1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * I2C bus driver for the Cadence I2C controller. 4 * 5 * Copyright (C) 2009 - 2014 Xilinx, Inc. 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/delay.h> 10 #include <linux/i2c.h> 11 #include <linux/interrupt.h> 12 #include <linux/io.h> 13 #include <linux/iopoll.h> 14 #include <linux/module.h> 15 #include <linux/platform_device.h> 16 #include <linux/of.h> 17 #include <linux/pm_runtime.h> 18 #include <linux/pinctrl/consumer.h> 19 #include <linux/reset.h> 20 21 /* Register offsets for the I2C device. */ 22 #define CDNS_I2C_CR_OFFSET 0x00 /* Control Register, RW */ 23 #define CDNS_I2C_SR_OFFSET 0x04 /* Status Register, RO */ 24 #define CDNS_I2C_ADDR_OFFSET 0x08 /* I2C Address Register, RW */ 25 #define CDNS_I2C_DATA_OFFSET 0x0C /* I2C Data Register, RW */ 26 #define CDNS_I2C_ISR_OFFSET 0x10 /* IRQ Status Register, RW */ 27 #define CDNS_I2C_XFER_SIZE_OFFSET 0x14 /* Transfer Size Register, RW */ 28 #define CDNS_I2C_TIME_OUT_OFFSET 0x1C /* Time Out Register, RW */ 29 #define CDNS_I2C_IMR_OFFSET 0x20 /* IRQ Mask Register, RO */ 30 #define CDNS_I2C_IER_OFFSET 0x24 /* IRQ Enable Register, WO */ 31 #define CDNS_I2C_IDR_OFFSET 0x28 /* IRQ Disable Register, WO */ 32 33 /* Control Register Bit mask definitions */ 34 #define CDNS_I2C_CR_HOLD BIT(4) /* Hold Bus bit */ 35 #define CDNS_I2C_CR_ACK_EN BIT(3) 36 #define CDNS_I2C_CR_NEA BIT(2) 37 #define CDNS_I2C_CR_MS BIT(1) 38 /* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */ 39 #define CDNS_I2C_CR_RW BIT(0) 40 /* 1 = Auto init FIFO to zeroes */ 41 #define CDNS_I2C_CR_CLR_FIFO BIT(6) 42 #define CDNS_I2C_CR_DIVA_SHIFT 14 43 #define CDNS_I2C_CR_DIVA_MASK (3 << CDNS_I2C_CR_DIVA_SHIFT) 44 #define CDNS_I2C_CR_DIVB_SHIFT 8 45 #define CDNS_I2C_CR_DIVB_MASK (0x3f << CDNS_I2C_CR_DIVB_SHIFT) 46 47 #define CDNS_I2C_CR_MASTER_EN_MASK (CDNS_I2C_CR_NEA | \ 48 CDNS_I2C_CR_ACK_EN | \ 49 CDNS_I2C_CR_MS) 50 51 #define CDNS_I2C_CR_SLAVE_EN_MASK ~CDNS_I2C_CR_MASTER_EN_MASK 52 53 /* Status Register Bit mask definitions */ 54 #define CDNS_I2C_SR_BA BIT(8) 55 #define CDNS_I2C_SR_TXDV BIT(6) 56 #define CDNS_I2C_SR_RXDV BIT(5) 57 #define CDNS_I2C_SR_RXRW BIT(3) 58 59 /* 60 * I2C Address Register Bit mask definitions 61 * Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0] 62 * bits. A write access to this register always initiates a transfer if the I2C 63 * is in master mode. 64 */ 65 #define CDNS_I2C_ADDR_MASK 0x000003FF /* I2C Address Mask */ 66 67 /* 68 * I2C Interrupt Registers Bit mask definitions 69 * All the four interrupt registers (Status/Mask/Enable/Disable) have the same 70 * bit definitions. 71 */ 72 #define CDNS_I2C_IXR_ARB_LOST BIT(9) 73 #define CDNS_I2C_IXR_RX_UNF BIT(7) 74 #define CDNS_I2C_IXR_TX_OVF BIT(6) 75 #define CDNS_I2C_IXR_RX_OVF BIT(5) 76 #define CDNS_I2C_IXR_SLV_RDY BIT(4) 77 #define CDNS_I2C_IXR_TO BIT(3) 78 #define CDNS_I2C_IXR_NACK BIT(2) 79 #define CDNS_I2C_IXR_DATA BIT(1) 80 #define CDNS_I2C_IXR_COMP BIT(0) 81 82 #define CDNS_I2C_IXR_ALL_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 83 CDNS_I2C_IXR_RX_UNF | \ 84 CDNS_I2C_IXR_TX_OVF | \ 85 CDNS_I2C_IXR_RX_OVF | \ 86 CDNS_I2C_IXR_SLV_RDY | \ 87 CDNS_I2C_IXR_TO | \ 88 CDNS_I2C_IXR_NACK | \ 89 CDNS_I2C_IXR_DATA | \ 90 CDNS_I2C_IXR_COMP) 91 92 #define CDNS_I2C_IXR_ERR_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 93 CDNS_I2C_IXR_RX_UNF | \ 94 CDNS_I2C_IXR_TX_OVF | \ 95 CDNS_I2C_IXR_RX_OVF | \ 96 CDNS_I2C_IXR_NACK) 97 98 #define CDNS_I2C_ENABLED_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \ 99 CDNS_I2C_IXR_RX_UNF | \ 100 CDNS_I2C_IXR_TX_OVF | \ 101 CDNS_I2C_IXR_RX_OVF | \ 102 CDNS_I2C_IXR_NACK | \ 103 CDNS_I2C_IXR_DATA | \ 104 CDNS_I2C_IXR_COMP) 105 106 #define CDNS_I2C_IXR_SLAVE_INTR_MASK (CDNS_I2C_IXR_RX_UNF | \ 107 CDNS_I2C_IXR_TX_OVF | \ 108 CDNS_I2C_IXR_RX_OVF | \ 109 CDNS_I2C_IXR_TO | \ 110 CDNS_I2C_IXR_NACK | \ 111 CDNS_I2C_IXR_DATA | \ 112 CDNS_I2C_IXR_COMP) 113 114 #define CDNS_I2C_TIMEOUT msecs_to_jiffies(1000) 115 /* timeout for pm runtime autosuspend */ 116 #define CNDS_I2C_PM_TIMEOUT 1000 /* ms */ 117 118 #define CDNS_I2C_FIFO_DEPTH_DEFAULT 16 119 #define CDNS_I2C_MAX_TRANSFER_SIZE 255 120 /* Transfer size in multiples of data interrupt depth */ 121 #define CDNS_I2C_TRANSFER_SIZE(max) ((max) - 3) 122 123 #define DRIVER_NAME "cdns-i2c" 124 125 #define CDNS_I2C_DIVA_MAX 4 126 #define CDNS_I2C_DIVB_MAX 64 127 128 #define CDNS_I2C_TIMEOUT_MAX 0xFF 129 130 #define CDNS_I2C_BROKEN_HOLD_BIT BIT(0) 131 #define CDNS_I2C_POLL_US 100000 132 #define CDNS_I2C_TIMEOUT_US 500000 133 134 #define cdns_i2c_readreg(offset) readl_relaxed(id->membase + offset) 135 #define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset) 136 137 #if IS_ENABLED(CONFIG_I2C_SLAVE) 138 /** 139 * enum cdns_i2c_mode - I2C Controller current operating mode 140 * 141 * @CDNS_I2C_MODE_SLAVE: I2C controller operating in slave mode 142 * @CDNS_I2C_MODE_MASTER: I2C Controller operating in master mode 143 */ 144 enum cdns_i2c_mode { 145 CDNS_I2C_MODE_SLAVE, 146 CDNS_I2C_MODE_MASTER, 147 }; 148 149 /** 150 * enum cdns_i2c_slave_state - Slave state when I2C is operating in slave mode 151 * 152 * @CDNS_I2C_SLAVE_STATE_IDLE: I2C slave idle 153 * @CDNS_I2C_SLAVE_STATE_SEND: I2C slave sending data to master 154 * @CDNS_I2C_SLAVE_STATE_RECV: I2C slave receiving data from master 155 */ 156 enum cdns_i2c_slave_state { 157 CDNS_I2C_SLAVE_STATE_IDLE, 158 CDNS_I2C_SLAVE_STATE_SEND, 159 CDNS_I2C_SLAVE_STATE_RECV, 160 }; 161 #endif 162 163 /** 164 * struct cdns_i2c - I2C device private data structure 165 * 166 * @dev: Pointer to device structure 167 * @membase: Base address of the I2C device 168 * @adap: I2C adapter instance 169 * @p_msg: Message pointer 170 * @err_status: Error status in Interrupt Status Register 171 * @xfer_done: Transfer complete status 172 * @p_send_buf: Pointer to transmit buffer 173 * @p_recv_buf: Pointer to receive buffer 174 * @send_count: Number of bytes still expected to send 175 * @recv_count: Number of bytes still expected to receive 176 * @curr_recv_count: Number of bytes to be received in current transfer 177 * @input_clk: Input clock to I2C controller 178 * @i2c_clk: Maximum I2C clock speed 179 * @bus_hold_flag: Flag used in repeated start for clearing HOLD bit 180 * @clk: Pointer to struct clk 181 * @clk_rate_change_nb: Notifier block for clock rate changes 182 * @reset: Reset control for the device 183 * @quirks: flag for broken hold bit usage in r1p10 184 * @ctrl_reg: Cached value of the control register. 