drivers/hwmon/bt1-pvt.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
 *
 * Authors:
 *   Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
 *   Serge Semin <Sergey.Semin@baikalelectronics.ru>
 *
 * Baikal-T1 Process, Voltage, Temperature sensor driver
 */

#include <linux/bitfield.h>
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/completion.h>
#include <linux/device.h>
#include <linux/hwmon-sysfs.h>
#include <linux/hwmon.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/ktime.h>
#include <linux/limits.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/seqlock.h>
#include <linux/sysfs.h>
#include <linux/types.h>

#include "bt1-pvt.h"

/*
 * For the sake of the code simplification we created the sensors info table
 * with the sensor names, activation modes, threshold registers base address
 * and the thresholds bit fields.
 */
static const struct pvt_sensor_info pvt_info[] = {
	PVT_SENSOR_INFO(0, "CPU Core Temperature", hwmon_temp, TEMP, TTHRES),
	PVT_SENSOR_INFO(0, "CPU Core Voltage", hwmon_in, VOLT, VTHRES),
	PVT_SENSOR_INFO(1, "CPU Core Low-Vt", hwmon_in, LVT, LTHRES),
	PVT_SENSOR_INFO(2, "CPU Core High-Vt", hwmon_in, HVT, HTHRES),
	PVT_SENSOR_INFO(3, "CPU Core Standard-Vt", hwmon_in, SVT, STHRES),
};

/*
 * The original translation formulae of the temperature (in degrees of Celsius)
 * to PVT data and vice-versa are following:
 * N = 1.8322e-8*(T^4) + 2.343e-5*(T^3) + 8.7018e-3*(T^2) + 3.9269*(T^1) +
 *     1.7204e2,
 * T = -1.6743e-11*(N^4) + 8.1542e-8*(N^3) + -1.8201e-4*(N^2) +
 *     3.1020e-1*(N^1) - 4.838e1,
 * where T = [-48.380, 147.438]C and N = [0, 1023].
 * They must be accordingly altered to be suitable for the integer arithmetics.
 * The technique is called 'factor redistribution', which just makes sure the
 * multiplications and divisions are made so to have a result of the operations
 * within the integer numbers limit. In addition we need to translate the
 * formulae to accept millidegrees of Celsius. Here what they look like after
 * the alterations:
 * N = (18322e-20*(T^4) + 2343e-13*(T^3) + 87018e-9*(T^2) + 39269e-3*T +
 *     17204e2) / 1e4,
 * T = -16743e-12*(D^4) + 81542e-9*(D^3) - 182010e-6*(D^2) + 310200e-3*D -
 *     48380,
 * where T = [-48380, 147438] mC and N = [0, 1023].
 */
static const struct pvt_poly poly_temp_to_N = {
	.total_divider = 10000,
	.terms = {
		{4, 18322, 10000, 10000},
		{3, 2343, 10000, 10},
		{2, 87018, 10000, 10},
		{1, 39269, 1000, 1},
		{0, 1720400, 1, 1}
	}
};

static const struct pvt_poly poly_N_to_temp = {
	.total_divider = 1,
	.terms = {
		{4, -16743, 1000, 1},
		{3, 81542, 1000, 1},
		{2, -182010, 1000, 1},
		{1, 310200, 1000, 1},
		{0, -48380, 1, 1}
	}
};

/*
 * Similar alterations are performed for the voltage conversion equations.
 * The original formulae are:
 * N = 1.8658e3*V - 1.1572e3,
 * V = (N + 1.1572e3) / 1.8658e3,
 * where V = [0.620, 1.168] V and N = [0, 1023].
 * After the optimization they looks as follows:
 * N = (18658e-3*V - 11572) / 10,
 * V = N * 10^5 / 18658 + 11572 * 10^4 / 18658.
 */
static const struct pvt_poly poly_volt_to_N = {
	.total_divider = 10,
	.terms = {
		{1, 18658, 1000, 1},
		{0, -11572, 1, 1}
	}
};

static const struct pvt_poly poly_N_to_volt = {
	.total_divider = 10,
	.terms = {
		{1, 100000, 18658, 1},
		{0, 115720000, 1, 18658}
	}
};

