1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * bma180.c - IIO driver for Bosch BMA180 triaxial acceleration sensor 4 * 5 * Copyright 2013 Oleksandr Kravchenko <x0199363@ti.com> 6 * 7 * Support for BMA250 (c) Peter Meerwald <pmeerw@pmeerw.net> 8 * 9 * SPI is not supported by driver 10 * BMA023/BMA150/SMB380: 7-bit I2C slave address 0x38 11 * BMA180: 7-bit I2C slave address 0x40 or 0x41 12 * BMA250: 7-bit I2C slave address 0x18 or 0x19 13 * BMA254: 7-bit I2C slave address 0x18 or 0x19 14 */ 15 16 #include <linux/module.h> 17 #include <linux/i2c.h> 18 #include <linux/interrupt.h> 19 #include <linux/delay.h> 20 #include <linux/of_device.h> 21 #include <linux/of.h> 22 #include <linux/bitops.h> 23 #include <linux/regulator/consumer.h> 24 #include <linux/slab.h> 25 #include <linux/string.h> 26 #include <linux/iio/iio.h> 27 #include <linux/iio/sysfs.h> 28 #include <linux/iio/buffer.h> 29 #include <linux/iio/trigger.h> 30 #include <linux/iio/trigger_consumer.h> 31 #include <linux/iio/triggered_buffer.h> 32 33 #define BMA180_DRV_NAME "bma180" 34 #define BMA180_IRQ_NAME "bma180_event" 35 36 enum chip_ids { 37 BMA023, 38 BMA150, 39 BMA180, 40 BMA250, 41 BMA254, 42 }; 43 44 struct bma180_data; 45 46 struct bma180_part_info { 47 u8 chip_id; 48 const struct iio_chan_spec *channels; 49 unsigned int num_channels; 50 const int *scale_table; 51 unsigned int num_scales; 52 const int *bw_table; 53 unsigned int num_bw; 54 int temp_offset; 55 56 u8 int_reset_reg, int_reset_mask; 57 u8 sleep_reg, sleep_mask; 58 u8 bw_reg, bw_mask; 59 u8 scale_reg, scale_mask; 60 u8 power_reg, power_mask, lowpower_val; 61 u8 int_enable_reg, int_enable_mask; 62 u8 int_map_reg, int_enable_dataready_int1_mask; 63 u8 softreset_reg, softreset_val; 64 65 int (*chip_config)(struct bma180_data *data); 66 void (*chip_disable)(struct bma180_data *data); 67 }; 68 69 /* Register set */ 70 #define BMA023_CTRL_REG0 0x0a 71 #define BMA023_CTRL_REG1 0x0b 72 #define BMA023_CTRL_REG2 0x14 73 #define BMA023_CTRL_REG3 0x15 74 75 #define BMA023_RANGE_MASK GENMASK(4, 3) /* Range of accel values */ 76 #define BMA023_BW_MASK GENMASK(2, 0) /* Accel bandwidth */ 77 #define BMA023_SLEEP BIT(0) 78 #define BMA023_INT_RESET_MASK BIT(6) 79 #define BMA023_NEW_DATA_INT BIT(5) /* Intr every new accel data is ready */ 80 #define BMA023_RESET_VAL BIT(1) 81 82 #define BMA180_CHIP_ID 0x00 /* Need to distinguish BMA180 from other */ 83 #define BMA180_ACC_X_LSB 0x02 /* First of 6 registers of accel data */ 84 #define BMA180_TEMP 0x08 85 #define BMA180_CTRL_REG0 0x0d 86 #define BMA180_RESET 0x10 87 #define BMA180_BW_TCS 0x20 88 #define BMA180_CTRL_REG3 0x21 89 #define BMA180_TCO_Z 0x30 90 #define BMA180_OFFSET_LSB1 0x35 91 92 /* BMA180_CTRL_REG0 bits */ 93 #define BMA180_DIS_WAKE_UP BIT(0) /* Disable wake up mode */ 94 #define BMA180_SLEEP BIT(1) /* 1 - chip will sleep */ 95 #define BMA180_EE_W BIT(4) /* Unlock writing to addr from 0x20 */ 96 #define BMA180_RESET_INT BIT(6) /* Reset pending interrupts */ 97 98 /* BMA180_CTRL_REG3 bits */ 99 #define BMA180_NEW_DATA_INT BIT(1) /* Intr every new accel data is ready */ 100 101 /* BMA180_OFFSET_LSB1 skipping mode bit */ 102 #define BMA180_SMP_SKIP BIT(0) 103 104 /* Bit masks for registers bit fields */ 105 #define BMA180_RANGE 0x0e /* Range of measured accel values */ 106 #define BMA180_BW 0xf0 /* Accel bandwidth */ 107 #define BMA180_MODE_CONFIG 0x03 /* Config operation modes */ 108 109 /* We have to write this value in reset register to do soft reset */ 110 #define BMA180_RESET_VAL 0xb6 111 112 #define BMA023_ID_REG_VAL 0x02 113 #define BMA180_ID_REG_VAL 0x03 114 #define BMA250_ID_REG_VAL 0x03 115 #define BMA254_ID_REG_VAL 0xfa /* 250 decimal */ 116 117 /* Chip power modes */ 118 #define BMA180_LOW_POWER 0x03 119 120 #define BMA250_RANGE_REG 0x0f 121 #define BMA250_BW_REG 0x10 122 #define BMA250_POWER_REG 0x11 123 #define BMA250_RESET_REG 0x14 124 #define BMA250_INT_ENABLE_REG 0x17 125 #define BMA250_INT_MAP_REG 0x1a 126 #define BMA250_INT_RESET_REG 0x21 127 128 #define BMA250_RANGE_MASK GENMASK(3, 0) /* Range of accel values */ 129 #define BMA250_BW_MASK GENMASK(4, 0) /* Accel bandwidth */ 130 #define BMA250_SUSPEND_MASK BIT(7) /* chip will sleep */ 131 #define BMA250_LOWPOWER_MASK BIT(6) 132 #define BMA250_DATA_INTEN_MASK BIT(4) 133 #define BMA250_INT1_DATA_MASK BIT(0) 134 #define