1 /* 2 * Qualcomm PM8xxx PMIC XOADC driver 3 * 4 * These ADCs are known as HK/XO (house keeping / chrystal oscillator) 5 * "XO" in "XOADC" means Chrystal Oscillator. It's a bunch of 6 * specific-purpose and general purpose ADC converters and channels. 7 * 8 * Copyright (C) 2017 Linaro Ltd. 9 * Author: Linus Walleij <linus.walleij@linaro.org> 10 */ 11 12 #include <linux/iio/iio.h> 13 #include <linux/iio/sysfs.h> 14 #include <linux/module.h> 15 #include <linux/of.h> 16 #include <linux/of_device.h> 17 #include <linux/platform_device.h> 18 #include <linux/regmap.h> 19 #include <linux/init.h> 20 #include <linux/interrupt.h> 21 #include <linux/regulator/consumer.h> 22 23 #include "qcom-vadc-common.h" 24 25 /* 26 * Definitions for the "user processor" registers lifted from the v3.4 27 * Qualcomm tree. Their kernel has two out-of-tree drivers for the ADC: 28 * drivers/misc/pmic8058-xoadc.c 29 * drivers/hwmon/pm8xxx-adc.c 30 * None of them contain any complete register specification, so this is 31 * a best effort of combining the information. 32 */ 33 34 /* These appear to be "battery monitor" registers */ 35 #define ADC_ARB_BTM_CNTRL1 0x17e 36 #define ADC_ARB_BTM_CNTRL1_EN_BTM BIT(0) 37 #define ADC_ARB_BTM_CNTRL1_SEL_OP_MODE BIT(1) 38 #define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL1 BIT(2) 39 #define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL2 BIT(3) 40 #define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL3 BIT(4) 41 #define ADC_ARB_BTM_CNTRL1_MEAS_INTERVAL4 BIT(5) 42 #define ADC_ARB_BTM_CNTRL1_EOC BIT(6) 43 #define ADC_ARB_BTM_CNTRL1_REQ BIT(7) 44 45 #define ADC_ARB_BTM_AMUX_CNTRL 0x17f 46 #define ADC_ARB_BTM_ANA_PARAM 0x180 47 #define ADC_ARB_BTM_DIG_PARAM 0x181 48 #define ADC_ARB_BTM_RSV 0x182 49 #define ADC_ARB_BTM_DATA1 0x183 50 #define ADC_ARB_BTM_DATA0 0x184 51 #define ADC_ARB_BTM_BAT_COOL_THR1 0x185 52 #define ADC_ARB_BTM_BAT_COOL_THR0 0x186 53 #define ADC_ARB_BTM_BAT_WARM_THR1 0x187 54 #define ADC_ARB_BTM_BAT_WARM_THR0 0x188 55 #define ADC_ARB_BTM_CNTRL2 0x18c 56 57 /* Proper ADC registers */ 58 59 #define ADC_ARB_USRP_CNTRL 0x197 60 #define ADC_ARB_USRP_CNTRL_EN_ARB BIT(0) 61 #define ADC_ARB_USRP_CNTRL_RSV1 BIT(1) 62 #define ADC_ARB_USRP_CNTRL_RSV2 BIT(2) 63 #define ADC_ARB_USRP_CNTRL_RSV3 BIT(3) 64 #define ADC_ARB_USRP_CNTRL_RSV4 BIT(4) 65 #define ADC_ARB_USRP_CNTRL_RSV5 BIT(5) 66 #define ADC_ARB_USRP_CNTRL_EOC BIT(6) 67 #define ADC_ARB_USRP_CNTRL_REQ BIT(7) 68 69 #define ADC_ARB_USRP_AMUX_CNTRL 0x198 70 /* 71 * The channel mask includes the bits selecting channel mux and prescaler 72 * on PM8058, or channel mux and premux on PM8921. 73 */ 74 #define ADC_ARB_USRP_AMUX_CNTRL_CHAN_MASK 0xfc 75 #define ADC_ARB_USRP_AMUX_CNTRL_RSV0 BIT(0) 76 #define ADC_ARB_USRP_AMUX_CNTRL_RSV1 BIT(1) 77 /* On PM8058 this is prescaling, on PM8921 this is premux */ 78 #define ADC_ARB_USRP_AMUX_CNTRL_PRESCALEMUX0 BIT(2) 79 #define ADC_ARB_USRP_AMUX_CNTRL_PRESCALEMUX1 BIT(3) 80 #define ADC_ARB_USRP_AMUX_CNTRL_SEL0 BIT(4) 81 #define ADC_ARB_USRP_AMUX_CNTRL_SEL1 BIT(5) 82 #define ADC_ARB_USRP_AMUX_CNTRL_SEL2 BIT(6) 83 #define ADC_ARB_USRP_AMUX_CNTRL_SEL3 BIT(7) 84 #define ADC_AMUX_PREMUX_SHIFT 2 85 #define ADC_AMUX_SEL_SHIFT 4 86 87 /* We know very little about the bits in this register */ 88 #define ADC_ARB_USRP_ANA_PARAM 0x199 89 #define ADC_ARB_USRP_ANA_PARAM_DIS 0xFE 90 #define ADC_ARB_USRP_ANA_PARAM_EN 0xFF 91 92 #define ADC_ARB_USRP_DIG_PARAM 0x19A 93 #define ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT0 BIT(0) 94 #define ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT1 BIT(1) 95 #define ADC_ARB_USRP_DIG_PARAM_CLK_RATE0 BIT(2) 96 #define ADC_ARB_USRP_DIG_PARAM_CLK_RATE1 BIT(3) 97 #define ADC_ARB_USRP_DIG_PARAM_EOC BIT(4) 98 /* 99 * On a later ADC the decimation factors are defined as 100 * 00 = 512, 01 = 1024, 10 = 2048, 11 = 4096 so assume this 101 * holds also for this older XOADC. 102 */ 103 #define ADC_ARB_USRP_DIG_PARAM_DEC_RATE0 BIT(5) 104 #define ADC_ARB_USRP_DIG_PARAM_DEC_RATE1 BIT(6) 105 #define ADC_ARB_USRP_DIG_PARAM_EN BIT(7) 106 #define ADC_DIG_PARAM_DEC_SHIFT 5 107 108 #define ADC_ARB_USRP_RSV 0x19B 109 #define ADC_ARB_USRP_RSV_RST BIT(0) 110 #define ADC_ARB_USRP_RSV_DTEST0 BIT(1) 111 #define ADC_ARB_USRP_RSV_DTEST1 BIT(2) 112 #define ADC_ARB_USRP_RSV_OP BIT(3) 113 #define ADC_ARB_USRP_RSV_IP_SEL0 BIT(4) 114 #define ADC_ARB_USRP_RSV_IP_SEL1 BIT(5) 115 #define ADC_ARB_USRP_RSV_IP_SEL2 BIT(6) 116 #define ADC_ARB_USRP_RSV_TRM BIT(7) 117 #define ADC_RSV_IP_SEL_SHIFT 4 118 119 #define ADC_ARB_USRP_DATA0 0x19D 120 #define ADC_ARB_USRP_DATA1 0x19C 121 122 /** 123 * Physical channels which MUST exist on all PM variants in order to provide 124 * proper reference points for calibration. 