1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * AD7904/AD7914/AD7923/AD7924/AD7908/AD7918/AD7928 SPI ADC driver 4 * 5 * Copyright 2011 Analog Devices Inc (from AD7923 Driver) 6 * Copyright 2012 CS Systemes d'Information 7 */ 8 9 #include <linux/device.h> 10 #include <linux/kernel.h> 11 #include <linux/slab.h> 12 #include <linux/sysfs.h> 13 #include <linux/spi/spi.h> 14 #include <linux/regulator/consumer.h> 15 #include <linux/err.h> 16 #include <linux/delay.h> 17 #include <linux/module.h> 18 #include <linux/interrupt.h> 19 20 #include <linux/iio/iio.h> 21 #include <linux/iio/sysfs.h> 22 #include <linux/iio/buffer.h> 23 #include <linux/iio/trigger_consumer.h> 24 #include <linux/iio/triggered_buffer.h> 25 26 #define AD7923_WRITE_CR BIT(11) /* write control register */ 27 #define AD7923_RANGE BIT(1) /* range to REFin */ 28 #define AD7923_CODING BIT(0) /* coding is straight binary */ 29 #define AD7923_PM_MODE_AS (1) /* auto shutdown */ 30 #define AD7923_PM_MODE_FS (2) /* full shutdown */ 31 #define AD7923_PM_MODE_OPS (3) /* normal operation */ 32 #define AD7923_SEQUENCE_OFF (0) /* no sequence fonction */ 33 #define AD7923_SEQUENCE_PROTECT (2) /* no interrupt write cycle */ 34 #define AD7923_SEQUENCE_ON (3) /* continuous sequence */ 35 36 37 #define AD7923_PM_MODE_WRITE(mode) ((mode) << 4) /* write mode */ 38 #define AD7923_CHANNEL_WRITE(channel) ((channel) << 6) /* write channel */ 39 #define AD7923_SEQUENCE_WRITE(sequence) ((((sequence) & 1) << 3) \ 40 + (((sequence) & 2) << 9)) 41 /* write sequence fonction */ 42 /* left shift for CR : bit 11 transmit in first */ 43 #define AD7923_SHIFT_REGISTER 4 44 45 /* val = value, dec = left shift, bits = number of bits of the mask */ 46 #define EXTRACT(val, dec, bits) (((val) >> (dec)) & ((1 << (bits)) - 1)) 47 48 struct ad7923_state { 49 struct spi_device *spi; 50 struct spi_transfer ring_xfer[5]; 51 struct spi_transfer scan_single_xfer[2]; 52 struct spi_message ring_msg; 53 struct spi_message scan_single_msg; 54 55 struct regulator *reg; 56 57 unsigned int settings; 58 59 /* 60 * DMA (thus cache coherency maintenance) requires the 61 * transfer buffers to live in their own cache lines. 62 * Ensure rx_buf can be directly used in iio_push_to_buffers_with_timetamp 63 * Length = 8 channels + 4 extra for 8 byte timestamp 64 */ 65 __be16 rx_buf[12] ____cacheline_aligned; 66 __be16 tx_buf[4]; 67 }; 68 69 struct ad7923_chip_info { 70 const struct iio_chan_spec *channels; 71 unsigned int num_channels; 72 }; 73 74 enum ad7923_id { 75 AD7904, 76 AD7914, 77 AD7924, 78 AD7908, 79 AD7918, 80 AD7928 81 }; 82 83 #define AD7923_V_CHAN(index, bits) \ 84 { \ 85 .type = IIO_VOLTAGE, \ 86 .indexed = 1, \ 87 .channel = index, \ 88 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 89 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 90 .address = index, \ 91 .scan_index = index, \ 92 .scan_type = { \ 93 .sign = 'u', \ 94 .realbits = (bits), \ 95 .storagebits = 16, \ 96 .endianness = IIO_BE, \ 97 }, \ 98 } 99 100 #define DECLARE_AD7923_CHANNELS(name, bits) \ 101 const struct iio_chan_spec name ## _channels[] = { \ 102 AD7923_V_CHAN(0, bits), \ 103 AD7923_V_CHAN(1, bits), \ 104 AD7923_V_CHAN(2, bits), \ 105 AD7923_V_CHAN(3, bits), \ 106 IIO_CHAN_SOFT_TIMESTAMP(4), \ 107 } 108 109 #define DECLARE_AD7908_CHANNELS(name, bits) \ 110 const struct iio_chan_spec name ## _channels[] = { \ 111 AD7923_V_CHAN(0, bits), \ 112 AD7923_V_CHAN(1, bits), \ 113 AD7923_V_CHAN(2, bits), \ 114 AD7923_V_CHAN(3, bits), \ 115 AD7923_V_CHAN(4, bits), \ 116 AD7923_V_CHAN(5, bits), \ 117 AD7923_V_CHAN(6, bits), \ 118 AD7923_V_CHAN(7, bits), \ 119 IIO_CHAN_SOFT_TIMESTAMP(8), \ 120 } 121 122 static DECLARE_AD7923_CHANNELS(ad7904, 