xref: /openbmc/linux/drivers/i2c/busses/i2c-cadence.c (revision ee7da21a)
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * I2C bus driver for the Cadence I2C controller.
4  *
5  * Copyright (C) 2009 - 2014 Xilinx, Inc.
6  */
7 
8 #include <linux/clk.h>
9 #include <linux/delay.h>
10 #include <linux/i2c.h>
11 #include <linux/interrupt.h>
12 #include <linux/io.h>
13 #include <linux/module.h>
14 #include <linux/platform_device.h>
15 #include <linux/of.h>
16 #include <linux/pm_runtime.h>
17 
18 /* Register offsets for the I2C device. */
19 #define CDNS_I2C_CR_OFFSET		0x00 /* Control Register, RW */
20 #define CDNS_I2C_SR_OFFSET		0x04 /* Status Register, RO */
21 #define CDNS_I2C_ADDR_OFFSET		0x08 /* I2C Address Register, RW */
22 #define CDNS_I2C_DATA_OFFSET		0x0C /* I2C Data Register, RW */
23 #define CDNS_I2C_ISR_OFFSET		0x10 /* IRQ Status Register, RW */
24 #define CDNS_I2C_XFER_SIZE_OFFSET	0x14 /* Transfer Size Register, RW */
25 #define CDNS_I2C_TIME_OUT_OFFSET	0x1C /* Time Out Register, RW */
26 #define CDNS_I2C_IMR_OFFSET		0x20 /* IRQ Mask Register, RO */
27 #define CDNS_I2C_IER_OFFSET		0x24 /* IRQ Enable Register, WO */
28 #define CDNS_I2C_IDR_OFFSET		0x28 /* IRQ Disable Register, WO */
29 
30 /* Control Register Bit mask definitions */
31 #define CDNS_I2C_CR_HOLD		BIT(4) /* Hold Bus bit */
32 #define CDNS_I2C_CR_ACK_EN		BIT(3)
33 #define CDNS_I2C_CR_NEA			BIT(2)
34 #define CDNS_I2C_CR_MS			BIT(1)
35 /* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */
36 #define CDNS_I2C_CR_RW			BIT(0)
37 /* 1 = Auto init FIFO to zeroes */
38 #define CDNS_I2C_CR_CLR_FIFO		BIT(6)
39 #define CDNS_I2C_CR_DIVA_SHIFT		14
40 #define CDNS_I2C_CR_DIVA_MASK		(3 << CDNS_I2C_CR_DIVA_SHIFT)
41 #define CDNS_I2C_CR_DIVB_SHIFT		8
42 #define CDNS_I2C_CR_DIVB_MASK		(0x3f << CDNS_I2C_CR_DIVB_SHIFT)
43 
44 #define CDNS_I2C_CR_MASTER_EN_MASK	(CDNS_I2C_CR_NEA | \
45 					 CDNS_I2C_CR_ACK_EN | \
46 					 CDNS_I2C_CR_MS)
47 
48 #define CDNS_I2C_CR_SLAVE_EN_MASK	~CDNS_I2C_CR_MASTER_EN_MASK
49 
50 /* Status Register Bit mask definitions */
51 #define CDNS_I2C_SR_BA		BIT(8)
52 #define CDNS_I2C_SR_TXDV	BIT(6)
53 #define CDNS_I2C_SR_RXDV	BIT(5)
54 #define CDNS_I2C_SR_RXRW	BIT(3)
55 
56 /*
57  * I2C Address Register Bit mask definitions
58  * Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0]
59  * bits. A write access to this register always initiates a transfer if the I2C
60  * is in master mode.
61  */
62 #define CDNS_I2C_ADDR_MASK	0x000003FF /* I2C Address Mask */
63 
64 /*
65  * I2C Interrupt Registers Bit mask definitions
66  * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
67  * bit definitions.
68  */
69 #define CDNS_I2C_IXR_ARB_LOST		BIT(9)
70 #define CDNS_I2C_IXR_RX_UNF		BIT(7)
71 #define CDNS_I2C_IXR_TX_OVF		BIT(6)
72 #define CDNS_I2C_IXR_RX_OVF		BIT(5)
73 #define CDNS_I2C_IXR_SLV_RDY		BIT(4)
74 #define CDNS_I2C_IXR_TO			BIT(3)
75 #define CDNS_I2C_IXR_NACK		BIT(2)
76 #define CDNS_I2C_IXR_DATA		BIT(1)
77 #define CDNS_I2C_IXR_COMP		BIT(0)
78 
79 #define CDNS_I2C_IXR_ALL_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
80 					 CDNS_I2C_IXR_RX_UNF | \
81 					 CDNS_I2C_IXR_TX_OVF | \
82 					 CDNS_I2C_IXR_RX_OVF | \
83 					 CDNS_I2C_IXR_SLV_RDY | \
84 					 CDNS_I2C_IXR_TO | \
85 					 CDNS_I2C_IXR_NACK | \
86 					 CDNS_I2C_IXR_DATA | \
87 					 CDNS_I2C_IXR_COMP)
88 
89 #define CDNS_I2C_IXR_ERR_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
90 					 CDNS_I2C_IXR_RX_UNF | \
91 					 CDNS_I2C_IXR_TX_OVF | \
92 					 CDNS_I2C_IXR_RX_OVF | \
93 					 CDNS_I2C_IXR_NACK)
94 
95 #define CDNS_I2C_ENABLED_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
96 					 CDNS_I2C_IXR_RX_UNF | \
97 					 CDNS_I2C_IXR_TX_OVF | \
98 					 CDNS_I2C_IXR_RX_OVF | \
99 					 CDNS_I2C_IXR_NACK | \
100 					 CDNS_I2C_IXR_DATA | \
101 					 CDNS_I2C_IXR_COMP)
102 
103 #define CDNS_I2C_IXR_SLAVE_INTR_MASK	(CDNS_I2C_IXR_RX_UNF | \
104 					 CDNS_I2C_IXR_TX_OVF | \
105 					 CDNS_I2C_IXR_RX_OVF | \
106 					 CDNS_I2C_IXR_TO | \
107 					 CDNS_I2C_IXR_NACK | \
108 					 CDNS_I2C_IXR_DATA | \
109 					 CDNS_I2C_IXR_COMP)
110 
111 #define CDNS_I2C_TIMEOUT		msecs_to_jiffies(1000)
112 /* timeout for pm runtime autosuspend */
113 #define CNDS_I2C_PM_TIMEOUT		1000	/* ms */
114 
115 #define CDNS_I2C_FIFO_DEPTH		16
116 /* FIFO depth at which the DATA interrupt occurs */
117 #define CDNS_I2C_DATA_INTR_DEPTH	(CDNS_I2C_FIFO_DEPTH - 2)
118 #define CDNS_I2C_MAX_TRANSFER_SIZE	255
119 /* Transfer size in multiples of data interrupt depth */
120 #define CDNS_I2C_TRANSFER_SIZE	(CDNS_I2C_MAX_TRANSFER_SIZE - 3)
121 
122 #define DRIVER_NAME		"cdns-i2c"
123 
124 #define CDNS_I2C_DIVA_MAX	4
125 #define CDNS_I2C_DIVB_MAX	64
126 
