1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * abituguru3.c 4 * 5 * Copyright (c) 2006-2008 Hans de Goede <hdegoede@redhat.com> 6 * Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk> 7 */ 8 /* 9 * This driver supports the sensor part of revision 3 of the custom Abit uGuru 10 * chip found on newer Abit uGuru motherboards. Note: because of lack of specs 11 * only reading the sensors and their settings is supported. 12 */ 13 14 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 15 16 #include <linux/module.h> 17 #include <linux/init.h> 18 #include <linux/slab.h> 19 #include <linux/jiffies.h> 20 #include <linux/mutex.h> 21 #include <linux/err.h> 22 #include <linux/delay.h> 23 #include <linux/platform_device.h> 24 #include <linux/hwmon.h> 25 #include <linux/hwmon-sysfs.h> 26 #include <linux/dmi.h> 27 #include <linux/io.h> 28 29 /* uGuru3 bank addresses */ 30 #define ABIT_UGURU3_SETTINGS_BANK 0x01 31 #define ABIT_UGURU3_SENSORS_BANK 0x08 32 #define ABIT_UGURU3_MISC_BANK 0x09 33 #define ABIT_UGURU3_ALARMS_START 0x1E 34 #define ABIT_UGURU3_SETTINGS_START 0x24 35 #define ABIT_UGURU3_VALUES_START 0x80 36 #define ABIT_UGURU3_BOARD_ID 0x0A 37 /* uGuru3 sensor bank flags */ /* Alarm if: */ 38 #define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */ 39 #define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */ 40 #define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */ 41 #define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */ 42 #define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */ 43 #define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */ 44 #define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */ 45 #define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */ 46 #define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */ 47 /* sensor types */ 48 #define ABIT_UGURU3_IN_SENSOR 0 49 #define ABIT_UGURU3_TEMP_SENSOR 1 50 #define ABIT_UGURU3_FAN_SENSOR 2 51 52 /* 53 * Timeouts / Retries, if these turn out to need a lot of fiddling we could 54 * convert them to params. Determined by trial and error. I assume this is 55 * cpu-speed independent, since the ISA-bus and not the CPU should be the 56 * bottleneck. 57 */ 58 #define ABIT_UGURU3_WAIT_TIMEOUT 250 59 /* 60 * Normally the 0xAC at the end of synchronize() is reported after the 61 * first read, but sometimes not and we need to poll 62 */ 63 #define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5 64 /* utility macros */ 65 #define ABIT_UGURU3_NAME "abituguru3" 66 #define ABIT_UGURU3_DEBUG(format, arg...) \ 67 do { \ 68 if (verbose) \ 69 pr_debug(format , ## arg); \ 70 } while (0) 71 72 /* Macros to help calculate the sysfs_names array length */ 73 #define ABIT_UGURU3_MAX_NO_SENSORS 26 74 /* 75 * sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0, 76 * in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 77 */ 78 #define ABIT_UGURU3_IN_NAMES_LENGTH \ 79 (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11) 80 /* 81 * sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0, 82 * temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0, 83 * temp??_label\0 84 */ 85 #define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13) 86 /* 87 * sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0, 88 * fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 89 */ 90 #define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12) 91 /* 92 * Worst case scenario 16 in sensors (longest names_length) and the rest 93 * temp sensors (second longest names_length). 94 */ 95 #define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \ 96 (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH) 97 98 /* 99 * All the macros below are named identical to the openguru2 program 100 * reverse engineered by Louis Kruger, hence the names might not be 100% 101 * logical. I could come up with better names, but I prefer keeping the names 102 * identical so that this driver can be compared with his work more easily. 103 */ 104 /* Two i/o-ports are used by uGuru */ 105 #define ABIT_UGURU3_BASE 0x00E0 106 #define ABIT_UGURU3_CMD 0x00 107 #define ABIT_UGURU3_DATA 0x04 108 #define ABIT_UGURU3_REGION_LENGTH 5 109 /* 110 * The wait_xxx functions return this on success and the last contents 111 * of the DATA register (0-255) on failure. 112 */ 113 #define ABIT_UGURU3_SUCCESS -1 114 /* uGuru status flags */ 115 #define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01 116 #define ABIT_UGURU3_STATUS_BUSY 0x02 117 118 119 /* Structures */ 120 struct abituguru3_sensor_info { 121 const char *name; 122 int port; 123 int type; 124 int multiplier; 125 int divisor; 126 int offset; 127 }; 128 129 /* Avoid use of flexible array members */ 130 #define ABIT_UGURU3_MAX_DMI_NAMES 2 131 132 struct abituguru3_motherboard_info { 133 u16 id; 134 const char *dmi_name[ABIT_UGURU3_MAX_DMI_NAMES + 1]; 135 /* + 1 -> end of sensors indicated by a sensor with name == NULL */ 136 struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; 137 }; 138 139 /* 140 * For the Abit uGuru, we need to keep some data in memory. 