1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * adm1021.c - Part of lm_sensors, Linux kernel modules for hardware 4 * monitoring 5 * Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl> and 6 * Philip Edelbrock <phil@netroedge.com> 7 */ 8 9 #include <linux/module.h> 10 #include <linux/init.h> 11 #include <linux/slab.h> 12 #include <linux/jiffies.h> 13 #include <linux/i2c.h> 14 #include <linux/hwmon.h> 15 #include <linux/hwmon-sysfs.h> 16 #include <linux/err.h> 17 #include <linux/mutex.h> 18 19 20 /* Addresses to scan */ 21 static const unsigned short normal_i2c[] = { 22 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; 23 24 enum chips { 25 adm1021, adm1023, max1617, max1617a, thmc10, lm84, gl523sm, mc1066 }; 26 27 /* adm1021 constants specified below */ 28 29 /* The adm1021 registers */ 30 /* Read-only */ 31 /* For nr in 0-1 */ 32 #define ADM1021_REG_TEMP(nr) (nr) 33 #define ADM1021_REG_STATUS 0x02 34 /* 0x41 = AD, 0x49 = TI, 0x4D = Maxim, 0x23 = Genesys , 0x54 = Onsemi */ 35 #define ADM1021_REG_MAN_ID 0xFE 36 /* ADM1021 = 0x0X, ADM1023 = 0x3X */ 37 #define ADM1021_REG_DEV_ID 0xFF 38 /* These use different addresses for reading/writing */ 39 #define ADM1021_REG_CONFIG_R 0x03 40 #define ADM1021_REG_CONFIG_W 0x09 41 #define ADM1021_REG_CONV_RATE_R 0x04 42 #define ADM1021_REG_CONV_RATE_W 0x0A 43 /* These are for the ADM1023's additional precision on the remote temp sensor */ 44 #define ADM1023_REG_REM_TEMP_PREC 0x10 45 #define ADM1023_REG_REM_OFFSET 0x11 46 #define ADM1023_REG_REM_OFFSET_PREC 0x12 47 #define ADM1023_REG_REM_TOS_PREC 0x13 48 #define ADM1023_REG_REM_THYST_PREC 0x14 49 /* limits */ 50 /* For nr in 0-1 */ 51 #define ADM1021_REG_TOS_R(nr) (0x05 + 2 * (nr)) 52 #define ADM1021_REG_TOS_W(nr) (0x0B + 2 * (nr)) 53 #define ADM1021_REG_THYST_R(nr) (0x06 + 2 * (nr)) 54 #define ADM1021_REG_THYST_W(nr) (0x0C + 2 * (nr)) 55 /* write-only */ 56 #define ADM1021_REG_ONESHOT 0x0F 57 58 /* Initial values */ 59 60 /* 61 * Note: Even though I left the low and high limits named os and hyst, 62 * they don't quite work like a thermostat the way the LM75 does. I.e., 63 * a lower temp than THYST actually triggers an alarm instead of 64 * clearing it. Weird, ey? --Phil 65 */ 66 67 /* Each client has this additional data */ 68 struct adm1021_data { 69 struct i2c_client *client; 70 enum chips type; 71 72 const struct attribute_group *groups[3]; 73 74 struct mutex update_lock; 75 char valid; /* !=0 if following fields are valid */ 76 char low_power; /* !=0 if device in low power mode */ 77 unsigned long last_updated; /* In jiffies */ 78 79 int temp_max[2]; /* Register values */ 80 int temp_min[2]; 81 int temp[2]; 82 u8 alarms; 83 /* Special values for ADM1023 only */ 84 u8 remote_temp_offset; 85 u8 remote_temp_offset_prec; 86 }; 87 88 /* (amalysh) read only mode, otherwise any limit's writing confuse BIOS */ 89 static bool read_only; 90 91 static struct adm1021_data *adm1021_update_device(struct device *dev) 92 { 93 struct adm1021_data *data = dev_get_drvdata(dev); 94 struct i2c_client *client = data->client; 95 96 mutex_lock(&data->update_lock); 97 98 if (time_after(jiffies, data->last_updated + HZ + HZ / 2) 99 || !data->valid) { 100 int i; 101 102 dev_dbg(dev, "Starting adm1021 update\n"); 103 104 for (i = 0; i < 2; i++) { 105 data->temp[i] = 1000 * 106 (s8) i2c_smbus_read_byte_data( 107 client, ADM1021_REG_TEMP(i)); 108 data->temp_max[i] = 1000 * 109 (s8) i2c_smbus_read_byte_data( 110 client, ADM1021_REG_TOS_R(i)); 111 if (data->type != lm84) { 112 data->temp_min[i] = 1000 * 113 (s8) i2c_smbus_read_byte_data(client, 114 ADM1021_REG_THYST_R(i)); 115 } 116 } 117 data->alarms = i2c_smbus_read_byte_data(client, 118 ADM1021_REG_STATUS) & 0x7c; 119 if (data->type == adm1023) { 120 /* 121 * The ADM1023 provides 3 extra bits of precision for 122 * the remote sensor in extra registers. 123 */ 124 data->temp[1] += 125 * (i2c_smbus_read_byte_data( 125 client, ADM1023_REG_REM_TEMP_PREC) >> 5); 126 data->temp_max[1] += 125 * (i2c_smbus_read_byte_data( 127 client, ADM1023_REG_REM_TOS_PREC) >> 5); 128 data->temp_min[1] += 125 * (i2c_smbus_read_byte_data( 129 client, ADM1023_REG_REM_THYST_PREC) >> 5); 130 data->remote_temp_offset = 131 i2c_smbus_read_byte_data(client, 132 ADM1023_REG_REM_OFFSET); 133 data->remote_temp_offset_prec = 134 i2c_smbus_read_byte_data(client, 135 ADM1023_REG_REM_OFFSET_PREC); 136 } 137 data->last_updated = jiffies; 138 data->valid = 1; 139 } 140 141 mutex_unlock(&data->update_lock); 142 143 return data; 144 } 145 146 static ssize_t temp_show(struct device *dev, struct device_attribute *devattr, 147 char *buf) 148 { 149 int index = to_sensor_dev_attr(devattr)->index; 150 struct adm1021_data *data = adm1021_update_device(dev); 151 152 return sprintf(buf, "%d\n", data->temp[index]); 153 } 154 155 static ssize_t temp_max_show(struct device *dev, 156 struct device_attribute *devattr, char *buf) 157 { 158 int index = to_sensor_dev_attr(devattr)->index; 159 struct adm1021_data *data = adm1021_update_device(dev); 160 161 return sprintf(buf, "%d\n", data->temp_max[index]); 162 } 163 164 static ssize_t temp_min_show(struct device *dev, 165 struct device_attribute *devattr, char *buf) 166 { 167 int index = to_sensor_dev_attr(devattr)->index; 168 struct adm1021_data *data = adm1021_update_device(dev); 169 170 return sprintf(buf, "%d\n", data->temp_min[index]); 171 } 172 173 static ssize_t alarm_show(struct device *dev, struct device_attribute *attr, 174 char *buf) 175 { 176 int index = to_sensor_dev_attr(attr)->index; 177 struct adm1021_data *data = adm1021_update_device(dev); 178 return sprintf(buf, "%u\n", (data->alarms >> index) & 1); 179 } 180 181 static ssize_t alarms_show(struct device *dev, 182 struct device_attribute *attr, 183 char *buf) 184 { 185 struct adm1021_data *data = adm1021_update_device(dev); 186 return sprintf(buf, "%u\n", data->alarms); 187 } 188 189 static ssize_t temp_max_store(struct device *dev, 190 struct device_attribute *devattr, 191 const char *buf, size_t count) 192 { 193 int index = to_sensor_dev_attr(devattr)->index; 194 struct