1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * jc42.c - driver for Jedec JC42.4 compliant temperature sensors 4 * 5 * Copyright (c) 2010 Ericsson AB. 6 * 7 * Derived from lm77.c by Andras BALI <drewie@freemail.hu>. 8 * 9 * JC42.4 compliant temperature sensors are typically used on memory modules. 10 */ 11 12 #include <linux/bitops.h> 13 #include <linux/module.h> 14 #include <linux/init.h> 15 #include <linux/slab.h> 16 #include <linux/jiffies.h> 17 #include <linux/i2c.h> 18 #include <linux/hwmon.h> 19 #include <linux/err.h> 20 #include <linux/mutex.h> 21 #include <linux/of.h> 22 23 /* Addresses to scan */ 24 static const unsigned short normal_i2c[] = { 25 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, I2C_CLIENT_END }; 26 27 /* JC42 registers. All registers are 16 bit. */ 28 #define JC42_REG_CAP 0x00 29 #define JC42_REG_CONFIG 0x01 30 #define JC42_REG_TEMP_UPPER 0x02 31 #define JC42_REG_TEMP_LOWER 0x03 32 #define JC42_REG_TEMP_CRITICAL 0x04 33 #define JC42_REG_TEMP 0x05 34 #define JC42_REG_MANID 0x06 35 #define JC42_REG_DEVICEID 0x07 36 #define JC42_REG_SMBUS 0x22 /* NXP and Atmel, possibly others? */ 37 38 /* Status bits in temperature register */ 39 #define JC42_ALARM_CRIT_BIT 15 40 #define JC42_ALARM_MAX_BIT 14 41 #define JC42_ALARM_MIN_BIT 13 42 43 /* Configuration register defines */ 44 #define JC42_CFG_CRIT_ONLY (1 << 2) 45 #define JC42_CFG_TCRIT_LOCK (1 << 6) 46 #define JC42_CFG_EVENT_LOCK (1 << 7) 47 #define JC42_CFG_SHUTDOWN (1 << 8) 48 #define JC42_CFG_HYST_SHIFT 9 49 #define JC42_CFG_HYST_MASK (0x03 << 9) 50 51 /* Capabilities */ 52 #define JC42_CAP_RANGE (1 << 2) 53 54 /* Manufacturer IDs */ 55 #define ADT_MANID 0x11d4 /* Analog Devices */ 56 #define ATMEL_MANID 0x001f /* Atmel */ 57 #define ATMEL_MANID2 0x1114 /* Atmel */ 58 #define MAX_MANID 0x004d /* Maxim */ 59 #define IDT_MANID 0x00b3 /* IDT */ 60 #define MCP_MANID 0x0054 /* Microchip */ 61 #define NXP_MANID 0x1131 /* NXP Semiconductors */ 62 #define ONS_MANID 0x1b09 /* ON Semiconductor */ 63 #define STM_MANID 0x104a /* ST Microelectronics */ 64 #define GT_MANID 0x1c68 /* Giantec */ 65 #define GT_MANID2 0x132d /* Giantec, 2nd mfg ID */ 66 67 /* SMBUS register */ 68 #define SMBUS_STMOUT BIT(7) /* SMBus time-out, active low */ 69 70 /* Supported chips */ 71 72 /* Analog Devices */ 73 #define ADT7408_DEVID 0x0801 74 #define ADT7408_DEVID_MASK 0xffff 75 76 /* Atmel */ 77 #define AT30TS00_DEVID 0x8201 78 #define AT30TS00_DEVID_MASK 0xffff 79 80 #define AT30TSE004_DEVID 0x2200 81 #define AT30TSE004_DEVID_MASK 0xffff 82 83 /* Giantec */ 84 #define GT30TS00_DEVID 0x2200 85 #define GT30TS00_DEVID_MASK 0xff00 86 87 #define GT34TS02_DEVID 0x3300 88 #define GT34TS02_DEVID_MASK 0xff00 89 90 /* IDT */ 91 #define TSE2004_DEVID 0x2200 92 #define TSE2004_DEVID_MASK 0xff00 93 94 #define TS3000_DEVID 0x2900 /* Also matches TSE2002 */ 95 #define TS3000_DEVID_MASK 