1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Driver for I2C adapter in Rockchip RK3xxx SoC 4 * 5 * Max Schwarz <max.schwarz@online.de> 6 * based on the patches by Rockchip Inc. 7 */ 8 9 #include <linux/kernel.h> 10 #include <linux/module.h> 11 #include <linux/i2c.h> 12 #include <linux/interrupt.h> 13 #include <linux/iopoll.h> 14 #include <linux/errno.h> 15 #include <linux/err.h> 16 #include <linux/platform_device.h> 17 #include <linux/io.h> 18 #include <linux/of_address.h> 19 #include <linux/of_irq.h> 20 #include <linux/spinlock.h> 21 #include <linux/clk.h> 22 #include <linux/wait.h> 23 #include <linux/mfd/syscon.h> 24 #include <linux/regmap.h> 25 #include <linux/math64.h> 26 27 28 /* Register Map */ 29 #define REG_CON 0x00 /* control register */ 30 #define REG_CLKDIV 0x04 /* clock divisor register */ 31 #define REG_MRXADDR 0x08 /* slave address for REGISTER_TX */ 32 #define REG_MRXRADDR 0x0c /* slave register address for REGISTER_TX */ 33 #define REG_MTXCNT 0x10 /* number of bytes to be transmitted */ 34 #define REG_MRXCNT 0x14 /* number of bytes to be received */ 35 #define REG_IEN 0x18 /* interrupt enable */ 36 #define REG_IPD 0x1c /* interrupt pending */ 37 #define REG_FCNT 0x20 /* finished count */ 38 39 /* Data buffer offsets */ 40 #define TXBUFFER_BASE 0x100 41 #define RXBUFFER_BASE 0x200 42 43 /* REG_CON bits */ 44 #define REG_CON_EN BIT(0) 45 enum { 46 REG_CON_MOD_TX = 0, /* transmit data */ 47 REG_CON_MOD_REGISTER_TX, /* select register and restart */ 48 REG_CON_MOD_RX, /* receive data */ 49 REG_CON_MOD_REGISTER_RX, /* broken: transmits read addr AND writes 50 * register addr */ 51 }; 52 #define REG_CON_MOD(mod) ((mod) << 1) 53 #define REG_CON_MOD_MASK (BIT(1) | BIT(2)) 54 #define REG_CON_START BIT(3) 55 #define REG_CON_STOP BIT(4) 56 #define REG_CON_LASTACK BIT(5) /* 1: send NACK after last received byte */ 57 #define REG_CON_ACTACK BIT(6) /* 1: stop if NACK is received */ 58 59 #define REG_CON_TUNING_MASK GENMASK_ULL(15, 8) 60 61 #define REG_CON_SDA_CFG(cfg) ((cfg) << 8) 62 #define REG_CON_STA_CFG(cfg) ((cfg) << 12) 63 #define REG_CON_STO_CFG(cfg) ((cfg) << 14) 64 65 /* REG_MRXADDR bits */ 66 #define REG_MRXADDR_VALID(x) BIT(24 + (x)) /* [x*8+7:x*8] of MRX[R]ADDR valid */ 67 68 /* REG_IEN/REG_IPD bits */ 69 #define REG_INT_BTF BIT(0) /* a byte was transmitted */ 70 #define REG_INT_BRF BIT(1) /* a byte was received */ 71 #define REG_INT_MBTF BIT(2) /* master data transmit finished */ 72 #define REG_INT_MBRF BIT(3) /* master data receive finished */ 73 #define REG_INT_START BIT(4) /* START condition generated */ 74 #define REG_INT_STOP BIT(5) /* STOP condition generated */ 75 #define REG_INT_NAKRCV BIT(6) /* NACK received */ 76 #define REG_INT_ALL 0x7f 77 78 /* Constants */ 79 #define WAIT_TIMEOUT 1000 /* ms */ 80 #define DEFAULT_SCL_RATE (100 * 1000) /* Hz */ 81 82 /** 83 * struct i2c_spec_values: 84 * @min_hold_start_ns: min hold time (repeated) START condition 85 * @min_low_ns: min LOW period of the SCL clock 86 * @min_high_ns: min HIGH period of the SCL cloc 87 * @min_setup_start_ns: min set-up time for a repeated START conditio 88 * @max_data_hold_ns: max data hold time 89 * @min_data_setup_ns: min data set-up time 90 * @min_setup_stop_ns: min set-up time for STOP condition 91 * @min_hold_buffer_ns: min bus free time between a STOP and 92 * START condition 93 */ 94 struct i2c_spec_values { 95 unsigned long min_hold_start_ns; 96 unsigned long min_low_ns; 97 unsigned long min_high_ns; 98 unsigned long min_setup_start_ns; 99 unsigned long max_data_hold_ns; 100 unsigned long min_data_setup_ns; 101 unsigned long min_setup_stop_ns; 102 unsigned long min_hold_buffer_ns; 103 }; 104 105 static const struct i2c_spec_values standard_mode_spec = { 106 .min_hold_start_ns = 4000, 107 .min_low_ns = 4700, 108 .min_high_ns = 4000, 109 .min_setup_start_ns = 4700, 110 .max_data_hold_ns = 3450, 111 .min_data_setup_ns = 250, 112 .min_setup_stop_ns = 4000, 113 .min_hold_buffer_ns = 4700, 114 }; 115 116 static const struct i2c_spec_values fast_mode_spec = { 117 .min_hold_start_ns = 600, 118 .min_low_ns = 1300, 119 .min_high_ns = 600, 120 .min_setup_start_ns = 600, 121 .max_data_hold_ns = 900, 122 .min_data_setup_ns = 100, 123 .min_setup_stop_ns = 600, 124 .min_hold_buffer_ns = 1300, 125 }; 126 127 static const struct i2c_spec_values fast_mode_plus_spec = { 128 .min_hold_start_ns = 260, 129 .min_low_ns = 500, 130 .min_high_ns = 260, 131 .min_setup_start_ns = 260, 132 .max_data_hold_ns = 400, 133 .min_data_setup_ns = 50, 134 .min_setup_stop_ns = 260, 135 .min_hold_buffer_ns = 500, 136 }; 137 138 /** 139 * struct rk3x_i2c_calced_timings: 140 * @div_low: Divider output for low 141 * @div_high: Divider output for high 142 * @tuning: Used to adjust setup/hold data time, 143 * setup/hold start time and setup stop time for 144 * v1's calc_timings, the tuning should all be 0 145 * for old hardware anyone using v0's calc_timings. 