185 * @rinfo: I2C GPIO recovery information 186 * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register 187 * @slave: Registered slave instance. 188 * @dev_mode: I2C operating role(master/slave). 189 * @slave_state: I2C Slave state(idle/read/write). 190 * @fifo_depth: The depth of the transfer FIFO 191 * @transfer_size: The maximum number of bytes in one transfer 192 */ 193 struct cdns_i2c { 194 struct device *dev; 195 void __iomem *membase; 196 struct i2c_adapter adap; 197 struct i2c_msg *p_msg; 198 int err_status; 199 struct completion xfer_done; 200 unsigned char *p_send_buf; 201 unsigned char *p_recv_buf; 202 unsigned int send_count; 203 unsigned int recv_count; 204 unsigned int curr_recv_count; 205 unsigned long input_clk; 206 unsigned int i2c_clk; 207 unsigned int bus_hold_flag; 208 struct clk *clk; 209 struct notifier_block clk_rate_change_nb; 210 struct reset_control *reset; 211 u32 quirks; 212 u32 ctrl_reg; 213 struct i2c_bus_recovery_info rinfo; 214 #if IS_ENABLED(CONFIG_I2C_SLAVE) 215 u16 ctrl_reg_diva_divb; 216 struct i2c_client *slave; 217 enum cdns_i2c_mode dev_mode; 218 enum cdns_i2c_slave_state slave_state; 219 #endif 220 u32 fifo_depth; 221 unsigned int transfer_size; 222 }; 223 224 struct cdns_platform_data { 225 u32 quirks; 226 }; 227 228 #define to_cdns_i2c(_nb) container_of(_nb, struct cdns_i2c, \ 229 clk_rate_change_nb) 230 231 /** 232 * cdns_i2c_clear_bus_hold - Clear bus hold bit 233 * @id: Pointer to driver data struct 234 * 235 * Helper to clear the controller's bus hold bit. 236 */ 237 static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id) 238 { 239 u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 240 if (reg & CDNS_I2C_CR_HOLD) 241 cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET); 242 } 243 244 static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround) 245 { 246 return (hold_wrkaround && 247 (id->curr_recv_count == id->fifo_depth + 1)); 248 } 249 250 #if IS_ENABLED(CONFIG_I2C_SLAVE) 251 static void cdns_i2c_set_mode(enum cdns_i2c_mode mode, struct cdns_i2c *id) 252 { 253 /* Disable all interrupts */ 254 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET); 255 256 /* Clear FIFO and transfer size */ 257 cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET); 258 259 /* Update device mode and state */ 260 id->dev_mode = mode; 261 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 262 263 switch (mode) { 264 case CDNS_I2C_MODE_MASTER: 265 /* Enable i2c master */ 266 cdns_i2c_writereg(id->ctrl_reg_diva_divb | 267 CDNS_I2C_CR_MASTER_EN_MASK, 268 CDNS_I2C_CR_OFFSET); 269 /* 270 * This delay is needed to give the IP some time to switch to 271 * the master mode. With lower values(like 110 us) i2cdetect 272 * will not detect any slave and without this delay, the IP will 273 * trigger a timeout interrupt. 274 */ 275 usleep_range(115, 125); 276 break; 277 case CDNS_I2C_MODE_SLAVE: 278 /* Enable i2c slave */ 279 cdns_i2c_writereg(id->ctrl_reg_diva_divb & 280 CDNS_I2C_CR_SLAVE_EN_MASK, 281 CDNS_I2C_CR_OFFSET); 282 283 /* Setting slave address */ 284 cdns_i2c_writereg(id->slave->addr & CDNS_I2C_ADDR_MASK, 285 CDNS_I2C_ADDR_OFFSET); 286 287 /* Enable slave send/receive interrupts */ 288 cdns_i2c_writereg(CDNS_I2C_IXR_SLAVE_INTR_MASK, 289 CDNS_I2C_IER_OFFSET); 290 break; 291 } 292 } 293 294 static void cdns_i2c_slave_rcv_data(struct cdns_i2c *id) 295 { 296 u8 bytes; 297 unsigned char data; 298 299 /* Prepare backend for data reception */ 300 if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) { 301 id->slave_state = CDNS_I2C_SLAVE_STATE_RECV; 302 i2c_slave_event(id->slave, I2C_SLAVE_WRITE_REQUESTED, NULL); 303 } 304 305 /* Fetch number of bytes to receive */ 306 bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 307 308 /* Read data and send to backend */ 309 while (bytes--) { 310 data = cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET); 311 i2c_slave_event(id->slave, I2C_SLAVE_WRITE_RECEIVED, &data); 312 } 313 } 314 315 static void cdns_i2c_slave_send_data(struct cdns_i2c *id) 316 { 317 u8 data; 318 319 /* Prepare backend for data transmission */ 320 if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) { 321 id->slave_state = CDNS_I2C_SLAVE_STATE_SEND; 322 i2c_slave_event(id->slave, I2C_SLAVE_READ_REQUESTED, &data); 323 } else { 324 i2c_slave_event(id->slave, I2C_SLAVE_READ_PROCESSED, &data); 325 } 326 327 /* Send data over bus */ 328 cdns_i2c_writereg(data, CDNS_I2C_DATA_OFFSET); 329 } 330 331 /** 332 * cdns_i2c_slave_isr - Interrupt handler for the I2C device in slave role 333 * @ptr: Pointer to I2C device private data 334 * 335 * This function handles the data interrupt and transfer complete interrupt of 336 * the I2C device in slave role. 337 * 338 * Return: IRQ_HANDLED always 339 */ 340 static irqreturn_t cdns_i2c_slave_isr(void *ptr) 341 { 342 struct cdns_i2c *id = ptr; 343 unsigned int isr_status, i2c_status; 344 345 /* Fetch the