1 /* 2 * TI OMAP I2C master mode driver 3 * 4 * Copyright (C) 2003 MontaVista Software, Inc. 5 * Copyright (C) 2005 Nokia Corporation 6 * Copyright (C) 2004 - 2007 Texas Instruments. 7 * 8 * Originally written by MontaVista Software, Inc. 9 * Additional contributions by: 10 * Tony Lindgren <tony@atomide.com> 11 * Imre Deak <imre.deak@nokia.com> 12 * Juha Yrjölä <juha.yrjola@solidboot.com> 13 * Syed Khasim <x0khasim@ti.com> 14 * Nishant Menon <nm@ti.com> 15 * 16 * This program is free software; you can redistribute it and/or modify 17 * it under the terms of the GNU General Public License as published by 18 * the Free Software Foundation; either version 2 of the License, or 19 * (at your option) any later version. 20 * 21 * This program is distributed in the hope that it will be useful, 22 * but WITHOUT ANY WARRANTY; without even the implied warranty of 23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 24 * GNU General Public License for more details. 25 */ 26 27 #include <linux/module.h> 28 #include <linux/delay.h> 29 #include <linux/i2c.h> 30 #include <linux/err.h> 31 #include <linux/interrupt.h> 32 #include <linux/completion.h> 33 #include <linux/platform_device.h> 34 #include <linux/clk.h> 35 #include <linux/io.h> 36 #include <linux/of.h> 37 #include <linux/of_device.h> 38 #include <linux/slab.h> 39 #include <linux/i2c-omap.h> 40 #include <linux/pm_runtime.h> 41 #include <linux/pinctrl/consumer.h> 42 43 /* I2C controller revisions */ 44 #define OMAP_I2C_OMAP1_REV_2 0x20 45 46 /* I2C controller revisions present on specific hardware */ 47 #define OMAP_I2C_REV_ON_2430 0x00000036 48 #define OMAP_I2C_REV_ON_3430_3530 0x0000003C 49 #define OMAP_I2C_REV_ON_3630 0x00000040 50 #define OMAP_I2C_REV_ON_4430_PLUS 0x50400002 51 52 /* timeout waiting for the controller to respond */ 53 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000)) 54 55 /* timeout for pm runtime autosuspend */ 56 #define OMAP_I2C_PM_TIMEOUT 1000 /* ms */ 57 58 /* timeout for making decision on bus free status */ 59 #define OMAP_I2C_BUS_FREE_TIMEOUT (msecs_to_jiffies(10)) 60 61 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */ 62 enum { 63 OMAP_I2C_REV_REG = 0, 64 OMAP_I2C_IE_REG, 65 OMAP_I2C_STAT_REG, 66 OMAP_I2C_IV_REG, 67 OMAP_I2C_WE_REG, 68 OMAP_I2C_SYSS_REG, 69 OMAP_I2C_BUF_REG, 70 OMAP_I2C_CNT_REG, 71 OMAP_I2C_DATA_REG, 72 OMAP_I2C_SYSC_REG, 73 OMAP_I2C_CON_REG, 74 OMAP_I2C_OA_REG, 75 OMAP_I2C_SA_REG, 76 OMAP_I2C_PSC_REG, 77 OMAP_I2C_SCLL_REG, 78 OMAP_I2C_SCLH_REG, 79 OMAP_I2C_SYSTEST_REG, 80 OMAP_I2C_BUFSTAT_REG, 81 /* only on OMAP4430 */ 82 OMAP_I2C_IP_V2_REVNB_LO, 83 OMAP_I2C_IP_V2_REVNB_HI, 84 OMAP_I2C_IP_V2_IRQSTATUS_RAW, 85 OMAP_I2C_IP_V2_IRQENABLE_SET, 86 OMAP_I2C_IP_V2_IRQENABLE_CLR, 87 }; 88 89 /* I2C Interrupt Enable Register (OMAP_I2C_IE): */ 90 #define OMAP_I2C_IE_XDR (1 << 14) /* TX Buffer drain int enable */ 91 #define OMAP_I2C_IE_RDR (1 << 13) /* RX Buffer drain int enable */ 92 #define OMAP_I2C_IE_XRDY (1 << 4) /* TX data ready int enable */ 93 #define OMAP_I2C_IE_RRDY (1 << 3) /* RX data ready int enable */ 94 #define OMAP_I2C_IE_ARDY (1 << 2) /* Access ready int enable */ 95 #define OMAP_I2C_IE_NACK (1 << 1) /* No ack interrupt enable */ 96 #define OMAP_I2C_IE_AL (1 << 0) /* Arbitration lost int ena */ 97 98 /* I2C Status Register (OMAP_I2C_STAT): */ 99 #define OMAP_I2C_STAT_XDR (1 << 14) /* TX Buffer draining */ 100 #define OMAP_I2C_STAT_RDR (1 << 13) /* RX Buffer draining */ 101 #define OMAP_I2C_STAT_BB (1 << 12) /* Bus busy */ 102 #define OMAP_I2C_STAT_ROVR (1 << 11) /* Receive overrun */ 103 #define OMAP_I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ 104 #define OMAP_I2C_STAT_AAS (1 << 9) /* Address as slave */ 105 #define OMAP_I2C_STAT_BF (1 << 8) /* Bus Free */ 106 #define OMAP_I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ 107 #define OMAP_I2C_STAT_RRDY (1 << 3) /* Receive data ready */ 108 #define OMAP_I2C_STAT_ARDY (1 << 2) /* Register access ready */ 109 #define OMAP_I2C_STAT_NACK (1 << 1) /* No ack interrupt enable */ 110 #define OMAP_I2C_STAT_AL (1 << 0) /* Arbitration lost int ena */ 111 112 /* I2C WE wakeup enable register */ 113 #define OMAP_I2C_WE_XDR_WE (1 << 14) /* TX drain wakup */ 114 #define OMAP_I2C_WE_RDR_WE (1 << 13) /* RX drain wakeup */ 115 #define OMAP_I2C_WE_AAS_WE (1 << 9) /* Address as slave wakeup*/ 116 #define OMAP_I2C_WE_BF_WE (1 << 8) /* Bus free wakeup */ 117 #define OMAP_I2C_WE_STC_WE (1 << 6) /* Start condition wakeup */ 118 #define OMAP_I2C_WE_GC_WE (1 << 5) /* General call wakeup */ 119 #define OMAP_I2C_WE_DRDY_WE (1 << 3) /* TX/RX data ready wakeup */ 120 #define OMAP_I2C_WE_ARDY_WE (1 << 2) /* Reg access ready wakeup */ 121 #define OMAP_I2C_WE_NACK_WE (1 << 1) /* No acknowledgment wakeup */ 122 #define OMAP_I2C_WE_AL_WE (1 << 0) /* Arbitration lost wakeup */ 123 124 #define OMAP_I2C_WE_ALL (OMAP_I2C_WE_XDR_WE | OMAP_I2C_WE_RDR_WE | \ 125 OMAP_I2C_WE_AAS_WE | OMAP_I2C_WE_BF_WE | \ 126 OMAP_I2C_WE_STC_WE | OMAP_I2C_WE_GC_WE | \ 127 OMAP_I2C_WE_DRDY_WE | OMAP_I2C_WE_ARDY_WE | \ 128 OMAP_I2C_WE_NACK_WE | OMAP_I2C_WE_AL_WE) 129 130 /* I2C Buffer Configuration Register (OMAP_I2C_BUF): */ 131 #define OMAP_I2C_BUF_RDMA_EN (1 << 15) /* RX DMA channel enable */ 132 #define OMAP_I2C_BUF_RXFIF_CLR (1 << 14) /* RX FIFO Clear */ 133 #define OMAP_I2C_BUF_XDMA_EN (1 << 7) /* TX DMA channel enable */ 134 #define OMAP_I2C_BUF_TXFIF_CLR (1 << 6) /* TX FIFO Clear */ 135 136 /* I2C Configuration Register (OMAP_I2C_CON): */ 137 #define OMAP_I2C_CON_EN (1 << 15) /* I2C module enable */ 138 #define OMAP_I2C_CON_BE (1 << 14) /* Big endian mode */ 139 #define OMAP_I2C_CON_OPMODE_HS (1 << 12) /* High Speed support */ 140 #define OMAP_I2C_CON_STB (1 << 11) /* Start byte mode (master) */ 141 #define OMAP_I2C_CON_MST (1 << 10) /* Master/slave mode */ 142 #define OMAP_I2C_CON_TRX (1 << 9) /* TX/RX mode (master only) */ 143 #define OMAP_I2C_CON_XA (1 << 8) /* Expand address */ 144 #define OMAP_I2C_CON_RM (1 << 