1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * iio/adc/max1027.c 4 * Copyright (C) 2014 Philippe Reynes 5 * 6 * based on linux/drivers/iio/ad7923.c 7 * Copyright 2011 Analog Devices Inc (from AD7923 Driver) 8 * Copyright 2012 CS Systemes d'Information 9 * 10 * max1027.c 11 * 12 * Partial support for max1027 and similar chips. 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/mod_devicetable.h> 18 #include <linux/spi/spi.h> 19 #include <linux/delay.h> 20 21 #include <linux/iio/iio.h> 22 #include <linux/iio/buffer.h> 23 #include <linux/iio/trigger.h> 24 #include <linux/iio/trigger_consumer.h> 25 #include <linux/iio/triggered_buffer.h> 26 27 #define MAX1027_CONV_REG BIT(7) 28 #define MAX1027_SETUP_REG BIT(6) 29 #define MAX1027_AVG_REG BIT(5) 30 #define MAX1027_RST_REG BIT(4) 31 32 /* conversion register */ 33 #define MAX1027_TEMP BIT(0) 34 #define MAX1027_SCAN_0_N (0x00 << 1) 35 #define MAX1027_SCAN_N_M (0x01 << 1) 36 #define MAX1027_SCAN_N (0x02 << 1) 37 #define MAX1027_NOSCAN (0x03 << 1) 38 #define MAX1027_CHAN(n) ((n) << 3) 39 40 /* setup register */ 41 #define MAX1027_UNIPOLAR 0x02 42 #define MAX1027_BIPOLAR 0x03 43 #define MAX1027_REF_MODE0 (0x00 << 2) 44 #define MAX1027_REF_MODE1 (0x01 << 2) 45 #define MAX1027_REF_MODE2 (0x02 << 2) 46 #define MAX1027_REF_MODE3 (0x03 << 2) 47 #define MAX1027_CKS_MODE0 (0x00 << 4) 48 #define MAX1027_CKS_MODE1 (0x01 << 4) 49 #define MAX1027_CKS_MODE2 (0x02 << 4) 50 #define MAX1027_CKS_MODE3 (0x03 << 4) 51 52 /* averaging register */ 53 #define MAX1027_NSCAN_4 0x00 54 #define MAX1027_NSCAN_8 0x01 55 #define MAX1027_NSCAN_12 0x02 56 #define MAX1027_NSCAN_16 0x03 57 #define MAX1027_NAVG_4 (0x00 << 2) 58 #define MAX1027_NAVG_8 (0x01 << 2) 59 #define MAX1027_NAVG_16 (0x02 << 2) 60 #define MAX1027_NAVG_32 (0x03 << 2) 61 #define MAX1027_AVG_EN BIT(4) 62 63 /* Device can achieve 300ksps so we assume a 3.33us conversion delay */ 64 #define MAX1027_CONVERSION_UDELAY 4 65 66 enum max1027_id { 67 max1027, 68 max1029, 69 max1031, 70 max1227, 71 max1229, 72 max1231, 73 }; 74 75 static const struct spi_device_id max1027_id[] = { 76 {"max1027", max1027}, 77 {"max1029", max1029}, 78 {"max1031", max1031}, 79 {"max1227", max1227}, 80 {"max1229", max1229}, 81 {"max1231", max1231}, 82 {} 83 }; 84 MODULE_DEVICE_TABLE(spi, max1027_id); 85 86 static const struct of_device_id max1027_adc_dt_ids[] = { 87 { .compatible = "maxim,max1027" }, 88 { .compatible = "maxim,max1029" }, 89 { .compatible = "maxim,max1031" }, 90 { .compatible = "maxim,max1227" }, 91 { .compatible = "maxim,max1229" }, 92 { .compatible = "maxim,max1231" }, 93 {}, 94 }; 95 MODULE_DEVICE_TABLE(of, max1027_adc_dt_ids); 96 97 #define MAX1027_V_CHAN(index, depth) \ 98 { \ 99 .type = IIO_VOLTAGE, \ 100 .indexed = 1, \ 101 .channel = index, \ 102 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 103 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 104 .scan_index = index + 1, \ 105 .scan_type = { \ 106 .sign = 'u', \ 107 .realbits = depth, \ 108 .storagebits = 16, \ 109 .shift = (depth == 10) ? 