127 #define CDNS_I2C_TIMEOUT_MAX	0xFF
128 
129 #define CDNS_I2C_BROKEN_HOLD_BIT	BIT(0)
130 
131 #define cdns_i2c_readreg(offset)       readl_relaxed(id->membase + offset)
132 #define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
133 
134 #if IS_ENABLED(CONFIG_I2C_SLAVE)
135 /**
136  * enum cdns_i2c_mode - I2C Controller current operating mode
137  *
138  * @CDNS_I2C_MODE_SLAVE:       I2C controller operating in slave mode
139  * @CDNS_I2C_MODE_MASTER:      I2C Controller operating in master mode
140  */
141 enum cdns_i2c_mode {
142 	CDNS_I2C_MODE_SLAVE,
143 	CDNS_I2C_MODE_MASTER,
144 };
145 
146 /**
147  * enum cdns_i2c_slave_state - Slave state when I2C is operating in slave mode
148  *
149  * @CDNS_I2C_SLAVE_STATE_IDLE: I2C slave idle
150  * @CDNS_I2C_SLAVE_STATE_SEND: I2C slave sending data to master
151  * @CDNS_I2C_SLAVE_STATE_RECV: I2C slave receiving data from master
152  */
153 enum cdns_i2c_slave_state {
154 	CDNS_I2C_SLAVE_STATE_IDLE,
155 	CDNS_I2C_SLAVE_STATE_SEND,
156 	CDNS_I2C_SLAVE_STATE_RECV,
157 };
158 #endif
159 
160 /**
161  * struct cdns_i2c - I2C device private data structure
162  *
163  * @dev:		Pointer to device structure
164  * @membase:		Base address of the I2C device
165  * @adap:		I2C adapter instance
166  * @p_msg:		Message pointer
167  * @err_status:		Error status in Interrupt Status Register
168  * @xfer_done:		Transfer complete status
169  * @p_send_buf:		Pointer to transmit buffer
170  * @p_recv_buf:		Pointer to receive buffer
171  * @send_count:		Number of bytes still expected to send
172  * @recv_count:		Number of bytes still expected to receive
173  * @curr_recv_count:	Number of bytes to be received in current transfer
174  * @irq:		IRQ number
175  * @input_clk:		Input clock to I2C controller
176  * @i2c_clk:		Maximum I2C clock speed
177  * @bus_hold_flag:	Flag used in repeated start for clearing HOLD bit
178  * @clk:		Pointer to struct clk
179  * @clk_rate_change_nb:	Notifier block for clock rate changes
180  * @quirks:		flag for broken hold bit usage in r1p10
181  * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register
182  * @slave:		Registered slave instance.
183  * @dev_mode:		I2C operating role(master/slave).
184  * @slave_state:	I2C Slave state(idle/read/write).
185  */
186 struct cdns_i2c {
187 	struct device		*dev;
188 	void __iomem *membase;
189 	struct i2c_adapter adap;
190 	struct i2c_msg *p_msg;
191 	int err_status;
192 	struct completion xfer_done;
193 	unsigned char *p_send_buf;
194 	unsigned char *p_recv_buf;
195 	unsigned int send_count;
196 	unsigned int recv_count;
197 	unsigned int curr_recv_count;
198 	int irq;
199 	unsigned long input_clk;
200 	unsigned int i2c_clk;
201 	unsigned int bus_hold_flag;
202 	struct clk *clk;
203 	struct notifier_block clk_rate_change_nb;
204 	u32 quirks;
205 #if IS_ENABLED(CONFIG_I2C_SLAVE)
206 	u16 ctrl_reg_diva_divb;
207 	struct i2c_client *slave;
208 	enum cdns_i2c_mode dev_mode;
209 	enum cdns_i2c_slave_state slave_state;
210 #endif
211 };
212 
213 struct cdns_platform_data {
214 	u32 quirks;
215 };
216 
217 #define to_cdns_i2c(_nb)	container_of(_nb, struct cdns_i2c, \
218 					     clk_rate_change_nb)
219 
220 /**
221  * cdns_i2c_clear_bus_hold - Clear bus hold bit
222  * @id:	Pointer to driver data struct
223  *
224  * Helper to clear the controller's bus hold bit.
225  */
226 static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id)
227 {
228 	u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
229 	if (reg & CDNS_I2C_CR_HOLD)
230 		cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET);
231 }
232 
233 static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround)
234 {
235 	return (hold_wrkaround &&
236 		(id->curr_recv_count == CDNS_I2C_FIFO_DEPTH + 1));
237 }
238 
239 #if IS_ENABLED(CONFIG_I2C_SLAVE)
240 static void cdns_i2c_set_mode(enum cdns_i2c_mode mode, struct cdns_i2c *id)
241 {
242 	/* Disable all interrupts */
243 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
244 
245 	/* Clear FIFO and transfer size */
246 	cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
247 
248 	/* Update device mode and state */
249 	id->dev_mode = mode;
250 	id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
251 
252 	switch (mode) {
253 	case CDNS_I2C_MODE_MASTER:
254 		/* Enable i2c master */
255 		cdns_i2c_writereg(id->ctrl_reg_diva_divb |
256 				  CDNS_I2C_CR_MASTER_EN_MASK,
257 				  CDNS_I2C_CR_OFFSET);
258 		/*
259 		 * This delay is needed to give the IP some time to switch to
260 		 * the master mode. With lower values(like 110 us) i2cdetect
261 		 * will not detect any slave and without this delay, the IP will
262 		 * trigger a timeout interrupt.