8); 123 static DECLARE_AD7923_CHANNELS(ad7914, 10); 124 static DECLARE_AD7923_CHANNELS(ad7924, 12); 125 static DECLARE_AD7908_CHANNELS(ad7908, 8); 126 static DECLARE_AD7908_CHANNELS(ad7918, 10); 127 static DECLARE_AD7908_CHANNELS(ad7928, 12); 128 129 static const struct ad7923_chip_info ad7923_chip_info[] = { 130 [AD7904] = { 131 .channels = ad7904_channels, 132 .num_channels = ARRAY_SIZE(ad7904_channels), 133 }, 134 [AD7914] = { 135 .channels = ad7914_channels, 136 .num_channels = ARRAY_SIZE(ad7914_channels), 137 }, 138 [AD7924] = { 139 .channels = ad7924_channels, 140 .num_channels = ARRAY_SIZE(ad7924_channels), 141 }, 142 [AD7908] = { 143 .channels = ad7908_channels, 144 .num_channels = ARRAY_SIZE(ad7908_channels), 145 }, 146 [AD7918] = { 147 .channels = ad7918_channels, 148 .num_channels = ARRAY_SIZE(ad7918_channels), 149 }, 150 [AD7928] = { 151 .channels = ad7928_channels, 152 .num_channels = ARRAY_SIZE(ad7928_channels), 153 }, 154 }; 155 156 /* 157 * ad7923_update_scan_mode() setup the spi transfer buffer for the new scan mask 158 */ 159 static int ad7923_update_scan_mode(struct iio_dev *indio_dev, 160 const unsigned long *active_scan_mask) 161 { 162 struct ad7923_state *st = iio_priv(indio_dev); 163 int i, cmd, len; 164 165 len = 0; 166 /* 167 * For this driver the last channel is always the software timestamp so 168 * skip that one. 169 */ 170 for_each_set_bit(i, active_scan_mask, indio_dev->num_channels - 1) { 171 cmd = AD7923_WRITE_CR | AD7923_CHANNEL_WRITE(i) | 172 AD7923_SEQUENCE_WRITE(AD7923_SEQUENCE_OFF) | 173 st->settings; 174 cmd <<= AD7923_SHIFT_REGISTER; 175 st->tx_buf[len++] = cpu_to_be16(cmd); 176 } 177 /* build spi ring message */ 178 st->ring_xfer[0].tx_buf = &st->tx_buf[0]; 179 st->ring_xfer[0].len = len; 180 st->ring_xfer[0].cs_change = 1; 181 182 spi_message_init(&st->ring_msg); 183 spi_message_add_tail(&st->ring_xfer[0], &st->ring_msg); 184 185 for (i = 0; i < len; i++) { 186 st->ring_xfer[i + 1].rx_buf = &st->rx_buf[i]; 187 st->ring_xfer[i + 1].len = 2; 188 st->ring_xfer[i + 1].cs_change = 1; 189 spi_message_add_tail(&st->ring_xfer[i + 1], &st->ring_msg); 190 } 191 /* make sure last transfer cs_change is not set */ 192 st->ring_xfer[i + 1].cs_change = 0; 193 194 return 0; 195 } 196 197 static irqreturn_t ad7923_trigger_handler(int irq, void *p) 198 { 199 struct iio_poll_func *pf = p; 200 struct iio_dev *indio_dev = pf->indio_dev; 201 struct ad7923_state *st = iio_priv(indio_dev); 202 int b_sent; 203 204 b_sent = spi_sync(st->spi, &st->ring_msg); 205 if (b_sent) 206 goto done; 207 208 iio_push_to_buffers_with_timestamp(indio_dev, st->rx_buf, 209 iio_get_time_ns(indio_dev)); 210 211 done: 212 iio_trigger_notify_done(indio_dev->trig); 213 214 return IRQ_HANDLED; 215 } 216 217 static int ad7923_scan_direct(struct ad7923_state *st, unsigned int ch) 218 { 219 int ret, cmd; 220 221 cmd = AD7923_WRITE_CR | AD7923_CHANNEL_WRITE(ch) | 222 AD7923_SEQUENCE_WRITE(AD7923_SEQUENCE_OFF) | 223 st->settings; 224 cmd <<= AD7923_SHIFT_REGISTER; 225 st->tx_buf[0] = cpu_to_be16(cmd); 226 227 ret = spi_sync(st->spi, &st->scan_single_msg); 228 if (ret) 229 return ret; 230 231 return be16_to_cpu(st->rx_buf[0]); 232 } 233 234 static int ad7923_get_range(struct ad7923_state *st) 235 { 236 int vref; 237 238 vref = regulator_get_voltage(st->reg); 239 if (vref < 0) 240 return vref; 241 242 vref /= 1000; 243 244 if (!