2 : 0, \ 110 .endianness = IIO_BE, \ 111 }, \ 112 } 113 114 #define MAX1027_T_CHAN \ 115 { \ 116 .type = IIO_TEMP, \ 117 .channel = 0, \ 118 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 119 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 120 .scan_index = 0, \ 121 .scan_type = { \ 122 .sign = 'u', \ 123 .realbits = 12, \ 124 .storagebits = 16, \ 125 .endianness = IIO_BE, \ 126 }, \ 127 } 128 129 #define MAX1X27_CHANNELS(depth) \ 130 MAX1027_T_CHAN, \ 131 MAX1027_V_CHAN(0, depth), \ 132 MAX1027_V_CHAN(1, depth), \ 133 MAX1027_V_CHAN(2, depth), \ 134 MAX1027_V_CHAN(3, depth), \ 135 MAX1027_V_CHAN(4, depth), \ 136 MAX1027_V_CHAN(5, depth), \ 137 MAX1027_V_CHAN(6, depth), \ 138 MAX1027_V_CHAN(7, depth) 139 140 #define MAX1X29_CHANNELS(depth) \ 141 MAX1X27_CHANNELS(depth), \ 142 MAX1027_V_CHAN(8, depth), \ 143 MAX1027_V_CHAN(9, depth), \ 144 MAX1027_V_CHAN(10, depth), \ 145 MAX1027_V_CHAN(11, depth) 146 147 #define MAX1X31_CHANNELS(depth) \ 148 MAX1X29_CHANNELS(depth), \ 149 MAX1027_V_CHAN(12, depth), \ 150 MAX1027_V_CHAN(13, depth), \ 151 MAX1027_V_CHAN(14, depth), \ 152 MAX1027_V_CHAN(15, depth) 153 154 static const struct iio_chan_spec max1027_channels[] = { 155 MAX1X27_CHANNELS(10), 156 }; 157 158 static const struct iio_chan_spec max1029_channels[] = { 159 MAX1X29_CHANNELS(10), 160 }; 161 162 static const struct iio_chan_spec max1031_channels[] = { 163 MAX1X31_CHANNELS(10), 164 }; 165 166 static const struct iio_chan_spec max1227_channels[] = { 167 MAX1X27_CHANNELS(12), 168 }; 169 170 static const struct iio_chan_spec max1229_channels[] = { 171 MAX1X29_CHANNELS(12), 172 }; 173 174 static const struct iio_chan_spec max1231_channels[] = { 175 MAX1X31_CHANNELS(12), 176 }; 177 178 /* 179 * These devices are able to scan from 0 to N, N being the highest voltage 180 * channel requested by the user. The temperature can be included or not, 181 * but cannot be retrieved alone. Based on the below 182 * ->available_scan_masks, the core will select the most appropriate 183 * ->active_scan_mask and the "minimum" number of channels will be 184 * scanned and pushed to the buffers. 185 * 186 * For example, if the user wants channels 1, 4 and 5, all channels from 187 * 0 to 5 will be scanned and pushed to the IIO buffers. The core will then 188 * filter out the unneeded samples based on the ->active_scan_mask that has 189 * been selected and only channels 1, 4 and 5 will be available to the user 190 * in the shared buffer. 191 */ 192 #define MAX1X27_SCAN_MASK_TEMP BIT(0) 193 194 #define MAX1X27_SCAN_MASKS(temp) \ 195 GENMASK(1, 1 - (temp)), GENMASK(2, 1 - (temp)), \ 196 GENMASK(3, 1 - (temp)), GENMASK(4, 1 - (temp)), \ 197 GENMASK(5, 1 - (temp)), GENMASK(6, 1 - (temp)), \ 198 GENMASK(7, 1 - (temp)), GENMASK(8, 1 - (temp)) 199 200 #define MAX1X29_SCAN_MASKS(temp) \ 201 MAX1X27_SCAN_MASKS(temp), \ 202 GENMASK(9, 1 - (temp)), GENMASK(10, 1 - (temp)), \ 203 GENMASK(11, 1 - (temp)), GENMASK(12, 1 - (temp)) 204 205 #define MAX1X31_SCAN_MASKS(temp) \ 206 MAX1X29_SCAN_MASKS(temp), \ 207 GENMASK(13, 1 - (temp)), GENMASK(14, 1 - (temp)), \ 208 GENMASK(15, 1 - (temp)), GENMASK(16, 1 - (temp)) 209 210 static const unsigned long max1027_available_scan_masks[] = { 211 MAX1X27_SCAN_MASKS(0), 212 MAX1X27_SCAN_MASKS(1), 213 0x00000000, 214 }; 215 216 static const unsigned long max1029_available_scan_masks[] = { 217 MAX1X29_SCAN_MASKS(0), 218 MAX1X29_SCAN_MASKS(1), 219 0x00000000, 220 }; 221 222 static const unsigned long max1031_available_scan_masks[] = { 223 MAX1X31_SCAN_MASKS(0), 224 MAX1X31_SCAN_MASKS(1), 225 0x00000000, 226 }; 227 228 struct max1027_chip_info { 229 const struct iio_chan_spec *channels; 230 unsigned int num_channels; 231 const unsigned long *available_scan_masks; 232 }; 233 234 static const struct max1027_chip_info max1027_chip_info_tbl[] = { 235 [max1027] = { 236 .channels = max1027_channels, 237 .num_channels = ARRAY_SIZE(max1027_channels), 238 .available_scan_masks = max1027_available_scan_masks, 239 }, 240 [max1029] = { 241 .channels = max1029_channels, 242 .num_channels = ARRAY_SIZE(max1029_channels), 243 .available_scan_masks = max1029_available_scan_masks, 244 }, 245 [max1031] = { 246 .channels = max1031_channels, 247 .num_channels = ARRAY_SIZE(max1031_channels), 248 .available_scan_masks = max1031_available_scan_masks, 249 }, 250 [max1227] = { 251 .channels = max1227_channels, 252 .num_channels = ARRAY_SIZE(max1227_channels), 253 .available_scan_masks = max1027_available_scan_masks, 254 }, 255 [max1229] = { 256 .channels = max1229_channels, 257 .num_channels = ARRAY_SIZE(max1229_channels), 258 .available_scan_masks = max1029_available_scan_masks, 259 }, 260 [max1231] = { 261 .channels = max1231_channels, 262 .num_channels = ARRAY_SIZE(max1231_channels), 263 .available_scan_masks = max1031_available_scan_masks, 264 }, 265 }; 266 267 struct max1027_state { 268 const struct max1027_chip_info *info; 269 struct spi_device *spi; 270 struct iio_trigger *trig; 271 __be16 *buffer; 272 struct mutex lock; 273 struct completion complete; 274 275 u8 reg ____cacheline_aligned; 276 }; 277 278 static int max1027_wait_eoc(struct iio_dev *indio_dev) 279 { 280 struct max1027_state *st = iio_priv(indio_dev); 281 unsigned int conversion_time = MAX1027_CONVERSION_UDELAY; 282 int ret; 283 284 if (st->spi->irq) { 285 ret = wait_for_completion_timeout(&st->complete, 286 msecs_to_jiffies(1000)); 287 reinit_completion(&st->complete); 288 if (!ret) 289 return -ETIMEDOUT; 290 } else { 291 if (indio_dev->active_scan_mask) 292 conversion_time *= hweight32(*indio_dev->active_scan_mask); 293 294 usleep_range(conversion_time, conversion_time * 2); 295 } 296 297 return 0; 298 } 299 300 /* Scan from chan 0 to the highest requested channel. Include temperature on demand. */ 301 static int max1027_configure_chans_and_start(struct iio_dev *indio_dev) 302 { 303 struct max1027_state *st = iio_priv(indio_dev); 304 305 st->reg = MAX1027_CONV_REG | MAX1027_SCAN_0_N; 306 st->reg |= MAX1027_CHAN(fls(*indio_dev->active_scan_mask) - 2); 307 if (*indio_dev->active_scan_mask & MAX1X27_SCAN_MASK_TEMP) 308 st->reg |= MAX1027_TEMP; 309 310 return spi_write(st->spi, &st->reg, 