1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Synopsys DesignWare I2C adapter driver (master only). 4 * 5 * Based on the TI DAVINCI I2C adapter driver. 6 * 7 * Copyright (C) 2006 Texas Instruments. 8 * Copyright (C) 2007 MontaVista Software Inc. 9 * Copyright (C) 2009 Provigent Ltd. 10 */ 11 #include <linux/delay.h> 12 #include <linux/err.h> 13 #include <linux/errno.h> 14 #include <linux/export.h> 15 #include <linux/gpio/consumer.h> 16 #include <linux/i2c.h> 17 #include <linux/interrupt.h> 18 #include <linux/io.h> 19 #include <linux/module.h> 20 #include <linux/pm_runtime.h> 21 #include <linux/reset.h> 22 23 #include "i2c-designware-core.h" 24 25 static void i2c_dw_configure_fifo_master(struct dw_i2c_dev *dev) 26 { 27 /* Configure Tx/Rx FIFO threshold levels */ 28 dw_writel(dev, dev->tx_fifo_depth / 2, DW_IC_TX_TL); 29 dw_writel(dev, 0, DW_IC_RX_TL); 30 31 /* Configure the I2C master */ 32 dw_writel(dev, dev->master_cfg, DW_IC_CON); 33 } 34 35 static int i2c_dw_set_timings_master(struct dw_i2c_dev *dev) 36 { 37 const char *mode_str, *fp_str = ""; 38 u32 comp_param1; 39 u32 sda_falling_time, scl_falling_time; 40 struct i2c_timings *t = &dev->timings; 41 u32 ic_clk; 42 int ret; 43 44 ret = i2c_dw_acquire_lock(dev); 45 if (ret) 46 return ret; 47 comp_param1 = dw_readl(dev, DW_IC_COMP_PARAM_1); 48 i2c_dw_release_lock(dev); 49 50 /* Set standard and fast speed dividers for high/low periods */ 51 sda_falling_time = t->sda_fall_ns ?: 300; /* ns */ 52 scl_falling_time = t->scl_fall_ns ?: 300; /* ns */ 53 54 /* Calculate SCL timing parameters for standard mode if not set */ 55 if (!dev->ss_hcnt || !dev->ss_lcnt) { 56 ic_clk = i2c_dw_clk_rate(dev); 57 dev->ss_hcnt = 58 i2c_dw_scl_hcnt(ic_clk, 59 4000, /* tHD;STA = tHIGH = 4.0 us */ 60 sda_falling_time, 61 0, /* 0: DW default, 1: Ideal */ 62 0); /* No offset */ 63 dev->ss_lcnt = 64 i2c_dw_scl_lcnt(ic_clk, 65 4700, /* tLOW = 4.7 us */ 66 scl_falling_time, 67 0); /* No offset */ 68 } 69 dev_dbg(dev->dev, "Standard Mode HCNT:LCNT = %d:%d\n", 70 dev->ss_hcnt, dev->ss_lcnt); 71 72 /* 73 * Set SCL timing parameters for fast mode or fast mode plus. Only 74 * difference is the timing parameter values since the registers are 75 * the same. 76 */ 77 if (t->bus_freq_hz == 1000000) { 78 /* 79 * Check are fast mode plus parameters available and use 80 * fast mode if not. 81 */ 82 if (dev->fp_hcnt && dev->fp_lcnt) { 83 dev->fs_hcnt = dev->fp_hcnt; 84 dev->fs_lcnt = dev->fp_lcnt; 85 fp_str = " Plus"; 86 } 87 } 88 /* 89 * Calculate SCL timing parameters for fast mode if not set. They are 90 * needed also in high speed mode. 91 */ 92 if (!dev->fs_hcnt || !dev->fs_lcnt) { 93 ic_clk = i2c_dw_clk_rate(dev); 94 dev->fs_hcnt = 95 i2c_dw_scl_hcnt(ic_clk, 96 600, /* tHD;STA = tHIGH = 0.6 us */ 97 sda_falling_time, 98 0, /* 0: DW default, 1: Ideal */ 99 0); /* No offset */ 100 dev->fs_lcnt = 101 i2c_dw_scl_lcnt(ic_clk, 102 1300, /* tLOW = 1.3 us */ 103 scl_falling_time, 104 0); /* No offset */ 105 } 106 dev_dbg(dev->dev, "Fast Mode%s HCNT:LCNT = %d:%d\n", 107 fp_str, dev->fs_hcnt, dev->fs_lcnt); 108 109 /* Check is high speed possible and fall back to fast mode if not */ 110 if ((dev->master_cfg & DW_IC_CON_SPEED_MASK) == 111 DW_IC_CON_SPEED_HIGH) { 112 if ((comp_param1 & DW_IC_COMP_PARAM_1_SPEED_MODE_MASK) 113 != DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH) { 114 dev_err(dev->dev, "High Speed not supported!