1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Copyright (C) 2012 Invensense, Inc. 4 */ 5 #include <linux/i2c.h> 6 #include <linux/i2c-mux.h> 7 #include <linux/mutex.h> 8 #include <linux/iio/iio.h> 9 #include <linux/iio/buffer.h> 10 #include <linux/regmap.h> 11 #include <linux/iio/sysfs.h> 12 #include <linux/iio/kfifo_buf.h> 13 #include <linux/iio/trigger.h> 14 #include <linux/iio/triggered_buffer.h> 15 #include <linux/iio/trigger_consumer.h> 16 #include <linux/platform_data/invensense_mpu6050.h> 17 18 /** 19 * struct inv_mpu6050_reg_map - Notable registers. 20 * @sample_rate_div: Divider applied to gyro output rate. 21 * @lpf: Configures internal low pass filter. 22 * @accel_lpf: Configures accelerometer low pass filter. 23 * @user_ctrl: Enables/resets the FIFO. 24 * @fifo_en: Determines which data will appear in FIFO. 25 * @gyro_config: gyro config register. 26 * @accl_config: accel config register 27 * @fifo_count_h: Upper byte of FIFO count. 28 * @fifo_r_w: FIFO register. 29 * @raw_gyro: Address of first gyro register. 30 * @raw_accl: Address of first accel register. 31 * @temperature: temperature register 32 * @int_enable: Interrupt enable register. 33 * @int_status: Interrupt status register. 34 * @pwr_mgmt_1: Controls chip's power state and clock source. 35 * @pwr_mgmt_2: Controls power state of individual sensors. 36 * @int_pin_cfg; Controls interrupt pin configuration. 37 * @accl_offset: Controls the accelerometer calibration offset. 38 * @gyro_offset: Controls the gyroscope calibration offset. 39 * @i2c_if: Controls the i2c interface 40 */ 41 struct inv_mpu6050_reg_map { 42 u8 sample_rate_div; 43 u8 lpf; 44 u8 accel_lpf; 45 u8 user_ctrl; 46 u8 fifo_en; 47 u8 gyro_config; 48 u8 accl_config; 49 u8 fifo_count_h; 50 u8 fifo_r_w; 51 u8 raw_gyro; 52 u8 raw_accl; 53 u8 temperature; 54 u8 int_enable; 55 u8 int_status; 56 u8 pwr_mgmt_1; 57 u8 pwr_mgmt_2; 58 u8 int_pin_cfg; 59 u8 accl_offset; 60 u8 gyro_offset; 61 u8 i2c_if; 62 }; 63 64 /*device enum */ 65 enum inv_devices { 66 INV_MPU6050, 67 INV_MPU6500, 68 INV_MPU6515, 69 INV_MPU6000, 70 INV_MPU9150, 71 INV_MPU9250, 72 INV_MPU9255, 73 INV_ICM20608, 74 INV_ICM20602, 75 INV_NUM_PARTS 76 }; 77 78 /** 79 * struct inv_mpu6050_chip_config - Cached chip configuration data. 80 * @fsr: Full scale range. 81 * @lpf: Digital low pass filter frequency. 82 * @accl_fs: accel full scale range. 83 * @accl_fifo_enable: enable accel data output 84 * @gyro_fifo_enable: enable gyro data output 85 * @divider: chip sample rate divider (sample rate divider - 1) 86 */ 87 struct inv_mpu6050_chip_config { 88 unsigned int fsr:2; 89 unsigned int lpf:3; 90 unsigned int accl_fs:2; 91 unsigned int accl_fifo_enable:1; 92 unsigned int gyro_fifo_enable:1; 93 u8 divider; 94 u8 user_ctrl; 95 }; 96 97 /** 98 * struct inv_mpu6050_hw - Other important hardware information. 