1); 311 } 312 313 static int max1027_enable_trigger(struct iio_dev *indio_dev, bool enable) 314 { 315 struct max1027_state *st = iio_priv(indio_dev); 316 317 st->reg = MAX1027_SETUP_REG | MAX1027_REF_MODE2; 318 319 /* 320 * Start acquisition on: 321 * MODE0: external hardware trigger wired to the cnvst input pin 322 * MODE2: conversion register write 323 */ 324 if (enable) 325 st->reg |= MAX1027_CKS_MODE0; 326 else 327 st->reg |= MAX1027_CKS_MODE2; 328 329 return spi_write(st->spi, &st->reg, 1); 330 } 331 332 static int max1027_read_single_value(struct iio_dev *indio_dev, 333 struct iio_chan_spec const *chan, 334 int *val) 335 { 336 int ret; 337 struct max1027_state *st = iio_priv(indio_dev); 338 339 ret = iio_device_claim_direct_mode(indio_dev); 340 if (ret) 341 return ret; 342 343 /* Configure conversion register with the requested chan */ 344 st->reg = MAX1027_CONV_REG | MAX1027_CHAN(chan->channel) | 345 MAX1027_NOSCAN; 346 if (chan->type == IIO_TEMP) 347 st->reg |= MAX1027_TEMP; 348 ret = spi_write(st->spi, &st->reg, 1); 349 if (ret < 0) { 350 dev_err(&indio_dev->dev, 351 "Failed to configure conversion register\n"); 352 iio_device_release_direct_mode(indio_dev); 353 return ret; 354 } 355 356 /* 357 * For an unknown reason, when we use the mode "10" (write 358 * conversion register), the interrupt doesn't occur every time. 359 * So we just wait the maximum conversion time and deliver the value. 360 */ 361 ret = max1027_wait_eoc(indio_dev); 362 if (ret) 363 return ret; 364 365 /* Read result */ 366 ret = spi_read(st->spi, st->buffer, (chan->type == IIO_TEMP) ? 4 : 2); 367 368 iio_device_release_direct_mode(indio_dev); 369 370 if (ret < 0) 371 return ret; 372 373 *val = be16_to_cpu(st->buffer[0]); 374 375 return IIO_VAL_INT; 376 } 377 378 static int max1027_read_raw(struct iio_dev *indio_dev, 379 struct iio_chan_spec const *chan, 380 int *val, int *val2, long mask) 381 { 382 int ret = 0; 383 struct max1027_state *st = iio_priv(indio_dev); 384 385 mutex_lock(&st->lock); 386 387 switch (mask) { 388 case IIO_CHAN_INFO_RAW: 389 ret = max1027_read_single_value(indio_dev, chan, val); 390 break; 391 case IIO_CHAN_INFO_SCALE: 392 switch (chan->type) { 393 case IIO_TEMP: 394 *val = 1; 395 *val2 = 8; 396 ret = IIO_VAL_FRACTIONAL; 397 break; 398 case IIO_VOLTAGE: 399 *val = 2500; 400 *val2 = chan->scan_type.realbits; 401 ret = IIO_VAL_FRACTIONAL_LOG2; 402 break; 403 default: 404 ret = -EINVAL; 405 break; 406 } 407 break; 408 default: 409 ret = -EINVAL; 410 break; 411 } 412 413 mutex_unlock(&st->lock); 414 415 return ret; 416 } 417 418 static int max1027_debugfs_reg_access(struct iio_dev *indio_dev, 419 unsigned int reg, unsigned int writeval, 420 unsigned int *readval) 421 { 422 struct max1027_state *st = iio_priv(indio_dev); 423 u8 *val = (u8 *)st->buffer; 424 425 if (readval) { 426 int ret = spi_read(st->spi, val, 2); 427 *readval = be16_to_cpu(st->buffer[0]); 428 return ret; 429 } 430 431 *val = (u8)writeval; 432 return spi_write(st->spi, val, 1); 433 } 434 435 static int max1027_set_cnvst_trigger_state(struct iio_trigger *trig, bool state) 436 { 437 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 438 int ret; 439 440 /* 441 * In order to disable the convst trigger, start acquisition on 442 * conversion register write, which basically disables triggering 443 * conversions upon cnvst changes and thus has the effect of disabling 444 * the external hardware trigger. 