\n"); 115 dev->master_cfg &= ~DW_IC_CON_SPEED_MASK; 116 dev->master_cfg |= DW_IC_CON_SPEED_FAST; 117 dev->hs_hcnt = 0; 118 dev->hs_lcnt = 0; 119 } else if (dev->hs_hcnt && dev->hs_lcnt) { 120 dev_dbg(dev->dev, "High Speed Mode HCNT:LCNT = %d:%d\n", 121 dev->hs_hcnt, dev->hs_lcnt); 122 } 123 } 124 125 ret = i2c_dw_set_sda_hold(dev); 126 if (ret) 127 goto out; 128 129 switch (dev->master_cfg & DW_IC_CON_SPEED_MASK) { 130 case DW_IC_CON_SPEED_STD: 131 mode_str = "Standard Mode"; 132 break; 133 case DW_IC_CON_SPEED_HIGH: 134 mode_str = "High Speed Mode"; 135 break; 136 default: 137 mode_str = "Fast Mode"; 138 } 139 dev_dbg(dev->dev, "Bus speed: %s%s\n", mode_str, fp_str); 140 141 out: 142 return ret; 143 } 144 145 /** 146 * i2c_dw_init() - Initialize the designware I2C master hardware 147 * @dev: device private data 148 * 149 * This functions configures and enables the I2C master. 150 * This function is called during I2C init function, and in case of timeout at 151 * run time. 152 */ 153 static int i2c_dw_init_master(struct dw_i2c_dev *dev) 154 { 155 int ret; 156 157 ret = i2c_dw_acquire_lock(dev); 158 if (ret) 159 return ret; 160 161 /* Disable the adapter */ 162 __i2c_dw_disable(dev); 163 164 /* Write standard speed timing parameters */ 165 dw_writel(dev, dev->ss_hcnt, DW_IC_SS_SCL_HCNT); 166 dw_writel(dev, dev->ss_lcnt, DW_IC_SS_SCL_LCNT); 167 168 /* Write fast mode/fast mode plus timing parameters */ 169 dw_writel(dev, dev->fs_hcnt, DW_IC_FS_SCL_HCNT); 170 dw_writel(dev, dev->fs_lcnt, DW_IC_FS_SCL_LCNT); 171 172 /* Write high speed timing parameters if supported */ 173 if (dev->hs_hcnt && dev->hs_lcnt) { 174 dw_writel(dev, dev->hs_hcnt, DW_IC_HS_SCL_HCNT); 175 dw_writel(dev, dev->hs_lcnt, DW_IC_HS_SCL_LCNT); 176 } 177 178 /* Write SDA hold time if supported */ 179 if (dev->sda_hold_time) 180 dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD); 181 182 i2c_dw_configure_fifo_master(dev); 183 i2c_dw_release_lock(dev); 184 185 return 0; 186 } 187 188 static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) 189 { 190 struct i2c_msg *msgs = dev->msgs; 191 u32 ic_con, ic_tar = 0; 192 193 /* Disable the adapter */ 194 __i2c_dw_disable(dev); 195 196 /* If the slave address is ten bit address, enable 10BITADDR */ 197 ic_con = dw_readl(dev, DW_IC_CON); 198 if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) { 199 ic_con |= DW_IC_CON_10BITADDR_MASTER; 200 /* 201 * If I2C_DYNAMIC_TAR_UPDATE is set, the 10-bit addressing 202 * mode has to be enabled via bit 12 of IC_TAR register. 203 * We set it always as I2C_DYNAMIC_TAR_UPDATE can't be 204 * detected from registers. 