1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver 4 * 5 * Copyright (C) 2013 Samsung Electronics Co., Ltd. 6 */ 7 8 #include <linux/kernel.h> 9 #include <linux/module.h> 10 11 #include <linux/i2c.h> 12 #include <linux/time.h> 13 #include <linux/interrupt.h> 14 #include <linux/delay.h> 15 #include <linux/errno.h> 16 #include <linux/err.h> 17 #include <linux/platform_device.h> 18 #include <linux/clk.h> 19 #include <linux/slab.h> 20 #include <linux/io.h> 21 #include <linux/of.h> 22 #include <linux/spinlock.h> 23 24 /* 25 * HSI2C controller from Samsung supports 2 modes of operation 26 * 1. Auto mode: Where in master automatically controls the whole transaction 27 * 2. Manual mode: Software controls the transaction by issuing commands 28 * START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register. 29 * 30 * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register 31 * 32 * Special bits are available for both modes of operation to set commands 33 * and for checking transfer status 34 */ 35 36 /* Register Map */ 37 #define HSI2C_CTL 0x00 38 #define HSI2C_FIFO_CTL 0x04 39 #define HSI2C_TRAILIG_CTL 0x08 40 #define HSI2C_CLK_CTL 0x0C 41 #define HSI2C_CLK_SLOT 0x10 42 #define HSI2C_INT_ENABLE 0x20 43 #define HSI2C_INT_STATUS 0x24 44 #define HSI2C_ERR_STATUS 0x2C 45 #define HSI2C_FIFO_STATUS 0x30 46 #define HSI2C_TX_DATA 0x34 47 #define HSI2C_RX_DATA 0x38 48 #define HSI2C_CONF 0x40 49 #define HSI2C_AUTO_CONF 0x44 50 #define HSI2C_TIMEOUT 0x48 51 #define HSI2C_MANUAL_CMD 0x4C 52 #define HSI2C_TRANS_STATUS 0x50 53 #define HSI2C_TIMING_HS1 0x54 54 #define HSI2C_TIMING_HS2 0x58 55 #define HSI2C_TIMING_HS3 0x5C 56 #define HSI2C_TIMING_FS1 0x60 57 #define HSI2C_TIMING_FS2 0x64 58 #define HSI2C_TIMING_FS3 0x68 59 #define HSI2C_TIMING_SLA 0x6C 60 #define HSI2C_ADDR 0x70 61 62 /* I2C_CTL Register bits */ 63 #define HSI2C_FUNC_MODE_I2C (1u << 0) 64 #define HSI2C_MASTER (1u << 3) 65 #define HSI2C_RXCHON (1u << 6) 66 #define HSI2C_TXCHON (1u << 7) 67 #define HSI2C_SW_RST (1u << 31) 68 69 /* I2C_FIFO_CTL Register bits */ 70 #define HSI2C_RXFIFO_EN (1u << 0) 71 #define HSI2C_TXFIFO_EN (1u << 1) 72 #define HSI2C_RXFIFO_TRIGGER_LEVEL(x) ((x) << 4) 73 #define HSI2C_TXFIFO_TRIGGER_LEVEL(x) ((x) << 16) 74 75 /* I2C_TRAILING_CTL Register bits */ 76 #define HSI2C_TRAILING_COUNT (0xf) 77 78 /* I2C_INT_EN Register bits */ 79 #define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0) 80 #define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1) 81 #define HSI2C_INT_TRAILING_EN (1u << 6) 82 83 /* I2C_INT_STAT Register bits */ 84 #define HSI2C_INT_TX_ALMOSTEMPTY (1u << 0) 85 #define HSI2C_INT_RX_ALMOSTFULL (1u << 1) 86 #define HSI2C_INT_TX_UNDERRUN (1u << 2) 87 #define HSI2C_INT_TX_OVERRUN (1u << 3) 88 #define HSI2C_INT_RX_UNDERRUN (1u << 4) 89 #define HSI2C_INT_RX_OVERRUN (1u << 5) 90 #define HSI2C_INT_TRAILING (1u << 6) 91 #define HSI2C_INT_I2C (1u << 9) 92 93 #define HSI2C_INT_TRANS_DONE (1u << 7) 94 #define HSI2C_INT_TRANS_ABORT (1u << 8) 95 #define HSI2C_INT_NO_DEV_ACK (1u << 9) 96 #define HSI2C_INT_NO_DEV (1u << 10) 97 #define HSI2C_INT_TIMEOUT (1u << 11) 98 #define HSI2C_INT_I2C_TRANS (HSI2C_INT_TRANS_DONE | \ 99 HSI2C_INT_TRANS_ABORT | \ 100 HSI2C_INT_NO_DEV_ACK | \ 101 HSI2C_INT_NO_DEV | \ 102 HSI2C_INT_TIMEOUT) 103 104 /* I2C_FIFO_STAT Register bits */ 105 #define HSI2C_RX_FIFO_EMPTY (1u << 24) 106 #define HSI2C_RX_FIFO_FULL (1u << 23) 107 #define HSI2C_RX_FIFO_LVL(x) ((x >> 16) & 0x7f) 108 #define HSI2C_TX_FIFO_EMPTY (1u << 8) 109 #define HSI2C_TX_FIFO_FULL (1u << 7) 110 #define HSI2C_TX_FIFO_LVL(x) ((x >> 0) & 0x7f) 111 112 /* I2C_CONF Register bits */ 113 #define HSI2C_AUTO_MODE (1u << 31) 114 #define HSI2C_10BIT_ADDR_MODE (1u << 30) 115 #define HSI2C_HS_MODE (1u << 29) 116 117 /* I2C_AUTO_CONF Register bits */ 118 #define HSI2C_READ_WRITE (1u << 16) 119 #define HSI2C_STOP_AFTER_TRANS (1u << 17) 120 #define HSI2C_MASTER_RUN (1u << 31) 121 122 /* I2C_TIMEOUT Register bits */ 123 #define HSI2C_TIMEOUT_EN (1u << 31) 124 #define HSI2C_TIMEOUT_MASK 0xff 125 126 /* I2C_MANUAL_CMD register bits */ 127 #define HSI2C_CMD_READ_DATA (1u << 4) 128 #define HSI2C_CMD_SEND_STOP (1u << 2) 129 130 /* I2C_TRANS_STATUS register bits */ 131 #define HSI2C_MASTER_BUSY (1u << 17) 132 #define HSI2C_SLAVE_BUSY (1u << 16) 133 134 /* I2C_TRANS_STATUS register bits for Exynos5 variant */ 135 #define HSI2C_TIMEOUT_AUTO (1u << 4) 136 #define HSI2C_NO_DEV (1u << 3) 137 #define HSI2C_NO_DEV_ACK (1u << 2) 138 #define HSI2C_TRANS_ABORT (1u << 1) 139 #define HSI2C_TRANS_DONE (1u << 0) 140 141 /* I2C_TRANS_STATUS register bits for Exynos7 variant */ 142 #define HSI2C_MASTER_ST_MASK 0xf 143 #define HSI2C_MASTER_ST_IDLE 0x0 144 #define HSI2C_MASTER_ST_START 0x1 145 #define HSI2C_MASTER_ST_RESTART 0x2 146 #define HSI2C_MASTER_ST_STOP 0x3 147 #define HSI2C_MASTER_ST_MASTER_ID 0x4 148 #define HSI2C_MASTER_ST_ADDR0 0x5 149 #define HSI2C_MASTER_ST_ADDR1 0x6 150 #define HSI2C_MASTER_ST_ADDR2 0x7 151 #define HSI2C_MASTER_ST_ADDR_SR 0x8 152 #define HSI2C_MASTER_ST_READ 0x9 153 #define HSI2C_MASTER_ST_WRITE 0xa 154 #define HSI2C_MASTER_ST_NO_ACK 0xb 155 #define HSI2C_MASTER_ST_LOSE 0xc 156 #define HSI2C_MASTER_ST_WAIT 0xd 157 #define HSI2C_MASTER_ST_WAIT_CMD 0xe 158 159 /* I2C_ADDR register bits */ 160 #define HSI2C_SLV_ADDR_SLV(x) ((x & 0x3ff) << 0) 161 #define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10) 162 #define HSI2C_MASTER_ID(x) ((x & 0xff) << 24) 163 #define MASTER_ID(x) ((x & 0x7) + 0x08) 164 165 #define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(100)) 166 167 enum i2c_type_exynos { 168 I2C_TYPE_EXYNOS5, 169 I2C_TYPE_EXYNOS7, 170 I2C_TYPE_EXYNOSAUTOV9, 171 }; 172 173 struct exynos5_i2c { 174 struct i2c_adapter adap; 175 176 struct i2c_msg *msg; 177 struct completion msg_complete; 178 unsigned int msg_ptr; 179 180 unsigned int irq; 181 182 void __iomem *regs; 183 struct clk *clk; /* operating clock */ 184 struct clk *pclk; /* bus clock */ 185 struct device *dev; 186 int state; 187 188 spinlock_t lock; /* IRQ synchronization */ 189 190 /* 191 * Since the TRANS_DONE bit is cleared on read, and we may read it 192 * either during an IRQ or after a transaction, keep track of its 193 * state here. 194 */ 195 int trans_done; 196 197 /* Controller operating frequency */ 198 unsigned int op_clock; 199 200 /* Version of HS-I2C Hardware */ 201 const struct exynos_hsi2c_variant *variant; 202 }; 203 204 /** 205 * struct exynos_hsi2c_variant - platform specific HSI2C driver data 206 * @fifo_depth: the fifo depth supported by the HSI2C module 207 * @hw: the hardware variant of Exynos I2C controller 208 * 209 * Specifies platform specific configuration of HSI2C module. 210 * Note: A structure for driver specific platform data is used for future 211 * expansion of its usage. 