1 /** 2 * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver 3 * 4 * Copyright (C) 2013 Samsung Electronics Co., Ltd. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 */ 10 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 14 #include <linux/i2c.h> 15 #include <linux/time.h> 16 #include <linux/interrupt.h> 17 #include <linux/delay.h> 18 #include <linux/errno.h> 19 #include <linux/err.h> 20 #include <linux/platform_device.h> 21 #include <linux/clk.h> 22 #include <linux/slab.h> 23 #include <linux/io.h> 24 #include <linux/of_address.h> 25 #include <linux/of_irq.h> 26 #include <linux/spinlock.h> 27 28 /* 29 * HSI2C controller from Samsung supports 2 modes of operation 30 * 1. Auto mode: Where in master automatically controls the whole transaction 31 * 2. Manual mode: Software controls the transaction by issuing commands 32 * START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register. 33 * 34 * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register 35 * 36 * Special bits are available for both modes of operation to set commands 37 * and for checking transfer status 38 */ 39 40 /* Register Map */ 41 #define HSI2C_CTL 0x00 42 #define HSI2C_FIFO_CTL 0x04 43 #define HSI2C_TRAILIG_CTL 0x08 44 #define HSI2C_CLK_CTL 0x0C 45 #define HSI2C_CLK_SLOT 0x10 46 #define HSI2C_INT_ENABLE 0x20 47 #define HSI2C_INT_STATUS 0x24 48 #define HSI2C_ERR_STATUS 0x2C 49 #define HSI2C_FIFO_STATUS 0x30 50 #define HSI2C_TX_DATA 0x34 51 #define HSI2C_RX_DATA 0x38 52 #define HSI2C_CONF 0x40 53 #define HSI2C_AUTO_CONF 0x44 54 #define HSI2C_TIMEOUT 0x48 55 #define HSI2C_MANUAL_CMD 0x4C 56 #define HSI2C_TRANS_STATUS 0x50 57 #define HSI2C_TIMING_HS1 0x54 58 #define HSI2C_TIMING_HS2 0x58 59 #define HSI2C_TIMING_HS3 0x5C 60 #define HSI2C_TIMING_FS1 0x60 61 #define HSI2C_TIMING_FS2 0x64 62 #define HSI2C_TIMING_FS3 0x68 63 #define HSI2C_TIMING_SLA 0x6C 64 #define HSI2C_ADDR 0x70 65 66 /* I2C_CTL Register bits */ 67 #define HSI2C_FUNC_MODE_I2C (1u << 0) 68 #define HSI2C_MASTER (1u << 3) 69 #define HSI2C_RXCHON (1u << 6) 70 #define HSI2C_TXCHON (1u << 7) 71 #define HSI2C_SW_RST (1u << 31) 72 73 /* I2C_FIFO_CTL Register bits */ 74 #define HSI2C_RXFIFO_EN (1u << 0) 75 #define HSI2C_TXFIFO_EN (1u << 1) 76 #define HSI2C_RXFIFO_TRIGGER_LEVEL(x) ((x) << 4) 77 #define HSI2C_TXFIFO_TRIGGER_LEVEL(x) ((x) << 16) 78 79 /* I2C_TRAILING_CTL Register bits */ 80 #define HSI2C_TRAILING_COUNT (0xf) 81 82 /* I2C_INT_EN Register bits */ 83 #define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0) 84 #define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1) 85 #define HSI2C_INT_TRAILING_EN (1u << 6) 86 #define HSI2C_INT_I2C_EN (1u << 9) 87 88 /* I2C_INT_STAT Register bits */ 89 #define HSI2C_INT_TX_ALMOSTEMPTY (1u << 0) 90 #define HSI2C_INT_RX_ALMOSTFULL (1u << 1) 91 #define HSI2C_INT_TX_UNDERRUN (1u << 2) 92 #define HSI2C_INT_TX_OVERRUN (1u << 3) 93 #define HSI2C_INT_RX_UNDERRUN (1u << 4) 94 #define HSI2C_INT_RX_OVERRUN (1u << 5) 95 #define HSI2C_INT_TRAILING (1u << 6) 96 #define HSI2C_INT_I2C (1u << 9) 97 98 /* I2C_FIFO_STAT Register bits */ 99 #define HSI2C_RX_FIFO_EMPTY (1u << 24) 100 #define HSI2C_RX_FIFO_FULL (1u << 23) 101 #define HSI2C_RX_FIFO_LVL(x) ((x >> 16) & 0x7f) 102 #define HSI2C_TX_FIFO_EMPTY (1u << 8) 103 #define HSI2C_TX_FIFO_FULL (1u << 7) 104 #define HSI2C_TX_FIFO_LVL(x) ((x >> 0) & 0x7f) 105 106 /* I2C_CONF Register bits */ 107 #define HSI2C_AUTO_MODE (1u << 31) 108 #define HSI2C_10BIT_ADDR_MODE (1u << 30) 109 #define HSI2C_HS_MODE (1u << 29) 110 111 /* I2C_AUTO_CONF Register bits */ 112 #define HSI2C_READ_WRITE (1u << 16) 113 #define HSI2C_STOP_AFTER_TRANS (1u << 17) 114 #define HSI2C_MASTER_RUN (1u << 31) 115 116 /* I2C_TIMEOUT Register bits */ 117 #define HSI2C_TIMEOUT_EN (1u << 31) 118 #define HSI2C_TIMEOUT_MASK 0xff 119 120 /* I2C_TRANS_STATUS register bits */ 121 #define HSI2C_MASTER_BUSY (1u << 17) 122 #define HSI2C_SLAVE_BUSY (1u << 16) 123 #define HSI2C_TIMEOUT_AUTO (1u << 4) 124 #define HSI2C_NO_DEV (1u << 3) 125 #define HSI2C_NO_DEV_ACK (1u << 2) 126 #define HSI2C_TRANS_ABORT (1u << 1) 127 #define HSI2C_TRANS_DONE (1u << 0) 128 129 /* I2C_ADDR register bits */ 130 #define HSI2C_SLV_ADDR_SLV(x) ((x & 0x3ff) << 0) 131 #define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10) 132 #define HSI2C_MASTER_ID(x) ((x & 0xff) << 24) 133 #define MASTER_ID(x) ((x & 0x7) + 0x08) 134 135 /* 136 * Controller operating frequency, timing values for operation 137 * are calculated against this frequency 138 */ 139 #define HSI2C_HS_TX_CLOCK 1000000 140 #define HSI2C_FS_TX_CLOCK 100000 141 #define HSI2C_HIGH_SPD 1 142 #define HSI2C_FAST_SPD 0 143 144 #define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000)) 145 146 struct exynos5_i2c { 147 struct i2c_adapter adap; 148 unsigned int suspended:1; 149 150 struct i2c_msg *msg; 151 struct completion msg_complete; 152 unsigned int msg_ptr; 153 154 unsigned int irq; 155 156 void __iomem *regs; 157 struct clk *clk; 158 struct device *dev; 159 int state; 160 161 spinlock_t lock; /* IRQ synchronization */ 162 163 /* 164 * Since the TRANS_DONE bit is cleared on read, and we may read it 165 * either during an IRQ or after a transaction, keep track of its 166 * state here. 167 */ 168 int trans_done; 169 170 /* Controller operating frequency */ 171 unsigned int fs_clock; 172 unsigned int hs_clock; 173 174 /* 175 * HSI2C Controller can operate in 176 * 1. High speed upto 3.4Mbps 177 * 2. Fast speed upto 1Mbps 178 */ 179 int speed_mode; 180 181 /* Version of HS-I2C Hardware */ 182 struct exynos_hsi2c_variant *variant; 183 }; 184 185 /** 186 * struct exynos_hsi2c_variant - platform specific HSI2C driver data 187 * @fifo_depth: the fifo depth supported by the HSI2C module 188 * 189 * Specifies platform specific configuration of HSI2C module. 190 * Note: A structure for driver specific platform data is used for future 191 * expansion of its usage. 192 */ 193 struct exynos_hsi2c_variant { 194 unsigned int fifo_depth; 195 }; 196 197 static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = { 198 .fifo_depth = 64, 199 }; 200 201 static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = { 202 .fifo_depth = 16, 203 }; 204 205 static const struct of_device_id exynos5_i2c_match[] = { 206 { 207 .compatible = "samsung,exynos5-hsi2c", 208 .data = &exynos5250_hsi2c_data 209 }, { 210 .compatible = "samsung,exynos5250-hsi2c", 211 .data = &exynos5250_hsi2c_data 212 }, { 213 .compatible = "samsung,exynos5260-hsi2c", 214 .data = &exynos5260_hsi2c_data 215 }, {}, 216 }; 217 MODULE_DEVICE_TABLE(of, exynos5_i2c_match); 218 219 static inline struct exynos_hsi2c_variant *exynos5_i2c_get_variant 220 (struct platform_device *pdev) 221 { 222 const struct of_device_id *match; 223 224 match = of_match_node(exynos5_i2c_match, pdev->dev.of_node); 225 return (struct exynos_hsi2c_variant *)match->data; 226 } 227 228 static void exynos5_i2c_clr_pend_irq(struct exynos5_i2c *i2c) 229 { 230 writel(readl(i2c->regs + HSI2C_INT_STATUS), 231 i2c->regs + HSI2C_INT_STATUS); 232 } 233 234 /* 235 * exynos5_i2c_set_timing: updates the registers with appropriate 236 * timing values calculated 237 * 238 * Returns 0 on success, -EINVAL if the cycle length cannot 239 * be calculated. 