205 */ 206 ic_tar = DW_IC_TAR_10BITADDR_MASTER; 207 } else { 208 ic_con &= ~DW_IC_CON_10BITADDR_MASTER; 209 } 210 211 dw_writel(dev, ic_con, DW_IC_CON); 212 213 /* 214 * Set the slave (target) address and enable 10-bit addressing mode 215 * if applicable. 216 */ 217 dw_writel(dev, msgs[dev->msg_write_idx].addr | ic_tar, DW_IC_TAR); 218 219 /* Enforce disabled interrupts (due to HW issues) */ 220 i2c_dw_disable_int(dev); 221 222 /* Enable the adapter */ 223 __i2c_dw_enable(dev); 224 225 /* Dummy read to avoid the register getting stuck on Bay Trail */ 226 dw_readl(dev, DW_IC_ENABLE_STATUS); 227 228 /* Clear and enable interrupts */ 229 dw_readl(dev, DW_IC_CLR_INTR); 230 dw_writel(dev, DW_IC_INTR_MASTER_MASK, DW_IC_INTR_MASK); 231 } 232 233 /* 234 * Initiate (and continue) low level master read/write transaction. 235 * This function is only called from i2c_dw_isr, and pumping i2c_msg 236 * messages into the tx buffer. Even if the size of i2c_msg data is 237 * longer than the size of the tx buffer, it handles everything. 238 */ 239 static void 240 i2c_dw_xfer_msg(struct dw_i2c_dev *dev) 241 { 242 struct i2c_msg *msgs = dev->msgs; 243 u32 intr_mask; 244 int tx_limit, rx_limit; 245 u32 addr = msgs[dev->msg_write_idx].addr; 246 u32 buf_len = dev->tx_buf_len; 247 u8 *buf = dev->tx_buf; 248 bool need_restart = false; 249 250 intr_mask = DW_IC_INTR_MASTER_MASK; 251 252 for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) { 253 u32 flags = msgs[dev->msg_write_idx].flags; 254 255 /* 256 * If target address has changed, we need to 257 * reprogram the target address in the I2C 258 * adapter when we are done with this transfer. 259 */ 260 if (msgs[dev->msg_write_idx].addr != addr) { 261 dev_err(dev->dev, 262 "%s: invalid target address\n", __func__); 263 dev->msg_err = -EINVAL; 264 break; 265 } 266 267 if (!(dev->status & STATUS_WRITE_IN_PROGRESS)) { 268 /* new i2c_msg */ 269 buf = msgs[dev->msg_write_idx].buf; 270 buf_len = msgs[dev->msg_write_idx].len; 271 272 /* If both IC_EMPTYFIFO_HOLD_MASTER_EN and 273 * IC_RESTART_EN are set, we must manually 274 * set restart bit between messages. 275 */ 276 if ((dev->master_cfg & DW_IC_CON_RESTART_EN) && 277 (dev->msg_write_idx > 0)) 278 need_restart = true; 279 } 280 281 tx_limit = dev->tx_fifo_depth - dw_readl(dev, DW_IC_TXFLR); 282 rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR); 283 284 while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) { 285 u32 cmd = 0; 286 287 /* 288 * If IC_EMPTYFIFO_HOLD_MASTER_EN is set we must 289 * manually set the stop bit. However, it cannot be 290 * detected from the registers so we set it always 291 * when writing/reading the last byte. 292 */ 293 294 /* 295 * i2c-core always sets the buffer length of 296 * I2C_FUNC_SMBUS_BLOCK_DATA to 1. The length will 297 * be adjusted when receiving the first byte. 298 * Thus we can't stop the transaction here. 299 */ 300 if (dev->msg_write_idx == dev->msgs_num - 1 && 301 buf_len == 1 && !