1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Driver for I2C adapter in Rockchip RK3xxx SoC 4 * 5 * Max Schwarz <max.schwarz@online.de> 6 * based on the patches by Rockchip Inc. 7 */ 8 9 #include <linux/kernel.h> 10 #include <linux/module.h> 11 #include <linux/i2c.h> 12 #include <linux/interrupt.h> 13 #include <linux/errno.h> 14 #include <linux/err.h> 15 #include <linux/platform_device.h> 16 #include <linux/io.h> 17 #include <linux/of_address.h> 18 #include <linux/of_irq.h> 19 #include <linux/spinlock.h> 20 #include <linux/clk.h> 21 #include <linux/wait.h> 22 #include <linux/mfd/syscon.h> 23 #include <linux/regmap.h> 24 #include <linux/math64.h> 25 26 27 /* Register Map */ 28 #define REG_CON 0x00 /* control register */ 29 #define REG_CLKDIV 0x04 /* clock divisor register */ 30 #define REG_MRXADDR 0x08 /* slave address for REGISTER_TX */ 31 #define REG_MRXRADDR 0x0c /* slave register address for REGISTER_TX */ 32 #define REG_MTXCNT 0x10 /* number of bytes to be transmitted */ 33 #define REG_MRXCNT 0x14 /* number of bytes to be received */ 34 #define REG_IEN 0x18 /* interrupt enable */ 35 #define REG_IPD 0x1c /* interrupt pending */ 36 #define REG_FCNT 0x20 /* finished count */ 37 38 /* Data buffer offsets */ 39 #define TXBUFFER_BASE 0x100 40 #define RXBUFFER_BASE 0x200 41 42 /* REG_CON bits */ 43 #define REG_CON_EN BIT(0) 44 enum { 45 REG_CON_MOD_TX = 0, /* transmit data */ 46 REG_CON_MOD_REGISTER_TX, /* select register and restart */ 47 REG_CON_MOD_RX, /* receive data */ 48 REG_CON_MOD_REGISTER_RX, /* broken: transmits read addr AND writes 49 * register addr */ 50 }; 51 #define REG_CON_MOD(mod) ((mod) << 1) 52 #define REG_CON_MOD_MASK (BIT(1) | BIT(2)) 53 #define REG_CON_START BIT(3) 54 #define REG_CON_STOP BIT(4) 55 #define REG_CON_LASTACK BIT(5) /* 1: send NACK after last received byte */ 56 #define REG_CON_ACTACK BIT(6) /* 1: stop if NACK is received */ 57 58 #define REG_CON_TUNING_MASK GENMASK_ULL(15, 8) 59 60 #define REG_CON_SDA_CFG(cfg) ((cfg) << 8) 61 #define REG_CON_STA_CFG(cfg) ((cfg) << 12) 62 #define REG_CON_STO_CFG(cfg) ((cfg) << 14) 63 64 /* REG_MRXADDR bits */ 65 #define REG_MRXADDR_VALID(x) BIT(24 + (x)) /* [x*8+7:x*8] of MRX[R]ADDR valid */ 66 67 /* REG_IEN/REG_IPD bits */ 68 #define REG_INT_BTF BIT(0) /* a byte was transmitted */ 69 #define REG_INT_BRF BIT(1) /* a byte was received */ 70 #define REG_INT_MBTF BIT(2) /* master data transmit finished */ 71 #define REG_INT_MBRF BIT(3) /* master data receive finished */ 72 #define REG_INT_START BIT(4) /* START condition generated */ 73 #define REG_INT_STOP BIT(5) /* STOP condition generated */ 74 #define REG_INT_NAKRCV BIT(6) /* NACK received */ 75 #define REG_INT_ALL 0x7f 76 77 /* Constants */ 78 #define WAIT_TIMEOUT 1000 /* ms */ 79 #define DEFAULT_SCL_RATE (100 * 1000) /* Hz */ 80 81 /** 82 * struct i2c_spec_values: 83 * @min_hold_start_ns: min hold time (repeated) START condition 84 * @min_low_ns: min LOW period of the SCL clock 85 * @min_high_ns: min HIGH period of the SCL cloc 86 * @min_setup_start_ns: min set-up time for a repeated START conditio 87 * @max_data_hold_ns: max data hold time 88 * @min_data_setup_ns: min data set-up time 89 * @min_setup_stop_ns: min set-up time for STOP condition 90 * @min_hold_buffer_ns: min bus free time between a STOP and 91 * START condition 92 */ 93 struct i2c_spec_values { 94 unsigned long min_hold_start_ns; 95 unsigned long min_low_ns; 96 unsigned long min_high_ns; 97 unsigned long min_setup_start_ns; 98 unsigned long max_data_hold_ns; 99 unsigned long min_data_setup_ns; 100 unsigned long min_setup_stop_ns; 101 unsigned long min_hold_buffer_ns; 102 }; 103 104 static const struct i2c_spec_values standard_mode_spec = { 105 .min_hold_start_ns = 4000, 106 .min_low_ns = 4700, 107 .min_high_ns = 4000, 108 .min_setup_start_ns = 4700, 109 .max_data_hold_ns = 3450, 110 .min_data_setup_ns = 250, 111 .min_setup_stop_ns = 4000, 112 .min_hold_buffer_ns = 4700, 113 }; 114 115 static const struct i2c_spec_values fast_mode_spec = { 116 .min_hold_start_ns = 600, 117 .min_low_ns = 1300, 118 .min_high_ns = 600, 119 .min_setup_start_ns = 600, 120 .max_data_hold_ns = 900, 121 .min_data_setup_ns = 100, 122 .min_setup_stop_ns = 600, 123 .min_hold_buffer_ns = 1300, 124 }; 125 126 static const struct i2c_spec_values fast_mode_plus_spec = { 127 .min_hold_start_ns = 260, 128 .min_low_ns = 500, 129 .min_high_ns = 260, 130 .min_setup_start_ns = 260, 131 .max_data_hold_ns = 400, 132 .min_data_setup_ns = 50, 133 .min_setup_stop_ns = 260, 134 .min_hold_buffer_ns = 500, 135 }; 136 137 /** 138 * struct rk3x_i2c_calced_timings: 139 * @div_low: Divider output for low 140 * @div_high: Divider output for high 141 * @tuning: Used to adjust setup/hold data time, 142 * setup/hold start time and setup stop time for 143 * v1's calc_timings, the tuning should all be 0 144 * for old hardware anyone using v0's calc_timings. 