xref: /openbmc/linux/drivers/i2c/busses/i2c-cadence.c (revision 2540d3c9)
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * I2C bus driver for the Cadence I2C controller.
4  *
5  * Copyright (C) 2009 - 2014 Xilinx, Inc.
6  */
7 
8 #include <linux/clk.h>
9 #include <linux/delay.h>
10 #include <linux/i2c.h>
11 #include <linux/interrupt.h>
12 #include <linux/io.h>
13 #include <linux/module.h>
14 #include <linux/platform_device.h>
15 #include <linux/of.h>
16 #include <linux/pm_runtime.h>
17 
18 /* Register offsets for the I2C device. */
19 #define CDNS_I2C_CR_OFFSET		0x00 /* Control Register, RW */
20 #define CDNS_I2C_SR_OFFSET		0x04 /* Status Register, RO */
21 #define CDNS_I2C_ADDR_OFFSET		0x08 /* I2C Address Register, RW */
22 #define CDNS_I2C_DATA_OFFSET		0x0C /* I2C Data Register, RW */
23 #define CDNS_I2C_ISR_OFFSET		0x10 /* IRQ Status Register, RW */
24 #define CDNS_I2C_XFER_SIZE_OFFSET	0x14 /* Transfer Size Register, RW */
25 #define CDNS_I2C_TIME_OUT_OFFSET	0x1C /* Time Out Register, RW */
26 #define CDNS_I2C_IMR_OFFSET		0x20 /* IRQ Mask Register, RO */
27 #define CDNS_I2C_IER_OFFSET		0x24 /* IRQ Enable Register, WO */
28 #define CDNS_I2C_IDR_OFFSET		0x28 /* IRQ Disable Register, WO */
29 
30 /* Control Register Bit mask definitions */
31 #define CDNS_I2C_CR_HOLD		BIT(4) /* Hold Bus bit */
32 #define CDNS_I2C_CR_ACK_EN		BIT(3)
33 #define CDNS_I2C_CR_NEA			BIT(2)
34 #define CDNS_I2C_CR_MS			BIT(1)
35 /* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */
36 #define CDNS_I2C_CR_RW			BIT(0)
37 /* 1 = Auto init FIFO to zeroes */
38 #define CDNS_I2C_CR_CLR_FIFO		BIT(6)
39 #define CDNS_I2C_CR_DIVA_SHIFT		14
40 #define CDNS_I2C_CR_DIVA_MASK		(3 << CDNS_I2C_CR_DIVA_SHIFT)
41 #define CDNS_I2C_CR_DIVB_SHIFT		8
42 #define CDNS_I2C_CR_DIVB_MASK		(0x3f << CDNS_I2C_CR_DIVB_SHIFT)
43 
44 #define CDNS_I2C_CR_MASTER_EN_MASK	(CDNS_I2C_CR_NEA | \
45 					 CDNS_I2C_CR_ACK_EN | \
46 					 CDNS_I2C_CR_MS)
47 
48 #define CDNS_I2C_CR_SLAVE_EN_MASK	~CDNS_I2C_CR_MASTER_EN_MASK
49 
50 /* Status Register Bit mask definitions */
51 #define CDNS_I2C_SR_BA		BIT(8)
52 #define CDNS_I2C_SR_TXDV	BIT(6)
53 #define CDNS_I2C_SR_RXDV	BIT(5)
54 #define CDNS_I2C_SR_RXRW	BIT(3)
55 
56 /*
57  * I2C Address Register Bit mask definitions
58  * Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0]
59  * bits. A write access to this register always initiates a transfer if the I2C
60  * is in master mode.
61  */
62 #define CDNS_I2C_ADDR_MASK	0x000003FF /* I2C Address Mask */
63 
64 /*
65  * I2C Interrupt Registers Bit mask definitions
66  * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
67  * bit definitions.
68  */
69 #define CDNS_I2C_IXR_ARB_LOST		BIT(9)
70 #define CDNS_I2C_IXR_RX_UNF		BIT(7)
71 #define CDNS_I2C_IXR_TX_OVF		BIT(6)
72 #define CDNS_I2C_IXR_RX_OVF		BIT(5)
73 #define CDNS_I2C_IXR_SLV_RDY		BIT(4)
74 #define CDNS_I2C_IXR_TO			BIT(3)
75 #define CDNS_I2C_IXR_NACK		BIT(2)
76 #define CDNS_I2C_IXR_DATA		BIT(1)
77 #define CDNS_I2C_IXR_COMP		BIT(0)
78 
79 #define CDNS_I2C_IXR_ALL_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
80 					 CDNS_I2C_IXR_RX_UNF | \
81 					 CDNS_I2C_IXR_TX_OVF | \
82 					 CDNS_I2C_IXR_RX_OVF | \
83 					 CDNS_I2C_IXR_SLV_RDY | \
84 					 CDNS_I2C_IXR_TO | \
85 					 CDNS_I2C_IXR_NACK | \
86 					 CDNS_I2C_IXR_DATA | \
87 					 CDNS_I2C_IXR_COMP)
88 
89 #define CDNS_I2C_IXR_ERR_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
90 					 CDNS_I2C_IXR_RX_UNF | \
91 					 CDNS_I2C_IXR_TX_OVF | \
92 					 CDNS_I2C_IXR_RX_OVF | \
93 					 CDNS_I2C_IXR_NACK)
94 
95 #define CDNS_I2C_ENABLED_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
96 					 CDNS_I2C_IXR_RX_UNF | \
97 					 CDNS_I2C_IXR_TX_OVF | \
98 					 CDNS_I2C_IXR_RX_OVF | \
99 					 CDNS_I2C_IXR_NACK | \
100 					 CDNS_I2C_IXR_DATA | \
101 					 CDNS_I2C_IXR_COMP)
102 
103 #define CDNS_I2C_IXR_SLAVE_INTR_MASK	(CDNS_I2C_IXR_RX_UNF | \
104 					 CDNS_I2C_IXR_TX_OVF | \
105 					 CDNS_I2C_IXR_RX_OVF | \
106 					 CDNS_I2C_IXR_TO | \
107 					 CDNS_I2C_IXR_NACK | \
108 					 CDNS_I2C_IXR_DATA | \
109 					 CDNS_I2C_IXR_COMP)
110 
111 #define CDNS_I2C_TIMEOUT		msecs_to_jiffies(1000)
112 /* timeout for pm runtime autosuspend */
113 #define CNDS_I2C_PM_TIMEOUT		1000	/* ms */
114 
115 #define CDNS_I2C_FIFO_DEPTH		16
116 /* FIFO depth at which the DATA interrupt occurs */
117 #define CDNS_I2C_DATA_INTR_DEPTH	(CDNS_I2C_FIFO_DEPTH - 2)
118 #define CDNS_I2C_MAX_TRANSFER_SIZE	255
119 /* Transfer size in multiples of data interrupt depth */
120 #define CDNS_I2C_TRANSFER_SIZE	(CDNS_I2C_MAX_TRANSFER_SIZE - 3)
121 
122 #define DRIVER_NAME		"cdns-i2c"
123 
124 #define CDNS_I2C_DIVA_MAX	4
125 #define CDNS_I2C_DIVB_MAX	64
126 
127 #define CDNS_I2C_TIMEOUT_MAX	0xFF