interrupt status */ 346 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 347 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 348 349 /* Ignore masked interrupts */ 350 isr_status &= ~cdns_i2c_readreg(CDNS_I2C_IMR_OFFSET); 351 352 /* Fetch transfer mode (send/receive) */ 353 i2c_status = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET); 354 355 /* Handle data send/receive */ 356 if (i2c_status & CDNS_I2C_SR_RXRW) { 357 /* Send data to master */ 358 if (isr_status & CDNS_I2C_IXR_DATA) 359 cdns_i2c_slave_send_data(id); 360 361 if (isr_status & CDNS_I2C_IXR_COMP) { 362 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 363 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 364 } 365 } else { 366 /* Receive data from master */ 367 if (isr_status & CDNS_I2C_IXR_DATA) 368 cdns_i2c_slave_rcv_data(id); 369 370 if (isr_status & CDNS_I2C_IXR_COMP) { 371 cdns_i2c_slave_rcv_data(id); 372 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 373 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 374 } 375 } 376 377 /* Master indicated xfer stop or fifo underflow/overflow */ 378 if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_RX_OVF | 379 CDNS_I2C_IXR_RX_UNF | CDNS_I2C_IXR_TX_OVF)) { 380 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 381 i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL); 382 cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET); 383 } 384 385 return IRQ_HANDLED; 386 } 387 #endif 388 389 /** 390 * cdns_i2c_master_isr - Interrupt handler for the I2C device in master role 391 * @ptr: Pointer to I2C device private data 392 * 393 * This function handles the data interrupt, transfer complete interrupt and 394 * the error interrupts of the I2C device in master role. 395 * 396 * Return: IRQ_HANDLED always 397 */ 398 static irqreturn_t cdns_i2c_master_isr(void *ptr) 399 { 400 unsigned int isr_status, avail_bytes; 401 unsigned int bytes_to_send; 402 bool updatetx; 403 struct cdns_i2c *id = ptr; 404 /* Signal completion only after everything is updated */ 405 int done_flag = 0; 406 irqreturn_t status = IRQ_NONE; 407 408 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 409 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 410 id->err_status = 0; 411 412 /* Handling nack and arbitration lost interrupt */ 413 if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) { 414 done_flag = 1; 415 status = IRQ_HANDLED; 416 } 417 418 /* 419 * Check if transfer size register needs to be updated again for a 420 * large data receive operation. 421 */ 422 updatetx = id->recv_count > id->curr_recv_count; 423 424 /* When receiving, handle data interrupt and completion interrupt */ 425 if (id->p_recv_buf && 426 ((isr_status & CDNS_I2C_IXR_COMP) || 427 (isr_status & CDNS_I2C_IXR_DATA))) { 428 /* Read data if receive data valid is set */ 429 while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & 430 CDNS_I2C_SR_RXDV) { 431 if (id->recv_count > 0) { 432 *(id->p_recv_buf)++ = 433 cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET); 434 id->recv_count--; 435 id->curr_recv_count--; 436 437 /* 438 * Clear hold bit that was set for FIFO control 439 * if RX data left is less than or equal to 440 * FIFO DEPTH unless repeated start is selected 441 */ 442 if (id->recv_count <= id->fifo_depth && 443 !id->bus_hold_flag) 444 cdns_i2c_clear_bus_hold(id); 445 446 } else { 447 dev_err(id->adap.dev.parent, 448 "xfer_size reg rollover. xfer aborted!\n"); 449 id->err_status |= CDNS_I2C_IXR_TO; 450 break; 451 } 452 453 if (cdns_is_holdquirk(id, updatetx)) 454 break; 455 } 456 457 /* 458 * The controller sends NACK to the slave when transfer size 459 * register reaches zero without considering the HOLD bit. 460 * This workaround is implemented for large data transfers to 461 * maintain transfer size non-zero while performing a large 462 * receive operation. 463 */ 464 if (cdns_is_holdquirk(id, updatetx)) { 465 /* wait while fifo is full */ 466 while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) != 467 (id->curr_recv_count - id->fifo_depth)) 468 ; 469 470 /* 471 * Check number of bytes to be received against maximum 472 * transfer size and update register accordingly. 473 */ 474 if (((int)(id->recv_count) - id->fifo_depth) > 475 id->transfer_size) { 476 cdns_i2c_writereg(id->transfer_size, 477 CDNS_I2C_XFER_SIZE_OFFSET); 478 id->curr_recv_count = id->transfer_size + 479 id->fifo_depth; 480 } else { 481 cdns_i2c_writereg(id->recv_count - 482 id->fifo_depth, 483 CDNS_I2C_XFER_SIZE_OFFSET); 484 id->curr_recv_count = id->recv_count; 485 } 486 } 487 488 /* Clear hold (if not repeated start) and signal completion */ 489 if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) { 490 if (!id->bus_hold_flag) 491 cdns_i2c_clear_bus_hold(id); 492 done_flag = 1; 493 } 494 495 status = IRQ_HANDLED; 496 } 497 498 /* When sending, handle transfer complete interrupt */ 499 if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) { 500 /* 501 * If there is more data to be sent, calculate the 502 * space available in FIFO and fill with that many bytes. 503 */ 504 if (id->send_count) { 505 avail_bytes = id->fifo_depth - 506 cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 507 if (id->send_count > avail_bytes) 508 bytes_to_send = avail_bytes; 509 else 510 bytes_to_send = id->send_count; 511 512 while (bytes_to_send--) { 513 cdns_i2c_writereg( 514 (*(id->p_send_buf)++), 515 CDNS_I2C_DATA_OFFSET); 516 id->send_count--; 517 } 518 } else { 519 /* 520 * Signal the completion of transaction and 521 * clear the hold bus bit if there are no 522 * further messages to be processed. 