141 * The structure is dynamically allocated, at the same time when a new 142 * abituguru3 device is allocated. 143 */ 144 struct abituguru3_data { 145 struct device *hwmon_dev; /* hwmon registered device */ 146 struct mutex update_lock; /* protect access to data and uGuru */ 147 unsigned short addr; /* uguru base address */ 148 bool valid; /* true if following fields are valid */ 149 unsigned long last_updated; /* In jiffies */ 150 151 /* 152 * For convenience the sysfs attr and their names are generated 153 * automatically. We have max 10 entries per sensor (for in sensors) 154 */ 155 struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS 156 * 10]; 157 158 /* Buffer to store the dynamically generated sysfs names */ 159 char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH]; 160 161 /* Pointer to the sensors info for the detected motherboard */ 162 const struct abituguru3_sensor_info *sensors; 163 164 /* 165 * The abituguru3 supports up to 48 sensors, and thus has registers 166 * sets for 48 sensors, for convenience reasons / simplicity of the 167 * code we always read and store all registers for all 48 sensors 168 */ 169 170 /* Alarms for all 48 sensors (1 bit per sensor) */ 171 u8 alarms[48/8]; 172 173 /* Value of all 48 sensors */ 174 u8 value[48]; 175 176 /* 177 * Settings of all 48 sensors, note in and temp sensors (the first 32 178 * sensors) have 3 bytes of settings, while fans only have 2 bytes, 179 * for convenience we use 3 bytes for all sensors 180 */ 181 u8 settings[48][3]; 182 }; 183 184 185 /* Constants */ 186 static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { 187 { 0x000C, { NULL } /* Unknown, need DMI string */, { 188 { "CPU Core", 0, 0, 10, 1, 0 }, 189 { "DDR", 1, 0, 10, 1, 0 }, 190 { "DDR VTT", 2, 0, 10, 1, 0 }, 191 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 192 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 193 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 194 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 195 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 196 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 197 { "ATX +5V", 9, 0, 30, 1, 0 }, 198 { "+3.3V", 10, 0, 20, 1, 0 }, 199 { "5VSB", 11, 0, 30, 1, 0 }, 200 { "CPU", 24, 1, 1, 1, 0 }, 201 { "System", 25, 1, 1, 1, 0 }, 202 { "PWM", 26, 1, 1, 1, 0 }, 203 { "CPU Fan", 32, 2, 60, 1, 0 }, 204 { "NB Fan", 33, 2, 60, 1, 0 }, 205 { "SYS FAN", 34, 2, 60, 1, 0 }, 206 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 207 { NULL, 0, 0, 0, 0, 0 } } 208 }, 209 { 0x000D, { NULL } /* Abit AW8, need DMI string */, { 210 { "CPU Core", 0, 0, 10, 1, 0 }, 211 { "DDR", 1, 0, 10, 1, 0 }, 212 { "DDR VTT", 2, 0, 10, 1, 0 }, 213 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 214 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 215 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 216 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 217 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 218 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 219 { "ATX +5V", 9, 0, 30, 1, 0 }, 220 { "+3.3V", 10, 0, 20, 1, 0 }, 221 { "5VSB", 11, 0, 30, 1, 0 }, 222 { "CPU", 24, 1, 1, 1, 0 }, 223 { "System", 25, 1, 1, 1, 0 }, 224 { "PWM1", 26, 1, 1, 1, 0 }, 225 { "PWM2", 27, 1, 1, 1, 0 }, 226 { "PWM3", 28, 1, 1, 1, 0 }, 227 { "PWM4", 29, 1, 1, 1, 0 }, 228 { "CPU Fan", 32, 2, 60, 1, 0 }, 229 { "NB Fan", 33, 2, 60, 1, 0 }, 230 { "SYS Fan", 34, 2, 60, 1, 0 }, 231 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 232 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 233 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 234 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 235 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 236 { NULL, 0, 0, 0, 0, 0 } } 237 }, 238 { 0x000E, { NULL } /* AL-8, need DMI string */, { 239 { "CPU Core", 0, 0, 10, 1, 0 }, 240 { "DDR", 1, 0, 10, 1, 0 }, 241 { "DDR VTT", 2, 0, 10, 1, 0 }, 242 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 243 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 244 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 245 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 246 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 247 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 248 { "ATX +5V", 9, 0, 30, 1, 0 }, 249 { "+3.3V", 10, 0, 20, 1, 0 }, 