146 */ 147 struct rk3x_i2c_calced_timings { 148 unsigned long div_low; 149 unsigned long div_high; 150 unsigned int tuning; 151 }; 152 153 enum rk3x_i2c_state { 154 STATE_IDLE, 155 STATE_START, 156 STATE_READ, 157 STATE_WRITE, 158 STATE_STOP 159 }; 160 161 /** 162 * struct rk3x_i2c_soc_data: 163 * @grf_offset: offset inside the grf regmap for setting the i2c type 164 * @calc_timings: Callback function for i2c timing information calculated 165 */ 166 struct rk3x_i2c_soc_data { 167 int grf_offset; 168 int (*calc_timings)(unsigned long, struct i2c_timings *, 169 struct rk3x_i2c_calced_timings *); 170 }; 171 172 /** 173 * struct rk3x_i2c - private data of the controller 174 * @adap: corresponding I2C adapter 175 * @dev: device for this controller 176 * @soc_data: related soc data struct 177 * @regs: virtual memory area 178 * @clk: function clk for rk3399 or function & Bus clks for others 179 * @pclk: Bus clk for rk3399 180 * @clk_rate_nb: i2c clk rate change notify 181 * @t: I2C known timing information 182 * @lock: spinlock for the i2c bus 183 * @wait: the waitqueue to wait for i2c transfer 184 * @busy: the condition for the event to wait for 185 * @msg: current i2c message 186 * @addr: addr of i2c slave device 187 * @mode: mode of i2c transfer 188 * @is_last_msg: flag determines whether it is the last msg in this transfer 189 * @state: state of i2c transfer 190 * @processed: byte length which has been send or received 191 * @error: error code for i2c transfer 192 */ 193 struct rk3x_i2c { 194 struct i2c_adapter adap; 195 struct device *dev; 196 const struct rk3x_i2c_soc_data *soc_data; 197 198 /* Hardware resources */ 199 void __iomem *regs; 200 struct clk *clk; 201 struct clk *pclk; 202 struct notifier_block clk_rate_nb; 203 204 /* Settings */ 205 struct i2c_timings t; 206 207 /* Synchronization & notification */ 208 spinlock_t lock; 209 wait_queue_head_t wait; 210 bool busy; 211 212 /* Current message */ 213 struct i2c_msg *msg; 214 u8 addr; 215 unsigned int mode; 216 bool is_last_msg; 217 218 /* I2C state machine */ 219 enum rk3x_i2c_state state; 220 unsigned int processed; 221 int error; 222 }; 223 224 static inline void i2c_writel(struct rk3x_i2c *i2c, u32 value, 225 unsigned int offset) 226 { 227 writel(value, i2c->regs + offset); 228 } 229 230 static inline u32 i2c_readl(struct rk3x_i2c *i2c, unsigned int offset) 231 { 232 return readl(i2c->regs + offset); 233 } 234 235 /* Reset all interrupt pending bits */ 236 static inline void rk3x_i2c_clean_ipd(struct rk3x_i2c *i2c) 237 { 238 i2c_writel(i2c, REG_INT_ALL, REG_IPD); 239 } 240 241 /** 242 * Generate a START condition, which triggers a REG_INT_START interrupt. 243 */ 244 static void rk3x_i2c_start(struct rk3x_i2c *i2c) 245 { 246 u32 val = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 247 248 i2c_writel(i2c, REG_INT_START, REG_IEN); 249 250 /* enable adapter with correct mode, send START condition */ 251 val |= REG_CON_EN | REG_CON_MOD(i2c->mode) | REG_CON_START; 252 253 /* if we want to react to NACK, set ACTACK bit */ 254 if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) 255 val |= REG_CON_ACTACK; 256 257 i2c_writel(i2c, val, REG_CON); 258 } 259 260 /** 261 * Generate a STOP condition, which triggers a REG_INT_STOP interrupt. 262 * 263 * @error: Error code to return in rk3x_i2c_xfer 264 */ 265 static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error) 266 { 267 unsigned int ctrl; 268 269 i2c->processed = 0; 270 i2c->msg = NULL; 271 i2c->error = error; 272 273 if (i2c->is_last_msg) { 274 /* Enable stop interrupt */ 275 i2c_writel(i2c, REG_INT_STOP, REG_IEN); 276 277 i2c->state = STATE_STOP; 278 279 ctrl = i2c_readl(i2c, REG_CON); 280 ctrl |= REG_CON_STOP; 281 i2c_writel(i2c, ctrl, REG_CON); 282 } else { 283 /* Signal rk3x_i2c_xfer to start the next message. */ 284 i2c->busy = false; 285 i2c->state = STATE_IDLE; 286 287 /* 288 * The HW is actually not capable of REPEATED START. But we can 289 * get the intended effect by resetting its internal state 290 * and issuing an ordinary START. 291 */ 292 ctrl = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 293 i2c_writel(i2c, ctrl, REG_CON); 294 295 /* signal that we are finished with the current msg */ 296 wake_up(&i2c->wait); 297 } 298 } 299 300 /** 301 * Setup a read according to i2c->msg 302 */ 303 static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c) 304 { 305 unsigned int len = i2c->msg->len - i2c->processed; 306 u32 con; 307 308 con = i2c_readl(i2c, REG_CON); 309 310 /* 311 * The hw can read up to 32 bytes at a time. If we need more than one 312 * chunk, send an ACK after the last byte of the current chunk. 