128 
129 #define CDNS_I2C_BROKEN_HOLD_BIT	BIT(0)
130 
131 #define cdns_i2c_readreg(offset)       readl_relaxed(id->membase + offset)
132 #define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
133 
134 #if IS_ENABLED(CONFIG_I2C_SLAVE)
135 /**
136  * enum cdns_i2c_mode - I2C Controller current operating mode
137  *
138  * @CDNS_I2C_MODE_SLAVE:       I2C controller operating in slave mode
139  * @CDNS_I2C_MODE_MASTER:      I2C Controller operating in master mode
140  */
141 enum cdns_i2c_mode {
142 	CDNS_I2C_MODE_SLAVE,
143 	CDNS_I2C_MODE_MASTER,
144 };
145 
146 /**
147  * enum cdns_i2c_slave_state - Slave state when I2C is operating in slave mode
148  *
149  * @CDNS_I2C_SLAVE_STATE_IDLE: I2C slave idle
150  * @CDNS_I2C_SLAVE_STATE_SEND: I2C slave sending data to master
151  * @CDNS_I2C_SLAVE_STATE_RECV: I2C slave receiving data from master
152  */
153 enum cdns_i2c_slave_state {
154 	CDNS_I2C_SLAVE_STATE_IDLE,
155 	CDNS_I2C_SLAVE_STATE_SEND,
156 	CDNS_I2C_SLAVE_STATE_RECV,
157 };
158 #endif
159 
160 /**
161  * struct cdns_i2c - I2C device private data structure
162  *
163  * @dev:		Pointer to device structure
164  * @membase:		Base address of the I2C device
165  * @adap:		I2C adapter instance
166  * @p_msg:		Message pointer
167  * @err_status:		Error status in Interrupt Status Register
168  * @xfer_done:		Transfer complete status
169  * @p_send_buf:		Pointer to transmit buffer
170  * @p_recv_buf:		Pointer to receive buffer
171  * @send_count:		Number of bytes still expected to send
172  * @recv_count:		Number of bytes still expected to receive
173  * @curr_recv_count:	Number of bytes to be received in current transfer
174  * @irq:		IRQ number
175  * @input_clk:		Input clock to I2C controller
176  * @i2c_clk:		Maximum I2C clock speed
177  * @bus_hold_flag:	Flag used in repeated start for clearing HOLD bit
178  * @clk:		Pointer to struct clk
179  * @clk_rate_change_nb:	Notifier block for clock rate changes
180  * @quirks:		flag for broken hold bit usage in r1p10
181  * @ctrl_reg:		Cached value of the control register.
182  * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register
183  * @slave:		Registered slave instance.
184  * @dev_mode:		I2C operating role(master/slave).
185  * @slave_state:	I2C Slave state(idle/read/write).
186  */
187 struct cdns_i2c {
188 	struct device		*dev;
189 	void __iomem *membase;
190 	struct i2c_adapter adap;
191 	struct i2c_msg *p_msg;
192 	int err_status;
193 	struct completion xfer_done;
194 	unsigned char *p_send_buf;
195 	unsigned char *p_recv_buf;
196 	unsigned int send_count;
197 	unsigned int recv_count;
198 	unsigned int curr_recv_count;
199 	int irq;
200 	unsigned long input_clk;
201 	unsigned int i2c_clk;
202 	unsigned int bus_hold_flag;
203 	struct clk *clk;
204 	struct notifier_block clk_rate_change_nb;
205 	u32 quirks;
206 	u32 ctrl_reg;
207 #if IS_ENABLED(CONFIG_I2C_SLAVE)
208 	u16 ctrl_reg_diva_divb;
209 	struct i2c_client *slave;
210 	enum cdns_i2c_mode dev_mode;
211 	enum cdns_i2c_slave_state slave_state;
212 #endif
213 };
214 
215 struct cdns_platform_data {
216 	u32 quirks;
217 };
218 
219 #define to_cdns_i2c(_nb)	container_of(_nb, struct cdns_i2c, \
220 					     clk_rate_change_nb)
221 
222 /**
223  * cdns_i2c_clear_bus_hold - Clear bus hold bit
224  * @id:	Pointer to driver data struct
225  *
226  * Helper to clear the controller's bus hold bit.
227  */
228 static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id)
229 {
230 	u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
231 	if (reg & CDNS_I2C_CR_HOLD)
232 		cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET);
233 }
234 
235 static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround)
236 {
237 	return (hold_wrkaround &&
238 		(id->curr_recv_count == CDNS_I2C_FIFO_DEPTH + 1));
239 }
240 
241 #if IS_ENABLED(CONFIG_I2C_SLAVE)
242 static void cdns_i2c_set_mode(enum cdns_i2c_mode mode, struct cdns_i2c *id)
243 {
244 	/* Disable all interrupts */
245 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
246 
247 	/* Clear FIFO and transfer size */
248 	cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
249 
250 	/* Update device mode and state */
251 	id->dev_mode = mode;
252 	id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
253 
254 	switch (mode) {
255 	case CDNS_I2C_MODE_MASTER:
256 		/* Enable i2c master */
257 		cdns_i2c_writereg(id->ctrl_reg_diva_divb |
258 				  CDNS_I2C_CR_MASTER_EN_MASK,
259 				  CDNS_I2C_CR_OFFSET);
260 		/*
261 		 * This delay is needed to give the IP some time to switch to
262 		 * the master mode. With lower values(like 110 us) i2cdetect
263 		 * will not detect any slave and without this delay, the IP will
264 		 * trigger a timeout interrupt.