0xff00 96 97 #define TS3001_DEVID 0x3000 98 #define TS3001_DEVID_MASK 0xff00 99 100 /* Maxim */ 101 #define MAX6604_DEVID 0x3e00 102 #define MAX6604_DEVID_MASK 0xffff 103 104 /* Microchip */ 105 #define MCP9804_DEVID 0x0200 106 #define MCP9804_DEVID_MASK 0xfffc 107 108 #define MCP9808_DEVID 0x0400 109 #define MCP9808_DEVID_MASK 0xfffc 110 111 #define MCP98242_DEVID 0x2000 112 #define MCP98242_DEVID_MASK 0xfffc 113 114 #define MCP98243_DEVID 0x2100 115 #define MCP98243_DEVID_MASK 0xfffc 116 117 #define MCP98244_DEVID 0x2200 118 #define MCP98244_DEVID_MASK 0xfffc 119 120 #define MCP9843_DEVID 0x0000 /* Also matches mcp9805 */ 121 #define MCP9843_DEVID_MASK 0xfffe 122 123 /* NXP */ 124 #define SE97_DEVID 0xa200 125 #define SE97_DEVID_MASK 0xfffc 126 127 #define SE98_DEVID 0xa100 128 #define SE98_DEVID_MASK 0xfffc 129 130 /* ON Semiconductor */ 131 #define CAT6095_DEVID 0x0800 /* Also matches CAT34TS02 */ 132 #define CAT6095_DEVID_MASK 0xffe0 133 134 #define CAT34TS02C_DEVID 0x0a00 135 #define CAT34TS02C_DEVID_MASK 0xfff0 136 137 #define CAT34TS04_DEVID 0x2200 138 #define CAT34TS04_DEVID_MASK 0xfff0 139 140 /* ST Microelectronics */ 141 #define STTS424_DEVID 0x0101 142 #define STTS424_DEVID_MASK 0xffff 143 144 #define STTS424E_DEVID 0x0000 145 #define STTS424E_DEVID_MASK 0xfffe 146 147 #define STTS2002_DEVID 0x0300 148 #define STTS2002_DEVID_MASK 0xffff 149 150 #define STTS2004_DEVID 0x2201 151 #define STTS2004_DEVID_MASK 0xffff 152 153 #define STTS3000_DEVID 0x0200 154 #define STTS3000_DEVID_MASK 0xffff 155 156 static u16 jc42_hysteresis[] = { 0, 1500, 3000, 6000 }; 157 158 struct jc42_chips { 159 u16 manid; 160 u16 devid; 161 u16 devid_mask; 162 }; 163 164 static struct jc42_chips jc42_chips[] = { 165 { ADT_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK }, 166 { ATMEL_MANID, AT30TS00_DEVID, AT30TS00_DEVID_MASK }, 167 { ATMEL_MANID2, AT30TSE004_DEVID, AT30TSE004_DEVID_MASK }, 168 { GT_MANID, GT30TS00_DEVID, GT30TS00_DEVID_MASK }, 169 { GT_MANID2, GT34TS02_DEVID, GT34TS02_DEVID_MASK }, 170 { IDT_MANID, TSE2004_DEVID, TSE2004_DEVID_MASK }, 171 { IDT_MANID, TS3000_DEVID, TS3000_DEVID_MASK }, 172 { IDT_MANID, TS3001_DEVID, TS3001_DEVID_MASK }, 173 { MAX_MANID, MAX6604_DEVID, MAX6604_DEVID_MASK }, 174 { MCP_MANID, MCP9804_DEVID, MCP9804_DEVID_MASK }, 175 { MCP_MANID, MCP9808_DEVID, MCP9808_DEVID_MASK }, 176 { MCP_MANID, MCP98242_DEVID, MCP98242_DEVID_MASK }, 177 { MCP_MANID, MCP98243_DEVID, MCP98243_DEVID_MASK }, 178 { MCP_MANID, MCP98244_DEVID, MCP98244_DEVID_MASK }, 179 { MCP_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK }, 180 { NXP_MANID, SE97_DEVID, SE97_DEVID_MASK }, 181 { ONS_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK }, 182 { ONS_MANID, CAT34TS02C_DEVID, CAT34TS02C_DEVID_MASK }, 183 { ONS_MANID, CAT34TS04_DEVID, CAT34TS04_DEVID_MASK }, 184 { NXP_MANID, SE98_DEVID, SE98_DEVID_MASK }, 