313 */ 314 if (len > 32) { 315 len = 32; 316 con &= ~REG_CON_LASTACK; 317 } else { 318 con |= REG_CON_LASTACK; 319 } 320 321 /* make sure we are in plain RX mode if we read a second chunk */ 322 if (i2c->processed != 0) { 323 con &= ~REG_CON_MOD_MASK; 324 con |= REG_CON_MOD(REG_CON_MOD_RX); 325 } 326 327 i2c_writel(i2c, con, REG_CON); 328 i2c_writel(i2c, len, REG_MRXCNT); 329 } 330 331 /** 332 * Fill the transmit buffer with data from i2c->msg 333 */ 334 static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c) 335 { 336 unsigned int i, j; 337 u32 cnt = 0; 338 u32 val; 339 u8 byte; 340 341 for (i = 0; i < 8; ++i) { 342 val = 0; 343 for (j = 0; j < 4; ++j) { 344 if ((i2c->processed == i2c->msg->len) && (cnt != 0)) 345 break; 346 347 if (i2c->processed == 0 && cnt == 0) 348 byte = (i2c->addr & 0x7f) << 1; 349 else 350 byte = i2c->msg->buf[i2c->processed++]; 351 352 val |= byte << (j * 8); 353 cnt++; 354 } 355 356 i2c_writel(i2c, val, TXBUFFER_BASE + 4 * i); 357 358 if (i2c->processed == i2c->msg->len) 359 break; 360 } 361 362 i2c_writel(i2c, cnt, REG_MTXCNT); 363 } 364 365 366 /* IRQ handlers for individual states */ 367 368 static void rk3x_i2c_handle_start(struct rk3x_i2c *i2c, unsigned int ipd) 369 { 370 if (!(ipd & REG_INT_START)) { 371 rk3x_i2c_stop(i2c, -EIO); 372 dev_warn(i2c->dev, "unexpected irq in START: 0x%x\n", ipd); 373 rk3x_i2c_clean_ipd(i2c); 374 return; 375 } 376 377 /* ack interrupt */ 378 i2c_writel(i2c, REG_INT_START, REG_IPD); 379 380 /* disable start bit */ 381 i2c_writel(i2c, i2c_readl(i2c, REG_CON) & ~REG_CON_START, REG_CON); 382 383 /* enable appropriate interrupts and transition */ 384 if (i2c->mode == REG_CON_MOD_TX) { 385 i2c_writel(i2c, REG_INT_MBTF | REG_INT_NAKRCV, REG_IEN); 386 i2c->state = STATE_WRITE; 387 rk3x_i2c_fill_transmit_buf(i2c); 388 } else { 389 /* in any other case, we are going to be reading. */ 390 i2c_writel(i2c, REG_INT_MBRF | REG_INT_NAKRCV, REG_IEN); 391 i2c->state = STATE_READ; 392 rk3x_i2c_prepare_read(i2c); 393 } 394 } 395 396 static void rk3x_i2c_handle_write(struct rk3x_i2c *i2c, unsigned int ipd) 397 { 398 if (!(ipd & REG_INT_MBTF)) { 399 rk3x_i2c_stop(i2c, -EIO); 400 dev_err(i2c->dev, "unexpected irq in WRITE: 0x%x\n", ipd); 401 rk3x_i2c_clean_ipd(i2c); 402 return; 403 } 404 405 /* ack interrupt */ 406 i2c_writel(i2c, REG_INT_MBTF, REG_IPD); 407 408 /* are we finished? */ 409 if (i2c->processed == i2c->msg->len) 410 rk3x_i2c_stop(i2c, i2c->error); 411 else 412 rk3x_i2c_fill_transmit_buf(i2c); 413 } 414 415 static void rk3x_i2c_handle_read(struct rk3x_i2c *i2c, unsigned int ipd) 416 { 417 unsigned int i; 418 unsigned int len = i2c->msg->len - i2c->processed; 419 u32 val; 420 u8 byte; 421 422 /* we only care for MBRF here. */ 423 if (!(ipd & REG_INT_MBRF)) 424 return; 425 426 /* ack interrupt */ 427 i2c_writel(i2c, REG_INT_MBRF, REG_IPD); 428 429 /* Can only handle a maximum of 32 bytes at a time */ 430 if (len > 32) 431 len = 32; 432 433 /* read the data from receive buffer */ 434 for (i = 0; i < len; ++i) { 435 if (i % 4 == 0) 436 val = i2c_readl(i2c, RXBUFFER_BASE + (i / 4) * 4); 437 438 byte = (val >> ((i % 4) * 8)) & 0xff; 439 i2c->msg->buf[i2c->processed++] = byte; 440 } 441 442 /* are we finished? */ 443 if (i2c->processed == i2c->msg->len) 444 rk3x_i2c_stop(i2c, i2c->error); 445 else 446 rk3x_i2c_prepare_read(i2c); 447 } 448 449 static void rk3x_i2c_handle_stop(struct rk3x_i2c *i2c, unsigned int ipd) 450 { 451 unsigned int con; 452 453 if (!(ipd & REG_INT_STOP)) { 454 rk3x_i2c_stop(i2c, -EIO); 455 dev_err(i2c->dev, "unexpected irq in STOP: 0x%x\n", ipd); 456 rk3x_i2c_clean_ipd(i2c); 457 return; 458 } 459 460 /* ack interrupt */ 461 i2c_writel(i2c, REG_INT_STOP, REG_IPD); 462 463 /* disable STOP bit */ 464 con = i2c_readl(i2c, REG_CON); 465 con &= ~REG_CON_STOP; 466 i2c_writel(i2c, con, REG_CON); 467 468 i2c->busy = false; 469 i2c->state = STATE_IDLE; 470 471 /* signal rk3x_i2c_xfer that we are finished */ 472 wake_up(&i2c->wait); 473 } 474 475 static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id) 476 { 477 struct rk3x_i2c *i2c = dev_id; 478 unsigned int ipd; 479 480 spin_lock(&i2c->lock); 481 482 ipd = i2c_readl(i2c, REG_IPD); 483 if (i2c->state == STATE_IDLE) { 484 dev_warn(i2c->dev, "irq in STATE_IDLE, ipd = 0x%x\n", ipd); 485 rk3x_i2c_clean_ipd(i2c); 486 goto out; 487 } 488 489 dev_dbg(i2c->dev, "IRQ: state %d, ipd: %x\n", i2c->state, ipd); 490 491 /* Clean interrupt bits we don't care about */ 492 ipd &= ~(REG_INT_BRF | REG_INT_BTF); 493 494 if (ipd & REG_INT_NAKRCV) { 495 /* 496 * We got a NACK in the last operation. Depending on whether 497 * IGNORE_NAK is set, we have to stop the operation and report 498 * an error. 499 */ 500 i2c_writel(i2c, REG_INT_NAKRCV, REG_IPD); 501 502 ipd &= ~REG_INT_NAKRCV; 503 504 if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) 505 rk3x_i2c_stop(i2c, -ENXIO); 506 } 507 508 /* is there anything left to handle? */ 509 if ((ipd & REG_INT_ALL) == 0) 510 goto out; 511 512 switch (i2c->state) { 513 case STATE_START: 514 rk3x_i2c_handle_start(i2c, ipd); 515 break; 516 case STATE_WRITE: 517 rk3x_i2c_handle_write(i2c, ipd); 518 break; 519 case STATE_READ: 520 rk3x_i2c_handle_read(i2c, ipd); 521 break; 522 case STATE_STOP: 523 rk3x_i2c_handle_stop(i2c, ipd); 524 break; 525 case STATE_IDLE: 526 break; 527 } 528 529 out: 530 spin_unlock(&i2c->lock); 531 return IRQ_HANDLED; 532 } 533 534 /** 535 * Get timing values of I2C specification 536 * 537 * @speed: Desired SCL frequency 538 * 539 * Returns: Matched i2c spec values. 