(st->settings & AD7923_RANGE)) 245 vref *= 2; 246 247 return vref; 248 } 249 250 static int ad7923_read_raw(struct iio_dev *indio_dev, 251 struct iio_chan_spec const *chan, 252 int *val, 253 int *val2, 254 long m) 255 { 256 int ret; 257 struct ad7923_state *st = iio_priv(indio_dev); 258 259 switch (m) { 260 case IIO_CHAN_INFO_RAW: 261 ret = iio_device_claim_direct_mode(indio_dev); 262 if (ret) 263 return ret; 264 ret = ad7923_scan_direct(st, chan->address); 265 iio_device_release_direct_mode(indio_dev); 266 267 if (ret < 0) 268 return ret; 269 270 if (chan->address == EXTRACT(ret, 12, 4)) 271 *val = EXTRACT(ret, 0, 12); 272 else 273 return -EIO; 274 275 return IIO_VAL_INT; 276 case IIO_CHAN_INFO_SCALE: 277 ret = ad7923_get_range(st); 278 if (ret < 0) 279 return ret; 280 *val = ret; 281 *val2 = chan->scan_type.realbits; 282 return IIO_VAL_FRACTIONAL_LOG2; 283 } 284 return -EINVAL; 285 } 286 287 static const struct iio_info ad7923_info = { 288 .read_raw = &ad7923_read_raw, 289 .update_scan_mode = ad7923_update_scan_mode, 290 }; 291 292 static void ad7923_regulator_disable(void *data) 293 { 294 struct ad7923_state *st = data; 295 296 regulator_disable(st->reg); 297 } 298 299 static int ad7923_probe(struct spi_device *spi) 300 { 301 struct ad7923_state *st; 302 struct iio_dev *indio_dev; 303 const struct ad7923_chip_info *info; 304 int ret; 305 306 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); 307 if (!indio_dev) 308 return -ENOMEM; 309 310 st = iio_priv(indio_dev); 311 312 st->spi = spi; 313 st->settings = AD7923_CODING | AD7923_RANGE | 314 AD7923_PM_MODE_WRITE(AD7923_PM_MODE_OPS); 315 316 info = &ad7923_chip_info[spi_get_device_id(spi)->driver_data]; 317 318 indio_dev->name = spi_get_device_id(spi)->name; 319 indio_dev->modes = INDIO_DIRECT_MODE; 320 indio_dev->channels = info->channels; 321 indio_dev->num_channels = info->num_channels; 322 indio_dev->info = &ad7923_info; 323 324 /* Setup default message */ 325 326 st->scan_single_xfer[0].tx_buf = &st->tx_buf[0]; 327 st->scan_single_xfer[0].len = 2; 328 st->scan_single_xfer[0].cs_change = 1; 329 st->scan_single_xfer[1].rx_buf = &st->rx_buf[0]; 330 st->scan_single_xfer[1].len = 2; 331 332 spi_message_init(&st->scan_single_msg); 333 spi_message_add_tail(&st->scan_single_xfer[0], &st->scan_single_msg); 334 spi_message_add_tail(&st->scan_single_xfer[1], &st->scan_single_msg); 335 336 st->reg = devm_regulator_get(&spi->dev, "refin"); 337 if (IS_ERR(st->reg)) 338 return PTR_ERR(st->reg); 339 340 ret = regulator_enable(st->reg); 341 if (ret) 342 return ret; 343 344 ret = devm_add_action_or_reset(&spi->dev, ad7923_regulator_disable, st); 345 if (ret) 346 return ret; 347 348 ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev, NULL, 349 &ad7923_trigger_handler, NULL); 350 if (ret) 351 return ret; 352 353 return devm_iio_device_register(&spi->dev, indio_dev); 354 } 355 356 static const struct spi_device_id ad7923_id[] = { 357 {"ad7904", AD7904}, 358 {"ad7914", AD7914}, 359 {"ad7923", AD7924}, 360 {"ad7924", AD7924}, 361 {"ad7908", AD7908}, 362 {"ad7918", AD7918}, 363 {"ad7928", AD7928}, 364 {} 365 }; 366 MODULE_DEVICE_TABLE(spi, ad7923_id); 367 368 static const struct of_device_id ad7923_of_match[] = { 369 { .compatible = "adi,ad7904", }, 370 { .compatible = "adi,ad7914", }, 371 { .compatible = "adi,ad7923", }, 372 { .compatible = "adi,ad7924", }, 373 { .compatible = "adi,ad7908", }, 374 { .compatible = "adi,ad7918", }, 375 { .compatible = "adi,ad7928", }, 376 { }, 377 }; 378 MODULE_DEVICE_TABLE(of, ad7923_of_match); 379 380 static struct spi_driver ad7923_driver = { 381 .driver = { 382 .name = "ad7923", 383 .of_match_table = ad7923_of_match, 384 }, 385 .probe = ad7923_probe, 386 .id_table = ad7923_id, 387 }; 388 module_spi_driver(ad7923_driver); 389 390 MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); 391 MODULE_AUTHOR("Patrick Vasseur <patrick.vasseur@c-s.fr>"); 392 MODULE_DESCRIPTION("Analog Devices AD7923 and similar ADC"); 393 MODULE_LICENSE("GPL v2"); 394