523 */ 524 done_flag = 1; 525 } 526 if (!id->send_count && !id->bus_hold_flag) 527 cdns_i2c_clear_bus_hold(id); 528 529 status = IRQ_HANDLED; 530 } 531 532 /* Update the status for errors */ 533 id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK; 534 if (id->err_status) 535 status = IRQ_HANDLED; 536 537 if (done_flag) 538 complete(&id->xfer_done); 539 540 return status; 541 } 542 543 /** 544 * cdns_i2c_isr - Interrupt handler for the I2C device 545 * @irq: irq number for the I2C device 546 * @ptr: void pointer to cdns_i2c structure 547 * 548 * This function passes the control to slave/master based on current role of 549 * i2c controller. 550 * 551 * Return: IRQ_HANDLED always 552 */ 553 static irqreturn_t cdns_i2c_isr(int irq, void *ptr) 554 { 555 #if IS_ENABLED(CONFIG_I2C_SLAVE) 556 struct cdns_i2c *id = ptr; 557 558 if (id->dev_mode == CDNS_I2C_MODE_SLAVE) 559 return cdns_i2c_slave_isr(ptr); 560 #endif 561 return cdns_i2c_master_isr(ptr); 562 } 563 564 /** 565 * cdns_i2c_mrecv - Prepare and start a master receive operation 566 * @id: pointer to the i2c device structure 567 */ 568 static void cdns_i2c_mrecv(struct cdns_i2c *id) 569 { 570 unsigned int ctrl_reg; 571 unsigned int isr_status; 572 unsigned long flags; 573 bool hold_clear = false; 574 bool irq_save = false; 575 576 u32 addr; 577 578 id->p_recv_buf = id->p_msg->buf; 579 id->recv_count = id->p_msg->len; 580 581 /* Put the controller in master receive mode and clear the FIFO */ 582 ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 583 ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO; 584 585 /* 586 * Receive up to I2C_SMBUS_BLOCK_MAX data bytes, plus one message length 587 * byte, plus one checksum byte if PEC is enabled. p_msg->len will be 2 if 588 * PEC is enabled, otherwise 1. 589 */ 590 if (id->p_msg->flags & I2C_M_RECV_LEN) 591 id->recv_count = I2C_SMBUS_BLOCK_MAX + id->p_msg->len; 592 593 id->curr_recv_count = id->recv_count; 594 595 /* 596 * Check for the message size against FIFO depth and set the 597 * 'hold bus' bit if it is greater than FIFO depth. 598 */ 599 if (id->recv_count > id->fifo_depth) 600 ctrl_reg |= CDNS_I2C_CR_HOLD; 601 602 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 603 604 /* Clear the interrupts in interrupt status register */ 605 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 606 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 607 608 /* 609 * The no. of bytes to receive is checked against the limit of 610 * max transfer size. Set transfer size register with no of bytes 611 * receive if it is less than transfer size and transfer size if 612 * it is more. Enable the interrupts. 613 */ 614 if (id->recv_count > id->transfer_size) { 615 cdns_i2c_writereg(id->transfer_size, 616 CDNS_I2C_XFER_SIZE_OFFSET); 617 id->curr_recv_count = id->transfer_size; 618 } else { 619 cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET); 620 } 621 622 /* Determine hold_clear based on number of bytes to receive and hold flag */ 623 if (!id->bus_hold_flag && id->recv_count <= id->fifo_depth) { 624 if (ctrl_reg & CDNS_I2C_CR_HOLD) { 625 hold_clear = true; 626 if (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) 627 irq_save = true; 628 } 629 } 630 631 addr = id->p_msg->addr; 632 addr &= CDNS_I2C_ADDR_MASK; 633 634 if (hold_clear) { 635 ctrl_reg &= ~CDNS_I2C_CR_HOLD; 636 ctrl_reg &= ~CDNS_I2C_CR_CLR_FIFO; 637 /* 638 * In case of Xilinx Zynq SOC, clear the HOLD bit before transfer size 639 * register reaches '0'. This is an IP bug which causes transfer size 640 * register overflow to 0xFF. To satisfy this timing requirement, 641 * disable the interrupts on current processor core between register 642 * writes to slave address register and control register. 643 */ 644 if (irq_save) 645 local_irq_save(flags); 646 647 cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET); 648 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 649 /* Read it back to avoid bufferring and make sure write happens */ 650 cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 651 652 if (irq_save) 653 local_irq_restore(flags); 654 } else { 655 cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET); 656 } 657 658 cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET); 659 } 660 661 /** 662 * cdns_i2c_msend - Prepare and start a master send operation 663 * @id: pointer to the i2c device 664 */ 665 static void cdns_i2c_msend(struct cdns_i2c *id) 666 { 667 unsigned int avail_bytes; 668 unsigned int bytes_to_send; 669 unsigned int ctrl_reg; 670 unsigned int isr_status; 671 672 id->p_recv_buf = NULL; 673 id->p_send_buf = id->p_msg->buf; 674 id->send_count = id->p_msg->len; 675 676 /* Set the controller in Master transmit mode and clear the FIFO. */ 677 ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 678 ctrl_reg &= ~CDNS_I2C_CR_RW; 679 ctrl_reg |= CDNS_I2C_CR_CLR_FIFO; 680 681 /* 682 * Check for the message size against FIFO depth and set the 683 * 'hold bus' bit if it is greater than FIFO depth. 684 */ 685 if (id->send_count > id->fifo_depth) 686 ctrl_reg |= CDNS_I2C_CR_HOLD; 687 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 688 689 /* Clear the interrupts in interrupt status register. */ 690 isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 691 cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET); 692 693 /* 694 * Calculate the space available in FIFO. Check the message length 695 * against the space available, and fill the FIFO accordingly. 696 * Enable the interrupts. 697 */ 698 avail_bytes = id->fifo_depth - 699 cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 700 701 if (id->send_count > avail_bytes) 702 bytes_to_send = avail_bytes; 703 else 704 bytes_to_send = id->send_count; 705 706 while (bytes_to_send--) { 707 cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET); 708 id->send_count--; 709 } 710 711 /* 712 * Clear the bus hold flag if there is no more data 713 * and if it is the last message. 