1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * i2c Support for Atmel's AT91 Two-Wire Interface (TWI) 4 * 5 * Copyright (C) 2011 Weinmann Medical GmbH 6 * Author: Nikolaus Voss <n.voss@weinmann.de> 7 * 8 * Evolved from original work by: 9 * Copyright (C) 2004 Rick Bronson 10 * Converted to 2.6 by Andrew Victor <andrew@sanpeople.com> 11 * 12 * Borrowed heavily from original work by: 13 * Copyright (C) 2000 Philip Edelbrock <phil@stimpy.netroedge.com> 14 */ 15 16 #include <linux/clk.h> 17 #include <linux/completion.h> 18 #include <linux/dma-mapping.h> 19 #include <linux/dmaengine.h> 20 #include <linux/err.h> 21 #include <linux/gpio/consumer.h> 22 #include <linux/i2c.h> 23 #include <linux/interrupt.h> 24 #include <linux/io.h> 25 #include <linux/of.h> 26 #include <linux/of_device.h> 27 #include <linux/pinctrl/consumer.h> 28 #include <linux/platform_device.h> 29 #include <linux/platform_data/dma-atmel.h> 30 #include <linux/pm_runtime.h> 31 32 #include "i2c-at91.h" 33 34 void at91_init_twi_bus_master(struct at91_twi_dev *dev) 35 { 36 struct at91_twi_pdata *pdata = dev->pdata; 37 u32 filtr = 0; 38 39 /* FIFO should be enabled immediately after the software reset */ 40 if (dev->fifo_size) 41 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_FIFOEN); 42 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_MSEN); 43 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_SVDIS); 44 at91_twi_write(dev, AT91_TWI_CWGR, dev->twi_cwgr_reg); 45 46 /* enable digital filter */ 47 if (pdata->has_dig_filtr && dev->enable_dig_filt) 48 filtr |= AT91_TWI_FILTR_FILT; 49 50 /* enable advanced digital filter */ 51 if (pdata->has_adv_dig_filtr && dev->enable_dig_filt) 52 filtr |= AT91_TWI_FILTR_FILT | 53 (AT91_TWI_FILTR_THRES(dev->filter_width) & 54 AT91_TWI_FILTR_THRES_MASK); 55 56 /* enable analog filter */ 57 if (pdata->has_ana_filtr && dev->enable_ana_filt) 58 filtr |= AT91_TWI_FILTR_PADFEN; 59 60 if (filtr) 61 at91_twi_write(dev, AT91_TWI_FILTR, filtr); 62 } 63 64 /* 65 * Calculate symmetric clock as stated in datasheet: 66 * twi_clk = F_MAIN / (2 * (cdiv * (1 << ckdiv) + offset)) 67 */ 68 static void at91_calc_twi_clock(struct at91_twi_dev *dev) 69 { 70 int ckdiv, cdiv, div, hold = 0, filter_width = 0; 71 struct at91_twi_pdata *pdata = dev->pdata; 72 int offset = pdata->clk_offset; 73 int max_ckdiv = pdata->clk_max_div; 74 struct i2c_timings timings, *t = &timings; 75 76 i2c_parse_fw_timings(dev->dev, t, true); 77 78 div = max(0, (int)DIV_ROUND_UP(clk_get_rate(dev->clk), 79 2 * t->bus_freq_hz) - offset); 80 ckdiv = fls(div >> 8); 81 cdiv = div >> ckdiv; 82 83 if (ckdiv > max_ckdiv) { 84 dev_warn(dev->dev, "%d exceeds ckdiv max value which is %d.\n", 85 ckdiv, max_ckdiv); 86 ckdiv = max_ckdiv; 87 cdiv = 255; 88 } 89 90 if (pdata->has_hold_field) { 91 /* 92 * hold time = HOLD + 3 x T_peripheral_clock 93 * Use clk rate in kHz to prevent overflows when computing 94 * hold. 95 */ 96 hold = DIV_ROUND_UP(t->sda_hold_ns 97 * (clk_get_rate(dev->clk) / 1000), 1000000); 98 hold -= 3; 99 if (hold < 0) 100 hold = 0; 101 if (hold > AT91_TWI_CWGR_HOLD_MAX) { 102 dev_warn(dev->dev, 103 "HOLD field set to its maximum value (%d instead of %d)\n", 104 AT91_TWI_CWGR_HOLD_MAX, hold); 105 hold = AT91_TWI_CWGR_HOLD_MAX; 106 } 107 } 108 109 if (pdata->has_adv_dig_filtr) { 110 /* 111 * filter width = 0 to AT91_TWI_FILTR_THRES_MAX 112 * peripheral clocks 113 */ 114 filter_width = DIV_ROUND_UP(t->digital_filter_width_ns 115 * (clk_get_rate(dev->clk) / 1000), 1000000); 116 if (filter_width > AT91_TWI_FILTR_THRES_MAX) { 117 dev_warn(dev->dev, 118 "Filter threshold set to its maximum value (%d instead of %d)\n", 119 AT91_TWI_FILTR_THRES_MAX, filter_width); 120 filter_width = AT91_TWI_FILTR_THRES_MAX; 121 } 122 } 123 124 dev->twi_cwgr_reg = (ckdiv << 16) | (cdiv << 8) | cdiv 125 | AT91_TWI_CWGR_HOLD(hold); 