263 		 */
264 		usleep_range(115, 125);
265 		break;
266 	case CDNS_I2C_MODE_SLAVE:
267 		/* Enable i2c slave */
268 		cdns_i2c_writereg(id->ctrl_reg_diva_divb &
269 				  CDNS_I2C_CR_SLAVE_EN_MASK,
270 				  CDNS_I2C_CR_OFFSET);
271 
272 		/* Setting slave address */
273 		cdns_i2c_writereg(id->slave->addr & CDNS_I2C_ADDR_MASK,
274 				  CDNS_I2C_ADDR_OFFSET);
275 
276 		/* Enable slave send/receive interrupts */
277 		cdns_i2c_writereg(CDNS_I2C_IXR_SLAVE_INTR_MASK,
278 				  CDNS_I2C_IER_OFFSET);
279 		break;
280 	}
281 }
282 
283 static void cdns_i2c_slave_rcv_data(struct cdns_i2c *id)
284 {
285 	u8 bytes;
286 	unsigned char data;
287 
288 	/* Prepare backend for data reception */
289 	if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
290 		id->slave_state = CDNS_I2C_SLAVE_STATE_RECV;
291 		i2c_slave_event(id->slave, I2C_SLAVE_WRITE_REQUESTED, NULL);
292 	}
293 
294 	/* Fetch number of bytes to receive */
295 	bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
296 
297 	/* Read data and send to backend */
298 	while (bytes--) {
299 		data = cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
300 		i2c_slave_event(id->slave, I2C_SLAVE_WRITE_RECEIVED, &data);
301 	}
302 }
303 
304 static void cdns_i2c_slave_send_data(struct cdns_i2c *id)
305 {
306 	u8 data;
307 
308 	/* Prepare backend for data transmission */
309 	if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
310 		id->slave_state = CDNS_I2C_SLAVE_STATE_SEND;
311 		i2c_slave_event(id->slave, I2C_SLAVE_READ_REQUESTED, &data);
312 	} else {
313 		i2c_slave_event(id->slave, I2C_SLAVE_READ_PROCESSED, &data);
314 	}
315 
316 	/* Send data over bus */
317 	cdns_i2c_writereg(data, CDNS_I2C_DATA_OFFSET);
318 }
319 
320 /**
321  * cdns_i2c_slave_isr - Interrupt handler for the I2C device in slave role
322  * @ptr:       Pointer to I2C device private data
323  *
324  * This function handles the data interrupt and transfer complete interrupt of
325  * the I2C device in slave role.
326  *
327  * Return: IRQ_HANDLED always
328  */
329 static irqreturn_t cdns_i2c_slave_isr(void *ptr)
330 {
331 	struct cdns_i2c *id = ptr;
332 	unsigned int isr_status, i2c_status;
333 
334 	/* Fetch the interrupt status */
335 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
336 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
337 
338 	/* Ignore masked interrupts */
339 	isr_status &= ~cdns_i2c_readreg(CDNS_I2C_IMR_OFFSET);
340 
341 	/* Fetch transfer mode (send/receive) */
342 	i2c_status = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
343 
344 	/* Handle data send/receive */
345 	if (i2c_status & CDNS_I2C_SR_RXRW) {
346 		/* Send data to master */
347 		if (isr_status & CDNS_I2C_IXR_DATA)
348 			cdns_i2c_slave_send_data(id);
349 
350 		if (isr_status & CDNS_I2C_IXR_COMP) {
351 			id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
352 			i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
353 		}
354 	} else {
355 		/* Receive data from master */
356 		if (isr_status & CDNS_I2C_IXR_DATA)
357 			cdns_i2c_slave_rcv_data(id);
358 
359 		if (isr_status & CDNS_I2C_IXR_COMP) {
360 			cdns_i2c_slave_rcv_data(id);
361 			id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
362 			i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
363 		}
364 	}
365 
366 	/* Master indicated xfer stop or fifo underflow/overflow */
367 	if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_RX_OVF |
368 			  CDNS_I2C_IXR_RX_UNF | CDNS_I2C_IXR_TX_OVF)) {
369 		id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
370 		i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
371 		cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
372 	}
373 
374 	return IRQ_HANDLED;
375 }
376 #endif
377 
378 /**
379  * cdns_i2c_master_isr - Interrupt handler for the I2C device in master role
380  * @ptr:       Pointer to I2C device private data
381  *
382  * This function handles the data interrupt, transfer complete interrupt and
383  * the error interrupts of the I2C device in master role.
384  *
385  * Return: IRQ_HANDLED always
386  */
387 static irqreturn_t cdns_i2c_master_isr(void *ptr)
388 {
389 	unsigned int isr_status, avail_bytes, updatetx;
390 	unsigned int bytes_to_send;
391 	bool hold_quirk;
392 	struct cdns_i2c *id = ptr;
393 	/* Signal completion only after everything is updated */
394 	int done_flag = 0;
395 	irqreturn_t status = IRQ_NONE;
396 
397 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
398 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
399 	id->err_status = 0;
400 
401 	/* Handling nack and arbitration lost interrupt */
402 	if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) {
403 		done_flag = 1;
404 		status = IRQ_HANDLED;
405 	}
406 
407 	/*
408 	 * Check if transfer size register needs to be updated again for a
409 	 * large data receive operation.
410 	 */
411 	updatetx = 0;
412 	if (id->recv_count > id->curr_recv_count)
413 		updatetx = 1;
414 
415 	hold_quirk = (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) && updatetx;
416 
417 	/* When receiving, handle data interrupt and completion interrupt */
418 	if (id->p_recv_buf &&
419 	    ((isr_status & CDNS_I2C_IXR_COMP) ||
420 	     (isr_status & CDNS_I2C_IXR_DATA))) {
421 		/* Read data if receive data valid is set */
422 		while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
423 		       CDNS_I2C_SR_RXDV) {
424 			if (id->recv_count > 0) {
425 				*(id->p_recv_buf)++ =
426 					cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
427 				id->recv_count--;
428 				id->curr_recv_count--;
429 
430 				/*
431 				 * Clear hold bit that was set for FIFO control
432 				 * if RX data left is less than or equal to
433 				 * FIFO DEPTH unless repeated start is selected
434 				 */
435 				if (id->recv_count <= CDNS_I2C_FIFO_DEPTH &&
436 				    !id->bus_hold_flag)
437 					cdns_i2c_clear_bus_hold(id);
438 
439 			} else {
440 				dev_err(id->adap.dev.parent,
441 					"xfer_size reg rollover. xfer aborted!\n");
442 				id->err_status |= CDNS_I2C_IXR_TO;
443 				break;
444 			}
445 
446 			if (cdns_is_holdquirk(id, hold_quirk))
447 				break;
448 		}
449 
450 		/*
451 		 * The controller sends NACK to the slave when transfer size
452 		 * register reaches zero without considering the HOLD bit.