265 		 */
266 		usleep_range(115, 125);
267 		break;
268 	case CDNS_I2C_MODE_SLAVE:
269 		/* Enable i2c slave */
270 		cdns_i2c_writereg(id->ctrl_reg_diva_divb &
271 				  CDNS_I2C_CR_SLAVE_EN_MASK,
272 				  CDNS_I2C_CR_OFFSET);
273 
274 		/* Setting slave address */
275 		cdns_i2c_writereg(id->slave->addr & CDNS_I2C_ADDR_MASK,
276 				  CDNS_I2C_ADDR_OFFSET);
277 
278 		/* Enable slave send/receive interrupts */
279 		cdns_i2c_writereg(CDNS_I2C_IXR_SLAVE_INTR_MASK,
280 				  CDNS_I2C_IER_OFFSET);
281 		break;
282 	}
283 }
284 
285 static void cdns_i2c_slave_rcv_data(struct cdns_i2c *id)
286 {
287 	u8 bytes;
288 	unsigned char data;
289 
290 	/* Prepare backend for data reception */
291 	if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
292 		id->slave_state = CDNS_I2C_SLAVE_STATE_RECV;
293 		i2c_slave_event(id->slave, I2C_SLAVE_WRITE_REQUESTED, NULL);
294 	}
295 
296 	/* Fetch number of bytes to receive */
297 	bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
298 
299 	/* Read data and send to backend */
300 	while (bytes--) {
301 		data = cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
302 		i2c_slave_event(id->slave, I2C_SLAVE_WRITE_RECEIVED, &data);
303 	}
304 }
305 
306 static void cdns_i2c_slave_send_data(struct cdns_i2c *id)
307 {
308 	u8 data;
309 
310 	/* Prepare backend for data transmission */
311 	if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
312 		id->slave_state = CDNS_I2C_SLAVE_STATE_SEND;
313 		i2c_slave_event(id->slave, I2C_SLAVE_READ_REQUESTED, &data);
314 	} else {
315 		i2c_slave_event(id->slave, I2C_SLAVE_READ_PROCESSED, &data);
316 	}
317 
318 	/* Send data over bus */
319 	cdns_i2c_writereg(data, CDNS_I2C_DATA_OFFSET);
320 }
321 
322 /**
323  * cdns_i2c_slave_isr - Interrupt handler for the I2C device in slave role
324  * @ptr:       Pointer to I2C device private data
325  *
326  * This function handles the data interrupt and transfer complete interrupt of
327  * the I2C device in slave role.
328  *
329  * Return: IRQ_HANDLED always
330  */
331 static irqreturn_t cdns_i2c_slave_isr(void *ptr)
332 {
333 	struct cdns_i2c *id = ptr;
334 	unsigned int isr_status, i2c_status;
335 
336 	/* Fetch the interrupt status */
337 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
338 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
339 
340 	/* Ignore masked interrupts */
341 	isr_status &= ~cdns_i2c_readreg(CDNS_I2C_IMR_OFFSET);
342 
343 	/* Fetch transfer mode (send/receive) */
344 	i2c_status = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
345 
346 	/* Handle data send/receive */
347 	if (i2c_status & CDNS_I2C_SR_RXRW) {
348 		/* Send data to master */
349 		if (isr_status & CDNS_I2C_IXR_DATA)
350 			cdns_i2c_slave_send_data(id);
351 
352 		if (isr_status & CDNS_I2C_IXR_COMP) {
353 			id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
354 			i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
355 		}
356 	} else {
357 		/* Receive data from master */
358 		if (isr_status & CDNS_I2C_IXR_DATA)
359 			cdns_i2c_slave_rcv_data(id);
360 
361 		if (isr_status & CDNS_I2C_IXR_COMP) {
362 			cdns_i2c_slave_rcv_data(id);
363 			id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
364 			i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
365 		}
366 	}
367 
368 	/* Master indicated xfer stop or fifo underflow/overflow */
369 	if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_RX_OVF |
370 			  CDNS_I2C_IXR_RX_UNF | CDNS_I2C_IXR_TX_OVF)) {
371 		id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
372 		i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
373 		cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
374 	}
375 
376 	return IRQ_HANDLED;
377 }
378 #endif
379 
380 /**
381  * cdns_i2c_master_isr - Interrupt handler for the I2C device in master role
382  * @ptr:       Pointer to I2C device private data
383  *
384  * This function handles the data interrupt, transfer complete interrupt and
385  * the error interrupts of the I2C device in master role.
386  *
387  * Return: IRQ_HANDLED always
388  */
389 static irqreturn_t cdns_i2c_master_isr(void *ptr)
390 {
391 	unsigned int isr_status, avail_bytes, updatetx;
392 	unsigned int bytes_to_send;
393 	bool hold_quirk;
394 	struct cdns_i2c *id = ptr;
395 	/* Signal completion only after everything is updated */
396 	int done_flag = 0;
397 	irqreturn_t status = IRQ_NONE;
398 
399 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
400 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
401 	id->err_status = 0;
402 
403 	/* Handling nack and arbitration lost interrupt */
404 	if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) {
405 		done_flag = 1;
406 		status = IRQ_HANDLED;
407 	}
408 
409 	/*
410 	 * Check if transfer size register needs to be updated again for a
411 	 * large data receive operation.
412 	 */
413 	updatetx = 0;
414 	if (id->recv_count > id->curr_recv_count)
415 		updatetx = 1;
416 
417 	hold_quirk = (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT) && updatetx;
418 
419 	/* When receiving, handle data interrupt and completion interrupt */
420 	if (id->p_recv_buf &&
421 	    ((isr_status & CDNS_I2C_IXR_COMP) ||
422 	     (isr_status & CDNS_I2C_IXR_DATA))) {
423 		/* Read data if receive data valid is set */
424 		while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
425 		       CDNS_I2C_SR_RXDV) {
426 			if (id->recv_count > 0) {
427 				*(id->p_recv_buf)++ =
428 					cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
429 				id->recv_count--;
430 				id->curr_recv_count--;
431 
432 				/*
433 				 * Clear hold bit that was set for FIFO control
434 				 * if RX data left is less than or equal to
435 				 * FIFO DEPTH unless repeated start is selected
436 				 */
437 				if (id->recv_count <= CDNS_I2C_FIFO_DEPTH &&
438 				    !id->bus_hold_flag)
439 					cdns_i2c_clear_bus_hold(id);
440 
441 			} else {
442 				dev_err(id->adap.dev.parent,
443 					"xfer_size reg rollover. xfer aborted!\n");
444 				id->err_status |= CDNS_I2C_IXR_TO;
445 				break;
446 			}
447 
448 			if (cdns_is_holdquirk(id, hold_quirk))
449 				break;
450 		}
451 
452 		/*
453 		 * The controller sends NACK to the slave when transfer size
454 		 * register reaches zero without considering the HOLD bit.