/*
 * Here is the polynomial calculation function, which performs the
 * redistributed terms calculations. It's pretty straightforward. We walk
 * over each degree term up to the free one, and perform the redistributed
 * multiplication of the term coefficient, its divider (as for the rationale
 * fraction representation), data power and the rational fraction divider
 * leftover. Then all of this is collected in a total sum variable, which
 * value is normalized by the total divider before being returned.
 */
static long pvt_calc_poly(const struct pvt_poly *poly, long data)
{
	const struct pvt_poly_term *term = poly->terms;
	long tmp, ret = 0;
	int deg;

	do {
		tmp = term->coef;
		for (deg = 0; deg < term->deg; ++deg)
			tmp = mult_frac(tmp, data, term->divider);
		ret += tmp / term->divider_leftover;
	} while ((term++)->deg);

	return ret / poly->total_divider;
}

static inline u32 pvt_update(void __iomem *reg, u32 mask, u32 data)
{
	u32 old;

	old = readl_relaxed(reg);
	writel((old & ~mask) | (data & mask), reg);

	return old & mask;
}

/*
 * Baikal-T1 PVT mode can be updated only when the controller is disabled.
 * So first we disable it, then set the new mode together with the controller
 * getting back enabled. The same concerns the temperature trim and
 * measurements timeout. If it is necessary the interface mutex is supposed
 * to be locked at the time the operations are performed.
 */
static inline void pvt_set_mode(struct pvt_hwmon *pvt, u32 mode)
{
	u32 old;

	mode = FIELD_PREP(PVT_CTRL_MODE_MASK, mode);

	old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_MODE_MASK | PVT_CTRL_EN,
		   mode | old);
}

static inline u32 pvt_calc_trim(long temp)
{
	temp = clamp_val(temp, 0, PVT_TRIM_TEMP);

	return DIV_ROUND_UP(temp, PVT_TRIM_STEP);
}

static inline void pvt_set_trim(struct pvt_hwmon *pvt, u32 trim)
{
	u32 old;

	trim = FIELD_PREP(PVT_CTRL_TRIM_MASK, trim);

	old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_TRIM_MASK | PVT_CTRL_EN,
		   trim | old);
}

static inline void pvt_set_tout(struct pvt_hwmon *pvt, u32 tout)
{
	u32 old;

	old = pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	writel(tout, pvt->regs + PVT_TTIMEOUT);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, old);
}

/*
 * This driver can optionally provide the hwmon alarms for each sensor the PVT
 * controller supports. The alarms functionality is made compile-time
 * configurable due to the hardware interface implementation peculiarity
 * described further in this comment. So in case if alarms are unnecessary in
 * your system design it's recommended to have them disabled to prevent the PVT
 * IRQs being periodically raised to get the data cache/alarms status up to
 * date.
 *
 * Baikal-T1 PVT embedded controller is based on the Analog Bits PVT sensor,
 * but is equipped with a dedicated control wrapper. It exposes the PVT
 * sub-block registers space via the APB3 bus. In addition the wrapper provides
 * a common interrupt vector of the sensors conversion completion events and
 * threshold value alarms. Alas the wrapper interface hasn't been fully thought
 * through. There is only one sensor can be activated at a time, for which the
 * thresholds comparator is enabled right after the data conversion is
 * completed. Due to this if alarms need to be implemented for all available
 * sensors we can't just set the thresholds and enable the interrupts. We need
 * to enable the sensors one after another and let the controller to detect
 * the alarms by itself at each conversion. This also makes pointless to handle
 * the alarms interrupts, since in occasion they happen synchronously with
 * data conversion completion. The best driver design would be to have the
 * completion interrupts enabled only and keep the converted value in the
 * driver data cache. This solution is implemented if hwmon alarms are enabled
 * in this driver. In case if the alarms are disabled, the conversion is
 * performed on demand at the time a sensors input file is read.
 */

#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)

#define pvt_hard_isr NULL

static irqreturn_t pvt_soft_isr(int irq, void *data)
{
	const struct pvt_sensor_info *info;
	struct pvt_hwmon *pvt = data;
	struct pvt_cache *cache;
	u32 val, thres_sts, old;

	/*
	 * DVALID bit will be cleared by reading the data. We need to save the
	 * status before the next conversion happens. Threshold events will be
	 * handled a bit later.
	 */
	thres_sts = readl(pvt->regs + PVT_RAW_INTR_STAT);

	/*
	 * Then lets recharge the PVT interface with the next sampling mode.
	 * Lock the interface mutex to serialize trim, timeouts and alarm
	 * thresholds settings.
	 */
	cache = &pvt->cache[pvt->sensor];
	info = &pvt_info[pvt->sensor];
	pvt->sensor = (pvt->sensor == PVT_SENSOR_LAST) ?
		      PVT_SENSOR_FIRST : (pvt->sensor + 1);

