1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright 2016 Broadcom 4 */ 5 6 #include <linux/module.h> 7 #include <linux/mod_devicetable.h> 8 #include <linux/io.h> 9 #include <linux/clk.h> 10 #include <linux/mfd/syscon.h> 11 #include <linux/regmap.h> 12 #include <linux/delay.h> 13 #include <linux/interrupt.h> 14 #include <linux/platform_device.h> 15 16 #include <linux/iio/iio.h> 17 18 /* Below Register's are common to IPROC ADC and Touchscreen IP */ 19 #define IPROC_REGCTL1 0x00 20 #define IPROC_REGCTL2 0x04 21 #define IPROC_INTERRUPT_THRES 0x08 22 #define IPROC_INTERRUPT_MASK 0x0c 23 #define IPROC_INTERRUPT_STATUS 0x10 24 #define IPROC_ANALOG_CONTROL 0x1c 25 #define IPROC_CONTROLLER_STATUS 0x14 26 #define IPROC_AUX_DATA 0x20 27 #define IPROC_SOFT_BYPASS_CONTROL 0x38 28 #define IPROC_SOFT_BYPASS_DATA 0x3C 29 30 /* IPROC ADC Channel register offsets */ 31 #define IPROC_ADC_CHANNEL_REGCTL1 0x800 32 #define IPROC_ADC_CHANNEL_REGCTL2 0x804 33 #define IPROC_ADC_CHANNEL_STATUS 0x808 34 #define IPROC_ADC_CHANNEL_INTERRUPT_STATUS 0x80c 35 #define IPROC_ADC_CHANNEL_INTERRUPT_MASK 0x810 36 #define IPROC_ADC_CHANNEL_DATA 0x814 37 #define IPROC_ADC_CHANNEL_OFFSET 0x20 38 39 /* Bit definitions for IPROC_REGCTL2 */ 40 #define IPROC_ADC_AUXIN_SCAN_ENA BIT(0) 41 #define IPROC_ADC_PWR_LDO BIT(5) 42 #define IPROC_ADC_PWR_ADC BIT(4) 43 #define IPROC_ADC_PWR_BG BIT(3) 44 #define IPROC_ADC_CONTROLLER_EN BIT(17) 45 46 /* Bit definitions for IPROC_INTERRUPT_MASK and IPROC_INTERRUPT_STATUS */ 47 #define IPROC_ADC_AUXDATA_RDY_INTR BIT(3) 48 #define IPROC_ADC_INTR 9 49 #define IPROC_ADC_INTR_MASK (0xFF << IPROC_ADC_INTR) 50 51 /* Bit definitions for IPROC_ANALOG_CONTROL */ 52 #define IPROC_ADC_CHANNEL_SEL 11 53 #define IPROC_ADC_CHANNEL_SEL_MASK (0x7 << IPROC_ADC_CHANNEL_SEL) 54 55 /* Bit definitions for IPROC_ADC_CHANNEL_REGCTL1 */ 56 #define IPROC_ADC_CHANNEL_ROUNDS 0x2 57 #define IPROC_ADC_CHANNEL_ROUNDS_MASK (0x3F << IPROC_ADC_CHANNEL_ROUNDS) 58 #define IPROC_ADC_CHANNEL_MODE 0x1 59 #define IPROC_ADC_CHANNEL_MODE_MASK (0x1 << IPROC_ADC_CHANNEL_MODE) 60 #define IPROC_ADC_CHANNEL_MODE_TDM 0x1 61 #define IPROC_ADC_CHANNEL_MODE_SNAPSHOT 0x0 62 #define IPROC_ADC_CHANNEL_ENABLE 0x0 63 #define IPROC_ADC_CHANNEL_ENABLE_MASK 0x1 64 65 /* Bit definitions for IPROC_ADC_CHANNEL_REGCTL2 */ 66 #define IPROC_ADC_CHANNEL_WATERMARK 0x0 67 #define IPROC_ADC_CHANNEL_WATERMARK_MASK \ 68 (0x3F << IPROC_ADC_CHANNEL_WATERMARK) 69 70 #define IPROC_ADC_WATER_MARK_LEVEL 0x1 71 72 /* Bit definitions for IPROC_ADC_CHANNEL_STATUS */ 73 #define IPROC_ADC_CHANNEL_DATA_LOST 0x0 74 #define IPROC_ADC_CHANNEL_DATA_LOST_MASK \ 75 (0x0 << IPROC_ADC_CHANNEL_DATA_LOST) 76 #define IPROC_ADC_CHANNEL_VALID_ENTERIES 0x1 77 #define IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK \ 78 (0xFF << IPROC_ADC_CHANNEL_VALID_ENTERIES) 79 #define IPROC_ADC_CHANNEL_TOTAL_ENTERIES 0x9 80 #define IPROC_ADC_CHANNEL_TOTAL_ENTERIES_MASK \ 81 (0xFF << IPROC_ADC_CHANNEL_TOTAL_ENTERIES) 82 83 /* Bit definitions for IPROC_ADC_CHANNEL_INTERRUPT_MASK */ 84 #define IPROC_ADC_CHANNEL_WTRMRK_INTR 0x0 85 #define IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK \ 86 (0x1 << IPROC_ADC_CHANNEL_WTRMRK_INTR) 