125 * 126 * @PM8XXX_CHANNEL_INTERNAL: 625mV reference channel 127 * @PM8XXX_CHANNEL_125V: 1250mV reference channel 128 * @PM8XXX_CHANNEL_INTERNAL_2: 325mV reference channel 129 * @PM8XXX_CHANNEL_MUXOFF: channel to reduce input load on mux, apparently also 130 * measures XO temperature 131 */ 132 #define PM8XXX_CHANNEL_INTERNAL 0x0c 133 #define PM8XXX_CHANNEL_125V 0x0d 134 #define PM8XXX_CHANNEL_INTERNAL_2 0x0e 135 #define PM8XXX_CHANNEL_MUXOFF 0x0f 136 137 /* 138 * PM8058 AMUX premux scaling, two bits. This is done of the channel before 139 * reaching the AMUX. 140 */ 141 #define PM8058_AMUX_PRESCALE_0 0x0 /* No scaling on the signal */ 142 #define PM8058_AMUX_PRESCALE_1 0x1 /* Unity scaling selected by the user */ 143 #define PM8058_AMUX_PRESCALE_1_DIV3 0x2 /* 1/3 prescaler on the input */ 144 145 /* Defines reference voltage for the XOADC */ 146 #define AMUX_RSV0 0x0 /* XO_IN/XOADC_GND, special selection to read XO temp */ 147 #define AMUX_RSV1 0x1 /* PMIC_IN/XOADC_GND */ 148 #define AMUX_RSV2 0x2 /* PMIC_IN/BMS_CSP */ 149 #define AMUX_RSV3 0x3 /* not used */ 150 #define AMUX_RSV4 0x4 /* XOADC_GND/XOADC_GND */ 151 #define AMUX_RSV5 0x5 /* XOADC_VREF/XOADC_GND */ 152 #define XOADC_RSV_MAX 5 /* 3 bits 0..7, 3 and 6,7 are invalid */ 153 154 /** 155 * struct xoadc_channel - encodes channel properties and defaults 156 * @datasheet_name: the hardwarename of this channel 157 * @pre_scale_mux: prescale (PM8058) or premux (PM8921) for selecting 158 * this channel. Both this and the amux channel is needed to uniquely 159 * identify a channel. Values 0..3. 160 * @amux_channel: value of the ADC_ARB_USRP_AMUX_CNTRL register for this 161 * channel, bits 4..7, selects the amux, values 0..f 162 * @prescale: the channels have hard-coded prescale ratios defined 163 * by the hardware, this tells us what it is 164 * @type: corresponding IIO channel type, usually IIO_VOLTAGE or 165 * IIO_TEMP 166 * @scale_fn_type: the liner interpolation etc to convert the 167 * ADC code to the value that IIO expects, in uV or millicelsius 168 * etc. This scale function can be pretty elaborate if different 169 * thermistors are connected or other hardware characteristics are 170 * deployed. 171 * @amux_ip_rsv: ratiometric scale value used by the analog muxer: this 172 * selects the reference voltage for ratiometric scaling 173 */ 174 struct xoadc_channel { 175 const char *datasheet_name; 176 u8 pre_scale_mux:2; 177 u8 amux_channel:4; 178 const struct vadc_prescale_ratio prescale; 179 enum iio_chan_type type; 180 enum vadc_scale_fn_type scale_fn_type; 181 u8 amux_ip_rsv:3; 182 }; 183 184 /** 185 * struct xoadc_variant - encodes the XOADC variant characteristics 186 * @name: name of this PMIC variant 187 * @channels: the hardware channels and respective settings and defaults 188 * @broken_ratiometric: if the PMIC has broken ratiometric scaling (this 189 * is a known problem on PM8058) 190 * @prescaling: this variant uses AMUX bits 2 & 3 for prescaling (PM8058) 191 * @second_level_mux: this variant uses AMUX bits 2 & 3 for a second level 192 * mux 193 */ 194 struct xoadc_variant { 195 const char name[16]; 196 const struct xoadc_channel *channels; 197 bool broken_ratiometric; 198 bool prescaling; 199 bool second_level_mux; 200 }; 201 202 /* 203 * XOADC_CHAN macro parameters: 204 * _dname: the name of the channel 205 * _presmux: prescaler (PM8058) or premux (PM8921) setting for this channel 206 * _amux: the value in bits 2..7 of the ADC_ARB_USRP_AMUX_CNTRL register 207 * for this channel. On some PMICs some of the bits select a prescaler, and 208 * on some PMICs some of the bits select various complex multiplex settings. 209 * _type: IIO channel type 210 * _prenum: prescaler numerator (dividend) 211 * _preden: prescaler denominator (divisor) 212 * _scale: scaling function type, this selects how the raw valued is mangled 213 * to output the actual processed measurement 214 * _amip: analog mux input parent when using ratiometric measurements 215 */ 216 #define XOADC_CHAN(_dname, _presmux, _amux, _type, _prenum, _preden, _scale, _amip) \ 217 { \ 218 .datasheet_name = __stringify(_dname), \ 219 .pre_scale_mux = _presmux, \ 220 .amux_channel = _amux, \ 221 .prescale = { .num = _prenum, .den = _preden }, \ 222 .type = _type, \ 223 .scale_fn_type = _scale, \ 224 .amux_ip_rsv = _amip, \ 225 } 226 227 /* 228 * Taken from arch/arm/mach-msm/board-9615.c in the vendor tree: 229 * TODO: incomplete, needs testing. 