250 { "5VSB", 11, 0, 30, 1, 0 }, 251 { "CPU", 24, 1, 1, 1, 0 }, 252 { "System", 25, 1, 1, 1, 0 }, 253 { "PWM", 26, 1, 1, 1, 0 }, 254 { "CPU Fan", 32, 2, 60, 1, 0 }, 255 { "NB Fan", 33, 2, 60, 1, 0 }, 256 { "SYS Fan", 34, 2, 60, 1, 0 }, 257 { NULL, 0, 0, 0, 0, 0 } } 258 }, 259 { 0x000F, { NULL } /* Unknown, need DMI string */, { 260 261 { "CPU Core", 0, 0, 10, 1, 0 }, 262 { "DDR", 1, 0, 10, 1, 0 }, 263 { "DDR VTT", 2, 0, 10, 1, 0 }, 264 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 265 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 266 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 267 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 268 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 269 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 270 { "ATX +5V", 9, 0, 30, 1, 0 }, 271 { "+3.3V", 10, 0, 20, 1, 0 }, 272 { "5VSB", 11, 0, 30, 1, 0 }, 273 { "CPU", 24, 1, 1, 1, 0 }, 274 { "System", 25, 1, 1, 1, 0 }, 275 { "PWM", 26, 1, 1, 1, 0 }, 276 { "CPU Fan", 32, 2, 60, 1, 0 }, 277 { "NB Fan", 33, 2, 60, 1, 0 }, 278 { "SYS Fan", 34, 2, 60, 1, 0 }, 279 { NULL, 0, 0, 0, 0, 0 } } 280 }, 281 { 0x0010, { NULL } /* Abit NI8 SLI GR, need DMI string */, { 282 { "CPU Core", 0, 0, 10, 1, 0 }, 283 { "DDR", 1, 0, 10, 1, 0 }, 284 { "DDR VTT", 2, 0, 10, 1, 0 }, 285 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 286 { "NB 1.4V", 4, 0, 10, 1, 0 }, 287 { "SB 1.5V", 6, 0, 10, 1, 0 }, 288 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 289 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 290 { "ATX +5V", 9, 0, 30, 1, 0 }, 291 { "+3.3V", 10, 0, 20, 1, 0 }, 292 { "5VSB", 11, 0, 30, 1, 0 }, 293 { "CPU", 24, 1, 1, 1, 0 }, 294 { "SYS", 25, 1, 1, 1, 0 }, 295 { "PWM", 26, 1, 1, 1, 0 }, 296 { "CPU Fan", 32, 2, 60, 1, 0 }, 297 { "NB Fan", 33, 2, 60, 1, 0 }, 298 { "SYS Fan", 34, 2, 60, 1, 0 }, 299 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 300 { "OTES1 Fan", 36, 2, 60, 1, 0 }, 301 { NULL, 0, 0, 0, 0, 0 } } 302 }, 303 { 0x0011, { "AT8 32X", NULL }, { 304 { "CPU Core", 0, 0, 10, 1, 0 }, 305 { "DDR", 1, 0, 20, 1, 0 }, 306 { "DDR VTT", 2, 0, 10, 1, 0 }, 307 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 308 { "NB 1.8V", 4, 0, 10, 1, 0 }, 309 { "NB 1.8V Dual", 5, 0, 10, 1, 0 }, 310 { "HTV 1.2", 3, 0, 10, 1, 0 }, 311 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 312 { "NB 1.2V", 13, 0, 10, 1, 0 }, 313 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 314 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 315 { "ATX +5V", 9, 0, 30, 1, 0 }, 316 { "+3.3V", 10, 0, 20, 1, 0 }, 317 { "5VSB", 11, 0, 30, 1, 0 }, 318 { "CPU", 24, 1, 1, 1, 0 }, 319 { "NB", 25, 1, 1, 1, 0 }, 320 { "System", 26, 1, 1, 1, 0 }, 321 { "PWM", 27, 1, 1, 1, 0 }, 322 { "CPU Fan", 32, 2, 60, 1, 0 }, 323 { "NB Fan", 33, 2, 60, 1, 0 }, 324 { "SYS Fan", 34, 2, 60, 1, 0 }, 325 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 326 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 327 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 328 { NULL, 0, 0, 0, 0, 0 } } 329 }, 330 { 0x0012, { NULL } /* Abit AN8 32X, need DMI string */, { 331 { "CPU Core", 0, 0, 10, 1, 0 }, 332 { "DDR", 1, 0, 20, 1, 0 }, 333 { "DDR VTT", 2, 0, 10, 1, 0 }, 334 { "HyperTransport", 3, 0, 10, 1, 0 }, 335 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 336 { "NB", 4, 0, 10, 1, 0 }, 337 { "SB", 6, 0, 10, 1, 0 }, 338 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 339 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 340 { "ATX +5V", 9, 0, 30, 1, 0 }, 341 { "+3.3V", 10, 0, 20, 1, 0 }, 342 { "5VSB", 11, 0, 30, 1, 0 }, 343 { "CPU", 24, 1, 1, 1, 0 }, 344 { "SYS", 25, 1, 1, 1, 0 }, 345 { "PWM", 26, 1, 1, 1, 0 }, 346 { "CPU Fan", 32, 2, 60, 1, 0 }, 347 { "NB Fan", 33, 2, 60, 1, 0 }, 348 { "SYS Fan", 34, 2, 60, 1, 0 }, 349 { "AUX1 Fan", 36, 2, 60, 1, 0 }, 350 { NULL, 0, 0, 0, 0, 0 } } 351 }, 352 { 0x0013, { NULL } /* Abit AW8D, need DMI string */, { 353 { "CPU Core", 0, 0, 10, 1, 0 }, 354 { "DDR", 1, 0, 10, 1, 0 }, 355 { "DDR VTT", 2, 0, 10, 1, 0 }, 356 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 357 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 358 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 359 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 360 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 361 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 362 { "ATX +5V", 9, 0, 30, 1, 0 }, 363 { "+3.3V", 10, 0, 20, 1, 0 }, 364 { "5VSB", 11, 0, 30, 1, 0 }, 365 { "CPU", 24, 1, 1, 1, 0 }, 366 { "System", 25, 1, 1, 1, 0 }, 367 { "PWM1", 26, 1, 1, 1, 0 }, 368 { "PWM2", 27, 1, 1, 1, 0 }, 369 { "PWM3", 28, 1, 1, 1, 0 }, 370 { "PWM4", 29, 1, 1, 1, 0 }, 371 { "CPU Fan", 32, 2, 60, 1, 0 }, 372 { "NB Fan", 