1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * TI OMAP I2C master mode driver 4 * 5 * Copyright (C) 2003 MontaVista Software, Inc. 6 * Copyright (C) 2005 Nokia Corporation 7 * Copyright (C) 2004 - 2007 Texas Instruments. 8 * 9 * Originally written by MontaVista Software, Inc. 10 * Additional contributions by: 11 * Tony Lindgren <tony@atomide.com> 12 * Imre Deak <imre.deak@nokia.com> 13 * Juha Yrjölä <juha.yrjola@solidboot.com> 14 * Syed Khasim <x0khasim@ti.com> 15 * Nishant Menon <nm@ti.com> 16 */ 17 18 #include <linux/module.h> 19 #include <linux/delay.h> 20 #include <linux/i2c.h> 21 #include <linux/err.h> 22 #include <linux/interrupt.h> 23 #include <linux/completion.h> 24 #include <linux/platform_device.h> 25 #include <linux/clk.h> 26 #include <linux/io.h> 27 #include <linux/of.h> 28 #include <linux/of_device.h> 29 #include <linux/slab.h> 30 #include <linux/platform_data/i2c-omap.h> 31 #include <linux/pm_runtime.h> 32 #include <linux/pinctrl/consumer.h> 33 34 /* I2C controller revisions */ 35 #define OMAP_I2C_OMAP1_REV_2 0x20 36 37 /* I2C controller revisions present on specific hardware */ 38 #define OMAP_I2C_REV_ON_2430 0x00000036 39 #define OMAP_I2C_REV_ON_3430_3530 0x0000003C 40 #define OMAP_I2C_REV_ON_3630 0x00000040 41 #define OMAP_I2C_REV_ON_4430_PLUS 0x50400002 42 43 /* timeout waiting for the controller to respond */ 44 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000)) 45 46 /* timeout for pm runtime autosuspend */ 47 #define OMAP_I2C_PM_TIMEOUT 1000 /* ms */ 48 49 /* timeout for making decision on bus free status */ 50 #define OMAP_I2C_BUS_FREE_TIMEOUT (msecs_to_jiffies(10)) 51 52 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */ 53 enum { 54 OMAP_I2C_REV_REG = 0, 55 OMAP_I2C_IE_REG, 56 OMAP_I2C_STAT_REG, 57 OMAP_I2C_IV_REG, 58 OMAP_I2C_WE_REG, 59 OMAP_I2C_SYSS_REG, 60 OMAP_I2C_BUF_REG, 61 OMAP_I2C_CNT_REG, 62 OMAP_I2C_DATA_REG, 63 OMAP_I2C_SYSC_REG, 64 OMAP_I2C_CON_REG, 65 OMAP_I2C_OA_REG, 66 OMAP_I2C_SA_REG, 67 OMAP_I2C_PSC_REG, 68 OMAP_I2C_SCLL_REG, 69 OMAP_I2C_SCLH_REG, 70 OMAP_I2C_SYSTEST_REG, 71 OMAP_I2C_BUFSTAT_REG, 72 /* only on OMAP4430 */ 73 OMAP_I2C_IP_V2_REVNB_LO, 74 OMAP_I2C_IP_V2_REVNB_HI, 75 OMAP_I2C_IP_V2_IRQSTATUS_RAW, 76 OMAP_I2C_IP_V2_IRQENABLE_SET, 77 OMAP_I2C_IP_V2_IRQENABLE_CLR, 78 }; 79 80 /* I2C Interrupt Enable Register (OMAP_I2C_IE): */ 81 #define OMAP_I2C_IE_XDR (1 << 14) /* TX Buffer drain int enable */ 82 #define OMAP_I2C_IE_RDR (1 << 13) /* RX Buffer drain int enable */ 83 #define OMAP_I2C_IE_XRDY (1 << 4) /* TX data ready int enable */ 84 #define OMAP_I2C_IE_RRDY (1 << 3) /* RX data ready int enable */ 85 #define OMAP_I2C_IE_ARDY (1 << 2) /* Access ready int enable */ 86 #define OMAP_I2C_IE_NACK (1 << 1) /* No ack interrupt enable */ 87 #define OMAP_I2C_IE_AL (1 << 0) /* Arbitration lost int ena */ 88 89 /* I2C Status Register (OMAP_I2C_STAT): */ 90 #define OMAP_I2C_STAT_XDR (1 << 14) /* TX Buffer draining */ 91 #define OMAP_I2C_STAT_RDR (1 << 13) /* RX Buffer draining */ 92 #define OMAP_I2C_STAT_BB (1 << 12) /* Bus busy */ 93 #define OMAP_I2C_STAT_ROVR (1 << 11) /* Receive overrun */ 94 #define OMAP_I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ 95 #define OMAP_I2C_STAT_AAS (1 << 9) /* Address as slave */ 96 #define OMAP_I2C_STAT_BF (1 << 8) /* Bus Free */ 97 #define OMAP_I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ 98 #define OMAP_I2C_STAT_RRDY (1 << 3) /* Receive data ready */ 99 #define OMAP_I2C_STAT_ARDY (1 << 2) /* Register access ready */ 100 #define OMAP_I2C_STAT_NACK (1 << 1) /* No ack interrupt enable */ 101 #define OMAP_I2C_STAT_AL (1 << 0) /* Arbitration lost int ena */ 102 103 /* I2C WE wakeup enable register */ 104 #define OMAP_I2C_WE_XDR_WE (1 << 14) /* TX drain wakup */ 105 #define OMAP_I2C_WE_RDR_WE (1 << 13) /* RX drain wakeup */ 106 #define OMAP_I2C_WE_AAS_WE (1 << 9) /* Address as slave wakeup*/ 107 #define OMAP_I2C_WE_BF_WE (1 << 8) /* Bus free wakeup */ 108 #define OMAP_I2C_WE_STC_WE (1 << 6) /* Start condition wakeup */ 109 #define OMAP_I2C_WE_GC_WE (1 << 5) /* General call wakeup */ 110 #define OMAP_I2C_WE_DRDY_WE (1 << 3) /* TX/RX data ready wakeup */ 111 #define OMAP_I2C_WE_ARDY_WE (1 << 2) /* Reg access ready wakeup */ 112 #define OMAP_I2C_WE_NACK_WE (1 << 1) /* No acknowledgment wakeup */ 113 #define OMAP_I2C_WE_AL_WE (1 << 0) /* Arbitration lost wakeup */ 114 115 #define OMAP_I2C_WE_ALL (OMAP_I2C_WE_XDR_WE | OMAP_I2C_WE_RDR_WE | \ 116 OMAP_I2C_WE_AAS_WE | OMAP_I2C_WE_BF_WE | \ 117 OMAP_I2C_WE_STC_WE | OMAP_I2C_WE_GC_WE | \ 118 OMAP_I2C_WE_DRDY_WE | OMAP_I2C_WE_ARDY_WE | \ 119 OMAP_I2C_WE_NACK_WE | OMAP_I2C_WE_AL_WE) 120 121 /* I2C Buffer Configuration Register (OMAP_I2C_BUF): */ 122 #define OMAP_I2C_BUF_RDMA_EN (1 << 15) /* RX DMA channel enable */ 123 #define OMAP_I2C_BUF_RXFIF_CLR (1 << 14) /* RX FIFO Clear */ 124 #define OMAP_I2C_BUF_XDMA_EN (1 << 7) /* TX DMA channel enable */ 125 #define OMAP_I2C_BUF_TXFIF_CLR (1 << 6) /* TX FIFO Clear */ 126 127 /* I2C Configuration Register (OMAP_I2C_CON): */ 128 #define OMAP_I2C_CON_EN (1 << 15) /* I2C module enable */ 129 #define OMAP_I2C_CON_BE (1 << 14) /* Big endian mode */ 130 #define OMAP_I2C_CON_OPMODE_HS (1 << 12) /* High Speed support */ 131 #define OMAP_I2C_CON_STB (1 << 11) /* Start byte mode (master) */ 132 #define OMAP_I2C_CON_MST (1 << 10) /* Master/slave mode */ 133 #define OMAP_I2C_CON_TRX (1 << 9) /* TX/RX mode (master only) */ 134 #define OMAP_I2C_CON_XA (1 << 8) /* Expand address */ 135 #define OMAP_I2C_CON_RM (1 << 2) /* Repeat mode (master only) */ 136 #define OMAP_I2C_CON_STP (1 << 1) /* Stop cond (master only) */ 137 #define OMAP_I2C_CON_STT (1 << 0) /* Start condition (master) */ 138 139 /* I2C SCL time value when Master */ 140 #define OMAP_I2C_SCLL_HSSCLL 8 141 #define OMAP_I2C_SCLH_HSSCLH 8 142 143 /* I2C System Test Register (OMAP_I2C_SYSTEST): */ 144 #define OMAP_I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ 145 #define OMAP_I2C_SYSTEST_FREE (1 << 14) /* Free running mode */ 146 #define OMAP_I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ 147 #define OMAP_I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ 148 /* Functional mode */ 149 #define OMAP_I2C_SYSTEST_SCL_I_FUNC (1 << 8) /* SCL line input value */ 150 #define OMAP_I2C_SYSTEST_SCL_O_FUNC (1 << 7) /* SCL line output value */ 151 #define OMAP_I2C_SYSTEST_SDA_I_FUNC (1 << 6) /* SDA line input value */ 152 #define OMAP_I2C_SYSTEST_SDA_O_FUNC (1 << 5) /* SDA line output value */ 153 /* SDA/SCL IO mode */ 154 #define OMAP_I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense in */ 155 #define OMAP_I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive out */ 156 #define OMAP_I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense in */ 157 #define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */ 158 159 /* OCP_SYSSTATUS bit definitions */ 160 #define SYSS_RESETDONE_MASK (1 << 0) 161 162 /* OCP_SYSCONFIG bit definitions */ 163 #define SYSC_CLOCKACTIVITY_MASK (0x3 << 8) 164 #define SYSC_SIDLEMODE_MASK (0x3 << 3) 165 #define SYSC_ENAWAKEUP_MASK (1 << 2) 166 #define SYSC_SOFTRESET_MASK (1 << 1) 167 #define SYSC_AUTOIDLE_MASK (1 << 0) 168 169 #define SYSC_IDLEMODE_SMART 0x2 170 #define SYSC_CLOCKACTIVITY_FCLK 0x2 171 172 /* Errata definitions */ 173 #define I2C_OMAP_ERRATA_I207 (1 << 0) 174 #define I2C_OMAP_ERRATA_I462 (1 << 1) 175 176 #define OMAP_I2C_IP_V2_INTERRUPTS_MASK 0x6FFF 177 178 struct omap_i2c_dev { 179 struct device *dev; 180 void __iomem *base; /* virtual */ 181 int irq; 182 int reg_shift; /* bit shift for I2C register addresses */ 183 struct completion cmd_complete; 184 struct resource *ioarea; 185 u32 latency; /* maximum mpu wkup latency */ 186 void (*set_mpu_wkup_lat)(struct device *dev, 187 long latency); 188 u32 speed; /* Speed of bus in kHz */ 189 u32 flags; 190 u16 scheme; 191 u16 cmd_err; 192 u8 *buf; 193 u8 *regs; 194 size_t buf_len; 195 struct i2c_adapter adapter; 196 u8 threshold; 197 u8 fifo_size; /* use as flag and value 198 * fifo_size==0 implies no fifo 199 * if set, should be trsh+1 200 */ 201 u32 rev; 202 unsigned b_hw:1; /* bad h/w fixes */ 203 unsigned bb_valid:1; /* true when BB-bit reflects 204 * the I2C bus state 205 */ 206 unsigned receiver:1; /* true when we're in receiver mode */ 207 u16 iestate; /* Saved interrupt register */ 208 u16 pscstate; 209 u16 scllstate; 210 u16 sclhstate; 211 u16 syscstate; 212 u16 westate; 213 u16 errata; 214 }; 215 216 static const u8 reg_map_ip_v1[] = { 217 [OMAP_I2C_REV_REG] = 0x00, 218 [OMAP_I2C_IE_REG] = 0x01, 219 [OMAP_I2C_STAT_REG] = 0x02, 220 [OMAP_I2C_IV_REG] = 0x03, 221 [OMAP_I2C_WE_REG] = 0x03, 222 [OMAP_I2C_SYSS_REG] = 0x04, 223 [OMAP_I2C_BUF_REG] = 0x05, 224 [OMAP_I2C_CNT_REG] = 0x06, 225 [OMAP_I2C_DATA_REG] = 0x07, 226 [OMAP_I2C_SYSC_REG] = 0x08, 227 [OMAP_I2C_CON_REG] = 0x09, 228 [OMAP_I2C_OA_REG] = 0x0a, 229 [OMAP_I2C_SA_REG] = 0x0b, 230 [OMAP_I2C_PSC_REG] = 0x0c, 231 [OMAP_I2C_SCLL_REG] = 0x0d, 232 [OMAP_I2C_SCLH_REG] = 0x0e, 233 [OMAP_I2C_SYSTEST_REG] = 0x0f, 234 [OMAP_I2C_BUFSTAT_REG] = 0x10, 235 }; 236 237 static const u8 reg_map_ip_v2[] = { 238 [OMAP_I2C_REV_REG] = 0x04, 239 [OMAP_I2C_IE_REG] = 0x2c, 240 [OMAP_I2C_STAT_REG] = 0x28, 241 [OMAP_I2C_IV_REG] = 0x34, 242 [OMAP_I2C_WE_REG] = 0x34, 243 [OMAP_I2C_SYSS_REG] = 0x90, 244 [OMAP_I2C_BUF_REG] = 0x94, 245 [OMAP_I2C_CNT_REG] = 0x98, 246 [OMAP_I2C_DATA_REG] = 0x9c, 247 [OMAP_I2C_SYSC_REG] = 0x10, 248 [OMAP_I2C_CON_REG] = 0xa4, 249 [OMAP_I2C_OA_REG] = 0xa8, 250 [OMAP_I2C_SA_REG] = 0xac, 251 [OMAP_I2C_PSC_REG] = 0xb0, 252 [OMAP_I2C_SCLL_REG] = 0xb4, 253 [OMAP_I2C_SCLH_REG] = 0xb8, 254 [OMAP_I2C_SYSTEST_REG] = 0xbC, 255 [OMAP_I2C_BUFSTAT_REG] = 0xc0, 256 [OMAP_I2C_IP_V2_REVNB_LO] = 0x00, 257 [OMAP_I2C_IP_V2_REVNB_HI] = 0x04, 258 [OMAP_I2C_IP_V2_IRQSTATUS_RAW] = 0x24, 259 [OMAP_I2C_IP_V2_IRQENABLE_SET] = 0x2c, 260 [OMAP_I2C_IP_V2_IRQENABLE_CLR] = 0x30, 261 }; 262 263 static int omap_i2c_xfer_data(struct omap_i2c_dev *omap); 264 265 static inline void omap_i2c_write_reg(struct omap_i2c_dev *omap, 266 int reg, u16 val) 267 { 268 writew_relaxed(val, omap->base + 269 (omap->regs[reg] << omap->reg_shift)); 270 } 271 272 static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *omap, int reg) 273 { 274 return readw_relaxed(omap->base + 275 (omap->regs[reg] << omap->reg_shift)); 276 } 277 278 static void __omap_i2c_init(struct omap_i2c_dev *omap) 279 { 280 281 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 282 283 /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ 284 omap_i2c_write_reg(omap, OMAP_I2C_PSC_REG, omap->pscstate); 285 286 /* SCL low and high time values */ 287 omap_i2c_write_reg(omap, OMAP_I2C_SCLL_REG, omap->scllstate); 288 omap_i2c_write_reg(omap, OMAP_I2C_SCLH_REG, omap->sclhstate); 289 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) 290 omap_i2c_write_reg(omap, OMAP_I2C_WE_REG, omap->westate); 291 292 /* Take the I2C module out of reset: */ 293 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); 294 295 /* 296 * NOTE: right after setting CON_EN, STAT_BB could be 0 while the 297 * bus is busy. It will be changed to 1 on the next IP FCLK clock. 298 * udelay(1) will be enough to fix that. 299 */ 300 301 /* 302 * Don't write to this register if the IE state is 0 as it can 303 * cause deadlock. 304 */ 305 if (omap->iestate) 306 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, omap->iestate); 307 } 308 309 static int omap_i2c_reset(struct omap_i2c_dev *omap) 310 { 311 unsigned long timeout; 312 u16 sysc; 313 314 if (omap->rev >= OMAP_I2C_OMAP1_REV_2) { 315 sysc = omap_i2c_read_reg(omap, OMAP_I2C_SYSC_REG); 316 317 /* Disable I2C controller before soft reset */ 318 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 319 omap_i2c_read_reg(omap, OMAP_I2C_CON_REG) & 320 ~(OMAP_I2C_CON_EN)); 321 322 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, SYSC_SOFTRESET_MASK); 323 /* For some reason we need to set the EN bit before the 324 * reset done bit gets set. */ 325 timeout = jiffies + OMAP_I2C_TIMEOUT; 326 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); 327 while (!