714 */ 715 if (!id->bus_hold_flag && !id->send_count) 716 cdns_i2c_clear_bus_hold(id); 717 /* Set the slave address in address register - triggers operation. */ 718 cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK, 719 CDNS_I2C_ADDR_OFFSET); 720 721 cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET); 722 } 723 724 /** 725 * cdns_i2c_master_reset - Reset the interface 726 * @adap: pointer to the i2c adapter driver instance 727 * 728 * This function cleanup the fifos, clear the hold bit and status 729 * and disable the interrupts. 730 */ 731 static void cdns_i2c_master_reset(struct i2c_adapter *adap) 732 { 733 struct cdns_i2c *id = adap->algo_data; 734 u32 regval; 735 736 /* Disable the interrupts */ 737 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET); 738 /* Clear the hold bit and fifos */ 739 regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 740 regval &= ~CDNS_I2C_CR_HOLD; 741 regval |= CDNS_I2C_CR_CLR_FIFO; 742 cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET); 743 /* Update the transfercount register to zero */ 744 cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET); 745 /* Clear the interrupt status register */ 746 regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET); 747 cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET); 748 /* Clear the status register */ 749 regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET); 750 cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET); 751 } 752 753 static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg, 754 struct i2c_adapter *adap) 755 { 756 unsigned long time_left, msg_timeout; 757 u32 reg; 758 759 id->p_msg = msg; 760 id->err_status = 0; 761 reinit_completion(&id->xfer_done); 762 763 /* Check for the TEN Bit mode on each msg */ 764 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 765 if (msg->flags & I2C_M_TEN) { 766 if (reg & CDNS_I2C_CR_NEA) 767 cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA, 768 CDNS_I2C_CR_OFFSET); 769 } else { 770 if (!(reg & CDNS_I2C_CR_NEA)) 771 cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA, 772 CDNS_I2C_CR_OFFSET); 773 } 774 775 /* Check for the R/W flag on each msg */ 776 if (msg->flags & I2C_M_RD) 777 cdns_i2c_mrecv(id); 778 else 779 cdns_i2c_msend(id); 780 781 /* Minimal time to execute this message */ 782 msg_timeout = msecs_to_jiffies((1000 * msg->len * BITS_PER_BYTE) / id->i2c_clk); 783 /* Plus some wiggle room */ 784 msg_timeout += msecs_to_jiffies(500); 785 786 if (msg_timeout < adap->timeout) 787 msg_timeout = adap->timeout; 788 789 /* Wait for the signal of completion */ 790 time_left = wait_for_completion_timeout(&id->xfer_done, msg_timeout); 791 if (time_left == 0) { 792 cdns_i2c_master_reset(adap); 793 dev_err(id->adap.dev.parent, 794 "timeout waiting on completion\n"); 795 return -ETIMEDOUT; 796 } 797 798 cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, 799 CDNS_I2C_IDR_OFFSET); 800 801 /* If it is bus arbitration error, try again */ 802 if (id->err_status & CDNS_I2C_IXR_ARB_LOST) 803 return -EAGAIN; 804 805 if (msg->flags & I2C_M_RECV_LEN) 806 msg->len += min_t(unsigned int, msg->buf[0], I2C_SMBUS_BLOCK_MAX); 807 808 return 0; 809 } 810 811 /** 812 * cdns_i2c_master_xfer - The main i2c transfer function 813 * @adap: pointer to the i2c adapter driver instance 814 * @msgs: pointer to the i2c message structure 815 * @num: the number of messages to transfer 816 * 817 * Initiates the send/recv activity based on the transfer message received. 818 * 819 * Return: number of msgs processed on success, negative error otherwise 820 */ 821 static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, 822 int num) 823 { 824 int ret, count; 825 u32 reg; 826 struct cdns_i2c *id = adap->algo_data; 827 bool hold_quirk; 828 #if IS_ENABLED(CONFIG_I2C_SLAVE) 829 bool change_role = false; 830 #endif 831 832 ret = pm_runtime_resume_and_get(id->dev); 833 if (ret < 0) 834 return ret; 835 836 #if IS_ENABLED(CONFIG_I2C_SLAVE) 837 /* Check i2c operating mode and switch if possible */ 838 if (id->dev_mode == CDNS_I2C_MODE_SLAVE) { 839 if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE) { 840 ret = -EAGAIN; 841 goto out; 842 } 843 844 /* Set mode to master */ 845 cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id); 846 847 /* Mark flag to change role once xfer is completed */ 848 change_role = true; 849 } 850 #endif 851 852 /* Check if the bus is free */ 853 854 ret = readl_relaxed_poll_timeout(id->membase + CDNS_I2C_SR_OFFSET, 855 reg, 856 !(reg & CDNS_I2C_SR_BA), 857 CDNS_I2C_POLL_US, CDNS_I2C_TIMEOUT_US); 858 if (ret) { 859 ret = -EAGAIN; 860 if (id->adap.bus_recovery_info) 861 i2c_recover_bus(adap); 862 goto out; 863 } 864 865 hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT); 866 /* 867 * Set the flag to one when multiple messages are to be 868 * processed with a repeated start. 869 */ 870 if (num > 1) { 871 /* 872 * This controller does not give completion interrupt after a 873 * master receive message if HOLD bit is set (repeated start), 874 * resulting in SW timeout. Hence, if a receive message is 875 * followed by any other message, an error is returned 876 * indicating that this sequence is not supported. 