adm1021_data *data = dev_get_drvdata(dev); 195 struct i2c_client *client = data->client; 196 long temp; 197 int reg_val, err; 198 199 err = kstrtol(buf, 10, &temp); 200 if (err) 201 return err; 202 temp /= 1000; 203 204 mutex_lock(&data->update_lock); 205 reg_val = clamp_val(temp, -128, 127); 206 data->temp_max[index] = reg_val * 1000; 207 if (!read_only) 208 i2c_smbus_write_byte_data(client, ADM1021_REG_TOS_W(index), 209 reg_val); 210 mutex_unlock(&data->update_lock); 211 212 return count; 213 } 214 215 static ssize_t temp_min_store(struct device *dev, 216 struct device_attribute *devattr, 217 const char *buf, size_t count) 218 { 219 int index = to_sensor_dev_attr(devattr)->index; 220 struct adm1021_data *data = dev_get_drvdata(dev); 221 struct i2c_client *client = data->client; 222 long temp; 223 int reg_val, err; 224 225 err = kstrtol(buf, 10, &temp); 226 if (err) 227 return err; 228 temp /= 1000; 229 230 mutex_lock(&data->update_lock); 231 reg_val = clamp_val(temp, -128, 127); 232 data->temp_min[index] = reg_val * 1000; 233 if (!read_only) 234 i2c_smbus_write_byte_data(client, ADM1021_REG_THYST_W(index), 235 reg_val); 236 mutex_unlock(&data->update_lock); 237 238 return count; 239 } 240 241 static ssize_t low_power_show(struct device *dev, 242 struct device_attribute *devattr, char *buf) 243 { 244 struct adm1021_data *data = adm1021_update_device(dev); 245 return sprintf(buf, "%d\n", data->low_power); 246 } 247 248 static ssize_t low_power_store(struct device *dev, 249 struct device_attribute *devattr, 250 const char *buf, size_t count) 251 { 252 struct adm1021_data *data = dev_get_drvdata(dev); 253 struct i2c_client *client = data->client; 254 char low_power; 255 unsigned long val; 256 int err; 257 258 err = kstrtoul(buf, 10, &val); 259 if (err) 260 return err; 261 low_power = val != 0; 262 263 mutex_lock(&data->update_lock); 264 if (low_power != data->low_power) { 265 int config = i2c_smbus_read_byte_data( 266 client, ADM1021_REG_CONFIG_R); 267 data->low_power = low_power; 268 i2c_smbus_write_byte_data(client, ADM1021_REG_CONFIG_W, 269 (config & 0xBF) | (low_power << 6)); 270 } 271 mutex_unlock(&data->update_lock); 272 273 return count; 274 } 275 276 277 static SENSOR_DEVICE_ATTR_RO(temp1_input, temp, 0); 278 static SENSOR_DEVICE_ATTR_RW(temp1_max, temp_max, 0); 279 static SENSOR_DEVICE_ATTR_RW(temp1_min, temp_min, 0); 280 static SENSOR_DEVICE_ATTR_RO(temp2_input, temp, 1); 281 static SENSOR_DEVICE_ATTR_RW(temp2_max, temp_max, 1); 282 static SENSOR_DEVICE_ATTR_RW(temp2_min, temp_min, 1); 283 static SENSOR_DEVICE_ATTR_RO(temp1_max_alarm, alarm, 6); 284 static SENSOR_DEVICE_ATTR_RO(temp1_min_alarm, alarm, 5); 285 static SENSOR_DEVICE_ATTR_RO(temp2_max_alarm, alarm, 4); 286 static SENSOR_DEVICE_ATTR_RO(temp2_min_alarm, alarm, 3); 287 static SENSOR_DEVICE_ATTR_RO(temp2_fault, alarm, 2); 288 289 static DEVICE_ATTR_RO(alarms); 290 static DEVICE_ATTR_RW(low_power); 291 292 static struct attribute *adm1021_attributes[] = { 293 &sensor_dev_attr_temp1_max.dev_attr.attr, 294 &sensor_dev_attr_temp1_input.dev_attr.attr, 295 &sensor_dev_attr_temp2_max.dev_attr.attr, 296 &sensor_dev_attr_temp2_input.dev_attr.attr, 297 &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, 298 &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, 299 &sensor_dev_attr_temp2_fault.dev_attr.attr, 300 &dev_attr_alarms.attr, 301 &dev_attr_low_power.attr, 302 NULL 303 }; 304 305 static const struct attribute_group adm1021_group = { 306 .attrs = adm1021_attributes, 307 }; 308 309 static struct attribute *adm1021_min_attributes[] = { 310 &sensor_dev_attr_temp1_min.dev_attr.attr, 311 &sensor_dev_attr_temp2_min.dev_attr.attr, 312 &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, 313 &sensor_dev_attr_temp2_min_alarm.dev_attr.attr, 314 NULL 315 }; 316 317 static const struct attribute_group adm1021_min_group = { 318 .attrs = adm1021_min_attributes, 319 }; 320 321 /* Return 0 if detection is successful, -ENODEV otherwise */ 322 static int adm1021_detect(struct i2c_client *client, 323 struct i2c_board_info *info) 324 { 325 struct i2c_adapter *adapter = client->adapter; 326 const char *type_name; 327 int conv_rate, status, config, man_id, dev_id; 328 329 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { 330 pr_debug("detect failed, smbus byte data not supported!\n"); 331 return -ENODEV; 332 } 333 334 status = i2c_smbus_read_byte_data(client, ADM1021_REG_STATUS); 335 conv_rate = i2c_smbus_read_byte_data(client, 336 ADM1021_REG_CONV_RATE_R); 337 config = i2c_smbus_read_byte_data(client, ADM1021_REG_CONFIG_R); 338 339 /* Check unused bits */ 340 if ((status & 0x03) || (config & 0x3F) || (conv_rate & 0xF8)) { 341 pr_debug("detect failed, chip not detected!\n"); 342 return -ENODEV; 343 } 344 345 /* Determine the chip type. */ 346 man_id = i2c_smbus_read_byte_data(client, ADM1021_REG_MAN_ID); 347 dev_id = i2c_smbus_read_byte_data(client, ADM1021_REG_DEV_ID); 348 349 if (man_id < 0 || dev_id < 0) 350 return -ENODEV; 351 352 if (man_id == 0x4d && dev_id == 0x01) 353 type_name = "max1617a"; 354 else if (man_id == 0x41) { 355 if ((dev_id & 0xF0) == 0x30) 356 type_name = "adm1023"; 357 else if ((dev_id & 0xF0) == 0x00) 358 type_name = "adm1021"; 359 else 360 return -ENODEV; 361 } else if (man_id == 0x49) 362 type_name = "thmc10"; 363 else if (man_id == 0x23) 364 type_name = "gl523sm"; 365 else if (man_id == 0x54) 366 type_name = "mc1066"; 367 else { 368 int lte, rte, lhi, rhi, llo, rlo; 369 370 /* extra checks for LM84 and MAX1617 to avoid misdetections */ 371 372 llo = i2c_smbus_read_byte_data(client, ADM1021_REG_THYST_R(0)); 373 rlo = i2c_smbus_read_byte_data(client, ADM1021_REG_THYST_R(1)); 374 375 /* fail if any of the additional register reads failed */ 376 if (llo < 0 || rlo < 0) 377 return -ENODEV; 378 379 lte = i2c_smbus_read_byte_data(client, ADM1021_REG_TEMP(0)); 380 rte = i2c_smbus_read_byte_data(client, ADM1021_REG_TEMP(1)); 381 lhi = i2c_smbus_read_byte_data(client, ADM1021_REG_TOS_R(0)); 382 rhi = i2c_smbus_read_byte_data(client, ADM1021_REG_TOS_R(1)); 383 384 /* 385 * Fail for negative temperatures and negative high limits. 