453 		 * This workaround is implemented for large data transfers to
454 		 * maintain transfer size non-zero while performing a large
455 		 * receive operation.
456 		 */
457 		if (cdns_is_holdquirk(id, hold_quirk)) {
458 			/* wait while fifo is full */
459 			while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) !=
460 			       (id->curr_recv_count - CDNS_I2C_FIFO_DEPTH))
461 				;
462 
463 			/*
464 			 * Check number of bytes to be received against maximum
465 			 * transfer size and update register accordingly.
466 			 */
467 			if (((int)(id->recv_count) - CDNS_I2C_FIFO_DEPTH) >
468 			    CDNS_I2C_TRANSFER_SIZE) {
469 				cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
470 						  CDNS_I2C_XFER_SIZE_OFFSET);
471 				id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE +
472 						      CDNS_I2C_FIFO_DEPTH;
473 			} else {
474 				cdns_i2c_writereg(id->recv_count -
475 						  CDNS_I2C_FIFO_DEPTH,
476 						  CDNS_I2C_XFER_SIZE_OFFSET);
477 				id->curr_recv_count = id->recv_count;
478 			}
479 		} else if (id->recv_count && !hold_quirk &&
480 						!id->curr_recv_count) {
481 
482 			/* Set the slave address in address register*/
483 			cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
484 						CDNS_I2C_ADDR_OFFSET);
485 
486 			if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
487 				cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
488 						CDNS_I2C_XFER_SIZE_OFFSET);
489 				id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
490 			} else {
491 				cdns_i2c_writereg(id->recv_count,
492 						CDNS_I2C_XFER_SIZE_OFFSET);
493 				id->curr_recv_count = id->recv_count;
494 			}
495 		}
496 
497 		/* Clear hold (if not repeated start) and signal completion */
498 		if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) {
499 			if (!id->bus_hold_flag)
500 				cdns_i2c_clear_bus_hold(id);
501 			done_flag = 1;
502 		}
503 
504 		status = IRQ_HANDLED;
505 	}
506 
507 	/* When sending, handle transfer complete interrupt */
508 	if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) {
509 		/*
510 		 * If there is more data to be sent, calculate the
511 		 * space available in FIFO and fill with that many bytes.
512 		 */
513 		if (id->send_count) {
514 			avail_bytes = CDNS_I2C_FIFO_DEPTH -
515 			    cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
516 			if (id->send_count > avail_bytes)
517 				bytes_to_send = avail_bytes;
518 			else
519 				bytes_to_send = id->send_count;
520 
521 			while (bytes_to_send--) {
522 				cdns_i2c_writereg(
523 					(*(id->p_send_buf)++),
524 					 CDNS_I2C_DATA_OFFSET);
525 				id->send_count--;
526 			}
527 		} else {
528 			/*
529 			 * Signal the completion of transaction and
530 			 * clear the hold bus bit if there are no
531 			 * further messages to be processed.
532 			 */
533 			done_flag = 1;
534 		}
535 		if (!id->send_count && !id->bus_hold_flag)
536 			cdns_i2c_clear_bus_hold(id);
537 
538 		status = IRQ_HANDLED;
539 	}
540 
541 	/* Update the status for errors */
542 	id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK;
543 	if (id->err_status)
544 		status = IRQ_HANDLED;
545 
546 	if (done_flag)
547 		complete(&id->xfer_done);
548 
549 	return status;
550 }
551 
552 /**
553  * cdns_i2c_isr - Interrupt handler for the I2C device
554  * @irq:	irq number for the I2C device
555  * @ptr:	void pointer to cdns_i2c structure
556  *
557  * This function passes the control to slave/master based on current role of
558  * i2c controller.
559  *
560  * Return: IRQ_HANDLED always
561  */
562 static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
563 {
564 #if IS_ENABLED(CONFIG_I2C_SLAVE)
565 	struct cdns_i2c *id = ptr;
566 
567 	if (id->dev_mode == CDNS_I2C_MODE_SLAVE)
568 		return cdns_i2c_slave_isr(ptr);
569 #endif
570 	return cdns_i2c_master_isr(ptr);
571 }
572 
573 /**
574  * cdns_i2c_mrecv - Prepare and start a master receive operation
575  * @id:		pointer to the i2c device structure
576  */
577 static void cdns_i2c_mrecv(struct cdns_i2c *id)
578 {
579 	unsigned int ctrl_reg;
580 	unsigned int isr_status;
581 	unsigned long flags;
582 	bool hold_clear = false;
583 	bool irq_save = false;
584 
585 	u32 addr;
586 
587 	id->p_recv_buf = id->p_msg->buf;
588 	id->recv_count = id->p_msg->len;
589 
590 	/* Put the controller in master receive mode and clear the FIFO */
591 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
592 	ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO;
593 
594 	if (id->p_msg->flags & I2C_M_RECV_LEN)
595 		id->recv_count = I2C_SMBUS_BLOCK_MAX + 1;
596 
597 	id->curr_recv_count = id->recv_count;
598 
599 	/*
600 	 * Check for the message size against FIFO depth and set the
601 	 * 'hold bus' bit if it is greater than FIFO depth.
602 	 */
603 	if (id->recv_count > CDNS_I2C_FIFO_DEPTH)
604 		ctrl_reg |= CDNS_I2C_CR_HOLD;
605 
606 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
607 
608 	/* Clear the interrupts in interrupt status register */
609 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
610 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
611 
612 	/*
613 	 * The no. of bytes to receive is checked against the limit of
614 	 * max transfer size. Set transfer size register with no of bytes
615 	 * receive if it is less than transfer size and transfer size if
616 	 * it is more. Enable the interrupts.