87 #define IPROC_ADC_CHANNEL_FULL_INTR 0x1 88 #define IPROC_ADC_CHANNEL_FULL_INTR_MASK \ 89 (0x1 << IPROC_ADC_IPROC_ADC_CHANNEL_FULL_INTR) 90 #define IPROC_ADC_CHANNEL_EMPTY_INTR 0x2 91 #define IPROC_ADC_CHANNEL_EMPTY_INTR_MASK \ 92 (0x1 << IPROC_ADC_CHANNEL_EMPTY_INTR) 93 94 #define IPROC_ADC_WATER_MARK_INTR_ENABLE 0x1 95 96 /* Number of time to retry a set of the interrupt mask reg */ 97 #define IPROC_ADC_INTMASK_RETRY_ATTEMPTS 10 98 99 #define IPROC_ADC_READ_TIMEOUT (HZ*2) 100 101 #define iproc_adc_dbg_reg(dev, priv, reg) \ 102 do { \ 103 u32 val; \ 104 regmap_read(priv->regmap, reg, &val); \ 105 dev_dbg(dev, "%20s= 0x%08x\n", #reg, val); \ 106 } while (0) 107 108 struct iproc_adc_priv { 109 struct regmap *regmap; 110 struct clk *adc_clk; 111 struct mutex mutex; 112 int irqno; 113 int chan_val; 114 int chan_id; 115 struct completion completion; 116 }; 117 118 static void iproc_adc_reg_dump(struct iio_dev *indio_dev) 119 { 120 struct device *dev = &indio_dev->dev; 121 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 122 123 iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL1); 124 iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL2); 125 iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_THRES); 126 iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_MASK); 127 iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_STATUS); 128 iproc_adc_dbg_reg(dev, adc_priv, IPROC_CONTROLLER_STATUS); 129 iproc_adc_dbg_reg(dev, adc_priv, IPROC_ANALOG_CONTROL); 130 iproc_adc_dbg_reg(dev, adc_priv, IPROC_AUX_DATA); 131 iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_CONTROL); 132 iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_DATA); 133 } 134 135 static irqreturn_t iproc_adc_interrupt_thread(int irq, void *data) 136 { 137 u32 channel_intr_status; 138 u32 intr_status; 139 u32 intr_mask; 140 struct iio_dev *indio_dev = data; 141 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 142 143 /* 144 * This interrupt is shared with the touchscreen driver. 145 * Make sure this interrupt is intended for us. 146 * Handle only ADC channel specific interrupts. 147 */ 148 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status); 149 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &intr_mask); 150 intr_status = intr_status & intr_mask; 151 channel_intr_status = (intr_status & IPROC_ADC_INTR_MASK) >> 152 IPROC_ADC_INTR; 153 if (channel_intr_status) 154 return IRQ_WAKE_THREAD; 155 156 return IRQ_NONE; 157 } 158 159 static irqreturn_t iproc_adc_interrupt_handler(int irq, void *data) 160 { 161 irqreturn_t retval = IRQ_NONE; 162 struct iproc_adc_priv *adc_priv; 163 struct iio_dev *indio_dev = data; 164 unsigned int valid_entries; 165 u32 intr_status; 166 u32 intr_channels; 167 u32 channel_status; 168 u32 ch_intr_status; 169 170 adc_priv = iio_priv(indio_dev); 171 172 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status); 173 dev_dbg(&indio_dev->dev, "iproc_adc_interrupt_handler(),INTRPT_STS:%x\n", 174 intr_status); 175 176 intr_channels = (intr_status & IPROC_ADC_INTR_MASK) >> IPROC_ADC_INTR; 177 if (intr_channels) { 178 regmap_read(adc_priv->regmap, 179 IPROC_ADC_CHANNEL_INTERRUPT_STATUS + 180 IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id, 181 &ch_intr_status); 182 183 if (ch_intr_status & IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK) { 184 regmap_read(adc_priv->regmap, 185 IPROC_ADC_CHANNEL_STATUS + 186 IPROC_ADC_CHANNEL_OFFSET * 187 adc_priv->chan_id, 188 &channel_status); 189 190 valid_entries = ((channel_status & 191 IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK) >> 192 IPROC_ADC_CHANNEL_VALID_ENTERIES); 193 if (valid_entries >= 1) { 194 regmap_read(adc_priv->regmap, 195 IPROC_ADC_CHANNEL_DATA + 196 IPROC_ADC_CHANNEL_OFFSET * 197 adc_priv->chan_id, 198 &adc_priv->chan_val); 199 complete(&adc_priv->completion); 200 } else { 201 dev_err(&indio_dev->dev, 202 "No data rcvd on channel %d\n", 203 adc_priv->chan_id); 204 } 205 regmap_write(adc_priv->regmap, 206 IPROC_ADC_CHANNEL_INTERRUPT_MASK + 207 IPROC_ADC_CHANNEL_OFFSET * 208 adc_priv->chan_id, 209 (ch_intr_status & 210 ~(IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK))); 211 } 212 regmap_write(adc_priv->regmap, 213 IPROC_ADC_CHANNEL_INTERRUPT_STATUS + 214 IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id, 215 ch_intr_status); 216 regmap_write(adc_priv->regmap, IPROC_INTERRUPT_STATUS, 217 intr_channels); 218 retval = IRQ_HANDLED; 219 } 220 221 return retval; 222 } 223 224 static int iproc_adc_do_read(struct iio_dev *indio_dev, 225 int channel, 226 u16 *p_adc_data) 227 { 228 int read_len = 0; 229 u32 val; 230 u32 mask; 231 u32 val_check; 232 int failed_cnt = 0; 233 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 234 235 mutex_lock(&adc_priv->mutex); 236 237 /* 238 * After a read is complete the ADC interrupts will be disabled so 239 * we can assume this section of code is safe from interrupts. 240 */ 241 adc_priv->chan_val = -1; 242 adc_priv->chan_id = channel; 243 244 reinit_completion(&adc_priv->completion); 245 /* Clear any pending interrupt */ 246 regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS, 247 IPROC_ADC_INTR_MASK | IPROC_ADC_AUXDATA_RDY_INTR, 248 ((0x0 << channel) << IPROC_ADC_INTR) | 249 IPROC_ADC_AUXDATA_RDY_INTR); 250 251 /* Configure channel for snapshot mode and enable */ 252 val = (BIT(IPROC_ADC_CHANNEL_ROUNDS) | 253 (IPROC_ADC_CHANNEL_MODE_SNAPSHOT << IPROC_ADC_CHANNEL_MODE) | 254 (0x1 << IPROC_ADC_CHANNEL_ENABLE)); 255 256 mask = IPROC_ADC_CHANNEL_ROUNDS_MASK | IPROC_ADC_CHANNEL_MODE_MASK | 257 IPROC_ADC_CHANNEL_ENABLE_MASK; 258 regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL1 + 259 IPROC_ADC_CHANNEL_OFFSET * channel), 260 mask, val); 261 262 /* Set the Watermark for a channel */ 263 regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL2 + 264 IPROC_ADC_CHANNEL_OFFSET * channel), 265 IPROC_ADC_CHANNEL_WATERMARK_MASK, 266 0x1); 267 268 /* Enable water mark interrupt */ 269 regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_INTERRUPT_MASK + 270 IPROC_ADC_CHANNEL_OFFSET * 271 channel), 272 IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK, 273 IPROC_ADC_WATER_MARK_INTR_ENABLE); 274 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val); 275 276 /* Enable ADC interrupt for a channel */ 277 val |= (BIT(channel) << IPROC_ADC_INTR); 278 regmap_write(adc_priv->regmap, IPROC_INTERRUPT_MASK, val); 279 280 /* 281 * There seems to be a very rare issue where writing to this register 282 * does not take effect. To work around the issue we will try multiple 283 * writes. In total we will spend about 10*10 = 100 us attempting this. 284 * Testing has shown that this may loop a few time, but we have never 285 * hit the full count. 