386 * This check also catches read errors on the tested registers. 387 */ 388 if ((s8)lte < 0 || (s8)rte < 0 || (s8)lhi < 0 || (s8)rhi < 0) 389 return -ENODEV; 390 391 /* fail if all registers hold the same value */ 392 if (lte == rte && lte == lhi && lte == rhi && lte == llo 393 && lte == rlo) 394 return -ENODEV; 395 396 /* 397 * LM84 Mfr ID is in a different place, 398 * and it has more unused bits. 399 */ 400 if (conv_rate == 0x00 401 && (config & 0x7F) == 0x00 402 && (status & 0xAB) == 0x00) { 403 type_name = "lm84"; 404 } else { 405 /* fail if low limits are larger than high limits */ 406 if ((s8)llo > lhi || (s8)rlo > rhi) 407 return -ENODEV; 408 type_name = "max1617"; 409 } 410 } 411 412 pr_debug("Detected chip %s at adapter %d, address 0x%02x.\n", 413 type_name, i2c_adapter_id(adapter), client->addr); 414 strlcpy(info->type, type_name, I2C_NAME_SIZE); 415 416 return 0; 417 } 418 419 static void adm1021_init_client(struct i2c_client *client) 420 { 421 /* Enable ADC and disable suspend mode */ 422 i2c_smbus_write_byte_data(client, ADM1021_REG_CONFIG_W, 423 i2c_smbus_read_byte_data(client, ADM1021_REG_CONFIG_R) & 0xBF); 424 /* Set Conversion rate to 1/sec (this can be tinkered with) */ 425 i2c_smbus_write_byte_data(client, ADM1021_REG_CONV_RATE_W, 0x04); 426 } 427 428 static int adm1021_probe(struct i2c_client *client, 429 const struct i2c_device_id *id) 430 { 431 struct device *dev = &client->dev; 432 struct adm1021_data *data; 433 struct device *hwmon_dev; 434 435 data = devm_kzalloc(dev, sizeof(struct adm1021_data), GFP_KERNEL); 436 if (!data) 437 return -ENOMEM; 438 439 data->client = client; 440 data->type = id->driver_data; 441 mutex_init(&data->update_lock); 442 443 /* Initialize the ADM1021 chip */ 444 if (data->type != lm84 && !read_only) 445 adm1021_init_client(client); 446 447 data->groups[0] = &adm1021_group; 448 if (data->type != lm84) 449 data->groups[1] = &adm1021_min_group; 450 451 hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name, 452 data, data->groups); 453 454 return PTR_ERR_OR_ZERO(hwmon_dev); 455 } 456 457 static const struct i2c_device_id adm1021_id[] = { 458 { "adm1021", adm1021 }, 459 { "adm1023", adm1023 }, 460 { "max1617", max1617 }, 461 { "max1617a", max1617a }, 462 { "thmc10", thmc10 }, 463 { "lm84", lm84 }, 464 { "gl523sm", gl523sm }, 465 { "mc1066", mc1066 }, 466 { } 467 }; 468 MODULE_DEVICE_TABLE(i2c, adm1021_id); 469 470 static struct i2c_driver adm1021_driver = { 471 .class = I2C_CLASS_HWMON, 472 .driver = { 473 .name = "adm1021", 474 }, 475 .probe = adm1021_probe, 476 .id_table = adm1021_id, 477 .detect = adm1021_detect, 478 .address_list = normal_i2c, 479 }; 480 481 module_i2c_driver(adm1021_driver); 482 483 MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl> and " 484 "Philip Edelbrock <phil@netroedge.com>"); 485 MODULE_DESCRIPTION("adm1021 driver"); 486 MODULE_LICENSE("GPL"); 487 488 module_param(read_only, bool, 0); 489 MODULE_PARM_DESC(read_only, "Don't set any values, read only mode"); 490