1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * ccs811.c - Support for AMS CCS811 VOC Sensor 4 * 5 * Copyright (C) 2017 Narcisa Vasile <narcisaanamaria12@gmail.com> 6 * 7 * Datasheet: ams.com/content/download/951091/2269479/CCS811_DS000459_3-00.pdf 8 * 9 * IIO driver for AMS CCS811 (I2C address 0x5A/0x5B set by ADDR Low/High) 10 * 11 * TODO: 12 * 1. Make the drive mode selectable form userspace 13 * 2. Add support for interrupts 14 * 3. Adjust time to wait for data to be ready based on selected operation mode 15 * 4. Read error register and put the information in logs 16 */ 17 18 #include <linux/delay.h> 19 #include <linux/gpio/consumer.h> 20 #include <linux/i2c.h> 21 #include <linux/iio/iio.h> 22 #include <linux/iio/buffer.h> 23 #include <linux/iio/trigger.h> 24 #include <linux/iio/triggered_buffer.h> 25 #include <linux/iio/trigger_consumer.h> 26 #include <linux/module.h> 27 28 #define CCS811_STATUS 0x00 29 #define CCS811_MEAS_MODE 0x01 30 #define CCS811_ALG_RESULT_DATA 0x02 31 #define CCS811_RAW_DATA 0x03 32 #define CCS811_HW_ID 0x20 33 #define CCS811_HW_ID_VALUE 0x81 34 #define CCS811_HW_VERSION 0x21 35 #define CCS811_HW_VERSION_VALUE 0x10 36 #define CCS811_HW_VERSION_MASK 0xF0 37 #define CCS811_ERR 0xE0 38 /* Used to transition from boot to application mode */ 39 #define CCS811_APP_START 0xF4 40 #define CCS811_SW_RESET 0xFF 41 42 /* Status register flags */ 43 #define CCS811_STATUS_ERROR BIT(0) 44 #define CCS811_STATUS_DATA_READY BIT(3) 45 #define CCS811_STATUS_APP_VALID_MASK BIT(4) 46 #define CCS811_STATUS_APP_VALID_LOADED BIT(4) 47 /* 48 * Value of FW_MODE bit of STATUS register describes the sensor's state: 49 * 0: Firmware is in boot mode, this allows new firmware to be loaded 50 * 1: Firmware is in application mode. CCS811 is ready to take ADC measurements 51 */ 52 #define CCS811_STATUS_FW_MODE_MASK BIT(7) 53 #define CCS811_STATUS_FW_MODE_APPLICATION BIT(7) 54 55 /* Measurement modes */ 56 #define CCS811_MODE_IDLE 0x00 57 #define CCS811_MODE_IAQ_1SEC 0x10 58 #define CCS811_MODE_IAQ_10SEC 0x20 59 #define CCS811_MODE_IAQ_60SEC 0x30 60 #define CCS811_MODE_RAW_DATA 0x40 61 62 #define CCS811_MEAS_MODE_INTERRUPT BIT(3) 63 64 #define CCS811_VOLTAGE_MASK 0x3FF 65 66 struct ccs811_reading { 67 __be16 co2; 68 __be16 voc; 69 u8 status; 70 u8 error; 71 __be16 raw_data; 72 } __attribute__((__packed__)); 73 74 struct ccs811_data { 75 struct i2c_client *client; 76 struct mutex lock; /* Protect readings */ 77 struct ccs811_reading buffer; 78 struct iio_trigger *drdy_trig; 79 struct gpio_desc *wakeup_gpio; 80 bool drdy_trig_on; 81 /* Ensures correct alignment of timestamp if present */ 82 struct { 83 s16 channels[2]; 84 s64 ts __aligned(8); 85 } scan; 86 }; 87 88 static const struct iio_chan_spec ccs811_channels[] = { 89 { 90 .type = IIO_CURRENT, 91 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 92 BIT(IIO_CHAN_INFO_SCALE), 93 .scan_index = -1, 94 }, { 95 .type = IIO_VOLTAGE, 96 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 97 BIT(IIO_CHAN_INFO_SCALE), 98 .scan_index = -1, 