145 */ 146 struct rk3x_i2c_calced_timings { 147 unsigned long div_low; 148 unsigned long div_high; 149 unsigned int tuning; 150 }; 151 152 enum rk3x_i2c_state { 153 STATE_IDLE, 154 STATE_START, 155 STATE_READ, 156 STATE_WRITE, 157 STATE_STOP 158 }; 159 160 /** 161 * struct rk3x_i2c_soc_data: 162 * @grf_offset: offset inside the grf regmap for setting the i2c type 163 * @calc_timings: Callback function for i2c timing information calculated 164 */ 165 struct rk3x_i2c_soc_data { 166 int grf_offset; 167 int (*calc_timings)(unsigned long, struct i2c_timings *, 168 struct rk3x_i2c_calced_timings *); 169 }; 170 171 /** 172 * struct rk3x_i2c - private data of the controller 173 * @adap: corresponding I2C adapter 174 * @dev: device for this controller 175 * @soc_data: related soc data struct 176 * @regs: virtual memory area 177 * @clk: function clk for rk3399 or function & Bus clks for others 178 * @pclk: Bus clk for rk3399 179 * @clk_rate_nb: i2c clk rate change notify 180 * @t: I2C known timing information 181 * @lock: spinlock for the i2c bus 182 * @wait: the waitqueue to wait for i2c transfer 183 * @busy: the condition for the event to wait for 184 * @msg: current i2c message 185 * @addr: addr of i2c slave device 186 * @mode: mode of i2c transfer 187 * @is_last_msg: flag determines whether it is the last msg in this transfer 188 * @state: state of i2c transfer 189 * @processed: byte length which has been send or received 190 * @error: error code for i2c transfer 191 */ 192 struct rk3x_i2c { 193 struct i2c_adapter adap; 194 struct device *dev; 195 const struct rk3x_i2c_soc_data *soc_data; 196 197 /* Hardware resources */ 198 void __iomem *regs; 199 struct clk *clk; 200 struct clk *pclk; 201 struct notifier_block clk_rate_nb; 202 203 /* Settings */ 204 struct i2c_timings t; 205 206 /* Synchronization & notification */ 207 spinlock_t lock; 208 wait_queue_head_t wait; 209 bool busy; 210 211 /* Current message */ 212 struct i2c_msg *msg; 213 u8 addr; 214 unsigned int mode; 215 bool is_last_msg; 216 217 /* I2C state machine */ 218 enum rk3x_i2c_state state; 219 unsigned int processed; 220 int error; 221 }; 222 223 static inline void i2c_writel(struct rk3x_i2c *i2c, u32 value, 224 unsigned int offset) 225 { 226 writel(value, i2c->regs + offset); 227 } 228 229 static inline u32 i2c_readl(struct rk3x_i2c *i2c, unsigned int offset) 230 { 231 return readl(i2c->regs + offset); 232 } 233 234 /* Reset all interrupt pending bits */ 235 static inline void rk3x_i2c_clean_ipd(struct rk3x_i2c *i2c) 236 { 237 i2c_writel(i2c, REG_INT_ALL, REG_IPD); 238 } 239 240 /** 241 * Generate a START condition, which triggers a REG_INT_START interrupt. 242 */ 243 static void rk3x_i2c_start(struct rk3x_i2c *i2c) 244 { 245 u32 val = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 246 247 i2c_writel(i2c, REG_INT_START, REG_IEN); 248 249 /* enable adapter with correct mode, send START condition */ 250 val |= REG_CON_EN | REG_CON_MOD(i2c->mode) | REG_CON_START; 251 252 /* if we want to react to NACK, set ACTACK bit */ 253 if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) 254 val |= REG_CON_ACTACK; 255 256 i2c_writel(i2c, val, REG_CON); 257 } 258 259 /** 260 * Generate a STOP condition, which triggers a REG_INT_STOP interrupt. 261 * 262 * @error: Error code to return in rk3x_i2c_xfer 263 */ 264 static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error) 265 { 266 unsigned int ctrl; 267 268 i2c->processed = 0; 269 i2c->msg = NULL; 270 i2c->error = error; 271 272 if (i2c->is_last_msg) { 273 /* Enable stop interrupt */ 274 i2c_writel(i2c, REG_INT_STOP, REG_IEN); 275 276 i2c->state = STATE_STOP; 277 278 ctrl = i2c_readl(i2c, REG_CON); 279 ctrl |= REG_CON_STOP; 280 i2c_writel(i2c, ctrl, REG_CON); 281 } else { 282 /* Signal rk3x_i2c_xfer to start the next message. */ 283 i2c->busy = false; 284 i2c->state = STATE_IDLE; 285 286 /* 287 * The HW is actually not capable of REPEATED START. But we can 288 * get the intended effect by resetting its internal state 289 * and issuing an ordinary START. 290 */ 291 ctrl = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 292 i2c_writel(i2c, ctrl, REG_CON); 293 294 /* signal that we are finished with the current msg */ 295 wake_up(&i2c->wait); 296 } 297 } 298 299 /** 300 * Setup a read according to i2c->msg 301 */ 302 static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c) 303 { 304 unsigned int len = i2c->msg->len - i2c->processed; 305 u32 con; 306 307 con = i2c_readl(i2c, REG_CON); 308 309 /* 310 * The hw can read up to 32 bytes at a time. If we need more than one 311 * chunk, send an ACK after the last byte of the current chunk. 