BMA250_INT_RESET_MASK BIT(7) /* Reset pending interrupts */ 135 136 #define BMA254_RANGE_REG 0x0f 137 #define BMA254_BW_REG 0x10 138 #define BMA254_POWER_REG 0x11 139 #define BMA254_RESET_REG 0x14 140 #define BMA254_INT_ENABLE_REG 0x17 141 #define BMA254_INT_MAP_REG 0x1a 142 #define BMA254_INT_RESET_REG 0x21 143 144 #define BMA254_RANGE_MASK GENMASK(3, 0) /* Range of accel values */ 145 #define BMA254_BW_MASK GENMASK(4, 0) /* Accel bandwidth */ 146 #define BMA254_SUSPEND_MASK BIT(7) /* chip will sleep */ 147 #define BMA254_LOWPOWER_MASK BIT(6) 148 #define BMA254_DATA_INTEN_MASK BIT(4) 149 #define BMA254_INT2_DATA_MASK BIT(7) 150 #define BMA254_INT1_DATA_MASK BIT(0) 151 #define BMA254_INT_RESET_MASK BIT(7) /* Reset pending interrupts */ 152 153 struct bma180_data { 154 struct regulator *vdd_supply; 155 struct regulator *vddio_supply; 156 struct i2c_client *client; 157 struct iio_trigger *trig; 158 const struct bma180_part_info *part_info; 159 struct iio_mount_matrix orientation; 160 struct mutex mutex; 161 bool sleep_state; 162 int scale; 163 int bw; 164 bool pmode; 165 u8 buff[16]; /* 3x 16-bit + 8-bit + padding + timestamp */ 166 }; 167 168 enum bma180_chan { 169 AXIS_X, 170 AXIS_Y, 171 AXIS_Z, 172 TEMP 173 }; 174 175 static int bma023_bw_table[] = { 25, 50, 100, 190, 375, 750, 1500 }; /* Hz */ 176 static int bma023_scale_table[] = { 2452, 4903, 9709, }; 177 178 static int bma180_bw_table[] = { 10, 20, 40, 75, 150, 300 }; /* Hz */ 179 static int bma180_scale_table[] = { 1275, 1863, 2452, 3727, 4903, 9709, 19417 }; 180 181 static int bma25x_bw_table[] = { 8, 16, 31, 63, 125, 250 }; /* Hz */ 182 static int bma25x_scale_table[] = { 0, 0, 0, 38344, 0, 76590, 0, 0, 153180, 0, 183 0, 0, 306458 }; 184 185 static int bma180_get_data_reg(struct bma180_data *data, enum bma180_chan chan) 186 { 187 int ret; 188 189 if (data->sleep_state) 190 return -EBUSY; 191 192 switch (chan) { 193 case TEMP: 194 ret = i2c_smbus_read_byte_data(data->client, BMA180_TEMP); 195 if (ret < 0) 196 dev_err(&data->client->dev, "failed to read temp register\n"); 197 break; 198 default: 199 ret = i2c_smbus_read_word_data(data->client, 200 BMA180_ACC_X_LSB + chan * 2); 201 if (ret < 0) 202 dev_err(&data->client->dev, 203 "failed to read accel_%c register\n", 204 'x' + chan); 205 } 206 207 return ret; 208 } 209 210 static int bma180_set_bits(struct bma180_data *data, u8 reg, u8 mask, u8 val) 211 { 212 int ret = i2c_smbus_read_byte_data(data->client, reg); 213 u8 reg_val = (ret & ~mask) | (val << (ffs(mask) - 1)); 214 215 if (ret < 0) 216 return ret; 217 218 return i2c_smbus_write_byte_data(data->client, reg, reg_val); 219 } 220 221 static int bma180_reset_intr(struct bma180_data *data) 222 { 223 int ret = bma180_set_bits(data, data->part_info->int_reset_reg, 224 data->part_info->int_reset_mask, 1); 225 226 if (ret) 227 dev_err(&data->client->dev, "failed to reset interrupt\n"); 228 229 return ret; 230 } 231 232 static int bma180_set_new_data_intr_state(struct bma180_data *data, bool state) 233 { 234 int ret = bma180_set_bits(data, data->part_info->int_enable_reg, 235 data->part_info->int_enable_mask, state); 236 if (ret) 237 goto err; 238 ret = bma180_reset_intr(data); 239 if (ret) 240 goto err; 241 242 return 0; 243 244 err: 245 dev_err(&data->client->dev, 246 "failed to set new data interrupt state %d\n", state); 247 return ret; 248 } 249 250 static int bma180_set_sleep_state(struct bma180_data *data, bool state) 251 { 252 int ret = bma180_set_bits(data, data->part_info->sleep_reg, 253 data->part_info->sleep_mask, state); 254 255 if (ret) { 256 dev_err(&data->client->dev, 257 "failed to set sleep state %d\n", state); 258 return ret; 259 } 260 data->sleep_state = state; 261 262 return 0; 263 } 264 265 static int bma180_set_ee_writing_state(struct bma180_data *data, bool state) 266 { 267 int ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_EE_W, state); 268 269 if (ret) 270 dev_err(&data->client->dev, 271 "failed to set ee writing state %d\n", state); 272 273 return ret; 274 } 275 276 static int bma180_set_bw(struct bma180_data *data, int val) 277 { 278 int ret, i; 279 280 if (data->sleep_state) 281 return -EBUSY; 282 283 for (i = 0; i < data->part_info->num_bw; ++i) { 284 if (data->part_info->bw_table[i] == val) { 285 ret = bma180_set_bits(data, data->part_info->bw_reg, 286 