286 */ 287 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); 288 while (val_check != val) { 289 failed_cnt++; 290 291 if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS) 292 break; 293 294 udelay(10); 295 regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK, 296 IPROC_ADC_INTR_MASK, 297 ((0x1 << channel) << 298 IPROC_ADC_INTR)); 299 300 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); 301 } 302 303 if (failed_cnt) { 304 dev_dbg(&indio_dev->dev, 305 "IntMask failed (%d times)", failed_cnt); 306 if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS) { 307 dev_err(&indio_dev->dev, 308 "IntMask set failed. Read will likely fail."); 309 read_len = -EIO; 310 goto adc_err; 311 } 312 } 313 regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check); 314 315 if (wait_for_completion_timeout(&adc_priv->completion, 316 IPROC_ADC_READ_TIMEOUT) > 0) { 317 318 /* Only the lower 16 bits are relevant */ 319 *p_adc_data = adc_priv->chan_val & 0xFFFF; 320 read_len = sizeof(*p_adc_data); 321 322 } else { 323 /* 324 * We never got the interrupt, something went wrong. 325 * Perhaps the interrupt may still be coming, we do not want 326 * that now. Lets disable the ADC interrupt, and clear the 327 * status to put it back in to normal state. 328 */ 329 read_len = -ETIMEDOUT; 330 goto adc_err; 331 } 332 mutex_unlock(&adc_priv->mutex); 333 334 return read_len; 335 336 adc_err: 337 regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK, 338 IPROC_ADC_INTR_MASK, 339 ((0x0 << channel) << IPROC_ADC_INTR)); 340 341 regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS, 342 IPROC_ADC_INTR_MASK, 343 ((0x0 << channel) << IPROC_ADC_INTR)); 344 345 dev_err(&indio_dev->dev, "Timed out waiting for ADC data!\n"); 346 iproc_adc_reg_dump(indio_dev); 347 mutex_unlock(&adc_priv->mutex); 348 349 return read_len; 350 } 351 352 static int iproc_adc_enable(struct iio_dev *indio_dev) 353 { 354 u32 val; 355 u32 channel_id; 356 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 357 int ret; 358 359 /* Set i_amux = 3b'000, select channel 0 */ 360 ret = regmap_update_bits(adc_priv->regmap, IPROC_ANALOG_CONTROL, 361 IPROC_ADC_CHANNEL_SEL_MASK, 0); 362 if (ret) { 363 dev_err(&indio_dev->dev, 364 "failed to write IPROC_ANALOG_CONTROL %d\n", ret); 365 return ret; 366 } 367 adc_priv->chan_val = -1; 368 369 /* 370 * PWR up LDO, ADC, and Band Gap (0 to enable) 371 * Also enable ADC controller (set high) 372 */ 373 ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); 374 if (ret) { 375 dev_err(&indio_dev->dev, 376 "failed to read IPROC_REGCTL2 %d\n", ret); 377 return ret; 378 } 379 380 val &= ~(IPROC_ADC_PWR_LDO | IPROC_ADC_PWR_ADC | IPROC_ADC_PWR_BG); 381 382 ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); 383 if (ret) { 384 dev_err(&indio_dev->dev, 385 "failed to write