(omap_i2c_read_reg(omap, OMAP_I2C_SYSS_REG) & 328 SYSS_RESETDONE_MASK)) { 329 if (time_after(jiffies, timeout)) { 330 dev_warn(omap->dev, "timeout waiting " 331 "for controller reset\n"); 332 return -ETIMEDOUT; 333 } 334 msleep(1); 335 } 336 337 /* SYSC register is cleared by the reset; rewrite it */ 338 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, sysc); 339 340 if (omap->rev > OMAP_I2C_REV_ON_3430_3530) { 341 /* Schedule I2C-bus monitoring on the next transfer */ 342 omap->bb_valid = 0; 343 } 344 } 345 346 return 0; 347 } 348 349 static int omap_i2c_init(struct omap_i2c_dev *omap) 350 { 351 u16 psc = 0, scll = 0, sclh = 0; 352 u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; 353 unsigned long fclk_rate = 12000000; 354 unsigned long internal_clk = 0; 355 struct clk *fclk; 356 int error; 357 358 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) { 359 /* 360 * Enabling all wakup sources to stop I2C freezing on 361 * WFI instruction. 362 * REVISIT: Some wkup sources might not be needed. 363 */ 364 omap->westate = OMAP_I2C_WE_ALL; 365 } 366 367 if (omap->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) { 368 /* 369 * The I2C functional clock is the armxor_ck, so there's 370 * no need to get "armxor_ck" separately. Now, if OMAP2420 371 * always returns 12MHz for the functional clock, we can 372 * do this bit unconditionally. 373 */ 374 fclk = clk_get(omap->dev, "fck"); 375 if (IS_ERR(fclk)) { 376 error = PTR_ERR(fclk); 377 dev_err(omap->dev, "could not get fck: %i\n", error); 378 379 return error; 380 } 381 382 fclk_rate = clk_get_rate(fclk); 383 clk_put(fclk); 384 385 /* TRM for 5912 says the I2C clock must be prescaled to be 386 * between 7 - 12 MHz. The XOR input clock is typically 387 * 12, 13 or 19.2 MHz. So we should have code that produces: 388 * 389 * XOR MHz Divider Prescaler 390 * 12 1 0 391 * 13 2 1 392 * 19.2 2 1 393 */ 394 if (fclk_rate > 12000000) 395 psc = fclk_rate / 12000000; 396 } 397 398 if (!(omap->flags & OMAP_I2C_FLAG_SIMPLE_CLOCK)) { 399 400 /* 401 * HSI2C controller internal clk rate should be 19.2 Mhz for 402 * HS and for all modes on 2430. On 34xx we can use lower rate 403 * to get longer filter period for better noise suppression. 404 * The filter is iclk (fclk for HS) period. 405 */ 406 if (omap->speed > 400 || 407 omap->flags & OMAP_I2C_FLAG_FORCE_19200_INT_CLK) 408 internal_clk = 19200; 409 else if (omap->speed > 100) 410 internal_clk = 9600; 411 else 412 internal_clk = 4000; 413 fclk = clk_get(omap->dev, "fck"); 414 if (IS_ERR(fclk)) { 415 error = PTR_ERR(fclk); 416 dev_err(omap->dev, "could not get fck: %i\n", error); 417 418 return error; 419 } 420 fclk_rate = clk_get_rate(fclk) / 1000; 421 clk_put(fclk); 422 423 /* Compute prescaler divisor */ 424 psc = fclk_rate / internal_clk; 425 psc = psc - 1; 426 427 /* If configured for High Speed */ 428 if (omap->speed > 400) { 429 unsigned long scl; 430 431 /* For first phase of HS mode */ 432 scl = internal_clk / 400; 433 fsscll = scl - (scl / 3) - 7; 434 fssclh = (scl / 3) - 5; 435 436 /* For second phase of HS mode */ 437 scl = fclk_rate / omap->speed; 438 hsscll = scl - (scl / 3) - 7; 439 hssclh = (scl / 3) - 5; 440 } else if (omap->speed > 100) { 441 unsigned long scl; 442 443 /* Fast mode */ 444 scl = internal_clk / omap->speed; 445 fsscll = scl - (scl / 3) - 7; 446 fssclh = (scl / 3) - 5; 447 } else { 448 /* Standard mode */ 449 fsscll = internal_clk / (omap->speed * 2) - 7; 450 fssclh = internal_clk / (omap->speed * 2) - 5; 451 } 452 scll = (hsscll << OMAP_I2C_SCLL_HSSCLL) | fsscll; 453 sclh = (hssclh << OMAP_I2C_SCLH_HSSCLH) | fssclh; 454 } else { 455 /* Program desired operating rate */ 456 fclk_rate /= (psc + 1) * 1000; 457 if (psc > 2) 458 psc = 2; 459 scll = fclk_rate / (omap->speed * 2) - 7 + psc; 460 sclh = fclk_rate / (omap->speed * 2) - 7 + psc; 461 } 462 463 omap->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY | 464 OMAP_I2C_IE_ARDY | OMAP_I2C_IE_NACK | 465 OMAP_I2C_IE_AL) | ((omap->fifo_size) ? 466 (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0); 467 468 omap->pscstate = psc; 469 omap->scllstate = scll; 470 omap->sclhstate = sclh; 471 472 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530) { 473 /* Not implemented */ 474 omap->bb_valid = 1; 475 } 476 477 __omap_i2c_init(omap); 478 479 return 0; 480 } 481 482 /* 483 * Try bus recovery, but only if SDA is actually low. 484 */ 485 static int omap_i2c_recover_bus(struct omap_i2c_dev *omap) 486 { 487 u16 systest; 488 489 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG); 490 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) && 491 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC)) 492 return 0; /* bus seems to already be fine */ 493 if (!(systest & OMAP_I2C_SYSTEST_SCL_I_FUNC)) 494 return -EBUSY; /* recovery would not fix SCL */ 495 return i2c_recover_bus(&omap->adapter); 496 } 497 498 /* 499 * Waiting on Bus Busy 500 */ 501 static int omap_i2c_wait_for_bb(struct omap_i2c_dev *omap) 502 { 503 unsigned long timeout; 504 505 timeout = jiffies + OMAP_I2C_TIMEOUT; 506 while (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) & OMAP_I2C_STAT_BB) { 507 if (time_after(jiffies, timeout)) 508 return omap_i2c_recover_bus(omap); 509 msleep(1); 510 } 511 512 return 0; 513 } 514 515 /* 516 * Wait while BB-bit doesn't reflect the I2C bus state 517 * 518 * In a multimaster environment, after IP software reset, BB-bit value doesn't 519 * correspond to the current bus state. It may happen what BB-bit will be 0, 520 * while the bus is busy due to another I2C master activity. 521 * Here are BB-bit values after reset: 522 * SDA SCL BB NOTES 523 * 0 0 0 1, 2 524 * 1 0 0 1, 2 525 * 0 1 1 526 * 1 1 0 3 527 * Later, if IP detect SDA=0 and SCL=1 (ACK) or SDA 1->0 while SCL=1 (START) 528 * combinations on the bus, it set BB-bit to 1. 529 * If IP detect SDA 0->1 while SCL=1 (STOP) combination on the bus, 530 * it set BB-bit to 0 and BF to 1. 