230 */ 231 static const struct xoadc_channel pm8018_xoadc_channels[] = { 232 XOADC_CHAN(VCOIN, 0x00, 0x00, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 233 XOADC_CHAN(VBAT, 0x00, 0x01, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 234 XOADC_CHAN(VPH_PWR, 0x00, 0x02, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 235 XOADC_CHAN(DIE_TEMP, 0x00, 0x0b, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1), 236 /* Used for battery ID or battery temperature */ 237 XOADC_CHAN(AMUX8, 0x00, 0x08, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV2), 238 XOADC_CHAN(INTERNAL, 0x00, 0x0c, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 239 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 240 XOADC_CHAN(MUXOFF, 0x00, 0x0f, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0), 241 { }, /* Sentinel */ 242 }; 243 244 /* 245 * Taken from arch/arm/mach-msm/board-8930-pmic.c in the vendor tree: 246 * TODO: needs testing. 247 */ 248 static const struct xoadc_channel pm8038_xoadc_channels[] = { 249 XOADC_CHAN(VCOIN, 0x00, 0x00, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 250 XOADC_CHAN(VBAT, 0x00, 0x01, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 251 XOADC_CHAN(DCIN, 0x00, 0x02, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1), 252 XOADC_CHAN(ICHG, 0x00, 0x03, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 253 XOADC_CHAN(VPH_PWR, 0x00, 0x04, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 254 XOADC_CHAN(AMUX5, 0x00, 0x05, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 255 XOADC_CHAN(AMUX6, 0x00, 0x06, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 256 XOADC_CHAN(AMUX7, 0x00, 0x07, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 257 /* AMUX8 used for battery temperature in most cases */ 258 XOADC_CHAN(AMUX8, 0x00, 0x08, IIO_TEMP, 1, 1, SCALE_THERM_100K_PULLUP, AMUX_RSV2), 259 XOADC_CHAN(AMUX9, 0x00, 0x09, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 260 XOADC_CHAN(USB_VBUS, 0x00, 0x0a, IIO_VOLTAGE, 1, 4, SCALE_DEFAULT, AMUX_RSV1), 261 XOADC_CHAN(DIE_TEMP, 0x00, 0x0b, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1), 262 XOADC_CHAN(INTERNAL, 0x00, 0x0c, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 263 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 264 XOADC_CHAN(INTERNAL_2, 0x00, 0x0e, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 265 XOADC_CHAN(MUXOFF, 0x00, 0x0f, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0), 266 { }, /* Sentinel */ 267 }; 268 269 /* 270 * This was created by cross-referencing the vendor tree 271 * arch/arm/mach-msm/board-msm8x60.c msm_adc_channels_data[] 272 * with the "channel types" (first field) to find the right 273 * configuration for these channels on an MSM8x60 i.e. PM8058 274 * setup. 275 */ 276 static const struct xoadc_channel pm8058_xoadc_channels[] = { 277 XOADC_CHAN(VCOIN, 0x00, 0x00, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1), 278 XOADC_CHAN(VBAT, 0x00, 0x01, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 279 XOADC_CHAN(DCIN, 0x00, 0x02, IIO_VOLTAGE, 1, 10, SCALE_DEFAULT, AMUX_RSV1), 280 XOADC_CHAN(ICHG, 0x00, 0x03, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 281 XOADC_CHAN(VPH_PWR, 0x00, 0x04, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 282 /* 283 * AMUX channels 5 thru 9 are referred to as MPP5 thru MPP9 in 284 * some code and documentation. But they are really just 5 285 * channels just like any other. They are connected to a switching 286 * matrix where they can be routed to any of the MPPs, not just 287 * 1-to-1 onto MPP5 thru 9, so naming them MPP5 thru MPP9 is 288 * very confusing. 289 */ 290 XOADC_CHAN(AMUX5, 0x00, 0x05, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 291 XOADC_CHAN(AMUX6, 0x00, 0x06, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 292 XOADC_CHAN(AMUX7, 0x00, 0x07, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1), 293 XOADC_CHAN(AMUX8, 0x00, 0x08, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1), 294 XOADC_CHAN(AMUX9, 0x00, 0x09, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 295 XOADC_CHAN(USB_VBUS, 0x00, 0x0a, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 296 XOADC_CHAN(DIE_TEMP, 0x00, 0x0b, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1), 297 XOADC_CHAN(INTERNAL, 0x00, 0x0c, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 298 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 299 XOADC_CHAN(INTERNAL_2, 0x00, 0x0e, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 300 XOADC_CHAN(MUXOFF, 0x00, 0x0f, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0), 301 /* There are also "unity" and divided by 3 channels (prescaler) but noone is using them */ 302 { }, /* Sentinel */ 303 }; 304 305 /* 306 * The PM8921 has some pre-muxing on its channels, this comes from the vendor tree 307 * include/linux/mfd/pm8xxx/pm8xxx-adc.h 308 * board-flo-pmic.c (Nexus 7) and board-8064-pmic.c 309 */ 310 static const struct xoadc_channel pm8921_xoadc_channels[] = { 311 XOADC_CHAN(VCOIN, 0x00, 0x00, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 312 XOADC_CHAN(VBAT, 0x00, 