33, 2, 60, 1, 0 }, 373 { "SYS Fan", 34, 2, 60, 1, 0 }, 374 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 375 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 376 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 377 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 378 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 379 { NULL, 0, 0, 0, 0, 0 } } 380 }, 381 { 0x0014, { "AB9", "AB9 Pro", NULL }, { 382 { "CPU Core", 0, 0, 10, 1, 0 }, 383 { "DDR", 1, 0, 10, 1, 0 }, 384 { "DDR VTT", 2, 0, 10, 1, 0 }, 385 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 386 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 387 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 388 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 389 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 390 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 391 { "ATX +5V", 9, 0, 30, 1, 0 }, 392 { "+3.3V", 10, 0, 20, 1, 0 }, 393 { "5VSB", 11, 0, 30, 1, 0 }, 394 { "CPU", 24, 1, 1, 1, 0 }, 395 { "System", 25, 1, 1, 1, 0 }, 396 { "PWM", 26, 1, 1, 1, 0 }, 397 { "CPU Fan", 32, 2, 60, 1, 0 }, 398 { "NB Fan", 33, 2, 60, 1, 0 }, 399 { "SYS Fan", 34, 2, 60, 1, 0 }, 400 { NULL, 0, 0, 0, 0, 0 } } 401 }, 402 { 0x0015, { NULL } /* Unknown, need DMI string */, { 403 { "CPU Core", 0, 0, 10, 1, 0 }, 404 { "DDR", 1, 0, 20, 1, 0 }, 405 { "DDR VTT", 2, 0, 10, 1, 0 }, 406 { "HyperTransport", 3, 0, 10, 1, 0 }, 407 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 408 { "NB", 4, 0, 10, 1, 0 }, 409 { "SB", 6, 0, 10, 1, 0 }, 410 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 411 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 412 { "ATX +5V", 9, 0, 30, 1, 0 }, 413 { "+3.3V", 10, 0, 20, 1, 0 }, 414 { "5VSB", 11, 0, 30, 1, 0 }, 415 { "CPU", 24, 1, 1, 1, 0 }, 416 { "SYS", 25, 1, 1, 1, 0 }, 417 { "PWM", 26, 1, 1, 1, 0 }, 418 { "CPU Fan", 32, 2, 60, 1, 0 }, 419 { "NB Fan", 33, 2, 60, 1, 0 }, 420 { "SYS Fan", 34, 2, 60, 1, 0 }, 421 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 422 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 423 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 424 { NULL, 0, 0, 0, 0, 0 } } 425 }, 426 { 0x0016, { "AW9D-MAX", NULL }, { 427 { "CPU Core", 0, 0, 10, 1, 0 }, 428 { "DDR2", 1, 0, 20, 1, 0 }, 429 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 430 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 431 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 432 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 433 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 434 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 435 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 436 { "ATX +5V", 9, 0, 30, 1, 0 }, 437 { "+3.3V", 10, 0, 20, 1, 0 }, 438 { "5VSB", 11, 0, 30, 1, 0 }, 439 { "CPU", 24, 1, 1, 1, 0 }, 440 { "System", 25, 1, 1, 1, 0 }, 441 { "PWM1", 26, 1, 1, 1, 0 }, 442 { "PWM2", 27, 1, 1, 1, 0 }, 443 { "PWM3", 28, 1, 1, 1, 0 }, 444 { "PWM4", 29, 1, 1, 1, 0 }, 445 { "CPU Fan", 32, 2, 60, 1, 0 }, 446 { "NB Fan", 33, 2, 60, 1, 0 }, 447 { "SYS Fan", 34, 2, 60, 1, 0 }, 448 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 449 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 450 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 451 { "OTES1 Fan", 38, 2, 60, 1, 0 }, 452 { NULL, 0, 0, 0, 0, 0 } } 453 }, 454 { 0x0017, { NULL } /* Unknown, need DMI string */, { 455 { "CPU Core", 0, 0, 10, 1, 0 }, 456 { "DDR2", 1, 0, 20, 1, 0 }, 457 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 458 { "HyperTransport", 3, 0, 10, 1, 0 }, 459 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 460 { "NB 1.8V", 4, 0, 10, 1, 0 }, 461 { "NB 1.2V ", 13, 0, 10, 1, 0 }, 462 { "SB 1.2V", 5, 0, 10, 1, 0 }, 463 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 464 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 465 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 466 { "ATX +5V", 9, 0, 30, 1, 0 }, 467 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 468 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 469 { "CPU", 24, 1, 1, 1, 0 }, 470 { "System", 26, 1, 1, 1, 0 }, 471 { "PWM", 27, 1, 1, 1, 0 }, 472 { "CPU FAN", 32, 2, 60, 1, 0 }, 473 { "SYS FAN", 34, 2, 60, 1, 0 }, 474 { "AUX1 FAN", 35, 2, 60, 1, 0 }, 475 { "AUX2 FAN", 36, 2, 60, 1, 0 }, 476 { "AUX3 FAN", 37, 2, 60, 1, 0 }, 477 { NULL, 0, 0, 0, 0, 0 } } 478 }, 479 { 0x0018, { "AB9 QuadGT", NULL }, { 480 { "CPU Core", 0, 0, 10, 1, 0 }, 481 { "DDR2", 1, 0, 20, 1, 0 }, 482 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 483 { "CPU VTT", 3, 0, 10, 1, 0 }, 484 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 485 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 486 