185 { STM_MANID, STTS424_DEVID, STTS424_DEVID_MASK }, 186 { STM_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK }, 187 { STM_MANID, STTS2002_DEVID, STTS2002_DEVID_MASK }, 188 { STM_MANID, STTS2004_DEVID, STTS2004_DEVID_MASK }, 189 { STM_MANID, STTS3000_DEVID, STTS3000_DEVID_MASK }, 190 }; 191 192 enum temp_index { 193 t_input = 0, 194 t_crit, 195 t_min, 196 t_max, 197 t_num_temp 198 }; 199 200 static const u8 temp_regs[t_num_temp] = { 201 [t_input] = JC42_REG_TEMP, 202 [t_crit] = JC42_REG_TEMP_CRITICAL, 203 [t_min] = JC42_REG_TEMP_LOWER, 204 [t_max] = JC42_REG_TEMP_UPPER, 205 }; 206 207 /* Each client has this additional data */ 208 struct jc42_data { 209 struct i2c_client *client; 210 struct mutex update_lock; /* protect register access */ 211 bool extended; /* true if extended range supported */ 212 bool valid; 213 unsigned long last_updated; /* In jiffies */ 214 u16 orig_config; /* original configuration */ 215 u16 config; /* current configuration */ 216 u16 temp[t_num_temp];/* Temperatures */ 217 }; 218 219 #define JC42_TEMP_MIN_EXTENDED (-40000) 220 #define JC42_TEMP_MIN 0 221 #define JC42_TEMP_MAX 125000 222 223 static u16 jc42_temp_to_reg(long temp, bool extended) 224 { 225 int ntemp = clamp_val(temp, 226 extended ? JC42_TEMP_MIN_EXTENDED : 227 JC42_TEMP_MIN, JC42_TEMP_MAX); 228 229 /* convert from 0.001 to 0.0625 resolution */ 230 return (ntemp * 2 / 125) & 0x1fff; 231 } 232 233 static int jc42_temp_from_reg(s16 reg) 234 { 235 reg = sign_extend32(reg, 12); 236 237 /* convert from 0.0625 to 0.001 resolution */ 238 return reg * 125 / 2; 239 } 240 241 static struct jc42_data *jc42_update_device(struct device *dev) 242 { 243 struct jc42_data *data = dev_get_drvdata(dev); 244 struct i2c_client *client = data->client; 245 struct jc42_data *ret = data; 246 int i, val; 247 248 mutex_lock(&data->update_lock); 249 250 if (time_after(jiffies, data->last_updated + HZ) || !data->valid) { 251 for (i = 0; i < t_num_temp; i++) { 252 val = i2c_smbus_read_word_swapped(client, temp_regs[i]); 253 if (val < 0) { 254 ret = ERR_PTR(val); 255 goto abort; 256 } 257 data->temp[i] = val; 258 } 259 data->last_updated = jiffies; 260 data->valid = true; 261 } 262 abort: 263 mutex_unlock(&data->update_lock); 264 return ret; 265 } 266 267 static int jc42_read(struct device *dev, enum hwmon_sensor_types type, 268 u32 attr, int channel, long *val) 269 { 270 struct jc42_data *data = jc42_update_device(dev); 271 int temp, hyst; 272 273 if (IS_ERR(data)) 274 return PTR_ERR(data); 275 276 switch (attr) { 277 case hwmon_temp_input: 278 *val = jc42_temp_from_reg(data->temp[t_input]); 279 return 0; 280 case hwmon_temp_min: 281 *val = jc42_temp_from_reg(data->temp[t_min]); 282 return 0; 283 case hwmon_temp_max: 284 *val = jc42_temp_from_reg(data->temp[t_max]); 285 return 0; 286 case hwmon_temp_crit: 287 *val = jc42_temp_from_reg(data->temp[t_crit]); 