312 */ 313 if (len > 32) { 314 len = 32; 315 con &= ~REG_CON_LASTACK; 316 } else { 317 con |= REG_CON_LASTACK; 318 } 319 320 /* make sure we are in plain RX mode if we read a second chunk */ 321 if (i2c->processed != 0) { 322 con &= ~REG_CON_MOD_MASK; 323 con |= REG_CON_MOD(REG_CON_MOD_RX); 324 } 325 326 i2c_writel(i2c, con, REG_CON); 327 i2c_writel(i2c, len, REG_MRXCNT); 328 } 329 330 /** 331 * Fill the transmit buffer with data from i2c->msg 332 */ 333 static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c) 334 { 335 unsigned int i, j; 336 u32 cnt = 0; 337 u32 val; 338 u8 byte; 339 340 for (i = 0; i < 8; ++i) { 341 val = 0; 342 for (j = 0; j < 4; ++j) { 343 if ((i2c->processed == i2c->msg->len) && (cnt != 0)) 344 break; 345 346 if (i2c->processed == 0 && cnt == 0) 347 byte = (i2c->addr & 0x7f) << 1; 348 else 349 byte = i2c->msg->buf[i2c->processed++]; 350 351 val |= byte << (j * 8); 352 cnt++; 353 } 354 355 i2c_writel(i2c, val, TXBUFFER_BASE + 4 * i); 356 357 if (i2c->processed == i2c->msg->len) 358 break; 359 } 360 361 i2c_writel(i2c, cnt, REG_MTXCNT); 362 } 363 364 365 /* IRQ handlers for individual states */ 366 367 static void rk3x_i2c_handle_start(struct rk3x_i2c *i2c, unsigned int ipd) 368 { 369 if (!(ipd & REG_INT_START)) { 370 rk3x_i2c_stop(i2c, -EIO); 371 dev_warn(i2c->dev, "unexpected irq in START: 0x%x\n", ipd); 372 rk3x_i2c_clean_ipd(i2c); 373 return; 374 } 375 376 /* ack interrupt */ 377 i2c_writel(i2c, REG_INT_START, REG_IPD); 378 379 /* disable start bit */ 380 i2c_writel(i2c, i2c_readl(i2c, REG_CON) & ~REG_CON_START, REG_CON); 381 382 /* enable appropriate interrupts and transition */ 383 if (i2c->mode == REG_CON_MOD_TX) { 384 i2c_writel(i2c, REG_INT_MBTF | REG_INT_NAKRCV, REG_IEN); 385 i2c->state = STATE_WRITE; 386 rk3x_i2c_fill_transmit_buf(i2c); 387 } else { 388 /* in any other case, we are going to be reading. */ 389 i2c_writel(i2c, REG_INT_MBRF | REG_INT_NAKRCV, REG_IEN); 390 i2c->state = STATE_READ; 391 rk3x_i2c_prepare_read(i2c); 392 } 393 } 394 395 static void rk3x_i2c_handle_write(struct rk3x_i2c *i2c, unsigned int ipd) 396 { 397 if (!(ipd & REG_INT_MBTF)) { 398 rk3x_i2c_stop(i2c, -EIO); 399 dev_err(i2c->dev, "unexpected irq in WRITE: 0x%x\n", ipd); 400 rk3x_i2c_clean_ipd(i2c); 401 return; 402 } 403 404 /* ack interrupt */ 405 i2c_writel(i2c, REG_INT_MBTF, REG_IPD); 406 407 /* are we finished? */ 408 if (i2c->processed == i2c->msg->len) 409 rk3x_i2c_stop(i2c, i2c->error); 410 else 411 rk3x_i2c_fill_transmit_buf(i2c); 412 } 413 414 static void rk3x_i2c_handle_read(struct rk3x_i2c *i2c, unsigned int ipd) 415 { 416 unsigned int i; 417 unsigned int len = i2c->msg->len - i2c->processed; 418 u32 uninitialized_var(val); 419 u8 byte; 420 421 /* we only care for MBRF here. */ 422 if (!(ipd & REG_INT_MBRF)) 423 return; 424 425 /* ack interrupt */ 426 i2c_writel(i2c, REG_INT_MBRF, REG_IPD); 427 428 /* Can only handle a maximum of 32 bytes at a time */ 429 if (len > 32) 430 len = 32; 431 432 /* read the data from receive buffer */ 433 for (i = 0; i < len; ++i) { 434 if (i % 4 == 0) 435 val = i2c_readl(i2c, RXBUFFER_BASE + (i / 4) * 4); 436 437 byte = (val >> ((i % 4) * 8)) & 0xff; 438 i2c->msg->buf[i2c->processed++] = byte; 439 } 440 441 /* are we finished? */ 442 if (i2c->processed == i2c->msg->len) 443 rk3x_i2c_stop(i2c, i2c->error); 444 else 445 rk3x_i2c_prepare_read(i2c); 446 } 447 448 static void rk3x_i2c_handle_stop(struct rk3x_i2c *i2c, unsigned int ipd) 449 { 450 unsigned int con; 451 452 if (!(ipd & REG_INT_STOP)) { 453 rk3x_i2c_stop(i2c, -EIO); 454 dev_err(i2c->dev, "unexpected irq in STOP: 0x%x\n", ipd); 455 rk3x_i2c_clean_ipd(i2c); 456 return; 457 } 458 459 /* ack interrupt */ 460 i2c_writel(i2c, REG_INT_STOP, REG_IPD); 461 462 /* disable STOP bit */ 463 con = i2c_readl(i2c, REG_CON); 464 con &= ~REG_CON_STOP; 465 i2c_writel(i2c, con, REG_CON); 466 467 i2c->busy = false; 468 i2c->state = STATE_IDLE; 469 470 /* signal rk3x_i2c_xfer that we are finished */ 471 wake_up(&i2c->wait); 472 } 473 474 static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id) 475 { 476 struct rk3x_i2c *i2c = dev_id; 477 unsigned int ipd; 478 479 spin_lock(&i2c->lock); 480 481 ipd = i2c_readl(i2c, REG_IPD); 482 if (i2c->state == STATE_IDLE) { 483 dev_warn(i2c->dev, "irq in STATE_IDLE, ipd = 0x%x\n", ipd); 484 rk3x_i2c_clean_ipd(i2c); 485 goto out; 486 } 487 488 dev_dbg(i2c->dev, "IRQ: state %d, ipd: %x\n", i2c->state, ipd); 489 490 /* Clean interrupt bits we don't care about */ 491 ipd &= ~(REG_INT_BRF | REG_INT_BTF); 492 493 if (ipd & REG_INT_NAKRCV) { 494 /* 495 * We got a NACK in the last operation. Depending on whether 496 * IGNORE_NAK is set, we have to stop the operation and report 497 * an error. 498 */ 499 i2c_writel(i2c, REG_INT_NAKRCV, REG_IPD); 500 501 ipd &= ~REG_INT_NAKRCV; 502 503 if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) 504 rk3x_i2c_stop(i2c, -ENXIO); 505 } 506 507 /* is there anything left to handle? */ 508 if ((ipd & REG_INT_ALL) == 0) 509 goto out; 510 511 switch (i2c->state) { 512 case STATE_START: 513 rk3x_i2c_handle_start(i2c, ipd); 514 break; 515 case STATE_WRITE: 516 rk3x_i2c_handle_write(i2c, ipd); 517 break; 518 case STATE_READ: 519 rk3x_i2c_handle_read(i2c, ipd); 520 break; 521 case STATE_STOP: 522 rk3x_i2c_handle_stop(i2c, ipd); 523 break; 524 case STATE_IDLE: 525 break; 526 } 527 528 out: 529 spin_unlock(&i2c->lock); 530 return IRQ_HANDLED; 531 } 532 533 /** 534 * Get timing values of I2C specification 535 * 536 * @speed: Desired SCL frequency 537 * 538 * Returns: Matched i2c spec values. 