445 */ 446 ret = max1027_enable_trigger(indio_dev, state); 447 if (ret) 448 return ret; 449 450 if (state) { 451 ret = max1027_configure_chans_and_start(indio_dev); 452 if (ret) 453 return ret; 454 } 455 456 return 0; 457 } 458 459 static int max1027_read_scan(struct iio_dev *indio_dev) 460 { 461 struct max1027_state *st = iio_priv(indio_dev); 462 unsigned int scanned_chans; 463 int ret; 464 465 scanned_chans = fls(*indio_dev->active_scan_mask) - 1; 466 if (*indio_dev->active_scan_mask & MAX1X27_SCAN_MASK_TEMP) 467 scanned_chans++; 468 469 /* fill buffer with all channel */ 470 ret = spi_read(st->spi, st->buffer, scanned_chans * 2); 471 if (ret < 0) 472 return ret; 473 474 iio_push_to_buffers(indio_dev, st->buffer); 475 476 return 0; 477 } 478 479 static irqreturn_t max1027_handler(int irq, void *private) 480 { 481 struct iio_dev *indio_dev = private; 482 struct max1027_state *st = iio_priv(indio_dev); 483 484 /* 485 * If buffers are disabled (raw read) or when using external triggers, 486 * we just need to unlock the waiters which will then handle the data. 487 * 488 * When using the internal trigger, we must hand-off the choice of the 489 * handler to the core which will then lookup through the interrupt tree 490 * for the right handler registered with iio_triggered_buffer_setup() 491 * to execute, as this trigger might very well be used in conjunction 492 * with another device. The core will then call the relevant handler to 493 * perform the data processing step. 494 */ 495 if (!iio_buffer_enabled(indio_dev)) 496 complete(&st->complete); 497 else 498 iio_trigger_poll(indio_dev->trig); 499 500 return IRQ_HANDLED; 501 } 502 503 static irqreturn_t max1027_trigger_handler(int irq, void *private) 504 { 505 struct iio_poll_func *pf = private; 506 struct iio_dev *indio_dev = pf->indio_dev; 507 int ret; 508 509 if (!iio_trigger_using_own(indio_dev)) { 510 ret = max1027_configure_chans_and_start(indio_dev); 511 if (ret) 512 goto out; 513 514 /* This is a threaded handler, it is fine to wait for an IRQ */ 515 ret = max1027_wait_eoc(indio_dev); 516 if (ret) 517 goto out; 518 } 519 520 ret = max1027_read_scan(indio_dev); 521 out: 522 if (ret) 523 dev_err(&indio_dev->dev, 524 "Cannot read scanned values (%d)\n", ret); 525 526 iio_trigger_notify_done(indio_dev->trig); 527 528 return IRQ_HANDLED; 529 } 530 531 static const struct iio_trigger_ops max1027_trigger_ops = { 532 .validate_device = &iio_trigger_validate_own_device, 533 .set_trigger_state = &max1027_set_cnvst_trigger_state, 534 }; 535 536 static const struct iio_info max1027_info = { 537 .read_raw = &max1027_read_raw, 538 .debugfs_reg_access = &max1027_debugfs_reg_access, 539 }; 540 