126 127 dev->filter_width = filter_width; 128 129 dev_dbg(dev->dev, "cdiv %d ckdiv %d hold %d (%d ns), filter_width %d (%d ns)\n", 130 cdiv, ckdiv, hold, t->sda_hold_ns, filter_width, 131 t->digital_filter_width_ns); 132 } 133 134 static void at91_twi_dma_cleanup(struct at91_twi_dev *dev) 135 { 136 struct at91_twi_dma *dma = &dev->dma; 137 138 at91_twi_irq_save(dev); 139 140 if (dma->xfer_in_progress) { 141 if (dma->direction == DMA_FROM_DEVICE) 142 dmaengine_terminate_all(dma->chan_rx); 143 else 144 dmaengine_terminate_all(dma->chan_tx); 145 dma->xfer_in_progress = false; 146 } 147 if (dma->buf_mapped) { 148 dma_unmap_single(dev->dev, sg_dma_address(&dma->sg[0]), 149 dev->buf_len, dma->direction); 150 dma->buf_mapped = false; 151 } 152 153 at91_twi_irq_restore(dev); 154 } 155 156 static void at91_twi_write_next_byte(struct at91_twi_dev *dev) 157 { 158 if (!dev->buf_len) 159 return; 160 161 /* 8bit write works with and without FIFO */ 162 writeb_relaxed(*dev->buf, dev->base + AT91_TWI_THR); 163 164 /* send stop when last byte has been written */ 165 if (--dev->buf_len == 0) { 166 if (!dev->use_alt_cmd) 167 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); 168 at91_twi_write(dev, AT91_TWI_IDR, AT91_TWI_TXRDY); 169 } 170 171 dev_dbg(dev->dev, "wrote 0x%x, to go %zu\n", *dev->buf, dev->buf_len); 172 173 ++dev->buf; 174 } 175 176 static void at91_twi_write_data_dma_callback(void *data) 177 { 178 struct at91_twi_dev *dev = (struct at91_twi_dev *)data; 179 180 dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg[0]), 181 dev->buf_len, DMA_TO_DEVICE); 182 183 /* 184 * When this callback is called, THR/TX FIFO is likely not to be empty 185 * yet. So we have to wait for TXCOMP or NACK bits to be set into the 186 * Status Register to be sure that the STOP bit has been sent and the 187 * transfer is completed. The NACK interrupt has already been enabled, 188 * we just have to enable TXCOMP one. 189 */ 190 at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); 191 if (!dev->use_alt_cmd) 192 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); 193 } 194 195 static void at91_twi_write_data_dma(struct at91_twi_dev *dev) 196 { 197 dma_addr_t dma_addr; 198 struct dma_async_tx_descriptor *txdesc; 199 struct at91_twi_dma *dma = &dev->dma; 200 struct dma_chan *chan_tx = dma->chan_tx; 201 unsigned int sg_len = 1; 202 203 if (!dev->buf_len) 204 return; 205 206 dma->direction = DMA_TO_DEVICE; 207 208 at91_twi_irq_save(dev); 209 dma_addr = dma_map_single(dev->dev, dev->buf, dev->buf_len, 210 DMA_TO_DEVICE); 211 if (dma_mapping_error(dev->dev, dma_addr)) { 212 dev_err(dev->dev, "dma map failed\n"); 213 return; 214 } 215 dma->buf_mapped = true; 216 at91_twi_irq_restore(dev); 217 218 if (dev->fifo_size) { 219 size_t part1_len, part2_len; 220 struct scatterlist *sg; 221 unsigned fifo_mr; 222 223 sg_len = 0; 224 225 part1_len = dev->buf_len & ~0x3; 226 if (part1_len) { 227 sg = &dma->sg[sg_len++]; 228 sg_dma_len(sg) = part1_len; 229 sg_dma_address(sg) = dma_addr; 230 } 231 232 part2_len = dev->buf_len & 0x3; 233 if (part2_len) { 234 sg = &dma->sg[sg_len++]; 235 sg_dma_len(sg) = part2_len; 236 sg_dma_address(sg) = dma_addr + part1_len; 237 } 238 239 /* 240 * DMA controller is triggered when at least 4 data can be 241 * written into the TX FIFO 242 */ 243 fifo_mr = at91_twi_read(dev, AT91_TWI_FMR); 244 fifo_mr &= ~AT91_TWI_FMR_TXRDYM_MASK; 245 fifo_mr |= AT91_TWI_FMR_TXRDYM(AT91_TWI_FOUR_DATA); 246 at91_twi_write(dev, AT91_TWI_FMR, fifo_mr); 247 } else { 248 sg_dma_len(&dma->sg[0]) = dev->buf_len; 249 sg_dma_address(&dma->sg[0]) = dma_addr; 250 } 251 252 txdesc = dmaengine_prep_slave_sg(chan_tx, dma->sg, sg_len, 253 DMA_MEM_TO_DEV, 254 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 255 if (!txdesc) { 256 dev_err(dev->dev, "dma prep slave sg failed\n"); 