539 */ 540 static const struct i2c_spec_values *rk3x_i2c_get_spec(unsigned int speed) 541 { 542 if (speed <= I2C_MAX_STANDARD_MODE_FREQ) 543 return &standard_mode_spec; 544 else if (speed <= I2C_MAX_FAST_MODE_FREQ) 545 return &fast_mode_spec; 546 else 547 return &fast_mode_plus_spec; 548 } 549 550 /** 551 * Calculate divider values for desired SCL frequency 552 * 553 * @clk_rate: I2C input clock rate 554 * @t: Known I2C timing information 555 * @t_calc: Caculated rk3x private timings that would be written into regs 556 * 557 * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case 558 * a best-effort divider value is returned in divs. If the target rate is 559 * too high, we silently use the highest possible rate. 560 */ 561 static int rk3x_i2c_v0_calc_timings(unsigned long clk_rate, 562 struct i2c_timings *t, 563 struct rk3x_i2c_calced_timings *t_calc) 564 { 565 unsigned long min_low_ns, min_high_ns; 566 unsigned long max_low_ns, min_total_ns; 567 568 unsigned long clk_rate_khz, scl_rate_khz; 569 570 unsigned long min_low_div, min_high_div; 571 unsigned long max_low_div; 572 573 unsigned long min_div_for_hold, min_total_div; 574 unsigned long extra_div, extra_low_div, ideal_low_div; 575 576 unsigned long data_hold_buffer_ns = 50; 577 const struct i2c_spec_values *spec; 578 int ret = 0; 579 580 /* Only support standard-mode and fast-mode */ 581 if (WARN_ON(t->bus_freq_hz > I2C_MAX_FAST_MODE_FREQ)) 582 t->bus_freq_hz = I2C_MAX_FAST_MODE_FREQ; 583 584 /* prevent scl_rate_khz from becoming 0 */ 585 if (WARN_ON(t->bus_freq_hz < 1000)) 586 t->bus_freq_hz = 1000; 587 588 /* 589 * min_low_ns: The minimum number of ns we need to hold low to 590 * meet I2C specification, should include fall time. 591 * min_high_ns: The minimum number of ns we need to hold high to 592 * meet I2C specification, should include rise time. 593 * max_low_ns: The maximum number of ns we can hold low to meet 594 * I2C specification. 595 * 596 * Note: max_low_ns should be (maximum data hold time * 2 - buffer) 597 * This is because the i2c host on Rockchip holds the data line 598 * for half the low time. 599 */ 600 spec = rk3x_i2c_get_spec(t->bus_freq_hz); 601 min_high_ns = t->scl_rise_ns + spec->min_high_ns; 602 603 /* 604 * Timings for repeated start: 605 * - controller appears to drop SDA at .875x (7/8) programmed clk high. 606 * - controller appears to keep SCL high for 2x programmed clk high. 607 * 608 * We need to account for those rules in picking our "high" time so 609 * we meet tSU;STA and tHD;STA times. 610 */ 611 min_high_ns = max(min_high_ns, DIV_ROUND_UP( 612 (t->scl_rise_ns + spec->min_setup_start_ns) * 1000, 875)); 613 min_high_ns = max(min_high_ns, DIV_ROUND_UP( 614 (t->scl_rise_ns + spec->min_setup_start_ns + t->sda_fall_ns + 615 spec->min_high_ns), 2)); 616 617 min_low_ns = t->scl_fall_ns + spec->min_low_ns; 618 max_low_ns = spec->max_data_hold_ns * 2 - data_hold_buffer_ns; 619 min_total_ns = min_low_ns + min_high_ns; 620 621 /* Adjust to avoid overflow */ 622 clk_rate_khz = DIV_ROUND_UP(clk_rate, 1000); 623 scl_rate_khz = t->bus_freq_hz / 1000; 624 625 /* 626 * We need the total div to be >= this number 627 * so we don't clock too fast. 628 */ 629 min_total_div = DIV_ROUND_UP(clk_rate_khz, scl_rate_khz * 8); 630 631 /* These are the min dividers needed for min hold times. */ 632 min_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 8 * 1000000); 633 min_high_div = DIV_ROUND_UP(clk_rate_khz * min_high_ns, 8 * 1000000); 634 min_div_for_hold = (min_low_div + min_high_div); 635 636 /* 637 * This is the maximum divider so we don't go over the maximum. 638 * We don't round up here (we round down) since this is a maximum. 639 */ 640 max_low_div = clk_rate_khz * max_low_ns / (8 * 1000000); 641 642 if (min_low_div > max_low_div) { 643 WARN_ONCE(true, 644 "Conflicting, min_low_div %lu, max_low_div %lu\n", 645 min_low_div, max_low_div); 646 max_low_div = min_low_div; 647 } 648 649 if (min_div_for_hold > min_total_div) { 650 /* 651 * Time needed to meet hold requirements is important. 652 * Just use that. 653 */ 654 t_calc->div_low = min_low_div; 655 t_calc->div_high = min_high_div; 656 } else { 657 /* 658 * We've got to distribute some time among the low and high 659 * so we don't run too fast. 660 */ 661 extra_div = min_total_div - min_div_for_hold; 662 663 /* 664 * We'll try to split things up perfectly evenly, 665 * biasing slightly towards having a higher div 666 * for low (spend more time low). 