540 */ 541 static const struct i2c_spec_values *rk3x_i2c_get_spec(unsigned int speed) 542 { 543 if (speed <= I2C_MAX_STANDARD_MODE_FREQ) 544 return &standard_mode_spec; 545 else if (speed <= I2C_MAX_FAST_MODE_FREQ) 546 return &fast_mode_spec; 547 else 548 return &fast_mode_plus_spec; 549 } 550 551 /** 552 * Calculate divider values for desired SCL frequency 553 * 554 * @clk_rate: I2C input clock rate 555 * @t: Known I2C timing information 556 * @t_calc: Caculated rk3x private timings that would be written into regs 557 * 558 * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case 559 * a best-effort divider value is returned in divs. If the target rate is 560 * too high, we silently use the highest possible rate. 561 */ 562 static int rk3x_i2c_v0_calc_timings(unsigned long clk_rate, 563 struct i2c_timings *t, 564 struct rk3x_i2c_calced_timings *t_calc) 565 { 566 unsigned long min_low_ns, min_high_ns; 567 unsigned long max_low_ns, min_total_ns; 568 569 unsigned long clk_rate_khz, scl_rate_khz; 570 571 unsigned long min_low_div, min_high_div; 572 unsigned long max_low_div; 573 574 unsigned long min_div_for_hold, min_total_div; 575 unsigned long extra_div, extra_low_div, ideal_low_div; 576 577 unsigned long data_hold_buffer_ns = 50; 578 const struct i2c_spec_values *spec; 579 int ret = 0; 580 581 /* Only support standard-mode and fast-mode */ 582 if (WARN_ON(t->bus_freq_hz > I2C_MAX_FAST_MODE_FREQ)) 583 t->bus_freq_hz = I2C_MAX_FAST_MODE_FREQ; 584 585 /* prevent scl_rate_khz from becoming 0 */ 586 if (WARN_ON(t->bus_freq_hz < 1000)) 587 t->bus_freq_hz = 1000; 588 589 /* 590 * min_low_ns: The minimum number of ns we need to hold low to 591 * meet I2C specification, should include fall time. 592 * min_high_ns: The minimum number of ns we need to hold high to 593 * meet I2C specification, should include rise time. 594 * max_low_ns: The maximum number of ns we can hold low to meet 595 * I2C specification. 596 * 597 * Note: max_low_ns should be (maximum data hold time * 2 - buffer) 598 * This is because the i2c host on Rockchip holds the data line 599 * for half the low time. 600 */ 601 spec = rk3x_i2c_get_spec(t->bus_freq_hz); 602 min_high_ns = t->scl_rise_ns + spec->min_high_ns; 603 604 /* 605 * Timings for repeated start: 606 * - controller appears to drop SDA at .875x (7/8) programmed clk high. 607 * - controller appears to keep SCL high for 2x programmed clk high. 608 * 609 * We need to account for those rules in picking our "high" time so 610 * we meet tSU;STA and tHD;STA times. 611 */ 612 min_high_ns = max(min_high_ns, DIV_ROUND_UP( 613 (t->scl_rise_ns + spec->min_setup_start_ns) * 1000, 875)); 614 min_high_ns = max(min_high_ns, DIV_ROUND_UP( 615 (t->scl_rise_ns + spec->min_setup_start_ns + t->sda_fall_ns + 616 spec->min_high_ns), 2)); 617 618 min_low_ns = t->scl_fall_ns + spec->min_low_ns; 619 max_low_ns = spec->max_data_hold_ns * 2 - data_hold_buffer_ns; 620 min_total_ns = min_low_ns + min_high_ns; 621 622 /* Adjust to avoid overflow */ 623 clk_rate_khz = DIV_ROUND_UP(clk_rate, 1000); 624 scl_rate_khz = t->bus_freq_hz / 1000; 625 626 /* 627 * We need the total div to be >= this number 628 * so we don't clock too fast. 629 */ 630 min_total_div = DIV_ROUND_UP(clk_rate_khz, scl_rate_khz * 8); 631 632 /* These are the min dividers needed for min hold times. */ 633 min_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 8 * 1000000); 634 min_high_div = DIV_ROUND_UP(clk_rate_khz * min_high_ns, 8 * 1000000); 635 min_div_for_hold = (min_low_div + min_high_div); 636 637 /* 638 * This is the maximum divider so we don't go over the maximum. 639 * We don't round up here (we round down) since this is a maximum. 640 */ 641 max_low_div = clk_rate_khz * max_low_ns / (8 * 1000000); 642 643 if (min_low_div > max_low_div) { 644 WARN_ONCE(true, 645 "Conflicting, min_low_div %lu, max_low_div %lu\n", 646 min_low_div, max_low_div); 647 max_low_div = min_low_div; 648 } 649 650 if (min_div_for_hold > min_total_div) { 651 /* 652 * Time needed to meet hold requirements is important. 653 * Just use that. 654 */ 655 t_calc->div_low = min_low_div; 656 t_calc->div_high = min_high_div; 657 } else { 658 /* 659 * We've got to distribute some time among the low and high 660 * so we don't run too fast. 661 */ 662 extra_div = min_total_div - min_div_for_hold; 663 664 /* 665 * We'll try to split things up perfectly evenly, 666 * biasing slightly towards having a higher div 667 * for low (spend more time low). 668 */ 669 ideal_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 670 scl_rate_khz * 8 * min_total_ns); 671 672 /* Don't allow it to go over the maximum */ 673 if (ideal_low_div > max_low_div) 674 ideal_low_div = max_low_div; 675 676 /* 677 * Handle when the ideal low div is going to take up 678 * more than we have. 679 */ 680 if (ideal_low_div > min_low_div + extra_div) 681 ideal_low_div = min_low_div + extra_div; 682 683 /* Give low the "ideal" and give high whatever extra is left */ 684 extra_low_div = ideal_low_div - min_low_div; 685 t_calc->div_low = ideal_low_div; 686 t_calc->div_high = min_high_div + (extra_div - extra_low_div); 687 } 688 689 /* 690 * Adjust to the fact that the hardware has an implicit "+1". 