212 */ 213 struct exynos_hsi2c_variant { 214 unsigned int fifo_depth; 215 enum i2c_type_exynos hw; 216 }; 217 218 static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = { 219 .fifo_depth = 64, 220 .hw = I2C_TYPE_EXYNOS5, 221 }; 222 223 static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = { 224 .fifo_depth = 16, 225 .hw = I2C_TYPE_EXYNOS5, 226 }; 227 228 static const struct exynos_hsi2c_variant exynos7_hsi2c_data = { 229 .fifo_depth = 16, 230 .hw = I2C_TYPE_EXYNOS7, 231 }; 232 233 static const struct exynos_hsi2c_variant exynosautov9_hsi2c_data = { 234 .fifo_depth = 64, 235 .hw = I2C_TYPE_EXYNOSAUTOV9, 236 }; 237 238 static const struct of_device_id exynos5_i2c_match[] = { 239 { 240 .compatible = "samsung,exynos5-hsi2c", 241 .data = &exynos5250_hsi2c_data 242 }, { 243 .compatible = "samsung,exynos5250-hsi2c", 244 .data = &exynos5250_hsi2c_data 245 }, { 246 .compatible = "samsung,exynos5260-hsi2c", 247 .data = &exynos5260_hsi2c_data 248 }, { 249 .compatible = "samsung,exynos7-hsi2c", 250 .data = &exynos7_hsi2c_data 251 }, { 252 .compatible = "samsung,exynosautov9-hsi2c", 253 .data = &exynosautov9_hsi2c_data 254 }, {}, 255 }; 256 MODULE_DEVICE_TABLE(of, exynos5_i2c_match); 257 258 static void exynos5_i2c_clr_pend_irq(struct exynos5_i2c *i2c) 259 { 260 writel(readl(i2c->regs + HSI2C_INT_STATUS), 261 i2c->regs + HSI2C_INT_STATUS); 262 } 263 264 /* 265 * exynos5_i2c_set_timing: updates the registers with appropriate 266 * timing values calculated 267 * 268 * Timing values for operation are calculated against either 100kHz 269 * or 1MHz controller operating frequency. 270 * 271 * Returns 0 on success, -EINVAL if the cycle length cannot 272 * be calculated. 273 */ 274 static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, bool hs_timings) 275 { 276 u32 i2c_timing_s1; 277 u32 i2c_timing_s2; 278 u32 i2c_timing_s3; 279 u32 i2c_timing_sla; 280 unsigned int t_start_su, t_start_hd; 281 unsigned int t_stop_su; 282 unsigned int t_data_su, t_data_hd; 283 unsigned int t_scl_l, t_scl_h; 284 unsigned int t_sr_release; 285 unsigned int t_ftl_cycle; 286 unsigned int clkin = clk_get_rate(i2c->clk); 287 unsigned int op_clk = hs_timings ? i2c->op_clock : 288 (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ) ? I2C_MAX_STANDARD_MODE_FREQ : 289 i2c->op_clock; 290 int div, clk_cycle, temp; 291 292 /* 293 * In case of HSI2C controllers in ExynosAutoV9: 294 * 295 * FSCL = IPCLK / ((CLK_DIV + 1) * 16) 296 * T_SCL_LOW = IPCLK * (CLK_DIV + 1) * (N + M) 297 * [N : number of 0's in the TSCL_H_HS] 298 * [M : number of 0's in the TSCL_L_HS] 299 * T_SCL_HIGH = IPCLK * (CLK_DIV + 1) * (N + M) 300 * [N : number of 1's in the TSCL_H_HS] 301 * [M : number of 1's in the TSCL_L_HS] 302 * 303 * Result of (N + M) is always 8. 304 * In general case, we don't need to control timing_s1 and timing_s2. 305 */ 306 if (i2c->variant->hw == I2C_TYPE_EXYNOSAUTOV9) { 307 div = ((clkin / (16 * i2c->op_clock)) - 1); 308 i2c_timing_s3 = div << 16; 309 if (hs_timings) 310 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3); 311 else 312 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3); 313 314 return 0; 315 } 316 317 /* 318 * In case of HSI2C controller in Exynos5 series 319 * FPCLK / FI2C = 320 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE 321 * 322 * In case of HSI2C controllers in Exynos7 series 323 * FPCLK / FI2C = 324 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + FLT_CYCLE 325 * 326 * clk_cycle := TSCLK_L + TSCLK_H 327 * temp := (CLK_DIV + 1) * (clk_cycle + 2) 328 * 329 * Constraints: 4 <= temp, 0 <= CLK_DIV < 256, 2 <= clk_cycle <= 510 330 * 331 */ 332 t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7; 333 temp = clkin / op_clk - 8 - t_ftl_cycle; 334 if (i2c->variant->hw != I2C_TYPE_EXYNOS7) 335 temp -= t_ftl_cycle; 336 div = temp / 512; 