	/*
	 * For some reason we have to mask the interrupt before changing the
	 * mode, otherwise sometimes the temperature mode doesn't get
	 * activated even though the actual mode in the ctrl register
	 * corresponds to one. Then we read the data. By doing so we also
	 * recharge the data conversion. After this the mode corresponding
	 * to the next sensor in the row is set. Finally we enable the
	 * interrupts back.
	 */
	mutex_lock(&pvt->iface_mtx);

	old = pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
			 PVT_INTR_DVALID);

	val = readl(pvt->regs + PVT_DATA);

	pvt_set_mode(pvt, pvt_info[pvt->sensor].mode);

	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, old);

	mutex_unlock(&pvt->iface_mtx);

	/*
	 * We can now update the data cache with data just retrieved from the
	 * sensor. Lock write-seqlock to make sure the reader has a coherent
	 * data.
	 */
	write_seqlock(&cache->data_seqlock);

	cache->data = FIELD_GET(PVT_DATA_DATA_MASK, val);

	write_sequnlock(&cache->data_seqlock);

	/*
	 * While PVT core is doing the next mode data conversion, we'll check
	 * whether the alarms were triggered for the current sensor. Note that
	 * according to the documentation only one threshold IRQ status can be
	 * set at a time, that's why if-else statement is utilized.
	 */
	if ((thres_sts & info->thres_sts_lo) ^ cache->thres_sts_lo) {
		WRITE_ONCE(cache->thres_sts_lo, thres_sts & info->thres_sts_lo);
		hwmon_notify_event(pvt->hwmon, info->type, info->attr_min_alarm,
				   info->channel);
	} else if ((thres_sts & info->thres_sts_hi) ^ cache->thres_sts_hi) {
		WRITE_ONCE(cache->thres_sts_hi, thres_sts & info->thres_sts_hi);
		hwmon_notify_event(pvt->hwmon, info->type, info->attr_max_alarm,
				   info->channel);
	}

	return IRQ_HANDLED;
}

inline umode_t pvt_limit_is_visible(enum pvt_sensor_type type)
{
	return 0644;
}

inline umode_t pvt_alarm_is_visible(enum pvt_sensor_type type)
{
	return 0444;
}

static int pvt_read_data(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			 long *val)
{
	struct pvt_cache *cache = &pvt->cache[type];
	unsigned int seq;
	u32 data;

	do {
		seq = read_seqbegin(&cache->data_seqlock);
		data = cache->data;
	} while (read_seqretry(&cache->data_seqlock, seq));

	if (type == PVT_TEMP)
		*val = pvt_calc_poly(&poly_N_to_temp, data);
	else
		*val = pvt_calc_poly(&poly_N_to_volt, data);

	return 0;
}

static int pvt_read_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			  bool is_low, long *val)
{
	u32 data;

	/* No need in serialization, since it is just read from MMIO. */
	data = readl(pvt->regs + pvt_info[type].thres_base);

	if (is_low)
		data = FIELD_GET(PVT_THRES_LO_MASK, data);
	else
		data = FIELD_GET(PVT_THRES_HI_MASK, data);

	if (type == PVT_TEMP)
		*val = pvt_calc_poly(&poly_N_to_temp, data);
	else
		*val = pvt_calc_poly(&poly_N_to_volt, data);

	return 0;
}

static int pvt_write_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			   bool is_low, long val)
{
	u32 data, limit, mask;
	int ret;

	if (type == PVT_TEMP) {
		val = clamp(val, PVT_TEMP_MIN, PVT_TEMP_MAX);
		data = pvt_calc_poly(&poly_temp_to_N, val);
	} else {
		val = clamp(val, PVT_VOLT_MIN, PVT_VOLT_MAX);
		data = pvt_calc_poly(&poly_volt_to_N, val);
	}

	/* Serialize limit update, since a part of the register is changed. */
	ret = mutex_lock_interruptible(&pvt->iface_mtx);
	if (ret)
		return ret;

	/* Make sure the upper and lower ranges don't intersect. */
	limit = readl(pvt->regs + pvt_info[type].thres_base);
	if (is_low) {
		limit = FIELD_GET(PVT_THRES_HI_MASK, limit);
		data = clamp_val(data, PVT_DATA_MIN, limit);
		data = FIELD_PREP(PVT_THRES_LO_MASK, data);
		mask = PVT_THRES_LO_MASK;
	} else {
		limit = FIELD_GET(PVT_THRES_LO_MASK, limit);
		data = clamp_val(data, limit, PVT_DATA_MAX);
		data = FIELD_PREP(PVT_THRES_HI_MASK, data);
		mask = PVT_THRES_HI_MASK;
	}