455 		 * This workaround is implemented for large data transfers to
456 		 * maintain transfer size non-zero while performing a large
457 		 * receive operation.
458 		 */
459 		if (cdns_is_holdquirk(id, hold_quirk)) {
460 			/* wait while fifo is full */
461 			while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) !=
462 			       (id->curr_recv_count - CDNS_I2C_FIFO_DEPTH))
463 				;
464 
465 			/*
466 			 * Check number of bytes to be received against maximum
467 			 * transfer size and update register accordingly.
468 			 */
469 			if (((int)(id->recv_count) - CDNS_I2C_FIFO_DEPTH) >
470 			    CDNS_I2C_TRANSFER_SIZE) {
471 				cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
472 						  CDNS_I2C_XFER_SIZE_OFFSET);
473 				id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE +
474 						      CDNS_I2C_FIFO_DEPTH;
475 			} else {
476 				cdns_i2c_writereg(id->recv_count -
477 						  CDNS_I2C_FIFO_DEPTH,
478 						  CDNS_I2C_XFER_SIZE_OFFSET);
479 				id->curr_recv_count = id->recv_count;
480 			}
481 		} else if (id->recv_count && !hold_quirk &&
482 						!id->curr_recv_count) {
483 
484 			/* Set the slave address in address register*/
485 			cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
486 						CDNS_I2C_ADDR_OFFSET);
487 
488 			if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
489 				cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
490 						CDNS_I2C_XFER_SIZE_OFFSET);
491 				id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
492 			} else {
493 				cdns_i2c_writereg(id->recv_count,
494 						CDNS_I2C_XFER_SIZE_OFFSET);
495 				id->curr_recv_count = id->recv_count;
496 			}
497 		}
498 
499 		/* Clear hold (if not repeated start) and signal completion */
500 		if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) {
501 			if (!id->bus_hold_flag)
502 				cdns_i2c_clear_bus_hold(id);
503 			done_flag = 1;
504 		}
505 
506 		status = IRQ_HANDLED;
507 	}
508 
509 	/* When sending, handle transfer complete interrupt */
510 	if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) {
511 		/*
512 		 * If there is more data to be sent, calculate the
513 		 * space available in FIFO and fill with that many bytes.
514 		 */
515 		if (id->send_count) {
516 			avail_bytes = CDNS_I2C_FIFO_DEPTH -
517 			    cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
518 			if (id->send_count > avail_bytes)
519 				bytes_to_send = avail_bytes;
520 			else
521 				bytes_to_send = id->send_count;
522 
523 			while (bytes_to_send--) {
524 				cdns_i2c_writereg(
525 					(*(id->p_send_buf)++),
526 					 CDNS_I2C_DATA_OFFSET);
527 				id->send_count--;
528 			}
529 		} else {
530 			/*
531 			 * Signal the completion of transaction and
532 			 * clear the hold bus bit if there are no
533 			 * further messages to be processed.
534 			 */
535 			done_flag = 1;
536 		}
537 		if (!id->send_count && !id->bus_hold_flag)
538 			cdns_i2c_clear_bus_hold(id);
539 
540 		status = IRQ_HANDLED;
541 	}
542 
543 	/* Update the status for errors */
544 	id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK;
545 	if (id->err_status)
546 		status = IRQ_HANDLED;
547 
548 	if (done_flag)
549 		complete(&id->xfer_done);
550 
551 	return status;
552 }
553 
554 /**
555  * cdns_i2c_isr - Interrupt handler for the I2C device
556  * @irq:	irq number for the I2C device
557  * @ptr:	void pointer to cdns_i2c structure
558  *
559  * This function passes the control to slave/master based on current role of
560  * i2c controller.
561  *
562  * Return: IRQ_HANDLED always
563  */
564 static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
565 {
566 #if IS_ENABLED(CONFIG_I2C_SLAVE)
567 	struct cdns_i2c *id = ptr;
568 
569 	if (id->dev_mode == CDNS_I2C_MODE_SLAVE)
570 		return cdns_i2c_slave_isr(ptr);
571 #endif
572 	return cdns_i2c_master_isr(ptr);
573 }
574 
575 /**
576  * cdns_i2c_mrecv - Prepare and start a master receive operation
577  * @id:		pointer to the i2c device structure
578  */
579 static void cdns_i2c_mrecv(struct cdns_i2c *id)
580 {
581 	unsigned int ctrl_reg;
582 	unsigned int isr_status;
583 	unsigned long flags;
584 	bool hold_clear = false;
585 	bool irq_save = false;
586 
587 	u32 addr;
588 
589 	id->p_recv_buf = id->p_msg->buf;
590 	id->recv_count = id->p_msg->len;
591 
592 	/* Put the controller in master receive mode and clear the FIFO */
593 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
594 	ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO;
595 
596 	if (id->p_msg->flags & I2C_M_RECV_LEN)
597 		id->recv_count = I2C_SMBUS_BLOCK_MAX + 1;
598 
599 	id->curr_recv_count = id->recv_count;
600 
601 	/*
602 	 * Check for the message size against FIFO depth and set the
603 	 * 'hold bus' bit if it is greater than FIFO depth.
604 	 */
605 	if (id->recv_count > CDNS_I2C_FIFO_DEPTH)
606 		ctrl_reg |= CDNS_I2C_CR_HOLD;
607 
608 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
609 
610 	/* Clear the interrupts in interrupt status register */
611 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
612 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
613 
614 	/*
615 	 * The no. of bytes to receive is checked against the limit of
616 	 * max transfer size. Set transfer size register with no of bytes
617 	 * receive if it is less than transfer size and transfer size if
618 	 * it is more. Enable the interrupts.
619 	 */
620 	if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
621 		cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
622 				  CDNS_I2C_XFER_SIZE_OFFSET);
623 		id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
624 	} else {
625 		cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET);
626 	}
627 
628 	/* Determine hold_clear based on number of bytes to receive and hold flag */
629 	if (!id->bus_hold_flag &&
630 	    ((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
631 	    (id->recv_count <= CDNS_I2C_FIFO_DEPTH)) {
632 		if (cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & CDNS_I2C_CR_HOLD) {
633 			hold_clear = true;
634 			if (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT)
635 				irq_save = true;
636 		}
637 	}
638 
639 	addr = id->p_msg->addr;
640 	addr &= CDNS_I2C_ADDR_MASK;
641 
642 	if (hold_clear) {
643 		ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & ~CDNS_I2C_CR_HOLD;
644 		/*
645 		 * In case of Xilinx Zynq SOC, clear the HOLD bit before transfer size
646 		 * register reaches '0'. This is an IP bug which causes transfer size
647 		 * register overflow to 0xFF. To satisfy this timing requirement,
648 		 * disable the interrupts on current processor core between register
649 		 * writes to slave address register and control register.