0x01, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 313 XOADC_CHAN(DCIN, 0x00, 0x02, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1), 314 /* channel "ICHG" is reserved and not used on PM8921 */ 315 XOADC_CHAN(VPH_PWR, 0x00, 0x04, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 316 XOADC_CHAN(IBAT, 0x00, 0x05, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 317 /* CHAN 6 & 7 (MPP1 & MPP2) are reserved for MPP channels on PM8921 */ 318 XOADC_CHAN(BATT_THERM, 0x00, 0x08, IIO_TEMP, 1, 1, SCALE_THERM_100K_PULLUP, AMUX_RSV1), 319 XOADC_CHAN(BATT_ID, 0x00, 0x09, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 320 XOADC_CHAN(USB_VBUS, 0x00, 0x0a, IIO_VOLTAGE, 1, 4, SCALE_DEFAULT, AMUX_RSV1), 321 XOADC_CHAN(DIE_TEMP, 0x00, 0x0b, IIO_TEMP, 1, 1, SCALE_PMIC_THERM, AMUX_RSV1), 322 XOADC_CHAN(INTERNAL, 0x00, 0x0c, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 323 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 324 /* FIXME: look into the scaling of this temperature */ 325 XOADC_CHAN(CHG_TEMP, 0x00, 0x0e, IIO_TEMP, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 326 XOADC_CHAN(MUXOFF, 0x00, 0x0f, IIO_TEMP, 1, 1, SCALE_XOTHERM, AMUX_RSV0), 327 /* The following channels have premux bit 0 set to 1 (all end in 4) */ 328 XOADC_CHAN(ATEST_8, 0x01, 0x00, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 329 /* Set scaling to 1/2 based on the name for these two */ 330 XOADC_CHAN(USB_SNS_DIV20, 0x01, 0x01, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1), 331 XOADC_CHAN(DCIN_SNS_DIV20, 0x01, 0x02, IIO_VOLTAGE, 1, 2, SCALE_DEFAULT, AMUX_RSV1), 332 XOADC_CHAN(AMUX3, 0x01, 0x03, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 333 XOADC_CHAN(AMUX4, 0x01, 0x04, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 334 XOADC_CHAN(AMUX5, 0x01, 0x05, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 335 XOADC_CHAN(AMUX6, 0x01, 0x06, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 336 XOADC_CHAN(AMUX7, 0x01, 0x07, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 337 XOADC_CHAN(AMUX8, 0x01, 0x08, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 338 /* Internal test signals, I think */ 339 XOADC_CHAN(ATEST_1, 0x01, 0x09, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 340 XOADC_CHAN(ATEST_2, 0x01, 0x0a, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 341 XOADC_CHAN(ATEST_3, 0x01, 0x0b, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 342 XOADC_CHAN(ATEST_4, 0x01, 0x0c, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 343 XOADC_CHAN(ATEST_5, 0x01, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 344 XOADC_CHAN(ATEST_6, 0x01, 0x0e, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 345 XOADC_CHAN(ATEST_7, 0x01, 0x0f, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1), 346 /* The following channels have premux bit 1 set to 1 (all end in 8) */ 347 /* I guess even ATEST8 will be divided by 3 here */ 348 XOADC_CHAN(ATEST_8, 0x02, 0x00, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 349 /* I guess div 2 div 3 becomes div 6 */ 350 XOADC_CHAN(USB_SNS_DIV20_DIV3, 0x02, 0x01, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1), 351 XOADC_CHAN(DCIN_SNS_DIV20_DIV3, 0x02, 0x02, IIO_VOLTAGE, 1, 6, SCALE_DEFAULT, AMUX_RSV1), 352 XOADC_CHAN(AMUX3_DIV3, 0x02, 0x03, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 353 XOADC_CHAN(AMUX4_DIV3, 0x02, 0x04, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 354 XOADC_CHAN(AMUX5_DIV3, 0x02, 0x05, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 355 XOADC_CHAN(AMUX6_DIV3, 0x02, 0x06, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 356 XOADC_CHAN(AMUX7_DIV3, 0x02, 0x07, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 357 XOADC_CHAN(AMUX8_DIV3, 0x02, 0x08, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 358 XOADC_CHAN(ATEST_1_DIV3, 0x02, 0x09, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 359 XOADC_CHAN(ATEST_2_DIV3, 0x02, 0x0a, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 360 XOADC_CHAN(ATEST_3_DIV3, 0x02, 0x0b, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 361 XOADC_CHAN(ATEST_4_DIV3, 0x02, 0x0c, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 362 XOADC_CHAN(ATEST_5_DIV3, 0x02, 0x0d, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 363 XOADC_CHAN(ATEST_6_DIV3, 0x02, 0x0e, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 364 XOADC_CHAN(ATEST_7_DIV3, 0x02, 0x0f, IIO_VOLTAGE, 1, 3, SCALE_DEFAULT, AMUX_RSV1), 365 { }, /* Sentinel */ 366 }; 367 368 /** 369 * struct pm8xxx_chan_info - ADC channel information 370 * @name: name of this channel 371 * @hwchan: pointer to hardware channel information (muxing & scaling settings) 372 * @calibration: whether to use absolute or ratiometric calibration 373 * @scale_fn_type: scaling function type 374 * @decimation: 0,1,2,3 375 * @amux_ip_rsv: ratiometric scale value if using ratiometric 376 * calibration: 0, 1, 2, 4, 5. 