877 */ 878 for (count = 0; (count < num - 1 && hold_quirk); count++) { 879 if (msgs[count].flags & I2C_M_RD) { 880 dev_warn(adap->dev.parent, 881 "Can't do repeated start after a receive message\n"); 882 ret = -EOPNOTSUPP; 883 goto out; 884 } 885 } 886 id->bus_hold_flag = 1; 887 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET); 888 reg |= CDNS_I2C_CR_HOLD; 889 cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET); 890 } else { 891 id->bus_hold_flag = 0; 892 } 893 894 /* Process the msg one by one */ 895 for (count = 0; count < num; count++, msgs++) { 896 if (count == (num - 1)) 897 id->bus_hold_flag = 0; 898 899 ret = cdns_i2c_process_msg(id, msgs, adap); 900 if (ret) 901 goto out; 902 903 /* Report the other error interrupts to application */ 904 if (id->err_status) { 905 cdns_i2c_master_reset(adap); 906 907 if (id->err_status & CDNS_I2C_IXR_NACK) { 908 ret = -ENXIO; 909 goto out; 910 } 911 ret = -EIO; 912 goto out; 913 } 914 } 915 916 ret = num; 917 918 out: 919 920 #if IS_ENABLED(CONFIG_I2C_SLAVE) 921 /* Switch i2c mode to slave */ 922 if (change_role) 923 cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id); 924 #endif 925 926 pm_runtime_mark_last_busy(id->dev); 927 pm_runtime_put_autosuspend(id->dev); 928 return ret; 929 } 930 931 /** 932 * cdns_i2c_func - Returns the supported features of the I2C driver 933 * @adap: pointer to the i2c adapter structure 934 * 935 * Return: 32 bit value, each bit corresponding to a feature 936 */ 937 static u32 cdns_i2c_func(struct i2c_adapter *adap) 938 { 939 u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR | 940 (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | 941 I2C_FUNC_SMBUS_BLOCK_DATA; 942 943 #if IS_ENABLED(CONFIG_I2C_SLAVE) 944 func |= I2C_FUNC_SLAVE; 945 #endif 946 947 return func; 948 } 949 950 #if IS_ENABLED(CONFIG_I2C_SLAVE) 951 static int cdns_reg_slave(struct i2c_client *slave) 952 { 953 int ret; 954 struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c, 955 adap); 956 957 if (id->slave) 958 return -EBUSY; 959 960 if (slave->flags & I2C_CLIENT_TEN) 961 return -EAFNOSUPPORT; 962 963 ret = pm_runtime_resume_and_get(id->dev); 964 if (ret < 0) 965 return ret; 966 967 /* Store slave information */ 968 id->slave = slave; 969 970 /* Enable I2C slave */ 971 cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id); 972 973 return 0; 974 } 975 976 static int cdns_unreg_slave(struct i2c_client *slave) 977 { 978 struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c, 979 adap); 980 981 pm_runtime_put(id->dev); 982 983 /* Remove slave information */ 984 id->slave = NULL; 985 986 /* Enable I2C master */ 987 cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id); 988 989 return 0; 990 } 991 #endif 992 993 static const struct i2c_algorithm cdns_i2c_algo = { 994 .master_xfer = cdns_i2c_master_xfer, 995 .functionality = cdns_i2c_func, 996 #if IS_ENABLED(CONFIG_I2C_SLAVE) 997 .reg_slave = cdns_reg_slave, 998 .unreg_slave = cdns_unreg_slave, 999 #endif 1000 }; 1001 1002 /** 1003 * cdns_i2c_calc_divs - Calculate clock dividers 1004 * @f: I2C clock frequency 1005 * @input_clk: Input clock frequency 1006 * @a: First divider (return value) 1007 * @b: Second divider (return value) 1008 * 1009 * f is used as input and output variable. As input it is used as target I2C 1010 * frequency. On function exit f holds the actually resulting I2C frequency. 1011 * 1012 * Return: 0 on success, negative errno otherwise. 1013 */ 1014 static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk, 1015 unsigned int *a, unsigned int *b) 1016 { 1017 unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp; 1018 unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0; 1019 unsigned int last_error, current_error; 1020 1021 /* calculate (divisor_a+1) x (divisor_b+1) */ 1022 temp = input_clk / (22 * fscl); 1023 1024 /* 1025 * If the calculated value is negative or 0, the fscl input is out of 1026 * range. Return error. 1027 */ 1028 if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX))) 1029 return -EINVAL; 1030 1031 last_error = -1; 1032 for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) { 1033 div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1)); 1034 1035 if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX)) 1036 continue; 1037 div_b--; 1038 1039 actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1)); 1040 1041 if (actual_fscl > fscl) 1042 continue; 1043 1044 current_error = fscl - actual_fscl; 1045 1046 if (last_error > current_error) { 1047 calc_div_a = div_a; 1048 calc_div_b = div_b; 1049 best_fscl = actual_fscl; 1050 last_error = current_error; 1051 } 1052 } 1053 1054 *a = calc_div_a; 1055 *b = calc_div_b; 1056 *f = best_fscl; 1057 1058 return 0; 1059 } 1060 1061 /** 1062 * cdns_i2c_setclk - This function sets the serial clock rate for the I2C device 1063 * @clk_in: I2C clock input frequency in Hz 1064 * @id: Pointer to the I2C device structure 1065 * 1066 * The device must be idle rather than busy transferring data before setting 1067 * these device options. 1068 * The data rate is set by values in the control register. 1069 * The formula for determining the correct register values is 1070 * Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1)) 1071 * See the hardware data sheet for a full explanation of setting the serial 1072 * clock rate. The clock can not be faster than the input clock divide by 22. 1073 * The two most common clock rates are 100KHz and 400KHz. 1074 * 1075 * Return: 0 on success, negative error otherwise 1076 */ 1077 static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id) 1078 { 1079 unsigned int div_a, div_b; 1080 unsigned int ctrl_reg; 1081 int ret = 0; 1082 unsigned long fscl = id->i2c_clk; 1083 1084 ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b); 1085 if (ret) 1086 return ret; 1087 1088 ctrl_reg = id->ctrl_reg; 1089 ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK); 1090 ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) | 1091 (div_b << CDNS_I2C_CR_DIVB_SHIFT)); 1092 id->ctrl_reg = ctrl_reg; 1093 cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET); 1094 #if IS_ENABLED(CONFIG_I2C_SLAVE) 1095 id->ctrl_reg_diva_divb = ctrl_reg & (CDNS_I2C_CR_DIVA_MASK | 1096 CDNS_I2C_CR_DIVB_MASK); 1097 #endif 1098 return 0; 1099 } 1100 1101 /** 1102 * cdns_i2c_clk_notifier_cb - Clock rate change callback 1103 * @nb: Pointer to notifier block 1104 * @event: Notification reason 1105 * @data: Pointer to notification data object 1106 * 1107 * This function is called when the cdns_i2c input clock frequency changes. 