650 		 */
651 		if (irq_save)
652 			local_irq_save(flags);
653 
654 		cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
655 		cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
656 		/* Read it back to avoid bufferring and make sure write happens */
657 		cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
658 
659 		if (irq_save)
660 			local_irq_restore(flags);
661 	} else {
662 		cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
663 	}
664 
665 	cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
666 }
667 
668 /**
669  * cdns_i2c_msend - Prepare and start a master send operation
670  * @id:		pointer to the i2c device
671  */
672 static void cdns_i2c_msend(struct cdns_i2c *id)
673 {
674 	unsigned int avail_bytes;
675 	unsigned int bytes_to_send;
676 	unsigned int ctrl_reg;
677 	unsigned int isr_status;
678 
679 	id->p_recv_buf = NULL;
680 	id->p_send_buf = id->p_msg->buf;
681 	id->send_count = id->p_msg->len;
682 
683 	/* Set the controller in Master transmit mode and clear the FIFO. */
684 	ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
685 	ctrl_reg &= ~CDNS_I2C_CR_RW;
686 	ctrl_reg |= CDNS_I2C_CR_CLR_FIFO;
687 
688 	/*
689 	 * Check for the message size against FIFO depth and set the
690 	 * 'hold bus' bit if it is greater than FIFO depth.
691 	 */
692 	if (id->send_count > CDNS_I2C_FIFO_DEPTH)
693 		ctrl_reg |= CDNS_I2C_CR_HOLD;
694 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
695 
696 	/* Clear the interrupts in interrupt status register. */
697 	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
698 	cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
699 
700 	/*
701 	 * Calculate the space available in FIFO. Check the message length
702 	 * against the space available, and fill the FIFO accordingly.
703 	 * Enable the interrupts.
704 	 */
705 	avail_bytes = CDNS_I2C_FIFO_DEPTH -
706 				cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
707 
708 	if (id->send_count > avail_bytes)
709 		bytes_to_send = avail_bytes;
710 	else
711 		bytes_to_send = id->send_count;
712 
713 	while (bytes_to_send--) {
714 		cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET);
715 		id->send_count--;
716 	}
717 
718 	/*
719 	 * Clear the bus hold flag if there is no more data
720 	 * and if it is the last message.
721 	 */
722 	if (!id->bus_hold_flag && !id->send_count)
723 		cdns_i2c_clear_bus_hold(id);
724 	/* Set the slave address in address register - triggers operation. */
725 	cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
726 						CDNS_I2C_ADDR_OFFSET);
727 
728 	cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
729 }
730 
731 /**
732  * cdns_i2c_master_reset - Reset the interface
733  * @adap:	pointer to the i2c adapter driver instance
734  *
735  * This function cleanup the fifos, clear the hold bit and status
736  * and disable the interrupts.
737  */
738 static void cdns_i2c_master_reset(struct i2c_adapter *adap)
739 {
740 	struct cdns_i2c *id = adap->algo_data;
741 	u32 regval;
742 
743 	/* Disable the interrupts */
744 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
745 	/* Clear the hold bit and fifos */
746 	regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
747 	regval &= ~CDNS_I2C_CR_HOLD;
748 	regval |= CDNS_I2C_CR_CLR_FIFO;
749 	cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET);
750 	/* Update the transfercount register to zero */
751 	cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET);
752 	/* Clear the interrupt status register */
753 	regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
754 	cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET);
755 	/* Clear the status register */
756 	regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
757 	cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET);
758 }
759 
760 static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg,
761 		struct i2c_adapter *adap)
762 {
763 	unsigned long time_left, msg_timeout;
764 	u32 reg;
765 
766 	id->p_msg = msg;
767 	id->err_status = 0;
768 	reinit_completion(&id->xfer_done);
769 
770 	/* Check for the TEN Bit mode on each msg */
771 	reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
772 	if (msg->flags & I2C_M_TEN) {
773 		if (reg & CDNS_I2C_CR_NEA)
774 			cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA,
775 					CDNS_I2C_CR_OFFSET);
776 	} else {
777 		if (!(reg & CDNS_I2C_CR_NEA))
778 			cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA,
779 					CDNS_I2C_CR_OFFSET);
780 	}
781 
782 	/* Check for the R/W flag on each msg */
783 	if (msg->flags & I2C_M_RD)
784 		cdns_i2c_mrecv(id);
785 	else
786 		cdns_i2c_msend(id);
787 
788 	/* Minimal time to execute this message */
789 	msg_timeout = msecs_to_jiffies((1000 * msg->len * BITS_PER_BYTE) / id->i2c_clk);
790 	/* Plus some wiggle room */
791 	msg_timeout += msecs_to_jiffies(500);
792 
793 	if (msg_timeout < adap->timeout)
794 		msg_timeout = adap->timeout;
795 
796 	/* Wait for the signal of completion */
797 	time_left = wait_for_completion_timeout(&id->xfer_done, msg_timeout);
798 	if (time_left == 0) {
799 		cdns_i2c_master_reset(adap);
800 		dev_err(id->adap.dev.parent,
801 				"timeout waiting on completion\n");
802 		return -ETIMEDOUT;
803 	}
804 
805 	cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK,
806 			  CDNS_I2C_IDR_OFFSET);
807 
808 	/* If it is bus arbitration error, try again */
809 	if (id->err_status & CDNS_I2C_IXR_ARB_LOST)
810 		return -EAGAIN;
811 
812 	return 0;
813 }
814 
815 /**
816  * cdns_i2c_master_xfer - The main i2c transfer function
817  * @adap:	pointer to the i2c adapter driver instance
818  * @msgs:	pointer to the i2c message structure
819  * @num:	the number of messages to transfer
820  *
821  * Initiates the send/recv activity based on the transfer message received.