257 goto error; 258 } 259 260 txdesc->callback = at91_twi_write_data_dma_callback; 261 txdesc->callback_param = dev; 262 263 dma->xfer_in_progress = true; 264 dmaengine_submit(txdesc); 265 dma_async_issue_pending(chan_tx); 266 267 return; 268 269 error: 270 at91_twi_dma_cleanup(dev); 271 } 272 273 static void at91_twi_read_next_byte(struct at91_twi_dev *dev) 274 { 275 /* 276 * If we are in this case, it means there is garbage data in RHR, so 277 * delete them. 278 */ 279 if (!dev->buf_len) { 280 at91_twi_read(dev, AT91_TWI_RHR); 281 return; 282 } 283 284 /* 8bit read works with and without FIFO */ 285 *dev->buf = readb_relaxed(dev->base + AT91_TWI_RHR); 286 --dev->buf_len; 287 288 /* return if aborting, we only needed to read RHR to clear RXRDY*/ 289 if (dev->recv_len_abort) 290 return; 291 292 /* handle I2C_SMBUS_BLOCK_DATA */ 293 if (unlikely(dev->msg->flags & I2C_M_RECV_LEN)) { 294 /* ensure length byte is a valid value */ 295 if (*dev->buf <= I2C_SMBUS_BLOCK_MAX && *dev->buf > 0) { 296 dev->msg->flags &= ~I2C_M_RECV_LEN; 297 dev->buf_len += *dev->buf; 298 dev->msg->len = dev->buf_len + 1; 299 dev_dbg(dev->dev, "received block length %zu\n", 300 dev->buf_len); 301 } else { 302 /* abort and send the stop by reading one more byte */ 303 dev->recv_len_abort = true; 304 dev->buf_len = 1; 305 } 306 } 307 308 /* send stop if second but last byte has been read */ 309 if (!dev->use_alt_cmd && dev->buf_len == 1) 310 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); 311 312 dev_dbg(dev->dev, "read 0x%x, to go %zu\n", *dev->buf, dev->buf_len); 313 314 ++dev->buf; 315 } 316 317 static void at91_twi_read_data_dma_callback(void *data) 318 { 319 struct at91_twi_dev *dev = (struct at91_twi_dev *)data; 320 unsigned ier = AT91_TWI_TXCOMP; 321 322 dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg[0]), 323 dev->buf_len, DMA_FROM_DEVICE); 324 325 if (!dev->use_alt_cmd) { 326 /* The last two bytes have to be read without using dma */ 327 dev->buf += dev->buf_len - 2; 328 dev->buf_len = 2; 329 ier |= AT91_TWI_RXRDY; 330 } 331 at91_twi_write(dev, AT91_TWI_IER, ier); 332 } 333 334 static void at91_twi_read_data_dma(struct at91_twi_dev *dev) 335 { 336 dma_addr_t dma_addr; 337 struct dma_async_tx_descriptor *rxdesc; 338 struct at91_twi_dma *dma = &dev->dma; 339 struct dma_chan *chan_rx = dma->chan_rx; 340 size_t buf_len; 341 342 buf_len = (dev->use_alt_cmd) ? dev->buf_len : dev->buf_len - 2; 343 dma->direction = DMA_FROM_DEVICE; 344 345 /* Keep in mind that we won't use dma to read the last two bytes */ 346 at91_twi_irq_save(dev); 347 dma_addr = dma_map_single(dev->dev, dev->buf, buf_len, DMA_FROM_DEVICE); 348 if (dma_mapping_error(dev->dev, dma_addr)) { 349 dev_err(dev->dev, "dma map failed\n"); 350 return; 351 } 352 dma->buf_mapped = true; 353 at91_twi_irq_restore(dev); 354 355 if (dev->fifo_size && IS_ALIGNED(buf_len, 4)) { 356 unsigned fifo_mr; 357 358 /* 359 * DMA controller is triggered when at least 4 data can be 360 * read from the RX FIFO 361 */ 362 fifo_mr = at91_twi_read(dev, AT91_TWI_FMR); 363 fifo_mr &= ~AT91_TWI_FMR_RXRDYM_MASK; 364 fifo_mr |= AT91_TWI_FMR_RXRDYM(AT91_TWI_FOUR_DATA); 365 at91_twi_write(dev, AT91_TWI_FMR, fifo_mr); 366 } 367 368 sg_dma_len(&dma->sg[0]) = buf_len; 369 sg_dma_address(&dma->sg[0]) = dma_addr; 370 371 rxdesc = dmaengine_prep_slave_sg(chan_rx, dma->sg, 1, DMA_DEV_TO_MEM, 372 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 373 if (!rxdesc) { 374 dev_err(dev->dev, "dma prep slave sg failed\n"); 375 goto error; 376 } 377 378 rxdesc->callback = at91_twi_read_data_dma_callback; 379 rxdesc->callback_param = dev; 380 381 dma->xfer_in_progress = true; 382 dmaengine_submit(rxdesc); 383 dma_async_issue_pending(dma->chan_rx); 384 385 return; 386 387 error: 388 at91_twi_dma_cleanup(dev); 389 } 390 391 static irqreturn_t