617 	 */
618 	if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
619 		cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
620 				  CDNS_I2C_XFER_SIZE_OFFSET);
621 		id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
622 	} else {
623 		cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET);
624 	}
625 
626 	/* Determine hold_clear based on number of bytes to receive and hold flag */
627 	if (!id->bus_hold_flag &&
628 	    ((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
629 	    (id->recv_count <= CDNS_I2C_FIFO_DEPTH)) {
630 		if (cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & CDNS_I2C_CR_HOLD) {
631 			hold_clear = true;
632 			if (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT)
633 				irq_save = true;
634 		}
635 	}
636 
637 	addr = id->p_msg->addr;
638 	addr &= CDNS_I2C_ADDR_MASK;
639 
640 	if (hold_clear) {
641 		ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & ~CDNS_I2C_CR_HOLD;
642 		/*
643 		 * In case of Xilinx Zynq SOC, clear the HOLD bit before transfer size
644 		 * register reaches '0'. This is an IP bug which causes transfer size
645 		 * register overflow to 0xFF. To satisfy this timing requirement,
646 		 * disable the interrupts on current processor core between register
647 		 * writes to slave address register and control register.
648 		 */
649 		if (irq_save)
650 			local_irq_save(flags);
651 
652 		cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
653 		cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
654 		/* Read it back to avoid bufferring and make sure write happens */
655 		cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
656 
657 		if (irq_save)
658 			local_irq_restore(flags);
659 	} else {
660 		cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
661 	}
662 
663 	cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
664 }
665 
666 /**
667  * cdns_i2c_msend - Prepare and start a master send operation
668  * @id:		pointer to the i2c device
669  */
670 static void cdns_i2c_msend(struct cdns_i2c *id)
671 {
672 	unsigned int avail_bytes;
673 	unsigned int bytes_to_send;
674 	unsigned int ctrl_reg;
675 	unsigned int isr_status;
676 
677 	id->p_recv_buf = NULL;
678 	id->p_send_buf = id->p_msg->buf;
679 	id->send_count = id->p_msg->len;
680 
681 	/* Set the controller in Master transmit mode and clear the FIFO. */
682 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
683 	ctrl_reg &= ~CDNS_I2C_CR_RW;
684 	ctrl_reg |= CDNS_I2C_CR_CLR_FIFO;
685 
686 	/*
687 	 * Check for the message size against FIFO depth and set the
688 	 * 'hold bus' bit if it is greater than FIFO depth.
689 	 */
690 	if (id->send_count > CDNS_I2C_FIFO_DEPTH)
691 		ctrl_reg |= CDNS_I2C_CR_HOLD;
692 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
693 
694 	/* Clear the interrupts in interrupt status register. */
695 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
696 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
697 
698 	/*
699 	 * Calculate the space available in FIFO. Check the message length
700 	 * against the space available, and fill the FIFO accordingly.
701 	 * Enable the interrupts.
702 	 */
703 	avail_bytes = CDNS_I2C_FIFO_DEPTH -
704 				cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
705 
706 	if (id->send_count > avail_bytes)
707 		bytes_to_send = avail_bytes;
708 	else
709 		bytes_to_send = id->send_count;
710 
711 	while (bytes_to_send--) {
712 		cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET);
713 		id->send_count--;
714 	}
715 
716 	/*
717 	 * Clear the bus hold flag if there is no more data
718 	 * and if it is the last message.
719 	 */
720 	if (!id->bus_hold_flag && !id->send_count)
721 		cdns_i2c_clear_bus_hold(id);
722 	/* Set the slave address in address register - triggers operation. */
723 	cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
724 						CDNS_I2C_ADDR_OFFSET);
725 
726 	cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
727 }
728 
729 /**
730  * cdns_i2c_master_reset - Reset the interface
731  * @adap:	pointer to the i2c adapter driver instance
732  *
733  * This function cleanup the fifos, clear the hold bit and status
734  * and disable the interrupts.
735  */
736 static void cdns_i2c_master_reset(struct i2c_adapter *adap)
737 {
738 	struct cdns_i2c *id = adap->algo_data;
739 	u32 regval;
740 
741 	/* Disable the interrupts */
742 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
743 	/* Clear the hold bit and fifos */
744 	regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
745 	regval &= ~CDNS_I2C_CR_HOLD;
746 	regval |= CDNS_I2C_CR_CLR_FIFO;
747 	cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET);
748 	/* Update the transfercount register to zero */
749 	cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET);
750 	/* Clear the interrupt status register */
751 	regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
752 	cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET);
753 	/* Clear the status register */
754 	regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
755 	cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET);
756 }
757 
758 static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg,
759 		struct i2c_adapter *adap)
760 {
761 	unsigned long time_left;
762 	u32 reg;
763 
764 	id->p_msg = msg;
765 	id->err_status = 0;
766 	reinit_completion(&id->xfer_done);
767 
768 	/* Check for the TEN Bit mode on each msg */
769 	reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
770 	if (msg->flags & I2C_M_TEN) {
771 		if (reg & CDNS_I2C_CR_NEA)
772 			cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA,
773 					CDNS_I2C_CR_OFFSET);
774 	} else {
775 		if (!(reg & CDNS_I2C_CR_NEA))
776 			cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA,
777 					CDNS_I2C_CR_OFFSET);
778 	}
779 
780 	/* Check for the R/W flag on each msg */
781 	if (msg->flags & I2C_M_RD)
782 		cdns_i2c_mrecv(id);
783 	else
784 		cdns_i2c_msend(id);
785 
786 	/* Wait for the signal of completion */
787 	time_left = wait_for_completion_timeout(&id->xfer_done, adap->timeout);
788 	if (time_left == 0) {
789 		cdns_i2c_master_reset(adap);
790 		dev_err(id->adap.dev.parent,
791 				"timeout waiting on completion\n");
792 		return -ETIMEDOUT;
793 	}
794 
795 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK,
796 			  CDNS_I2C_IDR_OFFSET);
797 
798 	/* If it is bus arbitration error, try again */
799 	if (id->err_status & CDNS_I2C_IXR_ARB_LOST)
800 		return -EAGAIN;
801 
802 	return 0;
803 }
804 
805 /**
806  * cdns_i2c_master_xfer - The main i2c transfer function
807  * @adap:	pointer to the i2c adapter driver instance
808  * @msgs:	pointer to the i2c message structure
809  * @num:	the number of messages to transfer
810  *
811  * Initiates the send/recv activity based on the transfer message received.