377 */ 378 struct pm8xxx_chan_info { 379 const char *name; 380 const struct xoadc_channel *hwchan; 381 enum vadc_calibration calibration; 382 u8 decimation:2; 383 u8 amux_ip_rsv:3; 384 }; 385 386 /** 387 * struct pm8xxx_xoadc - state container for the XOADC 388 * @dev: pointer to device 389 * @map: regmap to access registers 390 * @vref: reference voltage regulator 391 * characteristics of the channels, and sensible default settings 392 * @nchans: number of channels, configured by the device tree 393 * @chans: the channel information per-channel, configured by the device tree 394 * @iio_chans: IIO channel specifiers 395 * @graph: linear calibration parameters for absolute and 396 * ratiometric measurements 397 * @complete: completion to indicate end of conversion 398 * @lock: lock to restrict access to the hardware to one client at the time 399 */ 400 struct pm8xxx_xoadc { 401 struct device *dev; 402 struct regmap *map; 403 const struct xoadc_variant *variant; 404 struct regulator *vref; 405 unsigned int nchans; 406 struct pm8xxx_chan_info *chans; 407 struct iio_chan_spec *iio_chans; 408 struct vadc_linear_graph graph[2]; 409 struct completion complete; 410 struct mutex lock; 411 }; 412 413 static irqreturn_t pm8xxx_eoc_irq(int irq, void *d) 414 { 415 struct iio_dev *indio_dev = d; 416 struct pm8xxx_xoadc *adc = iio_priv(indio_dev); 417 418 complete(&adc->complete); 419 420 return IRQ_HANDLED; 421 } 422 423 static struct pm8xxx_chan_info * 424 pm8xxx_get_channel(struct pm8xxx_xoadc *adc, u8 chan) 425 { 426 struct pm8xxx_chan_info *ch; 427 int i; 428 429 for (i = 0; i < adc->nchans; i++) { 430 ch = &adc->chans[i]; 431 if (ch->hwchan->amux_channel == chan) 432 break; 433 } 434 if (i == adc->nchans) 435 return NULL; 436 437 return ch; 438 } 439 440 static int pm8xxx_read_channel_rsv(struct pm8xxx_xoadc *adc, 441 const struct pm8xxx_chan_info *ch, 442 u8 rsv, u16 *adc_code, 443 bool force_ratiometric) 444 { 445 int ret; 446 unsigned int val; 447 u8 rsvmask, rsvval; 448 u8 lsb, msb; 449 450 dev_dbg(adc->dev, "read channel \"%s\", amux %d, prescale/mux: %d, rsv %d\n", 451 ch->name, ch->hwchan->amux_channel, ch->hwchan->pre_scale_mux, rsv); 452 453 mutex_lock(&adc->lock); 454 455 /* Mux in this channel */ 456 val = ch->hwchan->amux_channel << ADC_AMUX_SEL_SHIFT; 457 val |= ch->hwchan->pre_scale_mux << ADC_AMUX_PREMUX_SHIFT; 458 ret = regmap_write(adc->map, ADC_ARB_USRP_AMUX_CNTRL, val); 459 if (ret) 460 goto unlock; 461 462 /* Set up ratiometric scale value, mask off all bits except these */ 463 rsvmask = (ADC_ARB_USRP_RSV_RST | ADC_ARB_USRP_RSV_DTEST0 | 464 ADC_ARB_USRP_RSV_DTEST1 | ADC_ARB_USRP_RSV_OP); 465 if (adc->variant->broken_ratiometric && !force_ratiometric) { 466 /* 467 * Apparently the PM8058 has some kind of bug which is 468 * reflected in the vendor tree drivers/misc/pmix8058-xoadc.c 469 * which just hardcodes the RSV selector to SEL1 (0x20) for 470 * most cases and SEL0 (0x10) for the MUXOFF channel only. 471 * If we force ratiometric (currently only done when attempting 472 * to do ratiometric calibration) this doesn't seem to work 473 * very well and I suspect ratiometric conversion is simply 474 * broken or not supported on the PM8058. 475 * 476 * Maybe IO_SEL2 doesn't exist on PM8058 and bits 4 & 5 select 477 * the mode alone. 478 * 479 * Some PM8058 register documentation would be nice to get 480 * this right. 481 */ 482 if (ch->hwchan->amux_channel == PM8XXX_CHANNEL_MUXOFF) 483 rsvval = ADC_ARB_USRP_RSV_IP_SEL0; 484 else 485 rsvval = ADC_ARB_USRP_RSV_IP_SEL1; 486 } else { 487 if (rsv == 0xff) 488 rsvval = (ch->amux_ip_rsv << ADC_RSV_IP_SEL_SHIFT) | 489 ADC_ARB_USRP_RSV_TRM; 490 else 491 rsvval = (rsv << ADC_RSV_IP_SEL_SHIFT) | 492 ADC_ARB_USRP_RSV_TRM; 493 } 494 495 ret = regmap_update_bits(adc->map, 496 ADC_ARB_USRP_RSV, 497 ~rsvmask, 498 rsvval); 499 if (ret) 500 goto unlock; 501 502 ret = regmap_write(adc->map, ADC_ARB_USRP_ANA_PARAM, 503 ADC_ARB_USRP_ANA_PARAM_DIS); 504 if (ret) 505 goto unlock; 506 507 /* Decimation factor */ 508 ret = regmap_write(adc->map, ADC_ARB_USRP_DIG_PARAM, 509 ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT0 | 510 ADC_ARB_USRP_DIG_PARAM_SEL_SHIFT1 | 511 ch->decimation << ADC_DIG_PARAM_DEC_SHIFT); 512 if (ret) 513 goto unlock; 514 515 ret = regmap_write(adc->map, ADC_ARB_USRP_ANA_PARAM, 516 ADC_ARB_USRP_ANA_PARAM_EN); 517 if (ret) 518 goto unlock; 519 520 /* Enable the arbiter, the Qualcomm code does it twice like this */ 521 ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 522 ADC_ARB_USRP_CNTRL_EN_ARB); 523 if (ret) 524 goto unlock; 525 ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 