	pvt_update(pvt->regs + pvt_info[type].thres_base, mask, data);

	mutex_unlock(&pvt->iface_mtx);

	return 0;
}

static int pvt_read_alarm(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			  bool is_low, long *val)
{
	if (is_low)
		*val = !!READ_ONCE(pvt->cache[type].thres_sts_lo);
	else
		*val = !!READ_ONCE(pvt->cache[type].thres_sts_hi);

	return 0;
}

static const struct hwmon_channel_info *pvt_channel_info[] = {
	HWMON_CHANNEL_INFO(chip,
			   HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL),
	HWMON_CHANNEL_INFO(temp,
			   HWMON_T_INPUT | HWMON_T_TYPE | HWMON_T_LABEL |
			   HWMON_T_MIN | HWMON_T_MIN_ALARM |
			   HWMON_T_MAX | HWMON_T_MAX_ALARM |
			   HWMON_T_OFFSET),
	HWMON_CHANNEL_INFO(in,
			   HWMON_I_INPUT | HWMON_I_LABEL |
			   HWMON_I_MIN | HWMON_I_MIN_ALARM |
			   HWMON_I_MAX | HWMON_I_MAX_ALARM,
			   HWMON_I_INPUT | HWMON_I_LABEL |
			   HWMON_I_MIN | HWMON_I_MIN_ALARM |
			   HWMON_I_MAX | HWMON_I_MAX_ALARM,
			   HWMON_I_INPUT | HWMON_I_LABEL |
			   HWMON_I_MIN | HWMON_I_MIN_ALARM |
			   HWMON_I_MAX | HWMON_I_MAX_ALARM,
			   HWMON_I_INPUT | HWMON_I_LABEL |
			   HWMON_I_MIN | HWMON_I_MIN_ALARM |
			   HWMON_I_MAX | HWMON_I_MAX_ALARM),
	NULL
};

#else /* !CONFIG_SENSORS_BT1_PVT_ALARMS */

static irqreturn_t pvt_hard_isr(int irq, void *data)
{
	struct pvt_hwmon *pvt = data;
	struct pvt_cache *cache;
	u32 val;

	/*
	 * Mask the DVALID interrupt so after exiting from the handler a
	 * repeated conversion wouldn't happen.
	 */
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
		   PVT_INTR_DVALID);

	/*
	 * Nothing special for alarm-less driver. Just read the data, update
	 * the cache and notify a waiter of this event.
	 */
	val = readl(pvt->regs + PVT_DATA);
	if (!(val & PVT_DATA_VALID)) {
		dev_err(pvt->dev, "Got IRQ when data isn't valid\n");
		return IRQ_HANDLED;
	}

	cache = &pvt->cache[pvt->sensor];

	WRITE_ONCE(cache->data, FIELD_GET(PVT_DATA_DATA_MASK, val));

	complete(&cache->conversion);

	return IRQ_HANDLED;
}

#define pvt_soft_isr NULL

inline umode_t pvt_limit_is_visible(enum pvt_sensor_type type)
{
	return 0;
}

inline umode_t pvt_alarm_is_visible(enum pvt_sensor_type type)
{
	return 0;
}

static int pvt_read_data(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			 long *val)
{
	struct pvt_cache *cache = &pvt->cache[type];
	u32 data;
	int ret;

	/*
	 * Lock PVT conversion interface until data cache is updated. The
	 * data read procedure is following: set the requested PVT sensor
	 * mode, enable IRQ and conversion, wait until conversion is finished,
	 * then disable conversion and IRQ, and read the cached data.
	 */
	ret = mutex_lock_interruptible(&pvt->iface_mtx);
	if (ret)
		return ret;

	pvt->sensor = type;
	pvt_set_mode(pvt, pvt_info[type].mode);

	/*
	 * Unmask the DVALID interrupt and enable the sensors conversions.
	 * Do the reverse procedure when conversion is done.
	 */
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, 0);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, PVT_CTRL_EN);

	wait_for_completion(&cache->conversion);