288 return 0; 289 case hwmon_temp_max_hyst: 290 temp = jc42_temp_from_reg(data->temp[t_max]); 291 hyst = jc42_hysteresis[(data->config & JC42_CFG_HYST_MASK) 292 >> JC42_CFG_HYST_SHIFT]; 293 *val = temp - hyst; 294 return 0; 295 case hwmon_temp_crit_hyst: 296 temp = jc42_temp_from_reg(data->temp[t_crit]); 297 hyst = jc42_hysteresis[(data->config & JC42_CFG_HYST_MASK) 298 >> JC42_CFG_HYST_SHIFT]; 299 *val = temp - hyst; 300 return 0; 301 case hwmon_temp_min_alarm: 302 *val = (data->temp[t_input] >> JC42_ALARM_MIN_BIT) & 1; 303 return 0; 304 case hwmon_temp_max_alarm: 305 *val = (data->temp[t_input] >> JC42_ALARM_MAX_BIT) & 1; 306 return 0; 307 case hwmon_temp_crit_alarm: 308 *val = (data->temp[t_input] >> JC42_ALARM_CRIT_BIT) & 1; 309 return 0; 310 default: 311 return -EOPNOTSUPP; 312 } 313 } 314 315 static int jc42_write(struct device *dev, enum hwmon_sensor_types type, 316 u32 attr, int channel, long val) 317 { 318 struct jc42_data *data = dev_get_drvdata(dev); 319 struct i2c_client *client = data->client; 320 int diff, hyst; 321 int ret; 322 323 mutex_lock(&data->update_lock); 324 325 switch (attr) { 326 case hwmon_temp_min: 327 data->temp[t_min] = jc42_temp_to_reg(val, data->extended); 328 ret = i2c_smbus_write_word_swapped(client, temp_regs[t_min], 329 data->temp[t_min]); 330 break; 331 case hwmon_temp_max: 332 data->temp[t_max] = jc42_temp_to_reg(val, data->extended); 333 ret = i2c_smbus_write_word_swapped(client, temp_regs[t_max], 334 data->temp[t_max]); 335 break; 336 case hwmon_temp_crit: 337 data->temp[t_crit] = jc42_temp_to_reg(val, data->extended); 338 ret = i2c_smbus_write_word_swapped(client, temp_regs[t_crit], 339 data->temp[t_crit]); 340 break; 341 case hwmon_temp_crit_hyst: 342 /* 343 * JC42.4 compliant chips only support four hysteresis values. 344 * Pick best choice and go from there. 345 */ 346 val = clamp_val(val, (data->extended ? JC42_TEMP_MIN_EXTENDED 347 : JC42_TEMP_MIN) - 6000, 348 JC42_TEMP_MAX); 349 diff = jc42_temp_from_reg(data->temp[t_crit]) - val; 350 hyst = 0; 351 if (diff > 0) { 352 if (diff < 2250) 353 hyst = 1; /* 1.5 degrees C */ 354 else if (diff < 4500) 355 hyst = 2; /* 3.0 degrees C */ 356 else 357 hyst = 3; /* 6.0 degrees C */ 358 } 359 data->config = (data->config & ~JC42_CFG_HYST_MASK) | 360 (hyst << JC42_CFG_HYST_SHIFT); 361 ret = i2c_smbus_write_word_swapped(data->client, 362 JC42_REG_CONFIG, 363 data->config); 364 break; 365 default: 366 ret = -EOPNOTSUPP; 367 break; 368 } 369 370 mutex_unlock(&data->update_lock); 371 372 return ret; 373 } 374 375 static umode_t jc42_is_visible(const void *_data, enum hwmon_sensor_types type, 376 u32 attr, int channel) 377 { 378 const struct jc42_data *data = _data; 379 unsigned int config = data->config; 380 umode_t mode = 0444; 381 382 switch (attr) { 383 case hwmon_temp_min: 384 case hwmon_temp_max: 385 if (!