99 }, { 100 .type = IIO_CONCENTRATION, 101 .channel2 = IIO_MOD_CO2, 102 .modified = 1, 103 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 104 BIT(IIO_CHAN_INFO_SCALE), 105 .scan_index = 0, 106 .scan_type = { 107 .sign = 'u', 108 .realbits = 16, 109 .storagebits = 16, 110 .endianness = IIO_BE, 111 }, 112 }, { 113 .type = IIO_CONCENTRATION, 114 .channel2 = IIO_MOD_VOC, 115 .modified = 1, 116 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 117 BIT(IIO_CHAN_INFO_SCALE), 118 .scan_index = 1, 119 .scan_type = { 120 .sign = 'u', 121 .realbits = 16, 122 .storagebits = 16, 123 .endianness = IIO_BE, 124 }, 125 }, 126 IIO_CHAN_SOFT_TIMESTAMP(2), 127 }; 128 129 /* 130 * The CCS811 powers-up in boot mode. A setup write to CCS811_APP_START will 131 * transition the sensor to application mode. 132 */ 133 static int ccs811_start_sensor_application(struct i2c_client *client) 134 { 135 int ret; 136 137 ret = i2c_smbus_read_byte_data(client, CCS811_STATUS); 138 if (ret < 0) 139 return ret; 140 141 if ((ret & CCS811_STATUS_FW_MODE_APPLICATION)) 142 return 0; 143 144 if ((ret & CCS811_STATUS_APP_VALID_MASK) != 145 CCS811_STATUS_APP_VALID_LOADED) 146 return -EIO; 147 148 ret = i2c_smbus_write_byte(client, CCS811_APP_START); 149 if (ret < 0) 150 return ret; 151 152 ret = i2c_smbus_read_byte_data(client, CCS811_STATUS); 153 if (ret < 0) 154 return ret; 155 156 if ((ret & CCS811_STATUS_FW_MODE_MASK) != 157 CCS811_STATUS_FW_MODE_APPLICATION) { 158 dev_err(&client->dev, "Application failed to start. Sensor is still in boot mode.\n"); 159 return -EIO; 160 } 161 162 return 0; 163 } 164 165 static int ccs811_setup(struct i2c_client *client) 166 { 167 int ret; 168 169 ret = ccs811_start_sensor_application(client); 170 if (ret < 0) 171 return ret; 172 173 return i2c_smbus_write_byte_data(client, CCS811_MEAS_MODE, 174 CCS811_MODE_IAQ_1SEC); 175 } 176 177 static void ccs811_set_wakeup(struct ccs811_data *data, bool enable) 178 { 179 if (!data->wakeup_gpio) 180 return; 181 182 gpiod_set_value(data->wakeup_gpio, enable); 183 184 if (enable) 185 usleep_range(50, 60); 186 else 187 usleep_range(20, 30); 188 } 189 190 static int ccs811_get_measurement(struct ccs811_data *data) 191 { 192 int ret, tries = 11; 193 194 ccs811_set_wakeup(data, true); 195 196 /* Maximum waiting time: 1s, as measurements are made every second */ 197 while (tries-- > 0) { 198 ret = i2c_smbus_read_byte_data(data->client, CCS811_STATUS); 199 if (ret < 0) 200 return ret; 201 202 if ((ret & CCS811_STATUS_DATA_READY) || tries == 0) 203 break; 204 msleep(100); 205 } 206 if (!(ret & CCS811_STATUS_DATA_READY)) 207 return -EIO; 208 209 ret = i2c_smbus_read_i2c_block_data(data->client, 210 CCS811_ALG_RESULT_DATA, 8, 211 (char *)&data->buffer); 212 ccs811_set_wakeup(data, false); 213 214 return ret; 215 } 216 217 static int ccs811_read_raw(struct iio_dev *indio_dev, 218 struct iio_chan_spec const *chan, 219 int *val, int *val2, long mask) 220 { 221 struct ccs811_data *data = iio_priv(indio_dev); 222 int ret; 223 224 switch (mask) { 225 case