data->part_info->bw_mask, i); 287 if (ret) { 288 dev_err(&data->client->dev, 289 "failed to set bandwidth\n"); 290 return ret; 291 } 292 data->bw = val; 293 return 0; 294 } 295 } 296 297 return -EINVAL; 298 } 299 300 static int bma180_set_scale(struct bma180_data *data, int val) 301 { 302 int ret, i; 303 304 if (data->sleep_state) 305 return -EBUSY; 306 307 for (i = 0; i < data->part_info->num_scales; ++i) 308 if (data->part_info->scale_table[i] == val) { 309 ret = bma180_set_bits(data, data->part_info->scale_reg, 310 data->part_info->scale_mask, i); 311 if (ret) { 312 dev_err(&data->client->dev, 313 "failed to set scale\n"); 314 return ret; 315 } 316 data->scale = val; 317 return 0; 318 } 319 320 return -EINVAL; 321 } 322 323 static int bma180_set_pmode(struct bma180_data *data, bool mode) 324 { 325 u8 reg_val = mode ? data->part_info->lowpower_val : 0; 326 int ret = bma180_set_bits(data, data->part_info->power_reg, 327 data->part_info->power_mask, reg_val); 328 329 if (ret) { 330 dev_err(&data->client->dev, "failed to set power mode\n"); 331 return ret; 332 } 333 data->pmode = mode; 334 335 return 0; 336 } 337 338 static int bma180_soft_reset(struct bma180_data *data) 339 { 340 int ret = i2c_smbus_write_byte_data(data->client, 341 data->part_info->softreset_reg, 342 data->part_info->softreset_val); 343 344 if (ret) 345 dev_err(&data->client->dev, "failed to reset the chip\n"); 346 347 return ret; 348 } 349 350 static int bma180_chip_init(struct bma180_data *data) 351 { 352 /* Try to read chip_id register. It must return 0x03. */ 353 int ret = i2c_smbus_read_byte_data(data->client, BMA180_CHIP_ID); 354 355 if (ret < 0) 356 return ret; 357 if (ret != data->part_info->chip_id) { 358 dev_err(&data->client->dev, "wrong chip ID %d expected %d\n", 359 ret, data->part_info->chip_id); 360 return -ENODEV; 361 } 362 363 ret = bma180_soft_reset(data); 364 if (ret) 365 return ret; 366 /* 367 * No serial transaction should occur within minimum 10 us 368 * after soft_reset command 369 */ 370 msleep(20); 371 372 return bma180_set_new_data_intr_state(data, false); 373 } 374 375 static int bma023_chip_config(struct bma180_data *data) 376 { 377 int ret = bma180_chip_init(data); 378 379 if (ret) 380 goto err; 381 382 ret = bma180_set_bw(data, 50); /* 50 Hz */ 383 if (ret) 384 goto err; 385 ret = bma180_set_scale(data, 2452); /* 2 G */ 386 if (ret) 387 goto err; 388 389 return 0; 390 391 err: 392 dev_err(&data->client->dev, "failed to config the chip\n"); 393 return ret; 394 } 395 396 static int bma180_chip_config(struct bma180_data *data) 397 { 398 int ret = bma180_chip_init(data); 399 400 if (ret) 401 goto err; 402 ret = bma180_set_pmode(data, false); 403 if (ret) 404 goto err; 405 ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_DIS_WAKE_UP, 1); 406 if (ret) 407 goto err; 408 ret = bma180_set_ee_writing_state(data, true); 409 if (ret) 410 goto err; 411 ret = bma180_set_bits(data, BMA180_OFFSET_LSB1, BMA180_SMP_SKIP, 1); 412 if (ret) 413 goto err; 414 ret = bma180_set_bw(data, 20); /* 20 Hz */ 415 if (ret) 416 goto err; 417 ret = bma180_set_scale(data, 2452); /* 2 G */ 418 if (ret) 419 goto err; 420 421 return 0; 422 423 err: 424 dev_err(&data->client->dev, "failed to config the chip\n"); 425 return ret; 426 } 427 428 static int bma25x_chip_config(struct bma180_data *data) 429 { 430 int ret = bma180_chip_init(data); 431 432 if (ret) 433 goto err; 434 ret = bma180_set_pmode(data, false); 435 if (ret) 436 goto err; 437 ret = bma180_set_bw(data, 16); /* 16 Hz */ 438 if (ret) 439 goto err; 440 ret = bma180_set_scale(data, 38344); /* 2 G */ 441 if (ret) 442 goto err; 443 /* 444 * This enables dataready interrupt on the INT1 pin 445 * FIXME: support using the INT2 pin 446 */ 447 ret = bma180_set_bits(data, data->part_info->int_map_reg, 448 data->part_info->int_enable_dataready_int1_mask, 1); 449 if (ret) 450 goto err; 451 452 return 0; 453 454 err: 455 dev_err(&data->client->dev, "failed to config the chip\n"); 456 return ret; 457 } 458 459 static void bma023_chip_disable(struct bma180_data *data) 460 { 461 if (bma180_set_sleep_state(data, true)) 462 goto err; 463 464 return; 465 466 err: 467 dev_err(&data->client->dev, "failed to disable the chip\n"); 468 } 469 470 static void bma180_chip_disable(struct bma180_data *data) 471 { 472 if (bma180_set_new_data_intr_state(data, false)) 473 