526 ADC_ARB_USRP_CNTRL_EN_ARB); 527 if (ret) 528 goto unlock; 529 530 531 /* Fire a request! */ 532 reinit_completion(&adc->complete); 533 ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 534 ADC_ARB_USRP_CNTRL_EN_ARB | 535 ADC_ARB_USRP_CNTRL_REQ); 536 if (ret) 537 goto unlock; 538 539 /* Next the interrupt occurs */ 540 ret = wait_for_completion_timeout(&adc->complete, 541 VADC_CONV_TIME_MAX_US); 542 if (!ret) { 543 dev_err(adc->dev, "conversion timed out\n"); 544 ret = -ETIMEDOUT; 545 goto unlock; 546 } 547 548 ret = regmap_read(adc->map, ADC_ARB_USRP_DATA0, &val); 549 if (ret) 550 goto unlock; 551 lsb = val; 552 ret = regmap_read(adc->map, ADC_ARB_USRP_DATA1, &val); 553 if (ret) 554 goto unlock; 555 msb = val; 556 *adc_code = (msb << 8) | lsb; 557 558 /* Turn off the ADC by setting the arbiter to 0 twice */ 559 ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 0); 560 if (ret) 561 goto unlock; 562 ret = regmap_write(adc->map, ADC_ARB_USRP_CNTRL, 0); 563 if (ret) 564 goto unlock; 565 566 unlock: 567 mutex_unlock(&adc->lock); 568 return ret; 569 } 570 571 static int pm8xxx_read_channel(struct pm8xxx_xoadc *adc, 572 const struct pm8xxx_chan_info *ch, 573 u16 *adc_code) 574 { 575 /* 576 * Normally we just use the ratiometric scale value (RSV) predefined 577 * for the channel, but during calibration we need to modify this 578 * so this wrapper is a helper hiding the more complex version. 579 */ 580 return pm8xxx_read_channel_rsv(adc, ch, 0xff, adc_code, false); 581 } 582 583 static int pm8xxx_calibrate_device(struct pm8xxx_xoadc *adc) 584 { 585 const struct pm8xxx_chan_info *ch; 586 u16 read_1250v; 587 u16 read_0625v; 588 u16 read_nomux_rsv5; 589 u16 read_nomux_rsv4; 590 int ret; 591 592 adc->graph[VADC_CALIB_ABSOLUTE].dx = VADC_ABSOLUTE_RANGE_UV; 593 adc->graph[VADC_CALIB_RATIOMETRIC].dx = VADC_RATIOMETRIC_RANGE; 594 595 /* Common reference channel calibration */ 596 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_125V); 597 if (!ch) 598 return -ENODEV; 599 ret = pm8xxx_read_channel(adc, ch, &read_1250v); 600 if (ret) { 601 dev_err(adc->dev, "could not read 1.25V reference channel\n"); 602 return -ENODEV; 603 } 604 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_INTERNAL); 605 if (!ch) 606 return -ENODEV; 607 ret = pm8xxx_read_channel(adc, ch, &read_0625v); 608 if (ret) { 609 dev_err(adc->dev, "could not read 0.625V reference channel\n"); 610 return -ENODEV; 611 } 612 if (read_1250v == read_0625v) { 613 dev_err(adc->dev, "read same ADC code for 1.25V and 0.625V\n"); 614 return -ENODEV; 615 } 616 617 adc->graph[VADC_CALIB_ABSOLUTE].dy = read_1250v - read_0625v; 618 adc->graph[VADC_CALIB_ABSOLUTE].gnd = read_0625v; 619 620 dev_info(adc->dev, "absolute calibration dx = %d uV, dy = %d units\n", 621 VADC_ABSOLUTE_RANGE_UV, adc->graph[VADC_CALIB_ABSOLUTE].dy); 622 623 /* Ratiometric calibration */ 624 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_MUXOFF); 625 if (!ch) 626 return -ENODEV; 627 ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV5, 628 &read_nomux_rsv5, true); 629 if (ret) { 630 dev_err(adc->dev, "could not read MUXOFF reference channel\n"); 631 return -ENODEV; 632 } 633 ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4, 634 &read_nomux_rsv4, true); 635 if (ret) { 636 dev_err(adc->dev, "could not read MUXOFF reference channel\n"); 637 return -ENODEV; 638 } 639 adc->graph[VADC_CALIB_RATIOMETRIC].dy = 640 read_nomux_rsv5 - read_nomux_rsv4; 641 adc->graph[VADC_CALIB_RATIOMETRIC].gnd = read_nomux_rsv4; 642 643 dev_info(adc->dev, "ratiometric calibration dx = %d, dy = %d units\n", 644 VADC_RATIOMETRIC_RANGE, 645 adc->graph[VADC_CALIB_RATIOMETRIC].dy); 646 647 return 0; 648 } 649 650 static int pm8xxx_read_raw(struct iio_dev *indio_dev, 651 struct iio_chan_spec const *chan, 652 int *val, int *val2, long mask) 653 { 654 struct pm8xxx_xoadc *adc = iio_priv(indio_dev); 655 const struct pm8xxx_chan_info *ch; 656 u16 adc_code; 657 int ret; 658 659 switch (mask) { 660 case IIO_CHAN_INFO_PROCESSED: 661 ch = pm8xxx_get_channel(adc, chan->address); 662 if (!ch) { 663 dev_err(adc->dev, "no such channel %lu\n", 664 chan->address); 665 return -EINVAL; 666 } 667 ret = pm8xxx_read_channel(adc, ch, &adc_code); 668 if (ret) 669 return ret; 670 671 ret = qcom_vadc_scale(ch->hwchan->scale_fn_type, 672 &adc->graph[ch->calibration], 673 &ch->hwchan->prescale, 674 (ch->calibration == VADC_CALIB_ABSOLUTE), 675 adc_code, val); 676 if (ret) 677 return ret; 678 679 return IIO_VAL_INT; 680 case IIO_CHAN_INFO_RAW: 681 ch = pm8xxx_get_channel(adc, chan->address); 682 if (!ch) { 683 dev_err(adc->dev, "no such channel %lu\n", 684 chan->address); 685 return -EINVAL; 686 } 687 ret = pm8xxx_read_channel(adc, ch, &adc_code); 688 if (ret) 689 return ret; 690 