1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * AD7190 AD7192 AD7193 AD7195 SPI ADC driver 4 * 5 * Copyright 2011-2015 Analog Devices Inc. 6 */ 7 8 #include <linux/interrupt.h> 9 #include <linux/clk.h> 10 #include <linux/device.h> 11 #include <linux/kernel.h> 12 #include <linux/slab.h> 13 #include <linux/sysfs.h> 14 #include <linux/spi/spi.h> 15 #include <linux/regulator/consumer.h> 16 #include <linux/err.h> 17 #include <linux/sched.h> 18 #include <linux/delay.h> 19 #include <linux/of.h> 20 21 #include <linux/iio/iio.h> 22 #include <linux/iio/sysfs.h> 23 #include <linux/iio/buffer.h> 24 #include <linux/iio/trigger.h> 25 #include <linux/iio/trigger_consumer.h> 26 #include <linux/iio/triggered_buffer.h> 27 #include <linux/iio/adc/ad_sigma_delta.h> 28 29 /* Registers */ 30 #define AD7192_REG_COMM 0 /* Communications Register (WO, 8-bit) */ 31 #define AD7192_REG_STAT 0 /* Status Register (RO, 8-bit) */ 32 #define AD7192_REG_MODE 1 /* Mode Register (RW, 24-bit */ 33 #define AD7192_REG_CONF 2 /* Configuration Register (RW, 24-bit) */ 34 #define AD7192_REG_DATA 3 /* Data Register (RO, 24/32-bit) */ 35 #define AD7192_REG_ID 4 /* ID Register (RO, 8-bit) */ 36 #define AD7192_REG_GPOCON 5 /* GPOCON Register (RO, 8-bit) */ 37 #define AD7192_REG_OFFSET 6 /* Offset Register (RW, 16-bit */ 38 /* (AD7792)/24-bit (AD7192)) */ 39 #define AD7192_REG_FULLSALE 7 /* Full-Scale Register */ 40 /* (RW, 16-bit (AD7792)/24-bit (AD7192)) */ 41 42 /* Communications Register Bit Designations (AD7192_REG_COMM) */ 43 #define AD7192_COMM_WEN BIT(7) /* Write Enable */ 44 #define AD7192_COMM_WRITE 0 /* Write Operation */ 45 #define AD7192_COMM_READ BIT(6) /* Read Operation */ 46 #define AD7192_COMM_ADDR(x) (((x) & 0x7) << 3) /* Register Address */ 47 #define AD7192_COMM_CREAD BIT(2) /* Continuous Read of Data Register */ 48 49 /* Status Register Bit Designations (AD7192_REG_STAT) */ 50 #define AD7192_STAT_RDY BIT(7) /* Ready */ 51 #define AD7192_STAT_ERR BIT(6) /* Error (Overrange, Underrange) */ 52 #define AD7192_STAT_NOREF BIT(5) /* Error no external reference */ 53 #define AD7192_STAT_PARITY BIT(4) /* Parity */ 54 #define AD7192_STAT_CH3 BIT(2) /* Channel 3 */ 55 #define AD7192_STAT_CH2 BIT(1) /* Channel 2 */ 56 #define AD7192_STAT_CH1 BIT(0) /* Channel 1 */ 57 58 /* Mode Register Bit Designations (AD7192_REG_MODE) */ 59 #define AD7192_MODE_SEL(x) (((x) & 0x7) << 21) /* Operation Mode Select */ 60 #define AD7192_MODE_SEL_MASK (0x7 << 21) /* Operation Mode Select Mask */ 61 #define AD7192_MODE_STA(x) (((x) & 0x1) << 20) /* Status Register transmission */ 62 #define AD7192_MODE_STA_MASK BIT(20) /* Status Register transmission Mask */ 63 #define AD7192_MODE_CLKSRC(x) (((x) & 0x3) << 18) /* Clock Source Select */ 64 #define AD7192_MODE_SINC3 BIT(15) /* SINC3 Filter Select */ 65 #define AD7192_MODE_ENPAR BIT(13) /* Parity Enable */ 66 #define AD7192_MODE_CLKDIV BIT(12) /* Clock divide by 2 (AD7190/2 only)*/ 67 #define AD7192_MODE_SCYCLE BIT(11) /* Single cycle conversion */ 68 #define AD7192_MODE_REJ60 BIT(10) /* 50/60Hz notch filter */ 69 #define AD7192_MODE_RATE(x) ((x) & 0x3FF) /* Filter Update Rate Select */ 70 71 /* Mode Register: AD7192_MODE_SEL options */ 72 #define AD7192_MODE_CONT 0 /* Continuous Conversion Mode */ 73 #define AD7192_MODE_SINGLE 1 /* Single Conversion Mode */ 74 #define AD7192_MODE_IDLE 2 /* Idle Mode */ 75 #define AD7192_MODE_PWRDN 3 /* Power-Down Mode */ 76 #define AD7192_MODE_CAL_INT_ZERO 4 /* Internal Zero-Scale Calibration */ 77 #define AD7192_MODE_CAL_INT_FULL 5 /* Internal Full-Scale Calibration */ 78 #define AD7192_MODE_CAL_SYS_ZERO 6 /* System Zero-Scale Calibration */ 79 #define AD7192_MODE_CAL_SYS_FULL 7 /* System Full-Scale Calibration */ 80 81 /* Mode Register: AD7192_MODE_CLKSRC options */ 82 #define AD7192_CLK_EXT_MCLK1_2 0 /* External 4.92 MHz Clock connected*/ 83 /* from MCLK1 to MCLK2 */ 84 #define AD7192_CLK_EXT_MCLK2 1 /* External Clock applied to MCLK2 */ 85 #define AD7192_CLK_INT 2 /* Internal 4.92 MHz Clock not */ 86 /* available at the MCLK2 pin */ 87 #define AD7192_CLK_INT_CO 3 /* Internal 4.92 MHz Clock available*/ 88 /* at the MCLK2 pin */ 89 90 /* Configuration Register Bit Designations (AD7192_REG_CONF) */ 91 92 #define AD7192_CONF_CHOP BIT(23) /* CHOP enable */ 93 #define AD7192_CONF_ACX BIT(22) /* AC excitation