	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
		   PVT_INTR_DVALID);

	data = READ_ONCE(cache->data);

	mutex_unlock(&pvt->iface_mtx);

	if (type == PVT_TEMP)
		*val = pvt_calc_poly(&poly_N_to_temp, data);
	else
		*val = pvt_calc_poly(&poly_N_to_volt, data);

	return 0;
}

static int pvt_read_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			  bool is_low, long *val)
{
	return -EOPNOTSUPP;
}

static int pvt_write_limit(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			   bool is_low, long val)
{
	return -EOPNOTSUPP;
}

static int pvt_read_alarm(struct pvt_hwmon *pvt, enum pvt_sensor_type type,
			  bool is_low, long *val)
{
	return -EOPNOTSUPP;
}

static const struct hwmon_channel_info *pvt_channel_info[] = {
	HWMON_CHANNEL_INFO(chip,
			   HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL),
	HWMON_CHANNEL_INFO(temp,
			   HWMON_T_INPUT | HWMON_T_TYPE | HWMON_T_LABEL |
			   HWMON_T_OFFSET),
	HWMON_CHANNEL_INFO(in,
			   HWMON_I_INPUT | HWMON_I_LABEL,
			   HWMON_I_INPUT | HWMON_I_LABEL,
			   HWMON_I_INPUT | HWMON_I_LABEL,
			   HWMON_I_INPUT | HWMON_I_LABEL),
	NULL
};

#endif /* !CONFIG_SENSORS_BT1_PVT_ALARMS */

static inline bool pvt_hwmon_channel_is_valid(enum hwmon_sensor_types type,
					      int ch)
{
	switch (type) {
	case hwmon_temp:
		if (ch < 0 || ch >= PVT_TEMP_CHS)
			return false;
		break;
	case hwmon_in:
		if (ch < 0 || ch >= PVT_VOLT_CHS)
			return false;
		break;
	default:
		break;
	}

	/* The rest of the types are independent from the channel number. */
	return true;
}

static umode_t pvt_hwmon_is_visible(const void *data,
				    enum hwmon_sensor_types type,
				    u32 attr, int ch)
{
	if (!pvt_hwmon_channel_is_valid(type, ch))
		return 0;

	switch (type) {
	case hwmon_chip:
		switch (attr) {
		case hwmon_chip_update_interval:
			return 0644;
		}
		break;
	case hwmon_temp:
		switch (attr) {
		case hwmon_temp_input:
		case hwmon_temp_type:
		case hwmon_temp_label:
			return 0444;
		case hwmon_temp_min:
		case hwmon_temp_max:
			return pvt_limit_is_visible(ch);
		case hwmon_temp_min_alarm:
		case hwmon_temp_max_alarm:
			return pvt_alarm_is_visible(ch);
		case hwmon_temp_offset:
			return 0644;
		}
		break;
	case hwmon_in:
		switch (attr) {
		case hwmon_in_input:
		case hwmon_in_label:
			return 0444;
		case hwmon_in_min:
		case hwmon_in_max:
			return pvt_limit_is_visible(PVT_VOLT + ch);
		case hwmon_in_min_alarm:
		case hwmon_in_max_alarm:
			return pvt_alarm_is_visible(PVT_VOLT + ch);
		}
		break;
	default:
		break;
	}

	return 0;
}

static int pvt_read_trim(struct pvt_hwmon *pvt, long *val)
{
	u32 data;

	data = readl(pvt->regs + PVT_CTRL);
	*val = FIELD_GET(PVT_CTRL_TRIM_MASK, data) * PVT_TRIM_STEP;

	return 0;
}

static int pvt_write_trim(struct pvt_hwmon *pvt, long val)
{
	u32 trim;
	int ret;

	/*
	 * Serialize trim update, since a part of the register is changed and
	 * the controller is supposed to be disabled during this operation.
	 */
	ret = mutex_lock_interruptible(&pvt->iface_mtx);
	if (ret)
		return ret;

	trim = pvt_calc_trim(val);
	pvt_set_trim(pvt, trim);

	mutex_unlock(&pvt->iface_mtx);

	return 0;
}

static int pvt_read_timeout(struct pvt_hwmon *pvt, long *val)
{
	unsigned long rate;
	ktime_t kt;
	u32 data;

	rate = clk_get_rate(pvt->clks[PVT_CLOCK_REF].clk);
	if (!rate)
		return -ENODEV;

	/*
	 * Don't bother with mutex here, since we just read data from MMIO.
	 * We also have to scale the ticks timeout up to compensate the
	 * ms-ns-data translations.
	 */
	data = readl(pvt->regs + PVT_TTIMEOUT) + 1;

	/*
	 * Calculate ref-clock based delay (Ttotal) between two consecutive
	 * data samples of the same sensor. So we first must calculate the
	 * delay introduced by the internal ref-clock timer (Tref * Fclk).
	 * Then add the constant timeout cuased by each conversion latency
	 * (Tmin). The basic formulae for each conversion is following:
	 *   Ttotal = Tref * Fclk + Tmin
	 * Note if alarms are enabled the sensors are polled one after
	 * another, so in order to have the delay being applicable for each
	 * sensor the requested value must be equally redistirbuted.
	 */
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
	kt = ktime_set(PVT_SENSORS_NUM * (u64)data, 0);
	kt = ktime_divns(kt, rate);
	kt = ktime_add_ns(kt, PVT_SENSORS_NUM * PVT_TOUT_MIN);
#else
	kt = ktime_set(data, 0);
	kt = ktime_divns(kt, rate);
	kt = ktime_add_ns(kt, PVT_TOUT_MIN);
#endif