691 * NOTE: Above calculations always produce div_low > 0 and div_high > 0. 692 */ 693 t_calc->div_low--; 694 t_calc->div_high--; 695 696 /* Give the tuning value 0, that would not update con register */ 697 t_calc->tuning = 0; 698 /* Maximum divider supported by hw is 0xffff */ 699 if (t_calc->div_low > 0xffff) { 700 t_calc->div_low = 0xffff; 701 ret = -EINVAL; 702 } 703 704 if (t_calc->div_high > 0xffff) { 705 t_calc->div_high = 0xffff; 706 ret = -EINVAL; 707 } 708 709 return ret; 710 } 711 712 /** 713 * Calculate timing values for desired SCL frequency 714 * 715 * @clk_rate: I2C input clock rate 716 * @t: Known I2C timing information 717 * @t_calc: Caculated rk3x private timings that would be written into regs 718 * 719 * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case 720 * a best-effort divider value is returned in divs. If the target rate is 721 * too high, we silently use the highest possible rate. 722 * The following formulas are v1's method to calculate timings. 723 * 724 * l = divl + 1; 725 * h = divh + 1; 726 * s = sda_update_config + 1; 727 * u = start_setup_config + 1; 728 * p = stop_setup_config + 1; 729 * T = Tclk_i2c; 730 * 731 * tHigh = 8 * h * T; 732 * tLow = 8 * l * T; 733 * 734 * tHD;sda = (l * s + 1) * T; 735 * tSU;sda = [(8 - s) * l + 1] * T; 736 * tI2C = 8 * (l + h) * T; 737 * 738 * tSU;sta = (8h * u + 1) * T; 739 * tHD;sta = [8h * (u + 1) - 1] * T; 740 * tSU;sto = (8h * p + 1) * T; 741 */ 742 static int rk3x_i2c_v1_calc_timings(unsigned long clk_rate, 743 struct i2c_timings *t, 744 struct rk3x_i2c_calced_timings *t_calc) 745 { 746 unsigned long min_low_ns, min_high_ns; 747 unsigned long min_setup_start_ns, min_setup_data_ns; 748 unsigned long min_setup_stop_ns, max_hold_data_ns; 749 750 unsigned long clk_rate_khz, scl_rate_khz; 751 752 unsigned long min_low_div, min_high_div; 753 754 unsigned long min_div_for_hold, min_total_div; 755 unsigned long extra_div, extra_low_div; 756 unsigned long sda_update_cfg, stp_sta_cfg, stp_sto_cfg; 757 758 const struct i2c_spec_values *spec; 759 int ret = 0; 760 761 /* Support standard-mode, fast-mode and fast-mode plus */ 762 if (WARN_ON(t->bus_freq_hz > I2C_MAX_FAST_MODE_PLUS_FREQ)) 763 t->bus_freq_hz = I2C_MAX_FAST_MODE_PLUS_FREQ; 764 765 /* prevent scl_rate_khz from becoming 0 */ 766 if (WARN_ON(t->bus_freq_hz < 1000)) 767 t->bus_freq_hz = 1000; 768 769 /* 770 * min_low_ns: The minimum number of ns we need to hold low to 771 * meet I2C specification, should include fall time. 772 * min_high_ns: The minimum number of ns we need to hold high to 773 * meet I2C specification, should include rise time. 774 */ 775 spec = rk3x_i2c_get_spec(t->bus_freq_hz); 776 777 /* calculate min-divh and min-divl */ 778 clk_rate_khz = DIV_ROUND_UP(clk_rate, 1000); 779 scl_rate_khz = t->bus_freq_hz / 1000; 780 min_total_div = DIV_ROUND_UP(clk_rate_khz, scl_rate_khz * 8); 781 782 min_high_ns = t->scl_rise_ns + spec->min_high_ns; 783 min_high_div = DIV_ROUND_UP(clk_rate_khz * min_high_ns, 8 * 1000000); 784 785 min_low_ns = t->scl_fall_ns + spec->min_low_ns; 786 min_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 8 * 1000000); 787 788 /* 789 * Final divh and divl must be greater than 0, otherwise the 790 * hardware would not output the i2c clk. 791 */ 792 min_high_div = (min_high_div < 1) ? 2 : min_high_div; 793 min_low_div = (min_low_div < 1) ? 2 : min_low_div; 794 795 /* These are the min dividers needed for min hold times. */ 796 min_div_for_hold = (min_low_div + min_high_div); 797 798 /* 799 * This is the maximum divider so we don't go over the maximum. 800 * We don't round up here (we round down) since this is a maximum. 801 */ 802 if (min_div_for_hold >= min_total_div) { 803 /* 804 * Time needed to meet hold requirements is important. 805 * Just use that. 806 */ 807 t_calc->div_low = min_low_div; 808 t_calc->div_high = min_high_div; 809 } else { 810 /* 811 * We've got to distribute some time among the low and high 812 * so we don't run too fast. 813 * We'll try to split things up by the scale of min_low_div and 814 * min_high_div, biasing slightly towards having a higher div 815 * for low (spend more time low). 816 */ 817 extra_div = min_total_div - min_div_for_hold; 818 extra_low_div = DIV_ROUND_UP(min_low_div * extra_div, 819 min_div_for_hold); 820 821 t_calc->div_low = min_low_div + extra_low_div; 822 t_calc->div_high = min_high_div + (extra_div - extra_low_div); 823 } 824 825 /* 826 * calculate sda data hold count by the rules, data_upd_st:3 827 * is a appropriate value to reduce calculated times. 