goto err; 474 if (bma180_set_ee_writing_state(data, false)) 475 goto err; 476 if (bma180_set_sleep_state(data, true)) 477 goto err; 478 479 return; 480 481 err: 482 dev_err(&data->client->dev, "failed to disable the chip\n"); 483 } 484 485 static void bma25x_chip_disable(struct bma180_data *data) 486 { 487 if (bma180_set_new_data_intr_state(data, false)) 488 goto err; 489 if (bma180_set_sleep_state(data, true)) 490 goto err; 491 492 return; 493 494 err: 495 dev_err(&data->client->dev, "failed to disable the chip\n"); 496 } 497 498 static ssize_t bma180_show_avail(char *buf, const int *vals, unsigned int n, 499 bool micros) 500 { 501 size_t len = 0; 502 int i; 503 504 for (i = 0; i < n; i++) { 505 if (!vals[i]) 506 continue; 507 len += scnprintf(buf + len, PAGE_SIZE - len, 508 micros ? "0.%06d " : "%d ", vals[i]); 509 } 510 buf[len - 1] = '\n'; 511 512 return len; 513 } 514 515 static ssize_t bma180_show_filter_freq_avail(struct device *dev, 516 struct device_attribute *attr, char *buf) 517 { 518 struct bma180_data *data = iio_priv(dev_to_iio_dev(dev)); 519 520 return bma180_show_avail(buf, data->part_info->bw_table, 521 data->part_info->num_bw, false); 522 } 523 524 static ssize_t bma180_show_scale_avail(struct device *dev, 525 struct device_attribute *attr, char *buf) 526 { 527 struct bma180_data *data = iio_priv(dev_to_iio_dev(dev)); 528 529 return bma180_show_avail(buf, data->part_info->scale_table, 530 data->part_info->num_scales, true); 531 } 532 533 static IIO_DEVICE_ATTR(in_accel_filter_low_pass_3db_frequency_available, 534 S_IRUGO, bma180_show_filter_freq_avail, NULL, 0); 535 536 static IIO_DEVICE_ATTR(in_accel_scale_available, 537 S_IRUGO, bma180_show_scale_avail, NULL, 0); 538 539 static struct attribute *bma180_attributes[] = { 540 &iio_dev_attr_in_accel_filter_low_pass_3db_frequency_available. 541 dev_attr.attr, 542 &iio_dev_attr_in_accel_scale_available.dev_attr.attr, 543 NULL, 544 }; 545 546 static const struct attribute_group bma180_attrs_group = { 547 .attrs = bma180_attributes, 548 }; 549 550 static int bma180_read_raw(struct iio_dev *indio_dev, 551 struct iio_chan_spec const *chan, int *val, int *val2, 552 long mask) 553 { 554 struct bma180_data *data = iio_priv(indio_dev); 555 int ret; 556 557 switch (mask) { 558 case IIO_CHAN_INFO_RAW: 559 ret = iio_device_claim_direct_mode(indio_dev); 560 if (ret) 561 return ret; 562 563 mutex_lock(&data->mutex); 564 ret = bma180_get_data_reg(data, chan->scan_index); 565 mutex_unlock(&data->mutex); 566 iio_device_release_direct_mode(indio_dev); 567 if (ret < 0) 568 return ret; 569 if (chan->scan_type.sign == 's') { 570 *val = sign_extend32(ret >> chan->scan_type.shift, 571 chan->scan_type.realbits - 1); 572 } else { 573 *val = ret; 574 } 575 return IIO_VAL_INT; 576 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 577 *val = data->bw; 578 return IIO_VAL_INT; 579 case IIO_CHAN_INFO_SCALE: 580 switch (chan->type) { 581 case IIO_ACCEL: 582 *val = 0; 583 *val2 = data->scale; 584 return IIO_VAL_INT_PLUS_MICRO; 585 case IIO_TEMP: 586 *val = 500; 587 return IIO_VAL_INT; 588 default: 589 return -EINVAL; 590 } 591 case IIO_CHAN_INFO_OFFSET: 592 *val = data->part_info->temp_offset; 593 return IIO_VAL_INT; 594 default: 595 return -EINVAL; 596 } 597 } 598 599 static int bma180_write_raw(struct iio_dev *indio_dev, 600 struct iio_chan_spec const *chan, int val, int val2, long mask) 601 { 602 struct bma180_data *data = iio_priv(indio_dev); 603 int ret; 604 605 switch (mask) { 606 case IIO_CHAN_INFO_SCALE: 607 if (val) 608 return -EINVAL; 609 mutex_lock(&data->mutex); 610 ret = bma180_set_scale(data, val2); 611 mutex_unlock(&data->mutex); 612 return ret; 613 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 614 if (val2) 615 return -EINVAL; 616 mutex_lock(&data->mutex); 617 ret = bma180_set_bw(data, val); 618 mutex_unlock(&data->mutex); 619 return ret; 620 default: 621 return -EINVAL; 622 } 623 } 624 625 static const struct iio_info bma180_info = { 626 .attrs = &bma180_attrs_group, 627 .read_raw = bma180_read_raw, 628 .write_raw = bma180_write_raw, 629 }; 630 631 static const char * const bma180_power_modes[] = { "low_noise", "low_power" }; 632 633 static int bma180_get_power_mode(struct iio_dev *indio_dev, 634 const struct iio_chan_spec *chan) 635 { 636 struct bma180_data *data = iio_priv(indio_dev); 637 638 