enable(AD7195 only) */ 94 #define AD7192_CONF_REFSEL BIT(20) /* REFIN1/REFIN2 Reference Select */ 95 #define AD7192_CONF_CHAN(x) ((x) << 8) /* Channel select */ 96 #define AD7192_CONF_CHAN_MASK (0x7FF << 8) /* Channel select mask */ 97 #define AD7192_CONF_BURN BIT(7) /* Burnout current enable */ 98 #define AD7192_CONF_REFDET BIT(6) /* Reference detect enable */ 99 #define AD7192_CONF_BUF BIT(4) /* Buffered Mode Enable */ 100 #define AD7192_CONF_UNIPOLAR BIT(3) /* Unipolar/Bipolar Enable */ 101 #define AD7192_CONF_GAIN(x) ((x) & 0x7) /* Gain Select */ 102 103 #define AD7192_CH_AIN1P_AIN2M BIT(0) /* AIN1(+) - AIN2(-) */ 104 #define AD7192_CH_AIN3P_AIN4M BIT(1) /* AIN3(+) - AIN4(-) */ 105 #define AD7192_CH_TEMP BIT(2) /* Temp Sensor */ 106 #define AD7192_CH_AIN2P_AIN2M BIT(3) /* AIN2(+) - AIN2(-) */ 107 #define AD7192_CH_AIN1 BIT(4) /* AIN1 - AINCOM */ 108 #define AD7192_CH_AIN2 BIT(5) /* AIN2 - AINCOM */ 109 #define AD7192_CH_AIN3 BIT(6) /* AIN3 - AINCOM */ 110 #define AD7192_CH_AIN4 BIT(7) /* AIN4 - AINCOM */ 111 112 #define AD7193_CH_AIN1P_AIN2M 0x001 /* AIN1(+) - AIN2(-) */ 113 #define AD7193_CH_AIN3P_AIN4M 0x002 /* AIN3(+) - AIN4(-) */ 114 #define AD7193_CH_AIN5P_AIN6M 0x004 /* AIN5(+) - AIN6(-) */ 115 #define AD7193_CH_AIN7P_AIN8M 0x008 /* AIN7(+) - AIN8(-) */ 116 #define AD7193_CH_TEMP 0x100 /* Temp senseor */ 117 #define AD7193_CH_AIN2P_AIN2M 0x200 /* AIN2(+) - AIN2(-) */ 118 #define AD7193_CH_AIN1 0x401 /* AIN1 - AINCOM */ 119 #define AD7193_CH_AIN2 0x402 /* AIN2 - AINCOM */ 120 #define AD7193_CH_AIN3 0x404 /* AIN3 - AINCOM */ 121 #define AD7193_CH_AIN4 0x408 /* AIN4 - AINCOM */ 122 #define AD7193_CH_AIN5 0x410 /* AIN5 - AINCOM */ 123 #define AD7193_CH_AIN6 0x420 /* AIN6 - AINCOM */ 124 #define AD7193_CH_AIN7 0x440 /* AIN7 - AINCOM */ 125 #define AD7193_CH_AIN8 0x480 /* AIN7 - AINCOM */ 126 #define AD7193_CH_AINCOM 0x600 /* AINCOM - AINCOM */ 127 128 /* ID Register Bit Designations (AD7192_REG_ID) */ 129 #define CHIPID_AD7190 0x4 130 #define CHIPID_AD7192 0x0 131 #define CHIPID_AD7193 0x2 132 #define CHIPID_AD7195 0x6 133 #define AD7192_ID_MASK 0x0F 134 135 /* GPOCON Register Bit Designations (AD7192_REG_GPOCON) */ 136 #define AD7192_GPOCON_BPDSW BIT(6) /* Bridge power-down switch enable */ 137 #define AD7192_GPOCON_GP32EN BIT(5) /* Digital Output P3 and P2 enable */ 138 #define AD7192_GPOCON_GP10EN BIT(4) /* Digital Output P1 and P0 enable */ 139 #define AD7192_GPOCON_P3DAT BIT(3) /* P3 state */ 140 #define AD7192_GPOCON_P2DAT BIT(2) /* P2 state */ 141 #define AD7192_GPOCON_P1DAT BIT(1) /* P1 state */ 142 #define AD7192_GPOCON_P0DAT BIT(0) /* P0 state */ 143 144 #define AD7192_EXT_FREQ_MHZ_MIN 2457600 145 #define AD7192_EXT_FREQ_MHZ_MAX 5120000 146 #define AD7192_INT_FREQ_MHZ 4915200 147 148 #define AD7192_NO_SYNC_FILTER 1 149 #define AD7192_SYNC3_FILTER 3 150 #define AD7192_SYNC4_FILTER 4 151 152 /* NOTE: 153 * The AD7190/2/5 features a dual use data out ready DOUT/RDY output. 154 * In order to avoid contentions on the SPI bus, it's therefore necessary 155 * to use spi bus locking. 156 * 157 * The DOUT/RDY output must also be wired to an interrupt capable GPIO. 158 */ 159 160 enum { 161 AD7192_SYSCALIB_ZERO_SCALE, 162 AD7192_SYSCALIB_FULL_SCALE, 163 }; 164 165 enum { 166 ID_AD7190, 167 ID_AD7192, 168 ID_AD7193, 169 ID_AD7195, 170 }; 171 172 struct ad7192_chip_info { 173 unsigned int chip_id; 174 const char *name; 175 }; 176 177 struct ad7192_state { 178 const struct ad7192_chip_info *chip_info; 179 struct regulator *avdd; 180 struct regulator *vref; 181 struct clk *mclk; 182 u16 int_vref_mv; 183 u32 fclk; 184 u32 f_order; 185 u32 mode; 186 u32 conf; 187 u32 scale_avail[8][2]; 188 u8 gpocon; 189 u8 clock_sel; 190 struct mutex lock; /* protect sensor state */ 191 u8 syscalib_mode[8]; 192 193 struct ad_sigma_delta sd; 194 }; 195 196 static const char * const ad7192_syscalib_modes[] = { 197 [AD7192_SYSCALIB_ZERO_SCALE] = "zero_scale", 198 [AD7192_SYSCALIB_FULL_SCALE] = "full_scale", 199 }; 200 201 static int ad7192_set_syscalib_mode(struct iio_dev *indio_dev, 202 const struct iio_chan_spec *chan, 203 unsigned int mode) 204 { 205 struct ad7192_state *st = iio_priv(indio_dev); 206 207 st->syscalib_mode[chan->channel] = mode; 208 209 return 0; 210 } 211 212 static int ad7192_get_syscalib_mode(struct iio_dev *indio_dev, 213 const