337 clk_cycle = temp / (div + 1) - 2; 338 if (temp < 4 || div >= 256 || clk_cycle < 2) { 339 dev_err(i2c->dev, "%s clock set-up failed\n", 340 hs_timings ? "HS" : "FS"); 341 return -EINVAL; 342 } 343 344 t_scl_l = clk_cycle / 2; 345 t_scl_h = clk_cycle / 2; 346 t_start_su = t_scl_l; 347 t_start_hd = t_scl_l; 348 t_stop_su = t_scl_l; 349 t_data_su = t_scl_l / 2; 350 t_data_hd = t_scl_l / 2; 351 t_sr_release = clk_cycle; 352 353 i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8; 354 i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0; 355 i2c_timing_s3 = div << 16 | t_sr_release << 0; 356 i2c_timing_sla = t_data_hd << 0; 357 358 dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n", 359 t_start_su, t_start_hd, t_stop_su); 360 dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n", 361 t_data_su, t_scl_l, t_scl_h); 362 dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n", 363 div, t_sr_release); 364 dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd); 365 366 if (hs_timings) { 367 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1); 368 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2); 369 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3); 370 } else { 371 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1); 372 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2); 373 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3); 374 } 375 writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA); 376 377 return 0; 378 } 379 380 static int exynos5_hsi2c_clock_setup(struct exynos5_i2c *i2c) 381 { 382 /* always set Fast Speed timings */ 383 int ret = exynos5_i2c_set_timing(i2c, false); 384 385 if (ret < 0 || i2c->op_clock < I2C_MAX_FAST_MODE_PLUS_FREQ) 386 return ret; 387 388 return exynos5_i2c_set_timing(i2c, true); 389 } 390 391 /* 392 * exynos5_i2c_init: configures the controller for I2C functionality 393 * Programs I2C controller for Master mode operation 394 */ 395 static void exynos5_i2c_init(struct exynos5_i2c *i2c) 396 { 397 u32 i2c_conf = readl(i2c->regs + HSI2C_CONF); 398 u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT); 399 400 /* Clear to disable Timeout */ 401 i2c_timeout &= ~HSI2C_TIMEOUT_EN; 402 writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT); 403 404 writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER), 405 i2c->regs + HSI2C_CTL); 406 writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL); 407 408 if (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ) { 409 writel(HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)), 410 i2c->regs + HSI2C_ADDR); 411 i2c_conf |= HSI2C_HS_MODE; 412 } 413 414 writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF); 415 } 416 417 static void exynos5_i2c_reset(struct exynos5_i2c *i2c) 418 { 419 u32 i2c_ctl; 420 421 /* Set and clear the bit for reset */ 422 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 423 i2c_ctl |= HSI2C_SW_RST; 424 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 425 426 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 427 i2c_ctl &= ~HSI2C_SW_RST; 428 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 429 430 /* We don't expect calculations to fail during the run */ 431 exynos5_hsi2c_clock_setup(i2c); 432 /* Initialize the configure registers */ 433 exynos5_i2c_init(i2c); 434 } 435 436 /* 437 * exynos5_i2c_irq: top level IRQ servicing routine 438 * 439 * INT_STATUS registers gives the interrupt details. Further, 440 * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed 441 * state of the bus. 