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 487 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 488 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 489 { "ATX +5V", 9, 0, 30, 1, 0 }, 490 { "+3.3V", 10, 0, 20, 1, 0 }, 491 { "5VSB", 11, 0, 30, 1, 0 }, 492 { "CPU", 24, 1, 1, 1, 0 }, 493 { "System", 25, 1, 1, 1, 0 }, 494 { "PWM Phase1", 26, 1, 1, 1, 0 }, 495 { "PWM Phase2", 27, 1, 1, 1, 0 }, 496 { "PWM Phase3", 28, 1, 1, 1, 0 }, 497 { "PWM Phase4", 29, 1, 1, 1, 0 }, 498 { "PWM Phase5", 30, 1, 1, 1, 0 }, 499 { "CPU Fan", 32, 2, 60, 1, 0 }, 500 { "SYS Fan", 34, 2, 60, 1, 0 }, 501 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 502 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 503 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 504 { NULL, 0, 0, 0, 0, 0 } } 505 }, 506 { 0x0019, { "IN9 32X MAX", NULL }, { 507 { "CPU Core", 7, 0, 10, 1, 0 }, 508 { "DDR2", 13, 0, 20, 1, 0 }, 509 { "DDR2 VTT", 14, 0, 10, 1, 0 }, 510 { "CPU VTT", 3, 0, 20, 1, 0 }, 511 { "NB 1.2V", 4, 0, 10, 1, 0 }, 512 { "SB 1.5V", 6, 0, 10, 1, 0 }, 513 { "HyperTransport", 5, 0, 10, 1, 0 }, 514 { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 }, 515 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 516 { "ATX +5V", 9, 0, 30, 1, 0 }, 517 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 518 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 519 { "CPU", 24, 1, 1, 1, 0 }, 520 { "System", 25, 1, 1, 1, 0 }, 521 { "PWM Phase1", 26, 1, 1, 1, 0 }, 522 { "PWM Phase2", 27, 1, 1, 1, 0 }, 523 { "PWM Phase3", 28, 1, 1, 1, 0 }, 524 { "PWM Phase4", 29, 1, 1, 1, 0 }, 525 { "PWM Phase5", 30, 1, 1, 1, 0 }, 526 { "CPU FAN", 32, 2, 60, 1, 0 }, 527 { "SYS FAN", 34, 2, 60, 1, 0 }, 528 { "AUX1 FAN", 33, 2, 60, 1, 0 }, 529 { "AUX2 FAN", 35, 2, 60, 1, 0 }, 530 { "AUX3 FAN", 36, 2, 60, 1, 0 }, 531 { NULL, 0, 0, 0, 0, 0 } } 532 }, 533 { 0x001A, { "IP35 Pro", "IP35 Pro XE", NULL }, { 534 { "CPU Core", 0, 0, 10, 1, 0 }, 535 { "DDR2", 1, 0, 20, 1, 0 }, 536 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 537 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 538 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 539 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 540 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 541 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 542 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 543 { "ATX +5V", 9, 0, 30, 1, 0 }, 544 { "+3.3V", 10, 0, 20, 1, 0 }, 545 { "5VSB", 11, 0, 30, 1, 0 }, 546 { "CPU", 24, 1, 1, 1, 0 }, 547 { "System", 25, 1, 1, 1, 0 }, 548 { "PWM", 26, 1, 1, 1, 0 }, 549 { "PWM Phase2", 27, 1, 1, 1, 0 }, 550 { "PWM Phase3", 28, 1, 1, 1, 0 }, 551 { "PWM Phase4", 29, 1, 1, 1, 0 }, 552 { "PWM Phase5", 30, 1, 1, 1, 0 }, 553 { "CPU Fan", 32, 2, 60, 1, 0 }, 554 { "SYS Fan", 34, 2, 60, 1, 0 }, 555 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 556 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 557 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 558 { "AUX4 Fan", 37, 2, 60, 1, 0 }, 559 { NULL, 0, 0, 0, 0, 0 } } 560 }, 561 { 0x001B, { NULL } /* Unknown, need DMI string */, { 562 { "CPU Core", 0, 0, 10, 1, 0 }, 563 { "DDR3", 1, 0, 20, 1, 0 }, 564 { "DDR3 VTT", 2, 0, 10, 1, 0 }, 565 { "CPU VTT", 3, 0, 10, 1, 0 }, 566 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 567 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 568 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 569 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 570 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 571 { "ATX +5V", 9, 0, 30, 1, 0 }, 572 { "+3.3V", 10, 0, 20, 1, 0 }, 573 { "5VSB", 11, 0, 30, 1, 0 }, 574 { "CPU", 24, 1, 1, 1, 0 }, 575 { "System", 25, 1, 1, 1, 0 }, 576 { "PWM Phase1", 26, 1, 1, 1, 0 }, 577 { "PWM Phase2", 27, 1, 1, 1, 0 }, 578 { "PWM Phase3", 28, 1, 1, 1, 0 }, 579 { "PWM Phase4", 29, 1, 1, 1, 0 }, 580 { "PWM Phase5", 30, 1, 1, 1, 0 }, 581 { "CPU Fan", 32, 2, 60, 1, 0 }, 582 { "SYS Fan", 34, 2, 60, 1, 0 }, 583 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 584 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 585 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 586 { NULL, 0, 0, 0, 0, 0 } } 587 }, 588 { 0x001C, { "IX38 QuadGT", NULL }, { 589 { "CPU Core", 0, 0, 10, 1, 0 }, 590 { "DDR2", 1, 0, 20, 1, 0 }, 591 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 592 { "CPU VTT", 3, 0, 10, 1, 0 }, 593 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 594 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 595 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 596 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 597 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 598 { "ATX +5V", 9, 0, 30, 1, 0 }, 599 { "+3.3V", 10, 0, 20, 1, 