	/* Return the result in msec as hwmon sysfs interface requires. */
	*val = ktime_to_ms(kt);

	return 0;
}

static int pvt_write_timeout(struct pvt_hwmon *pvt, long val)
{
	unsigned long rate;
	ktime_t kt;
	u32 data;
	int ret;

	rate = clk_get_rate(pvt->clks[PVT_CLOCK_REF].clk);
	if (!rate)
		return -ENODEV;

	/*
	 * If alarms are enabled, the requested timeout must be divided
	 * between all available sensors to have the requested delay
	 * applicable to each individual sensor.
	 */
	kt = ms_to_ktime(val);
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
	kt = ktime_divns(kt, PVT_SENSORS_NUM);
#endif

	/*
	 * Subtract a constant lag, which always persists due to the limited
	 * PVT sampling rate. Make sure the timeout is not negative.
	 */
	kt = ktime_sub_ns(kt, PVT_TOUT_MIN);
	if (ktime_to_ns(kt) < 0)
		kt = ktime_set(0, 0);

	/*
	 * Finally recalculate the timeout in terms of the reference clock
	 * period.
	 */
	data = ktime_divns(kt * rate, NSEC_PER_SEC);

	/*
	 * Update the measurements delay, but lock the interface first, since
	 * we have to disable PVT in order to have the new delay actually
	 * updated.
	 */
	ret = mutex_lock_interruptible(&pvt->iface_mtx);
	if (ret)
		return ret;

	pvt_set_tout(pvt, data);

	mutex_unlock(&pvt->iface_mtx);

	return 0;
}

static int pvt_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
			  u32 attr, int ch, long *val)
{
	struct pvt_hwmon *pvt = dev_get_drvdata(dev);

	if (!pvt_hwmon_channel_is_valid(type, ch))
		return -EINVAL;

	switch (type) {
	case hwmon_chip:
		switch (attr) {
		case hwmon_chip_update_interval:
			return pvt_read_timeout(pvt, val);
		}
		break;
	case hwmon_temp:
		switch (attr) {
		case hwmon_temp_input:
			return pvt_read_data(pvt, ch, val);
		case hwmon_temp_type:
			*val = 1;
			return 0;
		case hwmon_temp_min:
			return pvt_read_limit(pvt, ch, true, val);
		case hwmon_temp_max:
			return pvt_read_limit(pvt, ch, false, val);
		case hwmon_temp_min_alarm:
			return pvt_read_alarm(pvt, ch, true, val);
		case hwmon_temp_max_alarm:
			return pvt_read_alarm(pvt, ch, false, val);
		case hwmon_temp_offset:
			return pvt_read_trim(pvt, val);
		}
		break;
	case hwmon_in:
		switch (attr) {
		case hwmon_in_input:
			return pvt_read_data(pvt, PVT_VOLT + ch, val);
		case hwmon_in_min:
			return pvt_read_limit(pvt, PVT_VOLT + ch, true, val);
		case hwmon_in_max:
			return pvt_read_limit(pvt, PVT_VOLT + ch, false, val);
		case hwmon_in_min_alarm:
			return pvt_read_alarm(pvt, PVT_VOLT + ch, true, val);
		case hwmon_in_max_alarm:
			return pvt_read_alarm(pvt, PVT_VOLT + ch, false, val);
		}
		break;
	default:
		break;
	}

	return -EOPNOTSUPP;
}

static int pvt_hwmon_read_string(struct device *dev,
				 enum hwmon_sensor_types type,
				 u32 attr, int ch, const char **str)
{
	if (!pvt_hwmon_channel_is_valid(type, ch))
		return -EINVAL;

	switch (type) {
	case hwmon_temp:
		switch (attr) {
		case hwmon_temp_label:
			*str = pvt_info[ch].label;
			return 0;
		}
		break;
	case hwmon_in:
		switch (attr) {
		case hwmon_in_label:
			*str = pvt_info[PVT_VOLT + ch].label;
			return 0;
		}
		break;
	default:
		break;
	}

	return -EOPNOTSUPP;
}

static int pvt_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
			   u32 attr, int ch, long val)
{
	struct pvt_hwmon *pvt = dev_get_drvdata(dev);