2) /* Repeat mode (master only) */ 145 #define OMAP_I2C_CON_STP (1 << 1) /* Stop cond (master only) */ 146 #define OMAP_I2C_CON_STT (1 << 0) /* Start condition (master) */ 147 148 /* I2C SCL time value when Master */ 149 #define OMAP_I2C_SCLL_HSSCLL 8 150 #define OMAP_I2C_SCLH_HSSCLH 8 151 152 /* I2C System Test Register (OMAP_I2C_SYSTEST): */ 153 #define OMAP_I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ 154 #define OMAP_I2C_SYSTEST_FREE (1 << 14) /* Free running mode */ 155 #define OMAP_I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ 156 #define OMAP_I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ 157 /* Functional mode */ 158 #define OMAP_I2C_SYSTEST_SCL_I_FUNC (1 << 8) /* SCL line input value */ 159 #define OMAP_I2C_SYSTEST_SCL_O_FUNC (1 << 7) /* SCL line output value */ 160 #define OMAP_I2C_SYSTEST_SDA_I_FUNC (1 << 6) /* SDA line input value */ 161 #define OMAP_I2C_SYSTEST_SDA_O_FUNC (1 << 5) /* SDA line output value */ 162 /* SDA/SCL IO mode */ 163 #define OMAP_I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense in */ 164 #define OMAP_I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive out */ 165 #define OMAP_I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense in */ 166 #define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */ 167 168 /* OCP_SYSSTATUS bit definitions */ 169 #define SYSS_RESETDONE_MASK (1 << 0) 170 171 /* OCP_SYSCONFIG bit definitions */ 172 #define SYSC_CLOCKACTIVITY_MASK (0x3 << 8) 173 #define SYSC_SIDLEMODE_MASK (0x3 << 3) 174 #define SYSC_ENAWAKEUP_MASK (1 << 2) 175 #define SYSC_SOFTRESET_MASK (1 << 1) 176 #define SYSC_AUTOIDLE_MASK (1 << 0) 177 178 #define SYSC_IDLEMODE_SMART 0x2 179 #define SYSC_CLOCKACTIVITY_FCLK 0x2 180 181 /* Errata definitions */ 182 #define I2C_OMAP_ERRATA_I207 (1 << 0) 183 #define I2C_OMAP_ERRATA_I462 (1 << 1) 184 185 #define OMAP_I2C_IP_V2_INTERRUPTS_MASK 0x6FFF 186 187 struct omap_i2c_dev { 188 struct device *dev; 189 void __iomem *base; /* virtual */ 190 int irq; 191 int reg_shift; /* bit shift for I2C register addresses */ 192 struct completion cmd_complete; 193 struct resource *ioarea; 194 u32 latency; /* maximum mpu wkup latency */ 195 void (*set_mpu_wkup_lat)(struct device *dev, 196 long latency); 197 u32 speed; /* Speed of bus in kHz */ 198 u32 flags; 199 u16 scheme; 200 u16 cmd_err; 201 u8 *buf; 202 u8 *regs; 203 size_t buf_len; 204 struct i2c_adapter adapter; 205 u8 threshold; 206 u8 fifo_size; /* use as flag and value 207 * fifo_size==0 implies no fifo 208 * if set, should be trsh+1 209 */ 210 u32 rev; 211 unsigned b_hw:1; /* bad h/w fixes */ 212 unsigned bb_valid:1; /* true when BB-bit reflects 213 * the I2C bus state 214 */ 215 unsigned receiver:1; /* true when we're in receiver mode */ 216 u16 iestate; /* Saved interrupt register */ 217 u16 pscstate; 218 u16 scllstate; 219 u16 sclhstate; 220 u16 syscstate; 221 u16 westate; 222 u16 errata; 223 }; 224 225 static const u8 reg_map_ip_v1[] = { 226 [OMAP_I2C_REV_REG] = 0x00, 227 [OMAP_I2C_IE_REG] = 0x01, 228 [OMAP_I2C_STAT_REG] = 0x02, 229 [OMAP_I2C_IV_REG] = 0x03, 230 [OMAP_I2C_WE_REG] = 0x03, 231 [OMAP_I2C_SYSS_REG] = 0x04, 232 [OMAP_I2C_BUF_REG] = 0x05, 233 [OMAP_I2C_CNT_REG] = 0x06, 234 [OMAP_I2C_DATA_REG] = 0x07, 235 [OMAP_I2C_SYSC_REG] = 0x08, 236 [OMAP_I2C_CON_REG] = 0x09, 237 [OMAP_I2C_OA_REG] = 0x0a, 238 [OMAP_I2C_SA_REG] = 0x0b, 239 [OMAP_I2C_PSC_REG] = 0x0c, 240 [OMAP_I2C_SCLL_REG] = 0x0d, 241 [OMAP_I2C_SCLH_REG] = 0x0e, 242 [OMAP_I2C_SYSTEST_REG] = 0x0f, 243 [OMAP_I2C_BUFSTAT_REG] = 0x10, 244 }; 245 246 static const u8 reg_map_ip_v2[] = { 247 [OMAP_I2C_REV_REG] = 0x04, 248 [OMAP_I2C_IE_REG] = 0x2c, 249 [OMAP_I2C_STAT_REG] = 0x28, 250 [OMAP_I2C_IV_REG] = 0x34, 251 [OMAP_I2C_WE_REG] = 0x34, 252 [OMAP_I2C_SYSS_REG] = 0x90, 253 [OMAP_I2C_BUF_REG] = 0x94, 254 [OMAP_I2C_CNT_REG] = 0x98, 255 [OMAP_I2C_DATA_REG] = 0x9c, 256 [OMAP_I2C_SYSC_REG] = 0x10, 257 [OMAP_I2C_CON_REG] = 0xa4, 258 [OMAP_I2C_OA_REG] = 0xa8, 259 [OMAP_I2C_SA_REG] = 0xac, 260 [OMAP_I2C_PSC_REG] = 0xb0, 261 [OMAP_I2C_SCLL_REG] = 0xb4, 262 [OMAP_I2C_SCLH_REG] = 0xb8, 263 [OMAP_I2C_SYSTEST_REG] = 0xbC, 264 [OMAP_I2C_BUFSTAT_REG] = 0xc0, 265 [OMAP_I2C_IP_V2_REVNB_LO] = 0x00, 266 [OMAP_I2C_IP_V2_REVNB_HI] = 0x04, 267 [OMAP_I2C_IP_V2_IRQSTATUS_RAW] = 0x24, 268 [OMAP_I2C_IP_V2_IRQENABLE_SET] = 0x2c, 269 [OMAP_I2C_IP_V2_IRQENABLE_CLR] = 0x30, 270 }; 271 272 static inline void omap_i2c_write_reg(struct omap_i2c_dev *omap, 273 int reg, u16 val) 274 { 275 writew_relaxed(val, omap->base + 276 (omap->regs[reg] << omap->reg_shift)); 277 } 278 279 static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *omap, int reg) 280 { 281 return readw_relaxed(omap->base + 282 (omap->regs[reg] << omap->reg_shift)); 283 } 284 285 static void __omap_i2c_init(struct omap_i2c_dev *omap) 286 { 287 288 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 289 290 /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */ 291 omap_i2c_write_reg(omap, OMAP_I2C_PSC_REG, omap->pscstate); 292 293 /* SCL low and high time values */ 294 omap_i2c_write_reg(omap, OMAP_I2C_SCLL_REG, omap->scllstate); 295 omap_i2c_write_reg(omap, OMAP_I2C_SCLH_REG, omap->sclhstate); 296 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) 297 omap_i2c_write_reg(omap, OMAP_I2C_WE_REG, omap->westate); 298 299 /* Take the I2C module out of reset: */ 300 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); 301 302 /* 303 * NOTE: right after setting CON_EN, STAT_BB could be 0 while the 304 * bus is busy. It will be changed to 1 on the next IP FCLK clock. 305 * udelay(1) will be enough to fix that. 306 */ 307 308 /* 309 * Don't write to this register if the IE state is 0 as it can 310 * cause deadlock. 