531 * BB and BF bits correctly tracks the bus state while IP is suspended 532 * BB bit became valid on the next FCLK clock after CON_EN bit set 533 * 534 * NOTES: 535 * 1. Any transfer started when BB=0 and bus is busy wouldn't be 536 * completed by IP and results in controller timeout. 537 * 2. Any transfer started when BB=0 and SCL=0 results in IP 538 * starting to drive SDA low. In that case IP corrupt data 539 * on the bus. 540 * 3. Any transfer started in the middle of another master's transfer 541 * results in unpredictable results and data corruption 542 */ 543 static int omap_i2c_wait_for_bb_valid(struct omap_i2c_dev *omap) 544 { 545 unsigned long bus_free_timeout = 0; 546 unsigned long timeout; 547 int bus_free = 0; 548 u16 stat, systest; 549 550 if (omap->bb_valid) 551 return 0; 552 553 timeout = jiffies + OMAP_I2C_TIMEOUT; 554 while (1) { 555 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 556 /* 557 * We will see BB or BF event in a case IP had detected any 558 * activity on the I2C bus. Now IP correctly tracks the bus 559 * state. BB-bit value is valid. 560 */ 561 if (stat & (OMAP_I2C_STAT_BB | OMAP_I2C_STAT_BF)) 562 break; 563 564 /* 565 * Otherwise, we must look signals on the bus to make 566 * the right decision. 567 */ 568 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG); 569 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) && 570 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC)) { 571 if (!bus_free) { 572 bus_free_timeout = jiffies + 573 OMAP_I2C_BUS_FREE_TIMEOUT; 574 bus_free = 1; 575 } 576 577 /* 578 * SDA and SCL lines was high for 10 ms without bus 579 * activity detected. The bus is free. Consider 580 * BB-bit value is valid. 581 */ 582 if (time_after(jiffies, bus_free_timeout)) 583 break; 584 } else { 585 bus_free = 0; 586 } 587 588 if (time_after(jiffies, timeout)) { 589 /* 590 * SDA or SCL were low for the entire timeout without 591 * any activity detected. Most likely, a slave is 592 * locking up the bus with no master driving the clock. 593 */ 594 dev_warn(omap->dev, "timeout waiting for bus ready\n"); 595 return omap_i2c_recover_bus(omap); 596 } 597 598 msleep(1); 599 } 600 601 omap->bb_valid = 1; 602 return 0; 603 } 604 605 static void omap_i2c_resize_fifo(struct omap_i2c_dev *omap, u8 size, bool is_rx) 606 { 607 u16 buf; 608 609 if (omap->flags & OMAP_I2C_FLAG_NO_FIFO) 610 return; 611 612 /* 613 * Set up notification threshold based on message size. We're doing 614 * this to try and avoid draining feature as much as possible. Whenever 615 * we have big messages to transfer (bigger than our total fifo size) 616 * then we might use draining feature to transfer the remaining bytes. 617 */ 618 619 omap->threshold = clamp(size, (u8) 1, omap->fifo_size); 620 621 buf = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG); 622 623 if (is_rx) { 624 /* Clear RX Threshold */ 625 buf &= ~(0x3f << 8); 626 buf |= ((omap->threshold - 1) << 8) | OMAP_I2C_BUF_RXFIF_CLR; 627 } else { 628 /* Clear TX Threshold */ 629 buf &= ~0x3f; 630 buf |= (omap->threshold - 1) | OMAP_I2C_BUF_TXFIF_CLR; 631 } 632 633 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, buf); 634 635 if (omap->rev < OMAP_I2C_REV_ON_3630) 636 omap->b_hw = 1; /* Enable hardware fixes */ 637 638 /* calculate wakeup latency constraint for MPU */ 639 if (omap->set_mpu_wkup_lat != NULL) 640 omap->latency = (1000000 * omap->threshold) / 641 (1000 * omap->speed / 8); 642 } 643 644 static void omap_i2c_wait(struct omap_i2c_dev *omap) 645 { 646 u16 stat; 647 u16 mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 648 int count = 0; 649 650 do { 651 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 652 count++; 653 } while (!(stat & mask) && count < 5); 654 } 655 656 /* 657 * Low level master read/write transaction. 658 */ 659 static int omap_i2c_xfer_msg(struct i2c_adapter *adap, 660 struct i2c_msg *msg, int stop, bool polling) 661 { 662 struct omap_i2c_dev *omap = i2c_get_adapdata(adap); 663 unsigned long timeout; 664 u16 w; 665 int ret; 666 667 dev_dbg(omap->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n", 668 msg->addr, msg->len, msg->flags, stop); 669 670 omap->receiver = !!(msg->flags & I2C_M_RD); 671 omap_i2c_resize_fifo(omap, msg->len, omap->receiver); 672 673 omap_i2c_write_reg(omap, OMAP_I2C_SA_REG, msg->addr); 674 675 /* REVISIT: Could the STB bit of I2C_CON be used with probing? */ 676 omap->buf = msg->buf; 677 omap->buf_len = msg->len; 678 679 /* make sure writes to omap->buf_len are ordered */ 680 barrier(); 681 682 omap_i2c_write_reg(omap, OMAP_I2C_CNT_REG, omap->buf_len); 683 684 /* Clear the FIFO Buffers */ 685 w = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG); 686 w |= OMAP_I2C_BUF_RXFIF_CLR | OMAP_I2C_BUF_TXFIF_CLR; 687 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, w); 688 689 if (!polling) 690 reinit_completion(&omap->cmd_complete); 691 omap->cmd_err = 0; 692 693 w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT; 694 695 /* High speed configuration */ 696 if (omap->speed > 400) 697 w |= OMAP_I2C_CON_OPMODE_HS; 698 699 if (msg->flags & I2C_M_STOP) 700 stop = 1; 701 if (msg->flags & I2C_M_TEN) 702 w |= OMAP_I2C_CON_XA; 703 if (!(msg->flags & I2C_M_RD)) 704 w |= OMAP_I2C_CON_TRX; 705 706 if (!omap->b_hw && stop) 707 w |= OMAP_I2C_CON_STP; 708 /* 709 * NOTE: STAT_BB bit could became 1 here if another master occupy 710 * the bus. IP successfully complete transfer when the bus will be 711 * free again (BB reset to 0). 712 */ 713 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 714 715 /* 716 * Don't write stt and stp together on some hardware. 