667 */ 668 ideal_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 669 scl_rate_khz * 8 * min_total_ns); 670 671 /* Don't allow it to go over the maximum */ 672 if (ideal_low_div > max_low_div) 673 ideal_low_div = max_low_div; 674 675 /* 676 * Handle when the ideal low div is going to take up 677 * more than we have. 678 */ 679 if (ideal_low_div > min_low_div + extra_div) 680 ideal_low_div = min_low_div + extra_div; 681 682 /* Give low the "ideal" and give high whatever extra is left */ 683 extra_low_div = ideal_low_div - min_low_div; 684 t_calc->div_low = ideal_low_div; 685 t_calc->div_high = min_high_div + (extra_div - extra_low_div); 686 } 687 688 /* 689 * Adjust to the fact that the hardware has an implicit "+1". 690 * NOTE: Above calculations always produce div_low > 0 and div_high > 0. 691 */ 692 t_calc->div_low--; 693 t_calc->div_high--; 694 695 /* Give the tuning value 0, that would not update con register */ 696 t_calc->tuning = 0; 697 /* Maximum divider supported by hw is 0xffff */ 698 if (t_calc->div_low > 0xffff) { 699 t_calc->div_low = 0xffff; 700 ret = -EINVAL; 701 } 702 703 if (t_calc->div_high > 0xffff) { 704 t_calc->div_high = 0xffff; 705 ret = -EINVAL; 706 } 707 708 return ret; 709 } 710 711 /** 712 * Calculate timing values for desired SCL frequency 713 * 714 * @clk_rate: I2C input clock rate 715 * @t: Known I2C timing information 716 * @t_calc: Caculated rk3x private timings that would be written into regs 717 * 718 * Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case 719 * a best-effort divider value is returned in divs. If the target rate is 720 * too high, we silently use the highest possible rate. 721 * The following formulas are v1's method to calculate timings. 722 * 723 * l = divl + 1; 724 * h = divh + 1; 725 * s = sda_update_config + 1; 726 * u = start_setup_config + 1; 727 * p = stop_setup_config + 1; 728 * T = Tclk_i2c; 729 * 730 * tHigh = 8 * h * T; 731 * tLow = 8 * l * T; 732 * 733 * tHD;sda = (l * s + 1) * T; 734 * tSU;sda = [(8 - s) * l + 1] * T; 735 * tI2C = 8 * (l + h) * T; 736 * 737 * tSU;sta = (8h * u + 1) * T; 738 * tHD;sta = [8h * (u + 1) - 1] * T; 739 * tSU;sto = (8h * p + 1) * T; 740 */ 741 static int rk3x_i2c_v1_calc_timings(unsigned long clk_rate, 742 struct i2c_timings *t, 743 struct rk3x_i2c_calced_timings *t_calc) 744 { 745 unsigned long min_low_ns, min_high_ns; 746 unsigned long min_setup_start_ns, min_setup_data_ns; 747 unsigned long min_setup_stop_ns, max_hold_data_ns; 748 749 unsigned long clk_rate_khz, scl_rate_khz; 750 751 unsigned long min_low_div, min_high_div; 752 753 unsigned long min_div_for_hold, min_total_div; 754 unsigned long extra_div, extra_low_div; 755 unsigned long sda_update_cfg, stp_sta_cfg, stp_sto_cfg; 756 757 const struct i2c_spec_values *spec; 758 int ret = 0; 759 760 /* Support standard-mode, fast-mode and fast-mode plus */ 761 if (WARN_ON(t->bus_freq_hz > I2C_MAX_FAST_MODE_PLUS_FREQ)) 762 t->bus_freq_hz = I2C_MAX_FAST_MODE_PLUS_FREQ; 763 764 /* prevent scl_rate_khz from becoming 0 */ 765 if (WARN_ON(t->bus_freq_hz < 1000)) 766 t->bus_freq_hz = 1000; 767 768 /* 769 * min_low_ns: The minimum number of ns we need to hold low to 770 * meet I2C specification, should include fall time. 771 * min_high_ns: The minimum number of ns we need to hold high to 772 * meet I2C specification, should include rise time. 773 */ 774 spec = rk3x_i2c_get_spec(t->bus_freq_hz); 775 776 /* calculate min-divh and min-divl */ 777 clk_rate_khz = DIV_ROUND_UP(clk_rate, 1000); 778 scl_rate_khz = t->bus_freq_hz / 1000; 779 min_total_div = DIV_ROUND_UP(clk_rate_khz, scl_rate_khz * 8); 780 781 min_high_ns = t->scl_rise_ns + spec->min_high_ns; 782 min_high_div = DIV_ROUND_UP(clk_rate_khz * min_high_ns, 8 * 1000000); 783 784 min_low_ns = t->scl_fall_ns + spec->min_low_ns; 785 min_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 8 * 1000000); 786 787 /* 788 * Final divh and divl must be greater than 0, otherwise the 789 * hardware would not output the i2c clk. 790 */ 791 min_high_div = (min_high_div < 1) ? 2 : min_high_div; 792 min_low_div = (min_low_div < 1) ? 2 : min_low_div; 793 794 /* These are the min dividers needed for min hold times. */ 795 min_div_for_hold = (min_low_div + min_high_div); 796 797 /* 798 * This is the maximum divider so we don't go over the maximum. 799 * We don't round up here (we round down) since this is a maximum. 800 */ 801 if (min_div_for_hold >= min_total_div) { 802 /* 803 * Time needed to meet hold requirements is important. 804 * Just use that. 805 */ 806 t_calc->div_low = min_low_div; 807 t_calc->div_high = min_high_div; 808 } else { 809 /* 810 * We've got to distribute some time among the low and high 811 * so we don't run too fast. 812 * We'll try to split things up by the scale of min_low_div and 813 * min_high_div, biasing slightly towards having a higher div 814 * for low (spend more time low). 815 */ 816 extra_div = min_total_div - min_div_for_hold; 817 extra_low_div = DIV_ROUND_UP(min_low_div * extra_div, 818 min_div_for_hold); 819 820 t_calc->div_low = min_low_div + extra_low_div; 821 t_calc->div_high = min_high_div + (extra_div - extra_low_div); 822 } 823 824 /* 825 * calculate sda data hold count by the rules, data_upd_st:3 826 * is a appropriate value to reduce calculated times. 