240 */ 241 static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, int mode) 242 { 243 u32 i2c_timing_s1; 244 u32 i2c_timing_s2; 245 u32 i2c_timing_s3; 246 u32 i2c_timing_sla; 247 unsigned int t_start_su, t_start_hd; 248 unsigned int t_stop_su; 249 unsigned int t_data_su, t_data_hd; 250 unsigned int t_scl_l, t_scl_h; 251 unsigned int t_sr_release; 252 unsigned int t_ftl_cycle; 253 unsigned int clkin = clk_get_rate(i2c->clk); 254 unsigned int div, utemp0 = 0, utemp1 = 0, clk_cycle; 255 unsigned int op_clk = (mode == HSI2C_HIGH_SPD) ? 256 i2c->hs_clock : i2c->fs_clock; 257 258 /* 259 * FPCLK / FI2C = 260 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE 261 * utemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) 262 * utemp1 = (TSCLK_L + TSCLK_H + 2) 263 */ 264 t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7; 265 utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle; 266 267 /* CLK_DIV max is 256 */ 268 for (div = 0; div < 256; div++) { 269 utemp1 = utemp0 / (div + 1); 270 271 /* 272 * SCL_L and SCL_H each has max value of 255 273 * Hence, For the clk_cycle to the have right value 274 * utemp1 has to be less then 512 and more than 4. 275 */ 276 if ((utemp1 < 512) && (utemp1 > 4)) { 277 clk_cycle = utemp1 - 2; 278 break; 279 } else if (div == 255) { 280 dev_warn(i2c->dev, "Failed to calculate divisor"); 281 return -EINVAL; 282 } 283 } 284 285 t_scl_l = clk_cycle / 2; 286 t_scl_h = clk_cycle / 2; 287 t_start_su = t_scl_l; 288 t_start_hd = t_scl_l; 289 t_stop_su = t_scl_l; 290 t_data_su = t_scl_l / 2; 291 t_data_hd = t_scl_l / 2; 292 t_sr_release = clk_cycle; 293 294 i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8; 295 i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0; 296 i2c_timing_s3 = div << 16 | t_sr_release << 0; 297 i2c_timing_sla = t_data_hd << 0; 298 299 dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n", 300 t_start_su, t_start_hd, t_stop_su); 301 dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n", 302 t_data_su, t_scl_l, t_scl_h); 303 dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n", 304 div, t_sr_release); 305 dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd); 306 307 if (mode == HSI2C_HIGH_SPD) { 308 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1); 309 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2); 310 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3); 311 } else { 312 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1); 313 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2); 314 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3); 315 } 316 writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA); 317 318 return 0; 319 } 320 321 static int exynos5_hsi2c_clock_setup(struct exynos5_i2c *i2c) 322 { 323 /* 324 * Configure the Fast speed timing values 325 * Even the High Speed mode initially starts with Fast mode 326 */ 327 if (exynos5_i2c_set_timing(i2c, HSI2C_FAST_SPD)) { 328 dev_err(i2c->dev, "HSI2C FS Clock set up failed\n"); 329 return -EINVAL; 330 } 331 