1 /* 2 * iio/adc/max9611.c 3 * 4 * Maxim max9611/max9612 high side current sense amplifier with 5 * 12-bit ADC interface. 6 * 7 * Copyright (C) 2017 Jacopo Mondi 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License version 2 as 11 * published by the Free Software Foundation. 12 */ 13 14 /* 15 * This driver supports input common-mode voltage, current-sense 16 * amplifier with programmable gains and die temperature reading from 17 * Maxim max9611/max9612. 18 * 19 * Op-amp, analog comparator, and watchdog functionalities are not 20 * supported by this driver. 21 */ 22 23 #include <linux/delay.h> 24 #include <linux/i2c.h> 25 #include <linux/iio/iio.h> 26 #include <linux/iio/sysfs.h> 27 #include <linux/module.h> 28 #include <linux/of_device.h> 29 30 #define DRIVER_NAME "max9611" 31 32 /* max9611 register addresses */ 33 #define MAX9611_REG_CSA_DATA 0x00 34 #define MAX9611_REG_RS_DATA 0x02 35 #define MAX9611_REG_TEMP_DATA 0x08 36 #define MAX9611_REG_CTRL1 0x0a 37 #define MAX9611_REG_CTRL2 0x0b 38 39 /* max9611 REG1 mux configuration options */ 40 #define MAX9611_MUX_MASK GENMASK(3, 0) 41 #define MAX9611_MUX_SENSE_1x 0x00 42 #define MAX9611_MUX_SENSE_4x 0x01 43 #define MAX9611_MUX_SENSE_8x 0x02 44 #define MAX9611_INPUT_VOLT 0x03 45 #define MAX9611_MUX_TEMP 0x06 46 47 /* max9611 voltage (both csa and input) helper macros */ 48 #define MAX9611_VOLTAGE_SHIFT 0x04 49 #define MAX9611_VOLTAGE_RAW(_r) ((_r) >> MAX9611_VOLTAGE_SHIFT) 50 51 /* 52 * max9611 current sense amplifier voltage output: 53 * LSB and offset values depends on selected gain (1x, 4x, 8x) 54 * 55 * GAIN LSB (nV) OFFSET (LSB steps) 56 * 1x 107500 1 57 * 4x 26880 1 58 * 8x 13440 3 59 * 60 * The complete formula to calculate current sense voltage is: 61 * (((adc_read >> 4) - offset) / ((1 / LSB) * 10^-3) 62 */ 63 #define MAX9611_CSA_1X_LSB_nV 107500 64 #define MAX9611_CSA_4X_LSB_nV 26880 65 #define MAX9611_CSA_8X_LSB_nV 13440 66 67 #define MAX9611_CSA_1X_OFFS_RAW 1 68 #define MAX9611_CSA_4X_OFFS_RAW 1 69 #define MAX9611_CSA_8X_OFFS_RAW 3 70 71 /* 72 * max9611 common input mode (CIM): LSB is 14mV, with 14mV offset at 25 C 73 * 74 * The complete formula to calculate input common voltage is: 75 * (((adc_read >> 4) * 1000) - offset) / (1 / 14 * 1000) 76 */ 77 #define MAX9611_CIM_LSB_mV 14 78 #define MAX9611_CIM_OFFSET_RAW 1 79 80 /* 81 * max9611 temperature reading: LSB is 480 milli degrees Celsius 82 * 83 * The complete formula to calculate temperature is: 84 * ((adc_read >> 7) * 1000) / (1 / 480 * 1000) 85 */ 86 #define MAX9611_TEMP_MAX_POS 0x7f80 87 #define MAX9611_TEMP_MAX_NEG 0xff80 88 #define MAX9611_TEMP_MIN_NEG 0xd980 89 #define MAX9611_TEMP_MASK GENMASK(7, 15) 90 #define MAX9611_TEMP_SHIFT 0x07 91 #define MAX9611_TEMP_RAW(_r) ((_r) >> MAX9611_TEMP_SHIFT) 92 #define MAX9611_TEMP_SCALE_NUM 1000000 93 #define MAX9611_TEMP_SCALE_DIV 2083 94 95 struct max9611_dev { 96 struct device *dev; 97 struct i2c_client *i2c_client; 98 struct mutex lock; 99 unsigned int shunt_resistor_uohm; 100 }; 101 102 enum max9611_conf_ids { 103 CONF_SENSE_1x, 104 CONF_SENSE_4x, 105 CONF_SENSE_8x, 106 CONF_IN_VOLT, 107 CONF_TEMP, 108 }; 109 110 /** 111 * max9611_mux_conf - associate ADC mux configuration with register address 112 * where data shall be