717 */ 718 if (omap->b_hw && stop) { 719 unsigned long delay = jiffies + OMAP_I2C_TIMEOUT; 720 u16 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 721 while (con & OMAP_I2C_CON_STT) { 722 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 723 724 /* Let the user know if i2c is in a bad state */ 725 if (time_after(jiffies, delay)) { 726 dev_err(omap->dev, "controller timed out " 727 "waiting for start condition to finish\n"); 728 return -ETIMEDOUT; 729 } 730 cpu_relax(); 731 } 732 733 w |= OMAP_I2C_CON_STP; 734 w &= ~OMAP_I2C_CON_STT; 735 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 736 } 737 738 /* 739 * REVISIT: We should abort the transfer on signals, but the bus goes 740 * into arbitration and we're currently unable to recover from it. 741 */ 742 if (!polling) { 743 timeout = wait_for_completion_timeout(&omap->cmd_complete, 744 OMAP_I2C_TIMEOUT); 745 } else { 746 do { 747 omap_i2c_wait(omap); 748 ret = omap_i2c_xfer_data(omap); 749 } while (ret == -EAGAIN); 750 751 timeout = !ret; 752 } 753 754 if (timeout == 0) { 755 dev_err(omap->dev, "controller timed out\n"); 756 omap_i2c_reset(omap); 757 __omap_i2c_init(omap); 758 return -ETIMEDOUT; 759 } 760 761 if (likely(!omap->cmd_err)) 762 return 0; 763 764 /* We have an error */ 765 if (omap->cmd_err & (OMAP_I2C_STAT_ROVR | OMAP_I2C_STAT_XUDF)) { 766 omap_i2c_reset(omap); 767 __omap_i2c_init(omap); 768 return -EIO; 769 } 770 771 if (omap->cmd_err & OMAP_I2C_STAT_AL) 772 return -EAGAIN; 773 774 if (omap->cmd_err & OMAP_I2C_STAT_NACK) { 775 if (msg->flags & I2C_M_IGNORE_NAK) 776 return 0; 777 778 w = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 779 w |= OMAP_I2C_CON_STP; 780 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 781 return -EREMOTEIO; 782 } 783 return -EIO; 784 } 785 786 787 /* 788 * Prepare controller for a transaction and call omap_i2c_xfer_msg 789 * to do the work during IRQ processing. 790 */ 791 static int 792 omap_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg msgs[], int num, 793 bool polling) 794 { 795 struct omap_i2c_dev *omap = i2c_get_adapdata(adap); 796 int i; 797 int r; 798 799 r = pm_runtime_get_sync(omap->dev); 800 if (r < 0) 801 goto out; 802 803 r = omap_i2c_wait_for_bb_valid(omap); 804 if (r < 0) 805 goto out; 806 807 r = omap_i2c_wait_for_bb(omap); 808 if (r < 0) 809 goto out; 810 811 if (omap->set_mpu_wkup_lat != NULL) 812 omap->set_mpu_wkup_lat(omap->dev, omap->latency); 813 814 for (i = 0; i < num; i++) { 815 r = omap_i2c_xfer_msg(adap, &msgs[i], (i == (num - 1)), 816 polling); 817 if (r != 0) 818 break; 819 } 820 821 if (r == 0) 822 r = num; 823 824 omap_i2c_wait_for_bb(omap); 825 826 if (omap->set_mpu_wkup_lat != NULL) 827 omap->set_mpu_wkup_lat(omap->dev, -1); 828 829 out: 830 pm_runtime_mark_last_busy(omap->dev); 831 pm_runtime_put_autosuspend(omap->dev); 832 return r; 833 } 834 835 static int 836 omap_i2c_xfer_irq(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) 837 { 838 return omap_i2c_xfer_common(adap, msgs, num, false); 839 } 840 841 static int 842 omap_i2c_xfer_polling(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) 843 { 844 return omap_i2c_xfer_common(adap, msgs, num, true); 845 } 846 847 static u32 848 omap_i2c_func(struct i2c_adapter *adap) 849 { 850 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | 851 I2C_FUNC_PROTOCOL_MANGLING; 852 } 853 854 static inline void 855 omap_i2c_complete_cmd(struct omap_i2c_dev *omap, u16 err) 856 { 857 omap->cmd_err |= err; 858 complete(&omap->cmd_complete); 859 } 860 861 static inline void 862 omap_i2c_ack_stat(struct omap_i2c_dev *omap, u16 stat) 863 { 864 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, stat); 865 } 866 867 static inline void i2c_omap_errata_i207(struct omap_i2c_dev *omap, u16 stat) 868 { 869 /* 870 * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8) 871 * Not applicable for OMAP4. 872 * Under certain rare conditions, RDR could be set again 873 * when the bus is busy, then ignore the interrupt and 874 * clear the interrupt. 875 */ 876 if (stat & OMAP_I2C_STAT_RDR) { 877 /* Step 1: If RDR is set, clear it */ 878 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 879 880 /* Step 2: */ 881 if (!(omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) 882 & OMAP_I2C_STAT_BB)) { 883 884 /* Step 3: */ 885 if (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) 886 & OMAP_I2C_STAT_RDR) { 887 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 888 dev_dbg(omap->dev, "RDR when bus is busy.\n"); 889 } 890 891 } 892 } 893 } 894 895 /* rev1 devices are apparently only on some 15xx */ 896 #ifdef CONFIG_ARCH_OMAP15XX 897 898 static irqreturn_t 899 omap_i2c_omap1_isr(int this_irq, void *dev_id) 900 { 901 struct omap_i2c_dev *omap = dev_id; 902 u16 iv, w; 903 904 if (pm_runtime_suspended(omap->dev)) 905 return IRQ_NONE; 906 907 iv = omap_i2c_read_reg(omap, OMAP_I2C_IV_REG); 908 switch (iv) { 909 case 0x00: /* None */ 910 break; 911 case 0x01: /* Arbitration lost */ 912 dev_err(omap->dev, "Arbitration lost\n"); 913 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_AL); 914 break; 915 case 0x02: /* No acknowledgement */ 916 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_NACK); 917 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_STP); 918 break; 919 case 0x03: /* Register access ready */ 920 omap_i2c_complete_cmd(omap, 0); 921 break; 922 case 0x04: /* Receive data ready */ 923 if (omap->buf_len) { 924 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG); 925 *omap->buf++ = w; 926 omap->buf_len--; 927 if (omap->buf_len) { 928 *omap->buf++ = w >> 8; 929 omap->buf_len--; 930 } 931 } else 932 dev_err(omap->dev, "RRDY IRQ while no data requested\n"); 933 break; 934 case 0x05: /* Transmit data ready */ 935 if (omap->buf_len) { 936 w = *omap->buf++; 937 omap->buf_len--; 938 if (omap->buf_len) { 939 w |= *omap->buf++ << 8; 940 omap->buf_len--; 941 } 942 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w); 943 } else 944 dev_err(omap->dev, "XRDY IRQ while no data to send\n"); 945 break; 946 default: 947 return IRQ_NONE; 948 } 949 950 return IRQ_HANDLED; 951 } 952 #else 953 #define omap_i2c_omap1_isr NULL 954 #endif 955 956 /* 957 * OMAP3430 Errata i462: When an XRDY/XDR is hit, wait for XUDF before writing 958 * data to DATA_REG. Otherwise some data bytes can be lost while transferring 959 * them from the memory to the I2C interface. 