(config & JC42_CFG_EVENT_LOCK)) 386 mode |= 0200; 387 break; 388 case hwmon_temp_crit: 389 if (!(config & JC42_CFG_TCRIT_LOCK)) 390 mode |= 0200; 391 break; 392 case hwmon_temp_crit_hyst: 393 if (!(config & (JC42_CFG_EVENT_LOCK | JC42_CFG_TCRIT_LOCK))) 394 mode |= 0200; 395 break; 396 case hwmon_temp_input: 397 case hwmon_temp_max_hyst: 398 case hwmon_temp_min_alarm: 399 case hwmon_temp_max_alarm: 400 case hwmon_temp_crit_alarm: 401 break; 402 default: 403 mode = 0; 404 break; 405 } 406 return mode; 407 } 408 409 /* Return 0 if detection is successful, -ENODEV otherwise */ 410 static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info) 411 { 412 struct i2c_adapter *adapter = client->adapter; 413 int i, config, cap, manid, devid; 414 415 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | 416 I2C_FUNC_SMBUS_WORD_DATA)) 417 return -ENODEV; 418 419 cap = i2c_smbus_read_word_swapped(client, JC42_REG_CAP); 420 config = i2c_smbus_read_word_swapped(client, JC42_REG_CONFIG); 421 manid = i2c_smbus_read_word_swapped(client, JC42_REG_MANID); 422 devid = i2c_smbus_read_word_swapped(client, JC42_REG_DEVICEID); 423 424 if (cap < 0 || config < 0 || manid < 0 || devid < 0) 425 return -ENODEV; 426 427 if ((cap & 0xff00) || (config & 0xf800)) 428 return -ENODEV; 429 430 for (i = 0; i < ARRAY_SIZE(jc42_chips); i++) { 431 struct jc42_chips *chip = &jc42_chips[i]; 432 if (manid == chip->manid && 433 (devid & chip->devid_mask) == chip->devid) { 434 strlcpy(info->type, "jc42", I2C_NAME_SIZE); 435 return 0; 436 } 437 } 438 return -ENODEV; 439 } 440 441 static const struct hwmon_channel_info *jc42_info[] = { 442 HWMON_CHANNEL_INFO(temp, 443 HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | 444 HWMON_T_CRIT | HWMON_T_MAX_HYST | 445 HWMON_T_CRIT_HYST | HWMON_T_MIN_ALARM | 446 HWMON_T_MAX_ALARM | HWMON_T_CRIT_ALARM), 447 NULL 448 }; 449 450 static const struct hwmon_ops jc42_hwmon_ops = { 451 .is_visible = jc42_is_visible, 452 .read = jc42_read, 453 .write = jc42_write, 454 }; 455 456 static const struct hwmon_chip_info jc42_chip_info = { 457 .ops = &jc42_hwmon_ops, 458 .info = jc42_info, 459 }; 460 461 static int jc42_probe(struct i2c_client *client) 462 { 463 struct device *dev = &client->dev; 464 struct device *hwmon_dev; 465 struct jc42_data *data; 466 int config, cap; 467 468 data = devm_kzalloc(dev, sizeof(struct jc42_data), GFP_KERNEL); 469 if (!data) 470 return -ENOMEM; 471 472 data->client = client; 473 i2c_set_clientdata(client, data); 474 mutex_init(&data->update_lock); 475 476 cap = i2c_smbus_read_word_swapped(client, JC42_REG_CAP); 477 if (cap < 0) 478 return cap; 479 480 data->extended = !!