read from 113 */ 114 static const unsigned int max9611_mux_conf[][2] = { 115 /* CONF_SENSE_1x */ 116 { MAX9611_MUX_SENSE_1x, MAX9611_REG_CSA_DATA }, 117 /* CONF_SENSE_4x */ 118 { MAX9611_MUX_SENSE_4x, MAX9611_REG_CSA_DATA }, 119 /* CONF_SENSE_8x */ 120 { MAX9611_MUX_SENSE_8x, MAX9611_REG_CSA_DATA }, 121 /* CONF_IN_VOLT */ 122 { MAX9611_INPUT_VOLT, MAX9611_REG_RS_DATA }, 123 /* CONF_TEMP */ 124 { MAX9611_MUX_TEMP, MAX9611_REG_TEMP_DATA }, 125 }; 126 127 enum max9611_csa_gain { 128 CSA_GAIN_1x, 129 CSA_GAIN_4x, 130 CSA_GAIN_8x, 131 }; 132 133 enum max9611_csa_gain_params { 134 CSA_GAIN_LSB_nV, 135 CSA_GAIN_OFFS_RAW, 136 }; 137 138 /** 139 * max9611_csa_gain_conf - associate gain multiplier with LSB and 140 * offset values. 141 * 142 * Group together parameters associated with configurable gain 143 * on current sense amplifier path to ADC interface. 144 * Current sense read routine adjusts gain until it gets a meaningful 145 * value; use this structure to retrieve the correct LSB and offset values. 146 */ 147 static const unsigned int max9611_gain_conf[][2] = { 148 { /* [0] CSA_GAIN_1x */ 149 MAX9611_CSA_1X_LSB_nV, 150 MAX9611_CSA_1X_OFFS_RAW, 151 }, 152 { /* [1] CSA_GAIN_4x */ 153 MAX9611_CSA_4X_LSB_nV, 154 MAX9611_CSA_4X_OFFS_RAW, 155 }, 156 { /* [2] CSA_GAIN_8x */ 157 MAX9611_CSA_8X_LSB_nV, 158 MAX9611_CSA_8X_OFFS_RAW, 159 }, 160 }; 161 162 enum max9611_chan_addrs { 163 MAX9611_CHAN_VOLTAGE_INPUT, 164 MAX9611_CHAN_VOLTAGE_SENSE, 165 MAX9611_CHAN_TEMPERATURE, 166 MAX9611_CHAN_CURRENT_LOAD, 167 MAX9611_CHAN_POWER_LOAD, 168 }; 169 170 static const struct iio_chan_spec max9611_channels[] = { 171 { 172 .type = IIO_TEMP, 173 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 174 BIT(IIO_CHAN_INFO_SCALE), 175 .address = MAX9611_CHAN_TEMPERATURE, 176 }, 177 { 178 .type = IIO_VOLTAGE, 179 .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), 180 .address = MAX9611_CHAN_VOLTAGE_SENSE, 181 .indexed = 1, 182 .channel = 0, 183 }, 184 { 185 .type = IIO_VOLTAGE, 186 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 187 BIT(IIO_CHAN_INFO_SCALE) | 188 BIT(IIO_CHAN_INFO_OFFSET), 189 .address = MAX9611_CHAN_VOLTAGE_INPUT, 190 .indexed = 1, 191 .channel = 1, 192 }, 193 { 194 .type = IIO_CURRENT, 195 .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), 196 .address = MAX9611_CHAN_CURRENT_LOAD, 197 }, 198 { 199 .type = IIO_POWER, 200 .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), 201 .address = MAX9611_CHAN_POWER_LOAD 202 }, 203 }; 204 205 /** 206 * max9611_read_single() - read a single value from ADC interface 207 * 208 * Data registers are 16 bit long, spread between two 8 bit registers 209 * with consecutive addresses. 210 * Configure ADC mux first, then read register at address "reg_addr". 211 * The smbus_read_word routine asks for 16 bits and the ADC is kind enough 212 * to return values from "reg_addr" and "reg_addr + 1" consecutively. 213 * Data are transmitted with big-endian ordering: MSB arrives first. 214 * 215 * @max9611: max9611 device 216 * @selector: index for mux and register configuration 217 * @raw_val: the value returned from ADC 218 */ 219 static int max9611_read_single(struct max9611_dev *max9611, 220 enum max9611_conf_ids selector, 221 u16 *raw_val) 222 { 223 int ret; 224 225 u8 mux_conf = max9611_mux_conf[selector][0] & MAX9611_MUX_MASK; 226 u8 reg_addr = max9611_mux_conf[selector][1]; 227 228 /* 229 * Keep mutex lock held during read-write to avoid mux register 230 * (CTRL1) re-configuration. 