1108 * The callback checks whether a valid bus frequency can be generated after the 1109 * change. If so, the change is acknowledged, otherwise the change is aborted. 1110 * New dividers are written to the HW in the pre- or post change notification 1111 * depending on the scaling direction. 1112 * 1113 * Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK 1114 * to acknowledge the change, NOTIFY_DONE if the notification is 1115 * considered irrelevant. 1116 */ 1117 static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long 1118 event, void *data) 1119 { 1120 struct clk_notifier_data *ndata = data; 1121 struct cdns_i2c *id = to_cdns_i2c(nb); 1122 1123 if (pm_runtime_suspended(id->dev)) 1124 return NOTIFY_OK; 1125 1126 switch (event) { 1127 case PRE_RATE_CHANGE: 1128 { 1129 unsigned long input_clk = ndata->new_rate; 1130 unsigned long fscl = id->i2c_clk; 1131 unsigned int div_a, div_b; 1132 int ret; 1133 1134 ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b); 1135 if (ret) { 1136 dev_warn(id->adap.dev.parent, 1137 "clock rate change rejected\n"); 1138 return NOTIFY_STOP; 1139 } 1140 1141 /* scale up */ 1142 if (ndata->new_rate > ndata->old_rate) 1143 cdns_i2c_setclk(ndata->new_rate, id); 1144 1145 return NOTIFY_OK; 1146 } 1147 case POST_RATE_CHANGE: 1148 id->input_clk = ndata->new_rate; 1149 /* scale down */ 1150 if (ndata->new_rate < ndata->old_rate) 1151 cdns_i2c_setclk(ndata->new_rate, id); 1152 return NOTIFY_OK; 1153 case ABORT_RATE_CHANGE: 1154 /* scale up */ 1155 if (ndata->new_rate > ndata->old_rate) 1156 cdns_i2c_setclk(ndata->old_rate, id); 1157 return NOTIFY_OK; 1158 default: 1159 return NOTIFY_DONE; 1160 } 1161 } 1162 1163 /** 1164 * cdns_i2c_runtime_suspend - Runtime suspend method for the driver 1165 * @dev: Address of the platform_device structure 1166 * 1167 * Put the driver into low power mode. 1168 * 1169 * Return: 0 always 1170 */ 1171 static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev) 1172 { 1173 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1174 1175 clk_disable(xi2c->clk); 1176 1177 return 0; 1178 } 1179 1180 /** 1181 * cdns_i2c_init - Controller initialisation 1182 * @id: Device private data structure 1183 * 1184 * Initialise the i2c controller. 1185 * 1186 */ 1187 static void cdns_i2c_init(struct cdns_i2c *id) 1188 { 1189 cdns_i2c_writereg(id->ctrl_reg, CDNS_I2C_CR_OFFSET); 1190 /* 1191 * Cadence I2C controller has a bug wherein it generates 1192 * invalid read transaction after HW timeout in master receiver mode. 1193 * HW timeout is not used by this driver and the interrupt is disabled. 1194 * But the feature itself cannot be disabled. Hence maximum value 1195 * is written to this register to reduce the chances of error. 1196 */ 1197 cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET); 1198 } 1199 1200 /** 1201 * cdns_i2c_runtime_resume - Runtime resume 1202 * @dev: Address of the platform_device structure 1203 * 1204 * Runtime resume callback. 1205 * 1206 * Return: 0 on success and error value on error 1207 */ 1208 static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev) 1209 { 1210 struct cdns_i2c *xi2c = dev_get_drvdata(dev); 1211 int ret; 1212 1213 ret = clk_enable(xi2c->clk); 1214 if (ret) { 1215 dev_err(dev, "Cannot enable clock.\n"); 1216 return ret; 1217 } 1218 cdns_i2c_init(xi2c); 1219 1220 return 0; 1221 } 1222 1223 static const struct dev_pm_ops cdns_i2c_dev_pm_ops = { 1224 SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend, 1225 cdns_i2c_runtime_resume, NULL) 1226 }; 1227 1228 static const struct cdns_platform_data r1p10_i2c_def = { 1229 .quirks = CDNS_I2C_BROKEN_HOLD_BIT, 1230 }; 1231 1232 static const struct of_device_id cdns_i2c_of_match[] = { 1233 { .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def }, 1234 { .compatible = "cdns,i2c-r1p14",}, 1235 { /* end of table */ } 1236 }; 1237 MODULE_DEVICE_TABLE(of, cdns_i2c_of_match); 1238 1239 /** 1240 * cdns_i2c_detect_transfer_size - Detect the maximum transfer size supported 1241 * @id: Device private data structure 1242 * 1243 * Detect the maximum transfer size that is supported by this instance of the 1244 * Cadence I2C controller. 1245 */ 1246 static void cdns_i2c_detect_transfer_size(struct cdns_i2c *id) 1247 { 1248 u32 val; 1249 1250 /* 1251 * Writing to the transfer size register is only possible if these two bits 1252 * are set in the control register. 1253 */ 1254 cdns_i2c_writereg(CDNS_I2C_CR_MS | CDNS_I2C_CR_RW, CDNS_I2C_CR_OFFSET); 1255 1256 /* 1257 * The number of writable bits of the transfer size register can be between 1258 * 4 and 8. This is a controlled through a synthesis parameter of the IP 1259 * core and can vary from instance to instance. The unused MSBs always read 1260 * back as 0. Writing 0xff and then reading the value back will report the 1261 * maximum supported transfer size. 1262 */ 1263 cdns_i2c_writereg(CDNS_I2C_MAX_TRANSFER_SIZE, CDNS_I2C_XFER_SIZE_OFFSET); 1264 val = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET); 1265 id->transfer_size = CDNS_I2C_TRANSFER_SIZE(val); 1266 cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET); 1267 cdns_i2c_writereg(0, CDNS_I2C_CR_OFFSET); 1268 } 1269 1270 /** 1271 * cdns_i2c_probe - Platform registration call 1272 * @pdev: Handle to the platform device structure 1273 * 1274 * This function does all the memory allocation and registration for the i2c 1275 * device. User can modify the address mode to 10 bit address mode using the 1276 * ioctl call with option I2C_TENBIT. 