1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #include <linux/bitops.h> 3 #include <linux/device.h> 4 #include <linux/iio/iio.h> 5 #include <linux/regmap.h> 6 #include <linux/regulator/consumer.h> 7 8 9 /* BMP580 specific registers */ 10 #define BMP580_REG_CMD 0x7E 11 #define BMP580_REG_EFF_OSR 0x38 12 #define BMP580_REG_ODR_CONFIG 0x37 13 #define BMP580_REG_OSR_CONFIG 0x36 14 #define BMP580_REG_IF_CONFIG 0x13 15 #define BMP580_REG_REV_ID 0x02 16 #define BMP580_REG_CHIP_ID 0x01 17 /* OOR allows to configure a pressure alarm */ 18 #define BMP580_REG_OOR_CONFIG 0x35 19 #define BMP580_REG_OOR_RANGE 0x34 20 #define BMP580_REG_OOR_THR_MSB 0x33 21 #define BMP580_REG_OOR_THR_LSB 0x32 22 /* DSP registers (IIR filters) */ 23 #define BMP580_REG_DSP_IIR 0x31 24 #define BMP580_REG_DSP_CONFIG 0x30 25 /* NVM access registers */ 26 #define BMP580_REG_NVM_DATA_MSB 0x2D 27 #define BMP580_REG_NVM_DATA_LSB 0x2C 28 #define BMP580_REG_NVM_ADDR 0x2B 29 /* Status registers */ 30 #define BMP580_REG_STATUS 0x28 31 #define BMP580_REG_INT_STATUS 0x27 32 #define BMP580_REG_CHIP_STATUS 0x11 33 /* Data registers */ 34 #define BMP580_REG_FIFO_DATA 0x29 35 #define BMP580_REG_PRESS_MSB 0x22 36 #define BMP580_REG_PRESS_LSB 0x21 37 #define BMP580_REG_PRESS_XLSB 0x20 38 #define BMP580_REG_TEMP_MSB 0x1F 39 #define BMP580_REG_TEMP_LSB 0x1E 40 #define BMP580_REG_TEMP_XLSB 0x1D 41 /* FIFO config registers */ 42 #define BMP580_REG_FIFO_SEL 0x18 43 #define BMP580_REG_FIFO_COUNT 0x17 44 #define BMP580_REG_FIFO_CONFIG 0x16 45 /* Interruptions config registers */ 46 #define BMP580_REG_INT_SOURCE 0x15 47 #define BMP580_REG_INT_CONFIG 0x14 48 49 #define BMP580_CMD_NOOP 0x00 50 #define BMP580_CMD_EXTMODE_SEQ_0 0x73 51 #define BMP580_CMD_EXTMODE_SEQ_1 0xB4 52 #define BMP580_CMD_EXTMODE_SEQ_2 0x69 53 #define BMP580_CMD_NVM_OP_SEQ_0 0x5D 54 #define BMP580_CMD_NVM_READ_SEQ_1 0xA5 55 #define BMP580_CMD_NVM_WRITE_SEQ_1 0xA0 56 #define BMP580_CMD_SOFT_RESET 0xB6 57 58 #define BMP580_INT_STATUS_POR_MASK BIT(4) 59 60 #define BMP580_STATUS_CORE_RDY_MASK BIT(0) 61 #define BMP580_STATUS_NVM_RDY_MASK BIT(1) 62 #define BMP580_STATUS_NVM_ERR_MASK BIT(2) 63 #define BMP580_STATUS_NVM_CMD_ERR_MASK BIT(3) 64 65 #define BMP580_OSR_PRESS_MASK GENMASK(5, 3) 66 #define BMP580_OSR_TEMP_MASK GENMASK(2, 0) 67 #define BMP580_OSR_PRESS_EN BIT(6) 68 #define BMP580_EFF_OSR_PRESS_MASK GENMASK(5, 3) 69 #define BMP580_EFF_OSR_TEMP_MASK GENMASK(2, 0) 70 #define BMP580_EFF_OSR_VALID_ODR BIT(7) 71 72 #define BMP580_ODR_MASK GENMASK(6, 2) 73 #define BMP580_MODE_MASK GENMASK(1, 0) 74 #define BMP580_MODE_SLEEP 0 75 #define BMP580_MODE_NORMAL 1 76 #define BMP580_MODE_FORCED 2 77 #define BMP580_MODE_CONTINOUS 3 78 #define BMP580_ODR_DEEPSLEEP_DIS BIT(7) 79 80 #define BMP580_DSP_COMP_MASK GENMASK(1, 0) 81 #define BMP580_DSP_COMP_DIS 0 82 #define BMP580_DSP_TEMP_COMP_EN 1 83 /* 84 * In section 7.27 of datasheet, modes 2 and 3 are technically the same. 85 * Pressure compensation means also enabling temperature compensation 86 */ 87 #define BMP580_DSP_PRESS_COMP_EN 2 88 #define BMP580_DSP_PRESS_TEMP_COMP_EN 3 89 #define BMP580_DSP_IIR_FORCED_FLUSH BIT(2) 90 #define BMP580_DSP_SHDW_IIR_TEMP_EN BIT(3) 91 #define BMP580_DSP_FIFO_IIR_TEMP_EN BIT(4) 92 #define BMP580_DSP_SHDW_IIR_PRESS_EN BIT(5) 93 #define BMP580_DSP_FIFO_IIR_PRESS_EN BIT(6) 94 #define BMP580_DSP_OOR_IIR_PRESS_EN BIT(7) 95 96 #define BMP580_DSP_IIR_PRESS_MASK GENMASK(5, 3) 97 #define BMP580_DSP_IIR_TEMP_MASK GENMASK(2, 0) 98 #define BMP580_FILTER_OFF 0 99 #define BMP580_FILTER_1X 1 100 #define BMP580_FILTER_3X 2 101 #define BMP580_FILTER_7X 3 102 #define BMP580_FILTER_15X 4 103 #define BMP580_FILTER_31X 5 104 #define BMP580_FILTER_63X 6 105 #define BMP580_FILTER_127X 7 106 107 #define BMP580_NVM_ROW_ADDR_MASK GENMASK(5, 0) 108 #define BMP580_NVM_PROG_EN BIT(6) 109 110 #define BMP580_TEMP_SKIPPED 0x7f7f7f 111 #define BMP580_PRESS_SKIPPED 0x7f7f7f 112 113 /* BMP380 specific registers */ 114 #define BMP380_REG_CMD 0x7E 115 #define BMP380_REG_CONFIG 0x1F 116 #define BMP380_REG_ODR 0x1D 117 #define BMP380_REG_OSR 0x1C 118 #define BMP380_REG_POWER_CONTROL 0x1B 119 #define BMP380_REG_IF_CONFIG 0x1A 120 #define BMP380_REG_INT_CONTROL 0x19 121 #define BMP380_REG_INT_STATUS 0x11 122 #define BMP380_REG_EVENT 0x10 123 #define BMP380_REG_STATUS 0x03 124 #define BMP380_REG_ERROR 0x02 125 #define BMP380_REG_ID 0x00 126 127 #define BMP380_REG_FIFO_CONFIG_1 0x18 128 #define BMP380_REG_FIFO_CONFIG_2 0x17 129 #define BMP380_REG_FIFO_WATERMARK_MSB 0x16 130 #define BMP380_REG_FIFO_WATERMARK_LSB 0x15 131 #define BMP380_REG_FIFO_DATA 0x14 132 #define BMP380_REG_FIFO_LENGTH_MSB 0x13 133 #define BMP380_REG_FIFO_LENGTH_LSB 0x12 134 135 #define BMP380_REG_SENSOR_TIME_MSB 0x0E 136 #define BMP380_REG_SENSOR_TIME_LSB 0x0D 137 #define BMP380_REG_SENSOR_TIME_XLSB 0x0C 138 139 #define BMP380_REG_TEMP_MSB 0x09 140 #define BMP380_REG_TEMP_LSB 0x08 141 #define BMP380_REG_TEMP_XLSB 0x07 142 143 #define BMP380_REG_PRESS_MSB 0x06 144 #define BMP380_REG_PRESS_LSB 0x05 145 #define BMP380_REG_PRESS_XLSB 0x04 146 147 #define BMP380_REG_CALIB_TEMP_START 0x31 148 #define BMP380_CALIB_REG_COUNT 21 149 150 #define BMP380_FILTER_MASK GENMASK(3, 1) 151 #define BMP380_FILTER_OFF 0 152 #define BMP380_FILTER_1X 1 153 #define BMP380_FILTER_3X 2 154 #define BMP380_FILTER_7X 3 155 #define BMP380_FILTER_15X 4 156 #define BMP380_FILTER_31X 5 157 #define BMP380_FILTER_63X 6 158 #define BMP380_FILTER_127X 7 159 160 #define BMP380_OSRS_TEMP_MASK GENMASK(5, 3) 161 #define BMP380_OSRS_PRESS_MASK GENMASK(2, 0) 162 163 #define BMP380_ODRS_MASK GENMASK(4, 0) 164 165 #define BMP380_CTRL_SENSORS_MASK GENMASK(1, 0) 166 #define BMP380_CTRL_SENSORS_PRESS_EN BIT(0) 167 #define BMP380_CTRL_SENSORS_TEMP_EN BIT(1) 168 #define BMP380_MODE_MASK GENMASK(5, 4) 169 #define BMP380_MODE_SLEEP 0 170 #define BMP380_MODE_FORCED 1 171 #define