231 */ 232 mutex_lock(&max9611->lock); 233 ret = i2c_smbus_write_byte_data(max9611->i2c_client, 234 MAX9611_REG_CTRL1, mux_conf); 235 if (ret) { 236 dev_err(max9611->dev, "i2c write byte failed: 0x%2x - 0x%2x\n", 237 MAX9611_REG_CTRL1, mux_conf); 238 mutex_unlock(&max9611->lock); 239 return ret; 240 } 241 242 /* 243 * need a delay here to make register configuration 244 * stabilize. 1 msec at least, from empirical testing. 245 */ 246 usleep_range(1000, 2000); 247 248 ret = i2c_smbus_read_word_swapped(max9611->i2c_client, reg_addr); 249 if (ret < 0) { 250 dev_err(max9611->dev, "i2c read word from 0x%2x failed\n", 251 reg_addr); 252 mutex_unlock(&max9611->lock); 253 return ret; 254 } 255 256 *raw_val = ret; 257 mutex_unlock(&max9611->lock); 258 259 return 0; 260 } 261 262 /** 263 * max9611_read_csa_voltage() - read current sense amplifier output voltage 264 * 265 * Current sense amplifier output voltage is read through a configurable 266 * 1x, 4x or 8x gain. 267 * Start with plain 1x gain, and adjust gain control properly until a 268 * meaningful value is read from ADC output. 269 * 270 * @max9611: max9611 device 271 * @adc_raw: raw value read from ADC output 272 * @csa_gain: gain configuration option selector 273 */ 274 static int max9611_read_csa_voltage(struct max9611_dev *max9611, 275 u16 *adc_raw, 276 enum max9611_csa_gain *csa_gain) 277 { 278 enum max9611_conf_ids gain_selectors[] = { 279 CONF_SENSE_1x, 280 CONF_SENSE_4x, 281 CONF_SENSE_8x 282 }; 283 unsigned int i; 284 int ret; 285 286 for (i = 0; i < ARRAY_SIZE(gain_selectors); ++i) { 287 ret = max9611_read_single(max9611, gain_selectors[i], adc_raw); 288 if (ret) 289 return ret; 290 291 if (*adc_raw > 0) { 292 *csa_gain = gain_selectors[i]; 293 return 0; 294 } 295 } 296 297 return -EIO; 298 } 299 300 static int max9611_read_raw(struct iio_dev *indio_dev, 301 struct iio_chan_spec const *chan, 302 int *val, int *val2, long mask) 303 { 304 struct max9611_dev *dev = iio_priv(indio_dev); 305 enum max9611_csa_gain gain_selector; 306 const unsigned int *csa_gain; 307 u16 adc_data; 308 int ret; 309 310 switch (mask) { 311 case IIO_CHAN_INFO_RAW: 312 313 switch (chan->address) { 314 case MAX9611_CHAN_TEMPERATURE: 315 ret = max9611_read_single(dev, CONF_TEMP, 316 &adc_data); 317 if (ret) 318 return -EINVAL; 319 320 *val = MAX9611_TEMP_RAW(adc_data); 321 return IIO_VAL_INT; 322 323 case MAX9611_CHAN_VOLTAGE_INPUT: 324 ret = max9611_read_single(dev, CONF_IN_VOLT, 325 &adc_data); 326 if (ret) 327 return -EINVAL; 328 329 *val = MAX9611_VOLTAGE_RAW(adc_data); 330 return IIO_VAL_INT; 331 } 332 333 break; 334 335 case IIO_CHAN_INFO_OFFSET: 336 /* MAX9611_CHAN_VOLTAGE_INPUT */ 337 *val = MAX9611_CIM_OFFSET_RAW; 338 339 return IIO_VAL_INT; 340 341 case IIO_CHAN_INFO_SCALE: 342 343 switch (chan->address) { 344 case MAX9611_CHAN_TEMPERATURE: 345 *val = MAX9611_TEMP_SCALE_NUM; 346 *val2 = MAX9611_TEMP_SCALE_DIV; 347 348 return IIO_VAL_FRACTIONAL; 349 350 case MAX9611_CHAN_VOLTAGE_INPUT: 351 *val = MAX9611_CIM_LSB_mV; 352 353 