0 }, 600 { "5VSB", 11, 0, 30, 1, 0 }, 601 { "CPU", 24, 1, 1, 1, 0 }, 602 { "System", 25, 1, 1, 1, 0 }, 603 { "PWM Phase1", 26, 1, 1, 1, 0 }, 604 { "PWM Phase2", 27, 1, 1, 1, 0 }, 605 { "PWM Phase3", 28, 1, 1, 1, 0 }, 606 { "PWM Phase4", 29, 1, 1, 1, 0 }, 607 { "PWM Phase5", 30, 1, 1, 1, 0 }, 608 { "CPU Fan", 32, 2, 60, 1, 0 }, 609 { "SYS Fan", 34, 2, 60, 1, 0 }, 610 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 611 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 612 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 613 { NULL, 0, 0, 0, 0, 0 } } 614 }, 615 { 0x0000, { NULL }, { { NULL, 0, 0, 0, 0, 0 } } } 616 }; 617 618 619 /* Insmod parameters */ 620 static bool force; 621 module_param(force, bool, 0); 622 MODULE_PARM_DESC(force, "Set to one to force detection."); 623 /* Default verbose is 1, since this driver is still in the testing phase */ 624 static bool verbose = 1; 625 module_param(verbose, bool, 0644); 626 MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting"); 627 628 static const char *never_happen = "This should never happen."; 629 static const char *report_this = 630 "Please report this to the abituguru3 maintainer (see MAINTAINERS)"; 631 632 /* wait while the uguru is busy (usually after a write) */ 633 static int abituguru3_wait_while_busy(struct abituguru3_data *data) 634 { 635 u8 x; 636 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 637 638 while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 639 ABIT_UGURU3_STATUS_BUSY) { 640 timeout--; 641 if (timeout == 0) 642 return x; 643 /* 644 * sleep a bit before our last try, to give the uGuru3 one 645 * last chance to respond. 646 */ 647 if (timeout == 1) 648 msleep(1); 649 } 650 return ABIT_UGURU3_SUCCESS; 651 } 652 653 /* wait till uguru is ready to be read */ 654 static int abituguru3_wait_for_read(struct abituguru3_data *data) 655 { 656 u8 x; 657 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 658 659 while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 660 ABIT_UGURU3_STATUS_READY_FOR_READ)) { 661 timeout--; 662 if (timeout == 0) 663 return x; 664 /* 665 * sleep a bit before our last try, to give the uGuru3 one 666 * last chance to respond. 667 */ 668 if (timeout == 1) 669 msleep(1); 670 } 671 return ABIT_UGURU3_SUCCESS; 672 } 673 674 /* 675 * This synchronizes us with the uGuru3's protocol state machine, this 676 * must be done before each command. 677 */ 678 static int abituguru3_synchronize(struct abituguru3_data *data) 679 { 680 int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT; 681 682 x = abituguru3_wait_while_busy(data); 683 if (x != ABIT_UGURU3_SUCCESS) { 684 ABIT_UGURU3_DEBUG("synchronize timeout during initial busy " 685 "wait, status: 0x%02x\n", x); 686 return -EIO; 687 } 688 689 outb(0x20, data->addr + ABIT_UGURU3_DATA); 690 x = abituguru3_wait_while_busy(data); 691 if (x != ABIT_UGURU3_SUCCESS) { 692 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, " 693 "status: 0x%02x\n", x); 694 return -EIO; 695 } 696 697 outb(0x10, data->addr + ABIT_UGURU3_CMD); 698 x = abituguru3_wait_while_busy(data); 699 if (x != ABIT_UGURU3_SUCCESS) { 700 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, " 701 "status: 0x%02x\n", x); 702 return -EIO; 703 } 704 705 outb(0x00, data->addr + ABIT_UGURU3_CMD); 706 x = abituguru3_wait_while_busy(data); 707 if (x != ABIT_UGURU3_SUCCESS) { 708 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, " 709 "status: 0x%02x\n", x); 710 return -EIO; 711 } 712 713 x = abituguru3_wait_for_read(data); 714 if (x != ABIT_UGURU3_SUCCESS) { 715 ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, " 716 "status: 0x%02x\n", x); 717 return -EIO; 718 } 719 720 while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) { 721 timeout--; 722 if (timeout == 0) { 723 ABIT_UGURU3_DEBUG("synchronize timeout cmd does not " 724 "hold 0xAC after synchronize, cmd: 0x%02x\n", 725 x); 726 return -EIO; 727 } 728 msleep(1); 729 } 730 return 0; 731 } 732 733 /* 734 * Read count bytes from sensor sensor_addr in bank bank_addr and store the 735 * result in buf 736 */ 737 static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset, 738 u8 count, u8 *buf) 739 { 740 int i, x; 741 742 x = abituguru3_synchronize(data); 743 if (x) 744 return x; 745 746 outb(0x1A, data->addr + ABIT_UGURU3_DATA); 747 x = abituguru3_wait_while_busy(data); 748 if (x != ABIT_UGURU3_SUCCESS) { 749 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 750 "sending 0x1A, status: 0x%02x\n", (unsigned int)bank, 751 (unsigned int)offset, x); 752 return -EIO; 753 } 754 755 outb(bank, data->addr + ABIT_UGURU3_CMD); 756 x = abituguru3_wait_while_busy(data); 757 if (x != ABIT_UGURU3_SUCCESS) { 758 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 