(flags & I2C_M_RECV_LEN)) 302 cmd |= BIT(9); 303 304 if (need_restart) { 305 cmd |= BIT(10); 306 need_restart = false; 307 } 308 309 if (msgs[dev->msg_write_idx].flags & I2C_M_RD) { 310 311 /* Avoid rx buffer overrun */ 312 if (dev->rx_outstanding >= dev->rx_fifo_depth) 313 break; 314 315 dw_writel(dev, cmd | 0x100, DW_IC_DATA_CMD); 316 rx_limit--; 317 dev->rx_outstanding++; 318 } else 319 dw_writel(dev, cmd | *buf++, DW_IC_DATA_CMD); 320 tx_limit--; buf_len--; 321 } 322 323 dev->tx_buf = buf; 324 dev->tx_buf_len = buf_len; 325 326 /* 327 * Because we don't know the buffer length in the 328 * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop 329 * the transaction here. 330 */ 331 if (buf_len > 0 || flags & I2C_M_RECV_LEN) { 332 /* more bytes to be written */ 333 dev->status |= STATUS_WRITE_IN_PROGRESS; 334 break; 335 } else 336 dev->status &= ~STATUS_WRITE_IN_PROGRESS; 337 } 338 339 /* 340 * If i2c_msg index search is completed, we don't need TX_EMPTY 341 * interrupt any more. 342 */ 343 if (dev->msg_write_idx == dev->msgs_num) 344 intr_mask &= ~DW_IC_INTR_TX_EMPTY; 345 346 if (dev->msg_err) 347 intr_mask = 0; 348 349 dw_writel(dev, intr_mask, DW_IC_INTR_MASK); 350 } 351 352 static u8 353 i2c_dw_recv_len(struct dw_i2c_dev *dev, u8 len) 354 { 355 struct i2c_msg *msgs = dev->msgs; 356 u32 flags = msgs[dev->msg_read_idx].flags; 357 358 /* 359 * Adjust the buffer length and mask the flag 360 * after receiving the first byte. 361 */ 362 len += (flags & I2C_CLIENT_PEC) ? 2 : 1; 363 dev->tx_buf_len = len - min_t(u8, len, dev->rx_outstanding); 364 msgs[dev->msg_read_idx].len = len; 365 msgs[dev->msg_read_idx].flags &= ~I2C_M_RECV_LEN; 366 367 return len; 368 } 369 370 static void 371 i2c_dw_read(struct dw_i2c_dev *dev) 372 { 373 struct i2c_msg *msgs = dev->msgs; 374 int rx_valid; 375 376 for (; dev->msg_read_idx < dev->msgs_num; dev->msg_read_idx++) { 377 u32 len; 378 u8 *buf; 379 380 if (!(msgs[dev->msg_read_idx].flags & I2C_M_RD)) 381 continue; 382 383 if (!(dev->status & STATUS_READ_IN_PROGRESS)) { 384 len = msgs[dev->msg_read_idx].len; 385 buf = msgs[dev->msg_read_idx].buf; 386 } else { 387 len = dev->rx_buf_len; 388 buf = dev->rx_buf; 389 } 390 391 rx_valid = dw_readl(dev, DW_IC_RXFLR); 392 393 for (; len > 0 && rx_valid > 0; len--, rx_valid--) { 394 u32 flags = msgs[dev->msg_read_idx].flags; 395 396 *buf = dw_readl(dev, DW_IC_DATA_CMD); 397 /* Ensure length byte is a valid value */ 398 if (flags & I2C_M_RECV_LEN && 399 *buf <= I2C_SMBUS_BLOCK_MAX && *buf > 0) { 400 len = i2c_dw_recv_len(dev, *buf); 401 } 402 buf++; 403 dev->rx_outstanding--; 404 } 405 406 if (len > 0) { 407 dev->status |= STATUS_READ_IN_PROGRESS; 408 dev->rx_buf_len = len; 409 dev->rx_buf = buf; 410 return; 411 } else 412 dev->status &= ~STATUS_READ_IN_PROGRESS; 413 } 414 } 415 416 /* 417 * Prepare controller for a transaction and call i2c_dw_xfer_msg. 418 */ 419 static int 420 i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) 421 { 422 struct dw_i2c_dev *dev = i2c_get_adapdata(adap); 423 int ret; 424 425 dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num); 426 427 pm_runtime_get_sync(dev->dev); 428 429 if (dev->suspended) { 430 dev_err(dev->dev, "Error %s call while suspended\n", __func__); 431 ret = -ESHUTDOWN; 432 goto done_nolock; 433 } 434 435 reinit_completion(&dev->cmd_complete); 436 dev->msgs = msgs; 437 dev->msgs_num = num; 438 dev->cmd_err = 0; 439 dev->msg_write_idx = 0; 440 dev->msg_read_idx = 0; 441 dev->msg_err = 0; 442 dev->status = STATUS_IDLE; 443 dev->abort_source = 0; 444 dev->rx_outstanding = 0; 445 446 ret = i2c_dw_acquire_lock(dev); 447 if (ret) 448 goto done_nolock; 449 450 ret = i2c_dw_wait_bus_not_busy(dev); 451 if (ret < 0) 452 goto done; 453 454 /* Start the transfers */ 455 i2c_dw_xfer_init(dev); 456 457 /* Wait for tx to complete */ 458 if (!wait_for_completion_timeout(&dev->cmd_complete, adap->timeout)) { 459 dev_err(dev->dev, "controller timed out\n"); 460 /* i2c_dw_init implicitly disables the adapter */ 461 i2c_recover_bus(&dev->adapter); 462 i2c_dw_init_master(dev); 463 ret = -ETIMEDOUT; 464 goto done; 465 } 466 467 /* 468 * We must disable the adapter before returning and signaling the end 469 * of the current transfer. Otherwise the hardware might continue 470 * generating interrupts which in turn causes a race condition with 471 * the following transfer. Needs some more investigation if the 472 * additional interrupts are a hardware bug or this driver doesn't 473 * handle them correctly yet. 474 */ 475 __i2c_dw_disable_nowait(dev); 476 477 if (dev->msg_err) { 478 ret = dev->msg_err; 479 goto done; 480 } 481 482 /* No error */ 483 if (likely(!dev->cmd_err && !dev->status)) { 484 ret = num; 485 goto done; 486 } 487 488 /* We have an error */ 489 if (dev->cmd_err == DW_IC_ERR_TX_ABRT) { 490 ret = i2c_dw_handle_tx_abort(dev); 491 goto done; 492 } 493 494 if (dev->status) 495 dev_err(dev->dev, 496 "transfer terminated early - interrupt latency too high?\n"); 497 498 ret = -EIO; 499 500 done: 501 i2c_dw_release_lock(dev); 502 503 done_nolock: 504 pm_runtime_mark_last_busy(dev->dev); 505 pm_runtime_put_autosuspend(dev->dev); 506 507 return ret; 508 } 509 510 static const struct i2c_algorithm i2c_dw_algo = { 511 .master_xfer = i2c_dw_xfer, 512 .functionality = i2c_dw_func, 513 }; 514 515 static const struct i2c_adapter_quirks i2c_dw_quirks = { 516 .flags = I2C_AQ_NO_ZERO_LEN, 517 }; 518 519 static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) 520 { 521 u32 stat; 522 523 /* 524 * The IC_INTR_STAT register just indicates "enabled" interrupts. 525 * Ths unmasked raw version of interrupt status bits are available 526 * in the IC_RAW_INTR_STAT register. 527 * 528 * That is, 529 * stat = dw_readl(IC_INTR_STAT); 530 * equals to, 531 * stat = dw_readl(IC_RAW_INTR_STAT) & dw_readl(IC_INTR_MASK); 532 * 533 * The raw version might be useful for debugging purposes. 534 */ 535 stat = dw_readl(dev, DW_IC_INTR_STAT); 536 537 /* 538 * Do not use the IC_CLR_INTR register to clear interrupts, or 539 * you'll miss some interrupts, triggered during the period from 540 * dw_readl(IC_INTR_STAT) to dw_readl(IC_CLR_INTR). 