442 */ 443 static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id) 444 { 445 struct exynos5_i2c *i2c = dev_id; 446 u32 fifo_level, int_status, fifo_status, trans_status; 447 unsigned char byte; 448 int len = 0; 449 450 i2c->state = -EINVAL; 451 452 spin_lock(&i2c->lock); 453 454 int_status = readl(i2c->regs + HSI2C_INT_STATUS); 455 writel(int_status, i2c->regs + HSI2C_INT_STATUS); 456 457 /* handle interrupt related to the transfer status */ 458 switch (i2c->variant->hw) { 459 case I2C_TYPE_EXYNOSAUTOV9: 460 fallthrough; 461 case I2C_TYPE_EXYNOS7: 462 if (int_status & HSI2C_INT_TRANS_DONE) { 463 i2c->trans_done = 1; 464 i2c->state = 0; 465 } else if (int_status & HSI2C_INT_TRANS_ABORT) { 466 dev_dbg(i2c->dev, "Deal with arbitration lose\n"); 467 i2c->state = -EAGAIN; 468 goto stop; 469 } else if (int_status & HSI2C_INT_NO_DEV_ACK) { 470 dev_dbg(i2c->dev, "No ACK from device\n"); 471 i2c->state = -ENXIO; 472 goto stop; 473 } else if (int_status & HSI2C_INT_NO_DEV) { 474 dev_dbg(i2c->dev, "No device\n"); 475 i2c->state = -ENXIO; 476 goto stop; 477 } else if (int_status & HSI2C_INT_TIMEOUT) { 478 dev_dbg(i2c->dev, "Accessing device timed out\n"); 479 i2c->state = -ETIMEDOUT; 480 goto stop; 481 } 482 483 break; 484 case I2C_TYPE_EXYNOS5: 485 if (!(int_status & HSI2C_INT_I2C)) 486 break; 487 488 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 489 if (trans_status & HSI2C_NO_DEV_ACK) { 490 dev_dbg(i2c->dev, "No ACK from device\n"); 491 i2c->state = -ENXIO; 492 goto stop; 493 } else if (trans_status & HSI2C_NO_DEV) { 494 dev_dbg(i2c->dev, "No device\n"); 495 i2c->state = -ENXIO; 496 goto stop; 497 } else if (trans_status & HSI2C_TRANS_ABORT) { 498 dev_dbg(i2c->dev, "Deal with arbitration lose\n"); 499 i2c->state = -EAGAIN; 500 goto stop; 501 } else if (trans_status & HSI2C_TIMEOUT_AUTO) { 502 dev_dbg(i2c->dev, "Accessing device timed out\n"); 503 i2c->state = -ETIMEDOUT; 504 goto stop; 505 } else if (trans_status & HSI2C_TRANS_DONE) { 506 i2c->trans_done = 1; 507 i2c->state = 0; 508 } 509 510 break; 511 } 512 513 if ((i2c->msg->flags & I2C_M_RD) && (int_status & 514 (HSI2C_INT_TRAILING | HSI2C_INT_RX_ALMOSTFULL))) { 515 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 516 fifo_level = HSI2C_RX_FIFO_LVL(fifo_status); 517 len = min(fifo_level, i2c->msg->len - i2c->msg_ptr); 518 519 while (len > 0) { 520 byte = (unsigned char) 521 readl(i2c->regs + HSI2C_RX_DATA); 522 i2c->msg->buf[i2c->msg_ptr++] = byte; 523 len--; 524 } 525 i2c->state = 0; 526 } else if (int_status & HSI2C_INT_TX_ALMOSTEMPTY) { 527 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 528 fifo_level = HSI2C_TX_FIFO_LVL(fifo_status); 529 530 len = i2c->variant->fifo_depth - fifo_level; 531 if (len > (i2c->msg->len - i2c->msg_ptr)) { 532 u32 int_en = readl(i2c->regs + HSI2C_INT_ENABLE); 533 534 int_en &= ~HSI2C_INT_TX_ALMOSTEMPTY_EN; 535 writel(int_en, i2c->regs + HSI2C_INT_ENABLE); 536 len = i2c->msg->len - i2c->msg_ptr; 537 } 538 539 while (len > 0) { 540 byte = i2c->msg->buf[i2c->msg_ptr++]; 541 writel(byte, i2c->regs + HSI2C_TX_DATA); 542 len--; 543 } 544 i2c->state = 0; 545 } 546 547 stop: 548 if ((i2c->trans_done && (i2c->msg->len == i2c->msg_ptr)) || 549 (i2c->state < 0)) { 550 writel(0, i2c->regs + HSI2C_INT_ENABLE); 551 exynos5_i2c_clr_pend_irq(i2c); 552 complete(&i2c->msg_complete); 553 } 554 555 spin_unlock(&i2c->lock); 556 557 return IRQ_HANDLED; 558 } 559 560 /* 561 * exynos5_i2c_wait_bus_idle 562 * 563 * Wait for the bus to go idle, indicated by the MASTER_BUSY bit being 564 * cleared. 