822  *
823  * Return: number of msgs processed on success, negative error otherwise
824  */
825 static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
826 				int num)
827 {
828 	int ret, count;
829 	u32 reg;
830 	struct cdns_i2c *id = adap->algo_data;
831 	bool hold_quirk;
832 #if IS_ENABLED(CONFIG_I2C_SLAVE)
833 	bool change_role = false;
834 #endif
835 
836 	ret = pm_runtime_resume_and_get(id->dev);
837 	if (ret < 0)
838 		return ret;
839 
840 #if IS_ENABLED(CONFIG_I2C_SLAVE)
841 	/* Check i2c operating mode and switch if possible */
842 	if (id->dev_mode == CDNS_I2C_MODE_SLAVE) {
843 		if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE)
844 			return -EAGAIN;
845 
846 		/* Set mode to master */
847 		cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
848 
849 		/* Mark flag to change role once xfer is completed */
850 		change_role = true;
851 	}
852 #endif
853 
854 	/* Check if the bus is free */
855 	if (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) & CDNS_I2C_SR_BA) {
856 		ret = -EAGAIN;
857 		goto out;
858 	}
859 
860 	hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT);
861 	/*
862 	 * Set the flag to one when multiple messages are to be
863 	 * processed with a repeated start.
864 	 */
865 	if (num > 1) {
866 		/*
867 		 * This controller does not give completion interrupt after a
868 		 * master receive message if HOLD bit is set (repeated start),
869 		 * resulting in SW timeout. Hence, if a receive message is
870 		 * followed by any other message, an error is returned
871 		 * indicating that this sequence is not supported.
872 		 */
873 		for (count = 0; (count < num - 1 && hold_quirk); count++) {
874 			if (msgs[count].flags & I2C_M_RD) {
875 				dev_warn(adap->dev.parent,
876 					 "Can't do repeated start after a receive message\n");
877 				ret = -EOPNOTSUPP;
878 				goto out;
879 			}
880 		}
881 		id->bus_hold_flag = 1;
882 		reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
883 		reg |= CDNS_I2C_CR_HOLD;
884 		cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET);
885 	} else {
886 		id->bus_hold_flag = 0;
887 	}
888 
889 	/* Process the msg one by one */
890 	for (count = 0; count < num; count++, msgs++) {
891 		if (count == (num - 1))
892 			id->bus_hold_flag = 0;
893 
894 		ret = cdns_i2c_process_msg(id, msgs, adap);
895 		if (ret)
896 			goto out;
897 
898 		/* Report the other error interrupts to application */
899 		if (id->err_status) {
900 			cdns_i2c_master_reset(adap);
901 
902 			if (id->err_status & CDNS_I2C_IXR_NACK) {
903 				ret = -ENXIO;
904 				goto out;
905 			}
906 			ret = -EIO;
907 			goto out;
908 		}
909 	}
910 
911 	ret = num;
912 
913 out:
914 
915 #if IS_ENABLED(CONFIG_I2C_SLAVE)
916 	/* Switch i2c mode to slave */
917 	if (change_role)
918 		cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
919 #endif
920 
921 	pm_runtime_mark_last_busy(id->dev);
922 	pm_runtime_put_autosuspend(id->dev);
923 	return ret;
924 }
925 
926 /**
927  * cdns_i2c_func - Returns the supported features of the I2C driver
928  * @adap:	pointer to the i2c adapter structure
929  *
930  * Return: 32 bit value, each bit corresponding to a feature
931  */
932 static u32 cdns_i2c_func(struct i2c_adapter *adap)
933 {
934 	u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR |
935 			(I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
936 			I2C_FUNC_SMBUS_BLOCK_DATA;
937 
938 #if IS_ENABLED(CONFIG_I2C_SLAVE)
939 	func |= I2C_FUNC_SLAVE;
940 #endif
941 
942 	return func;
943 }
944 
945 #if IS_ENABLED(CONFIG_I2C_SLAVE)
946 static int cdns_reg_slave(struct i2c_client *slave)
947 {
948 	int ret;
949 	struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
950 									adap);
951 
952 	if (id->slave)
953 		return -EBUSY;
954 
955 	if (slave->flags & I2C_CLIENT_TEN)
956 		return -EAFNOSUPPORT;
957 
958 	ret = pm_runtime_resume_and_get(id->dev);
959 	if (ret < 0)
960 		return ret;
961 
962 	/* Store slave information */
963 	id->slave = slave;
964 
965 	/* Enable I2C slave */
966 	cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
967 
968 	return 0;
969 }
970 
971 static int cdns_unreg_slave(struct i2c_client *slave)
972 {
973 	struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
974 									adap);
975 
976 	pm_runtime_put(id->dev);
977 
978 	/* Remove slave information */
979 	id->slave = NULL;
980 
981 	/* Enable I2C master */
982 	cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
983 
984 	return 0;
985 }
986 #endif
987 
988 static const struct i2c_algorithm cdns_i2c_algo = {
989 	.master_xfer	= cdns_i2c_master_xfer,
990 	.functionality	= cdns_i2c_func,
991 #if IS_ENABLED(CONFIG_I2C_SLAVE)
992 	.reg_slave	= cdns_reg_slave,
993 	.unreg_slave	= cdns_unreg_slave,
994 #endif
995 };
996 
997 /**
998  * cdns_i2c_calc_divs - Calculate clock dividers
999  * @f:		I2C clock frequency
1000  * @input_clk:	Input clock frequency
1001  * @a:		First divider (return value)
1002  * @b:		Second divider (return value)
1003  *
1004  * f is used as input and output variable. As input it is used as target I2C
1005  * frequency. On function exit f holds the actually resulting I2C frequency.
1006  *
1007  * Return: 0 on success, negative errno otherwise.
1008  */
1009 static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk,
1010 		unsigned int *a, unsigned int *b)
1011 {
1012 	unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp;
1013 	unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0;
1014 	unsigned int last_error, current_error;
1015 
1016 	/* calculate (divisor_a+1) x (divisor_b+1) */
1017 	temp = input_clk / (22 * fscl);
1018 
1019 	/*
1020 	 * If the calculated value is negative or 0, the fscl input is out of
1021 	 * range. Return error.