99 * @whoami: Self identification byte from WHO_AM_I register 100 * @name: name of the chip. 101 * @reg: register map of the chip. 102 * @config: configuration of the chip. 103 */ 104 struct inv_mpu6050_hw { 105 u8 whoami; 106 u8 *name; 107 const struct inv_mpu6050_reg_map *reg; 108 const struct inv_mpu6050_chip_config *config; 109 }; 110 111 /* 112 * struct inv_mpu6050_state - Driver state variables. 113 * @lock: Chip access lock. 114 * @trig: IIO trigger. 115 * @chip_config: Cached attribute information. 116 * @reg: Map of important registers. 117 * @hw: Other hardware-specific information. 118 * @chip_type: chip type. 119 * @plat_data: platform data (deprecated in favor of @orientation). 120 * @orientation: sensor chip orientation relative to main hardware. 121 * @map regmap pointer. 122 * @irq interrupt number. 123 * @irq_mask the int_pin_cfg mask to configure interrupt type. 124 * @chip_period: chip internal period estimation (~1kHz). 125 * @it_timestamp: timestamp from previous interrupt. 126 * @data_timestamp: timestamp for next data sample. 127 * @vddio_supply voltage regulator for the chip. 128 */ 129 struct inv_mpu6050_state { 130 struct mutex lock; 131 struct iio_trigger *trig; 132 struct inv_mpu6050_chip_config chip_config; 133 const struct inv_mpu6050_reg_map *reg; 134 const struct inv_mpu6050_hw *hw; 135 enum inv_devices chip_type; 136 struct i2c_mux_core *muxc; 137 struct i2c_client *mux_client; 138 unsigned int powerup_count; 139 struct inv_mpu6050_platform_data plat_data; 140 struct iio_mount_matrix orientation; 141 struct regmap *map; 142 int irq; 143 u8 irq_mask; 144 unsigned skip_samples; 145 s64 chip_period; 146 s64 it_timestamp; 147 s64 data_timestamp; 148 struct regulator *vddio_supply; 149 }; 150 151 /*register and associated bit definition*/ 152 #define INV_MPU6050_REG_ACCEL_OFFSET 0x06 153 #define INV_MPU6050_REG_GYRO_OFFSET 0x13 154 155 #define INV_MPU6050_REG_SAMPLE_RATE_DIV 0x19 156 #define INV_MPU6050_REG_CONFIG 0x1A 157 #define INV_MPU6050_REG_GYRO_CONFIG 0x1B 158 #define INV_MPU6050_REG_ACCEL_CONFIG 0x1C 159 160 #define INV_MPU6050_REG_FIFO_EN 0x23 161 #define INV_MPU6050_BIT_ACCEL_OUT 0x08 162 #define INV_MPU6050_BITS_GYRO_OUT 0x70 163 164 #define INV_MPU6050_REG_INT_ENABLE 0x38 165 #define INV_MPU6050_BIT_DATA_RDY_EN 0x01 166 #define INV_MPU6050_BIT_DMP_INT_EN 0x02 167 168 #define INV_MPU6050_REG_RAW_ACCEL 0x3B 169 #define INV_MPU6050_REG_TEMPERATURE 0x41 170 #define INV_MPU6050_REG_RAW_GYRO 0x43 171 172 #define INV_MPU6050_REG_INT_STATUS 0x3A 173 #define INV_MPU6050_BIT_FIFO_OVERFLOW_INT 0x10 174 #define INV_MPU6050_BIT_RAW_DATA_RDY_INT 0x01 175 176 #define INV_MPU6050_REG_USER_CTRL 0x6A 177 #define INV_MPU6050_BIT_FIFO_RST 0x04 178 #define INV_MPU6050_BIT_DMP_RST 0x08 179 #define INV_MPU6050_BIT_I2C_MST_EN 0x20 180 #define INV_MPU6050_BIT_FIFO_EN 0x40 181 #define INV_MPU6050_BIT_DMP_EN 0x80 182 #define INV_MPU6050_BIT_I2C_IF_DIS 0x10 183 184 #define INV_MPU6050_REG_PWR_MGMT_1 0x6B 185 #define INV_MPU6050_BIT_H_RESET 0x80 186 #define INV_MPU6050_BIT_SLEEP 0x40 187 #define INV_MPU6050_BIT_CLK_MASK 0x7 188 189 #define INV_MPU6050_REG_PWR_MGMT_2 0x6C 190 #define INV_MPU6050_BIT_PWR_ACCL_STBY 0x38 191 #define INV_MPU6050_BIT_PWR_GYRO_STBY 0x07 192 193 /* ICM20602 register */ 194 #define INV_ICM20602_REG_I2C_IF 0x70 195 #define INV_ICM20602_BIT_I2C_IF_DIS 0x40 196 197 #define INV_MPU6050_REG_FIFO_COUNT_H 0x72 198 #define INV_MPU6050_REG_FIFO_R_W 0x74 199 200 #define INV_MPU6050_BYTES_PER_3AXIS_SENSOR 6 201 #define INV_MPU6050_FIFO_COUNT_BYTE 2 202 203 /* ICM20602 FIFO samples include temperature readings */ 204 #define INV_ICM20602_BYTES_PER_TEMP_SENSOR 2 205 206 /* mpu6500 registers */ 207 #define INV_MPU6500_REG_ACCEL_CONFIG_2 0x1D 208 #define INV_MPU6500_REG_ACCEL_OFFSET 0x77 209 210 /* delay time in milliseconds */ 211 #define INV_MPU6050_POWER_UP_TIME 100 212 #define INV_MPU6050_TEMP_UP_TIME 100 213 #define INV_MPU6050_SENSOR_UP_TIME 30 214 215 /* delay time in microseconds */ 216 #define INV_MPU6050_REG_UP_TIME_MIN 5000 217 #define INV_MPU6050_REG_UP_TIME_MAX 10000 218 219 #define INV_MPU6050_TEMP_OFFSET 12421 220 #define INV_MPU6050_TEMP_SCALE 2941 221 #define INV_MPU6050_MAX_GYRO_FS_PARAM 3 222 #define INV_MPU6050_MAX_ACCL_FS_PARAM 3 223 #define INV_MPU6050_THREE_AXIS 3 224 #define INV_MPU6050_GYRO_CONFIG_FSR_SHIFT 3 225 #define INV_MPU6050_ACCL_CONFIG_FSR_SHIFT 3 226 227 #define INV_ICM20602_TEMP_OFFSET 8170 228 #define INV_ICM20602_TEMP_SCALE 3060 229 230 /* 6 + 6 round up and plus 8 */ 231 #define INV_MPU6050_OUTPUT_DATA_SIZE 24 232 233 #define INV_MPU6050_REG_INT_PIN_CFG 0x37 234 #define INV_MPU6050_ACTIVE_HIGH 0x00 235 #define INV_MPU6050_ACTIVE_LOW 0x80 236 /* enable level triggering */ 237 #define INV_MPU6050_LATCH_INT_EN 0x20 238 #define INV_MPU6050_BIT_BYPASS_EN 0x2 239 240 /* Allowed timestamp period jitter in percent */ 241 #define INV_MPU6050_TS_PERIOD_JITTER 4 242 243 /* init parameters */ 244 #define INV_MPU6050_INIT_FIFO_RATE 50 245 #define INV_MPU6050_MAX_FIFO_RATE 1000 246 #define INV_MPU6050_MIN_FIFO_RATE 4 247 248 /* chip internal frequency: 1KHz */ 249 #define INV_MPU6050_INTERNAL_FREQ_HZ 1000 250 /* return the frequency divider (chip sample rate divider + 1) */ 251 #define INV_MPU6050_FREQ_DIVIDER(st) \ 252 ((st)->chip_config.divider + 1) 253 /* chip sample rate divider to fifo rate */ 254 #define INV_MPU6050_FIFO_RATE_TO_DIVIDER(fifo_rate) \ 255 ((INV_MPU6050_INTERNAL_FREQ_HZ / (fifo_rate)) - 1) 256 #define INV_MPU6050_DIVIDER_TO_FIFO_RATE(divider) \ 