return IIO_VAL_INT; 354 } 355 356 break; 357 358 case IIO_CHAN_INFO_PROCESSED: 359 360 switch (chan->address) { 361 case MAX9611_CHAN_VOLTAGE_SENSE: 362 /* 363 * processed (mV): (raw - offset) * LSB (nV) / 10^6 364 * 365 * Even if max9611 can output raw csa voltage readings, 366 * use a produced value as scale depends on gain. 367 */ 368 ret = max9611_read_csa_voltage(dev, &adc_data, 369 &gain_selector); 370 if (ret) 371 return -EINVAL; 372 373 csa_gain = max9611_gain_conf[gain_selector]; 374 375 adc_data -= csa_gain[CSA_GAIN_OFFS_RAW]; 376 *val = MAX9611_VOLTAGE_RAW(adc_data) * 377 csa_gain[CSA_GAIN_LSB_nV]; 378 *val2 = 1000000; 379 380 return IIO_VAL_FRACTIONAL; 381 382 case MAX9611_CHAN_CURRENT_LOAD: 383 /* processed (mA): Vcsa (nV) / Rshunt (uOhm) */ 384 ret = max9611_read_csa_voltage(dev, &adc_data, 385 &gain_selector); 386 if (ret) 387 return -EINVAL; 388 389 csa_gain = max9611_gain_conf[gain_selector]; 390 391 adc_data -= csa_gain[CSA_GAIN_OFFS_RAW]; 392 *val = MAX9611_VOLTAGE_RAW(adc_data) * 393 csa_gain[CSA_GAIN_LSB_nV]; 394 *val2 = dev->shunt_resistor_uohm; 395 396 return IIO_VAL_FRACTIONAL; 397 398 case MAX9611_CHAN_POWER_LOAD: 399 /* 400 * processed (mW): Vin (mV) * Vcsa (uV) / 401 * Rshunt (uOhm) 402 */ 403 ret = max9611_read_single(dev, CONF_IN_VOLT, 404 &adc_data); 405 if (ret) 406 return -EINVAL; 407 408 adc_data -= MAX9611_CIM_OFFSET_RAW; 409 *val = MAX9611_VOLTAGE_RAW(adc_data) * 410 MAX9611_CIM_LSB_mV; 411 412 ret = max9611_read_csa_voltage(dev, &adc_data, 413 &gain_selector); 414 if (ret) 415 return -EINVAL; 416 417 csa_gain = max9611_gain_conf[gain_selector]; 418 419 /* divide by 10^3 here to avoid 32bit overflow */ 420 adc_data -= csa_gain[CSA_GAIN_OFFS_RAW]; 421 *val *= MAX9611_VOLTAGE_RAW(adc_data) * 422 csa_gain[CSA_GAIN_LSB_nV] / 1000; 423 *val2 = dev->shunt_resistor_uohm; 424 425 return IIO_VAL_FRACTIONAL; 426 } 427 428 break; 429 } 430 431 return -EINVAL; 432 } 433 434 static ssize_t max9611_shunt_resistor_show(struct device *dev, 435 struct device_attribute *attr, 436 char *buf) 437 { 438 struct max9611_dev *max9611 = iio_priv(dev_to_iio_dev(dev)); 439 unsigned int i, r; 440 441 i = max9611->shunt_resistor_uohm / 1000000; 442 r = max9611->shunt_resistor_uohm % 1000000; 443 444 return sprintf(buf, "%u.%06u\n", i, r); 445 } 446 447 static IIO_DEVICE_ATTR(in_power_shunt_resistor, 0444, 448 max9611_shunt_resistor_show, NULL, 0); 449 static IIO_DEVICE_ATTR(in_current_shunt_resistor, 0444, 450 max9611_shunt_resistor_show, NULL, 0); 451 452 static struct attribute *max9611_attributes[] = { 453 &iio_dev_attr_in_power_shunt_resistor.dev_attr.attr, 454 &iio_dev_attr_in_current_shunt_resistor.dev_attr.attr, 455 NULL, 456 }; 457 458 static const struct attribute_group max9611_attribute_group = { 459 .attrs = max9611_attributes, 460 }; 461 462 static const struct iio_info indio_info = { 463 .driver_module = THIS_MODULE, 464 .read_raw = max9611_read_raw, 465 .attrs = &max9611_attribute_group, 466 }; 467 468 static int max9611_init(struct max9611_dev *max9611) 469 { 470 struct i2c_client *client = max9611->i2c_client; 471 u16 regval; 472 int ret; 473 474 if (!i2c_check_functionality(client->adapter, 475 I2C_FUNC_SMBUS_WRITE_BYTE | 476 I2C_FUNC_SMBUS_READ_WORD_DATA)) { 477 dev_err(max9611->dev, 478 "I2c adapter does not support smbus write_byte or read_word functionalities: aborting probe.