1022 	 */
1023 	if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX)))
1024 		return -EINVAL;
1025 
1026 	last_error = -1;
1027 	for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) {
1028 		div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1));
1029 
1030 		if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX))
1031 			continue;
1032 		div_b--;
1033 
1034 		actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1));
1035 
1036 		if (actual_fscl > fscl)
1037 			continue;
1038 
1039 		current_error = ((actual_fscl > fscl) ? (actual_fscl - fscl) :
1040 							(fscl - actual_fscl));
1041 
1042 		if (last_error > current_error) {
1043 			calc_div_a = div_a;
1044 			calc_div_b = div_b;
1045 			best_fscl = actual_fscl;
1046 			last_error = current_error;
1047 		}
1048 	}
1049 
1050 	*a = calc_div_a;
1051 	*b = calc_div_b;
1052 	*f = best_fscl;
1053 
1054 	return 0;
1055 }
1056 
1057 /**
1058  * cdns_i2c_setclk - This function sets the serial clock rate for the I2C device
1059  * @clk_in:	I2C clock input frequency in Hz
1060  * @id:		Pointer to the I2C device structure
1061  *
1062  * The device must be idle rather than busy transferring data before setting
1063  * these device options.
1064  * The data rate is set by values in the control register.
1065  * The formula for determining the correct register values is
1066  *	Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1))
1067  * See the hardware data sheet for a full explanation of setting the serial
1068  * clock rate. The clock can not be faster than the input clock divide by 22.
1069  * The two most common clock rates are 100KHz and 400KHz.
1070  *
1071  * Return: 0 on success, negative error otherwise
1072  */
1073 static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id)
1074 {
1075 	unsigned int div_a, div_b;
1076 	unsigned int ctrl_reg;
1077 	int ret = 0;
1078 	unsigned long fscl = id->i2c_clk;
1079 
1080 	ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b);
1081 	if (ret)
1082 		return ret;
1083 
1084 	ctrl_reg = id->ctrl_reg;
1085 	ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK);
1086 	ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) |
1087 			(div_b << CDNS_I2C_CR_DIVB_SHIFT));
1088 	id->ctrl_reg = ctrl_reg;
1089 	cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
1090 #if IS_ENABLED(CONFIG_I2C_SLAVE)
1091 	id->ctrl_reg_diva_divb = ctrl_reg & (CDNS_I2C_CR_DIVA_MASK |
1092 				 CDNS_I2C_CR_DIVB_MASK);
1093 #endif
1094 	return 0;
1095 }
1096 
1097 /**
1098  * cdns_i2c_clk_notifier_cb - Clock rate change callback
1099  * @nb:		Pointer to notifier block
1100  * @event:	Notification reason
1101  * @data:	Pointer to notification data object
1102  *
1103  * This function is called when the cdns_i2c input clock frequency changes.
1104  * The callback checks whether a valid bus frequency can be generated after the
1105  * change. If so, the change is acknowledged, otherwise the change is aborted.
1106  * New dividers are written to the HW in the pre- or post change notification
1107  * depending on the scaling direction.
1108  *
1109  * Return:	NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
1110  *		to acknowledge the change, NOTIFY_DONE if the notification is
1111  *		considered irrelevant.
1112  */
1113 static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
1114 		event, void *data)
1115 {
1116 	struct clk_notifier_data *ndata = data;
1117 	struct cdns_i2c *id = to_cdns_i2c(nb);
1118 
1119 	if (pm_runtime_suspended(id->dev))
1120 		return NOTIFY_OK;
1121 
1122 	switch (event) {
1123 	case PRE_RATE_CHANGE:
1124 	{
1125 		unsigned long input_clk = ndata->new_rate;
1126 		unsigned long fscl = id->i2c_clk;
1127 		unsigned int div_a, div_b;
1128 		int ret;
1129 
1130 		ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b);
1131 		if (ret) {
1132 			dev_warn(id->adap.dev.parent,
1133 					"clock rate change rejected\n");
1134 			return NOTIFY_STOP;
1135 		}
1136 
1137 		/* scale up */
1138 		if (ndata->new_rate > ndata->old_rate)
1139 			cdns_i2c_setclk(ndata->new_rate, id);
1140 
1141 		return NOTIFY_OK;
1142 	}
1143 	case POST_RATE_CHANGE:
1144 		id->input_clk = ndata->new_rate;
1145 		/* scale down */
1146 		if (ndata->new_rate < ndata->old_rate)
1147 			cdns_i2c_setclk(ndata->new_rate, id);
1148 		return NOTIFY_OK;
1149 	case ABORT_RATE_CHANGE:
1150 		/* scale up */
1151 		if (ndata->new_rate > ndata->old_rate)
1152 			cdns_i2c_setclk(ndata->old_rate, id);
1153 		return NOTIFY_OK;
1154 	default:
1155 		return NOTIFY_DONE;
1156 	}
1157 }
1158 
1159 /**
1160  * cdns_i2c_runtime_suspend -  Runtime suspend method for the driver
1161  * @dev:	Address of the platform_device structure
1162  *
1163  * Put the driver into low power mode.
1164  *
1165  * Return: 0 always
1166  */
1167 static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev)
1168 {
1169 	struct cdns_i2c *xi2c = dev_get_drvdata(dev);
1170 
1171 	clk_disable(xi2c->clk);
1172 
1173 	return 0;
1174 }
1175 
1176 /**
1177  * cdns_i2c_init -  Controller initialisation
1178  * @id:		Device private data structure
1179  *
1180  * Initialise the i2c controller.
1181  *
1182  */
1183 static void cdns_i2c_init(struct cdns_i2c *id)
1184 {
1185 	cdns_i2c_writereg(id->ctrl_reg, CDNS_I2C_CR_OFFSET);
1186 	/*
1187 	 * Cadence I2C controller has a bug wherein it generates
1188 	 * invalid read transaction after HW timeout in master receiver mode.
1189 	 * HW timeout is not used by this driver and the interrupt is disabled.
1190 	 * But the feature itself cannot be disabled. Hence maximum value
1191 	 * is written to this register to reduce the chances of error.
1192 	 */
1193 	cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET);
1194 }
1195 
1196 /**
1197  * cdns_i2c_runtime_resume - Runtime resume
1198  * @dev:	Address of the platform_device structure
1199  *
1200  * Runtime resume callback.