atmel_twi_interrupt(int irq, void *dev_id) 392 { 393 struct at91_twi_dev *dev = dev_id; 394 const unsigned status = at91_twi_read(dev, AT91_TWI_SR); 395 const unsigned irqstatus = status & at91_twi_read(dev, AT91_TWI_IMR); 396 397 if (!irqstatus) 398 return IRQ_NONE; 399 /* 400 * In reception, the behavior of the twi device (before sama5d2) is 401 * weird. There is some magic about RXRDY flag! When a data has been 402 * almost received, the reception of a new one is anticipated if there 403 * is no stop command to send. That is the reason why ask for sending 404 * the stop command not on the last data but on the second last one. 405 * 406 * Unfortunately, we could still have the RXRDY flag set even if the 407 * transfer is done and we have read the last data. It might happen 408 * when the i2c slave device sends too quickly data after receiving the 409 * ack from the master. The data has been almost received before having 410 * the order to send stop. In this case, sending the stop command could 411 * cause a RXRDY interrupt with a TXCOMP one. It is better to manage 412 * the RXRDY interrupt first in order to not keep garbage data in the 413 * Receive Holding Register for the next transfer. 414 */ 415 if (irqstatus & AT91_TWI_RXRDY) { 416 /* 417 * Read all available bytes at once by polling RXRDY usable w/ 418 * and w/o FIFO. With FIFO enabled we could also read RXFL and 419 * avoid polling RXRDY. 420 */ 421 do { 422 at91_twi_read_next_byte(dev); 423 } while (at91_twi_read(dev, AT91_TWI_SR) & AT91_TWI_RXRDY); 424 } 425 426 /* 427 * When a NACK condition is detected, the I2C controller sets the NACK, 428 * TXCOMP and TXRDY bits all together in the Status Register (SR). 429 * 430 * 1 - Handling NACK errors with CPU write transfer. 431 * 432 * In such case, we should not write the next byte into the Transmit 433 * Holding Register (THR) otherwise the I2C controller would start a new 434 * transfer and the I2C slave is likely to reply by another NACK. 435 * 436 * 2 - Handling NACK errors with DMA write transfer. 437 * 438 * By setting the TXRDY bit in the SR, the I2C controller also triggers 439 * the DMA controller to write the next data into the THR. Then the 440 * result depends on the hardware version of the I2C controller. 441 * 442 * 2a - Without support of the Alternative Command mode. 443 * 444 * This is the worst case: the DMA controller is triggered to write the 445 * next data into the THR, hence starting a new transfer: the I2C slave 446 * is likely to reply by another NACK. 447 * Concurrently, this interrupt handler is likely to be called to manage 448 * the first NACK before the I2C controller detects the second NACK and 449 * sets once again the NACK bit into the SR. 450 * When handling the first NACK, this interrupt handler disables the I2C 451 * controller interruptions, especially the NACK interrupt. 452 * Hence, the NACK bit is pending into the SR. This is why we should 453 * read the SR to clear all pending interrupts at the beginning of 454 * at91_do_twi_transfer() before actually starting a new transfer. 455 * 456 * 2b - With support of the Alternative Command mode. 457 * 458 * When a NACK condition is detected, the I2C controller also locks the 459 * THR (and sets the LOCK bit in the SR): even though the DMA controller 460 * is triggered by the TXRDY bit to write the next data into the THR, 461 * this data actually won't go on the I2C bus hence a second NACK is not 462 * generated. 