BMP380_MODE_NORMAL 3 172 173 #define BMP380_MIN_TEMP -4000 174 #define BMP380_MAX_TEMP 8500 175 #define BMP380_MIN_PRES 3000000 176 #define BMP380_MAX_PRES 12500000 177 178 #define BMP380_CMD_NOOP 0x00 179 #define BMP380_CMD_EXTMODE_EN_MID 0x34 180 #define BMP380_CMD_FIFO_FLUSH 0xB0 181 #define BMP380_CMD_SOFT_RESET 0xB6 182 183 #define BMP380_STATUS_CMD_RDY_MASK BIT(4) 184 #define BMP380_STATUS_DRDY_PRESS_MASK BIT(5) 185 #define BMP380_STATUS_DRDY_TEMP_MASK BIT(6) 186 187 #define BMP380_ERR_FATAL_MASK BIT(0) 188 #define BMP380_ERR_CMD_MASK BIT(1) 189 #define BMP380_ERR_CONF_MASK BIT(2) 190 191 #define BMP380_TEMP_SKIPPED 0x800000 192 #define BMP380_PRESS_SKIPPED 0x800000 193 194 /* BMP280 specific registers */ 195 #define BMP280_REG_HUMIDITY_LSB 0xFE 196 #define BMP280_REG_HUMIDITY_MSB 0xFD 197 #define BMP280_REG_TEMP_XLSB 0xFC 198 #define BMP280_REG_TEMP_LSB 0xFB 199 #define BMP280_REG_TEMP_MSB 0xFA 200 #define BMP280_REG_PRESS_XLSB 0xF9 201 #define BMP280_REG_PRESS_LSB 0xF8 202 #define BMP280_REG_PRESS_MSB 0xF7 203 204 /* Helper mask to truncate excess 4 bits on pressure and temp readings */ 205 #define BMP280_MEAS_TRIM_MASK GENMASK(24, 4) 206 207 #define BMP280_REG_CONFIG 0xF5 208 #define BMP280_REG_CTRL_MEAS 0xF4 209 #define BMP280_REG_STATUS 0xF3 210 #define BMP280_REG_CTRL_HUMIDITY 0xF2 211 212 /* Due to non linear mapping, and data sizes we can't do a bulk read */ 213 #define BMP280_REG_COMP_H1 0xA1 214 #define BMP280_REG_COMP_H2 0xE1 215 #define BMP280_REG_COMP_H3 0xE3 216 #define BMP280_REG_COMP_H4 0xE4 217 #define BMP280_REG_COMP_H5 0xE5 218 #define BMP280_REG_COMP_H6 0xE7 219 220 #define BMP280_REG_COMP_TEMP_START 0x88 221 #define BMP280_COMP_TEMP_REG_COUNT 6 222 223 #define BMP280_REG_COMP_PRESS_START 0x8E 224 #define BMP280_COMP_PRESS_REG_COUNT 18 225 226 #define BMP280_COMP_H5_MASK GENMASK(15, 4) 227 228 #define BMP280_CONTIGUOUS_CALIB_REGS (BMP280_COMP_TEMP_REG_COUNT + \ 229 BMP280_COMP_PRESS_REG_COUNT) 230 231 #define BMP280_FILTER_MASK GENMASK(4, 2) 232 #define BMP280_FILTER_OFF 0 233 #define BMP280_FILTER_2X 1 234 #define BMP280_FILTER_4X 2 235 #define BMP280_FILTER_8X 3 236 #define BMP280_FILTER_16X 4 237 238 #define BMP280_OSRS_HUMIDITY_MASK GENMASK(2, 0) 239 #define BMP280_OSRS_HUMIDITY_SKIP 0 240 #define BMP280_OSRS_HUMIDITY_1X 1 241 #define BMP280_OSRS_HUMIDITY_2X 2 242 #define BMP280_OSRS_HUMIDITY_4X 3 243 #define BMP280_OSRS_HUMIDITY_8X 4 244 #define BMP280_OSRS_HUMIDITY_16X 5 245 246 #define BMP280_OSRS_TEMP_MASK GENMASK(7, 5) 247 #define BMP280_OSRS_TEMP_SKIP 0 248 #define BMP280_OSRS_TEMP_1X 1 249 #define BMP280_OSRS_TEMP_2X 2 250 #define BMP280_OSRS_TEMP_4X 3 251 #define BMP280_OSRS_TEMP_8X 4 252 #define BMP280_OSRS_TEMP_16X 5 253 254 #define BMP280_OSRS_PRESS_MASK GENMASK(4, 2) 255 #define BMP280_OSRS_PRESS_SKIP 0 256 #define BMP280_OSRS_PRESS_1X 1 257 #define BMP280_OSRS_PRESS_2X 2 258 #define BMP280_OSRS_PRESS_4X 3 259 #define BMP280_OSRS_PRESS_8X 