828 */ 829 for (sda_update_cfg = 3; sda_update_cfg > 0; sda_update_cfg--) { 830 max_hold_data_ns = DIV_ROUND_UP((sda_update_cfg 831 * (t_calc->div_low) + 1) 832 * 1000000, clk_rate_khz); 833 min_setup_data_ns = DIV_ROUND_UP(((8 - sda_update_cfg) 834 * (t_calc->div_low) + 1) 835 * 1000000, clk_rate_khz); 836 if ((max_hold_data_ns < spec->max_data_hold_ns) && 837 (min_setup_data_ns > spec->min_data_setup_ns)) 838 break; 839 } 840 841 /* calculate setup start config */ 842 min_setup_start_ns = t->scl_rise_ns + spec->min_setup_start_ns; 843 stp_sta_cfg = DIV_ROUND_UP(clk_rate_khz * min_setup_start_ns 844 - 1000000, 8 * 1000000 * (t_calc->div_high)); 845 846 /* calculate setup stop config */ 847 min_setup_stop_ns = t->scl_rise_ns + spec->min_setup_stop_ns; 848 stp_sto_cfg = DIV_ROUND_UP(clk_rate_khz * min_setup_stop_ns 849 - 1000000, 8 * 1000000 * (t_calc->div_high)); 850 851 t_calc->tuning = REG_CON_SDA_CFG(--sda_update_cfg) | 852 REG_CON_STA_CFG(--stp_sta_cfg) | 853 REG_CON_STO_CFG(--stp_sto_cfg); 854 855 t_calc->div_low--; 856 t_calc->div_high--; 857 858 /* Maximum divider supported by hw is 0xffff */ 859 if (t_calc->div_low > 0xffff) { 860 t_calc->div_low = 0xffff; 861 ret = -EINVAL; 862 } 863 864 if (t_calc->div_high > 0xffff) { 865 t_calc->div_high = 0xffff; 866 ret = -EINVAL; 867 } 868 869 return ret; 870 } 871 872 static void rk3x_i2c_adapt_div(struct rk3x_i2c *i2c, unsigned long clk_rate) 873 { 874 struct i2c_timings *t = &i2c->t; 875 struct rk3x_i2c_calced_timings calc; 876 u64 t_low_ns, t_high_ns; 877 unsigned long flags; 878 u32 val; 879 int ret; 880 881 ret = i2c->soc_data->calc_timings(clk_rate, t, &calc); 882 WARN_ONCE(ret != 0, "Could not reach SCL freq %u", t->bus_freq_hz); 883 884 clk_enable(i2c->pclk); 885 886 spin_lock_irqsave(&i2c->lock, flags); 887 val = i2c_readl(i2c, REG_CON); 888 val &= ~REG_CON_TUNING_MASK; 889 val |= calc.tuning; 890 i2c_writel(i2c, val, REG_CON); 891 i2c_writel(i2c, (calc.div_high << 16) | (calc.div_low & 0xffff), 892 REG_CLKDIV); 893 spin_unlock_irqrestore(&i2c->lock, flags); 894 895 clk_disable(i2c->pclk); 896 897 t_low_ns = div_u64(((u64)calc.div_low + 1) * 8 * 1000000000, clk_rate); 898 t_high_ns = div_u64(((u64)calc.div_high + 1) * 8 * 1000000000, 899 clk_rate); 900 dev_dbg(i2c->dev, 901 "CLK %lukhz, Req %uns, Act low %lluns high %lluns\n", 902 clk_rate / 1000, 903 1000000000 / t->bus_freq_hz, 904 t_low_ns, t_high_ns); 905 } 906 907 /** 908 * rk3x_i2c_clk_notifier_cb - Clock rate change callback 909 * @nb: Pointer to notifier block 910 * @event: Notification reason 911 * @data: Pointer to notification data object 912 * 913 * The callback checks whether a valid bus frequency can be generated after the 914 * change. If so, the change is acknowledged, otherwise the change is aborted. 915 * New dividers are written to the HW in the pre- or post change notification 916 * depending on the scaling direction. 917 * 918 * Code adapted from i2c-cadence.c. 919 * 920 * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK 921 * to acknowledge the change, NOTIFY_DONE if the notification is 922 * considered irrelevant. 923 */ 924 static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long 925 event, void *data) 926 { 927 struct clk_notifier_data *ndata = data; 928 struct rk3x_i2c *i2c = container_of(nb, struct rk3x_i2c, clk_rate_nb); 929 struct rk3x_i2c_calced_timings calc; 930 931 switch (event) { 932 case PRE_RATE_CHANGE: 933 /* 934 * Try the calculation (but don't store the result) ahead of 935 * time to see if we need to block the clock change. Timings 936 * shouldn't actually take effect until rk3x_i2c_adapt_div(). 937 */ 938 if (i2c->soc_data->calc_timings(ndata->new_rate, &i2c->t, 939 &calc) != 0) 940 return NOTIFY_STOP; 941 942 /* scale up */ 943 if (ndata->new_rate > ndata->old_rate) 944 rk3x_i2c_adapt_div(i2c, ndata->new_rate); 945 946 return NOTIFY_OK; 947 case POST_RATE_CHANGE: 948 /* scale down */ 949 if (ndata->new_rate < ndata->old_rate) 950 rk3x_i2c_adapt_div(i2c, ndata->new_rate); 951 return NOTIFY_OK; 952 case ABORT_RATE_CHANGE: 953 /* scale up */ 954 if (ndata->new_rate > ndata->old_rate) 955 rk3x_i2c_adapt_div(i2c, ndata->old_rate); 956 return NOTIFY_OK; 957 default: 958 return NOTIFY_DONE; 959 } 960 } 961 962 /** 963 * Setup I2C registers for an I2C operation specified by msgs, num. 964 * 965 * Must be called with i2c->lock held. 966 * 967 * @msgs: I2C msgs to process 968 * @num: Number of msgs 969 * 970 * returns: Number of I2C msgs processed or negative in case of error 971 */ 972 static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num) 973 { 974 u32 addr = (msgs[0].addr & 0x7f) << 1; 975 int ret = 0; 976 977 /* 978 * The I2C adapter can issue a small (len < 4) write packet before 979 * reading. This speeds up SMBus-style register reads. 980 * The MRXADDR/MRXRADDR hold the slave address and the slave register 981 * address in this case. 982 */ 983 984 if (num >= 2 && msgs[0].len < 4 && 985 !(msgs[0].flags & I2C_M_RD) && (msgs[1].flags & I2C_M_RD)) { 986 u32 reg_addr = 0; 987 int i; 988 989 dev_dbg(i2c->dev, "Combined write/read from addr 0x%x\n", 990 addr >> 1); 991 992 /* Fill MRXRADDR with the register address(es) */ 993 for (i = 0; i < msgs[0].len; ++i) { 994 reg_addr |= msgs[0].buf[i] << (i * 8); 995 reg_addr |= REG_MRXADDR_VALID(i); 996 } 997 998 /* msgs[0] is handled by hw. */ 999 i2c->msg = &msgs[1]; 1000 1001 i2c->mode = REG_CON_MOD_REGISTER_TX; 1002 1003 i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), REG_MRXADDR); 1004 i2c_writel(i2c, reg_addr, REG_MRXRADDR); 1005 1006 ret = 2; 1007 } else { 1008 /* 1009 * We'll have to do it the boring way and process the msgs 1010 * one-by-one. 1011 */ 1012 1013 if (msgs[0].flags & I2C_M_RD) { 1014 addr |= 1; /* set read bit */ 1015 1016 /* 1017 * We have to transmit the slave addr first. Use 1018 * MOD_REGISTER_TX for that purpose. 