IPROC_REGCTL2 %d\n", ret); 386 return ret; 387 } 388 389 ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); 390 if (ret) { 391 dev_err(&indio_dev->dev, 392 "failed to read IPROC_REGCTL2 %d\n", ret); 393 return ret; 394 } 395 396 val |= IPROC_ADC_CONTROLLER_EN; 397 ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); 398 if (ret) { 399 dev_err(&indio_dev->dev, 400 "failed to write IPROC_REGCTL2 %d\n", ret); 401 return ret; 402 } 403 404 for (channel_id = 0; channel_id < indio_dev->num_channels; 405 channel_id++) { 406 ret = regmap_write(adc_priv->regmap, 407 IPROC_ADC_CHANNEL_INTERRUPT_MASK + 408 IPROC_ADC_CHANNEL_OFFSET * channel_id, 0); 409 if (ret) { 410 dev_err(&indio_dev->dev, 411 "failed to write ADC_CHANNEL_INTERRUPT_MASK %d\n", 412 ret); 413 return ret; 414 } 415 416 ret = regmap_write(adc_priv->regmap, 417 IPROC_ADC_CHANNEL_INTERRUPT_STATUS + 418 IPROC_ADC_CHANNEL_OFFSET * channel_id, 0); 419 if (ret) { 420 dev_err(&indio_dev->dev, 421 "failed to write ADC_CHANNEL_INTERRUPT_STATUS %d\n", 422 ret); 423 return ret; 424 } 425 } 426 427 return 0; 428 } 429 430 static void iproc_adc_disable(struct iio_dev *indio_dev) 431 { 432 u32 val; 433 int ret; 434 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 435 436 ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val); 437 if (ret) { 438 dev_err(&indio_dev->dev, 439 "failed to read IPROC_REGCTL2 %d\n", ret); 440 return; 441 } 442 443 val &= ~IPROC_ADC_CONTROLLER_EN; 444 ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val); 445 if (ret) { 446 dev_err(&indio_dev->dev, 447 "failed to write IPROC_REGCTL2 %d\n", ret); 448 return; 449 } 450 } 451 452 static int iproc_adc_read_raw(struct iio_dev *indio_dev, 453 struct iio_chan_spec const *chan, 454 int *val, 455 int *val2, 456 long mask) 457 { 458 u16 adc_data; 459 int err; 460 461 switch (mask) { 462 case IIO_CHAN_INFO_RAW: 463 err = iproc_adc_do_read(indio_dev, chan->channel, &adc_data); 464 if (err < 0) 465 return err; 466 *val = adc_data; 467 return IIO_VAL_INT; 468 case IIO_CHAN_INFO_SCALE: 469 switch (chan->type) { 470 case IIO_VOLTAGE: 471 *val = 1800; 472 *val2 = 10; 473 return IIO_VAL_FRACTIONAL_LOG2; 474 default: 475 return -EINVAL; 476 } 477 default: 478 return -EINVAL; 479 } 480 } 481 482 static const struct iio_info iproc_adc_iio_info = { 483 .read_raw = &iproc_adc_read_raw, 484 }; 485 486 #define IPROC_ADC_CHANNEL(_index, _id) { \ 487 .type = IIO_VOLTAGE, \ 488 .indexed = 1, \ 489 .channel = _index, \ 490 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 491 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 492 .datasheet_name = _id, \ 493 } 494 495 static const struct iio_chan_spec iproc_adc_iio_channels[] = { 496 IPROC_ADC_CHANNEL(0, "adc0"), 497 IPROC_ADC_CHANNEL(1, "adc1"), 498 IPROC_ADC_CHANNEL(2, "adc2"), 499 IPROC_ADC_CHANNEL(3, "adc3"), 500 IPROC_ADC_CHANNEL(4, "adc4"), 501 IPROC_ADC_CHANNEL(5, "adc5"), 502 IPROC_ADC_CHANNEL(6, "adc6"), 503 IPROC_ADC_CHANNEL(7, "adc7"), 504 }; 505 506 static int iproc_adc_probe(struct platform_device *pdev) 507 { 508 struct iproc_adc_priv *adc_priv; 509 struct iio_dev *indio_dev = NULL; 510 int ret; 511 512 indio_dev = devm_iio_device_alloc(&pdev->dev, 513 