541 static int max1027_probe(struct spi_device *spi) 542 { 543 int ret; 544 struct iio_dev *indio_dev; 545 struct max1027_state *st; 546 547 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); 548 if (!indio_dev) { 549 pr_err("Can't allocate iio device\n"); 550 return -ENOMEM; 551 } 552 553 st = iio_priv(indio_dev); 554 st->spi = spi; 555 st->info = &max1027_chip_info_tbl[spi_get_device_id(spi)->driver_data]; 556 557 mutex_init(&st->lock); 558 init_completion(&st->complete); 559 560 indio_dev->name = spi_get_device_id(spi)->name; 561 indio_dev->info = &max1027_info; 562 indio_dev->modes = INDIO_DIRECT_MODE; 563 indio_dev->channels = st->info->channels; 564 indio_dev->num_channels = st->info->num_channels; 565 indio_dev->available_scan_masks = st->info->available_scan_masks; 566 567 st->buffer = devm_kmalloc_array(&indio_dev->dev, 568 indio_dev->num_channels, 2, 569 GFP_KERNEL); 570 if (!st->buffer) 571 return -ENOMEM; 572 573 /* Enable triggered buffers */ 574 ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev, 575 &iio_pollfunc_store_time, 576 &max1027_trigger_handler, 577 NULL); 578 if (ret < 0) { 579 dev_err(&indio_dev->dev, "Failed to setup buffer\n"); 580 return ret; 581 } 582 583 /* If there is an EOC interrupt, register the cnvst hardware trigger */ 584 if (spi->irq) { 585 st->trig = devm_iio_trigger_alloc(&spi->dev, "%s-trigger", 586 indio_dev->name); 587 if (!st->trig) { 588 ret = -ENOMEM; 589 dev_err(&indio_dev->dev, 590 "Failed to allocate iio trigger\n"); 591 return ret; 592 } 593 594 st->trig->ops = &max1027_trigger_ops; 595 iio_trigger_set_drvdata(st->trig, indio_dev); 596 ret = devm_iio_trigger_register(&indio_dev->dev, 597 st->trig); 598 if (ret < 0) { 599 dev_err(&indio_dev->dev, 600 "Failed to register iio trigger\n"); 601 return ret; 602 } 603 604 ret = devm_request_irq(&spi->dev, spi->irq, max1027_handler, 605 IRQF_TRIGGER_FALLING, 606 spi->dev.driver->name, indio_dev); 607 if (ret < 0) { 608 dev_err(&indio_dev->dev, "Failed to allocate IRQ.\n"); 609 return ret; 610 } 611 } 612 613 /* Internal reset */ 614 st->reg = MAX1027_RST_REG; 615 ret = spi_write(st->spi, &st->reg, 1); 616 if (ret < 0) { 617 dev_err(&indio_dev->dev, "Failed to reset the ADC\n"); 618 return ret; 619 } 620 621 /* Disable averaging */ 622 st->reg = MAX1027_AVG_REG; 623 ret = spi_write(st->spi, &st->reg, 1); 624 if (ret < 0) { 625 dev_err(&indio_dev->dev, "Failed to configure averaging register\n"); 626 return ret; 627 } 628 629 /* Assume conversion on register write for now */ 630 ret = max1027_enable_trigger(indio_dev, false); 631 if (ret) 632 return ret; 633 634 return devm_iio_device_register(&spi->dev, indio_dev); 635 } 636 637 static struct spi_driver max1027_driver = { 638 .driver = { 639 .name = "max1027", 640 .of_match_table = max1027_adc_dt_ids, 641 }, 642 .probe = max1027_probe, 643 .id_table = max1027_id, 644 }; 645 module_spi_driver(max1027_driver); 646 647 MODULE_AUTHOR("Philippe Reynes <tremyfr@yahoo.fr>"); 648 MODULE_DESCRIPTION("MAX1X27/MAX1X29/MAX1X31 ADC"); 649 MODULE_LICENSE("GPL v2"); 650