	if (!pvt_hwmon_channel_is_valid(type, ch))
		return -EINVAL;

	switch (type) {
	case hwmon_chip:
		switch (attr) {
		case hwmon_chip_update_interval:
			return pvt_write_timeout(pvt, val);
		}
		break;
	case hwmon_temp:
		switch (attr) {
		case hwmon_temp_min:
			return pvt_write_limit(pvt, ch, true, val);
		case hwmon_temp_max:
			return pvt_write_limit(pvt, ch, false, val);
		case hwmon_temp_offset:
			return pvt_write_trim(pvt, val);
		}
		break;
	case hwmon_in:
		switch (attr) {
		case hwmon_in_min:
			return pvt_write_limit(pvt, PVT_VOLT + ch, true, val);
		case hwmon_in_max:
			return pvt_write_limit(pvt, PVT_VOLT + ch, false, val);
		}
		break;
	default:
		break;
	}

	return -EOPNOTSUPP;
}

static const struct hwmon_ops pvt_hwmon_ops = {
	.is_visible = pvt_hwmon_is_visible,
	.read = pvt_hwmon_read,
	.read_string = pvt_hwmon_read_string,
	.write = pvt_hwmon_write
};

static const struct hwmon_chip_info pvt_hwmon_info = {
	.ops = &pvt_hwmon_ops,
	.info = pvt_channel_info
};

static void pvt_clear_data(void *data)
{
	struct pvt_hwmon *pvt = data;
#if !defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
	int idx;

	for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
		complete_all(&pvt->cache[idx].conversion);
#endif

	mutex_destroy(&pvt->iface_mtx);
}

static struct pvt_hwmon *pvt_create_data(struct platform_device *pdev)
{
	struct device *dev = &pdev->dev;
	struct pvt_hwmon *pvt;
	int ret, idx;

	pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL);
	if (!pvt)
		return ERR_PTR(-ENOMEM);

	ret = devm_add_action(dev, pvt_clear_data, pvt);
	if (ret) {
		dev_err(dev, "Can't add PVT data clear action\n");
		return ERR_PTR(ret);
	}

	pvt->dev = dev;
	pvt->sensor = PVT_SENSOR_FIRST;
	mutex_init(&pvt->iface_mtx);

#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
	for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
		seqlock_init(&pvt->cache[idx].data_seqlock);
#else
	for (idx = 0; idx < PVT_SENSORS_NUM; ++idx)
		init_completion(&pvt->cache[idx].conversion);
#endif

	return pvt;
}

static int pvt_request_regs(struct pvt_hwmon *pvt)
{
	struct platform_device *pdev = to_platform_device(pvt->dev);
	struct resource *res;

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!res) {
		dev_err(pvt->dev, "Couldn't find PVT memresource\n");
		return -EINVAL;
	}

	pvt->regs = devm_ioremap_resource(pvt->dev, res);
	if (IS_ERR(pvt->regs)) {
		dev_err(pvt->dev, "Couldn't map PVT registers\n");
		return PTR_ERR(pvt->regs);
	}

	return 0;
}

static void pvt_disable_clks(void *data)
{
	struct pvt_hwmon *pvt = data;

	clk_bulk_disable_unprepare(PVT_CLOCK_NUM, pvt->clks);
}

static int pvt_request_clks(struct pvt_hwmon *pvt)
{
	int ret;

	pvt->clks[PVT_CLOCK_APB].id = "pclk";
	pvt->clks[PVT_CLOCK_REF].id = "ref";

	ret = devm_clk_bulk_get(pvt->dev, PVT_CLOCK_NUM, pvt->clks);
	if (ret) {
		dev_err(pvt->dev, "Couldn't get PVT clocks descriptors\n");
		return ret;
	}

	ret = clk_bulk_prepare_enable(PVT_CLOCK_NUM, pvt->clks);
	if (ret) {
		dev_err(pvt->dev, "Couldn't enable the PVT clocks\n");
		return ret;
	}

	ret = devm_add_action_or_reset(pvt->dev, pvt_disable_clks, pvt);
	if (ret) {
		dev_err(pvt->dev, "Can't add PVT clocks disable action\n");
		return ret;
	}

	return 0;
}

static void pvt_init_iface(struct pvt_hwmon *pvt)
{
	u32 trim, temp;

	/*
	 * Make sure all interrupts and controller are disabled so not to
	 * accidentally have ISR executed before the driver data is fully
	 * initialized. Clear the IRQ status as well.
	 */
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_ALL, PVT_INTR_ALL);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	readl(pvt->regs + PVT_CLR_INTR);
	readl(pvt->regs + PVT_DATA);