struct iio_chan_spec *chan) 214 { 215 struct ad7192_state *st = iio_priv(indio_dev); 216 217 return st->syscalib_mode[chan->channel]; 218 } 219 220 static ssize_t ad7192_write_syscalib(struct iio_dev *indio_dev, 221 uintptr_t private, 222 const struct iio_chan_spec *chan, 223 const char *buf, size_t len) 224 { 225 struct ad7192_state *st = iio_priv(indio_dev); 226 bool sys_calib; 227 int ret, temp; 228 229 ret = kstrtobool(buf, &sys_calib); 230 if (ret) 231 return ret; 232 233 temp = st->syscalib_mode[chan->channel]; 234 if (sys_calib) { 235 if (temp == AD7192_SYSCALIB_ZERO_SCALE) 236 ret = ad_sd_calibrate(&st->sd, AD7192_MODE_CAL_SYS_ZERO, 237 chan->address); 238 else 239 ret = ad_sd_calibrate(&st->sd, AD7192_MODE_CAL_SYS_FULL, 240 chan->address); 241 } 242 243 return ret ? ret : len; 244 } 245 246 static const struct iio_enum ad7192_syscalib_mode_enum = { 247 .items = ad7192_syscalib_modes, 248 .num_items = ARRAY_SIZE(ad7192_syscalib_modes), 249 .set = ad7192_set_syscalib_mode, 250 .get = ad7192_get_syscalib_mode 251 }; 252 253 static const struct iio_chan_spec_ext_info ad7192_calibsys_ext_info[] = { 254 { 255 .name = "sys_calibration", 256 .write = ad7192_write_syscalib, 257 .shared = IIO_SEPARATE, 258 }, 259 IIO_ENUM("sys_calibration_mode", IIO_SEPARATE, 260 &ad7192_syscalib_mode_enum), 261 IIO_ENUM_AVAILABLE("sys_calibration_mode", IIO_SHARED_BY_TYPE, 262 &ad7192_syscalib_mode_enum), 263 {} 264 }; 265 266 static struct ad7192_state *ad_sigma_delta_to_ad7192(struct ad_sigma_delta *sd) 267 { 268 return container_of(sd, struct ad7192_state, sd); 269 } 270 271 static int ad7192_set_channel(struct ad_sigma_delta *sd, unsigned int channel) 272 { 273 struct ad7192_state *st = ad_sigma_delta_to_ad7192(sd); 274 275 st->conf &= ~AD7192_CONF_CHAN_MASK; 276 st->conf |= AD7192_CONF_CHAN(channel); 277 278 return ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, st->conf); 279 } 280 281 static int ad7192_set_mode(struct ad_sigma_delta *sd, 282 enum ad_sigma_delta_mode mode) 283 { 284 struct ad7192_state *st = ad_sigma_delta_to_ad7192(sd); 285 286 st->mode &= ~AD7192_MODE_SEL_MASK; 287 st->mode |= AD7192_MODE_SEL(mode); 288 289 return ad_sd_write_reg(&st->sd, AD7192_REG_MODE, 3, st->mode); 290 } 291 292 static int ad7192_append_status(struct ad_sigma_delta *sd, bool append) 293 { 294 struct ad7192_state *st = ad_sigma_delta_to_ad7192(sd); 295 unsigned int mode = st->mode; 296 int ret; 297 298 mode &= ~AD7192_MODE_STA_MASK; 299 mode |= AD7192_MODE_STA(append); 300 301 ret = ad_sd_write_reg(&st->sd, AD7192_REG_MODE, 3, mode); 302 if (ret < 0) 303 return ret; 304 305 st->mode = mode; 306 307 return 0; 308 } 309 310 static int ad7192_disable_all(struct ad_sigma_delta *sd) 311 { 312 struct ad7192_state *st = ad_sigma_delta_to_ad7192(sd); 313 u32 conf = st->conf; 314 int ret; 315 316 conf &= ~AD7192_CONF_CHAN_MASK; 317 318 ret = ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, conf); 319 if (ret < 0) 320 return ret; 321 322 st->conf = conf; 323 324 return 0; 325 } 326 327 static const struct ad_sigma_delta_info ad7192_sigma_delta_info = { 328 .set_channel = ad7192_set_channel, 329 .append_status = ad7192_append_status, 330 .disable_all = ad7192_disable_all, 331 .set_mode = ad7192_set_mode, 332 .has_registers = true, 333 .addr_shift = 3, 334 .read_mask = BIT(6), 335 .status_ch_mask = GENMASK(3, 0), 336 .num_slots = 4, 337 .irq_flags = IRQF_TRIGGER_FALLING, 338 }; 339 340 static const struct ad_sd_calib_data ad7192_calib_arr[8] = { 341 {AD7192_MODE_CAL_INT_ZERO, AD7192_CH_AIN1}, 342 {AD7192_MODE_CAL_INT_FULL, AD7192_CH_AIN1}, 343 {AD7192_MODE_CAL_INT_ZERO, AD7192_CH_AIN2}, 344 {AD7192_MODE_CAL_INT_FULL, AD7192_CH_AIN2}, 345 {AD7192_MODE_CAL_INT_ZERO, AD7192_CH_AIN3}, 346 {AD7192_MODE_CAL_INT_FULL, AD7192_CH_AIN3}, 347 {AD7192_MODE_CAL_INT_ZERO, AD7192_CH_AIN4}, 348 {AD7192_MODE_CAL_INT_FULL, AD7192_CH_AIN4} 349 }; 350 351 static int ad7192_calibrate_all(struct ad7192_state *st) 352 { 353 return ad_sd_calibrate_all(&st->sd, ad7192_calib_arr, 354 ARRAY_SIZE(ad7192_calib_arr)); 355 } 356 357 static inline bool ad7192_valid_external_frequency(u32 freq) 358 { 359 return (freq >= AD7192_EXT_FREQ_MHZ_MIN && 360 freq <= AD7192_EXT_FREQ_MHZ_MAX); 361 } 362 363 static int ad7192_of_clock_select(struct ad7192_state *st) 364 { 365 struct device_node *np = st->sd.spi->dev.of_node; 366 unsigned int clock_sel; 367 368 clock_sel = AD7192_CLK_INT; 369 370 /* use internal clock */ 371 if (!st->mclk) { 372 if (of_property_read_bool(np, "adi,int-clock-output-enable")) 373 clock_sel = AD7192_CLK_INT_CO; 374 } else { 375 if (of_property_read_bool(np, "adi,clock-xtal")) 376 clock_sel = AD7192_CLK_EXT_MCLK1_2; 377 else 378 clock_sel = AD7192_CLK_EXT_MCLK2; 379 } 380 381 return clock_sel; 382 } 383 384 static int ad7192_setup(struct iio_dev *indio_dev, struct device_node *np) 385 { 386 struct ad7192_state *st = iio_priv(indio_dev); 387 bool rej60_en, refin2_en; 388 bool buf_en, bipolar, burnout_curr_en; 389 unsigned long long scale_uv; 390 int i, ret, id; 391 392 /* reset the serial interface */ 393 ret = ad_sd_reset(&st->sd, 48); 394 if (ret < 0) 395 return ret; 396 usleep_range(500, 1000); /* Wait for at least 500us */ 397 398 /* write/read test for device presence */ 399 ret = ad_sd_read_reg(&st->sd, AD7192_REG_ID, 1, &id); 400 if (ret) 401 return ret; 402 403 id &= AD7192_ID_MASK; 404 405 if (id != st->chip_info->chip_id) 406 dev_warn(&st->sd.spi->dev, "device ID query failed (0x%X != 0x%X)\n", 407 id, st->chip_info->chip_id); 408 409 st->mode = AD7192_MODE_SEL(AD7192_MODE_IDLE) | 410 AD7192_MODE_CLKSRC(st->clock_sel) | 411 AD7192_MODE_RATE(480); 412 413 st->conf = AD7192_CONF_GAIN(0); 414 415 rej60_en = of_property_read_bool(np, "adi,rejection-60-Hz-enable"); 416 if (rej60_en) 417 st->mode |= AD7192_MODE_REJ60; 418 419 refin2_en = of_property_read_bool(np, "adi,refin2-pins-enable"); 420 if (refin2_en && st->chip_info->chip_id != CHIPID_AD7195) 421 st->conf |= AD7192_CONF_REFSEL; 422 423 st->conf &= ~AD7192_CONF_CHOP; 424 st->f_order = AD7192_NO_SYNC_FILTER; 425 426 buf_en = of_property_read_bool(np, "adi,buffer-enable"); 427 if (buf_en) 428 st->conf |= AD7192_CONF_BUF; 429 430 bipolar = of_property_read_bool(np, "bipolar"); 431 if (!bipolar) 432 st->conf |= AD7192_CONF_UNIPOLAR; 433 434 burnout_curr_en = of_property_read_bool(np, 435 "adi,burnout-currents-enable"); 436 if (burnout_curr_en && buf_en) { 437 st->conf |= AD7192_CONF_BURN; 438 } else if (burnout_curr_en) { 439 dev_warn(&st->sd.spi->dev, 440 "Can't enable burnout currents: see CHOP or buffer\n"); 441 } 442 443 ret = ad_sd_write_reg(&st->sd, AD7192_REG_MODE, 3, st->mode); 444 if (ret) 445 return ret; 446 447 ret = ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, st->conf); 448 if (ret) 449 return ret; 450 451 ret = ad7192_calibrate_all(st); 452 if (ret) 453 return ret; 454 455 /* Populate available ADC input ranges */ 456 for (i = 0; i < ARRAY_SIZE(st->scale_avail); i++) { 457 scale_uv = ((u64)st->int_vref_mv * 100000000) 458 >> (indio_dev->channels[0].scan_type.realbits - 459 ((st->conf & AD7192_CONF_UNIPOLAR) ? 0 : 1)); 460 scale_uv >>= i; 461 462 st->scale_avail[i][1] = do_div(scale_uv, 100000000) * 10; 463 st->scale_avail[i][0] = scale_uv; 464 } 465 466 return 0; 467 } 468 469 static ssize_t ad7192_show_ac_excitation(struct device *dev, 470 struct device_attribute *attr, 471 char *buf) 472 { 473 struct iio_dev *indio_dev = dev_to_iio_dev(dev); 474 struct ad7192_state *st = iio_priv(indio_dev); 475 476 return sysfs_emit(buf, "%d\n", !!(st->conf & AD7192_CONF_ACX)); 477 } 478 479 static ssize_t ad7192_show_bridge_switch(struct device *dev, 480 struct device_attribute *attr, 481 char *buf) 482 { 483 struct iio_dev *indio_dev = dev_to_iio_dev(dev); 484 struct ad7192_state *st = iio_priv(indio_dev); 485 486 return sysfs_emit(buf, "%d\n", !!(st->gpocon & AD7192_GPOCON_BPDSW)); 487 } 488 489 static ssize_t ad7192_set(struct device *dev, 490 struct device_attribute *attr, 491 const char *buf, 492 size_t len) 493 { 494 struct iio_dev *indio_dev = dev_to_iio_dev(dev); 495 struct ad7192_state *st = iio_priv(indio_dev); 496 struct iio_dev_attr *this_attr = to_iio_dev_attr(attr); 497 int ret; 498 bool val; 499 500 ret = kstrtobool(buf, &val); 501 if (ret < 0) 502 return ret; 503 504 ret = iio_device_claim_direct_mode(indio_dev); 505 if (ret) 506 return ret; 507 508 switch ((u32)this_attr->address) { 509 case AD7192_REG_GPOCON: 510 if (val) 511 st->gpocon |= AD7192_GPOCON_BPDSW; 512 else 513 st->gpocon &= ~AD7192_GPOCON_BPDSW; 514 515 ad_sd_write_reg(&st->sd, AD7192_REG_GPOCON, 1, st->gpocon); 516 break; 517 case AD7192_REG_CONF: 518 