return data->pmode; 639 } 640 641 static int bma180_set_power_mode(struct iio_dev *indio_dev, 642 const struct iio_chan_spec *chan, unsigned int mode) 643 { 644 struct bma180_data *data = iio_priv(indio_dev); 645 int ret; 646 647 mutex_lock(&data->mutex); 648 ret = bma180_set_pmode(data, mode); 649 mutex_unlock(&data->mutex); 650 651 return ret; 652 } 653 654 static const struct iio_mount_matrix * 655 bma180_accel_get_mount_matrix(const struct iio_dev *indio_dev, 656 const struct iio_chan_spec *chan) 657 { 658 struct bma180_data *data = iio_priv(indio_dev); 659 660 return &data->orientation; 661 } 662 663 static const struct iio_enum bma180_power_mode_enum = { 664 .items = bma180_power_modes, 665 .num_items = ARRAY_SIZE(bma180_power_modes), 666 .get = bma180_get_power_mode, 667 .set = bma180_set_power_mode, 668 }; 669 670 static const struct iio_chan_spec_ext_info bma023_ext_info[] = { 671 IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, bma180_accel_get_mount_matrix), 672 { } 673 }; 674 675 static const struct iio_chan_spec_ext_info bma180_ext_info[] = { 676 IIO_ENUM("power_mode", IIO_SHARED_BY_TYPE, &bma180_power_mode_enum), 677 IIO_ENUM_AVAILABLE("power_mode", &bma180_power_mode_enum), 678 IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, bma180_accel_get_mount_matrix), 679 { } 680 }; 681 682 #define BMA023_ACC_CHANNEL(_axis, _bits) { \ 683 .type = IIO_ACCEL, \ 684 .modified = 1, \ 685 .channel2 = IIO_MOD_##_axis, \ 686 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 687 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \ 688 BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), \ 689 .scan_index = AXIS_##_axis, \ 690 .scan_type = { \ 691 .sign = 's', \ 692 .realbits = _bits, \ 693 .storagebits = 16, \ 694 .shift = 16 - _bits, \ 695 }, \ 696 .ext_info = bma023_ext_info, \ 697 } 698 699 #define BMA150_TEMP_CHANNEL { \ 700 .type = IIO_TEMP, \ 701 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ 702 BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_OFFSET), \ 703 .scan_index = TEMP, \ 704 .scan_type = { \ 705 .sign = 'u', \ 706 .realbits = 8, \ 707 .storagebits = 16, \ 708 }, \ 709 } 710 711 #define BMA180_ACC_CHANNEL(_axis, _bits) { \ 712 .type = IIO_ACCEL, \ 713 .modified = 1, \ 714 .channel2 = IIO_MOD_##_axis, \ 715 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 716 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \ 717 BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), \ 718 .scan_index = AXIS_##_axis, \ 719 .scan_type = { \ 720 .sign = 's', \ 721 .realbits = _bits, \ 722 .storagebits = 16, \ 723 .shift = 16 - _bits, \ 724 }, \ 725 .ext_info = bma180_ext_info, \ 726 } 727 728 #define BMA180_TEMP_CHANNEL { \ 729 .type = IIO_TEMP, \ 730 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ 731 BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_OFFSET), \ 732 .scan_index = TEMP, \ 733 .scan_type = { \ 734 .sign = 's', \ 735 .realbits = 8, \ 736 .storagebits = 16, \ 737 }, \ 738 } 739 740 static const struct iio_chan_spec bma023_channels[] = { 741 BMA023_ACC_CHANNEL(X, 10), 742 BMA023_ACC_CHANNEL(Y, 10), 743 BMA023_ACC_CHANNEL(Z, 10), 744 IIO_CHAN_SOFT_TIMESTAMP(4), 745 }; 746 747 static const struct iio_chan_spec bma150_channels[] = { 748 BMA023_ACC_CHANNEL(X, 10), 749 BMA023_ACC_CHANNEL(Y, 10), 750 BMA023_ACC_CHANNEL(Z, 10), 751 BMA150_TEMP_CHANNEL, 752 IIO_CHAN_SOFT_TIMESTAMP(4), 753 }; 754 755 static const struct iio_chan_spec bma180_channels[] = { 756 BMA180_ACC_CHANNEL(X, 14), 757 BMA180_ACC_CHANNEL(Y, 14), 758 BMA180_ACC_CHANNEL(Z, 14), 759 BMA180_TEMP_CHANNEL, 760 IIO_CHAN_SOFT_TIMESTAMP(4), 761 }; 762 763 static const struct iio_chan_spec bma250_channels[] = { 764 BMA180_ACC_CHANNEL(X, 10), 765 BMA180_ACC_CHANNEL(Y, 10), 766 BMA180_ACC_CHANNEL(Z, 10), 767 BMA180_TEMP_CHANNEL, 768 IIO_CHAN_SOFT_TIMESTAMP(4), 769 }; 770 771 static const struct iio_chan_spec bma254_channels[] = { 772 BMA180_ACC_CHANNEL(X, 12), 773 BMA180_ACC_CHANNEL(Y, 12), 774 BMA180_ACC_CHANNEL(Z, 12), 775 BMA180_TEMP_CHANNEL, 776 IIO_CHAN_SOFT_TIMESTAMP(4), 777 }; 778 779 static const struct bma180_part_info bma180_part_info[] = { 780 [BMA023] = { 781 .chip_id = BMA023_ID_REG_VAL, 782 .channels = bma023_channels, 783 .num_channels = ARRAY_SIZE(bma023_channels), 784 .scale_table = bma023_scale_table, 785 .num_scales = ARRAY_SIZE(bma023_scale_table), 786 .bw_table = bma023_bw_table, 787 .num_bw = ARRAY_SIZE(bma023_bw_table), 788 /* No temperature channel */ 789 .temp_offset = 0, 790 .int_reset_reg = BMA023_CTRL_REG0, 791 .int_reset_mask = BMA023_INT_RESET_MASK, 792 .sleep_reg = BMA023_CTRL_REG0, 793 .sleep_mask = BMA023_SLEEP, 794 .bw_reg = BMA023_CTRL_REG2, 795 .bw_mask = BMA023_BW_MASK, 796 .scale_reg = BMA023_CTRL_REG2, 797 .scale_mask = BMA023_RANGE_MASK, 798 /* No power mode on bma023 */ 799 .power_reg = 0, 800 .power_mask = 0, 801 .lowpower_val = 0, 802 .int_enable_reg = BMA023_CTRL_REG3, 803 .int_enable_mask = BMA023_NEW_DATA_INT, 804 .softreset_reg = BMA023_CTRL_REG0, 805 .softreset_val = BMA023_RESET_VAL, 806 .chip_config = bma023_chip_config, 807 .chip_disable = bma023_chip_disable, 808 }, 809 [BMA150] = { 810 .chip_id = BMA023_ID_REG_VAL, 811 .channels = bma150_channels, 812 .num_channels = ARRAY_SIZE(bma150_channels), 813 .scale_table = bma023_scale_table, 814 .num_scales = ARRAY_SIZE(bma023_scale_table), 815 .bw_table = bma023_bw_table, 816 .num_bw = ARRAY_SIZE(bma023_bw_table), 817 .temp_offset = -60, /* 0 LSB @ -30 degree C */ 818 .int_reset_reg = BMA023_CTRL_REG0, 819 .int_reset_mask = BMA023_INT_RESET_MASK, 820 .sleep_reg = BMA023_CTRL_REG0, 821 .sleep_mask = BMA023_SLEEP, 822 .bw_reg = BMA023_CTRL_REG2, 823 .bw_mask = BMA023_BW_MASK, 824 .scale_reg = BMA023_CTRL_REG2, 825 .scale_mask = BMA023_RANGE_MASK, 826 /* No power mode on bma150 */ 827 .power_reg = 0, 828 .power_mask = 0, 829 .lowpower_val = 0, 830 .int_enable_reg = BMA023_CTRL_REG3, 831 .int_enable_mask = BMA023_NEW_DATA_INT, 832 .softreset_reg = BMA023_CTRL_REG0, 833 .softreset_val = BMA023_RESET_VAL, 834 .chip_config = bma023_chip_config, 835 .chip_disable = bma023_chip_disable, 836 }, 837 [BMA180] = { 838 .chip_id = BMA180_ID_REG_VAL, 839 .channels = bma180_channels, 840 .num_channels = ARRAY_SIZE(bma180_channels), 841 .scale_table = bma180_scale_table, 842 .num_scales = ARRAY_SIZE(bma180_scale_table), 843 .bw_table = bma180_bw_table, 844 .num_bw = ARRAY_SIZE(bma180_bw_table), 845 .temp_offset = 48, /* 0 LSB @ 24 degree C */ 846 .int_reset_reg = BMA180_CTRL_REG0, 847 .int_reset_mask = BMA180_RESET_INT, 848 .sleep_reg = BMA180_CTRL_REG0, 849 .sleep_mask = BMA180_SLEEP, 850 .bw_reg = BMA180_BW_TCS, 851 .bw_mask = BMA180_BW, 852 .scale_reg = BMA180_OFFSET_LSB1, 853 .scale_mask = BMA180_RANGE, 854 .power_reg = BMA180_TCO_Z, 855 .power_mask = BMA180_MODE_CONFIG, 856 .lowpower_val = BMA180_LOW_POWER, 857 .int_enable_reg = BMA180_CTRL_REG3, 858 .int_enable_mask = BMA180_NEW_DATA_INT, 859 .softreset_reg = BMA180_RESET, 860 .softreset_val = BMA180_RESET_VAL, 861 .chip_config = bma180_chip_config, 862 .chip_disable = bma180_chip_disable, 863 }, 864 [BMA250] = { 865 .chip_id = BMA250_ID_REG_VAL, 866 .channels = bma250_channels, 867 .num_channels = ARRAY_SIZE(bma250_channels), 868 .scale_table = bma25x_scale_table, 869 .num_scales = ARRAY_SIZE(bma25x_scale_table), 870 .bw_table = bma25x_bw_table, 871 .num_bw = ARRAY_SIZE(bma25x_bw_table), 872 .temp_offset = 48, /* 0 LSB @ 24 degree C */ 873 .int_reset_reg = BMA250_INT_RESET_REG, 874 .int_reset_mask = BMA250_INT_RESET_MASK, 875 .sleep_reg = BMA250_POWER_REG, 876 .sleep_mask = BMA250_SUSPEND_MASK, 877 .bw_reg = BMA250_BW_REG, 878 .bw_mask = BMA250_BW_MASK, 879 .scale_reg = BMA250_RANGE_REG, 880 .scale_mask = BMA250_RANGE_MASK, 881 .power_reg = BMA250_POWER_REG, 882 .power_mask = BMA250_LOWPOWER_MASK, 883 .lowpower_val = 1, 884 .int_enable_reg = BMA250_INT_ENABLE_REG, 885 .int_enable_mask = BMA250_DATA_INTEN_MASK, 886 .int_map_reg = BMA250_INT_MAP_REG, 887 .int_enable_dataready_int1_mask = BMA250_INT1_DATA_MASK, 888 .softreset_reg = BMA250_RESET_REG, 889 .softreset_val = BMA180_RESET_VAL, 890 .chip_config = bma25x_chip_config, 891 .chip_disable = bma25x_chip_disable, 892 }, 893 [BMA254] = { 894 .chip_id = BMA254_ID_REG_VAL, 895 .channels = bma254_channels, 896 .num_channels = ARRAY_SIZE(bma254_channels), 897 .scale_table = bma25x_scale_table, 898 .num_scales = ARRAY_SIZE(bma25x_scale_table), 899 .bw_table = bma25x_bw_table, 900 .num_bw = ARRAY_SIZE(bma25x_bw_table), 901 .temp_offset = 46, /* 0 LSB @ 23 degree C */ 902 .int_reset_reg = BMA254_INT_RESET_REG, 903 .int_reset_mask = BMA254_INT_RESET_MASK, 904 .sleep_reg = BMA254_POWER_REG, 905 .sleep_mask = BMA254_SUSPEND_MASK, 