311 */ 312 if (omap->iestate) 313 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, omap->iestate); 314 } 315 316 static int omap_i2c_reset(struct omap_i2c_dev *omap) 317 { 318 unsigned long timeout; 319 u16 sysc; 320 321 if (omap->rev >= OMAP_I2C_OMAP1_REV_2) { 322 sysc = omap_i2c_read_reg(omap, OMAP_I2C_SYSC_REG); 323 324 /* Disable I2C controller before soft reset */ 325 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 326 omap_i2c_read_reg(omap, OMAP_I2C_CON_REG) & 327 ~(OMAP_I2C_CON_EN)); 328 329 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, SYSC_SOFTRESET_MASK); 330 /* For some reason we need to set the EN bit before the 331 * reset done bit gets set. */ 332 timeout = jiffies + OMAP_I2C_TIMEOUT; 333 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); 334 while (!(omap_i2c_read_reg(omap, OMAP_I2C_SYSS_REG) & 335 SYSS_RESETDONE_MASK)) { 336 if (time_after(jiffies, timeout)) { 337 dev_warn(omap->dev, "timeout waiting " 338 "for controller reset\n"); 339 return -ETIMEDOUT; 340 } 341 msleep(1); 342 } 343 344 /* SYSC register is cleared by the reset; rewrite it */ 345 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, sysc); 346 347 if (omap->rev > OMAP_I2C_REV_ON_3430_3530) { 348 /* Schedule I2C-bus monitoring on the next transfer */ 349 omap->bb_valid = 0; 350 } 351 } 352 353 return 0; 354 } 355 356 static int omap_i2c_init(struct omap_i2c_dev *omap) 357 { 358 u16 psc = 0, scll = 0, sclh = 0; 359 u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0; 360 unsigned long fclk_rate = 12000000; 361 unsigned long internal_clk = 0; 362 struct clk *fclk; 363 int error; 364 365 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) { 366 /* 367 * Enabling all wakup sources to stop I2C freezing on 368 * WFI instruction. 369 * REVISIT: Some wkup sources might not be needed. 370 */ 371 omap->westate = OMAP_I2C_WE_ALL; 372 } 373 374 if (omap->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) { 375 /* 376 * The I2C functional clock is the armxor_ck, so there's 377 * no need to get "armxor_ck" separately. Now, if OMAP2420 378 * always returns 12MHz for the functional clock, we can 379 * do this bit unconditionally. 380 */ 381 fclk = clk_get(omap->dev, "fck"); 382 if (IS_ERR(fclk)) { 383 error = PTR_ERR(fclk); 384 dev_err(omap->dev, "could not get fck: %i\n", error); 385 386 return error; 387 } 388 389 fclk_rate = clk_get_rate(fclk); 390 clk_put(fclk); 391 392 /* TRM for 5912 says the I2C clock must be prescaled to be 393 * between 7 - 12 MHz. The XOR input clock is typically 394 * 12, 13 or 19.2 MHz. So we should have code that produces: 395 * 396 * XOR MHz Divider Prescaler 397 * 12 1 0 398 * 13 2 1 399 * 19.2 2 1 400 */ 401 if (fclk_rate > 12000000) 402 psc = fclk_rate / 12000000; 403 } 404 405 if (!(omap->flags & OMAP_I2C_FLAG_SIMPLE_CLOCK)) { 406 407 /* 408 * HSI2C controller internal clk rate should be 19.2 Mhz for 409 * HS and for all modes on 2430. On 34xx we can use lower rate 410 * to get longer filter period for better noise suppression. 411 * The filter is iclk (fclk for HS) period. 412 */ 413 if (omap->speed > 400 || 414 omap->flags & OMAP_I2C_FLAG_FORCE_19200_INT_CLK) 415 internal_clk = 19200; 416 else if (omap->speed > 100) 417 internal_clk = 9600; 418 else 419 internal_clk = 4000; 420 fclk = clk_get(omap->dev, "fck"); 421 if (IS_ERR(fclk)) { 422 error = PTR_ERR(fclk); 423 dev_err(omap->dev, "could not get fck: %i\n", error); 424 425 return error; 426 } 427 fclk_rate = clk_get_rate(fclk) / 1000; 428 clk_put(fclk); 429 430 /* Compute prescaler divisor */ 431 psc = fclk_rate / internal_clk; 432 psc = psc - 1; 433 434 /* If configured for High Speed */ 435 if (omap->speed > 400) { 436 unsigned long scl; 437 438 /* For first phase of HS mode */ 439 scl = internal_clk / 400; 440 fsscll = scl - (scl / 3) - 7; 441 fssclh = (scl / 3) - 5; 442 443 /* For second phase of HS mode */ 444 scl = fclk_rate / omap->speed; 445 hsscll = scl - (scl / 3) - 7; 446 hssclh = (scl / 3) - 5; 447 } else if (omap->speed > 100) { 448 unsigned long scl; 449 450 /* Fast mode */ 451 scl = internal_clk / omap->speed; 452 fsscll = scl - (scl / 3) - 7; 453 fssclh = (scl / 3) - 5; 454 } else { 455 /* Standard mode */ 456 fsscll = internal_clk / (omap->speed * 2) - 7; 457 fssclh = internal_clk / (omap->speed * 2) - 5; 458 } 459 scll = (hsscll << OMAP_I2C_SCLL_HSSCLL) | fsscll; 460 sclh = (hssclh << OMAP_I2C_SCLH_HSSCLH) | fssclh; 461 } else { 462 /* Program desired operating rate */ 463 fclk_rate /= (psc + 1) * 1000; 464 if (psc > 2) 465 psc = 2; 466 scll = fclk_rate / (omap->speed * 2) - 7 + psc; 467 sclh = fclk_rate / (omap->speed * 2) - 7 + psc; 468 } 469 470 omap->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY | 471 OMAP_I2C_IE_ARDY | OMAP_I2C_IE_NACK | 472 OMAP_I2C_IE_AL) | ((omap->fifo_size) ? 473 (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0); 474 475 omap->pscstate = psc; 476 omap->scllstate = scll; 477 omap->sclhstate = sclh; 478 479 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530) { 480 /* Not implemented */ 481 omap->bb_valid = 1; 482 } 483 484 __omap_i2c_init(omap); 485 486 return 0; 487 } 488 489 /* 490 * Try bus recovery, but only if SDA is actually low. 491 */ 492 static int omap_i2c_recover_bus(struct omap_i2c_dev *omap) 493 { 494 u16 systest; 495 496 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG); 497 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) && 498 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC)) 499 return 0; /* bus seems to already be fine */ 500 if (!(systest & OMAP_I2C_SYSTEST_SCL_I_FUNC)) 501 return -EBUSY; /* recovery would not fix SCL */ 502 return i2c_recover_bus(&omap->adapter); 503 } 504 505 /* 506 * Waiting on Bus Busy 507 */ 508 static int omap_i2c_wait_for_bb(struct omap_i2c_dev *omap) 509 { 510 unsigned long timeout; 511 512 timeout = jiffies + OMAP_I2C_TIMEOUT; 513 while (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) & OMAP_I2C_STAT_BB) { 514 if (time_after(jiffies, timeout)) 515 return omap_i2c_recover_bus(omap); 516 msleep(1); 517 } 518 519 return 0; 520 } 521 522 /* 523 * Wait while BB-bit doesn't reflect the I2C bus state 524 * 525 * In a multimaster environment, after IP software reset, BB-bit value doesn't 526 * correspond to the current bus state. It may happen what BB-bit will be 0, 527 * while the bus is busy due to another I2C master activity. 