if (val) 519 st->conf |= AD7192_CONF_ACX; 520 else 521 st->conf &= ~AD7192_CONF_ACX; 522 523 ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, st->conf); 524 break; 525 default: 526 ret = -EINVAL; 527 } 528 529 iio_device_release_direct_mode(indio_dev); 530 531 return ret ? ret : len; 532 } 533 534 static void ad7192_get_available_filter_freq(struct ad7192_state *st, 535 int *freq) 536 { 537 unsigned int fadc; 538 539 /* Formulas for filter at page 25 of the datasheet */ 540 fadc = DIV_ROUND_CLOSEST(st->fclk, 541 AD7192_SYNC4_FILTER * AD7192_MODE_RATE(st->mode)); 542 freq[0] = DIV_ROUND_CLOSEST(fadc * 240, 1024); 543 544 fadc = DIV_ROUND_CLOSEST(st->fclk, 545 AD7192_SYNC3_FILTER * AD7192_MODE_RATE(st->mode)); 546 freq[1] = DIV_ROUND_CLOSEST(fadc * 240, 1024); 547 548 fadc = DIV_ROUND_CLOSEST(st->fclk, AD7192_MODE_RATE(st->mode)); 549 freq[2] = DIV_ROUND_CLOSEST(fadc * 230, 1024); 550 freq[3] = DIV_ROUND_CLOSEST(fadc * 272, 1024); 551 } 552 553 static ssize_t ad7192_show_filter_avail(struct device *dev, 554 struct device_attribute *attr, 555 char *buf) 556 { 557 struct iio_dev *indio_dev = dev_to_iio_dev(dev); 558 struct ad7192_state *st = iio_priv(indio_dev); 559 unsigned int freq_avail[4], i; 560 size_t len = 0; 561 562 ad7192_get_available_filter_freq(st, freq_avail); 563 564 for (i = 0; i < ARRAY_SIZE(freq_avail); i++) 565 len += sysfs_emit_at(buf, len, "%d.%03d ", freq_avail[i] / 1000, 566 freq_avail[i] % 1000); 567 568 buf[len - 1] = '\n'; 569 570 return len; 571 } 572 573 static IIO_DEVICE_ATTR(filter_low_pass_3db_frequency_available, 574 0444, ad7192_show_filter_avail, NULL, 0); 575 576 static IIO_DEVICE_ATTR(bridge_switch_en, 0644, 577 ad7192_show_bridge_switch, ad7192_set, 578 AD7192_REG_GPOCON); 579 580 static IIO_DEVICE_ATTR(ac_excitation_en, 0644, 581 ad7192_show_ac_excitation, ad7192_set, 582 AD7192_REG_CONF); 583 584 static struct attribute *ad7192_attributes[] = { 585 &iio_dev_attr_filter_low_pass_3db_frequency_available.dev_attr.attr, 586 &iio_dev_attr_bridge_switch_en.dev_attr.attr, 587 NULL 588 }; 589 590 static const struct attribute_group ad7192_attribute_group = { 591 .attrs = ad7192_attributes, 592 }; 593 594 static struct attribute *ad7195_attributes[] = { 595 &iio_dev_attr_filter_low_pass_3db_frequency_available.dev_attr.attr, 596 &iio_dev_attr_bridge_switch_en.dev_attr.attr, 597 &iio_dev_attr_ac_excitation_en.dev_attr.attr, 598 NULL 599 }; 600 601 static const struct attribute_group ad7195_attribute_group = { 602 .attrs = ad7195_attributes, 603 }; 604 605 static unsigned int ad7192_get_temp_scale(bool unipolar) 606 { 607 return unipolar ? 2815 * 2 : 2815; 608 } 609 610 static int ad7192_set_3db_filter_freq(struct ad7192_state *st, 611 int val, int val2) 612 { 613 int freq_avail[4], i, ret, freq; 614 unsigned int diff_new, diff_old; 615 int idx = 0; 616 617 diff_old = U32_MAX; 618 freq = val * 1000 + val2; 619 620 ad7192_get_available_filter_freq(st, freq_avail); 621 622 for (i = 0; i < ARRAY_SIZE(freq_avail); i++) { 623 diff_new = abs(freq - freq_avail[i]); 624 if (diff_new < diff_old) { 625 diff_old = diff_new; 626 idx = i; 627 } 628 } 629 630 switch (idx) { 631 case 0: 632 st->f_order = AD7192_SYNC4_FILTER; 633 st->mode &= ~AD7192_MODE_SINC3; 634 635 st->conf |= AD7192_CONF_CHOP; 636 break; 637 case 1: 638 st->f_order = AD7192_SYNC3_FILTER; 639 st->mode |= AD7192_MODE_SINC3; 640 641 st->conf |= AD7192_CONF_CHOP; 642 break; 643 case 2: 644 st->f_order = AD7192_NO_SYNC_FILTER; 645 st->mode &= ~AD7192_MODE_SINC3; 646 647 st->conf &= ~AD7192_CONF_CHOP; 648 break; 649 case 3: 650 st->f_order = AD7192_NO_SYNC_FILTER; 651 st->mode |= AD7192_MODE_SINC3; 652 653 st->conf &= ~AD7192_CONF_CHOP; 654 break; 655 } 656 657 ret = ad_sd_write_reg(&st->sd, AD7192_REG_MODE, 3, st->mode); 658 if (ret < 0) 659 return ret; 660 661 return ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, st->conf); 662 } 663 664 static int ad7192_get_3db_filter_freq(struct ad7192_state *st) 665 { 666 unsigned int fadc; 667 668 fadc = DIV_ROUND_CLOSEST(st->fclk, 669 st->f_order * AD7192_MODE_RATE(st->mode)); 670 671 if (st->conf & AD7192_CONF_CHOP) 672 return DIV_ROUND_CLOSEST(fadc * 240, 1024); 673 if (st->mode & AD7192_MODE_SINC3) 674 return DIV_ROUND_CLOSEST(fadc * 272, 1024); 675 else 676 return DIV_ROUND_CLOSEST(fadc * 230, 1024); 677 } 678 679 static int ad7192_read_raw(struct iio_dev *indio_dev, 680 struct iio_chan_spec const *chan, 681 int *val, 682 int *val2, 683 long m) 684 { 685 struct ad7192_state *st = iio_priv(indio_dev); 686 bool unipolar = !!