332 /* configure the High speed timing values */ 333 if (i2c->speed_mode == HSI2C_HIGH_SPD) { 334 if (exynos5_i2c_set_timing(i2c, HSI2C_HIGH_SPD)) { 335 dev_err(i2c->dev, "HSI2C HS Clock set up failed\n"); 336 return -EINVAL; 337 } 338 } 339 340 return 0; 341 } 342 343 /* 344 * exynos5_i2c_init: configures the controller for I2C functionality 345 * Programs I2C controller for Master mode operation 346 */ 347 static void exynos5_i2c_init(struct exynos5_i2c *i2c) 348 { 349 u32 i2c_conf = readl(i2c->regs + HSI2C_CONF); 350 u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT); 351 352 /* Clear to disable Timeout */ 353 i2c_timeout &= ~HSI2C_TIMEOUT_EN; 354 writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT); 355 356 writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER), 357 i2c->regs + HSI2C_CTL); 358 writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL); 359 360 if (i2c->speed_mode == HSI2C_HIGH_SPD) { 361 writel(HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)), 362 i2c->regs + HSI2C_ADDR); 363 i2c_conf |= HSI2C_HS_MODE; 364 } 365 366 writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF); 367 } 368 369 static void exynos5_i2c_reset(struct exynos5_i2c *i2c) 370 { 371 u32 i2c_ctl; 372 373 /* Set and clear the bit for reset */ 374 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 375 i2c_ctl |= HSI2C_SW_RST; 376 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 377 378 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 379 i2c_ctl &= ~HSI2C_SW_RST; 380 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 381 382 /* We don't expect calculations to fail during the run */ 383 exynos5_hsi2c_clock_setup(i2c); 384 /* Initialize the configure registers */ 385 exynos5_i2c_init(i2c); 386 } 387 388 /* 389 * exynos5_i2c_irq: top level IRQ servicing routine 390 * 391 * INT_STATUS registers gives the interrupt details. Further, 392 * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed 393 * state of the bus. 394 */ 395 static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id) 396 { 397 struct exynos5_i2c *i2c = dev_id; 398 u32 fifo_level, int_status, fifo_status, trans_status; 399 unsigned char byte; 400 int len = 0; 401 402 i2c->state = -EINVAL; 403 404 spin_lock(&i2c->lock); 405 406 int_status = readl(i2c->regs + HSI2C_INT_STATUS); 407 writel(int_status, i2c->regs + HSI2C_INT_STATUS); 408 409 /* handle interrupt related to the transfer status */ 410 if (int_status & HSI2C_INT_I2C) { 411 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 412 if (trans_status & HSI2C_NO_DEV_ACK) { 413 dev_dbg(i2c->dev, "No ACK from device\n"); 414 i2c->state = -ENXIO; 415 goto stop; 416 } else if (trans_status & HSI2C_NO_DEV) { 417 dev_dbg(i2c->dev, "No device\n"); 418 i2c->state = -ENXIO; 419 goto stop; 420 } else if (trans_status & HSI2C_TRANS_ABORT) { 421 dev_dbg(i2c->dev, "Deal with arbitration lose\n"); 422 i2c->state = -EAGAIN; 423 goto stop; 424 } else if (trans_status & HSI2C_TIMEOUT_AUTO) { 425 dev_dbg(i2c->dev, "Accessing device timed out\n"); 426 i2c->state = -EAGAIN; 427 goto stop; 428 } else if (trans_status & HSI2C_TRANS_DONE) { 429 i2c->trans_done = 1; 430 i2c->state = 0; 431 } 432 } 433 434 if ((i2c->msg->flags & I2C_M_RD) && (int_status & 435 (HSI2C_INT_TRAILING | HSI2C_INT_RX_ALMOSTFULL))) { 436 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 437 fifo_level = HSI2C_RX_FIFO_LVL(fifo_status); 438 len = min(fifo_level, i2c->msg->len - i2c->msg_ptr); 439 440 while (len > 0) { 441 byte = (unsigned char) 442 readl(i2c->regs + HSI2C_RX_DATA); 443 i2c->msg->buf[i2c->msg_ptr++] = byte; 444 len--; 445 } 446 i2c->state = 0; 447 } else if (int_status & HSI2C_INT_TX_ALMOSTEMPTY) { 448 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 449 fifo_level = HSI2C_TX_FIFO_LVL(fifo_status); 450 451 len = i2c->variant->fifo_depth - fifo_level; 452 if (len > (i2c->msg->len - i2c->msg_ptr)) 453 len = i2c->msg->len - i2c->msg_ptr; 454 455 while (len > 0) { 456 byte = i2c->msg->buf[i2c->msg_ptr++]; 457 writel(byte, i2c->regs + HSI2C_TX_DATA); 458 len--; 459 } 460 i2c->state = 0; 461 } 462 463 stop: 464 if ((i2c->trans_done && (i2c->msg->len == i2c->msg_ptr)) || 465 (i2c->state < 0)) { 466 writel(0, i2c->regs + HSI2C_INT_ENABLE); 467 exynos5_i2c_clr_pend_irq(i2c); 468 complete(&i2c->msg_complete); 469 } 470 471 spin_unlock(&i2c->lock); 472 473 return IRQ_HANDLED; 474 } 475 476 /* 477 * exynos5_i2c_wait_bus_idle 478 * 479 * Wait for the bus to go idle, indicated by the MASTER_BUSY bit being 480 * cleared. 481 * 482 * Returns -EBUSY if the bus cannot be bought to idle 483 */ 484 static int exynos5_i2c_wait_bus_idle(struct exynos5_i2c *i2c) 485 { 486 unsigned long stop_time; 487 u32 trans_status; 488 489 /* wait for 100 milli seconds for the bus to be idle */ 490 stop_time = jiffies + msecs_to_jiffies(100) + 1; 491 do { 492 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 493 if (!(trans_status & HSI2C_MASTER_BUSY)) 494 return 0; 495 496 usleep_range(50, 200); 497 } while (time_before(jiffies, stop_time)); 498 499 return -EBUSY; 500 } 501 502 /* 503 * exynos5_i2c_message_start: Configures the bus and starts the xfer 504 * i2c: struct exynos5_i2c pointer for the current bus 505 * stop: Enables stop after transfer if set. Set for last transfer of 506 * in the list of messages. 507 * 508 * Configures the bus for read/write function 509 * Sets chip address to talk to, message length to be sent. 510 * Enables appropriate interrupts and sends start xfer command. 511 */ 512 static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop) 513 { 514 u32 i2c_ctl; 515 u32 int_en = HSI2C_INT_I2C_EN; 516 u32 i2c_auto_conf = 0; 517 u32 fifo_ctl; 518 unsigned long flags; 519 unsigned short trig_lvl; 520 521 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 522 i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON); 523 fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN; 524 525 if (i2c->msg->flags & I2C_M_RD) { 526 i2c_ctl |= HSI2C_RXCHON; 527 528 i2c_auto_conf |= HSI2C_READ_WRITE; 529 530 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 531 (i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len; 532 fifo_ctl |= HSI2C_RXFIFO_TRIGGER_LEVEL(trig_lvl); 533 534 int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN | 535 HSI2C_INT_TRAILING_EN); 536 } else { 537 i2c_ctl |= HSI2C_TXCHON; 538 539 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 540 (i2c->variant->fifo_depth * 1 / 4) : i2c->msg->len; 541 fifo_ctl |= HSI2C_TXFIFO_TRIGGER_LEVEL(trig_lvl); 542 543 int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN; 544 } 545 546 writel(HSI2C_SLV_ADDR_MAS(i2c->msg->addr), i2c->regs + HSI2C_ADDR); 547 548 writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL); 549 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 550 551 /* 552 * Enable interrupts before starting the transfer so that we don't 553 * miss any INT_I2C interrupts. 