691 *val = (int)adc_code; 692 return IIO_VAL_INT; 693 default: 694 return -EINVAL; 695 } 696 } 697 698 static int pm8xxx_of_xlate(struct iio_dev *indio_dev, 699 const struct of_phandle_args *iiospec) 700 { 701 struct pm8xxx_xoadc *adc = iio_priv(indio_dev); 702 u8 pre_scale_mux; 703 u8 amux_channel; 704 unsigned int i; 705 706 /* 707 * First cell is prescaler or premux, second cell is analog 708 * mux. 709 */ 710 if (iiospec->args_count != 2) { 711 dev_err(&indio_dev->dev, "wrong number of arguments for %pOFn need 2 got %d\n", 712 iiospec->np, 713 iiospec->args_count); 714 return -EINVAL; 715 } 716 pre_scale_mux = (u8)iiospec->args[0]; 717 amux_channel = (u8)iiospec->args[1]; 718 dev_dbg(&indio_dev->dev, "pre scale/mux: %02x, amux: %02x\n", 719 pre_scale_mux, amux_channel); 720 721 /* We need to match exactly on the prescale/premux and channel */ 722 for (i = 0; i < adc->nchans; i++) 723 if (adc->chans[i].hwchan->pre_scale_mux == pre_scale_mux && 724 adc->chans[i].hwchan->amux_channel == amux_channel) 725 return i; 726 727 return -EINVAL; 728 } 729 730 static const struct iio_info pm8xxx_xoadc_info = { 731 .of_xlate = pm8xxx_of_xlate, 732 .read_raw = pm8xxx_read_raw, 733 }; 734 735 static int pm8xxx_xoadc_parse_channel(struct device *dev, 736 struct device_node *np, 737 const struct xoadc_channel *hw_channels, 738 struct iio_chan_spec *iio_chan, 739 struct pm8xxx_chan_info *ch) 740 { 741 const char *name = np->name; 742 const struct xoadc_channel *hwchan; 743 u32 pre_scale_mux, amux_channel; 744 u32 rsv, dec; 745 int ret; 746 int chid; 747 748 ret = of_property_read_u32_index(np, "reg", 0, &pre_scale_mux); 749 if (ret) { 750 dev_err(dev, "invalid pre scale/mux number %s\n", name); 751 return ret; 752 } 753 ret = of_property_read_u32_index(np, "reg", 1, &amux_channel); 754 if (ret) { 755 dev_err(dev, "invalid amux channel number %s\n", name); 756 return ret; 757 } 758 759 /* Find the right channel setting */ 760 chid = 0; 761 hwchan = &hw_channels[0]; 762 while (hwchan && hwchan->datasheet_name) { 763 if (hwchan->pre_scale_mux == pre_scale_mux && 764 hwchan->amux_channel == amux_channel) 765 break; 766 hwchan++; 767 chid++; 768 } 769 /* The sentinel does not have a name assigned */ 770 if (!hwchan->datasheet_name) { 771 dev_err(dev, "could not locate channel %02x/%02x\n", 772 pre_scale_mux, amux_channel); 773 return -EINVAL; 774 } 775 ch->name = name; 776 ch->hwchan = hwchan; 777 /* Everyone seems to use absolute calibration except in special cases */ 778 ch->calibration = VADC_CALIB_ABSOLUTE; 779 /* Everyone seems to use default ("type 2") decimation */ 780 ch->decimation = VADC_DEF_DECIMATION; 781 782 if (!of_property_read_u32(np, "qcom,ratiometric", &rsv)) { 783 ch->calibration = VADC_CALIB_RATIOMETRIC; 784 if (rsv > XOADC_RSV_MAX) { 785 dev_err(dev, "%s too large RSV value %d\n", name, rsv); 786 return -EINVAL; 787 } 788 if (rsv == AMUX_RSV3) { 789 dev_err(dev, "%s invalid RSV value %d\n", name, rsv); 790 return -EINVAL; 791 } 792 } 793 794 /* Optional decimation, if omitted we use the default */ 795 ret = of_property_read_u32(np, "qcom,decimation", &dec); 796 if (!ret) { 797 ret = qcom_vadc_decimation_from_dt(dec); 798 if (ret < 0) { 799 dev_err(dev, "%s invalid decimation %d\n", 800 name, dec); 801 return ret; 802 } 803 ch->decimation = ret; 804 } 805 806 iio_chan->channel = chid; 807 iio_chan->address = hwchan->amux_channel; 808 iio_chan->datasheet_name = hwchan->datasheet_name; 809 iio_chan->type = hwchan->type; 810 /* All channels are raw or processed */ 811 iio_chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 812 BIT(IIO_CHAN_INFO_PROCESSED); 813 iio_chan->indexed = 1; 814 815 dev_dbg(dev, "channel [PRESCALE/MUX: %02x AMUX: %02x] \"%s\" " 816 "ref voltage: %d, decimation %d " 817 "prescale %d/%d, scale function %d\n", 818 hwchan->pre_scale_mux, hwchan->amux_channel, ch->name, 819 ch->amux_ip_rsv, ch->decimation, hwchan->prescale.num, 820 hwchan->prescale.den, hwchan->scale_fn_type); 821 822 return 0; 823 } 824 825 static int pm8xxx_xoadc_parse_channels(struct pm8xxx_xoadc *adc, 826 struct device_node *np) 827 { 828 struct device_node *child; 829 struct pm8xxx_chan_info *ch; 830 int ret; 831 int i; 832 833 adc->nchans = of_get_available_child_count(np); 834 if (!adc->nchans) { 835 dev_err(adc->dev, "no channel children\n"); 836 return -ENODEV; 837 } 838 dev_dbg(adc->dev, "found %d ADC channels\n", adc->nchans); 839 840 adc->iio_chans = devm_kcalloc(adc->dev, adc->nchans, 841 sizeof(*adc->iio_chans), GFP_KERNEL); 842 if (!adc->iio_chans) 843 return -ENOMEM; 844 845 adc->chans = devm_kcalloc(adc->dev, adc->nchans, 846 sizeof(*adc->chans), GFP_KERNEL); 847 if (!adc->chans) 848 return -ENOMEM; 849 850 i = 0; 851 for_each_available_child_of_node(np, child) { 