(st->conf & AD7192_CONF_UNIPOLAR); 687 688 switch (m) { 689 case IIO_CHAN_INFO_RAW: 690 return ad_sigma_delta_single_conversion(indio_dev, chan, val); 691 case IIO_CHAN_INFO_SCALE: 692 switch (chan->type) { 693 case IIO_VOLTAGE: 694 mutex_lock(&st->lock); 695 *val = st->scale_avail[AD7192_CONF_GAIN(st->conf)][0]; 696 *val2 = st->scale_avail[AD7192_CONF_GAIN(st->conf)][1]; 697 mutex_unlock(&st->lock); 698 return IIO_VAL_INT_PLUS_NANO; 699 case IIO_TEMP: 700 *val = 0; 701 *val2 = 1000000000 / ad7192_get_temp_scale(unipolar); 702 return IIO_VAL_INT_PLUS_NANO; 703 default: 704 return -EINVAL; 705 } 706 case IIO_CHAN_INFO_OFFSET: 707 if (!unipolar) 708 *val = -(1 << (chan->scan_type.realbits - 1)); 709 else 710 *val = 0; 711 /* Kelvin to Celsius */ 712 if (chan->type == IIO_TEMP) 713 *val -= 273 * ad7192_get_temp_scale(unipolar); 714 return IIO_VAL_INT; 715 case IIO_CHAN_INFO_SAMP_FREQ: 716 *val = st->fclk / 717 (st->f_order * 1024 * AD7192_MODE_RATE(st->mode)); 718 return IIO_VAL_INT; 719 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 720 *val = ad7192_get_3db_filter_freq(st); 721 *val2 = 1000; 722 return IIO_VAL_FRACTIONAL; 723 } 724 725 return -EINVAL; 726 } 727 728 static int ad7192_write_raw(struct iio_dev *indio_dev, 729 struct iio_chan_spec const *chan, 730 int val, 731 int val2, 732 long mask) 733 { 734 struct ad7192_state *st = iio_priv(indio_dev); 735 int ret, i, div; 736 unsigned int tmp; 737 738 ret = iio_device_claim_direct_mode(indio_dev); 739 if (ret) 740 return ret; 741 742 switch (mask) { 743 case IIO_CHAN_INFO_SCALE: 744 ret = -EINVAL; 745 mutex_lock(&st->lock); 746 for (i = 0; i < ARRAY_SIZE(st->scale_avail); i++) 747 if (val2 == st->scale_avail[i][1]) { 748 ret = 0; 749 tmp = st->conf; 750 st->conf &= ~AD7192_CONF_GAIN(-1); 751 st->conf |= AD7192_CONF_GAIN(i); 752 if (tmp == st->conf) 753 break; 754 ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 755 3, st->conf); 756 ad7192_calibrate_all(st); 757 break; 758 } 759 mutex_unlock(&st->lock); 760 break; 761 case IIO_CHAN_INFO_SAMP_FREQ: 762 if (!val) { 763 ret = -EINVAL; 764 break; 765 } 766 767 div = st->fclk / (val * st->f_order * 1024); 768 if (div < 1 || div > 1023) { 769 ret = -EINVAL; 770 break; 771 } 772 773 st->mode &= ~AD7192_MODE_RATE(-1); 774 st->mode |= AD7192_MODE_RATE(div); 775 ad_sd_write_reg(&st->sd, AD7192_REG_MODE, 3, st->mode); 776 break; 777 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 778 ret = ad7192_set_3db_filter_freq(st, val, val2 / 1000); 779 break; 780 default: 781 ret = -EINVAL; 782 } 783 784 iio_device_release_direct_mode(indio_dev); 785 786 return ret; 787 } 788 789 static int ad7192_write_raw_get_fmt(struct iio_dev *indio_dev, 790 struct iio_chan_spec const *chan, 791 long mask) 792 { 793 switch (mask) { 794 case IIO_CHAN_INFO_SCALE: 795 return IIO_VAL_INT_PLUS_NANO; 796 case IIO_CHAN_INFO_SAMP_FREQ: 797 return IIO_VAL_INT; 798 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 799 return IIO_VAL_INT_PLUS_MICRO; 800 default: 801 return -EINVAL; 802 } 803 } 804 805 static int ad7192_read_avail(struct iio_dev *indio_dev, 806 struct iio_chan_spec const *chan, 807 const int **vals, int *type, int *length, 808 long mask) 809 { 810 struct ad7192_state *st = iio_priv(indio_dev); 811 812 switch (mask) { 813 case IIO_CHAN_INFO_SCALE: 814 *vals = (int *)st->scale_avail; 815 *type = IIO_VAL_INT_PLUS_NANO; 816 /* Values are stored in a 2D matrix */ 817 *length = ARRAY_SIZE(st->scale_avail) * 2; 818 819 return IIO_AVAIL_LIST; 820 } 821 822 return -EINVAL; 823 } 824 825 static int ad7192_update_scan_mode(struct iio_dev *indio_dev, const unsigned long *scan_mask) 826 { 827 struct ad7192_state *st = iio_priv(indio_dev); 828 u32 conf = st->conf; 829 int ret; 830 int i; 831 832 conf &= ~AD7192_CONF_CHAN_MASK; 833 for_each_set_bit(i, scan_mask, 8) 834 conf |= AD7192_CONF_CHAN(i); 835 836 ret = ad_sd_write_reg(&st->sd, AD7192_REG_CONF, 3, conf); 837 if (ret < 0) 838 return ret; 839 840 st->conf = conf; 841 842 return 0; 843 } 844 845 static const struct iio_info ad7192_info = { 846 .read_raw = ad7192_read_raw, 847 .write_raw = ad7192_write_raw, 848 .write_raw_get_fmt = ad7192_write_raw_get_fmt, 849 .read_avail = ad7192_read_avail, 850 .attrs = &ad7192_attribute_group, 851 .validate_trigger = ad_sd_validate_trigger, 852 .update_scan_mode = ad7192_update_scan_mode, 853 }; 854 855 static const struct iio_info ad7195_info = { 856 .read_raw = ad7192_read_raw, 857 .write_raw = ad7192_write_raw, 858 .write_raw_get_fmt = ad7192_write_raw_get_fmt, 859 .read_avail = ad7192_read_avail, 860 .attrs = &ad7195_attribute_group, 861 .validate_trigger = ad_sd_validate_trigger, 862 .update_scan_mode = ad7192_update_scan_mode, 863 }; 864 865 #define __AD719x_CHANNEL(_si, _channel1, _channel2, _address, _extend_name, \ 866 _type, _mask_type_av, _ext_info) \ 867 { \ 868 .type = (_type), \ 869 .differential = ((_channel2) == -1 ? 0 : 1), \ 870 .indexed = 1, \ 871 .channel = (_channel1), \ 872 .channel2 = (_channel2), \ 873 .address = (_address), \ 874 .extend_name = (_extend_name), \ 875 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ 876 BIT(IIO_CHAN_INFO_OFFSET), \ 877 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ 878 .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \ 879 BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), \ 880 .info_mask_shared_by_type_available = (_mask_type_av), \ 881 .ext_info = (_ext_info), \ 882 .scan_index = (_si), \ 883 .scan_type = { \ 884 .sign = 'u', \ 885 .realbits = 24, \ 886 .storagebits = 32, \ 887 .endianness = IIO_BE, \ 888 }, \ 889 } 890 891 #define AD719x_DIFF_CHANNEL(_si, _channel1, _channel2, _address) \ 892 __AD719x_CHANNEL(_si, _channel1, _channel2, _address, NULL, \ 893 IIO_VOLTAGE, BIT(IIO_CHAN_INFO_SCALE), \ 894 ad7192_calibsys_ext_info) 895 896 #define AD719x_CHANNEL(_si, _channel1, _address) \ 897 __AD719x_CHANNEL(_si, _channel1, -1, _address, NULL, IIO_VOLTAGE, \ 898 BIT(IIO_CHAN_INFO_SCALE), ad7192_calibsys_ext_info) 899 900 #define AD719x_TEMP_CHANNEL(_si, _address) \ 901 __AD719x_CHANNEL(_si, 0, -1, _address, NULL, IIO_TEMP, 0, NULL) 902 903 static const struct iio_chan_spec ad7192_channels[] = { 904 AD719x_DIFF_CHANNEL(0, 1, 2, AD7192_CH_AIN1P_AIN2M), 905 AD719x_DIFF_CHANNEL(1, 3, 4, AD7192_CH_AIN3P_AIN4M), 906 AD719x_TEMP_CHANNEL(2, AD7192_CH_TEMP), 907 AD719x_DIFF_CHANNEL(3, 2, 2, AD7192_CH_AIN2P_AIN2M), 908 AD719x_CHANNEL(4, 1, AD7192_CH_AIN1), 909 AD719x_CHANNEL(5, 2, AD7192_CH_AIN2), 910 AD719x_CHANNEL(6, 3, AD7192_CH_AIN3), 911 AD719x_CHANNEL(7, 4, AD7192_CH_AIN4), 912 IIO_CHAN_SOFT_TIMESTAMP(8), 913 }; 914 915 static const struct iio_chan_spec ad7193_channels[] = { 916 AD719x_DIFF_CHANNEL(0, 1, 2, AD7193_CH_AIN1P_AIN2M), 917 AD719x_DIFF_CHANNEL(1, 3, 4, AD7193_CH_AIN3P_AIN4M), 918 AD719x_DIFF_CHANNEL(2, 5, 6, AD7193_CH_AIN5P_AIN6M), 919 AD719x_DIFF_CHANNEL(3, 7, 8, AD7193_CH_AIN7P_AIN8M), 920 AD719x_TEMP_CHANNEL(4, AD7193_CH_TEMP), 921 AD719x_DIFF_CHANNEL(5, 2, 2, AD7193_CH_AIN2P_AIN2M), 922 AD719x_CHANNEL(6, 1, AD7193_CH_AIN1), 923 AD719x_CHANNEL(7, 2, AD7193_CH_AIN2), 924 AD719x_CHANNEL(8, 3, AD7193_CH_AIN3), 925 AD719x_CHANNEL(9, 4, AD7193_CH_AIN4), 926 AD719x_CHANNEL(10, 5, AD7193_CH_AIN5), 927 AD719x_CHANNEL(11, 6, AD7193_CH_AIN6), 928 AD719x_CHANNEL(12, 7, AD7193_CH_AIN7), 929 AD719x_CHANNEL(13, 8, AD7193_CH_AIN8), 930 IIO_CHAN_SOFT_TIMESTAMP(14), 931 }; 932 933 static const struct ad7192_chip_info ad7192_chip_info_tbl[] = { 934 [ID_AD7190] = { 935 .chip_id = CHIPID_AD7190, 936 .name = "ad7190", 937 }, 938 [ID_AD7192] = { 939 .chip_id = CHIPID_AD7192, 940 .name = "ad7192", 941 }, 942 [ID_AD7193] = { 943 .chip_id = CHIPID_AD7193, 944 .name = "ad7193", 945 }, 946 [ID_AD7195] = { 947 .chip_id = CHIPID_AD7195, 948 .name = "ad7195", 949 }, 950 }; 951 952 static int ad7192_channels_config(struct iio_dev *indio_dev) 953 { 954 struct ad7192_state *st = iio_priv(indio_dev); 955 956 switch (st->chip_info->chip_id) { 957 case CHIPID_AD7193: 958 indio_dev->channels = ad7193_channels; 959 indio_dev->num_channels = ARRAY_SIZE(ad7193_channels); 960 break; 961 default: 962 indio_dev->channels = ad7192_channels; 963 indio_dev->num_channels = ARRAY_SIZE(ad7192_channels); 964 break; 965 } 966 967 return 0; 968 } 969 970 static void ad7192_reg_disable(void *reg) 971 { 972 regulator_disable(reg); 973 } 974 975 static int ad7192_probe(struct spi_device *spi) 976 { 977 struct ad7192_state *st; 978 struct iio_dev *indio_dev; 979 int ret; 980 981 if (!spi->irq) { 982 dev_err(&spi->dev, "no IRQ?