528 * Here are BB-bit values after reset: 529 * SDA SCL BB NOTES 530 * 0 0 0 1, 2 531 * 1 0 0 1, 2 532 * 0 1 1 533 * 1 1 0 3 534 * Later, if IP detect SDA=0 and SCL=1 (ACK) or SDA 1->0 while SCL=1 (START) 535 * combinations on the bus, it set BB-bit to 1. 536 * If IP detect SDA 0->1 while SCL=1 (STOP) combination on the bus, 537 * it set BB-bit to 0 and BF to 1. 538 * BB and BF bits correctly tracks the bus state while IP is suspended 539 * BB bit became valid on the next FCLK clock after CON_EN bit set 540 * 541 * NOTES: 542 * 1. Any transfer started when BB=0 and bus is busy wouldn't be 543 * completed by IP and results in controller timeout. 544 * 2. Any transfer started when BB=0 and SCL=0 results in IP 545 * starting to drive SDA low. In that case IP corrupt data 546 * on the bus. 547 * 3. Any transfer started in the middle of another master's transfer 548 * results in unpredictable results and data corruption 549 */ 550 static int omap_i2c_wait_for_bb_valid(struct omap_i2c_dev *omap) 551 { 552 unsigned long bus_free_timeout = 0; 553 unsigned long timeout; 554 int bus_free = 0; 555 u16 stat, systest; 556 557 if (omap->bb_valid) 558 return 0; 559 560 timeout = jiffies + OMAP_I2C_TIMEOUT; 561 while (1) { 562 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 563 /* 564 * We will see BB or BF event in a case IP had detected any 565 * activity on the I2C bus. Now IP correctly tracks the bus 566 * state. BB-bit value is valid. 567 */ 568 if (stat & (OMAP_I2C_STAT_BB | OMAP_I2C_STAT_BF)) 569 break; 570 571 /* 572 * Otherwise, we must look signals on the bus to make 573 * the right decision. 574 */ 575 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG); 576 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) && 577 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC)) { 578 if (!bus_free) { 579 bus_free_timeout = jiffies + 580 OMAP_I2C_BUS_FREE_TIMEOUT; 581 bus_free = 1; 582 } 583 584 /* 585 * SDA and SCL lines was high for 10 ms without bus 586 * activity detected. The bus is free. Consider 587 * BB-bit value is valid. 588 */ 589 if (time_after(jiffies, bus_free_timeout)) 590 break; 591 } else { 592 bus_free = 0; 593 } 594 595 if (time_after(jiffies, timeout)) { 596 /* 597 * SDA or SCL were low for the entire timeout without 598 * any activity detected. Most likely, a slave is 599 * locking up the bus with no master driving the clock. 600 */ 601 dev_warn(omap->dev, "timeout waiting for bus ready\n"); 602 return omap_i2c_recover_bus(omap); 603 } 604 605 msleep(1); 606 } 607 608 omap->bb_valid = 1; 609 return 0; 610 } 611 612 static void omap_i2c_resize_fifo(struct omap_i2c_dev *omap, u8 size, bool is_rx) 613 { 614 u16 buf; 615 616 if (omap->flags & OMAP_I2C_FLAG_NO_FIFO) 617 return; 618 619 /* 620 * Set up notification threshold based on message size. We're doing 621 * this to try and avoid draining feature as much as possible. Whenever 622 * we have big messages to transfer (bigger than our total fifo size) 623 * then we might use draining feature to transfer the remaining bytes. 624 */ 625 626 omap->threshold = clamp(size, (u8) 1, omap->fifo_size); 627 628 buf = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG); 629 630 if (is_rx) { 631 /* Clear RX Threshold */ 632 buf &= ~(0x3f << 8); 633 buf |= ((omap->threshold - 1) << 8) | OMAP_I2C_BUF_RXFIF_CLR; 634 } else { 635 /* Clear TX Threshold */ 636 buf &= ~0x3f; 637 buf |= (omap->threshold - 1) | OMAP_I2C_BUF_TXFIF_CLR; 638 } 639 640 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, buf); 641 642 if (omap->rev < OMAP_I2C_REV_ON_3630) 643 omap->b_hw = 1; /* Enable hardware fixes */ 644 645 /* calculate wakeup latency constraint for MPU */ 646 if (omap->set_mpu_wkup_lat != NULL) 647 omap->latency = (1000000 * omap->threshold) / 648 (1000 * omap->speed / 8); 649 } 650 651 /* 652 * Low level master read/write transaction. 653 */ 654 static int omap_i2c_xfer_msg(struct i2c_adapter *adap, 655 struct i2c_msg *msg, int stop) 656 { 657 struct omap_i2c_dev *omap = i2c_get_adapdata(adap); 658 unsigned long timeout; 659 u16 w; 660 661 dev_dbg(omap->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n", 662 msg->addr, msg->len, msg->flags, stop); 663 664 if (msg->len == 0) 665 return -EINVAL; 666 667 omap->receiver = !!(msg->flags & I2C_M_RD); 668 omap_i2c_resize_fifo(omap, msg->len, omap->receiver); 669 670 omap_i2c_write_reg(omap, OMAP_I2C_SA_REG, msg->addr); 671 672 /* REVISIT: Could the STB bit of I2C_CON be used with probing? */ 673 omap->buf = msg->buf; 674 omap->buf_len = msg->len; 675 676 /* make sure writes to omap->buf_len are ordered */ 677 barrier(); 678 679 omap_i2c_write_reg(omap, OMAP_I2C_CNT_REG, omap->buf_len); 680 681 /* Clear the FIFO Buffers */ 682 w = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG); 683 w |= OMAP_I2C_BUF_RXFIF_CLR | OMAP_I2C_BUF_TXFIF_CLR; 684 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, w); 685 686 reinit_completion(&omap->cmd_complete); 687 omap->cmd_err = 0; 688 689 w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT; 690 691 /* High speed configuration */ 692 if (omap->speed > 400) 693 w |= OMAP_I2C_CON_OPMODE_HS; 694 695 if (msg->flags & I2C_M_STOP) 696 stop = 1; 697 if (msg->flags & I2C_M_TEN) 698 w |= OMAP_I2C_CON_XA; 699 if (!(msg->flags & I2C_M_RD)) 700 w |= OMAP_I2C_CON_TRX; 701 702 if (!omap->b_hw && stop) 703 w |= OMAP_I2C_CON_STP; 704 /* 705 * NOTE: STAT_BB bit could became 1 here if another master occupy 706 * the bus. IP successfully complete transfer when the bus will be 707 * free again (BB reset to 0). 708 */ 709 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 710 711 /* 712 * Don't write stt and stp together on some hardware. 