IIO_CHAN_INFO_RAW: 226 ret = iio_device_claim_direct_mode(indio_dev); 227 if (ret) 228 return ret; 229 mutex_lock(&data->lock); 230 ret = ccs811_get_measurement(data); 231 if (ret < 0) { 232 mutex_unlock(&data->lock); 233 iio_device_release_direct_mode(indio_dev); 234 return ret; 235 } 236 237 switch (chan->type) { 238 case IIO_VOLTAGE: 239 *val = be16_to_cpu(data->buffer.raw_data) & 240 CCS811_VOLTAGE_MASK; 241 ret = IIO_VAL_INT; 242 break; 243 case IIO_CURRENT: 244 *val = be16_to_cpu(data->buffer.raw_data) >> 10; 245 ret = IIO_VAL_INT; 246 break; 247 case IIO_CONCENTRATION: 248 switch (chan->channel2) { 249 case IIO_MOD_CO2: 250 *val = be16_to_cpu(data->buffer.co2); 251 ret = IIO_VAL_INT; 252 break; 253 case IIO_MOD_VOC: 254 *val = be16_to_cpu(data->buffer.voc); 255 ret = IIO_VAL_INT; 256 break; 257 default: 258 ret = -EINVAL; 259 } 260 break; 261 default: 262 ret = -EINVAL; 263 } 264 mutex_unlock(&data->lock); 265 iio_device_release_direct_mode(indio_dev); 266 267 return ret; 268 269 case IIO_CHAN_INFO_SCALE: 270 switch (chan->type) { 271 case IIO_VOLTAGE: 272 *val = 1; 273 *val2 = 612903; 274 return IIO_VAL_INT_PLUS_MICRO; 275 case IIO_CURRENT: 276 *val = 0; 277 *val2 = 1000; 278 return IIO_VAL_INT_PLUS_MICRO; 279 case IIO_CONCENTRATION: 280 switch (chan->channel2) { 281 case IIO_MOD_CO2: 282 *val = 0; 283 *val2 = 100; 284 return IIO_VAL_INT_PLUS_MICRO; 285 case IIO_MOD_VOC: 286 *val = 0; 287 *val2 = 100; 288 return IIO_VAL_INT_PLUS_NANO; 289 default: 290 return -EINVAL; 291 } 292 default: 293 return -EINVAL; 294 } 295 default: 296 return -EINVAL; 297 } 298 } 299 300 static const struct iio_info ccs811_info = { 301 .read_raw = ccs811_read_raw, 302 }; 303 304 static int ccs811_set_trigger_state(struct iio_trigger *trig, 305 bool state) 306 { 307 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 308 struct ccs811_data *data = iio_priv(indio_dev); 309 int ret; 310 311 ret = i2c_smbus_read_byte_data(data->client, CCS811_MEAS_MODE); 312 if (ret < 0) 313 return ret; 314 315 if (state) 316 ret |= CCS811_MEAS_MODE_INTERRUPT; 317 else 318 ret &= ~CCS811_MEAS_MODE_INTERRUPT; 319 320 data->drdy_trig_on = state; 321 322 return i2c_smbus_write_byte_data(data->client, CCS811_MEAS_MODE, ret); 323 } 324 325 static const struct iio_trigger_ops ccs811_trigger_ops = { 326 .set_trigger_state = ccs811_set_trigger_state, 327 }; 328 329 static irqreturn_t ccs811_trigger_handler(int irq, void *p) 330 { 331 struct iio_poll_func *pf = p; 332 struct iio_dev *indio_dev = pf->indio_dev; 333 struct ccs811_data *data = iio_priv(indio_dev); 334 struct i2c_client *client = data->client; 335 int ret; 336 337 ret = i2c_smbus_read_i2c_block_data(client, CCS811_ALG_RESULT_DATA, 338 sizeof(data->scan.channels), 339 (u8 *)data->scan.channels); 340 if (ret != 4) { 341 dev_err(&client->dev, "cannot read sensor data\n"); 342 goto err; 343 } 344 345 iio_push_to_buffers_with_timestamp(indio_dev, &data->scan, 346 iio_get_time_ns(indio_dev)); 347 348 err: 349 iio_trigger_notify_done(indio_dev->trig); 350 351 return IRQ_HANDLED; 352 } 353 354 static irqreturn_t ccs811_data_rdy_trigger_poll(int irq, void *private) 355 { 356 struct iio_dev *indio_dev = private; 357 struct ccs811_data *data = iio_priv(indio_dev); 358 359 if (data->drdy_trig_on) 360 iio_trigger_poll(data->drdy_trig); 361 362 return IRQ_HANDLED; 363 } 364 365 static int ccs811_reset(struct i2c_client *client) 366 { 367 struct gpio_desc *reset_gpio; 368 int ret; 369 370 reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", 371 GPIOD_OUT_LOW); 372 if (IS_ERR(reset_gpio)) 373 return PTR_ERR(reset_gpio); 374 375 /* Try to reset using nRESET pin if available else do SW reset */ 376 if (reset_gpio) { 377 gpiod_set_value(reset_gpio, 1); 378 usleep_range(20, 30); 379 gpiod_set_value(reset_gpio, 0); 380 } else { 381 /* 382 * As per the datasheet, this sequence of values needs to be 383 * written to the SW_RESET register for triggering the soft 384 * reset in the device and placing it in boot mode. 385 */ 386 static const u8 reset_seq[] = { 387 0x11, 0xE5, 0x72, 0x8A, 388 }; 389 390 ret = i2c_smbus_write_i2c_block_data(client, CCS811_SW_RESET, 391 sizeof(reset_seq), reset_seq); 392 if (ret < 0) { 393 dev_err(&client->dev, "Failed to reset sensor\n"); 394 return ret; 395 } 396 } 397 398 /* tSTART delay required after reset */ 399 usleep_range(1000, 2000); 400 401 return 0; 402 } 403 404 static int ccs811_probe(struct i2c_client *client) 405 { 406 const struct i2c_device_id *id = i2c_client_get_device_id(client); 407 struct iio_dev *indio_dev; 408 struct ccs811_data *data; 409 int ret; 410 411 if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WRITE_BYTE 412 | I2C_FUNC_SMBUS_BYTE_DATA 413 | I2C_FUNC_SMBUS_READ_I2C_BLOCK)) 414 return -EOPNOTSUPP; 415 416 indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); 417 if (!indio_dev) 418 return -ENOMEM; 419 420 data = iio_priv(indio_dev); 421 i2c_set_clientdata(client, indio_dev); 422 data->client = client; 423 424 data->wakeup_gpio = devm_gpiod_get_optional(&client->dev, "wakeup", 425 GPIOD_OUT_HIGH); 426 if (IS_ERR(data->wakeup_gpio)) 427 return PTR_ERR(data->wakeup_gpio); 428 429 ccs811_set_wakeup(data, true); 430 431 ret = ccs811_reset(client); 432 if (ret) { 433 ccs811_set_wakeup(data, false); 434 return ret; 435 } 436 437 /* Check hardware id (should be 0x81 for this family of devices) */ 438 ret = i2c_smbus_read_byte_data(client, CCS811_HW_ID); 439 if (ret < 0) { 440 ccs811_set_wakeup(data, false); 441 return ret; 442 } 443 444 if (ret != CCS811_HW_ID_VALUE) { 445 dev_err(&client->dev, "hardware id doesn't match CCS81x\n"); 446 ccs811_set_wakeup(data, false); 447 return -ENODEV; 448 } 449 450 ret = i2c_smbus_read_byte_data(client, CCS811_HW_VERSION); 451 if (ret < 0) { 452 ccs811_set_wakeup(data, false); 453 return ret; 454 } 455 456 if ((ret & CCS811_HW_VERSION_MASK) != CCS811_HW_VERSION_VALUE) { 457 dev_err(&client->dev, "no CCS811 sensor\n"); 458 ccs811_set_wakeup(data, false); 459 return -ENODEV; 460 } 461 462 ret = ccs811_setup(client); 463 if (ret < 0) { 464 ccs811_set_wakeup(data, false); 465 