463 */ 464 if (irqstatus & (AT91_TWI_TXCOMP | AT91_TWI_NACK)) { 465 at91_disable_twi_interrupts(dev); 466 complete(&dev->cmd_complete); 467 } else if (irqstatus & AT91_TWI_TXRDY) { 468 at91_twi_write_next_byte(dev); 469 } 470 471 /* catch error flags */ 472 dev->transfer_status |= status; 473 474 return IRQ_HANDLED; 475 } 476 477 static int at91_do_twi_transfer(struct at91_twi_dev *dev) 478 { 479 int ret; 480 unsigned long time_left; 481 bool has_unre_flag = dev->pdata->has_unre_flag; 482 bool has_alt_cmd = dev->pdata->has_alt_cmd; 483 struct i2c_bus_recovery_info *rinfo = &dev->rinfo; 484 485 /* 486 * WARNING: the TXCOMP bit in the Status Register is NOT a clear on 487 * read flag but shows the state of the transmission at the time the 488 * Status Register is read. According to the programmer datasheet, 489 * TXCOMP is set when both holding register and internal shifter are 490 * empty and STOP condition has been sent. 491 * Consequently, we should enable NACK interrupt rather than TXCOMP to 492 * detect transmission failure. 493 * Indeed let's take the case of an i2c write command using DMA. 494 * Whenever the slave doesn't acknowledge a byte, the LOCK, NACK and 495 * TXCOMP bits are set together into the Status Register. 496 * LOCK is a clear on write bit, which is set to prevent the DMA 497 * controller from sending new data on the i2c bus after a NACK 498 * condition has happened. Once locked, this i2c peripheral stops 499 * triggering the DMA controller for new data but it is more than 500 * likely that a new DMA transaction is already in progress, writing 501 * into the Transmit Holding Register. Since the peripheral is locked, 502 * these new data won't be sent to the i2c bus but they will remain 503 * into the Transmit Holding Register, so TXCOMP bit is cleared. 504 * Then when the interrupt handler is called, the Status Register is 505 * read: the TXCOMP bit is clear but NACK bit is still set. The driver 506 * manage the error properly, without waiting for timeout. 507 * This case can be reproduced easyly when writing into an at24 eeprom. 508 * 509 * Besides, the TXCOMP bit is already set before the i2c transaction 510 * has been started. For read transactions, this bit is cleared when 511 * writing the START bit into the Control Register. So the 512 * corresponding interrupt can safely be enabled just after. 513 * However for write transactions managed by the CPU, we first write 514 * into THR, so TXCOMP is cleared. Then we can safely enable TXCOMP 515 * interrupt. If TXCOMP interrupt were enabled before writing into THR, 516 * the interrupt handler would be called immediately and the i2c command 517 * would be reported as completed. 518 * Also when a write transaction is managed by the DMA controller, 519 * enabling the TXCOMP interrupt in this function may lead to a race 520 * condition since we don't know whether the TXCOMP interrupt is enabled 521 * before or after the DMA has started to write into THR. So the TXCOMP 522 * interrupt is enabled later by at91_twi_write_data_dma_callback(). 523 * Immediately after in that DMA callback, if the alternative command 524 * mode is not used, we still need to send the STOP condition manually 525 * writing the corresponding bit into the Control Register. 526 */ 527 528 dev_dbg(dev->dev, "transfer: %s %zu bytes.\n", 529 (dev->msg->flags & I2C_M_RD) ? "read" : "write", dev->buf_len); 530 531 reinit_completion(&dev->cmd_complete); 532 dev->transfer_status = 0; 533 534 /* Clear pending interrupts, such as NACK. */ 535 at91_twi_read(dev, AT91_TWI_SR); 536 537 if (dev->fifo_size) { 538 unsigned fifo_mr = at91_twi_read(dev, AT91_TWI_FMR); 539 540 /* Reset FIFO mode register */ 541 fifo_mr &= ~(AT91_TWI_FMR_TXRDYM_MASK | 542 AT91_TWI_FMR_RXRDYM_MASK); 543 fifo_mr |= AT91_TWI_FMR_TXRDYM(AT91_TWI_ONE_DATA); 544 fifo_mr |= AT91_TWI_FMR_RXRDYM(AT91_TWI_ONE_DATA); 545 at91_twi_write(dev, AT91_TWI_FMR, fifo_mr); 546 547 /* Flush FIFOs */ 548 at91_twi_write(dev, AT91_TWI_CR, 549 AT91_TWI_THRCLR | AT91_TWI_RHRCLR); 550 } 551 552 if (!dev->buf_len) { 553 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_QUICK); 554 at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); 555 } else if (dev->msg->flags & I2C_M_RD) { 556 unsigned start_flags = AT91_TWI_START; 557 558 /* if only one byte is to be read, immediately stop transfer */ 559 if (!dev->use_alt_cmd && dev->buf_len <= 1 && 560 !