713 */ 714 if (omap->b_hw && stop) { 715 unsigned long delay = jiffies + OMAP_I2C_TIMEOUT; 716 u16 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 717 while (con & OMAP_I2C_CON_STT) { 718 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 719 720 /* Let the user know if i2c is in a bad state */ 721 if (time_after(jiffies, delay)) { 722 dev_err(omap->dev, "controller timed out " 723 "waiting for start condition to finish\n"); 724 return -ETIMEDOUT; 725 } 726 cpu_relax(); 727 } 728 729 w |= OMAP_I2C_CON_STP; 730 w &= ~OMAP_I2C_CON_STT; 731 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 732 } 733 734 /* 735 * REVISIT: We should abort the transfer on signals, but the bus goes 736 * into arbitration and we're currently unable to recover from it. 737 */ 738 timeout = wait_for_completion_timeout(&omap->cmd_complete, 739 OMAP_I2C_TIMEOUT); 740 if (timeout == 0) { 741 dev_err(omap->dev, "controller timed out\n"); 742 omap_i2c_reset(omap); 743 __omap_i2c_init(omap); 744 return -ETIMEDOUT; 745 } 746 747 if (likely(!omap->cmd_err)) 748 return 0; 749 750 /* We have an error */ 751 if (omap->cmd_err & (OMAP_I2C_STAT_ROVR | OMAP_I2C_STAT_XUDF)) { 752 omap_i2c_reset(omap); 753 __omap_i2c_init(omap); 754 return -EIO; 755 } 756 757 if (omap->cmd_err & OMAP_I2C_STAT_AL) 758 return -EAGAIN; 759 760 if (omap->cmd_err & OMAP_I2C_STAT_NACK) { 761 if (msg->flags & I2C_M_IGNORE_NAK) 762 return 0; 763 764 w = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG); 765 w |= OMAP_I2C_CON_STP; 766 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w); 767 return -EREMOTEIO; 768 } 769 return -EIO; 770 } 771 772 773 /* 774 * Prepare controller for a transaction and call omap_i2c_xfer_msg 775 * to do the work during IRQ processing. 776 */ 777 static int 778 omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) 779 { 780 struct omap_i2c_dev *omap = i2c_get_adapdata(adap); 781 int i; 782 int r; 783 784 r = pm_runtime_get_sync(omap->dev); 785 if (r < 0) 786 goto out; 787 788 r = omap_i2c_wait_for_bb_valid(omap); 789 if (r < 0) 790 goto out; 791 792 r = omap_i2c_wait_for_bb(omap); 793 if (r < 0) 794 goto out; 795 796 if (omap->set_mpu_wkup_lat != NULL) 797 omap->set_mpu_wkup_lat(omap->dev, omap->latency); 798 799 for (i = 0; i < num; i++) { 800 r = omap_i2c_xfer_msg(adap, &msgs[i], (i == (num - 1))); 801 if (r != 0) 802 break; 803 } 804 805 if (r == 0) 806 r = num; 807 808 omap_i2c_wait_for_bb(omap); 809 810 if (omap->set_mpu_wkup_lat != NULL) 811 omap->set_mpu_wkup_lat(omap->dev, -1); 812 813 out: 814 pm_runtime_mark_last_busy(omap->dev); 815 pm_runtime_put_autosuspend(omap->dev); 816 return r; 817 } 818 819 static u32 820 omap_i2c_func(struct i2c_adapter *adap) 821 { 822 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | 823 I2C_FUNC_PROTOCOL_MANGLING; 824 } 825 826 static inline void 827 omap_i2c_complete_cmd(struct omap_i2c_dev *omap, u16 err) 828 { 829 omap->cmd_err |= err; 830 complete(&omap->cmd_complete); 831 } 832 833 static inline void 834 omap_i2c_ack_stat(struct omap_i2c_dev *omap, u16 stat) 835 { 836 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, stat); 837 } 838 839 static inline void i2c_omap_errata_i207(struct omap_i2c_dev *omap, u16 stat) 840 { 841 /* 842 * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8) 843 * Not applicable for OMAP4. 844 * Under certain rare conditions, RDR could be set again 845 * when the bus is busy, then ignore the interrupt and 846 * clear the interrupt. 847 */ 848 if (stat & OMAP_I2C_STAT_RDR) { 849 /* Step 1: If RDR is set, clear it */ 850 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 851 852 /* Step 2: */ 853 if (!(omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) 854 & OMAP_I2C_STAT_BB)) { 855 856 /* Step 3: */ 857 if (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) 858 & OMAP_I2C_STAT_RDR) { 859 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 860 dev_dbg(omap->dev, "RDR when bus is busy.\n"); 861 } 862 863 } 864 } 865 } 866 867 /* rev1 devices are apparently only on some 15xx */ 868 #ifdef CONFIG_ARCH_OMAP15XX 869 870 static irqreturn_t 871 omap_i2c_omap1_isr(int this_irq, void *dev_id) 872 { 873 struct omap_i2c_dev *omap = dev_id; 874 u16 iv, w; 875 876 if (pm_runtime_suspended(omap->dev)) 877 return IRQ_NONE; 878 879 iv = omap_i2c_read_reg(omap, OMAP_I2C_IV_REG); 880 switch (iv) { 881 case 0x00: /* None */ 882 break; 883 case 0x01: /* Arbitration lost */ 884 dev_err(omap->dev, "Arbitration lost\n"); 885 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_AL); 886 break; 887 case 0x02: /* No acknowledgement */ 888 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_NACK); 889 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_STP); 890 break; 891 case 0x03: /* Register access ready */ 892 omap_i2c_complete_cmd(omap, 0); 893 break; 894 case 0x04: /* Receive data ready */ 895 if (omap->buf_len) { 896 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG); 897 *omap->buf++ = w; 898 omap->buf_len--; 899 if (omap->buf_len) { 900 *omap->buf++ = w >> 8; 901 omap->buf_len--; 902 } 903 } else 904 dev_err(omap->dev, "RRDY IRQ while no data requested\n"); 905 break; 906 case 0x05: /* Transmit data ready */ 907 if (omap->buf_len) { 908 w = *omap->buf++; 909 omap->buf_len--; 910 if (omap->buf_len) { 911 w |= *omap->buf++ << 8; 912 omap->buf_len--; 913 } 914 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w); 915 } else 916 dev_err(omap->dev, "XRDY IRQ while no data to send\n"); 917 break; 918 default: 919 return IRQ_NONE; 920 } 921 922 return IRQ_HANDLED; 923 } 924 #else 925 #define omap_i2c_omap1_isr NULL 926 #endif 927 928 /* 929 * OMAP3430 Errata i462: When an XRDY/XDR is hit, wait for XUDF before writing 930 * data to DATA_REG. Otherwise some data bytes can be lost while transferring 931 * them from the memory to the I2C interface. 