541 * 542 * Instead, use the separately-prepared IC_CLR_* registers. 543 */ 544 if (stat & DW_IC_INTR_RX_UNDER) 545 dw_readl(dev, DW_IC_CLR_RX_UNDER); 546 if (stat & DW_IC_INTR_RX_OVER) 547 dw_readl(dev, DW_IC_CLR_RX_OVER); 548 if (stat & DW_IC_INTR_TX_OVER) 549 dw_readl(dev, DW_IC_CLR_TX_OVER); 550 if (stat & DW_IC_INTR_RD_REQ) 551 dw_readl(dev, DW_IC_CLR_RD_REQ); 552 if (stat & DW_IC_INTR_TX_ABRT) { 553 /* 554 * The IC_TX_ABRT_SOURCE register is cleared whenever 555 * the IC_CLR_TX_ABRT is read. Preserve it beforehand. 556 */ 557 dev->abort_source = dw_readl(dev, DW_IC_TX_ABRT_SOURCE); 558 dw_readl(dev, DW_IC_CLR_TX_ABRT); 559 } 560 if (stat & DW_IC_INTR_RX_DONE) 561 dw_readl(dev, DW_IC_CLR_RX_DONE); 562 if (stat & DW_IC_INTR_ACTIVITY) 563 dw_readl(dev, DW_IC_CLR_ACTIVITY); 564 if (stat & DW_IC_INTR_STOP_DET) 565 dw_readl(dev, DW_IC_CLR_STOP_DET); 566 if (stat & DW_IC_INTR_START_DET) 567 dw_readl(dev, DW_IC_CLR_START_DET); 568 if (stat & DW_IC_INTR_GEN_CALL) 569 dw_readl(dev, DW_IC_CLR_GEN_CALL); 570 571 return stat; 572 } 573 574 /* 575 * Interrupt service routine. This gets called whenever an I2C master interrupt 576 * occurs. 577 */ 578 static int i2c_dw_irq_handler_master(struct dw_i2c_dev *dev) 579 { 580 u32 stat; 581 582 stat = i2c_dw_read_clear_intrbits(dev); 583 if (stat & DW_IC_INTR_TX_ABRT) { 584 dev->cmd_err |= DW_IC_ERR_TX_ABRT; 585 dev->status = STATUS_IDLE; 586 587 /* 588 * Anytime TX_ABRT is set, the contents of the tx/rx 589 * buffers are flushed. Make sure to skip them. 590 */ 591 dw_writel(dev, 0, DW_IC_INTR_MASK); 592 goto tx_aborted; 593 } 594 595 if (stat & DW_IC_INTR_RX_FULL) 596 i2c_dw_read(dev); 597 598 if (stat & DW_IC_INTR_TX_EMPTY) 599 i2c_dw_xfer_msg(dev); 600 601 /* 602 * No need to modify or disable the interrupt mask here. 603 * i2c_dw_xfer_msg() will take care of it according to 604 * the current transmit status. 605 */ 606 607 tx_aborted: 608 if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err) 609 complete(&dev->cmd_complete); 610 else if (unlikely(dev->flags & ACCESS_INTR_MASK)) { 611 /* Workaround to trigger pending interrupt */ 612 stat = dw_readl(dev, DW_IC_INTR_MASK); 613 i2c_dw_disable_int(dev); 614 dw_writel(dev, stat, DW_IC_INTR_MASK); 615 } 616 617 return 0; 618 } 619 620 static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) 621 { 622 struct dw_i2c_dev *dev = dev_id; 623 u32 stat, enabled; 624 625 enabled = dw_readl(dev, DW_IC_ENABLE); 626 stat = dw_readl(dev, DW_IC_RAW_INTR_STAT); 627 dev_dbg(dev->dev, "enabled=%#x stat=%#x\n", enabled, stat); 628 if (!enabled || !