565 * 566 * Returns -EBUSY if the bus cannot be bought to idle 567 */ 568 static int exynos5_i2c_wait_bus_idle(struct exynos5_i2c *i2c) 569 { 570 unsigned long stop_time; 571 u32 trans_status; 572 573 /* wait for 100 milli seconds for the bus to be idle */ 574 stop_time = jiffies + msecs_to_jiffies(100) + 1; 575 do { 576 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 577 if (!(trans_status & HSI2C_MASTER_BUSY)) 578 return 0; 579 580 usleep_range(50, 200); 581 } while (time_before(jiffies, stop_time)); 582 583 return -EBUSY; 584 } 585 586 static void exynos5_i2c_bus_recover(struct exynos5_i2c *i2c) 587 { 588 u32 val; 589 590 val = readl(i2c->regs + HSI2C_CTL) | HSI2C_RXCHON; 591 writel(val, i2c->regs + HSI2C_CTL); 592 val = readl(i2c->regs + HSI2C_CONF) & ~HSI2C_AUTO_MODE; 593 writel(val, i2c->regs + HSI2C_CONF); 594 595 /* 596 * Specification says master should send nine clock pulses. It can be 597 * emulated by sending manual read command (nine pulses for read eight 598 * bits + one pulse for NACK). 599 */ 600 writel(HSI2C_CMD_READ_DATA, i2c->regs + HSI2C_MANUAL_CMD); 601 exynos5_i2c_wait_bus_idle(i2c); 602 writel(HSI2C_CMD_SEND_STOP, i2c->regs + HSI2C_MANUAL_CMD); 603 exynos5_i2c_wait_bus_idle(i2c); 604 605 val = readl(i2c->regs + HSI2C_CTL) & ~HSI2C_RXCHON; 606 writel(val, i2c->regs + HSI2C_CTL); 607 val = readl(i2c->regs + HSI2C_CONF) | HSI2C_AUTO_MODE; 608 writel(val, i2c->regs + HSI2C_CONF); 609 } 610 611 static void exynos5_i2c_bus_check(struct exynos5_i2c *i2c) 612 { 613 unsigned long timeout; 614 615 if (i2c->variant->hw == I2C_TYPE_EXYNOS5) 616 return; 617 618 /* 619 * HSI2C_MASTER_ST_LOSE state (in Exynos7 and ExynosAutoV9 variants) 620 * before transaction indicates that bus is stuck (SDA is low). 621 * In such case bus recovery can be performed. 622 */ 623 timeout = jiffies + msecs_to_jiffies(100); 624 for (;;) { 625 u32 st = readl(i2c->regs + HSI2C_TRANS_STATUS); 626 627 if ((st & HSI2C_MASTER_ST_MASK) != HSI2C_MASTER_ST_LOSE) 628 return; 629 630 if (time_is_before_jiffies(timeout)) 631 return; 632 633 exynos5_i2c_bus_recover(i2c); 634 } 635 } 636 637 /* 638 * exynos5_i2c_message_start: Configures the bus and starts the xfer 639 * i2c: struct exynos5_i2c pointer for the current bus 640 * stop: Enables stop after transfer if set. Set for last transfer of 641 * in the list of messages. 642 * 643 * Configures the bus for read/write function 644 * Sets chip address to talk to, message length to be sent. 645 * Enables appropriate interrupts and sends start xfer command. 646 */ 647 static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop) 648 { 649 u32 i2c_ctl; 650 u32 int_en = 0; 651 u32 i2c_auto_conf = 0; 652 u32 i2c_addr = 0; 653 u32 fifo_ctl; 654 unsigned long flags; 655 unsigned short trig_lvl; 656 657 if (i2c->variant->hw == I2C_TYPE_EXYNOS5) 658 int_en |= HSI2C_INT_I2C; 659 else 660 int_en |= HSI2C_INT_I2C_TRANS; 661 662 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 663 i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON); 664 fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN; 665 666 if (i2c->msg->flags & I2C_M_RD) { 667 i2c_ctl |= HSI2C_RXCHON; 668 669 i2c_auto_conf |= HSI2C_READ_WRITE; 670 671 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 672 (i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len; 673 fifo_ctl |= HSI2C_RXFIFO_TRIGGER_LEVEL(trig_lvl); 674 675 int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN | 676 HSI2C_INT_TRAILING_EN); 677 } else { 678 i2c_ctl |= HSI2C_TXCHON; 679 680 