960 */ 961 static int errata_omap3_i462(struct omap_i2c_dev *omap) 962 { 963 unsigned long timeout = 10000; 964 u16 stat; 965 966 do { 967 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 968 if (stat & OMAP_I2C_STAT_XUDF) 969 break; 970 971 if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { 972 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_XRDY | 973 OMAP_I2C_STAT_XDR)); 974 if (stat & OMAP_I2C_STAT_NACK) { 975 omap->cmd_err |= OMAP_I2C_STAT_NACK; 976 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK); 977 } 978 979 if (stat & OMAP_I2C_STAT_AL) { 980 dev_err(omap->dev, "Arbitration lost\n"); 981 omap->cmd_err |= OMAP_I2C_STAT_AL; 982 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL); 983 } 984 985 return -EIO; 986 } 987 988 cpu_relax(); 989 } while (--timeout); 990 991 if (!timeout) { 992 dev_err(omap->dev, "timeout waiting on XUDF bit\n"); 993 return 0; 994 } 995 996 return 0; 997 } 998 999 static void omap_i2c_receive_data(struct omap_i2c_dev *omap, u8 num_bytes, 1000 bool is_rdr) 1001 { 1002 u16 w; 1003 1004 while (num_bytes--) { 1005 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG); 1006 *omap->buf++ = w; 1007 omap->buf_len--; 1008 1009 /* 1010 * Data reg in 2430, omap3 and 1011 * omap4 is 8 bit wide 1012 */ 1013 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) { 1014 *omap->buf++ = w >> 8; 1015 omap->buf_len--; 1016 } 1017 } 1018 } 1019 1020 static int omap_i2c_transmit_data(struct omap_i2c_dev *omap, u8 num_bytes, 1021 bool is_xdr) 1022 { 1023 u16 w; 1024 1025 while (num_bytes--) { 1026 w = *omap->buf++; 1027 omap->buf_len--; 1028 1029 /* 1030 * Data reg in 2430, omap3 and 1031 * omap4 is 8 bit wide 1032 */ 1033 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) { 1034 w |= *omap->buf++ << 8; 1035 omap->buf_len--; 1036 } 1037 1038 if (omap->errata & I2C_OMAP_ERRATA_I462) { 1039 int ret; 1040 1041 ret = errata_omap3_i462(omap); 1042 if (ret < 0) 1043 return ret; 1044 } 1045 1046 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w); 1047 } 1048 1049 return 0; 1050 } 1051 1052 static irqreturn_t 1053 omap_i2c_isr(int irq, void *dev_id) 1054 { 1055 struct omap_i2c_dev *omap = dev_id; 1056 irqreturn_t ret = IRQ_HANDLED; 1057 u16 mask; 1058 u16 stat; 1059 1060 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1061 mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1062 1063 if (stat & mask) 1064 ret = IRQ_WAKE_THREAD; 1065 1066 return ret; 1067 } 1068 1069 static int omap_i2c_xfer_data(struct omap_i2c_dev *omap) 1070 { 1071 u16 bits; 1072 u16 stat; 1073 int err = 0, count = 0; 1074 1075 do { 1076 bits = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1077 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1078 stat &= bits; 1079 1080 /* If we're in receiver mode, ignore XDR/XRDY */ 1081 if (omap->receiver) 1082 stat &= ~(OMAP_I2C_STAT_XDR | OMAP_I2C_STAT_XRDY); 1083 else 1084 stat &= ~(OMAP_I2C_STAT_RDR | OMAP_I2C_STAT_RRDY); 1085 1086 if (!stat) { 1087 /* my work here is done */ 1088 err = -EAGAIN; 1089 break; 1090 } 1091 1092 dev_dbg(omap->dev, "IRQ (ISR = 0x%04x)\n", stat); 1093 if (count++ == 100) { 1094 dev_warn(omap->dev, "Too much work in one IRQ\n"); 1095 break; 1096 } 1097 1098 if (stat & OMAP_I2C_STAT_NACK) { 1099 err |= OMAP_I2C_STAT_NACK; 1100 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK); 1101 } 1102 1103 if (stat & OMAP_I2C_STAT_AL) { 1104 dev_err(omap->dev, "Arbitration lost\n"); 1105 err |= OMAP_I2C_STAT_AL; 1106 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL); 1107 } 1108 1109 /* 1110 * ProDB0017052: Clear ARDY bit twice 1111 */ 1112 if (stat & OMAP_I2C_STAT_ARDY) 1113 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ARDY); 1114 1115 if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | 1116 OMAP_I2C_STAT_AL)) { 1117 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_RRDY | 1118 OMAP_I2C_STAT_RDR | 1119 OMAP_I2C_STAT_XRDY | 1120 OMAP_I2C_STAT_XDR | 1121 OMAP_I2C_STAT_ARDY)); 1122 break; 1123 } 1124 1125 if (stat & OMAP_I2C_STAT_RDR) { 1126 u8 num_bytes = 1; 1127 1128 if (omap->fifo_size) 1129 num_bytes = omap->buf_len; 1130 1131 if (omap->errata & I2C_OMAP_ERRATA_I207) { 1132 i2c_omap_errata_i207(omap, stat); 1133 num_bytes = (omap_i2c_read_reg(omap, 1134 OMAP_I2C_BUFSTAT_REG) >> 8) & 0x3F; 1135 } 1136 1137 omap_i2c_receive_data(omap, num_bytes, true); 1138 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 1139 continue; 1140 } 1141 1142 if (stat & OMAP_I2C_STAT_RRDY) { 1143 u8 num_bytes = 1; 1144 1145 if (omap->threshold) 1146 num_bytes = omap->threshold; 1147 1148 omap_i2c_receive_data(omap, num_bytes, false); 1149 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RRDY); 1150 continue; 1151 } 1152 1153 if (stat & OMAP_I2C_STAT_XDR) { 1154 u8 num_bytes = 1; 1155 int ret; 1156 1157 if (omap->fifo_size) 1158 num_bytes = omap->buf_len; 1159 1160 ret = omap_i2c_transmit_data(omap, num_bytes, true); 1161 if (ret < 0) 1162 break; 1163 1164 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XDR); 1165 continue; 1166 } 1167 1168 if (stat & OMAP_I2C_STAT_XRDY) { 1169 u8 num_bytes = 1; 1170 int ret; 1171 1172 if (omap->threshold) 1173 num_bytes = omap->threshold; 1174 1175 ret = omap_i2c_transmit_data(omap, num_bytes, false); 1176 if (ret < 0) 1177 break; 1178 1179 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XRDY); 1180 continue; 1181 } 1182 1183 if (stat & OMAP_I2C_STAT_ROVR) { 1184 dev_err(omap->dev, "Receive overrun\n"); 1185 err |= OMAP_I2C_STAT_ROVR; 1186 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ROVR); 1187 break; 1188 } 1189 1190 if (stat & OMAP_I2C_STAT_XUDF) { 1191 dev_err(omap->dev, "Transmit underflow\n"); 1192 err |= OMAP_I2C_STAT_XUDF; 1193 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XUDF); 1194 break; 1195 } 1196 } while (stat); 1197 1198 return err; 1199 } 1200 1201 static irqreturn_t 1202 omap_i2c_isr_thread(int this_irq, void *dev_id) 1203 { 1204 int ret; 1205 struct omap_i2c_dev *omap = dev_id; 1206 1207 ret = omap_i2c_xfer_data(omap); 1208 if (ret != -EAGAIN) 1209 omap_i2c_complete_cmd(omap, ret); 1210 1211 return IRQ_HANDLED; 1212 } 1213 1214 static const struct i2c_algorithm omap_i2c_algo = { 1215 .master_xfer = omap_i2c_xfer_irq, 1216 .master_xfer_atomic = omap_i2c_xfer_polling, 1217 .functionality = omap_i2c_func, 1218 }; 1219 1220 static const struct i2c_adapter_quirks omap_i2c_quirks = { 1221 .flags = I2C_AQ_NO_ZERO_LEN, 1222 }; 1223 1224 #ifdef CONFIG_OF 1225 static struct omap_i2c_bus_platform_data omap2420_pdata = { 1226 .rev = OMAP_I2C_IP_VERSION_1, 1227 .flags = OMAP_I2C_FLAG_NO_FIFO | 1228 OMAP_I2C_FLAG_SIMPLE_CLOCK | 1229 OMAP_I2C_FLAG_16BIT_DATA_REG | 1230 OMAP_I2C_FLAG_BUS_SHIFT_2, 1231 }; 1232 1233 static struct omap_i2c_bus_platform_data omap2430_pdata = { 1234 .rev = OMAP_I2C_IP_VERSION_1, 1235 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2 | 1236 OMAP_I2C_FLAG_FORCE_19200_INT_CLK, 1237 }; 1238 1239 static struct omap_i2c_bus_platform_data omap3_pdata = { 1240 .rev = OMAP_I2C_IP_VERSION_1, 1241 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2, 1242 }; 1243 1244 static struct omap_i2c_bus_platform_data omap4_pdata = { 1245 .rev = OMAP_I2C_IP_VERSION_2, 1246 }; 1247 1248 static const struct of_device_id omap_i2c_of_match[] = { 1249 { 1250 .compatible = "ti,omap4-i2c", 1251 .data = &omap4_pdata, 1252 }, 1253 { 1254 .compatible = "ti,omap3-i2c", 1255 .data = &omap3_pdata, 1256 }, 1257 { 1258 .compatible = "ti,omap2430-i2c", 1259 .data = &omap2430_pdata, 1260 }, 1261 { 1262 .compatible = "ti,omap2420-i2c", 1263 .data = &omap2420_pdata, 1264 }, 1265 { }, 1266 }; 1267 MODULE_DEVICE_TABLE(of, omap_i2c_of_match); 1268 #endif 1269 1270 #define OMAP_I2C_SCHEME(rev) ((rev & 0xc000) >> 14) 1271 1272 #define OMAP_I2C_REV_SCHEME_0_MAJOR(rev) (rev >> 4) 1273 #define OMAP_I2C_REV_SCHEME_0_MINOR(rev) (rev & 0xf) 1274 1275 #define OMAP_I2C_REV_SCHEME_1_MAJOR(rev) ((rev & 0x0700) >> 7) 1276 #define OMAP_I2C_REV_SCHEME_1_MINOR(rev) (rev & 0x1f) 1277 #define OMAP_I2C_SCHEME_0 0 1278 #define OMAP_I2C_SCHEME_1 1 1279 1280 static int omap_i2c_get_scl(struct i2c_adapter *adap) 1281 { 1282 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1283 u32 reg; 1284 1285 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1286 1287 return reg & OMAP_I2C_SYSTEST_SCL_I_FUNC; 1288 } 1289 1290 static int omap_i2c_get_sda(struct i2c_adapter *adap) 1291 { 1292 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1293 u32 reg; 1294 1295 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1296 1297 return reg & OMAP_I2C_SYSTEST_SDA_I_FUNC; 1298 } 1299 1300 static void omap_i2c_set_scl(struct i2c_adapter *adap, int val) 1301 { 1302 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1303 u32 reg; 1304 1305 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1306 if (val) 1307 reg |= OMAP_I2C_SYSTEST_SCL_O; 1308 else 1309 reg &= ~OMAP_I2C_SYSTEST_SCL_O; 1310 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1311 } 1312 1313 static void omap_i2c_prepare_recovery(struct i2c_adapter *adap) 1314 { 1315 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1316 u32 reg; 1317 1318 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1319 /* enable test mode */ 1320 reg |= OMAP_I2C_SYSTEST_ST_EN; 1321 /* select SDA/SCL IO mode */ 1322 reg |= 3 << OMAP_I2C_SYSTEST_TMODE_SHIFT; 1323 /* set SCL to high-impedance state (reset value is 0) */ 1324 reg |= OMAP_I2C_SYSTEST_SCL_O; 1325 /* set SDA to high-impedance state (reset value is 0) */ 1326 reg |= OMAP_I2C_SYSTEST_SDA_O; 1327 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1328 } 1329 1330 static void omap_i2c_unprepare_recovery(struct i2c_adapter *adap) 1331 { 1332 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1333 u32 reg; 1334 1335 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1336 /* restore reset values */ 1337 reg &= ~OMAP_I2C_SYSTEST_ST_EN; 1338 reg &= ~OMAP_I2C_SYSTEST_TMODE_MASK; 1339 reg &= ~OMAP_I2C_SYSTEST_SCL_O; 1340 reg &= ~OMAP_I2C_SYSTEST_SDA_O; 1341 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1342 } 1343 1344 static struct i2c_bus_recovery_info omap_i2c_bus_recovery_info = { 1345 .get_scl = omap_i2c_get_scl, 1346 .get_sda = omap_i2c_get_sda, 1347 .set_scl = omap_i2c_set_scl, 1348 .prepare_recovery = omap_i2c_prepare_recovery, 1349 .unprepare_recovery = omap_i2c_unprepare_recovery, 1350 .recover_bus = i2c_generic_scl_recovery, 1351 }; 1352 1353 static int 1354 omap_i2c_probe(struct platform_device *pdev) 1355 { 1356 struct omap_i2c_dev *omap; 1357 struct i2c_adapter *adap; 1358 const struct omap_i2c_bus_platform_data *pdata = 1359 dev_get_platdata(&pdev->dev); 1360 struct device_node *node = pdev->dev.of_node; 1361 const struct of_device_id *match; 1362 int irq; 1363 int r; 1364 u32 rev; 1365 u16 minor, major; 1366 1367 irq = platform_get_irq(pdev, 0); 1368 if (irq < 0) 1369 return irq; 1370 1371 omap = devm_kzalloc(&pdev->dev, sizeof(struct omap_i2c_dev), GFP_KERNEL); 1372 if (!omap) 1373 return -ENOMEM; 1374 1375 omap->base = devm_platform_ioremap_resource(pdev, 0); 1376 if (IS_ERR(omap->base)) 1377 return PTR_ERR(omap->base); 1378 1379 match = of_match_device(of_match_ptr(omap_i2c_of_match), &pdev->dev); 1380 if (match) { 1381 u32 freq = I2C_MAX_STANDARD_MODE_FREQ; 1382 1383 pdata = match->data; 1384 omap->flags = pdata->flags; 1385 1386 of_property_read_u32(node, "clock-frequency", &freq); 1387 /* convert DT freq value in Hz into kHz for speed */ 1388 omap->speed = freq / 1000; 1389 } else if (pdata != NULL) { 1390 omap->speed = pdata->clkrate; 1391 omap->flags = pdata->flags; 1392 omap->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat; 1393 } 1394 1395 omap->dev = &pdev->dev; 1396 omap->irq = irq; 1397 1398 platform_set_drvdata(pdev, omap); 1399 init_completion(&omap->cmd_complete); 1400 1401 omap->reg_shift = (omap->flags >> OMAP_I2C_FLAG_BUS_SHIFT__SHIFT) & 3; 1402 1403 pm_runtime_enable(omap->dev); 1404 pm_runtime_set_autosuspend_delay(omap->dev, OMAP_I2C_PM_TIMEOUT); 1405 pm_runtime_use_autosuspend(omap->dev); 1406 1407 r = pm_runtime_resume_and_get(omap->dev); 1408 if (r < 0) 1409 goto err_disable_pm; 1410 1411 /* 1412 * Read the Rev hi bit-[15:14] ie scheme this is 1 indicates ver2. 1413 * On omap1/3/2 Offset 4 is IE Reg the bit [15:14] is 0 at reset. 