554 */ 555 spin_lock_irqsave(&i2c->lock, flags); 556 writel(int_en, i2c->regs + HSI2C_INT_ENABLE); 557 558 if (stop == 1) 559 i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS; 560 i2c_auto_conf |= i2c->msg->len; 561 i2c_auto_conf |= HSI2C_MASTER_RUN; 562 writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF); 563 spin_unlock_irqrestore(&i2c->lock, flags); 564 } 565 566 static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c, 567 struct i2c_msg *msgs, int stop) 568 { 569 unsigned long timeout; 570 int ret; 571 572 i2c->msg = msgs; 573 i2c->msg_ptr = 0; 574 i2c->trans_done = 0; 575 576 reinit_completion(&i2c->msg_complete); 577 578 exynos5_i2c_message_start(i2c, stop); 579 580 timeout = wait_for_completion_timeout(&i2c->msg_complete, 581 EXYNOS5_I2C_TIMEOUT); 582 if (timeout == 0) 583 ret = -ETIMEDOUT; 584 else 585 ret = i2c->state; 586 587 /* 588 * If this is the last message to be transfered (stop == 1) 589 * Then check if the bus can be brought back to idle. 590 */ 591 if (ret == 0 && stop) 592 ret = exynos5_i2c_wait_bus_idle(i2c); 593 594 if (ret < 0) { 595 exynos5_i2c_reset(i2c); 596 if (ret == -ETIMEDOUT) 597 dev_warn(i2c->dev, "%s timeout\n", 598 (msgs->flags & I2C_M_RD) ? "rx" : "tx"); 599 } 600 601 /* Return the state as in interrupt routine */ 602 return ret; 603 } 604 605 static int exynos5_i2c_xfer(struct i2c_adapter *adap, 606 struct i2c_msg *msgs, int num) 607 { 608 struct exynos5_i2c *i2c = adap->algo_data; 609 int i = 0, ret = 0, stop = 0; 610 611 if (i2c->suspended) { 612 dev_err(i2c->dev, "HS-I2C is not initialized.\n"); 613 return -EIO; 614 } 615 616 clk_prepare_enable(i2c->clk); 617 618 for (i = 0; i < num; i++, msgs++) { 619 stop = (i == num - 1); 620 621 ret = exynos5_i2c_xfer_msg(i2c, msgs, stop); 622 623 if (ret < 0) 624 goto out; 625 } 626 627 if (i == num) { 628 ret = num; 629 } else { 630 /* Only one message, cannot access the device */ 631 if (i == 1) 632 ret = -EREMOTEIO; 633 else 634 ret = i; 635 636 dev_warn(i2c->dev, "xfer message failed\n"); 637 } 638 639 out: 640 clk_disable_unprepare(i2c->clk); 641 return ret; 642 } 643 644 static u32 exynos5_i2c_func(struct i2c_adapter *adap) 645 { 646 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); 647 } 648 649 static const struct i2c_algorithm exynos5_i2c_algorithm = { 650 .master_xfer = exynos5_i2c_xfer, 651 .functionality = exynos5_i2c_func, 652 }; 653 654 static int exynos5_i2c_probe(struct platform_device *pdev) 655 { 656 struct device_node *np = pdev->dev.of_node; 657 struct exynos5_i2c *i2c; 658 struct resource *mem; 659 unsigned int op_clock; 660 int ret; 661 662 i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL); 663 if (!i2c) 664 return -ENOMEM; 665 666 if (of_property_read_u32(np, "clock-frequency", &op_clock)) { 667 i2c->speed_mode = HSI2C_FAST_SPD; 668 i2c->fs_clock = HSI2C_FS_TX_CLOCK; 669 } else { 670 if (op_clock >= HSI2C_HS_TX_CLOCK) { 671 i2c->speed_mode = HSI2C_HIGH_SPD; 672 i2c->fs_clock = HSI2C_FS_TX_CLOCK; 673 i2c->hs_clock = op_clock; 674 } else { 675 i2c->speed_mode = HSI2C_FAST_SPD; 676 i2c->fs_clock = op_clock; 677 } 678 } 679 680 strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name)); 681 i2c->adap.owner = THIS_MODULE; 682 i2c->adap.algo = &exynos5_i2c_algorithm; 683 i2c->adap.retries = 3; 684 685 i2c->dev = &pdev->dev; 686 i2c->clk = devm_clk_get(&pdev->dev, "hsi2c"); 687 if (IS_ERR(i2c->clk)) { 688 dev_err(&pdev->dev, "cannot get clock\n"); 689 return -ENOENT; 690 } 691 692 clk_prepare_enable(i2c->clk); 693 694 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 695 i2c->regs = devm_ioremap_resource(&pdev->dev, mem); 696 if (IS_ERR(i2c->regs)) { 697 ret = PTR_ERR(i2c->regs); 698 goto err_clk; 699 } 700 701 i2c->adap.dev.of_node = np; 702 i2c->adap.algo_data = i2c; 703 i2c->adap.dev.parent = &pdev->dev; 704 705 /* Clear pending interrupts from u-boot or misc causes */ 706 exynos5_i2c_clr_pend_irq(i2c); 707 708 spin_lock_init(&i2c->lock); 709 init_completion(&i2c->msg_complete); 710 711 i2c->irq = ret = platform_get_irq(pdev, 0); 712 if (ret <= 0) { 713 dev_err(&pdev->dev, "cannot find HS-I2C IRQ\n"); 714 ret = -EINVAL; 715 goto err_clk; 716 } 717 718 ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq, 719 IRQF_NO_SUSPEND | IRQF_ONESHOT, 720 dev_name(&pdev->dev), i2c); 721 722 if (ret != 0) { 723 dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq); 724 goto err_clk; 725 } 726 727 ret = exynos5_hsi2c_clock_setup(i2c); 728 if (ret) 729 goto err_clk; 730 731 i2c->variant = exynos5_i2c_get_variant(pdev); 732 733 exynos5_i2c_reset(i2c); 734 735 ret = i2c_add_adapter(&i2c->adap); 736 if (ret < 0) { 737 dev_err(&pdev->dev, "failed to add bus to i2c core\n"); 738 goto err_clk; 739 } 740 741 platform_set_drvdata(pdev, i2c); 742 743 err_clk: 744 clk_disable_unprepare(i2c->clk); 745 return ret; 746 } 747 748 static int exynos5_i2c_remove(struct platform_device *pdev) 749 { 750 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 751 752 i2c_del_adapter(&i2c->adap); 753 754 return 0; 755 } 756 757 #ifdef CONFIG_PM_SLEEP 758 static int exynos5_i2c_suspend_noirq(struct device *dev) 759 { 760 struct platform_device *pdev = to_platform_device(dev); 761 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 762 763 i2c->suspended = 1; 764 765 return 0; 766 } 767 768 static int exynos5_i2c_resume_noirq(struct device *dev) 769 { 770 struct platform_device *pdev = to_platform_device(dev); 771 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 772 int ret = 0; 773 774 clk_prepare_enable(i2c->clk); 775 776 ret = exynos5_hsi2c_clock_setup(i2c); 777 if (ret) { 778 clk_disable_unprepare(i2c->clk); 779 return ret; 780 } 781 782 exynos5_i2c_init(i2c); 783 clk_disable_unprepare(i2c->clk); 784 i2c->suspended = 0; 785 786 return 0; 787 } 788 #endif 789 790 static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = { 791 #ifdef CONFIG_PM_SLEEP 792 .suspend_noirq = exynos5_i2c_suspend_noirq, 793 .resume_noirq = exynos5_i2c_resume_noirq, 794 .freeze_noirq = exynos5_i2c_suspend_noirq, 795 .thaw_noirq = exynos5_i2c_resume_noirq, 796 .poweroff_noirq = exynos5_i2c_suspend_noirq, 797 .restore_noirq = exynos5_i2c_resume_noirq, 798 #endif 799 }; 800 801 static struct platform_driver exynos5_i2c_driver = { 802 .probe = exynos5_i2c_probe, 803 .remove = exynos5_i2c_remove, 804 .driver = { 805 .owner = THIS_MODULE, 806 .name = "exynos5-hsi2c", 807 .pm = &exynos5_i2c_dev_pm_ops, 808 .of_match_table = exynos5_i2c_match, 809 }, 810 }; 811 812 module_platform_driver(exynos5_i2c_driver); 813 814 MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver"); 815 MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>"); 816 MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>"); 817 MODULE_LICENSE("GPL v2"); 818