1201  *
1202  * Return: 0 on success and error value on error
1203  */
1204 static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev)
1205 {
1206 	struct cdns_i2c *xi2c = dev_get_drvdata(dev);
1207 	int ret;
1208 
1209 	ret = clk_enable(xi2c->clk);
1210 	if (ret) {
1211 		dev_err(dev, "Cannot enable clock.\n");
1212 		return ret;
1213 	}
1214 	cdns_i2c_init(xi2c);
1215 
1216 	return 0;
1217 }
1218 
1219 static const struct dev_pm_ops cdns_i2c_dev_pm_ops = {
1220 	SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend,
1221 			   cdns_i2c_runtime_resume, NULL)
1222 };
1223 
1224 static const struct cdns_platform_data r1p10_i2c_def = {
1225 	.quirks = CDNS_I2C_BROKEN_HOLD_BIT,
1226 };
1227 
1228 static const struct of_device_id cdns_i2c_of_match[] = {
1229 	{ .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def },
1230 	{ .compatible = "cdns,i2c-r1p14",},
1231 	{ /* end of table */ }
1232 };
1233 MODULE_DEVICE_TABLE(of, cdns_i2c_of_match);
1234 
1235 /**
1236  * cdns_i2c_probe - Platform registration call
1237  * @pdev:	Handle to the platform device structure
1238  *
1239  * This function does all the memory allocation and registration for the i2c
1240  * device. User can modify the address mode to 10 bit address mode using the
1241  * ioctl call with option I2C_TENBIT.
1242  *
1243  * Return: 0 on success, negative error otherwise
1244  */
1245 static int cdns_i2c_probe(struct platform_device *pdev)
1246 {
1247 	struct resource *r_mem;
1248 	struct cdns_i2c *id;
1249 	int ret;
1250 	const struct of_device_id *match;
1251 
1252 	id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL);
1253 	if (!id)
1254 		return -ENOMEM;
1255 
1256 	id->dev = &pdev->dev;
1257 	platform_set_drvdata(pdev, id);
1258 
1259 	match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node);
1260 	if (match && match->data) {
1261 		const struct cdns_platform_data *data = match->data;
1262 		id->quirks = data->quirks;
1263 	}
1264 
1265 	id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem);
1266 	if (IS_ERR(id->membase))
1267 		return PTR_ERR(id->membase);
1268 
1269 	ret = platform_get_irq(pdev, 0);
1270 	if (ret < 0)
1271 		return ret;
1272 	id->irq = ret;
1273 
1274 	id->adap.owner = THIS_MODULE;
1275 	id->adap.dev.of_node = pdev->dev.of_node;
1276 	id->adap.algo = &cdns_i2c_algo;
1277 	id->adap.timeout = CDNS_I2C_TIMEOUT;
1278 	id->adap.retries = 3;		/* Default retry value. */
1279 	id->adap.algo_data = id;
1280 	id->adap.dev.parent = &pdev->dev;
1281 	init_completion(&id->xfer_done);
1282 	snprintf(id->adap.name, sizeof(id->adap.name),
1283 		 "Cadence I2C at %08lx", (unsigned long)r_mem->start);
1284 
1285 	id->clk = devm_clk_get(&pdev->dev, NULL);
1286 	if (IS_ERR(id->clk))
1287 		return dev_err_probe(&pdev->dev, PTR_ERR(id->clk),
1288 				     "input clock not found.\n");
1289 
1290 	ret = clk_prepare_enable(id->clk);
1291 	if (ret)
1292 		dev_err(&pdev->dev, "Unable to enable clock.\n");
1293 
1294 	pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT);
1295 	pm_runtime_use_autosuspend(id->dev);
1296 	pm_runtime_set_active(id->dev);
1297 	pm_runtime_enable(id->dev);
1298 
1299 	id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb;
1300 	if (clk_notifier_register(id->clk, &id->clk_rate_change_nb))
1301 		dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
1302 	id->input_clk = clk_get_rate(id->clk);
1303 
1304 	ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
1305 			&id->i2c_clk);
1306 	if (ret || (id->i2c_clk > I2C_MAX_FAST_MODE_FREQ))
1307 		id->i2c_clk = I2C_MAX_STANDARD_MODE_FREQ;
1308 
1309 #if IS_ENABLED(CONFIG_I2C_SLAVE)
1310 	/* Set initial mode to master */
1311 	id->dev_mode = CDNS_I2C_MODE_MASTER;
1312 	id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
1313 #endif
1314 	id->ctrl_reg = CDNS_I2C_CR_ACK_EN | CDNS_I2C_CR_NEA | CDNS_I2C_CR_MS;
1315 
1316 	ret = cdns_i2c_setclk(id->input_clk, id);
1317 	if (ret) {
1318 		dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk);
1319 		ret = -EINVAL;
1320 		goto err_clk_dis;
1321 	}
1322 
1323 	ret = devm_request_irq(&pdev->dev, id->irq, cdns_i2c_isr, 0,
1324 				 DRIVER_NAME, id);
1325 	if (ret) {
1326 		dev_err(&pdev->dev, "cannot get irq %d\n", id->irq);
1327 		goto err_clk_dis;
1328 	}
1329 	cdns_i2c_init(id);
1330 
1331 	ret = i2c_add_adapter(&id->adap);
1332 	if (ret < 0)
1333 		goto err_clk_dis;
1334 
1335 	dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n",
1336 		 id->i2c_clk / 1000, (unsigned long)r_mem->start, id->irq);
1337 
1338 	return 0;
1339 
1340 err_clk_dis:
1341 	clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
1342 	clk_disable_unprepare(id->clk);
1343 	pm_runtime_disable(&pdev->dev);
1344 	pm_runtime_set_suspended(&pdev->dev);
1345 	return ret;
1346 }
1347 
1348 /**
1349  * cdns_i2c_remove - Unregister the device after releasing the resources
1350  * @pdev:	Handle to the platform device structure
1351  *
1352  * This function frees all the resources allocated to the device.
1353  *
1354  * Return: 0 always
1355  */
1356 static int cdns_i2c_remove(struct platform_device *pdev)
1357 {
1358 	struct cdns_i2c *id = platform_get_drvdata(pdev);
1359 
1360 	pm_runtime_disable(&pdev->dev);
1361 	pm_runtime_set_suspended(&pdev->dev);
1362 	pm_runtime_dont_use_autosuspend(&pdev->dev);
1363 
1364 	i2c_del_adapter(&id->adap);
1365 	clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
1366 	clk_disable_unprepare(id->clk);
1367 
1368 	return 0;
1369 }
1370 
1371 static struct platform_driver cdns_i2c_drv = {
1372 	.driver = {
1373 		.name  = DRIVER_NAME,
1374 		.of_match_table = cdns_i2c_of_match,
1375 		.pm = &cdns_i2c_dev_pm_ops,
1376 	},
1377 	.probe  = cdns_i2c_probe,
1378 	.remove = cdns_i2c_remove,
1379 };
1380 
1381 module_platform_driver(cdns_i2c_drv);
1382 
1383 MODULE_AUTHOR("Xilinx Inc.");
1384 MODULE_DESCRIPTION("Cadence I2C bus driver");
1385 MODULE_LICENSE("GPL");
1386