812  *
813  * Return: number of msgs processed on success, negative error otherwise
814  */
815 static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
816 				int num)
817 {
818 	int ret, count;
819 	u32 reg;
820 	struct cdns_i2c *id = adap->algo_data;
821 	bool hold_quirk;
822 #if IS_ENABLED(CONFIG_I2C_SLAVE)
823 	bool change_role = false;
824 #endif
825 
826 	ret = pm_runtime_resume_and_get(id->dev);
827 	if (ret < 0)
828 		return ret;
829 
830 #if IS_ENABLED(CONFIG_I2C_SLAVE)
831 	/* Check i2c operating mode and switch if possible */
832 	if (id->dev_mode == CDNS_I2C_MODE_SLAVE) {
833 		if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE)
834 			return -EAGAIN;
835 
836 		/* Set mode to master */
837 		cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
838 
839 		/* Mark flag to change role once xfer is completed */
840 		change_role = true;
841 	}
842 #endif
843 
844 	/* Check if the bus is free */
845 	if (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & CDNS_I2C_SR_BA) {
846 		ret = -EAGAIN;
847 		goto out;
848 	}
849 
850 	hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT);
851 	/*
852 	 * Set the flag to one when multiple messages are to be
853 	 * processed with a repeated start.
854 	 */
855 	if (num > 1) {
856 		/*
857 		 * This controller does not give completion interrupt after a
858 		 * master receive message if HOLD bit is set (repeated start),
859 		 * resulting in SW timeout. Hence, if a receive message is
860 		 * followed by any other message, an error is returned
861 		 * indicating that this sequence is not supported.
862 		 */
863 		for (count = 0; (count < num - 1 && hold_quirk); count++) {
864 			if (msgs[count].flags & I2C_M_RD) {
865 				dev_warn(adap->dev.parent,
866 					 "Can't do repeated start after a receive message\n");
867 				ret = -EOPNOTSUPP;
868 				goto out;
869 			}
870 		}
871 		id->bus_hold_flag = 1;
872 		reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
873 		reg |= CDNS_I2C_CR_HOLD;
874 		cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET);
875 	} else {
876 		id->bus_hold_flag = 0;
877 	}
878 
879 	/* Process the msg one by one */
880 	for (count = 0; count < num; count++, msgs++) {
881 		if (count == (num - 1))
882 			id->bus_hold_flag = 0;
883 
884 		ret = cdns_i2c_process_msg(id, msgs, adap);
885 		if (ret)
886 			goto out;
887 
888 		/* Report the other error interrupts to application */
889 		if (id->err_status) {
890 			cdns_i2c_master_reset(adap);
891 
892 			if (id->err_status & CDNS_I2C_IXR_NACK) {
893 				ret = -ENXIO;
894 				goto out;
895 			}
896 			ret = -EIO;
897 			goto out;
898 		}
899 	}
900 
901 	ret = num;
902 
903 out:
904 
905 #if IS_ENABLED(CONFIG_I2C_SLAVE)
906 	/* Switch i2c mode to slave */
907 	if (change_role)
908 		cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
909 #endif
910 
911 	pm_runtime_mark_last_busy(id->dev);
912 	pm_runtime_put_autosuspend(id->dev);
913 	return ret;
914 }
915 
916 /**
917  * cdns_i2c_func - Returns the supported features of the I2C driver
918  * @adap:	pointer to the i2c adapter structure
919  *
920  * Return: 32 bit value, each bit corresponding to a feature
921  */
922 static u32 cdns_i2c_func(struct i2c_adapter *adap)
923 {
924 	u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR |
925 			(I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
926 			I2C_FUNC_SMBUS_BLOCK_DATA;
927 
928 #if IS_ENABLED(CONFIG_I2C_SLAVE)
929 	func |= I2C_FUNC_SLAVE;
930 #endif
931 
932 	return func;
933 }
934 
935 #if IS_ENABLED(CONFIG_I2C_SLAVE)
936 static int cdns_reg_slave(struct i2c_client *slave)
937 {
938 	int ret;
939 	struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
940 									adap);
941 
942 	if (id->slave)
943 		return -EBUSY;
944 
945 	if (slave->flags & I2C_CLIENT_TEN)
946 		return -EAFNOSUPPORT;
947 
948 	ret = pm_runtime_resume_and_get(id->dev);
949 	if (ret < 0)
950 		return ret;
951 
952 	/* Store slave information */
953 	id->slave = slave;
954 
955 	/* Enable I2C slave */
956 	cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
957 
958 	return 0;
959 }
960 
961 static int cdns_unreg_slave(struct i2c_client *slave)
962 {
963 	struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
964 									adap);
965 
966 	pm_runtime_put(id->dev);
967 
968 	/* Remove slave information */
969 	id->slave = NULL;
970 
971 	/* Enable I2C master */
972 	cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
973 
974 	return 0;
975 }
976 #endif
977 
978 static const struct i2c_algorithm cdns_i2c_algo = {
979 	.master_xfer	= cdns_i2c_master_xfer,
980 	.functionality	= cdns_i2c_func,
981 #if IS_ENABLED(CONFIG_I2C_SLAVE)
982 	.reg_slave	= cdns_reg_slave,
983 	.unreg_slave	= cdns_unreg_slave,
984 #endif
985 };
986 
987 /**
988  * cdns_i2c_calc_divs - Calculate clock dividers
989  * @f:		I2C clock frequency
990  * @input_clk:	Input clock frequency
991  * @a:		First divider (return value)
992  * @b:		Second divider (return value)
993  *
994  * f is used as input and output variable. As input it is used as target I2C
995  * frequency. On function exit f holds the actually resulting I2C frequency.
996  *
997  * Return: 0 on success, negative errno otherwise.
998  */
999 static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk,
1000 		unsigned int *a, unsigned int *b)
1001 {
1002 	unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp;
1003 	unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0;
1004 	unsigned int last_error, current_error;
1005 
1006 	/* calculate (divisor_a+1) x (divisor_b+1) */
1007 	temp = input_clk / (22 * fscl);
1008 
1009 	/*
1010 	 * If the calculated value is negative or 0, the fscl input is out of
1011 	 * range. Return error.