906 .bw_reg = BMA254_BW_REG, 907 .bw_mask = BMA254_BW_MASK, 908 .scale_reg = BMA254_RANGE_REG, 909 .scale_mask = BMA254_RANGE_MASK, 910 .power_reg = BMA254_POWER_REG, 911 .power_mask = BMA254_LOWPOWER_MASK, 912 .lowpower_val = 1, 913 .int_enable_reg = BMA254_INT_ENABLE_REG, 914 .int_enable_mask = BMA254_DATA_INTEN_MASK, 915 .int_map_reg = BMA254_INT_MAP_REG, 916 .int_enable_dataready_int1_mask = BMA254_INT1_DATA_MASK, 917 .softreset_reg = BMA254_RESET_REG, 918 .softreset_val = BMA180_RESET_VAL, 919 .chip_config = bma25x_chip_config, 920 .chip_disable = bma25x_chip_disable, 921 }, 922 }; 923 924 static irqreturn_t bma180_trigger_handler(int irq, void *p) 925 { 926 struct iio_poll_func *pf = p; 927 struct iio_dev *indio_dev = pf->indio_dev; 928 struct bma180_data *data = iio_priv(indio_dev); 929 s64 time_ns = iio_get_time_ns(indio_dev); 930 int bit, ret, i = 0; 931 932 mutex_lock(&data->mutex); 933 934 for_each_set_bit(bit, indio_dev->active_scan_mask, 935 indio_dev->masklength) { 936 ret = bma180_get_data_reg(data, bit); 937 if (ret < 0) { 938 mutex_unlock(&data->mutex); 939 goto err; 940 } 941 ((s16 *)data->buff)[i++] = ret; 942 } 943 944 mutex_unlock(&data->mutex); 945 946 iio_push_to_buffers_with_timestamp(indio_dev, data->buff, time_ns); 947 err: 948 iio_trigger_notify_done(indio_dev->trig); 949 950 return IRQ_HANDLED; 951 } 952 953 static int bma180_data_rdy_trigger_set_state(struct iio_trigger *trig, 954 bool state) 955 { 956 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 957 struct bma180_data *data = iio_priv(indio_dev); 958 959 return bma180_set_new_data_intr_state(data, state); 960 } 961 962 static int bma180_trig_try_reen(struct iio_trigger *trig) 963 { 964 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 965 struct bma180_data *data = iio_priv(indio_dev); 966 967 return bma180_reset_intr(data); 968 } 969 970 static const struct iio_trigger_ops bma180_trigger_ops = { 971 .set_trigger_state = bma180_data_rdy_trigger_set_state, 972 .try_reenable = bma180_trig_try_reen, 973 }; 974 975 static int bma180_probe(struct i2c_client *client, 976 const struct i2c_device_id *id) 977 { 978 struct device *dev = &client->dev; 979 struct bma180_data *data; 980 struct iio_dev *indio_dev; 981 enum chip_ids chip; 982 int ret; 983 984 indio_dev = devm_iio_device_alloc(dev, sizeof(*data)); 985 if (!indio_dev) 986 return -ENOMEM; 987 988 data = iio_priv(indio_dev); 989 i2c_set_clientdata(client, indio_dev); 990 data->client = client; 991 if (client->dev.of_node) 992 chip = (enum chip_ids)of_device_get_match_data(dev); 993 else 994 chip = id->driver_data; 995 data->part_info = &bma180_part_info[chip]; 996 997 ret = iio_read_mount_matrix(dev, "mount-matrix", 998 &data->orientation); 999 if (ret) 1000 return ret; 1001 1002 data->vdd_supply = devm_regulator_get(dev, "vdd"); 1003 if (IS_ERR(data->vdd_supply)) 1004 return dev_err_probe(dev, PTR_ERR(data->vdd_supply), 1005 "Failed to get vdd regulator\n"); 1006 1007 data->vddio_supply = devm_regulator_get(dev, "vddio"); 1008 if (IS_ERR(data->vddio_supply)) 1009 return dev_err_probe(dev, PTR_ERR(data->vddio_supply), 1010 "Failed to get vddio regulator\n"); 1011 1012 /* Typical voltage 2.4V these are min and max */ 1013 ret = regulator_set_voltage(data->vdd_supply, 1620000, 3600000); 1014 if (ret) 1015 return ret; 1016 ret = regulator_set_voltage(data->vddio_supply, 1200000, 3600000); 1017 if (ret) 1018 return ret; 1019 ret = regulator_enable(data->vdd_supply); 1020 if (ret) { 1021 dev_err(dev, "Failed to enable vdd regulator: %d\n", ret); 1022 return ret; 1023 } 1024 ret = regulator_enable(data->vddio_supply); 1025 if (ret) { 1026 dev_err(dev, "Failed to enable vddio regulator: %d\n", ret); 1027 goto err_disable_vdd; 1028 } 1029 /* Wait to make sure we started up properly (3 ms at least) */ 1030 usleep_range(3000, 5000); 1031 1032 ret = data->part_info->chip_config(data); 1033 if (ret < 0) 1034 goto err_chip_disable; 1035 1036 mutex_init(&data->mutex); 1037 indio_dev->channels = data->part_info->channels; 1038 indio_dev->num_channels = data->part_info->num_channels; 1039 indio_dev->name = id->name; 1040 indio_dev->modes = INDIO_DIRECT_MODE; 1041 indio_dev->info = &bma180_info; 1042 1043 if (client->irq > 0) { 1044 data->trig = iio_trigger_alloc("%s-dev%d", indio_dev->name, 1045 indio_dev->id); 1046 if (!data->trig) { 1047 ret = -ENOMEM; 1048 goto err_chip_disable; 1049 } 1050 1051 ret = devm_request_irq(dev, client->irq, 1052 iio_trigger_generic_data_rdy_poll, IRQF_TRIGGER_RISING, 1053 "bma180_event", data->trig); 1054 if (ret) { 1055 dev_err(dev, "unable to request IRQ\n"); 1056 goto err_trigger_free; 1057 } 1058 1059 data->trig->dev.parent = dev; 1060 data->trig->ops = &bma180_trigger_ops; 1061 iio_trigger_set_drvdata(data->trig, indio_dev); 1062 indio_dev->trig = iio_trigger_get(data->trig); 1063 1064 ret = iio_trigger_register(data->trig); 1065 if (ret) 1066 goto err_trigger_free; 1067 } 1068 1069 ret = iio_triggered_buffer_setup(indio_dev, NULL, 1070 bma180_trigger_handler, NULL); 1071 if (ret < 0) { 1072 dev_err(dev, "unable to setup iio triggered buffer\n"); 1073 goto err_trigger_unregister; 1074 } 1075 1076 ret = iio_device_register(indio_dev); 1077 if (ret < 0) { 1078 dev_err(dev, "unable to register iio device\n"); 1079 goto err_buffer_cleanup; 1080 } 1081 1082 return 0; 1083 1084 err_buffer_cleanup: 1085 iio_triggered_buffer_cleanup(indio_dev); 1086 err_trigger_unregister: 1087 if (data->trig) 1088 iio_trigger_unregister(data->trig); 1089 err_trigger_free: 1090 iio_trigger_free(data->trig); 1091 err_chip_disable: 1092 data->part_info->chip_disable(data); 1093 regulator_disable(data->vddio_supply); 1094 err_disable_vdd: 1095 regulator_disable(data->vdd_supply); 1096 1097 return ret; 1098 } 1099 1100 static int bma180_remove(struct i2c_client *client) 1101 { 1102 struct iio_dev *indio_dev = i2c_get_clientdata(client); 1103 struct bma180_data *data = iio_priv(indio_dev); 1104 1105 iio_device_unregister(indio_dev); 1106 iio_triggered_buffer_cleanup(indio_dev); 1107 if (data->trig) { 1108 iio_trigger_unregister(data->trig); 1109 iio_trigger_free(data->trig); 1110 } 1111 1112 mutex_lock(&data->mutex); 1113 data->part_info->chip_disable(data); 1114 mutex_unlock(&data->mutex); 1115 regulator_disable(data->vddio_supply); 1116 regulator_disable(data->vdd_supply); 1117 1118 return 0; 1119 } 1120 1121 #ifdef CONFIG_PM_SLEEP 1122 static int bma180_suspend(struct device *dev) 1123 { 1124 struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); 1125 struct bma180_data *data = iio_priv(indio_dev); 1126 int ret; 1127 1128 mutex_lock(&data->mutex); 1129 ret = bma180_set_sleep_state(data, true); 1130 mutex_unlock(&data->mutex); 1131 1132 return ret; 1133 } 1134 1135 static int bma180_resume(struct device *dev) 1136 { 1137 struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); 1138 struct bma180_data *data = iio_priv(indio_dev); 1139 int ret; 1140 1141 mutex_lock(&data->mutex); 1142 ret = bma180_set_sleep_state(data, false); 1143 mutex_unlock(&data->mutex); 1144 1145 return ret; 1146 } 1147 1148 static SIMPLE_DEV_PM_OPS(bma180_pm_ops, bma180_suspend, bma180_resume); 1149 #define BMA180_PM_OPS (&bma180_pm_ops) 1150 #else 1151 #define BMA180_PM_OPS NULL 1152 #endif 1153 1154 static const struct i2c_device_id bma180_ids[] = { 1155 { "bma023", BMA023 }, 1156 { "bma150", BMA150 }, 1157 { "bma180", BMA180 }, 1158 { "bma250", BMA250 }, 1159 { "bma254", BMA254 }, 1160 { "smb380", BMA150 }, 1161 { } 1162 }; 1163 1164 MODULE_DEVICE_TABLE(i2c, bma180_ids); 1165 1166 static const struct of_device_id bma180_of_match[] = { 1167 { 1168 .compatible = "bosch,bma023", 1169 .data = (void *)BMA023 1170 }, 1171 { 1172 .compatible = "bosch,bma150", 1173 .data = (void *)BMA150 1174 }, 1175 { 1176 .compatible = "bosch,bma180", 1177 .data = (void *)BMA180 1178 }, 1179 { 1180 .compatible = "bosch,bma250", 1181 .data = (void *)BMA250 1182 }, 1183 { 1184 .compatible = "bosch,bma254", 1185 .data = (void *)BMA254 1186 }, 1187 { 1188 .compatible = "bosch,smb380", 1189 .data = (void *)BMA150 1190 }, 1191 { } 1192 }; 1193 MODULE_DEVICE_TABLE(of, bma180_of_match); 1194 1195 static struct i2c_driver bma180_driver = { 1196 .driver = { 1197 .name = "bma180", 1198 .pm = BMA180_PM_OPS, 1199 .of_match_table = bma180_of_match, 1200 }, 1201 .probe = bma180_probe, 1202 .remove = bma180_remove, 1203 .id_table = bma180_ids, 1204 }; 1205 1206 module_i2c_driver(bma180_driver); 1207 1208 MODULE_AUTHOR("Kravchenko Oleksandr <x0199363@ti.com>"); 1209 MODULE_AUTHOR("Texas Instruments, Inc."); 1210 MODULE_DESCRIPTION("Bosch BMA023/BMA1x0/BMA25x triaxial acceleration sensor"); 1211 MODULE_LICENSE("GPL"); 1212