(dev->msg->flags & I2C_M_RECV_LEN)) 561 start_flags |= AT91_TWI_STOP; 562 at91_twi_write(dev, AT91_TWI_CR, start_flags); 563 /* 564 * When using dma without alternative command mode, the last 565 * byte has to be read manually in order to not send the stop 566 * command too late and then to receive extra data. 567 * In practice, there are some issues if you use the dma to 568 * read n-1 bytes because of latency. 569 * Reading n-2 bytes with dma and the two last ones manually 570 * seems to be the best solution. 571 */ 572 if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) { 573 at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK); 574 at91_twi_read_data_dma(dev); 575 } else { 576 at91_twi_write(dev, AT91_TWI_IER, 577 AT91_TWI_TXCOMP | 578 AT91_TWI_NACK | 579 AT91_TWI_RXRDY); 580 } 581 } else { 582 if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) { 583 at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK); 584 at91_twi_write_data_dma(dev); 585 } else { 586 at91_twi_write_next_byte(dev); 587 at91_twi_write(dev, AT91_TWI_IER, 588 AT91_TWI_TXCOMP | AT91_TWI_NACK | 589 (dev->buf_len ? AT91_TWI_TXRDY : 0)); 590 } 591 } 592 593 time_left = wait_for_completion_timeout(&dev->cmd_complete, 594 dev->adapter.timeout); 595 if (time_left == 0) { 596 dev->transfer_status |= at91_twi_read(dev, AT91_TWI_SR); 597 dev_err(dev->dev, "controller timed out\n"); 598 at91_init_twi_bus(dev); 599 ret = -ETIMEDOUT; 600 goto error; 601 } 602 if (dev->transfer_status & AT91_TWI_NACK) { 603 dev_dbg(dev->dev, "received nack\n"); 604 ret = -EREMOTEIO; 605 goto error; 606 } 607 if (dev->transfer_status & AT91_TWI_OVRE) { 608 dev_err(dev->dev, "overrun while reading\n"); 609 ret = -EIO; 610 goto error; 611 } 612 if (has_unre_flag && dev->transfer_status & AT91_TWI_UNRE) { 613 dev_err(dev->dev, "underrun while writing\n"); 614 ret = -EIO; 615 goto error; 616 } 617 if ((has_alt_cmd || dev->fifo_size) && 618 (dev->transfer_status & AT91_TWI_LOCK)) { 619 dev_err(dev->dev, "tx locked\n"); 620 ret = -EIO; 621 goto error; 622 } 623 if (dev->recv_len_abort) { 624 dev_err(dev->dev, "invalid smbus block length recvd\n"); 625 ret = -EPROTO; 626 goto error; 627 } 628 629 dev_dbg(dev->dev, "transfer complete\n"); 630 631 return 0; 632 633 error: 634 /* first stop DMA transfer if still in progress */ 635 at91_twi_dma_cleanup(dev); 636 /* then flush THR/FIFO and unlock TX if locked */ 637 if ((has_alt_cmd || dev->fifo_size) && 638 (dev->transfer_status & AT91_TWI_LOCK)) { 639 dev_dbg(dev->dev, "unlock tx\n"); 640 at91_twi_write(dev, AT91_TWI_CR, 641 AT91_TWI_THRCLR | AT91_TWI_LOCKCLR); 642 } 643 644 if (rinfo->get_sda && !(rinfo->get_sda(&dev->adapter))) { 645 dev_dbg(dev->dev, 646 "SDA is down; clear bus using gpio\n"); 647 i2c_recover_bus(&dev->adapter); 648 } 649 650 return ret; 651 } 652 653 static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num) 654 { 655 struct at91_twi_dev *dev = i2c_get_adapdata(adap); 656 int ret; 657 unsigned int_addr_flag = 0; 658 struct i2c_msg *m_start = msg; 659 bool is_read; 660 661 dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num); 662 663 ret = pm_runtime_get_sync(dev->dev); 664 if (ret < 0) 665 goto out; 666 667 if (num == 2) { 668 int internal_address = 0; 669 int i; 670 671 /* 1st msg is put into the internal address, start with 2nd */ 672 m_start = &msg[1]; 673 for (i = 0; i < msg->len; ++i) { 674 const unsigned addr = msg->buf[msg->len - 1 - i]; 675 676 internal_address |= addr << (8 * i); 677 int_addr_flag += AT91_TWI_IADRSZ_1; 678 } 679 at91_twi_write(dev, AT91_TWI_IADR, internal_address); 680 } 681 682 dev->use_alt_cmd = false; 683 is_read = (m_start->flags & I2C_M_RD); 684 if (dev->pdata->has_alt_cmd) { 685 if (m_start->len > 0 && 686 m_start->len < AT91_I2C_MAX_ALT_CMD_DATA_SIZE) { 687 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_ACMEN); 688 at91_twi_write(dev, AT91_TWI_ACR, 689 AT91_TWI_ACR_DATAL(m_start->len) | 690 ((is_read) ? AT91_TWI_ACR_DIR : 0)); 691 dev->use_alt_cmd = true; 692 } else { 693 at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_ACMDIS); 694 } 695 } 696 697 at91_twi_write(dev, AT91_TWI_MMR, 698 (m_start->addr << 16) | 699 int_addr_flag | 700 ((!dev->use_alt_cmd && is_read) ? AT91_TWI_MREAD : 0)); 701 702 dev->buf_len = m_start->len; 703 dev->buf = m_start->buf; 704 dev->msg = m_start; 705 dev->recv_len_abort = false; 706 707 ret = at91_do_twi_transfer(dev); 708 709 ret = (ret < 0) ? ret : num; 710 out: 711 pm_runtime_mark_last_busy(dev->dev); 712 pm_runtime_put_autosuspend(dev->dev); 713 714 return ret; 715 } 716 717 /* 718 * The hardware can handle at most two messages concatenated by a 719 * repeated start via it's internal address feature. 720 */ 721 static const struct i2c_adapter_quirks at91_twi_quirks = { 722 .flags = I2C_AQ_COMB | I2C_AQ_COMB_WRITE_FIRST | I2C_AQ_COMB_SAME_ADDR, 723 .max_comb_1st_msg_len = 3, 724 }; 725 726 static u32 at91_twi_func(struct i2c_adapter *adapter) 727 { 728 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL 729 | I2C_FUNC_SMBUS_READ_BLOCK_DATA; 730 } 731 732 static const struct i2c_algorithm at91_twi_algorithm = { 733 .master_xfer = at91_twi_xfer, 734 .functionality = at91_twi_func, 735 }; 736 737 static int at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr) 738 { 739 int ret = 0; 740 struct dma_slave_config slave_config; 741 struct at91_twi_dma *dma = &dev->dma; 742 enum dma_slave_buswidth addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 743 744 /* 745 * The actual width of the access will be chosen in 746 * dmaengine_prep_slave_sg(): 747 * for each buffer in the scatter-gather list, if its size is aligned 748 * to addr_width then addr_width accesses will be performed to transfer 749 * the buffer. On the other hand, if the buffer size is not aligned to 750 * addr_width then the buffer is transferred using single byte accesses. 751 * Please refer to the Atmel eXtended DMA controller driver. 752 * When FIFOs are used, the TXRDYM threshold can always be set to 753 * trigger the XDMAC when at least 4 data can be written into the TX 754 * FIFO, even if single byte accesses are performed. 755 * However the RXRDYM threshold must be set to fit the access width, 756 * deduced from buffer length, so the XDMAC is triggered properly to 757 * read data from the RX FIFO. 758 */ 759 if (dev->fifo_size) 760 addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 761 762 memset(&slave_config, 0, sizeof(slave_config)); 763 slave_config.src_addr = (dma_addr_t)phy_addr + AT91_TWI_RHR; 764 slave_config.src_addr_width = addr_width; 765 slave_config.src_maxburst = 1; 766 slave_config.dst_addr = (dma_addr_t)phy_addr + AT91_TWI_THR; 767 slave_config.dst_addr_width = addr_width; 768 slave_config.dst_maxburst = 1; 769 slave_config.device_fc = false; 770 771 dma->chan_tx = dma_request_chan(dev->dev, "tx"); 772 if (IS_ERR(dma->chan_tx)) { 773 ret = PTR_ERR(dma->chan_tx); 774 dma->chan_tx = NULL; 775 goto error; 776 } 777 778 dma->chan_rx = dma_request_chan(dev->dev, "rx"); 779 if (IS_ERR(dma->chan_rx)) { 780 ret = PTR_ERR(dma->chan_rx); 781 dma->chan_rx = NULL; 782 goto error; 783 } 784 785 slave_config.direction = DMA_MEM_TO_DEV; 786 if (dmaengine_slave_config(dma->chan_tx, &slave_config)) { 787 dev_err(dev->dev, "failed to configure tx channel\n"); 788 ret = -EINVAL; 789 goto error; 790 } 791 792 slave_config.direction = DMA_DEV_TO_MEM; 793 if (dmaengine_slave_config(dma->chan_rx, &slave_config)) { 