932 */ 933 static int errata_omap3_i462(struct omap_i2c_dev *omap) 934 { 935 unsigned long timeout = 10000; 936 u16 stat; 937 938 do { 939 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 940 if (stat & OMAP_I2C_STAT_XUDF) 941 break; 942 943 if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) { 944 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_XRDY | 945 OMAP_I2C_STAT_XDR)); 946 if (stat & OMAP_I2C_STAT_NACK) { 947 omap->cmd_err |= OMAP_I2C_STAT_NACK; 948 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK); 949 } 950 951 if (stat & OMAP_I2C_STAT_AL) { 952 dev_err(omap->dev, "Arbitration lost\n"); 953 omap->cmd_err |= OMAP_I2C_STAT_AL; 954 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL); 955 } 956 957 return -EIO; 958 } 959 960 cpu_relax(); 961 } while (--timeout); 962 963 if (!timeout) { 964 dev_err(omap->dev, "timeout waiting on XUDF bit\n"); 965 return 0; 966 } 967 968 return 0; 969 } 970 971 static void omap_i2c_receive_data(struct omap_i2c_dev *omap, u8 num_bytes, 972 bool is_rdr) 973 { 974 u16 w; 975 976 while (num_bytes--) { 977 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG); 978 *omap->buf++ = w; 979 omap->buf_len--; 980 981 /* 982 * Data reg in 2430, omap3 and 983 * omap4 is 8 bit wide 984 */ 985 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) { 986 *omap->buf++ = w >> 8; 987 omap->buf_len--; 988 } 989 } 990 } 991 992 static int omap_i2c_transmit_data(struct omap_i2c_dev *omap, u8 num_bytes, 993 bool is_xdr) 994 { 995 u16 w; 996 997 while (num_bytes--) { 998 w = *omap->buf++; 999 omap->buf_len--; 1000 1001 /* 1002 * Data reg in 2430, omap3 and 1003 * omap4 is 8 bit wide 1004 */ 1005 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) { 1006 w |= *omap->buf++ << 8; 1007 omap->buf_len--; 1008 } 1009 1010 if (omap->errata & I2C_OMAP_ERRATA_I462) { 1011 int ret; 1012 1013 ret = errata_omap3_i462(omap); 1014 if (ret < 0) 1015 return ret; 1016 } 1017 1018 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w); 1019 } 1020 1021 return 0; 1022 } 1023 1024 static irqreturn_t 1025 omap_i2c_isr(int irq, void *dev_id) 1026 { 1027 struct omap_i2c_dev *omap = dev_id; 1028 irqreturn_t ret = IRQ_HANDLED; 1029 u16 mask; 1030 u16 stat; 1031 1032 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1033 mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1034 1035 if (stat & mask) 1036 ret = IRQ_WAKE_THREAD; 1037 1038 return ret; 1039 } 1040 1041 static irqreturn_t 1042 omap_i2c_isr_thread(int this_irq, void *dev_id) 1043 { 1044 struct omap_i2c_dev *omap = dev_id; 1045 u16 bits; 1046 u16 stat; 1047 int err = 0, count = 0; 1048 1049 do { 1050 bits = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1051 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1052 stat &= bits; 1053 1054 /* If we're in receiver mode, ignore XDR/XRDY */ 1055 if (omap->receiver) 1056 stat &= ~(OMAP_I2C_STAT_XDR | OMAP_I2C_STAT_XRDY); 1057 else 1058 stat &= ~(OMAP_I2C_STAT_RDR | OMAP_I2C_STAT_RRDY); 1059 1060 if (!stat) { 1061 /* my work here is done */ 1062 goto out; 1063 } 1064 1065 dev_dbg(omap->dev, "IRQ (ISR = 0x%04x)\n", stat); 1066 if (count++ == 100) { 1067 dev_warn(omap->dev, "Too much work in one IRQ\n"); 1068 break; 1069 } 1070 1071 if (stat & OMAP_I2C_STAT_NACK) { 1072 err |= OMAP_I2C_STAT_NACK; 1073 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK); 1074 } 1075 1076 if (stat & OMAP_I2C_STAT_AL) { 1077 dev_err(omap->dev, "Arbitration lost\n"); 1078 err |= OMAP_I2C_STAT_AL; 1079 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL); 1080 } 1081 1082 /* 1083 * ProDB0017052: Clear ARDY bit twice 1084 */ 1085 if (stat & OMAP_I2C_STAT_ARDY) 1086 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ARDY); 1087 1088 if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | 1089 OMAP_I2C_STAT_AL)) { 1090 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_RRDY | 1091 OMAP_I2C_STAT_RDR | 1092 OMAP_I2C_STAT_XRDY | 1093 OMAP_I2C_STAT_XDR | 1094 OMAP_I2C_STAT_ARDY)); 1095 break; 1096 } 1097 1098 if (stat & OMAP_I2C_STAT_RDR) { 1099 u8 num_bytes = 1; 1100 1101 if (omap->fifo_size) 1102 num_bytes = omap->buf_len; 1103 1104 if (omap->errata & I2C_OMAP_ERRATA_I207) { 1105 i2c_omap_errata_i207(omap, stat); 1106 num_bytes = (omap_i2c_read_reg(omap, 1107 OMAP_I2C_BUFSTAT_REG) >> 8) & 0x3F; 1108 } 1109 1110 omap_i2c_receive_data(omap, num_bytes, true); 1111 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR); 1112 continue; 1113 } 1114 1115 if (stat & OMAP_I2C_STAT_RRDY) { 1116 u8 num_bytes = 1; 1117 1118 if (omap->threshold) 1119 num_bytes = omap->threshold; 1120 1121 omap_i2c_receive_data(omap, num_bytes, false); 1122 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RRDY); 1123 continue; 1124 } 1125 1126 if (stat & OMAP_I2C_STAT_XDR) { 1127 u8 num_bytes = 1; 1128 int ret; 1129 1130 if (omap->fifo_size) 1131 num_bytes = omap->buf_len; 1132 1133 ret = omap_i2c_transmit_data(omap, num_bytes, true); 1134 if (ret < 0) 1135 break; 1136 1137 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XDR); 1138 continue; 1139 } 1140 1141 if (stat & OMAP_I2C_STAT_XRDY) { 1142 u8 num_bytes = 1; 1143 int ret; 1144 1145 if (omap->threshold) 1146 num_bytes = omap->threshold; 1147 1148 ret = omap_i2c_transmit_data(omap, num_bytes, false); 1149 if (ret < 0) 1150 break; 1151 1152 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XRDY); 1153 continue; 1154 } 1155 1156 if (stat & OMAP_I2C_STAT_ROVR) { 1157 dev_err(omap->dev, "Receive overrun\n"); 1158 err |= OMAP_I2C_STAT_ROVR; 1159 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ROVR); 1160 break; 1161 } 1162 1163 if (stat & OMAP_I2C_STAT_XUDF) { 1164 dev_err(omap->dev, "Transmit underflow\n"); 1165 err |= OMAP_I2C_STAT_XUDF; 1166 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XUDF); 1167 break; 1168 } 1169 } while (stat); 1170 1171 omap_i2c_complete_cmd(omap, err); 1172 1173 out: 1174 return IRQ_HANDLED; 1175 } 1176 1177 static const struct i2c_algorithm omap_i2c_algo = { 1178 .master_xfer = omap_i2c_xfer, 1179 .functionality = omap_i2c_func, 1180 }; 1181 1182 #ifdef CONFIG_OF 1183 static struct omap_i2c_bus_platform_data omap2420_pdata = { 1184 .rev = OMAP_I2C_IP_VERSION_1, 1185 .flags = OMAP_I2C_FLAG_NO_FIFO | 1186 