1414 * Also since the omap_i2c_read_reg uses reg_map_ip_* a 1415 * readw_relaxed is done. 1416 */ 1417 rev = readw_relaxed(omap->base + 0x04); 1418 1419 omap->scheme = OMAP_I2C_SCHEME(rev); 1420 switch (omap->scheme) { 1421 case OMAP_I2C_SCHEME_0: 1422 omap->regs = (u8 *)reg_map_ip_v1; 1423 omap->rev = omap_i2c_read_reg(omap, OMAP_I2C_REV_REG); 1424 minor = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev); 1425 major = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev); 1426 break; 1427 case OMAP_I2C_SCHEME_1: 1428 default: 1429 omap->regs = (u8 *)reg_map_ip_v2; 1430 rev = (rev << 16) | 1431 omap_i2c_read_reg(omap, OMAP_I2C_IP_V2_REVNB_LO); 1432 minor = OMAP_I2C_REV_SCHEME_1_MINOR(rev); 1433 major = OMAP_I2C_REV_SCHEME_1_MAJOR(rev); 1434 omap->rev = rev; 1435 } 1436 1437 omap->errata = 0; 1438 1439 if (omap->rev >= OMAP_I2C_REV_ON_2430 && 1440 omap->rev < OMAP_I2C_REV_ON_4430_PLUS) 1441 omap->errata |= I2C_OMAP_ERRATA_I207; 1442 1443 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530) 1444 omap->errata |= I2C_OMAP_ERRATA_I462; 1445 1446 if (!(omap->flags & OMAP_I2C_FLAG_NO_FIFO)) { 1447 u16 s; 1448 1449 /* Set up the fifo size - Get total size */ 1450 s = (omap_i2c_read_reg(omap, OMAP_I2C_BUFSTAT_REG) >> 14) & 0x3; 1451 omap->fifo_size = 0x8 << s; 1452 1453 /* 1454 * Set up notification threshold as half the total available 1455 * size. This is to ensure that we can handle the status on int 1456 * call back latencies. 1457 */ 1458 1459 omap->fifo_size = (omap->fifo_size / 2); 1460 1461 if (omap->rev < OMAP_I2C_REV_ON_3630) 1462 omap->b_hw = 1; /* Enable hardware fixes */ 1463 1464 /* calculate wakeup latency constraint for MPU */ 1465 if (omap->set_mpu_wkup_lat != NULL) 1466 omap->latency = (1000000 * omap->fifo_size) / 1467 (1000 * omap->speed / 8); 1468 } 1469 1470 /* reset ASAP, clearing any IRQs */ 1471 omap_i2c_init(omap); 1472 1473 if (omap->rev < OMAP_I2C_OMAP1_REV_2) 1474 r = devm_request_irq(&pdev->dev, omap->irq, omap_i2c_omap1_isr, 1475 IRQF_NO_SUSPEND, pdev->name, omap); 1476 else 1477 r = devm_request_threaded_irq(&pdev->dev, omap->irq, 1478 omap_i2c_isr, omap_i2c_isr_thread, 1479 IRQF_NO_SUSPEND | IRQF_ONESHOT, 1480 pdev->name, omap); 1481 1482 if (r) { 1483 dev_err(omap->dev, "failure requesting irq %i\n", omap->irq); 1484 goto err_unuse_clocks; 1485 } 1486 1487 adap = &omap->adapter; 1488 i2c_set_adapdata(adap, omap); 1489 adap->owner = THIS_MODULE; 1490 adap->class = I2C_CLASS_DEPRECATED; 1491 strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); 1492 adap->algo = &omap_i2c_algo; 1493 adap->quirks = &omap_i2c_quirks; 1494 adap->dev.parent = &pdev->dev; 1495 adap->dev.of_node = pdev->dev.of_node; 1496 adap->bus_recovery_info = &omap_i2c_bus_recovery_info; 1497 1498 /* i2c device drivers may be active on return from add_adapter() */ 1499 adap->nr = pdev->id; 1500 r = i2c_add_numbered_adapter(adap); 1501 if (r) 1502 goto err_unuse_clocks; 1503 1504 dev_info(omap->dev, "bus %d rev%d.%d at %d kHz\n", adap->nr, 1505 major, minor, omap->speed); 1506 1507 pm_runtime_mark_last_busy(omap->dev); 1508 pm_runtime_put_autosuspend(omap->dev); 1509 1510 return 0; 1511 1512 err_unuse_clocks: 1513 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 1514 pm_runtime_dont_use_autosuspend(omap->dev); 1515 pm_runtime_put_sync(omap->dev); 1516 err_disable_pm: 1517 pm_runtime_disable(&pdev->dev); 1518 1519 return r; 1520 } 1521 1522 static int omap_i2c_remove(struct platform_device *pdev) 1523 { 1524 struct omap_i2c_dev *omap = platform_get_drvdata(pdev); 1525 int ret; 1526 1527 i2c_del_adapter(&omap->adapter); 1528 ret = pm_runtime_resume_and_get(&pdev->dev); 1529 if (ret < 0) 1530 return ret; 1531 1532 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 1533 pm_runtime_dont_use_autosuspend(&pdev->dev); 1534 pm_runtime_put_sync(&pdev->dev); 1535 pm_runtime_disable(&pdev->dev); 1536 return 0; 1537 } 1538 1539 static int __maybe_unused omap_i2c_runtime_suspend(struct device *dev) 1540 { 1541 struct omap_i2c_dev *omap = dev_get_drvdata(dev); 1542 1543 omap->iestate = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1544 1545 if (omap->scheme == OMAP_I2C_SCHEME_0) 1546 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, 0); 1547 else 1548 omap_i2c_write_reg(omap, OMAP_I2C_IP_V2_IRQENABLE_CLR, 1549 OMAP_I2C_IP_V2_INTERRUPTS_MASK); 1550 1551 if (omap->rev < OMAP_I2C_OMAP1_REV_2) { 1552 omap_i2c_read_reg(omap, OMAP_I2C_IV_REG); /* Read clears */ 1553 } else { 1554 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, omap->iestate); 1555 1556 /* Flush posted write */ 1557 omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1558 } 1559 1560 pinctrl_pm_select_sleep_state(dev); 1561 1562 return 0; 1563 } 1564 1565 static int __maybe_unused omap_i2c_runtime_resume(struct device *dev) 1566 { 1567 struct omap_i2c_dev *omap = dev_get_drvdata(dev); 1568 1569 pinctrl_pm_select_default_state(dev); 1570 1571 if (!omap->regs) 1572 return 0; 1573 1574 __omap_i2c_init(omap); 1575 1576 return 0; 1577 } 1578 1579 static const struct dev_pm_ops omap_i2c_pm_ops = { 1580 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 1581 pm_runtime_force_resume) 1582 SET_RUNTIME_PM_OPS(omap_i2c_runtime_suspend, 1583 omap_i2c_runtime_resume, NULL) 1584 }; 1585 1586 static struct platform_driver omap_i2c_driver = { 1587 .probe = omap_i2c_probe, 1588 .remove = omap_i2c_remove, 1589 .driver = { 1590 .name = "omap_i2c", 1591 .pm = &omap_i2c_pm_ops, 1592 .of_match_table = of_match_ptr(omap_i2c_of_match), 1593 }, 1594 }; 1595 1596 /* I2C may be needed to bring up other drivers */ 1597 static int __init 1598 omap_i2c_init_driver(void) 1599 { 1600 return platform_driver_register(&omap_i2c_driver); 1601 } 1602 subsys_initcall(omap_i2c_init_driver); 1603 1604 static void __exit omap_i2c_exit_driver(void) 1605 { 1606 platform_driver_unregister(&omap_i2c_driver); 1607 } 1608 module_exit(omap_i2c_exit_driver); 1609 1610 MODULE_AUTHOR("MontaVista Software, Inc. (and others)"); 1611 MODULE_DESCRIPTION("TI OMAP I2C bus adapter"); 1612 MODULE_LICENSE("GPL"); 1613 MODULE_ALIAS("platform:omap_i2c"); 1614