sizeof(*adc_priv)); 514 if (!indio_dev) { 515 dev_err(&pdev->dev, "failed to allocate iio device\n"); 516 return -ENOMEM; 517 } 518 519 adc_priv = iio_priv(indio_dev); 520 platform_set_drvdata(pdev, indio_dev); 521 522 mutex_init(&adc_priv->mutex); 523 524 init_completion(&adc_priv->completion); 525 526 adc_priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, 527 "adc-syscon"); 528 if (IS_ERR(adc_priv->regmap)) { 529 dev_err(&pdev->dev, "failed to get handle for tsc syscon\n"); 530 ret = PTR_ERR(adc_priv->regmap); 531 return ret; 532 } 533 534 adc_priv->adc_clk = devm_clk_get(&pdev->dev, "tsc_clk"); 535 if (IS_ERR(adc_priv->adc_clk)) { 536 dev_err(&pdev->dev, 537 "failed getting clock tsc_clk\n"); 538 ret = PTR_ERR(adc_priv->adc_clk); 539 return ret; 540 } 541 542 adc_priv->irqno = platform_get_irq(pdev, 0); 543 if (adc_priv->irqno <= 0) 544 return -ENODEV; 545 546 ret = regmap_update_bits(adc_priv->regmap, IPROC_REGCTL2, 547 IPROC_ADC_AUXIN_SCAN_ENA, 0); 548 if (ret) { 549 dev_err(&pdev->dev, "failed to write IPROC_REGCTL2 %d\n", ret); 550 return ret; 551 } 552 553 ret = devm_request_threaded_irq(&pdev->dev, adc_priv->irqno, 554 iproc_adc_interrupt_handler, 555 iproc_adc_interrupt_thread, 556 IRQF_SHARED, "iproc-adc", indio_dev); 557 if (ret) { 558 dev_err(&pdev->dev, "request_irq error %d\n", ret); 559 return ret; 560 } 561 562 ret = clk_prepare_enable(adc_priv->adc_clk); 563 if (ret) { 564 dev_err(&pdev->dev, 565 "clk_prepare_enable failed %d\n", ret); 566 return ret; 567 } 568 569 ret = iproc_adc_enable(indio_dev); 570 if (ret) { 571 dev_err(&pdev->dev, "failed to enable adc %d\n", ret); 572 goto err_adc_enable; 573 } 574 575 indio_dev->name = "iproc-static-adc"; 576 indio_dev->info = &iproc_adc_iio_info; 577 indio_dev->modes = INDIO_DIRECT_MODE; 578 indio_dev->channels = iproc_adc_iio_channels; 579 indio_dev->num_channels = ARRAY_SIZE(iproc_adc_iio_channels); 580 581 ret = iio_device_register(indio_dev); 582 if (ret) { 583 dev_err(&pdev->dev, "iio_device_register failed:err %d\n", ret); 584 goto err_clk; 585 } 586 587 return 0; 588 589 err_clk: 590 iproc_adc_disable(indio_dev); 591 err_adc_enable: 592 clk_disable_unprepare(adc_priv->adc_clk); 593 594 return ret; 595 } 596 597 static int iproc_adc_remove(struct platform_device *pdev) 598 { 599 struct iio_dev *indio_dev = platform_get_drvdata(pdev); 600 struct iproc_adc_priv *adc_priv = iio_priv(indio_dev); 601 602 iio_device_unregister(indio_dev); 603 iproc_adc_disable(indio_dev); 604 clk_disable_unprepare(adc_priv->adc_clk); 605 606 return 0; 607 } 608 609 static const struct of_device_id iproc_adc_of_match[] = { 610 {.compatible = "brcm,iproc-static-adc", }, 611 { }, 612 }; 613 MODULE_DEVICE_TABLE(of, iproc_adc_of_match); 614 615 static struct platform_driver iproc_adc_driver = { 616 .probe = iproc_adc_probe, 617 .remove = iproc_adc_remove, 618 .driver = { 619 .name = "iproc-static-adc", 620 .of_match_table = iproc_adc_of_match, 621 }, 622 }; 623 module_platform_driver(iproc_adc_driver); 624 625 MODULE_DESCRIPTION("Broadcom iProc ADC controller driver"); 626 MODULE_AUTHOR("Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>"); 627 MODULE_LICENSE("GPL v2"); 628