OMAP_I2C_FLAG_SIMPLE_CLOCK | 1187 OMAP_I2C_FLAG_16BIT_DATA_REG | 1188 OMAP_I2C_FLAG_BUS_SHIFT_2, 1189 }; 1190 1191 static struct omap_i2c_bus_platform_data omap2430_pdata = { 1192 .rev = OMAP_I2C_IP_VERSION_1, 1193 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2 | 1194 OMAP_I2C_FLAG_FORCE_19200_INT_CLK, 1195 }; 1196 1197 static struct omap_i2c_bus_platform_data omap3_pdata = { 1198 .rev = OMAP_I2C_IP_VERSION_1, 1199 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2, 1200 }; 1201 1202 static struct omap_i2c_bus_platform_data omap4_pdata = { 1203 .rev = OMAP_I2C_IP_VERSION_2, 1204 }; 1205 1206 static const struct of_device_id omap_i2c_of_match[] = { 1207 { 1208 .compatible = "ti,omap4-i2c", 1209 .data = &omap4_pdata, 1210 }, 1211 { 1212 .compatible = "ti,omap3-i2c", 1213 .data = &omap3_pdata, 1214 }, 1215 { 1216 .compatible = "ti,omap2430-i2c", 1217 .data = &omap2430_pdata, 1218 }, 1219 { 1220 .compatible = "ti,omap2420-i2c", 1221 .data = &omap2420_pdata, 1222 }, 1223 { }, 1224 }; 1225 MODULE_DEVICE_TABLE(of, omap_i2c_of_match); 1226 #endif 1227 1228 #define OMAP_I2C_SCHEME(rev) ((rev & 0xc000) >> 14) 1229 1230 #define OMAP_I2C_REV_SCHEME_0_MAJOR(rev) (rev >> 4) 1231 #define OMAP_I2C_REV_SCHEME_0_MINOR(rev) (rev & 0xf) 1232 1233 #define OMAP_I2C_REV_SCHEME_1_MAJOR(rev) ((rev & 0x0700) >> 7) 1234 #define OMAP_I2C_REV_SCHEME_1_MINOR(rev) (rev & 0x1f) 1235 #define OMAP_I2C_SCHEME_0 0 1236 #define OMAP_I2C_SCHEME_1 1 1237 1238 static int omap_i2c_get_scl(struct i2c_adapter *adap) 1239 { 1240 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1241 u32 reg; 1242 1243 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1244 1245 return reg & OMAP_I2C_SYSTEST_SCL_I_FUNC; 1246 } 1247 1248 static int omap_i2c_get_sda(struct i2c_adapter *adap) 1249 { 1250 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1251 u32 reg; 1252 1253 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1254 1255 return reg & OMAP_I2C_SYSTEST_SDA_I_FUNC; 1256 } 1257 1258 static void omap_i2c_set_scl(struct i2c_adapter *adap, int val) 1259 { 1260 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1261 u32 reg; 1262 1263 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1264 if (val) 1265 reg |= OMAP_I2C_SYSTEST_SCL_O; 1266 else 1267 reg &= ~OMAP_I2C_SYSTEST_SCL_O; 1268 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1269 } 1270 1271 static void omap_i2c_prepare_recovery(struct i2c_adapter *adap) 1272 { 1273 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1274 u32 reg; 1275 1276 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1277 /* enable test mode */ 1278 reg |= OMAP_I2C_SYSTEST_ST_EN; 1279 /* select SDA/SCL IO mode */ 1280 reg |= 3 << OMAP_I2C_SYSTEST_TMODE_SHIFT; 1281 /* set SCL to high-impedance state (reset value is 0) */ 1282 reg |= OMAP_I2C_SYSTEST_SCL_O; 1283 /* set SDA to high-impedance state (reset value is 0) */ 1284 reg |= OMAP_I2C_SYSTEST_SDA_O; 1285 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1286 } 1287 1288 static void omap_i2c_unprepare_recovery(struct i2c_adapter *adap) 1289 { 1290 struct omap_i2c_dev *dev = i2c_get_adapdata(adap); 1291 u32 reg; 1292 1293 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG); 1294 /* restore reset values */ 1295 reg &= ~OMAP_I2C_SYSTEST_ST_EN; 1296 reg &= ~OMAP_I2C_SYSTEST_TMODE_MASK; 1297 reg &= ~OMAP_I2C_SYSTEST_SCL_O; 1298 reg &= ~OMAP_I2C_SYSTEST_SDA_O; 1299 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg); 1300 } 1301 1302 static struct i2c_bus_recovery_info omap_i2c_bus_recovery_info = { 1303 .get_scl = omap_i2c_get_scl, 1304 .get_sda = omap_i2c_get_sda, 1305 .set_scl = omap_i2c_set_scl, 1306 .prepare_recovery = omap_i2c_prepare_recovery, 1307 .unprepare_recovery = omap_i2c_unprepare_recovery, 1308 .recover_bus = i2c_generic_scl_recovery, 1309 }; 1310 1311 static int 1312 omap_i2c_probe(struct platform_device *pdev) 1313 { 1314 struct omap_i2c_dev *omap; 1315 struct i2c_adapter *adap; 1316 struct resource *mem; 1317 const struct omap_i2c_bus_platform_data *pdata = 1318 dev_get_platdata(&pdev->dev); 1319 struct device_node *node = pdev->dev.of_node; 1320 const struct of_device_id *match; 1321 int irq; 1322 int r; 1323 u32 rev; 1324 u16 minor, major; 1325 1326 irq = platform_get_irq(pdev, 0); 1327 if (irq < 0) { 1328 dev_err(&pdev->dev, "no irq resource?\n"); 1329 return irq; 1330 } 1331 1332 omap = devm_kzalloc(&pdev->dev, sizeof(struct omap_i2c_dev), GFP_KERNEL); 1333 if (!omap) 1334 return -ENOMEM; 1335 1336 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1337 omap->base = devm_ioremap_resource(&pdev->dev, mem); 1338 if (IS_ERR(omap->base)) 1339 return PTR_ERR(omap->base); 1340 1341 match = of_match_device(of_match_ptr(omap_i2c_of_match), &pdev->dev); 1342 if (match) { 1343 u32 freq = 100000; /* default to 100000 Hz */ 1344 1345 pdata = match->data; 1346 omap->flags = pdata->flags; 1347 1348 of_property_read_u32(node, "clock-frequency", &freq); 1349 /* convert DT freq value in Hz into kHz for speed */ 1350 omap->speed = freq / 1000; 1351 } else if (pdata != NULL) { 1352 omap->speed = pdata->clkrate; 1353 omap->flags = pdata->flags; 1354 omap->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat; 1355 } 1356 1357 omap->dev = &pdev->dev; 1358 omap->irq = irq; 1359 1360 platform_set_drvdata(pdev, omap); 1361 init_completion(&omap->cmd_complete); 1362 1363 omap->reg_shift = (omap->flags >> OMAP_I2C_FLAG_BUS_SHIFT__SHIFT) & 3; 1364 1365 pm_runtime_enable(omap->dev); 1366 pm_runtime_set_autosuspend_delay(omap->dev, OMAP_I2C_PM_TIMEOUT); 1367 pm_runtime_use_autosuspend(omap->dev); 1368 1369 r = pm_runtime_get_sync(omap->dev); 1370 if (r < 0) 1371 goto err_free_mem; 1372 1373 /* 1374 * Read the Rev hi bit-[15:14] ie scheme this is 1 indicates ver2. 1375 * On omap1/3/2 Offset 4 is IE Reg the bit [15:14] is 0 at reset. 