827 */ 828 for (sda_update_cfg = 3; sda_update_cfg > 0; sda_update_cfg--) { 829 max_hold_data_ns = DIV_ROUND_UP((sda_update_cfg 830 * (t_calc->div_low) + 1) 831 * 1000000, clk_rate_khz); 832 min_setup_data_ns = DIV_ROUND_UP(((8 - sda_update_cfg) 833 * (t_calc->div_low) + 1) 834 * 1000000, clk_rate_khz); 835 if ((max_hold_data_ns < spec->max_data_hold_ns) && 836 (min_setup_data_ns > spec->min_data_setup_ns)) 837 break; 838 } 839 840 /* calculate setup start config */ 841 min_setup_start_ns = t->scl_rise_ns + spec->min_setup_start_ns; 842 stp_sta_cfg = DIV_ROUND_UP(clk_rate_khz * min_setup_start_ns 843 - 1000000, 8 * 1000000 * (t_calc->div_high)); 844 845 /* calculate setup stop config */ 846 min_setup_stop_ns = t->scl_rise_ns + spec->min_setup_stop_ns; 847 stp_sto_cfg = DIV_ROUND_UP(clk_rate_khz * min_setup_stop_ns 848 - 1000000, 8 * 1000000 * (t_calc->div_high)); 849 850 t_calc->tuning = REG_CON_SDA_CFG(--sda_update_cfg) | 851 REG_CON_STA_CFG(--stp_sta_cfg) | 852 REG_CON_STO_CFG(--stp_sto_cfg); 853 854 t_calc->div_low--; 855 t_calc->div_high--; 856 857 /* Maximum divider supported by hw is 0xffff */ 858 if (t_calc->div_low > 0xffff) { 859 t_calc->div_low = 0xffff; 860 ret = -EINVAL; 861 } 862 863 if (t_calc->div_high > 0xffff) { 864 t_calc->div_high = 0xffff; 865 ret = -EINVAL; 866 } 867 868 return ret; 869 } 870 871 static void rk3x_i2c_adapt_div(struct rk3x_i2c *i2c, unsigned long clk_rate) 872 { 873 struct i2c_timings *t = &i2c->t; 874 struct rk3x_i2c_calced_timings calc; 875 u64 t_low_ns, t_high_ns; 876 unsigned long flags; 877 u32 val; 878 int ret; 879 880 ret = i2c->soc_data->calc_timings(clk_rate, t, &calc); 881 WARN_ONCE(ret != 0, "Could not reach SCL freq %u", t->bus_freq_hz); 882 883 clk_enable(i2c->pclk); 884 885 spin_lock_irqsave(&i2c->lock, flags); 886 val = i2c_readl(i2c, REG_CON); 887 val &= ~REG_CON_TUNING_MASK; 888 val |= calc.tuning; 889 i2c_writel(i2c, val, REG_CON); 890 i2c_writel(i2c, (calc.div_high << 16) | (calc.div_low & 0xffff), 891 REG_CLKDIV); 892 spin_unlock_irqrestore(&i2c->lock, flags); 893 894 clk_disable(i2c->pclk); 895 896 t_low_ns = div_u64(((u64)calc.div_low + 1) * 8 * 1000000000, clk_rate); 897 t_high_ns = div_u64(((u64)calc.div_high + 1) * 8 * 1000000000, 898 clk_rate); 899 dev_dbg(i2c->dev, 900 "CLK %lukhz, Req %uns, Act low %lluns high %lluns\n", 901 clk_rate / 1000, 902 1000000000 / t->bus_freq_hz, 903 t_low_ns, t_high_ns); 904 } 905 906 /** 907 * rk3x_i2c_clk_notifier_cb - Clock rate change callback 908 * @nb: Pointer to notifier block 909 * @event: Notification reason 910 * @data: Pointer to notification data object 911 * 912 * The callback checks whether a valid bus frequency can be generated after the 913 * change. If so, the change is acknowledged, otherwise the change is aborted. 914 * New dividers are written to the HW in the pre- or post change notification 915 * depending on the scaling direction. 916 * 917 * Code adapted from i2c-cadence.c. 918 * 919 * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK 920 * to acknowledge the change, NOTIFY_DONE if the notification is 921 * considered irrelevant. 922 */ 923 static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long 924 event, void *data) 925 { 926 struct clk_notifier_data *ndata = data; 927 struct rk3x_i2c *i2c = container_of(nb, struct rk3x_i2c, clk_rate_nb); 928 struct rk3x_i2c_calced_timings calc; 929 930 switch (event) { 931 case PRE_RATE_CHANGE: 932 /* 933 * Try the calculation (but don't store the result) ahead of 934 * time to see if we need to block the clock change. Timings 935 * shouldn't actually take effect until rk3x_i2c_adapt_div(). 936 */ 937 if (i2c->soc_data->calc_timings(ndata->new_rate, &i2c->t, 938 &calc) != 0) 939 return NOTIFY_STOP; 940 941 /* scale up */ 942 if (ndata->new_rate > ndata->old_rate) 943 rk3x_i2c_adapt_div(i2c, ndata->new_rate); 944 945 return NOTIFY_OK; 946 case POST_RATE_CHANGE: 947 /* scale down */ 948 if (ndata->new_rate < ndata->old_rate) 949 rk3x_i2c_adapt_div(i2c, ndata->new_rate); 950 return NOTIFY_OK; 951 case ABORT_RATE_CHANGE: 952 /* scale up */ 953 if (ndata->new_rate > ndata->old_rate) 954 rk3x_i2c_adapt_div(i2c, ndata->old_rate); 955 return NOTIFY_OK; 956 default: 957 return NOTIFY_DONE; 958 } 959 } 960 961 /** 962 * Setup I2C registers for an I2C operation specified by msgs, num. 963 * 964 * Must be called with i2c->lock held. 965 * 966 * @msgs: I2C msgs to process 967 * @num: Number of msgs 968 * 969 * returns: Number of I2C msgs processed or negative in case of error 970 */ 971 static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num) 972 { 973 u32 addr = (msgs[0].addr & 0x7f) << 1; 974 int ret = 0; 975 976 /* 977 * The I2C adapter can issue a small (len < 4) write packet before 978 * reading. This speeds up SMBus-style register reads. 979 * The MRXADDR/MRXRADDR hold the slave address and the slave register 980 * address in this case. 981 */ 982 983 if (num >= 2 && msgs[0].len < 4 && 984 !