\n"); 983 return -ENODEV; 984 } 985 986 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); 987 if (!indio_dev) 988 return -ENOMEM; 989 990 st = iio_priv(indio_dev); 991 992 mutex_init(&st->lock); 993 994 st->avdd = devm_regulator_get(&spi->dev, "avdd"); 995 if (IS_ERR(st->avdd)) 996 return PTR_ERR(st->avdd); 997 998 ret = regulator_enable(st->avdd); 999 if (ret) { 1000 dev_err(&spi->dev, "Failed to enable specified AVdd supply\n"); 1001 return ret; 1002 } 1003 1004 ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->avdd); 1005 if (ret) 1006 return ret; 1007 1008 ret = devm_regulator_get_enable(&spi->dev, "dvdd"); 1009 if (ret) 1010 return dev_err_probe(&spi->dev, ret, "Failed to enable specified DVdd supply\n"); 1011 1012 st->vref = devm_regulator_get_optional(&spi->dev, "vref"); 1013 if (IS_ERR(st->vref)) { 1014 if (PTR_ERR(st->vref) != -ENODEV) 1015 return PTR_ERR(st->vref); 1016 1017 ret = regulator_get_voltage(st->avdd); 1018 if (ret < 0) 1019 return dev_err_probe(&spi->dev, ret, 1020 "Device tree error, AVdd voltage undefined\n"); 1021 } else { 1022 ret = regulator_enable(st->vref); 1023 if (ret) { 1024 dev_err(&spi->dev, "Failed to enable specified Vref supply\n"); 1025 return ret; 1026 } 1027 1028 ret = devm_add_action_or_reset(&spi->dev, ad7192_reg_disable, st->vref); 1029 if (ret) 1030 return ret; 1031 1032 ret = regulator_get_voltage(st->vref); 1033 if (ret < 0) 1034 return dev_err_probe(&spi->dev, ret, 1035 "Device tree error, Vref voltage undefined\n"); 1036 } 1037 st->int_vref_mv = ret / 1000; 1038 1039 st->chip_info = of_device_get_match_data(&spi->dev); 1040 if (!st->chip_info) 1041 st->chip_info = (void *)spi_get_device_id(spi)->driver_data; 1042 indio_dev->name = st->chip_info->name; 1043 indio_dev->modes = INDIO_DIRECT_MODE; 1044 1045 ret = ad7192_channels_config(indio_dev); 1046 if (ret < 0) 1047 return ret; 1048 1049 if (st->chip_info->chip_id == CHIPID_AD7195) 1050 indio_dev->info = &ad7195_info; 1051 else 1052 indio_dev->info = &ad7192_info; 1053 1054 ret = ad_sd_init(&st->sd, indio_dev, spi, &ad7192_sigma_delta_info); 1055 if (ret) 1056 return ret; 1057 1058 ret = devm_ad_sd_setup_buffer_and_trigger(&spi->dev, indio_dev); 1059 if (ret) 1060 return ret; 1061 1062 st->fclk = AD7192_INT_FREQ_MHZ; 1063 1064 st->mclk = devm_clk_get_optional_enabled(&spi->dev, "mclk"); 1065 if (IS_ERR(st->mclk)) 1066 return PTR_ERR(st->mclk); 1067 1068 st->clock_sel = ad7192_of_clock_select(st); 1069 1070 if (st->clock_sel == AD7192_CLK_EXT_MCLK1_2 || 1071 st->clock_sel == AD7192_CLK_EXT_MCLK2) { 1072 st->fclk = clk_get_rate(st->mclk); 1073 if (!ad7192_valid_external_frequency(st->fclk)) { 1074 dev_err(&spi->dev, 1075 "External clock frequency out of bounds\n"); 1076 return -EINVAL; 1077 } 1078 } 1079 1080 ret = ad7192_setup(indio_dev, spi->dev.of_node); 1081 if (ret) 1082 return ret; 1083 1084 return devm_iio_device_register(&spi->dev, indio_dev); 1085 } 1086 1087 static const struct of_device_id ad7192_of_match[] = { 1088 { .compatible = "adi,ad7190", .data = &ad7192_chip_info_tbl[ID_AD7190] }, 1089 { .compatible = "adi,ad7192", .data = &ad7192_chip_info_tbl[ID_AD7192] }, 1090 { .compatible = "adi,ad7193", .data = &ad7192_chip_info_tbl[ID_AD7193] }, 1091 { .compatible = "adi,ad7195", .data = &ad7192_chip_info_tbl[ID_AD7195] }, 1092 {} 1093 }; 1094 MODULE_DEVICE_TABLE(of, ad7192_of_match); 1095 1096 static const struct spi_device_id ad7192_ids[] = { 1097 { "ad7190", (kernel_ulong_t)&ad7192_chip_info_tbl[ID_AD7190] }, 1098 { "ad7192", (kernel_ulong_t)&ad7192_chip_info_tbl[ID_AD7192] }, 1099 { "ad7193", (kernel_ulong_t)&ad7192_chip_info_tbl[ID_AD7193] }, 1100 { "ad7195", (kernel_ulong_t)&ad7192_chip_info_tbl[ID_AD7195] }, 1101 {} 1102 }; 1103 MODULE_DEVICE_TABLE(spi, ad7192_ids); 1104 1105 static struct spi_driver ad7192_driver = { 1106 .driver = { 1107 .name = "ad7192", 1108 .of_match_table = ad7192_of_match, 1109 }, 1110 .probe = ad7192_probe, 1111 .id_table = ad7192_ids, 1112 }; 1113 module_spi_driver(ad7192_driver); 1114 1115 MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); 1116 MODULE_DESCRIPTION("Analog Devices AD7190, AD7192, AD7193, AD7195 ADC"); 1117 MODULE_LICENSE("GPL v2"); 1118 MODULE_IMPORT_NS(IIO_AD_SIGMA_DELTA); 1119