1012 	 */
1013 	if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX)))
1014 		return -EINVAL;
1015 
1016 	last_error = -1;
1017 	for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) {
1018 		div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1));
1019 
1020 		if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX))
1021 			continue;
1022 		div_b--;
1023 
1024 		actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1));
1025 
1026 		if (actual_fscl > fscl)
1027 			continue;
1028 
1029 		current_error = ((actual_fscl > fscl) ? (actual_fscl - fscl) :
1030 							(fscl - actual_fscl));
1031 
1032 		if (last_error > current_error) {
1033 			calc_div_a = div_a;
1034 			calc_div_b = div_b;
1035 			best_fscl = actual_fscl;
1036 			last_error = current_error;
1037 		}
1038 	}
1039 
1040 	*a = calc_div_a;
1041 	*b = calc_div_b;
1042 	*f = best_fscl;
1043 
1044 	return 0;
1045 }
1046 
1047 /**
1048  * cdns_i2c_setclk - This function sets the serial clock rate for the I2C device
1049  * @clk_in:	I2C clock input frequency in Hz
1050  * @id:		Pointer to the I2C device structure
1051  *
1052  * The device must be idle rather than busy transferring data before setting
1053  * these device options.
1054  * The data rate is set by values in the control register.
1055  * The formula for determining the correct register values is
1056  *	Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1))
1057  * See the hardware data sheet for a full explanation of setting the serial
1058  * clock rate. The clock can not be faster than the input clock divide by 22.
1059  * The two most common clock rates are 100KHz and 400KHz.
1060  *
1061  * Return: 0 on success, negative error otherwise
1062  */
1063 static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id)
1064 {
1065 	unsigned int div_a, div_b;
1066 	unsigned int ctrl_reg;
1067 	int ret = 0;
1068 	unsigned long fscl = id->i2c_clk;
1069 
1070 	ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b);
1071 	if (ret)
1072 		return ret;
1073 
1074 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
1075 	ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK);
1076 	ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) |
1077 			(div_b << CDNS_I2C_CR_DIVB_SHIFT));
1078 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
1079 #if IS_ENABLED(CONFIG_I2C_SLAVE)
1080 	id->ctrl_reg_diva_divb = ctrl_reg & (CDNS_I2C_CR_DIVA_MASK |
1081 				 CDNS_I2C_CR_DIVB_MASK);
1082 #endif
1083 	return 0;
1084 }
1085 
1086 /**
1087  * cdns_i2c_clk_notifier_cb - Clock rate change callback
1088  * @nb:		Pointer to notifier block
1089  * @event:	Notification reason
1090  * @data:	Pointer to notification data object
1091  *
1092  * This function is called when the cdns_i2c input clock frequency changes.
1093  * The callback checks whether a valid bus frequency can be generated after the
1094  * change. If so, the change is acknowledged, otherwise the change is aborted.
1095  * New dividers are written to the HW in the pre- or post change notification
1096  * depending on the scaling direction.
1097  *
1098  * Return:	NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
1099  *		to acknowledge the change, NOTIFY_DONE if the notification is
1100  *		considered irrelevant.
1101  */
1102 static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
1103 		event, void *data)
1104 {
1105 	struct clk_notifier_data *ndata = data;
1106 	struct cdns_i2c *id = to_cdns_i2c(nb);
1107 
1108 	if (pm_runtime_suspended(id->dev))
1109 		return NOTIFY_OK;
1110 
1111 	switch (event) {
1112 	case PRE_RATE_CHANGE:
1113 	{
1114 		unsigned long input_clk = ndata->new_rate;
1115 		unsigned long fscl = id->i2c_clk;
1116 		unsigned int div_a, div_b;
1117 		int ret;
1118 
1119 		ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b);
1120 		if (ret) {
1121 			dev_warn(id->adap.dev.parent,
1122 					"clock rate change rejected\n");
1123 			return NOTIFY_STOP;
1124 		}
1125 
1126 		/* scale up */
1127 		if (ndata->new_rate > ndata->old_rate)
1128 			cdns_i2c_setclk(ndata->new_rate, id);
1129 
1130 		return NOTIFY_OK;
1131 	}
1132 	case POST_RATE_CHANGE:
1133 		id->input_clk = ndata->new_rate;
1134 		/* scale down */
1135 		if (ndata->new_rate < ndata->old_rate)
1136 			cdns_i2c_setclk(ndata->new_rate, id);
1137 		return NOTIFY_OK;
1138 	case ABORT_RATE_CHANGE:
1139 		/* scale up */
1140 		if (ndata->new_rate > ndata->old_rate)
1141 			cdns_i2c_setclk(ndata->old_rate, id);
1142 		return NOTIFY_OK;
1143 	default:
1144 		return NOTIFY_DONE;
1145 	}
1146 }
1147 
1148 /**
1149  * cdns_i2c_runtime_suspend -  Runtime suspend method for the driver
1150  * @dev:	Address of the platform_device structure
1151  *
1152  * Put the driver into low power mode.
1153  *
1154  * Return: 0 always
1155  */
1156 static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev)
1157 {
1158 	struct cdns_i2c *xi2c = dev_get_drvdata(dev);
1159 
1160 	clk_disable(xi2c->clk);
1161 
1162 	return 0;
1163 }
1164 
1165 /**
1166  * cdns_i2c_runtime_resume - Runtime resume
1167  * @dev:	Address of the platform_device structure
1168  *
1169  * Runtime resume callback.
1170  *
1171  * Return: 0 on success and error value on error
1172  */
1173 static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev)
1174 {
1175 	struct cdns_i2c *xi2c = dev_get_drvdata(dev);
1176 	int ret;
1177 
1178 	ret = clk_enable(xi2c->clk);
1179 	if (ret) {
1180 		dev_err(dev, "Cannot enable clock.\n");
1181 		return ret;
1182 	}
1183 
1184 	return 0;
1185 }
1186 
1187 static const struct dev_pm_ops cdns_i2c_dev_pm_ops = {
1188 	SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend,
1189 			   cdns_i2c_runtime_resume, NULL)
1190 };
1191 
1192 static const struct cdns_platform_data r1p10_i2c_def = {
1193 	.quirks = CDNS_I2C_BROKEN_HOLD_BIT,
1194 };
1195 
1196 static const struct of_device_id cdns_i2c_of_match[] = {
1197 	{ .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def },
1198 	{ .compatible = "cdns,i2c-r1p14",},
1199 	{ /* end of table */ }
1200 };
1201 MODULE_DEVICE_TABLE(of, cdns_i2c_of_match);
1202 
1203 /**
1204  * cdns_i2c_probe - Platform registration call
1205  * @pdev:	Handle to the platform device structure
1206  *
1207  * This function does all the memory allocation and registration for the i2c
1208  * device. User can modify the address mode to 10 bit address mode using the
1209  * ioctl call with option I2C_TENBIT.