257 (INV_MPU6050_INTERNAL_FREQ_HZ / ((divider) + 1)) 258 259 #define INV_MPU6050_REG_WHOAMI 117 260 261 #define INV_MPU6000_WHOAMI_VALUE 0x68 262 #define INV_MPU6050_WHOAMI_VALUE 0x68 263 #define INV_MPU6500_WHOAMI_VALUE 0x70 264 #define INV_MPU9150_WHOAMI_VALUE 0x68 265 #define INV_MPU9250_WHOAMI_VALUE 0x71 266 #define INV_MPU9255_WHOAMI_VALUE 0x73 267 #define INV_MPU6515_WHOAMI_VALUE 0x74 268 #define INV_ICM20608_WHOAMI_VALUE 0xAF 269 #define INV_ICM20602_WHOAMI_VALUE 0x12 270 271 /* scan element definition for generic MPU6xxx devices */ 272 enum inv_mpu6050_scan { 273 INV_MPU6050_SCAN_ACCL_X, 274 INV_MPU6050_SCAN_ACCL_Y, 275 INV_MPU6050_SCAN_ACCL_Z, 276 INV_MPU6050_SCAN_GYRO_X, 277 INV_MPU6050_SCAN_GYRO_Y, 278 INV_MPU6050_SCAN_GYRO_Z, 279 INV_MPU6050_SCAN_TIMESTAMP, 280 }; 281 282 /* scan element definition for ICM20602, which includes temperature */ 283 enum inv_icm20602_scan { 284 INV_ICM20602_SCAN_ACCL_X, 285 INV_ICM20602_SCAN_ACCL_Y, 286 INV_ICM20602_SCAN_ACCL_Z, 287 INV_ICM20602_SCAN_TEMP, 288 INV_ICM20602_SCAN_GYRO_X, 289 INV_ICM20602_SCAN_GYRO_Y, 290 INV_ICM20602_SCAN_GYRO_Z, 291 INV_ICM20602_SCAN_TIMESTAMP, 292 }; 293 294 enum inv_mpu6050_filter_e { 295 INV_MPU6050_FILTER_256HZ_NOLPF2 = 0, 296 INV_MPU6050_FILTER_188HZ, 297 INV_MPU6050_FILTER_98HZ, 298 INV_MPU6050_FILTER_42HZ, 299 INV_MPU6050_FILTER_20HZ, 300 INV_MPU6050_FILTER_10HZ, 301 INV_MPU6050_FILTER_5HZ, 302 INV_MPU6050_FILTER_2100HZ_NOLPF, 303 NUM_MPU6050_FILTER 304 }; 305 306 /* IIO attribute address */ 307 enum INV_MPU6050_IIO_ATTR_ADDR { 308 ATTR_GYRO_MATRIX, 309 ATTR_ACCL_MATRIX, 310 }; 311 312 enum inv_mpu6050_accl_fs_e { 313 INV_MPU6050_FS_02G = 0, 314 INV_MPU6050_FS_04G, 315 INV_MPU6050_FS_08G, 316 INV_MPU6050_FS_16G, 317 NUM_ACCL_FSR 318 }; 319 320 enum inv_mpu6050_fsr_e { 321 INV_MPU6050_FSR_250DPS = 0, 322 INV_MPU6050_FSR_500DPS, 323 INV_MPU6050_FSR_1000DPS, 324 INV_MPU6050_FSR_2000DPS, 325 NUM_MPU6050_FSR 326 }; 327 328 enum inv_mpu6050_clock_sel_e { 329 INV_CLK_INTERNAL = 0, 330 INV_CLK_PLL, 331 NUM_CLK 332 }; 333 334 irqreturn_t inv_mpu6050_read_fifo(int irq, void *p); 335 int inv_mpu6050_probe_trigger(struct iio_dev *indio_dev, int irq_type); 336 int inv_reset_fifo(struct iio_dev *indio_dev); 337 int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, u32 mask); 338 int inv_mpu6050_write_reg(struct inv_mpu6050_state *st, int reg, u8 val); 339 int inv_mpu6050_set_power_itg(struct inv_mpu6050_state *st, bool power_on); 340 int inv_mpu_acpi_create_mux_client(struct i2c_client *client); 341 void inv_mpu_acpi_delete_mux_client(struct i2c_client *client); 342 int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name, 343 int (*inv_mpu_bus_setup)(struct iio_dev *), int chip_type); 344 extern const struct dev_pm_ops inv_mpu_pmops; 345