1376 * Also since the omap_i2c_read_reg uses reg_map_ip_* a 1377 * readw_relaxed is done. 1378 */ 1379 rev = readw_relaxed(omap->base + 0x04); 1380 1381 omap->scheme = OMAP_I2C_SCHEME(rev); 1382 switch (omap->scheme) { 1383 case OMAP_I2C_SCHEME_0: 1384 omap->regs = (u8 *)reg_map_ip_v1; 1385 omap->rev = omap_i2c_read_reg(omap, OMAP_I2C_REV_REG); 1386 minor = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev); 1387 major = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev); 1388 break; 1389 case OMAP_I2C_SCHEME_1: 1390 /* FALLTHROUGH */ 1391 default: 1392 omap->regs = (u8 *)reg_map_ip_v2; 1393 rev = (rev << 16) | 1394 omap_i2c_read_reg(omap, OMAP_I2C_IP_V2_REVNB_LO); 1395 minor = OMAP_I2C_REV_SCHEME_1_MINOR(rev); 1396 major = OMAP_I2C_REV_SCHEME_1_MAJOR(rev); 1397 omap->rev = rev; 1398 } 1399 1400 omap->errata = 0; 1401 1402 if (omap->rev >= OMAP_I2C_REV_ON_2430 && 1403 omap->rev < OMAP_I2C_REV_ON_4430_PLUS) 1404 omap->errata |= I2C_OMAP_ERRATA_I207; 1405 1406 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530) 1407 omap->errata |= I2C_OMAP_ERRATA_I462; 1408 1409 if (!(omap->flags & OMAP_I2C_FLAG_NO_FIFO)) { 1410 u16 s; 1411 1412 /* Set up the fifo size - Get total size */ 1413 s = (omap_i2c_read_reg(omap, OMAP_I2C_BUFSTAT_REG) >> 14) & 0x3; 1414 omap->fifo_size = 0x8 << s; 1415 1416 /* 1417 * Set up notification threshold as half the total available 1418 * size. This is to ensure that we can handle the status on int 1419 * call back latencies. 1420 */ 1421 1422 omap->fifo_size = (omap->fifo_size / 2); 1423 1424 if (omap->rev < OMAP_I2C_REV_ON_3630) 1425 omap->b_hw = 1; /* Enable hardware fixes */ 1426 1427 /* calculate wakeup latency constraint for MPU */ 1428 if (omap->set_mpu_wkup_lat != NULL) 1429 omap->latency = (1000000 * omap->fifo_size) / 1430 (1000 * omap->speed / 8); 1431 } 1432 1433 /* reset ASAP, clearing any IRQs */ 1434 omap_i2c_init(omap); 1435 1436 if (omap->rev < OMAP_I2C_OMAP1_REV_2) 1437 r = devm_request_irq(&pdev->dev, omap->irq, omap_i2c_omap1_isr, 1438 IRQF_NO_SUSPEND, pdev->name, omap); 1439 else 1440 r = devm_request_threaded_irq(&pdev->dev, omap->irq, 1441 omap_i2c_isr, omap_i2c_isr_thread, 1442 IRQF_NO_SUSPEND | IRQF_ONESHOT, 1443 pdev->name, omap); 1444 1445 if (r) { 1446 dev_err(omap->dev, "failure requesting irq %i\n", omap->irq); 1447 goto err_unuse_clocks; 1448 } 1449 1450 adap = &omap->adapter; 1451 i2c_set_adapdata(adap, omap); 1452 adap->owner = THIS_MODULE; 1453 adap->class = I2C_CLASS_DEPRECATED; 1454 strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); 1455 adap->algo = &omap_i2c_algo; 1456 adap->dev.parent = &pdev->dev; 1457 adap->dev.of_node = pdev->dev.of_node; 1458 adap->bus_recovery_info = &omap_i2c_bus_recovery_info; 1459 1460 /* i2c device drivers may be active on return from add_adapter() */ 1461 adap->nr = pdev->id; 1462 r = i2c_add_numbered_adapter(adap); 1463 if (r) 1464 goto err_unuse_clocks; 1465 1466 dev_info(omap->dev, "bus %d rev%d.%d at %d kHz\n", adap->nr, 1467 major, minor, omap->speed); 1468 1469 pm_runtime_mark_last_busy(omap->dev); 1470 pm_runtime_put_autosuspend(omap->dev); 1471 1472 return 0; 1473 1474 err_unuse_clocks: 1475 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 1476 pm_runtime_dont_use_autosuspend(omap->dev); 1477 pm_runtime_put_sync(omap->dev); 1478 pm_runtime_disable(&pdev->dev); 1479 err_free_mem: 1480 1481 return r; 1482 } 1483 1484 static int omap_i2c_remove(struct platform_device *pdev) 1485 { 1486 struct omap_i2c_dev *omap = platform_get_drvdata(pdev); 1487 int ret; 1488 1489 i2c_del_adapter(&omap->adapter); 1490 ret = pm_runtime_get_sync(&pdev->dev); 1491 if (ret < 0) 1492 return ret; 1493 1494 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0); 1495 pm_runtime_dont_use_autosuspend(&pdev->dev); 1496 pm_runtime_put_sync(&pdev->dev); 1497 pm_runtime_disable(&pdev->dev); 1498 return 0; 1499 } 1500 1501 #ifdef CONFIG_PM 1502 static int omap_i2c_runtime_suspend(struct device *dev) 1503 { 1504 struct omap_i2c_dev *omap = dev_get_drvdata(dev); 1505 1506 omap->iestate = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG); 1507 1508 if (omap->scheme == OMAP_I2C_SCHEME_0) 1509 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, 0); 1510 else 1511 omap_i2c_write_reg(omap, OMAP_I2C_IP_V2_IRQENABLE_CLR, 1512 OMAP_I2C_IP_V2_INTERRUPTS_MASK); 1513 1514 if (omap->rev < OMAP_I2C_OMAP1_REV_2) { 1515 omap_i2c_read_reg(omap, OMAP_I2C_IV_REG); /* Read clears */ 1516 } else { 1517 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, omap->iestate); 1518 1519 /* Flush posted write */ 1520 omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG); 1521 } 1522 1523 pinctrl_pm_select_sleep_state(dev); 1524 1525 return 0; 1526 } 1527 1528 static int omap_i2c_runtime_resume(struct device *dev) 1529 { 1530 struct omap_i2c_dev *omap = dev_get_drvdata(dev); 1531 1532 pinctrl_pm_select_default_state(dev); 1533 1534 if (!omap->regs) 1535 return 0; 1536 1537 __omap_i2c_init(omap); 1538 1539 return 0; 1540 } 1541 1542 static const struct dev_pm_ops omap_i2c_pm_ops = { 1543 SET_RUNTIME_PM_OPS(omap_i2c_runtime_suspend, 1544 omap_i2c_runtime_resume, NULL) 1545 }; 1546 #define OMAP_I2C_PM_OPS (&omap_i2c_pm_ops) 1547 #else 1548 #define OMAP_I2C_PM_OPS NULL 1549 #endif /* CONFIG_PM */ 1550 1551 static struct platform_driver omap_i2c_driver = { 1552 .probe = omap_i2c_probe, 1553 .remove = omap_i2c_remove, 1554 .driver = { 1555 .name = "omap_i2c", 1556 .pm = OMAP_I2C_PM_OPS, 1557 .of_match_table = of_match_ptr(omap_i2c_of_match), 1558 }, 1559 }; 1560 1561 /* I2C may be needed to bring up other drivers */ 1562 static int __init 1563 omap_i2c_init_driver(void) 1564 { 1565 return platform_driver_register(&omap_i2c_driver); 1566 } 1567 subsys_initcall(omap_i2c_init_driver); 1568 1569 static void __exit omap_i2c_exit_driver(void) 1570 { 1571 platform_driver_unregister(&omap_i2c_driver); 1572 } 1573 module_exit(omap_i2c_exit_driver); 1574 1575 MODULE_AUTHOR("MontaVista Software, Inc. (and others)"); 1576 MODULE_DESCRIPTION("TI OMAP I2C bus adapter"); 1577 MODULE_LICENSE("GPL"); 1578 MODULE_ALIAS("platform:omap_i2c"); 1579