return ret; 466 } 467 468 ccs811_set_wakeup(data, false); 469 470 mutex_init(&data->lock); 471 472 indio_dev->name = id->name; 473 indio_dev->info = &ccs811_info; 474 indio_dev->modes = INDIO_DIRECT_MODE; 475 476 indio_dev->channels = ccs811_channels; 477 indio_dev->num_channels = ARRAY_SIZE(ccs811_channels); 478 479 if (client->irq > 0) { 480 ret = devm_request_threaded_irq(&client->dev, client->irq, 481 ccs811_data_rdy_trigger_poll, 482 NULL, 483 IRQF_TRIGGER_FALLING | 484 IRQF_ONESHOT, 485 "ccs811_irq", indio_dev); 486 if (ret) { 487 dev_err(&client->dev, "irq request error %d\n", -ret); 488 goto err_poweroff; 489 } 490 491 data->drdy_trig = devm_iio_trigger_alloc(&client->dev, 492 "%s-dev%d", 493 indio_dev->name, 494 iio_device_id(indio_dev)); 495 if (!data->drdy_trig) { 496 ret = -ENOMEM; 497 goto err_poweroff; 498 } 499 500 data->drdy_trig->ops = &ccs811_trigger_ops; 501 iio_trigger_set_drvdata(data->drdy_trig, indio_dev); 502 ret = iio_trigger_register(data->drdy_trig); 503 if (ret) 504 goto err_poweroff; 505 506 indio_dev->trig = iio_trigger_get(data->drdy_trig); 507 } 508 509 ret = iio_triggered_buffer_setup(indio_dev, NULL, 510 ccs811_trigger_handler, NULL); 511 512 if (ret < 0) { 513 dev_err(&client->dev, "triggered buffer setup failed\n"); 514 goto err_trigger_unregister; 515 } 516 517 ret = iio_device_register(indio_dev); 518 if (ret < 0) { 519 dev_err(&client->dev, "unable to register iio device\n"); 520 goto err_buffer_cleanup; 521 } 522 return 0; 523 524 err_buffer_cleanup: 525 iio_triggered_buffer_cleanup(indio_dev); 526 err_trigger_unregister: 527 if (data->drdy_trig) 528 iio_trigger_unregister(data->drdy_trig); 529 err_poweroff: 530 i2c_smbus_write_byte_data(client, CCS811_MEAS_MODE, CCS811_MODE_IDLE); 531 532 return ret; 533 } 534 535 static void ccs811_remove(struct i2c_client *client) 536 { 537 struct iio_dev *indio_dev = i2c_get_clientdata(client); 538 struct ccs811_data *data = iio_priv(indio_dev); 539 int ret; 540 541 iio_device_unregister(indio_dev); 542 iio_triggered_buffer_cleanup(indio_dev); 543 if (data->drdy_trig) 544 iio_trigger_unregister(data->drdy_trig); 545 546 ret = i2c_smbus_write_byte_data(client, CCS811_MEAS_MODE, 547 CCS811_MODE_IDLE); 548 if (ret) 549 dev_warn(&client->dev, "Failed to power down device (%pe)\n", 550 ERR_PTR(ret)); 551 } 552 553 static const struct i2c_device_id ccs811_id[] = { 554 {"ccs811", 0}, 555 { } 556 }; 557 MODULE_DEVICE_TABLE(i2c, ccs811_id); 558 559 static const struct of_device_id ccs811_dt_ids[] = { 560 { .compatible = "ams,ccs811" }, 561 { } 562 }; 563 MODULE_DEVICE_TABLE(of, ccs811_dt_ids); 564 565 static struct i2c_driver ccs811_driver = { 566 .driver = { 567 .name = "ccs811", 568 .of_match_table = ccs811_dt_ids, 569 }, 570 .probe_new = ccs811_probe, 571 .remove = ccs811_remove, 572 .id_table = ccs811_id, 573 }; 574 module_i2c_driver(ccs811_driver); 575 576 MODULE_AUTHOR("Narcisa Vasile <narcisaanamaria12@gmail.com>"); 577 MODULE_DESCRIPTION("CCS811 volatile organic compounds sensor"); 578 MODULE_LICENSE("GPL v2"); 579