4 260 #define BMP280_OSRS_PRESS_16X 5 261 262 #define BMP280_MODE_MASK GENMASK(1, 0) 263 #define BMP280_MODE_SLEEP 0 264 #define BMP280_MODE_FORCED 1 265 #define BMP280_MODE_NORMAL 3 266 267 /* BMP180 specific registers */ 268 #define BMP180_REG_OUT_XLSB 0xF8 269 #define BMP180_REG_OUT_LSB 0xF7 270 #define BMP180_REG_OUT_MSB 0xF6 271 272 #define BMP180_REG_CALIB_START 0xAA 273 #define BMP180_REG_CALIB_COUNT 22 274 275 #define BMP180_MEAS_CTRL_MASK GENMASK(4, 0) 276 #define BMP180_MEAS_TEMP 0x0E 277 #define BMP180_MEAS_PRESS 0x14 278 #define BMP180_MEAS_SCO BIT(5) 279 #define BMP180_OSRS_PRESS_MASK GENMASK(7, 6) 280 #define BMP180_MEAS_PRESS_1X 0 281 #define BMP180_MEAS_PRESS_2X 1 282 #define BMP180_MEAS_PRESS_4X 2 283 #define BMP180_MEAS_PRESS_8X 3 284 285 /* BMP180 and BMP280 common registers */ 286 #define BMP280_REG_CTRL_MEAS 0xF4 287 #define BMP280_REG_RESET 0xE0 288 #define BMP280_REG_ID 0xD0 289 290 #define BMP380_CHIP_ID 0x50 291 #define BMP580_CHIP_ID 0x50 292 #define BMP580_CHIP_ID_ALT 0x51 293 #define BMP180_CHIP_ID 0x55 294 #define BMP280_CHIP_ID 0x58 295 #define BME280_CHIP_ID 0x60 296 #define BMP280_SOFT_RESET_VAL 0xB6 297 298 /* BMP280 register skipped special values */ 299 #define BMP280_TEMP_SKIPPED 0x80000 300 #define BMP280_PRESS_SKIPPED 0x80000 301 #define BMP280_HUMIDITY_SKIPPED 0x8000 302 303 /* Core exported structs */ 304 305 static const char *const bmp280_supply_names[] = { 306 "vddd", "vdda" 307 }; 308 309 #define BMP280_NUM_SUPPLIES ARRAY_SIZE(bmp280_supply_names) 310 311 struct bmp180_calib { 312 s16 AC1; 313 s16 AC2; 314 s16 AC3; 315 u16 AC4; 316 u16 AC5; 317 u16 AC6; 318 s16 B1; 319 s16 B2; 320 s16 MB; 321 s16 MC; 322 s16 MD; 323 }; 324 325 /* See datasheet Section 4.2.2. */ 326 struct bmp280_calib { 327 u16 T1; 328 s16 T2; 329 s16 T3; 330 u16 P1; 331 s16 P2; 332 s16 P3; 333 s16 P4; 334 s16 P5; 335 s16 P6; 336 s16 P7; 337 s16 P8; 338 s16 P9; 339 u8 H1; 340 s16 H2; 341 u8 H3; 342 s16 H4; 343 s16 H5; 344 s8 H6; 345 }; 346 347 /* See datasheet Section 3.11.1. */ 348 struct bmp380_calib { 349 u16 T1; 350 u16 T2; 351 s8 T3; 352 s16 P1; 353 s16 P2; 354 s8 P3; 355 s8 P4; 356 u16 P5; 357 u16 P6; 358 s8 P7; 359 s8 P8; 360 s16 P9; 361 s8 P10; 362 s8 P11; 363 }; 364 365 struct bmp280_data { 366 struct device *dev; 367 struct mutex lock; 368 struct regmap *regmap; 369 struct completion done; 370 bool use_eoc; 371 const struct bmp280_chip_info *chip_info; 372 union { 373 struct bmp180_calib bmp180; 374 struct bmp280_calib bmp280; 375 struct bmp380_calib bmp380; 376 } calib; 377 struct regulator_bulk_data supplies[BMP280_NUM_SUPPLIES]; 378 unsigned int start_up_time; /* in microseconds */ 379 380 /* log of base 2 of oversampling rate */ 381 u8 oversampling_press; 382 u8 oversampling_temp; 383 u8 oversampling_humid; 384 u8 iir_filter_coeff; 385 386 /* 387 * BMP380 devices introduce sampling frequency configuration. See 388 * datasheet sections 3.3.3. and 4.3.19 for more details. 