1019 */ 1020 i2c->mode = REG_CON_MOD_REGISTER_TX; 1021 i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), 1022 REG_MRXADDR); 1023 i2c_writel(i2c, 0, REG_MRXRADDR); 1024 } else { 1025 i2c->mode = REG_CON_MOD_TX; 1026 } 1027 1028 i2c->msg = &msgs[0]; 1029 1030 ret = 1; 1031 } 1032 1033 i2c->addr = msgs[0].addr; 1034 i2c->busy = true; 1035 i2c->state = STATE_START; 1036 i2c->processed = 0; 1037 i2c->error = 0; 1038 1039 rk3x_i2c_clean_ipd(i2c); 1040 1041 return ret; 1042 } 1043 1044 static int rk3x_i2c_wait_xfer_poll(struct rk3x_i2c *i2c) 1045 { 1046 ktime_t timeout = ktime_add_ms(ktime_get(), WAIT_TIMEOUT); 1047 1048 while (READ_ONCE(i2c->busy) && 1049 ktime_compare(ktime_get(), timeout) < 0) { 1050 udelay(5); 1051 rk3x_i2c_irq(0, i2c); 1052 } 1053 1054 return !i2c->busy; 1055 } 1056 1057 static int rk3x_i2c_xfer_common(struct i2c_adapter *adap, 1058 struct i2c_msg *msgs, int num, bool polling) 1059 { 1060 struct rk3x_i2c *i2c = (struct rk3x_i2c *)adap->algo_data; 1061 unsigned long timeout, flags; 1062 u32 val; 1063 int ret = 0; 1064 int i; 1065 1066 spin_lock_irqsave(&i2c->lock, flags); 1067 1068 clk_enable(i2c->clk); 1069 clk_enable(i2c->pclk); 1070 1071 i2c->is_last_msg = false; 1072 1073 /* 1074 * Process msgs. We can handle more than one message at once (see 1075 * rk3x_i2c_setup()). 1076 */ 1077 for (i = 0; i < num; i += ret) { 1078 ret = rk3x_i2c_setup(i2c, msgs + i, num - i); 1079 1080 if (ret < 0) { 1081 dev_err(i2c->dev, "rk3x_i2c_setup() failed\n"); 1082 break; 1083 } 1084 1085 if (i + ret >= num) 1086 i2c->is_last_msg = true; 1087 1088 spin_unlock_irqrestore(&i2c->lock, flags); 1089 1090 rk3x_i2c_start(i2c); 1091 1092 if (!polling) { 1093 timeout = wait_event_timeout(i2c->wait, !i2c->busy, 1094 msecs_to_jiffies(WAIT_TIMEOUT)); 1095 } else { 1096 timeout = rk3x_i2c_wait_xfer_poll(i2c); 1097 } 1098 1099 spin_lock_irqsave(&i2c->lock, flags); 1100 1101 if (timeout == 0) { 1102 dev_err(i2c->dev, "timeout, ipd: 0x%02x, state: %d\n", 1103 i2c_readl(i2c, REG_IPD), i2c->state); 1104 1105 /* Force a STOP condition without interrupt */ 1106 i2c_writel(i2c, 0, REG_IEN); 1107 val = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 1108 val |= REG_CON_EN | REG_CON_STOP; 1109 i2c_writel(i2c, val, REG_CON); 1110 1111 i2c->state = STATE_IDLE; 1112 1113 ret = -ETIMEDOUT; 1114 break; 1115 } 1116 1117 if (i2c->error) { 1118 ret = i2c->error; 1119 break; 1120 } 1121 } 1122 1123 clk_disable(i2c->pclk); 1124 clk_disable(i2c->clk); 1125 1126 spin_unlock_irqrestore(&i2c->lock, flags); 1127 1128 return ret < 0 ? ret : num; 1129 } 1130 1131 static int rk3x_i2c_xfer(struct i2c_adapter *adap, 1132 struct i2c_msg *msgs, int num) 1133 { 1134 return rk3x_i2c_xfer_common(adap, msgs, num, false); 1135 } 1136 1137 static int rk3x_i2c_xfer_polling(struct i2c_adapter *adap, 1138 struct i2c_msg *msgs, int num) 1139 { 1140 return rk3x_i2c_xfer_common(adap, msgs, num, true); 1141 } 1142 1143 static __maybe_unused int rk3x_i2c_resume(struct device *dev) 1144 { 1145 struct rk3x_i2c *i2c = dev_get_drvdata(dev); 1146 1147 rk3x_i2c_adapt_div(i2c, clk_get_rate(i2c->clk)); 1148 1149 return 0; 1150 } 1151 1152 static u32 rk3x_i2c_func(struct i2c_adapter *adap) 1153 { 1154 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING; 1155 } 1156 1157 static const struct i2c_algorithm rk3x_i2c_algorithm = { 1158 .master_xfer = rk3x_i2c_xfer, 1159 .master_xfer_atomic = rk3x_i2c_xfer_polling, 1160 .functionality = rk3x_i2c_func, 1161 }; 1162 1163 static const struct rk3x_i2c_soc_data rv1108_soc_data = { 1164 .grf_offset = -1, 1165 .calc_timings = rk3x_i2c_v1_calc_timings, 1166 }; 1167 1168 static const struct rk3x_i2c_soc_data rk3066_soc_data = { 1169 .grf_offset = 0x154, 1170 .calc_timings = rk3x_i2c_v0_calc_timings, 1171 }; 1172 1173 static const struct rk3x_i2c_soc_data rk3188_soc_data = { 1174 .grf_offset = 0x0a4, 1175 .calc_timings = rk3x_i2c_v0_calc_timings, 1176 }; 1177 1178 static const struct rk3x_i2c_soc_data rk3228_soc_data = { 1179 .grf_offset = -1, 1180 .calc_timings = rk3x_i2c_v0_calc_timings, 1181 }; 1182 1183 static const struct rk3x_i2c_soc_data rk3288_soc_data = { 1184 .grf_offset = -1, 1185 .calc_timings = rk3x_i2c_v0_calc_timings, 1186 }; 1187 1188 static const struct rk3x_i2c_soc_data rk3399_soc_data = { 1189 .grf_offset = -1, 1190 .calc_timings = rk3x_i2c_v1_calc_timings, 1191 }; 1192 1193 static const struct of_device_id rk3x_i2c_match[] = { 1194 { 1195 .compatible = "rockchip,rv1108-i2c", 1196 .data = &rv1108_soc_data 1197 }, 1198 { 1199 .compatible = "rockchip,rk3066-i2c", 1200 .data = &rk3066_soc_data 1201 }, 1202 { 1203 .compatible = "rockchip,rk3188-i2c", 1204 .data = &rk3188_soc_data 1205 }, 1206 { 1207 .compatible = "rockchip,rk3228-i2c", 1208 .data = &rk3228_soc_data 1209 }, 1210 { 1211 .compatible = "rockchip,rk3288-i2c", 1212 .data = &rk3288_soc_data 1213 }, 1214 { 1215 .compatible = "rockchip,rk3399-i2c", 1216 .data = &rk3399_soc_data 1217 }, 1218 {}, 1219 }; 1220 MODULE_DEVICE_TABLE(of, rk3x_i2c_match); 1221 1222 static int rk3x_i2c_probe(struct platform_device *pdev) 1223 { 1224 struct device_node *np = pdev->dev.of_node; 1225 const struct of_device_id *match; 1226 struct rk3x_i2c *i2c; 1227 int ret = 0; 1228 int bus_nr; 1229 u32 value; 1230 int irq; 1231 unsigned long clk_rate; 1232 1233 i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL); 1234 if (!i2c) 1235 return -ENOMEM; 1236 1237 match = of_match_node(rk3x_i2c_match, np); 1238 i2c->soc_data = match->data; 1239 1240 /* use common interface to get I2C timing properties */ 1241 i2c_parse_fw_timings(&pdev->dev, &i2c->t, true); 1242 1243 strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); 1244 i2c->adap.owner = THIS_MODULE; 1245 i2c->adap.algo = &rk3x_i2c_algorithm; 1246 i2c->adap.retries = 3; 1247 i2c->adap.dev.of_node = np; 1248 i2c->adap.algo_data = i2c; 1249 i2c->adap.dev.parent = &pdev->dev; 1250 1251 i2c->dev = &pdev->dev; 1252 1253 spin_lock_init(&i2c->lock); 1254 init_waitqueue_head(&i2c->wait); 1255 1256 i2c->regs = devm_platform_ioremap_resource(pdev, 0); 1257 if (IS_ERR(i2c->regs)) 1258 return PTR_ERR(i2c->regs); 1259 1260 /* Try to set the I2C adapter number from dt */ 1261 bus_nr = of_alias_get_id(np, "i2c"); 1262 1263 /* 1264 * Switch to new interface if the SoC also offers the old one. 1265 * The control bit is located in the GRF register space. 1266 */ 1267 if (i2c->soc_data->grf_offset >= 0) { 1268 struct regmap *grf; 1269 1270 grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); 1271 if (IS_ERR(grf)) { 1272 dev_err(&pdev->dev, 1273 "rk3x-i2c needs 'rockchip,grf' property\n"); 1274 return PTR_ERR(grf); 1275 } 1276 1277 if (bus_nr < 0) { 1278 dev_err(&pdev->dev, "rk3x-i2c needs i2cX alias"); 1279 return -EINVAL; 1280 } 1281 1282 /* 27+i: write mask, 11+i: value */ 1283 value = BIT(27 + bus_nr) | BIT(11 + bus_nr); 1284 1285 ret = regmap_write(grf, i2c->soc_data->grf_offset, value); 1286 if (ret != 0) { 1287 dev_err(i2c->dev, "Could not write to GRF: %d\n", ret); 1288 return ret; 1289 } 1290 } 1291 1292 /* IRQ setup */ 1293 irq = platform_get_irq(pdev, 0); 1294 if (irq < 0) 1295 return irq; 1296 1297 ret = devm_request_irq(&pdev->dev, irq, rk3x_i2c_irq, 1298 0, dev_name(&pdev->dev), i2c); 1299 if (ret < 0) { 1300 dev_err(&pdev->dev, "cannot request IRQ\n"); 1301 return ret; 1302 } 1303 1304 platform_set_drvdata(pdev, i2c); 1305 1306 if (i2c->soc_data->calc_timings == rk3x_i2c_v0_calc_timings) { 1307 /* Only one clock to use for bus clock and peripheral clock */ 1308 i2c->clk = devm_clk_get(&pdev->dev, NULL); 1309 i2c->pclk = i2c->clk; 1310 } else { 1311 i2c->clk = devm_clk_get(&pdev->dev, "i2c"); 1312 i2c->pclk = devm_clk_get(&pdev->dev, "pclk"); 1313 } 1314 1315 if (IS_ERR(i2c->clk)) { 1316 ret = PTR_ERR(i2c->clk); 1317 if (ret != -EPROBE_DEFER) 1318 dev_err(&pdev->dev, "Can't get bus clk: %d\n", ret); 1319 return ret; 1320 } 1321 if (IS_ERR(i2c->pclk)) { 1322 ret = PTR_ERR(i2c->pclk); 1323 if (ret != -EPROBE_DEFER) 1324 dev_err(&pdev->dev, "Can't get periph clk: %d\n", ret); 1325 return ret; 1326 } 1327 1328 ret = clk_prepare(i2c->clk); 1329 if (ret < 0) { 1330 dev_err(&pdev->dev, "Can't prepare bus clk: %d\n", ret); 1331 return ret; 1332 } 1333 ret = clk_prepare(i2c->pclk); 1334 if (ret < 0) { 1335 dev_err(&pdev->dev, "Can't prepare periph clock: %d\n", ret); 1336 goto err_clk; 1337 } 1338 1339 i2c->clk_rate_nb.notifier_call = rk3x_i2c_clk_notifier_cb; 1340 ret = clk_notifier_register(i2c->clk, &i2c->clk_rate_nb); 1341 if (ret != 0) { 1342 dev_err(&pdev->dev, "Unable to register clock notifier\n"); 1343 goto err_pclk; 1344 } 1345 1346 clk_rate = clk_get_rate(i2c->clk); 1347 rk3x_i2c_adapt_div(i2c, clk_rate); 1348 1349 ret = i2c_add_adapter(&i2c->adap); 1350 if (ret < 0) 1351 goto err_clk_notifier; 1352 1353 return 0; 1354 1355 err_clk_notifier: 1356 clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb); 1357 err_pclk: 1358 clk_unprepare(i2c->pclk); 1359 err_clk: 1360 clk_unprepare(i2c->clk); 1361 return ret; 1362 } 1363 1364 static int rk3x_i2c_remove(struct platform_device *pdev) 1365 { 1366 struct rk3x_i2c *i2c = platform_get_drvdata(pdev); 1367 1368 i2c_del_adapter(&i2c->adap); 1369 1370 clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb); 1371 clk_unprepare(i2c->pclk); 1372 clk_unprepare(i2c->clk); 1373 1374 return 0; 1375 } 1376 1377 static SIMPLE_DEV_PM_OPS(rk3x_i2c_pm_ops, NULL, rk3x_i2c_resume); 1378 1379 static struct platform_driver rk3x_i2c_driver = { 1380 .probe = rk3x_i2c_probe, 1381 .remove = rk3x_i2c_remove, 1382 .driver = { 1383 .name = "rk3x-i2c", 1384 .of_match_table = rk3x_i2c_match, 1385 .pm = &rk3x_i2c_pm_ops, 1386 }, 1387 }; 1388 1389 module_platform_driver(rk3x_i2c_driver); 1390 1391 MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver"); 1392 MODULE_AUTHOR("Max Schwarz <max.schwarz@online.de>"); 1393 MODULE_LICENSE("GPL v2"); 1394