(msgs[0].flags & I2C_M_RD) && (msgs[1].flags & I2C_M_RD)) { 985 u32 reg_addr = 0; 986 int i; 987 988 dev_dbg(i2c->dev, "Combined write/read from addr 0x%x\n", 989 addr >> 1); 990 991 /* Fill MRXRADDR with the register address(es) */ 992 for (i = 0; i < msgs[0].len; ++i) { 993 reg_addr |= msgs[0].buf[i] << (i * 8); 994 reg_addr |= REG_MRXADDR_VALID(i); 995 } 996 997 /* msgs[0] is handled by hw. */ 998 i2c->msg = &msgs[1]; 999 1000 i2c->mode = REG_CON_MOD_REGISTER_TX; 1001 1002 i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), REG_MRXADDR); 1003 i2c_writel(i2c, reg_addr, REG_MRXRADDR); 1004 1005 ret = 2; 1006 } else { 1007 /* 1008 * We'll have to do it the boring way and process the msgs 1009 * one-by-one. 1010 */ 1011 1012 if (msgs[0].flags & I2C_M_RD) { 1013 addr |= 1; /* set read bit */ 1014 1015 /* 1016 * We have to transmit the slave addr first. Use 1017 * MOD_REGISTER_TX for that purpose. 1018 */ 1019 i2c->mode = REG_CON_MOD_REGISTER_TX; 1020 i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), 1021 REG_MRXADDR); 1022 i2c_writel(i2c, 0, REG_MRXRADDR); 1023 } else { 1024 i2c->mode = REG_CON_MOD_TX; 1025 } 1026 1027 i2c->msg = &msgs[0]; 1028 1029 ret = 1; 1030 } 1031 1032 i2c->addr = msgs[0].addr; 1033 i2c->busy = true; 1034 i2c->state = STATE_START; 1035 i2c->processed = 0; 1036 i2c->error = 0; 1037 1038 rk3x_i2c_clean_ipd(i2c); 1039 1040 return ret; 1041 } 1042 1043 static int rk3x_i2c_xfer(struct i2c_adapter *adap, 1044 struct i2c_msg *msgs, int num) 1045 { 1046 struct rk3x_i2c *i2c = (struct rk3x_i2c *)adap->algo_data; 1047 unsigned long timeout, flags; 1048 u32 val; 1049 int ret = 0; 1050 int i; 1051 1052 spin_lock_irqsave(&i2c->lock, flags); 1053 1054 clk_enable(i2c->clk); 1055 clk_enable(i2c->pclk); 1056 1057 i2c->is_last_msg = false; 1058 1059 /* 1060 * Process msgs. We can handle more than one message at once (see 1061 * rk3x_i2c_setup()). 1062 */ 1063 for (i = 0; i < num; i += ret) { 1064 ret = rk3x_i2c_setup(i2c, msgs + i, num - i); 1065 1066 if (ret < 0) { 1067 dev_err(i2c->dev, "rk3x_i2c_setup() failed\n"); 1068 break; 1069 } 1070 1071 if (i + ret >= num) 1072 i2c->is_last_msg = true; 1073 1074 spin_unlock_irqrestore(&i2c->lock, flags); 1075 1076 rk3x_i2c_start(i2c); 1077 1078 timeout = wait_event_timeout(i2c->wait, !i2c->busy, 1079 msecs_to_jiffies(WAIT_TIMEOUT)); 1080 1081 spin_lock_irqsave(&i2c->lock, flags); 1082 1083 if (timeout == 0) { 1084 dev_err(i2c->dev, "timeout, ipd: 0x%02x, state: %d\n", 1085 i2c_readl(i2c, REG_IPD), i2c->state); 1086 1087 /* Force a STOP condition without interrupt */ 1088 i2c_writel(i2c, 0, REG_IEN); 1089 val = i2c_readl(i2c, REG_CON) & REG_CON_TUNING_MASK; 1090 val |= REG_CON_EN | REG_CON_STOP; 1091 i2c_writel(i2c, val, REG_CON); 1092 1093 i2c->state = STATE_IDLE; 1094 1095 ret = -ETIMEDOUT; 1096 break; 1097 } 1098 1099 if (i2c->error) { 1100 ret = i2c->error; 1101 break; 1102 } 1103 } 1104 1105 clk_disable(i2c->pclk); 1106 clk_disable(i2c->clk); 1107 1108 spin_unlock_irqrestore(&i2c->lock, flags); 1109 1110 return ret < 0 ? ret : num; 1111 } 1112 1113 static __maybe_unused int rk3x_i2c_resume(struct device *dev) 1114 { 1115 struct rk3x_i2c *i2c = dev_get_drvdata(dev); 1116 1117 rk3x_i2c_adapt_div(i2c, clk_get_rate(i2c->clk)); 1118 1119 return 0; 1120 } 1121 1122 static u32 rk3x_i2c_func(struct i2c_adapter *adap) 1123 { 1124 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING; 1125 } 1126 1127 static const struct i2c_algorithm rk3x_i2c_algorithm = { 1128 .master_xfer = rk3x_i2c_xfer, 1129 .functionality = rk3x_i2c_func, 1130 }; 1131 1132 static const struct rk3x_i2c_soc_data rv1108_soc_data = { 1133 .grf_offset = -1, 1134 .calc_timings = rk3x_i2c_v1_calc_timings, 1135 }; 1136 1137 static const struct rk3x_i2c_soc_data rk3066_soc_data = { 1138 .grf_offset = 0x154, 1139 .calc_timings = rk3x_i2c_v0_calc_timings, 1140 }; 1141 1142 static const struct rk3x_i2c_soc_data rk3188_soc_data = { 1143 .grf_offset = 0x0a4, 1144 .calc_timings = rk3x_i2c_v0_calc_timings, 1145 }; 1146 1147 static const struct rk3x_i2c_soc_data rk3228_soc_data = { 1148 .grf_offset = -1, 1149 .calc_timings = rk3x_i2c_v0_calc_timings, 1150 }; 1151 1152 static const struct rk3x_i2c_soc_data rk3288_soc_data = { 1153 .grf_offset = -1, 1154 .calc_timings = rk3x_i2c_v0_calc_timings, 1155 }; 1156 1157 static const struct rk3x_i2c_soc_data rk3399_soc_data = { 1158 .grf_offset = -1, 1159 .calc_timings = rk3x_i2c_v1_calc_timings, 1160 }; 1161 1162 static const struct of_device_id rk3x_i2c_match[] = { 1163 { 1164 .compatible = "rockchip,rv1108-i2c", 1165 .data = &rv1108_soc_data 1166 }, 1167 { 1168 .compatible = "rockchip,rk3066-i2c", 1169 .data = &rk3066_soc_data 1170 }, 1171 { 1172 .compatible = "rockchip,rk3188-i2c", 1173 .data = &rk3188_soc_data 1174 }, 1175 { 1176 .compatible = "rockchip,rk3228-i2c", 1177 .data = &rk3228_soc_data 1178 }, 1179 { 1180 .compatible = "rockchip,rk3288-i2c", 1181 .data = &rk3288_soc_data 1182 }, 1183 { 1184 .compatible = "rockchip,rk3399-i2c", 1185 .data = &rk3399_soc_data 1186 }, 1187 {}, 1188 }; 1189 MODULE_DEVICE_TABLE(of, rk3x_i2c_match); 1190 1191 static int rk3x_i2c_probe(struct platform_device *pdev) 1192 { 1193 struct device_node *np = pdev->dev.of_node; 1194 const struct of_device_id *match; 1195 struct rk3x_i2c *i2c; 1196 int ret = 0; 1197 int bus_nr; 1198 u32 value; 1199 int irq; 1200 unsigned long clk_rate; 1201 1202 i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL); 1203 if (!i2c) 1204 return -ENOMEM; 1205 1206 match = of_match_node(rk3x_i2c_match, np); 1207 i2c->soc_data = match->data; 1208 1209 /* use common interface to get I2C timing properties */ 1210 i2c_parse_fw_timings(&pdev->dev, &i2c->t, true); 1211 1212 strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); 1213 i2c->adap.owner = THIS_MODULE; 1214 i2c->adap.algo = &rk3x_i2c_algorithm; 1215 i2c->adap.retries = 3; 1216 i2c->adap.dev.of_node = np; 1217 i2c->adap.algo_data = i2c; 1218 i2c->adap.dev.parent = &pdev->dev; 1219 1220 i2c->dev = &pdev->dev; 1221 1222 spin_lock_init(&i2c->lock); 1223 init_waitqueue_head(&i2c->wait); 1224 1225 i2c->regs = devm_platform_ioremap_resource(pdev, 0); 1226 if (IS_ERR(i2c->regs)) 1227 return PTR_ERR(i2c->regs); 1228 1229 /* Try to set the I2C adapter number from dt */ 1230 bus_nr = of_alias_get_id(np, "i2c"); 1231 1232 /* 1233 * Switch to new interface if the SoC also offers the old one. 1234 * The control bit is located in the GRF register space. 1235 */ 1236 if (i2c->soc_data->grf_offset >= 0) { 1237 struct regmap *grf; 1238 1239 grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); 1240 if (IS_ERR(grf)) { 1241 dev_err(&pdev->dev, 1242 "rk3x-i2c needs 'rockchip,grf' property\n"); 1243 return PTR_ERR(grf); 1244 } 1245 1246 if (bus_nr < 0) { 1247 dev_err(&pdev->dev, "rk3x-i2c needs i2cX alias"); 1248 return -EINVAL; 1249 } 1250 1251 /* 27+i: write mask, 11+i: value */ 1252 value = BIT(27 + bus_nr) | BIT(11 + bus_nr); 1253 1254 ret = regmap_write(grf, i2c->soc_data->grf_offset, value); 1255 if (ret != 0) { 1256 dev_err(i2c->dev, "Could not write to GRF: %d\n", ret); 1257 return ret; 1258 } 1259 } 1260 1261 /* IRQ setup */ 1262 irq = platform_get_irq(pdev, 0); 1263 if (irq < 0) 1264 return irq; 1265 1266 ret = devm_request_irq(&pdev->dev, irq, rk3x_i2c_irq, 1267 0, dev_name(&pdev->dev), i2c); 1268 if (ret < 0) { 1269 dev_err(&pdev->dev, "cannot request IRQ\n"); 1270 return ret; 1271 } 1272 1273 platform_set_drvdata(pdev, i2c); 1274 1275 if (i2c->soc_data->calc_timings == rk3x_i2c_v0_calc_timings) { 1276 /* Only one clock to use for bus clock and peripheral clock */ 1277 i2c->clk = devm_clk_get(&pdev->dev, NULL); 1278 i2c->pclk = i2c->clk; 1279 } else { 1280 i2c->clk = devm_clk_get(&pdev->dev, "i2c"); 1281 i2c->pclk = devm_clk_get(&pdev->dev, "pclk"); 1282 } 1283 1284 if (IS_ERR(i2c->clk)) { 1285 ret = PTR_ERR(i2c->clk); 1286 if (ret != -EPROBE_DEFER) 1287 dev_err(&pdev->dev, "Can't get bus clk: %d\n", ret); 1288 return ret; 1289 } 1290 if (IS_ERR(i2c->pclk)) { 1291 ret = PTR_ERR(i2c->pclk); 1292 if (ret != -EPROBE_DEFER) 1293 dev_err(&pdev->dev, "Can't get periph clk: %d\n", ret); 1294 return ret; 1295 } 1296 1297 ret = clk_prepare(i2c->clk); 1298 if (ret < 0) { 1299 dev_err(&pdev->dev, "Can't prepare bus clk: %d\n", ret); 1300 return ret; 1301 } 1302 ret = clk_prepare(i2c->pclk); 1303 if (ret < 0) { 1304 dev_err(&pdev->dev, "Can't prepare periph clock: %d\n", ret); 1305 goto err_clk; 1306 } 1307 1308 i2c->clk_rate_nb.notifier_call = rk3x_i2c_clk_notifier_cb; 1309 ret = clk_notifier_register(i2c->clk, &i2c->clk_rate_nb); 1310 if (ret != 0) { 1311 dev_err(&pdev->dev, "Unable to register clock notifier\n"); 1312 goto err_pclk; 1313 } 1314 1315 clk_rate = clk_get_rate(i2c->clk); 1316 rk3x_i2c_adapt_div(i2c, clk_rate); 1317 1318 ret = i2c_add_adapter(&i2c->adap); 1319 if (ret < 0) 1320 goto err_clk_notifier; 1321 1322 return 0; 1323 1324 err_clk_notifier: 1325 clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb); 1326 err_pclk: 1327 clk_unprepare(i2c->pclk); 1328 err_clk: 1329 clk_unprepare(i2c->clk); 1330 return ret; 1331 } 1332 1333 static int rk3x_i2c_remove(struct platform_device *pdev) 1334 { 1335 struct rk3x_i2c *i2c = platform_get_drvdata(pdev); 1336 1337 i2c_del_adapter(&i2c->adap); 1338 1339 clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb); 1340 clk_unprepare(i2c->pclk); 1341 clk_unprepare(i2c->clk); 1342 1343 return 0; 1344 } 1345 1346 static SIMPLE_DEV_PM_OPS(rk3x_i2c_pm_ops, NULL, rk3x_i2c_resume); 1347 1348 static struct platform_driver rk3x_i2c_driver = { 1349 .probe = rk3x_i2c_probe, 1350 .remove = rk3x_i2c_remove, 1351 .driver = { 1352 .name = "rk3x-i2c", 1353 .of_match_table = rk3x_i2c_match, 1354 .pm = &rk3x_i2c_pm_ops, 1355 }, 1356 }; 1357 1358 module_platform_driver(rk3x_i2c_driver); 1359 1360 MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver"); 1361 MODULE_AUTHOR("Max Schwarz <max.schwarz@online.de>"); 1362 MODULE_LICENSE("GPL v2"); 1363