852 ch = &adc->chans[i]; 853 ret = pm8xxx_xoadc_parse_channel(adc->dev, child, 854 adc->variant->channels, 855 &adc->iio_chans[i], 856 ch); 857 if (ret) { 858 of_node_put(child); 859 return ret; 860 } 861 i++; 862 } 863 864 /* Check for required channels */ 865 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_125V); 866 if (!ch) { 867 dev_err(adc->dev, "missing 1.25V reference channel\n"); 868 return -ENODEV; 869 } 870 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_INTERNAL); 871 if (!ch) { 872 dev_err(adc->dev, "missing 0.625V reference channel\n"); 873 return -ENODEV; 874 } 875 ch = pm8xxx_get_channel(adc, PM8XXX_CHANNEL_MUXOFF); 876 if (!ch) { 877 dev_err(adc->dev, "missing MUXOFF reference channel\n"); 878 return -ENODEV; 879 } 880 881 return 0; 882 } 883 884 static int pm8xxx_xoadc_probe(struct platform_device *pdev) 885 { 886 const struct xoadc_variant *variant; 887 struct pm8xxx_xoadc *adc; 888 struct iio_dev *indio_dev; 889 struct device_node *np = pdev->dev.of_node; 890 struct regmap *map; 891 struct device *dev = &pdev->dev; 892 int ret; 893 894 variant = of_device_get_match_data(dev); 895 if (!variant) 896 return -ENODEV; 897 898 indio_dev = devm_iio_device_alloc(dev, sizeof(*adc)); 899 if (!indio_dev) 900 return -ENOMEM; 901 platform_set_drvdata(pdev, indio_dev); 902 903 adc = iio_priv(indio_dev); 904 adc->dev = dev; 905 adc->variant = variant; 906 init_completion(&adc->complete); 907 mutex_init(&adc->lock); 908 909 ret = pm8xxx_xoadc_parse_channels(adc, np); 910 if (ret) 911 return ret; 912 913 map = dev_get_regmap(dev->parent, NULL); 914 if (!map) { 915 dev_err(dev, "parent regmap unavailable.\n"); 916 return -ENXIO; 917 } 918 adc->map = map; 919 920 /* Bring up regulator */ 921 adc->vref = devm_regulator_get(dev, "xoadc-ref"); 922 if (IS_ERR(adc->vref)) { 923 dev_err(dev, "failed to get XOADC VREF regulator\n"); 924 return PTR_ERR(adc->vref); 925 } 926 ret = regulator_enable(adc->vref); 927 if (ret) { 928 dev_err(dev, "failed to enable XOADC VREF regulator\n"); 929 return ret; 930 } 931 932 ret = devm_request_threaded_irq(dev, platform_get_irq(pdev, 0), 933 pm8xxx_eoc_irq, NULL, 0, variant->name, indio_dev); 934 if (ret) { 935 dev_err(dev, "unable to request IRQ\n"); 936 goto out_disable_vref; 937 } 938 939 indio_dev->dev.parent = dev; 940 indio_dev->dev.of_node = np; 941 indio_dev->name = variant->name; 942 indio_dev->modes = INDIO_DIRECT_MODE; 943 indio_dev->info = &pm8xxx_xoadc_info; 944 indio_dev->channels = adc->iio_chans; 945 indio_dev->num_channels = adc->nchans; 946 947 ret = iio_device_register(indio_dev); 948 if (ret) 949 goto out_disable_vref; 950 951 ret = pm8xxx_calibrate_device(adc); 952 if (ret) 953 goto out_unreg_device; 954 955 dev_info(dev, "%s XOADC driver enabled\n", variant->name); 956 957 return 0; 958 959 out_unreg_device: 960 iio_device_unregister(indio_dev); 961 out_disable_vref: 962 regulator_disable(adc->vref); 963 964 return ret; 965 } 966 967 static int pm8xxx_xoadc_remove(struct platform_device *pdev) 968 { 969 struct iio_dev *indio_dev = platform_get_drvdata(pdev); 970 struct pm8xxx_xoadc *adc = iio_priv(indio_dev); 971 972 iio_device_unregister(indio_dev); 973 974 regulator_disable(adc->vref); 975 976 return 0; 977 } 978 979 static const struct xoadc_variant pm8018_variant = { 980 .name = "PM8018-XOADC", 981 .channels = pm8018_xoadc_channels, 982 }; 983 984 static const struct xoadc_variant pm8038_variant = { 985 .name = "PM8038-XOADC", 986 .channels = pm8038_xoadc_channels, 987 }; 988 989 static const struct xoadc_variant pm8058_variant = { 990 .name = "PM8058-XOADC", 991 .channels = pm8058_xoadc_channels, 992 .broken_ratiometric = true, 993 .prescaling = true, 994 }; 995 996 static const struct xoadc_variant pm8921_variant = { 997 .name = "PM8921-XOADC", 998 .channels = pm8921_xoadc_channels, 999 .second_level_mux = true, 1000 }; 1001 1002 static const struct of_device_id pm8xxx_xoadc_id_table[] = { 1003 { 1004 .compatible = "qcom,pm8018-adc", 1005 .data = &pm8018_variant, 1006 }, 1007 { 1008 .compatible = "qcom,pm8038-adc", 1009 .data = &pm8038_variant, 1010 }, 1011 { 1012 .compatible = "qcom,pm8058-adc", 1013 .data = &pm8058_variant, 1014 }, 1015 { 1016 .compatible = "qcom,pm8921-adc", 1017 .data = &pm8921_variant, 1018 }, 1019 { }, 1020 }; 1021 MODULE_DEVICE_TABLE(of, pm8xxx_xoadc_id_table); 1022 1023 static struct platform_driver pm8xxx_xoadc_driver = { 1024 .driver = { 1025 .name = "pm8xxx-adc", 1026 .of_match_table = pm8xxx_xoadc_id_table, 1027 }, 1028 .probe = pm8xxx_xoadc_probe, 1029 .remove = pm8xxx_xoadc_remove, 1030 }; 1031 module_platform_driver(pm8xxx_xoadc_driver); 1032 1033 MODULE_DESCRIPTION("PM8xxx XOADC driver"); 1034 MODULE_LICENSE("GPL v2"); 1035 MODULE_ALIAS("platform:pm8xxx-xoadc"); 1036