	/* Setup default sensor mode, timeout and temperature trim. */
	pvt_set_mode(pvt, pvt_info[pvt->sensor].mode);
	pvt_set_tout(pvt, PVT_TOUT_DEF);

	trim = PVT_TRIM_DEF;
	if (!of_property_read_u32(pvt->dev->of_node,
	     "baikal,pvt-temp-offset-millicelsius", &temp))
		trim = pvt_calc_trim(temp);

	pvt_set_trim(pvt, trim);
}

static int pvt_request_irq(struct pvt_hwmon *pvt)
{
	struct platform_device *pdev = to_platform_device(pvt->dev);
	int ret;

	pvt->irq = platform_get_irq(pdev, 0);
	if (pvt->irq < 0)
		return pvt->irq;

	ret = devm_request_threaded_irq(pvt->dev, pvt->irq,
					pvt_hard_isr, pvt_soft_isr,
#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)
					IRQF_SHARED | IRQF_TRIGGER_HIGH |
					IRQF_ONESHOT,
#else
					IRQF_SHARED | IRQF_TRIGGER_HIGH,
#endif
					"pvt", pvt);
	if (ret) {
		dev_err(pvt->dev, "Couldn't request PVT IRQ\n");
		return ret;
	}

	return 0;
}

static int pvt_create_hwmon(struct pvt_hwmon *pvt)
{
	pvt->hwmon = devm_hwmon_device_register_with_info(pvt->dev, "pvt", pvt,
		&pvt_hwmon_info, NULL);
	if (IS_ERR(pvt->hwmon)) {
		dev_err(pvt->dev, "Couldn't create hwmon device\n");
		return PTR_ERR(pvt->hwmon);
	}

	return 0;
}

#if defined(CONFIG_SENSORS_BT1_PVT_ALARMS)

static void pvt_disable_iface(void *data)
{
	struct pvt_hwmon *pvt = data;

	mutex_lock(&pvt->iface_mtx);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, 0);
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID,
		   PVT_INTR_DVALID);
	mutex_unlock(&pvt->iface_mtx);
}

static int pvt_enable_iface(struct pvt_hwmon *pvt)
{
	int ret;

	ret = devm_add_action(pvt->dev, pvt_disable_iface, pvt);
	if (ret) {
		dev_err(pvt->dev, "Can't add PVT disable interface action\n");
		return ret;
	}

	/*
	 * Enable sensors data conversion and IRQ. We need to lock the
	 * interface mutex since hwmon has just been created and the
	 * corresponding sysfs files are accessible from user-space,
	 * which theoretically may cause races.
	 */
	mutex_lock(&pvt->iface_mtx);
	pvt_update(pvt->regs + PVT_INTR_MASK, PVT_INTR_DVALID, 0);
	pvt_update(pvt->regs + PVT_CTRL, PVT_CTRL_EN, PVT_CTRL_EN);
	mutex_unlock(&pvt->iface_mtx);

	return 0;
}

#else /* !CONFIG_SENSORS_BT1_PVT_ALARMS */

static int pvt_enable_iface(struct pvt_hwmon *pvt)
{
	return 0;
}

#endif /* !CONFIG_SENSORS_BT1_PVT_ALARMS */

static int pvt_probe(struct platform_device *pdev)
{
	struct pvt_hwmon *pvt;
	int ret;

	pvt = pvt_create_data(pdev);
	if (IS_ERR(pvt))
		return PTR_ERR(pvt);

	ret = pvt_request_regs(pvt);
	if (ret)
		return ret;

	ret = pvt_request_clks(pvt);
	if (ret)
		return ret;

	pvt_init_iface(pvt);

	ret = pvt_request_irq(pvt);
	if (ret)
		return ret;

	ret = pvt_create_hwmon(pvt);
	if (ret)
		return ret;

	ret = pvt_enable_iface(pvt);
	if (ret)
		return ret;

	return 0;
}

static const struct of_device_id pvt_of_match[] = {
	{ .compatible = "baikal,bt1-pvt" },
	{ }
};
MODULE_DEVICE_TABLE(of, pvt_of_match);

static struct platform_driver pvt_driver = {
	.probe = pvt_probe,
	.driver = {
		.name = "bt1-pvt",
		.of_match_table = pvt_of_match
	}
};
module_platform_driver(pvt_driver);

MODULE_AUTHOR("Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>");
MODULE_DESCRIPTION("Baikal-T1 PVT driver");
MODULE_LICENSE("GPL v2");