(cap & JC42_CAP_RANGE); 481 482 if (device_property_read_bool(dev, "smbus-timeout-disable")) { 483 int smbus; 484 485 /* 486 * Not all chips support this register, but from a 487 * quick read of various datasheets no chip appears 488 * incompatible with the below attempt to disable 489 * the timeout. And the whole thing is opt-in... 490 */ 491 smbus = i2c_smbus_read_word_swapped(client, JC42_REG_SMBUS); 492 if (smbus < 0) 493 return smbus; 494 i2c_smbus_write_word_swapped(client, JC42_REG_SMBUS, 495 smbus | SMBUS_STMOUT); 496 } 497 498 config = i2c_smbus_read_word_swapped(client, JC42_REG_CONFIG); 499 if (config < 0) 500 return config; 501 502 data->orig_config = config; 503 if (config & JC42_CFG_SHUTDOWN) { 504 config &= ~JC42_CFG_SHUTDOWN; 505 i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config); 506 } 507 data->config = config; 508 509 hwmon_dev = devm_hwmon_device_register_with_info(dev, "jc42", 510 data, &jc42_chip_info, 511 NULL); 512 return PTR_ERR_OR_ZERO(hwmon_dev); 513 } 514 515 static int jc42_remove(struct i2c_client *client) 516 { 517 struct jc42_data *data = i2c_get_clientdata(client); 518 519 /* Restore original configuration except hysteresis */ 520 if ((data->config & ~JC42_CFG_HYST_MASK) != 521 (data->orig_config & ~JC42_CFG_HYST_MASK)) { 522 int config; 523 524 config = (data->orig_config & ~JC42_CFG_HYST_MASK) 525 | (data->config & JC42_CFG_HYST_MASK); 526 i2c_smbus_write_word_swapped(client, JC42_REG_CONFIG, config); 527 } 528 return 0; 529 } 530 531 #ifdef CONFIG_PM 532 533 static int jc42_suspend(struct device *dev) 534 { 535 struct jc42_data *data = dev_get_drvdata(dev); 536 537 data->config |= JC42_CFG_SHUTDOWN; 538 i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG, 539 data->config); 540 return 0; 541 } 542 543 static int jc42_resume(struct device *dev) 544 { 545 struct jc42_data *data = dev_get_drvdata(dev); 546 547 data->config &= ~JC42_CFG_SHUTDOWN; 548 i2c_smbus_write_word_swapped(data->client, JC42_REG_CONFIG, 549 data->config); 550 return 0; 551 } 552 553 static const struct dev_pm_ops jc42_dev_pm_ops = { 554 .suspend = jc42_suspend, 555 .resume = jc42_resume, 556 }; 557 558 #define JC42_DEV_PM_OPS (&jc42_dev_pm_ops) 559 #else 560 #define JC42_DEV_PM_OPS NULL 561 #endif /* CONFIG_PM */ 562 563 static const struct i2c_device_id jc42_id[] = { 564 { "jc42", 0 }, 565 { } 566 }; 567 MODULE_DEVICE_TABLE(i2c, jc42_id); 568 569 #ifdef CONFIG_OF 570 static const struct of_device_id jc42_of_ids[] = { 571 { .compatible = "jedec,jc-42.4-temp", }, 572 { } 573 }; 574 MODULE_DEVICE_TABLE(of, jc42_of_ids); 575 #endif 576 577 static struct i2c_driver jc42_driver = { 578 .class = I2C_CLASS_SPD | I2C_CLASS_HWMON, 579 .driver = { 580 .name = "jc42", 581 .pm = JC42_DEV_PM_OPS, 582 .of_match_table = of_match_ptr(jc42_of_ids), 583 }, 584 .probe_new = jc42_probe, 585 .remove = jc42_remove, 586 .id_table = jc42_id, 587 .detect = jc42_detect, 588 .address_list = normal_i2c, 589 }; 590 591 module_i2c_driver(jc42_driver); 592 593 MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); 594 MODULE_DESCRIPTION("JC42 driver"); 595 MODULE_LICENSE("GPL"); 596