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 681 (i2c->variant->fifo_depth * 1 / 4) : i2c->msg->len; 682 fifo_ctl |= HSI2C_TXFIFO_TRIGGER_LEVEL(trig_lvl); 683 684 int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN; 685 } 686 687 i2c_addr = HSI2C_SLV_ADDR_MAS(i2c->msg->addr); 688 689 if (i2c->op_clock >= I2C_MAX_FAST_MODE_PLUS_FREQ) 690 i2c_addr |= HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)); 691 692 writel(i2c_addr, i2c->regs + HSI2C_ADDR); 693 694 writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL); 695 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 696 697 exynos5_i2c_bus_check(i2c); 698 699 /* 700 * Enable interrupts before starting the transfer so that we don't 701 * miss any INT_I2C interrupts. 702 */ 703 spin_lock_irqsave(&i2c->lock, flags); 704 writel(int_en, i2c->regs + HSI2C_INT_ENABLE); 705 706 if (stop == 1) 707 i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS; 708 i2c_auto_conf |= i2c->msg->len; 709 i2c_auto_conf |= HSI2C_MASTER_RUN; 710 writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF); 711 spin_unlock_irqrestore(&i2c->lock, flags); 712 } 713 714 static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c, 715 struct i2c_msg *msgs, int stop) 716 { 717 unsigned long timeout; 718 int ret; 719 720 i2c->msg = msgs; 721 i2c->msg_ptr = 0; 722 i2c->trans_done = 0; 723 724 reinit_completion(&i2c->msg_complete); 725 726 exynos5_i2c_message_start(i2c, stop); 727 728 timeout = wait_for_completion_timeout(&i2c->msg_complete, 729 EXYNOS5_I2C_TIMEOUT); 730 if (timeout == 0) 731 ret = -ETIMEDOUT; 732 else 733 ret = i2c->state; 734 735 /* 736 * If this is the last message to be transfered (stop == 1) 737 * Then check if the bus can be brought back to idle. 738 */ 739 if (ret == 0 && stop) 740 ret = exynos5_i2c_wait_bus_idle(i2c); 741 742 if (ret < 0) { 743 exynos5_i2c_reset(i2c); 744 if (ret == -ETIMEDOUT) 745 dev_warn(i2c->dev, "%s timeout\n", 746 (msgs->flags & I2C_M_RD) ? "rx" : "tx"); 747 } 748 749 /* Return the state as in interrupt routine */ 750 return ret; 751 } 752 753 static int exynos5_i2c_xfer(struct i2c_adapter *adap, 754 struct i2c_msg *msgs, int num) 755 { 756 struct exynos5_i2c *i2c = adap->algo_data; 757 int i, ret; 758 759 ret = clk_enable(i2c->pclk); 760 if (ret) 761 return ret; 762 763 ret = clk_enable(i2c->clk); 764 if (ret) 765 goto err_pclk; 766 767 for (i = 0; i < num; ++i) { 768 ret = exynos5_i2c_xfer_msg(i2c, msgs + i, i + 1 == num); 769 if (ret) 770 break; 771 } 772 773 clk_disable(i2c->clk); 774 err_pclk: 775 clk_disable(i2c->pclk); 776 777 return ret ?: num; 778 } 779 780 static u32 exynos5_i2c_func(struct i2c_adapter *adap) 781 { 782 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); 783 } 784 785 static const struct i2c_algorithm exynos5_i2c_algorithm = { 786 .master_xfer = exynos5_i2c_xfer, 787 .functionality = exynos5_i2c_func, 788 }; 789 790 static int exynos5_i2c_probe(struct platform_device *pdev) 791 { 792 struct device_node *np = pdev->dev.of_node; 793 struct exynos5_i2c *i2c; 794 int ret; 795 796 i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL); 797 if (!i2c) 798 return -ENOMEM; 799 800 if (of_property_read_u32(np, "clock-frequency", &i2c->op_clock)) 801 i2c->op_clock = I2C_MAX_STANDARD_MODE_FREQ; 802 803 strscpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name)); 804 i2c->adap.owner = THIS_MODULE; 805 i2c->adap.algo = &exynos5_i2c_algorithm; 806 i2c->adap.retries = 3; 807 808 i2c->dev = &pdev->dev; 809 i2c->clk = devm_clk_get(&pdev->dev, "hsi2c"); 