 (u32)lnkctl2); 1239 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL2, lnkctl2); 1240 if (ret) { 1241 dd_dev_err(dd, "Unable to write to PCI config\n"); 1242 return_error = 1; 1243 goto done; 1244 } 1245 1246 /* step 5h: arm gasket logic */ 1247 /* hold DC in reset across the SBR */ 1248 write_csr(dd, CCE_DC_CTRL, CCE_DC_CTRL_DC_RESET_SMASK); 1249 (void)read_csr(dd, CCE_DC_CTRL); /* DC reset hold */ 1250 /* save firmware control across the SBR */ 1251 fw_ctrl = read_csr(dd, MISC_CFG_FW_CTRL); 1252 1253 dd_dev_info(dd, "%s: arming gasket logic\n", __func__); 1254 arm_gasket_logic(dd); 1255 1256 /* 1257 * step 6: quiesce PCIe link 1258 * The chip has already been reset, so there will be no traffic 1259 * from the chip. Linux has no easy way to enforce that it will 1260 * not try to access the device, so we just need to hope it doesn't 1261 * do it while we are doing the reset. 1262 */ 1263 1264 /* 1265 * step 7: initiate the secondary bus reset (SBR) 1266 * step 8: hardware brings the links back up 1267 * step 9: wait for link speed transition to be complete 1268 */ 1269 dd_dev_info(dd, "%s: calling trigger_sbr\n", __func__); 1270 ret = trigger_sbr(dd); 1271 if (ret) 1272 goto done; 1273 1274 /* step 10: decide what to do next */ 1275 1276 /* check if we can read PCI space */ 1277 ret = pci_read_config_word(dd->pcidev, PCI_VENDOR_ID, &vendor); 1278 if (ret) { 1279 dd_dev_info(dd, 1280 "%s: read of VendorID failed after SBR, err %d\n", 1281 __func__, ret); 1282 return_error = 1; 1283 goto done; 1284 } 1285 if (vendor == 0xffff) { 1286 dd_dev_info(dd, "%s: VendorID is all 1s after SBR\n", __func__); 1287 return_error = 1; 1288 ret = -EIO; 1289 goto done; 1290 } 1291 1292 /* restore PCI space registers we know were reset */ 1293 dd_dev_info(dd, "%s: calling restore_pci_variables\n", __func__); 1294 ret = restore_pci_variables(dd); 1295 if (ret) { 1296 dd_dev_err(dd, "%s: Could not restore PCI variables\n", 1297 __func__); 1298 return_error = 1; 1299 goto done; 1300 } 1301 1302 /* restore firmware control */ 1303 write_csr(dd, MISC_CFG_FW_CTRL, fw_ctrl); 1304 1305 /* 1306 * Check the gasket block status. 1307 * 1308 * This is the first CSR read after the SBR. If the read returns 1309 * all 1s (fails), the link did not make it back. 1310 * 1311 * Once we're sure we can read and write, clear the DC reset after 1312 * the SBR. Then check for any per-lane errors. Then look over 1313 * the status. 1314 */ 1315 reg = read_csr(dd, ASIC_PCIE_SD_HOST_STATUS); 1316 dd_dev_info(dd, "%s: gasket block status: 0x%llx\n", __func__, reg); 1317 if (reg == ~0ull) { /* PCIe read failed/timeout */ 1318 dd_dev_err(dd, "SBR failed - unable to read from device\n"); 1319 return_error = 1; 1320 ret = -ENOSYS; 1321 goto done; 1322 } 1323 1324 /* clear the DC reset */ 1325 write_csr(dd, CCE_DC_CTRL, 0); 1326 1327 /* Set the LED off */ 1328 setextled(dd, 0); 1329 1330 /* check for any per-lane errors */ 1331 ret = pci_read_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, ®32); 1332 if (ret) { 1333 dd_dev_err(dd, "Unable to read from PCI config\n"); 1334 return_error = 1; 1335 goto done; 1336 } 1337 1338 dd_dev_info(dd, "%s: per-lane errors: 0x%x\n", __func__, reg32); 1339 1340 /* extract status, look for our HFI */ 1341 status = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_SHIFT) 1342 & ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_MASK; 1343 if ((status & (1 << dd->hfi1_id)) == 0) { 1344 dd_dev_err(dd, 1345 "%s: gasket status 0x%x, expecting 0x%x\n", 1346 __func__, status, 1 << dd->hfi1_id); 1347 ret = -EIO; 1348 goto done; 1349 } 1350 1351 /* extract error */ 1352 err = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_SHIFT) 1353 & ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_MASK; 1354 if (err) { 1355 dd_dev_err(dd, "%s: gasket error %d\n", __func__, err); 1356 ret = -EIO; 1357 goto done; 1358 } 1359 1360 /* update our link information cache */ 1361 update_lbus_info(dd); 1362 dd_dev_info(dd, "%s: new speed and width: %s\n", __func__, 1363 dd->lbus_info); 1364 1365 if (dd->lbus_speed != target_speed || 1366 dd->lbus_width < target_width) { /* not target */ 1367 /* maybe retry */ 1368 do_retry = retry_count < pcie_retry; 1369 dd_dev_err(dd, "PCIe link speed or width did not match target%s\n", 1370 do_retry ? ", retrying" : ""); 1371 retry_count++; 1372 if (do_retry) { 1373 msleep(100); /* allow time to settle */ 1374 goto retry; 1375 } 1376 ret = -EIO; 1377 } 1378 1379 done: 1380 if (therm) { 1381 write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x1); 1382 msleep(100); 1383 dd_dev_info(dd, "%s: Re-enable therm polling\n", 1384 __func__); 1385 } 1386 release_chip_resource(dd, CR_SBUS); 1387 done_no_mutex: 1388 /* return no error if it is OK to be at current speed */ 1389 if (ret && !return_error) { 1390 dd_dev_err(dd, "Proceeding at current speed PCIe speed\n"); 1391 ret = 0; 1392 } 1393 1394 dd_dev_info(dd, "%s: done\n", __func__); 1395 return ret; 1396 } 1397