1210  *
1211  * Return: 0 on success, negative error otherwise
1212  */
1213 static int cdns_i2c_probe(struct platform_device *pdev)
1214 {
1215 	struct resource *r_mem;
1216 	struct cdns_i2c *id;
1217 	int ret;
1218 	const struct of_device_id *match;
1219 
1220 	id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL);
1221 	if (!id)
1222 		return -ENOMEM;
1223 
1224 	id->dev = &pdev->dev;
1225 	platform_set_drvdata(pdev, id);
1226 
1227 	match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node);
1228 	if (match && match->data) {
1229 		const struct cdns_platform_data *data = match->data;
1230 		id->quirks = data->quirks;
1231 	}
1232 
1233 	id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem);
1234 	if (IS_ERR(id->membase))
1235 		return PTR_ERR(id->membase);
1236 
1237 	ret = platform_get_irq(pdev, 0);
1238 	if (ret < 0)
1239 		return ret;
1240 	id->irq = ret;
1241 
1242 	id->adap.owner = THIS_MODULE;
1243 	id->adap.dev.of_node = pdev->dev.of_node;
1244 	id->adap.algo = &cdns_i2c_algo;
1245 	id->adap.timeout = CDNS_I2C_TIMEOUT;
1246 	id->adap.retries = 3;		/* Default retry value. */
1247 	id->adap.algo_data = id;
1248 	id->adap.dev.parent = &pdev->dev;
1249 	init_completion(&id->xfer_done);
1250 	snprintf(id->adap.name, sizeof(id->adap.name),
1251 		 "Cadence I2C at %08lx", (unsigned long)r_mem->start);
1252 
1253 	id->clk = devm_clk_get(&pdev->dev, NULL);
1254 	if (IS_ERR(id->clk))
1255 		return dev_err_probe(&pdev->dev, PTR_ERR(id->clk),
1256 				     "input clock not found.\n");
1257 
1258 	ret = clk_prepare_enable(id->clk);
1259 	if (ret)
1260 		dev_err(&pdev->dev, "Unable to enable clock.\n");
1261 
1262 	pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT);
1263 	pm_runtime_use_autosuspend(id->dev);
1264 	pm_runtime_set_active(id->dev);
1265 	pm_runtime_enable(id->dev);
1266 
1267 	id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb;
1268 	if (clk_notifier_register(id->clk, &id->clk_rate_change_nb))
1269 		dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
1270 	id->input_clk = clk_get_rate(id->clk);
1271 
1272 	ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
1273 			&id->i2c_clk);
1274 	if (ret || (id->i2c_clk > I2C_MAX_FAST_MODE_FREQ))
1275 		id->i2c_clk = I2C_MAX_STANDARD_MODE_FREQ;
1276 
1277 #if IS_ENABLED(CONFIG_I2C_SLAVE)
1278 	/* Set initial mode to master */
1279 	id->dev_mode = CDNS_I2C_MODE_MASTER;
1280 	id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
1281 #endif
1282 	cdns_i2c_writereg(CDNS_I2C_CR_MASTER_EN_MASK, CDNS_I2C_CR_OFFSET);
1283 
1284 	ret = cdns_i2c_setclk(id->input_clk, id);
1285 	if (ret) {
1286 		dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk);
1287 		ret = -EINVAL;
1288 		goto err_clk_dis;
1289 	}
1290 
1291 	ret = devm_request_irq(&pdev->dev, id->irq, cdns_i2c_isr, 0,
1292 				 DRIVER_NAME, id);
1293 	if (ret) {
1294 		dev_err(&pdev->dev, "cannot get irq %d\n", id->irq);
1295 		goto err_clk_dis;
1296 	}
1297 
1298 	/*
1299 	 * Cadence I2C controller has a bug wherein it generates
1300 	 * invalid read transaction after HW timeout in master receiver mode.
1301 	 * HW timeout is not used by this driver and the interrupt is disabled.
1302 	 * But the feature itself cannot be disabled. Hence maximum value
1303 	 * is written to this register to reduce the chances of error.
1304 	 */
1305 	cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET);
1306 
1307 	ret = i2c_add_adapter(&id->adap);
1308 	if (ret < 0)
1309 		goto err_clk_dis;
1310 
1311 	dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n",
1312 		 id->i2c_clk / 1000, (unsigned long)r_mem->start, id->irq);
1313 
1314 	return 0;
1315 
1316 err_clk_dis:
1317 	clk_disable_unprepare(id->clk);
1318 	pm_runtime_disable(&pdev->dev);
1319 	pm_runtime_set_suspended(&pdev->dev);
1320 	return ret;
1321 }
1322 
1323 /**
1324  * cdns_i2c_remove - Unregister the device after releasing the resources
1325  * @pdev:	Handle to the platform device structure
1326  *
1327  * This function frees all the resources allocated to the device.
1328  *
1329  * Return: 0 always
1330  */
1331 static int cdns_i2c_remove(struct platform_device *pdev)
1332 {
1333 	struct cdns_i2c *id = platform_get_drvdata(pdev);
1334 
1335 	pm_runtime_disable(&pdev->dev);
1336 	pm_runtime_set_suspended(&pdev->dev);
1337 	pm_runtime_dont_use_autosuspend(&pdev->dev);
1338 
1339 	i2c_del_adapter(&id->adap);
1340 	clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
1341 	clk_disable_unprepare(id->clk);
1342 
1343 	return 0;
1344 }
1345 
1346 static struct platform_driver cdns_i2c_drv = {
1347 	.driver = {
1348 		.name  = DRIVER_NAME,
1349 		.of_match_table = cdns_i2c_of_match,
1350 		.pm = &cdns_i2c_dev_pm_ops,
1351 	},
1352 	.probe  = cdns_i2c_probe,
1353 	.remove = cdns_i2c_remove,
1354 };
1355 
1356 module_platform_driver(cdns_i2c_drv);
1357 
1358 MODULE_AUTHOR("Xilinx Inc.");
1359 MODULE_DESCRIPTION("Cadence I2C bus driver");
1360 MODULE_LICENSE("GPL");
1361