1277 * 1278 * Return: 0 on success, negative error otherwise 1279 */ 1280 static int cdns_i2c_probe(struct platform_device *pdev) 1281 { 1282 struct resource *r_mem; 1283 struct cdns_i2c *id; 1284 int ret, irq; 1285 const struct of_device_id *match; 1286 1287 id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL); 1288 if (!id) 1289 return -ENOMEM; 1290 1291 id->dev = &pdev->dev; 1292 platform_set_drvdata(pdev, id); 1293 1294 match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node); 1295 if (match && match->data) { 1296 const struct cdns_platform_data *data = match->data; 1297 id->quirks = data->quirks; 1298 } 1299 1300 id->rinfo.pinctrl = devm_pinctrl_get(&pdev->dev); 1301 if (IS_ERR(id->rinfo.pinctrl)) { 1302 int err = PTR_ERR(id->rinfo.pinctrl); 1303 1304 dev_info(&pdev->dev, "can't get pinctrl, bus recovery not supported\n"); 1305 if (err != -ENODEV) 1306 return err; 1307 } else { 1308 id->adap.bus_recovery_info = &id->rinfo; 1309 } 1310 1311 id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem); 1312 if (IS_ERR(id->membase)) 1313 return PTR_ERR(id->membase); 1314 1315 irq = platform_get_irq(pdev, 0); 1316 if (irq < 0) 1317 return irq; 1318 1319 id->adap.owner = THIS_MODULE; 1320 id->adap.dev.of_node = pdev->dev.of_node; 1321 id->adap.algo = &cdns_i2c_algo; 1322 id->adap.timeout = CDNS_I2C_TIMEOUT; 1323 id->adap.retries = 3; /* Default retry value. */ 1324 id->adap.algo_data = id; 1325 id->adap.dev.parent = &pdev->dev; 1326 init_completion(&id->xfer_done); 1327 snprintf(id->adap.name, sizeof(id->adap.name), 1328 "Cadence I2C at %08lx", (unsigned long)r_mem->start); 1329 1330 id->clk = devm_clk_get(&pdev->dev, NULL); 1331 if (IS_ERR(id->clk)) 1332 return dev_err_probe(&pdev->dev, PTR_ERR(id->clk), 1333 "input clock not found.\n"); 1334 1335 id->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL); 1336 if (IS_ERR(id->reset)) 1337 return dev_err_probe(&pdev->dev, PTR_ERR(id->reset), 1338 "Failed to request reset.\n"); 1339 1340 ret = clk_prepare_enable(id->clk); 1341 if (ret) 1342 dev_err(&pdev->dev, "Unable to enable clock.\n"); 1343 1344 ret = reset_control_deassert(id->reset); 1345 if (ret) { 1346 dev_err_probe(&pdev->dev, ret, 1347 "Failed to de-assert reset.\n"); 1348 goto err_clk_dis; 1349 } 1350 1351 pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT); 1352 pm_runtime_use_autosuspend(id->dev); 1353 pm_runtime_set_active(id->dev); 1354 pm_runtime_enable(id->dev); 1355 1356 id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb; 1357 if (clk_notifier_register(id->clk, &id->clk_rate_change_nb)) 1358 dev_warn(&pdev->dev, "Unable to register clock notifier.\n"); 1359 id->input_clk = clk_get_rate(id->clk); 1360 1361 ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency", 1362 &id->i2c_clk); 1363 if (ret || (id->i2c_clk > I2C_MAX_FAST_MODE_FREQ)) 1364 id->i2c_clk = I2C_MAX_STANDARD_MODE_FREQ; 1365 1366 #if IS_ENABLED(CONFIG_I2C_SLAVE) 1367 /* Set initial mode to master */ 1368 id->dev_mode = CDNS_I2C_MODE_MASTER; 1369 id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE; 1370 #endif 1371 id->ctrl_reg = CDNS_I2C_CR_ACK_EN | CDNS_I2C_CR_NEA | CDNS_I2C_CR_MS; 1372 1373 id->fifo_depth = CDNS_I2C_FIFO_DEPTH_DEFAULT; 1374 of_property_read_u32(pdev->dev.of_node, "fifo-depth", &id->fifo_depth); 1375 1376 cdns_i2c_detect_transfer_size(id); 1377 1378 ret = cdns_i2c_setclk(id->input_clk, id); 1379 if (ret) { 1380 dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk); 1381 ret = -EINVAL; 1382 goto err_clk_notifier_unregister; 1383 } 1384 1385 ret = devm_request_irq(&pdev->dev, irq, cdns_i2c_isr, 0, 1386 DRIVER_NAME, id); 1387 if (ret) { 1388 dev_err(&pdev->dev, "cannot get irq %d\n", irq); 1389 goto err_clk_notifier_unregister; 1390 } 1391 cdns_i2c_init(id); 1392 1393 ret = i2c_add_adapter(&id->adap); 1394 if (ret < 0) 1395 goto err_clk_notifier_unregister; 1396 1397 dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n", 1398 id->i2c_clk / 1000, (unsigned long)r_mem->start, irq); 1399 1400 return 0; 1401 1402 err_clk_notifier_unregister: 1403 clk_notifier_unregister(id->clk, &id->clk_rate_change_nb); 1404 reset_control_assert(id->reset); 1405 err_clk_dis: 1406 clk_disable_unprepare(id->clk); 1407 pm_runtime_disable(&pdev->dev); 1408 pm_runtime_set_suspended(&pdev->dev); 1409 return ret; 1410 } 1411 1412 /** 1413 * cdns_i2c_remove - Unregister the device after releasing the resources 1414 * @pdev: Handle to the platform device structure 1415 * 1416 * This function frees all the resources allocated to the device. 1417 * 1418 * Return: 0 always 1419 */ 1420 static void cdns_i2c_remove(struct platform_device *pdev) 1421 { 1422 struct cdns_i2c *id = platform_get_drvdata(pdev); 1423 1424 pm_runtime_disable(&pdev->dev); 1425 pm_runtime_set_suspended(&pdev->dev); 1426 pm_runtime_dont_use_autosuspend(&pdev->dev); 1427 1428 i2c_del_adapter(&id->adap); 1429 clk_notifier_unregister(id->clk, &id->clk_rate_change_nb); 1430 reset_control_assert(id->reset); 1431 clk_disable_unprepare(id->clk); 1432 } 1433 1434 static struct platform_driver cdns_i2c_drv = { 1435 .driver = { 1436 .name = DRIVER_NAME, 1437 .of_match_table = cdns_i2c_of_match, 1438 .pm = &cdns_i2c_dev_pm_ops, 1439 }, 1440 .probe = cdns_i2c_probe, 1441 .remove_new = cdns_i2c_remove, 1442 }; 1443 1444 module_platform_driver(cdns_i2c_drv); 1445 1446 MODULE_AUTHOR("Xilinx Inc."); 1447 MODULE_DESCRIPTION("Cadence I2C bus driver"); 1448 MODULE_LICENSE("GPL"); 1449