389 * 390 * BMx280 devices allowed indirect configuration of sampling frequency 391 * changing the t_standby duration between measurements, as detailed on 392 * section 3.6.3 of the datasheet. 393 */ 394 int sampling_freq; 395 396 /* 397 * Carryover value from temperature conversion, used in pressure 398 * calculation. 399 */ 400 s32 t_fine; 401 402 /* 403 * DMA (thus cache coherency maintenance) may require the 404 * transfer buffers to live in their own cache lines. 405 */ 406 union { 407 /* Sensor data buffer */ 408 u8 buf[3]; 409 /* Calibration data buffers */ 410 __le16 bmp280_cal_buf[BMP280_CONTIGUOUS_CALIB_REGS / 2]; 411 __be16 bmp180_cal_buf[BMP180_REG_CALIB_COUNT / 2]; 412 u8 bmp380_cal_buf[BMP380_CALIB_REG_COUNT]; 413 /* Miscellaneous, endianness-aware data buffers */ 414 __le16 le16; 415 __be16 be16; 416 } __aligned(IIO_DMA_MINALIGN); 417 }; 418 419 struct bmp280_chip_info { 420 unsigned int id_reg; 421 const unsigned int chip_id; 422 423 const struct regmap_config *regmap_config; 424 425 const struct iio_chan_spec *channels; 426 int num_channels; 427 unsigned int start_up_time; 428 429 const int *oversampling_temp_avail; 430 int num_oversampling_temp_avail; 431 int oversampling_temp_default; 432 433 const int *oversampling_press_avail; 434 int num_oversampling_press_avail; 435 int oversampling_press_default; 436 437 const int *oversampling_humid_avail; 438 int num_oversampling_humid_avail; 439 int oversampling_humid_default; 440 441 const int *iir_filter_coeffs_avail; 442 int num_iir_filter_coeffs_avail; 443 int iir_filter_coeff_default; 444 445 const int (*sampling_freq_avail)[2]; 446 int num_sampling_freq_avail; 447 int sampling_freq_default; 448 449 int (*chip_config)(struct bmp280_data *); 450 int (*read_temp)(struct bmp280_data *, int *, int *); 451 int (*read_press)(struct bmp280_data *, int *, int *); 452 int (*read_humid)(struct bmp280_data *, int *, int *); 453 int (*read_calib)(struct bmp280_data *); 454 int (*preinit)(struct bmp280_data *); 455 }; 456 457 /* Chip infos for each variant */ 458 extern const struct bmp280_chip_info bmp180_chip_info; 459 extern const struct bmp280_chip_info bmp280_chip_info; 460 extern const struct bmp280_chip_info bme280_chip_info; 461 extern const struct bmp280_chip_info bmp380_chip_info; 462 extern const struct bmp280_chip_info bmp580_chip_info; 463 464 /* Regmap configurations */ 465 extern const struct regmap_config bmp180_regmap_config; 466 extern const struct regmap_config bmp280_regmap_config; 467 extern const struct regmap_config bmp380_regmap_config; 468 extern const struct regmap_config bmp580_regmap_config; 469 470 /* Probe called from different transports */ 471 int bmp280_common_probe(struct device *dev, 472 struct regmap *regmap, 473 const struct bmp280_chip_info *, 474 const char *name, 475 int irq); 476 477 /* PM ops */ 478 extern const struct dev_pm_ops bmp280_dev_pm_ops; 479