794 dev_err(dev->dev, "failed to configure rx channel\n"); 795 ret = -EINVAL; 796 goto error; 797 } 798 799 sg_init_table(dma->sg, 2); 800 dma->buf_mapped = false; 801 dma->xfer_in_progress = false; 802 dev->use_dma = true; 803 804 dev_info(dev->dev, "using %s (tx) and %s (rx) for DMA transfers\n", 805 dma_chan_name(dma->chan_tx), dma_chan_name(dma->chan_rx)); 806 807 return ret; 808 809 error: 810 if (ret != -EPROBE_DEFER) 811 dev_info(dev->dev, "can't get DMA channel, continue without DMA support\n"); 812 if (dma->chan_rx) 813 dma_release_channel(dma->chan_rx); 814 if (dma->chan_tx) 815 dma_release_channel(dma->chan_tx); 816 return ret; 817 } 818 819 static void at91_prepare_twi_recovery(struct i2c_adapter *adap) 820 { 821 struct at91_twi_dev *dev = i2c_get_adapdata(adap); 822 823 pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_gpio); 824 } 825 826 static void at91_unprepare_twi_recovery(struct i2c_adapter *adap) 827 { 828 struct at91_twi_dev *dev = i2c_get_adapdata(adap); 829 830 pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_default); 831 } 832 833 static int at91_init_twi_recovery_info(struct platform_device *pdev, 834 struct at91_twi_dev *dev) 835 { 836 struct i2c_bus_recovery_info *rinfo = &dev->rinfo; 837 838 dev->pinctrl = devm_pinctrl_get(&pdev->dev); 839 if (!dev->pinctrl || IS_ERR(dev->pinctrl)) { 840 dev_info(dev->dev, "can't get pinctrl, bus recovery not supported\n"); 841 return PTR_ERR(dev->pinctrl); 842 } 843 844 dev->pinctrl_pins_default = pinctrl_lookup_state(dev->pinctrl, 845 PINCTRL_STATE_DEFAULT); 846 dev->pinctrl_pins_gpio = pinctrl_lookup_state(dev->pinctrl, 847 "gpio"); 848 rinfo->sda_gpiod = devm_gpiod_get(&pdev->dev, "sda", GPIOD_IN); 849 if (PTR_ERR(rinfo->sda_gpiod) == -EPROBE_DEFER) 850 return -EPROBE_DEFER; 851 852 rinfo->scl_gpiod = devm_gpiod_get(&pdev->dev, "scl", 853 GPIOD_OUT_HIGH_OPEN_DRAIN); 854 if (PTR_ERR(rinfo->scl_gpiod) == -EPROBE_DEFER) 855 return -EPROBE_DEFER; 856 857 if (IS_ERR(rinfo->sda_gpiod) || 858 IS_ERR(rinfo->scl_gpiod) || 859 IS_ERR(dev->pinctrl_pins_default) || 860 IS_ERR(dev->pinctrl_pins_gpio)) { 861 dev_info(&pdev->dev, "recovery information incomplete\n"); 862 if (!IS_ERR(rinfo->sda_gpiod)) { 863 gpiod_put(rinfo->sda_gpiod); 864 rinfo->sda_gpiod = NULL; 865 } 866 if (!IS_ERR(rinfo->scl_gpiod)) { 867 gpiod_put(rinfo->scl_gpiod); 868 rinfo->scl_gpiod = NULL; 869 } 870 return -EINVAL; 871 } 872 873 dev_info(&pdev->dev, "using scl, sda for recovery\n"); 874 875 rinfo->prepare_recovery = at91_prepare_twi_recovery; 876 rinfo->unprepare_recovery = at91_unprepare_twi_recovery; 877 rinfo->recover_bus = i2c_generic_scl_recovery; 878 dev->adapter.bus_recovery_info = rinfo; 879 880 return 0; 881 } 882 883 int at91_twi_probe_master(struct platform_device *pdev, 884 u32 phy_addr, struct at91_twi_dev *dev) 885 { 886 int rc; 887 888 init_completion(&dev->cmd_complete); 889 890 rc = devm_request_irq(&pdev->dev, dev->irq, atmel_twi_interrupt, 0, 891 dev_name(dev->dev), dev); 892 if (rc) { 893 dev_err(dev->dev, "Cannot get irq %d: %d\n", dev->irq, rc); 894 return rc; 895 } 896 897 if (dev->dev->of_node) { 898 rc = at91_twi_configure_dma(dev, phy_addr); 899 if (rc == -EPROBE_DEFER) 900 return rc; 901 } 902 903 if (!of_property_read_u32(pdev->dev.of_node, "atmel,fifo-size", 904 &dev->fifo_size)) { 905 dev_info(dev->dev, "Using FIFO (%u data)\n", dev->fifo_size); 906 } 907 908 dev->enable_dig_filt = of_property_read_bool(pdev->dev.of_node, 909 "i2c-digital-filter"); 910 911 dev->enable_ana_filt = of_property_read_bool(pdev->dev.of_node, 912 "i2c-analog-filter"); 913 at91_calc_twi_clock(dev); 914 915 rc = at91_init_twi_recovery_info(pdev, dev); 916 if (rc == -EPROBE_DEFER) 917 return rc; 918 919 dev->adapter.algo = &at91_twi_algorithm; 920 dev->adapter.quirks = &at91_twi_quirks; 921 922 return 0; 923 } 924