(stat & ~DW_IC_INTR_ACTIVITY)) 629 return IRQ_NONE; 630 631 i2c_dw_irq_handler_master(dev); 632 633 return IRQ_HANDLED; 634 } 635 636 static void i2c_dw_prepare_recovery(struct i2c_adapter *adap) 637 { 638 struct dw_i2c_dev *dev = i2c_get_adapdata(adap); 639 640 i2c_dw_disable(dev); 641 reset_control_assert(dev->rst); 642 i2c_dw_prepare_clk(dev, false); 643 } 644 645 static void i2c_dw_unprepare_recovery(struct i2c_adapter *adap) 646 { 647 struct dw_i2c_dev *dev = i2c_get_adapdata(adap); 648 649 i2c_dw_prepare_clk(dev, true); 650 reset_control_deassert(dev->rst); 651 i2c_dw_init_master(dev); 652 } 653 654 static int i2c_dw_init_recovery_info(struct dw_i2c_dev *dev) 655 { 656 struct i2c_bus_recovery_info *rinfo = &dev->rinfo; 657 struct i2c_adapter *adap = &dev->adapter; 658 struct gpio_desc *gpio; 659 int r; 660 661 gpio = devm_gpiod_get(dev->dev, "scl", GPIOD_OUT_HIGH); 662 if (IS_ERR(gpio)) { 663 r = PTR_ERR(gpio); 664 if (r == -ENOENT || r == -ENOSYS) 665 return 0; 666 return r; 667 } 668 rinfo->scl_gpiod = gpio; 669 670 gpio = devm_gpiod_get_optional(dev->dev, "sda", GPIOD_IN); 671 if (IS_ERR(gpio)) 672 return PTR_ERR(gpio); 673 rinfo->sda_gpiod = gpio; 674 675 rinfo->recover_bus = i2c_generic_scl_recovery; 676 rinfo->prepare_recovery = i2c_dw_prepare_recovery; 677 rinfo->unprepare_recovery = i2c_dw_unprepare_recovery; 678 adap->bus_recovery_info = rinfo; 679 680 dev_info(dev->dev, "running with gpio recovery mode! scl%s", 681 rinfo->sda_gpiod ? ",sda" : ""); 682 683 return 0; 684 } 685 686 int i2c_dw_probe(struct dw_i2c_dev *dev) 687 { 688 struct i2c_adapter *adap = &dev->adapter; 689 unsigned long irq_flags; 690 int ret; 691 692 init_completion(&dev->cmd_complete); 693 694 dev->init = i2c_dw_init_master; 695 dev->disable = i2c_dw_disable; 696 dev->disable_int = i2c_dw_disable_int; 697 698 ret = i2c_dw_set_reg_access(dev); 699 if (ret) 700 return ret; 701 702 ret = i2c_dw_set_timings_master(dev); 703 if (ret) 704 return ret; 705 706 ret = dev->init(dev); 707 if (ret) 708 return ret; 709 710 snprintf(adap->name, sizeof(adap->name), 711 "Synopsys DesignWare I2C adapter"); 712 adap->retries = 3; 713 adap->algo = &i2c_dw_algo; 714 adap->quirks = &i2c_dw_quirks; 715 adap->dev.parent = dev->dev; 716 i2c_set_adapdata(adap, dev); 717 718 if (dev->flags & ACCESS_NO_IRQ_SUSPEND) { 719 irq_flags = IRQF_NO_SUSPEND; 720 } else { 721 irq_flags = IRQF_SHARED | IRQF_COND_SUSPEND; 722 } 723 724 i2c_dw_disable_int(dev); 725 ret = devm_request_irq(dev->dev, dev->irq, i2c_dw_isr, irq_flags, 726 dev_name(dev->dev), dev); 727 if (ret) { 728 dev_err(dev->dev, "failure requesting irq %i: %d\n", 729 dev->irq, ret); 730 return ret; 731 } 732 733 ret = i2c_dw_init_recovery_info(dev); 734 if (ret) 735 return ret; 736 737 /* 738 * Increment PM usage count during adapter registration in order to 739 * avoid possible spurious runtime suspend when adapter device is 740 * registered to the device core and immediate resume in case bus has 741 * registered I2C slaves that do I2C transfers in their probe. 742 */ 743 pm_runtime_get_noresume(dev->dev); 744 ret = i2c_add_numbered_adapter(adap); 745 if (ret) 746 dev_err(dev->dev, "failure adding adapter: %d\n", ret); 747 pm_runtime_put_noidle(dev->dev); 748 749 return ret; 750 } 751 EXPORT_SYMBOL_GPL(i2c_dw_probe); 752 753 MODULE_DESCRIPTION("Synopsys DesignWare I2C bus master adapter"); 754 MODULE_LICENSE("GPL"); 755