810 if (IS_ERR(i2c->clk)) { 811 dev_err(&pdev->dev, "cannot get clock\n"); 812 return -ENOENT; 813 } 814 815 i2c->pclk = devm_clk_get_optional(&pdev->dev, "hsi2c_pclk"); 816 if (IS_ERR(i2c->pclk)) { 817 return dev_err_probe(&pdev->dev, PTR_ERR(i2c->pclk), 818 "cannot get pclk"); 819 } 820 821 ret = clk_prepare_enable(i2c->pclk); 822 if (ret) 823 return ret; 824 825 ret = clk_prepare_enable(i2c->clk); 826 if (ret) 827 goto err_pclk; 828 829 i2c->regs = devm_platform_ioremap_resource(pdev, 0); 830 if (IS_ERR(i2c->regs)) { 831 ret = PTR_ERR(i2c->regs); 832 goto err_clk; 833 } 834 835 i2c->adap.dev.of_node = np; 836 i2c->adap.algo_data = i2c; 837 i2c->adap.dev.parent = &pdev->dev; 838 839 /* Clear pending interrupts from u-boot or misc causes */ 840 exynos5_i2c_clr_pend_irq(i2c); 841 842 spin_lock_init(&i2c->lock); 843 init_completion(&i2c->msg_complete); 844 845 i2c->irq = ret = platform_get_irq(pdev, 0); 846 if (ret < 0) 847 goto err_clk; 848 849 ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq, 850 IRQF_NO_SUSPEND, dev_name(&pdev->dev), i2c); 851 if (ret != 0) { 852 dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq); 853 goto err_clk; 854 } 855 856 i2c->variant = of_device_get_match_data(&pdev->dev); 857 858 ret = exynos5_hsi2c_clock_setup(i2c); 859 if (ret) 860 goto err_clk; 861 862 exynos5_i2c_reset(i2c); 863 864 ret = i2c_add_adapter(&i2c->adap); 865 if (ret < 0) 866 goto err_clk; 867 868 platform_set_drvdata(pdev, i2c); 869 870 clk_disable(i2c->clk); 871 clk_disable(i2c->pclk); 872 873 return 0; 874 875 err_clk: 876 clk_disable_unprepare(i2c->clk); 877 878 err_pclk: 879 clk_disable_unprepare(i2c->pclk); 880 return ret; 881 } 882 883 static void exynos5_i2c_remove(struct platform_device *pdev) 884 { 885 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 886 887 i2c_del_adapter(&i2c->adap); 888 889 clk_unprepare(i2c->clk); 890 clk_unprepare(i2c->pclk); 891 } 892 893 static int exynos5_i2c_suspend_noirq(struct device *dev) 894 { 895 struct exynos5_i2c *i2c = dev_get_drvdata(dev); 896 897 i2c_mark_adapter_suspended(&i2c->adap); 898 clk_unprepare(i2c->clk); 899 clk_unprepare(i2c->pclk); 900 901 return 0; 902 } 903 904 static int exynos5_i2c_resume_noirq(struct device *dev) 905 { 906 struct exynos5_i2c *i2c = dev_get_drvdata(dev); 907 int ret = 0; 908 909 ret = clk_prepare_enable(i2c->pclk); 910 if (ret) 911 return ret; 912 913 ret = clk_prepare_enable(i2c->clk); 914 if (ret) 915 goto err_pclk; 916 917 ret = exynos5_hsi2c_clock_setup(i2c); 918 if (ret) 919 goto err_clk; 920 921 exynos5_i2c_init(i2c); 922 clk_disable(i2c->clk); 923 clk_disable(i2c->pclk); 924 i2c_mark_adapter_resumed(&i2c->adap); 925 926 return 0; 927 928 err_clk: 929 clk_disable_unprepare(i2c->clk); 930 err_pclk: 931 clk_disable_unprepare(i2c->pclk); 932 return ret; 933 } 934 935 static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = { 936 NOIRQ_SYSTEM_SLEEP_PM_OPS(exynos5_i2c_suspend_noirq, 937 exynos5_i2c_resume_noirq) 938 }; 939 940 static struct platform_driver exynos5_i2c_driver = { 941 .probe = exynos5_i2c_probe, 942 .remove_new = exynos5_i2c_remove, 943 .driver = { 944 .name = "exynos5-hsi2c", 945 .pm = pm_sleep_ptr(&exynos5_i2c_dev_pm_ops), 946 .of_match_table = exynos5_i2c_match, 947 }, 948 }; 949 950 module_platform_driver(exynos5_i2c_driver); 951 952 MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver"); 953 MODULE_AUTHOR("Naveen Krishna Chatradhi <ch.naveen@samsung.com>"); 954 MODULE_AUTHOR("Taekgyun Ko <taeggyun.ko@samsung.com>"); 955 MODULE_LICENSE("GPL v2"); 956