\n"); 479 return -EINVAL; 480 } 481 482 /* Make sure die temperature is in range to test communications. */ 483 ret = max9611_read_single(max9611, CONF_TEMP, ®val); 484 if (ret) 485 return ret; 486 487 regval = ret & MAX9611_TEMP_MASK; 488 489 if ((regval > MAX9611_TEMP_MAX_POS && 490 regval < MAX9611_TEMP_MIN_NEG) || 491 regval > MAX9611_TEMP_MAX_NEG) { 492 dev_err(max9611->dev, 493 "Invalid value received from ADC 0x%4x: aborting\n", 494 regval); 495 return -EIO; 496 } 497 498 /* Mux shall be zeroed back before applying other configurations */ 499 ret = i2c_smbus_write_byte_data(max9611->i2c_client, 500 MAX9611_REG_CTRL1, 0); 501 if (ret) { 502 dev_err(max9611->dev, "i2c write byte failed: 0x%2x - 0x%2x\n", 503 MAX9611_REG_CTRL1, 0); 504 return ret; 505 } 506 507 ret = i2c_smbus_write_byte_data(max9611->i2c_client, 508 MAX9611_REG_CTRL2, 0); 509 if (ret) { 510 dev_err(max9611->dev, "i2c write byte failed: 0x%2x - 0x%2x\n", 511 MAX9611_REG_CTRL2, 0); 512 return ret; 513 } 514 usleep_range(1000, 2000); 515 516 return 0; 517 } 518 519 static const struct of_device_id max9611_of_table[] = { 520 {.compatible = "maxim,max9611", .data = "max9611"}, 521 {.compatible = "maxim,max9612", .data = "max9612"}, 522 { }, 523 }; 524 525 MODULE_DEVICE_TABLE(of, max9611_of_table); 526 static int max9611_probe(struct i2c_client *client, 527 const struct i2c_device_id *id) 528 { 529 const char * const shunt_res_prop = "shunt-resistor-micro-ohms"; 530 const struct device_node *of_node = client->dev.of_node; 531 const struct of_device_id *of_id = 532 of_match_device(max9611_of_table, &client->dev); 533 struct max9611_dev *max9611; 534 struct iio_dev *indio_dev; 535 unsigned int of_shunt; 536 int ret; 537 538 indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*max9611)); 539 if (!indio_dev) 540 return -ENOMEM; 541 542 i2c_set_clientdata(client, indio_dev); 543 544 max9611 = iio_priv(indio_dev); 545 max9611->dev = &client->dev; 546 max9611->i2c_client = client; 547 mutex_init(&max9611->lock); 548 549 ret = of_property_read_u32(of_node, shunt_res_prop, &of_shunt); 550 if (ret) { 551 dev_err(&client->dev, 552 "Missing %s property for %pOF node\n", 553 shunt_res_prop, of_node); 554 return ret; 555 } 556 max9611->shunt_resistor_uohm = of_shunt; 557 558 ret = max9611_init(max9611); 559 if (ret) 560 return ret; 561 562 indio_dev->dev.parent = &client->dev; 563 indio_dev->dev.of_node = client->dev.of_node; 564 indio_dev->name = of_id->data; 565 indio_dev->modes = INDIO_DIRECT_MODE; 566 indio_dev->info = &indio_info; 567 indio_dev->channels = max9611_channels; 568 indio_dev->num_channels = ARRAY_SIZE(max9611_channels); 569 570 return devm_iio_device_register(&client->dev, indio_dev); 571 } 572 573 static struct i2c_driver max9611_driver = { 574 .driver = { 575 .name = DRIVER_NAME, 576 .owner = THIS_MODULE, 577 .of_match_table = max9611_of_table, 578 }, 579 .probe = max9611_probe, 580 }; 581 module_i2c_driver(max9611_driver); 582 583 MODULE_AUTHOR("Jacopo Mondi <jacopo+renesas@jmondi.org>"); 584 MODULE_DESCRIPTION("Maxim max9611/12 current sense amplifier with 12bit ADC"); 585 MODULE_LICENSE("GPL v2"); 586