759 "sending the bank, status: 0x%02x\n", 760 (unsigned int)bank, (unsigned int)offset, x); 761 return -EIO; 762 } 763 764 outb(offset, data->addr + ABIT_UGURU3_CMD); 765 x = abituguru3_wait_while_busy(data); 766 if (x != ABIT_UGURU3_SUCCESS) { 767 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 768 "sending the offset, status: 0x%02x\n", 769 (unsigned int)bank, (unsigned int)offset, x); 770 return -EIO; 771 } 772 773 outb(count, data->addr + ABIT_UGURU3_CMD); 774 x = abituguru3_wait_while_busy(data); 775 if (x != ABIT_UGURU3_SUCCESS) { 776 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 777 "sending the count, status: 0x%02x\n", 778 (unsigned int)bank, (unsigned int)offset, x); 779 return -EIO; 780 } 781 782 for (i = 0; i < count; i++) { 783 x = abituguru3_wait_for_read(data); 784 if (x != ABIT_UGURU3_SUCCESS) { 785 ABIT_UGURU3_DEBUG("timeout reading byte %d from " 786 "0x%02x:0x%02x, status: 0x%02x\n", i, 787 (unsigned int)bank, (unsigned int)offset, x); 788 break; 789 } 790 buf[i] = inb(data->addr + ABIT_UGURU3_CMD); 791 } 792 return i; 793 } 794 795 /* 796 * Sensor settings are stored 1 byte per offset with the bytes 797 * placed add consecutive offsets. 798 */ 799 static int abituguru3_read_increment_offset(struct abituguru3_data *data, 800 u8 bank, u8 offset, u8 count, 801 u8 *buf, int offset_count) 802 { 803 int i, x; 804 805 for (i = 0; i < offset_count; i++) { 806 x = abituguru3_read(data, bank, offset + i, count, 807 buf + i * count); 808 if (x != count) { 809 if (x < 0) 810 return x; 811 return i * count + x; 812 } 813 } 814 815 return i * count; 816 } 817 818 /* 819 * Following are the sysfs callback functions. These functions expect: 820 * sensor_device_attribute_2->index: index into the data->sensors array 821 * sensor_device_attribute_2->nr: register offset, bitmask or NA. 822 */ 823 static struct abituguru3_data *abituguru3_update_device(struct device *dev); 824 825 static ssize_t show_value(struct device *dev, 826 struct device_attribute *devattr, char *buf) 827 { 828 int value; 829 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 830 struct abituguru3_data *data = abituguru3_update_device(dev); 831 const struct abituguru3_sensor_info *sensor; 832 833 if (!data) 834 return -EIO; 835 836 sensor = &data->sensors[attr->index]; 837 838 /* are we reading a setting, or is this a normal read? */ 839 if (attr->nr) 840 value = data->settings[sensor->port][attr->nr]; 841 else 842 value = data->value[sensor->port]; 843 844 /* convert the value */ 845 value = (value * sensor->multiplier) / sensor->divisor + 846 sensor->offset; 847 848 /* 849 * alternatively we could update the sensors settings struct for this, 850 * but then its contents would differ from the windows sw ini files 851 */ 852 if (sensor->type == ABIT_UGURU3_TEMP_SENSOR) 853 value *= 1000; 854 855 return sprintf(buf, "%d\n", value); 856 } 857 858 static ssize_t show_alarm(struct device *dev, 859 struct device_attribute *devattr, char *buf) 860 { 861 int port; 862 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 863 struct abituguru3_data *data = abituguru3_update_device(dev); 864 865 if (!data) 866 return -EIO; 867 868 port = data->sensors[attr->index].port; 869 870 /* 871 * See if the alarm bit for this sensor is set and if a bitmask is 872 * given in attr->nr also check if the alarm matches the type of alarm 873 * we're looking for (for volt it can be either low or high). The type 874 * is stored in a few readonly bits in the settings of the sensor. 875 */ 876 if ((data->alarms[port / 8] & (0x01 << (port % 8))) && 877 (!attr->nr || (data->settings[port][0] & attr->nr))) 878 return sprintf(buf, "1\n"); 879 else 880 return sprintf(buf, "0\n"); 881 } 882 883 static ssize_t show_mask(struct device *dev, 884 struct device_attribute *devattr, char *buf) 885 { 886 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 887 struct abituguru3_data *data = dev_get_drvdata(dev); 888 889 if (data->settings[data->sensors[attr->index].port][0] & attr->nr) 890 return sprintf(buf, "1\n"); 891 else 892 return sprintf(buf, "0\n"); 893 } 894 895 static ssize_t show_label(struct device *dev, 896 struct device_attribute *devattr, char *buf) 897 { 898 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 899 struct abituguru3_data *data = dev_get_drvdata(dev); 900 901 return sprintf(buf, "%s\n", data->sensors[attr->index].name); 902 } 903 904 static ssize_t show_name(struct device *dev, 905 struct device_attribute *devattr, char *buf) 906 { 907 return sprintf(buf, "%s\n", ABIT_UGURU3_NAME); 908 } 909 910 /* Sysfs attr templates, the real entries are generated automatically. */ 911 static const 912 struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { { 913 SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0), 914 SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0), 915 SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0), 916 SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL, 917 ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0), 918 SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL, 919 ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0), 920 SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL, 921 ABIT_UGURU3_BEEP_ENABLE, 0), 922 SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL, 923 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 924 SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL, 925 ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0), 926 SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL, 927 ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0), 928 SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0) 929 }, { 930 SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0), 931 SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0), 932 SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0), 933 SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0), 934 SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL, 935 ABIT_UGURU3_BEEP_ENABLE, 0), 936 SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL, 937 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 938 SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL, 939 ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0), 940 SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0) 941 }, { 942 SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0), 943 SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0), 944 SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0), 945 SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL, 946 ABIT_UGURU3_BEEP_ENABLE, 0), 947 SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL, 948 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 949 SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL, 950 ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0), 951 SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0) 952 } }; 953 954 static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = { 955 SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0), 956 }; 957 958 static int abituguru3_probe(struct platform_device *pdev) 959 { 960 const int no_sysfs_attr[3] = { 10, 8, 7 }; 961 int sensor_index[3] = { 0, 1, 1 }; 962 struct abituguru3_data *data; 963 int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV; 964 char *sysfs_filename; 965 u8 buf[2]; 966 u16 id; 967 968 data = devm_kzalloc(&pdev->dev, sizeof(struct abituguru3_data), 969 GFP_KERNEL); 970 if (!data) 971 return -ENOMEM; 972 973 data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start; 974 mutex_init(&data->update_lock); 975 platform_set_drvdata(pdev, data); 976 977 /* Read the motherboard ID */ 978 i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, ABIT_UGURU3_BOARD_ID, 979 2, buf); 980 if (i != 2) 981 goto abituguru3_probe_error; 982 983 /* Completely read the uGuru to see if one really is there */ 984 if (!abituguru3_update_device(&pdev->dev)) 985 goto abituguru3_probe_error; 986 987 /* lookup the ID in our motherboard table */ 988 id = ((u16)buf[0] << 8) | (u16)buf[1]; 989 for (i = 0; abituguru3_motherboards[i].id; i++) 990 if (abituguru3_motherboards[i].id == id) 991 break; 992 if (!abituguru3_motherboards[i].id) { 993 pr_err("error unknown motherboard ID: %04X. %s\n", 994 (unsigned int)id, report_this); 995 goto abituguru3_probe_error; 996 } 997 data->sensors = abituguru3_motherboards[i].sensors; 998 999 pr_info("found Abit uGuru3, motherboard ID: %04X\n", (unsigned int)id); 1000 1001 /* Fill the sysfs attr array */ 1002 sysfs_attr_i = 0; 1003 sysfs_filename = data->sysfs_names; 1004 sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH; 1005 for (i = 0; data->sensors[i].name; i++) { 1006 /* Fail safe check, this should never happen! */ 1007 if (i >= ABIT_UGURU3_MAX_NO_SENSORS) { 1008 pr_err("Fatal error motherboard has more sensors then ABIT_UGURU3_MAX_NO_SENSORS. %s %s\n", 1009 never_happen, report_this); 1010 res = -ENAMETOOLONG; 1011 goto abituguru3_probe_error; 1012 } 1013 type = data->sensors[i].type; 1014 for (j = 0; j < no_sysfs_attr[type]; j++) { 1015 used = snprintf(sysfs_filename, sysfs_names_free, 1016 abituguru3_sysfs_templ[type][j].dev_attr.attr. 1017 name, sensor_index[type]) + 1; 1018 data->sysfs_attr[sysfs_attr_i] = 1019 abituguru3_sysfs_templ[type][j]; 1020 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name = 1021 sysfs_filename; 1022 data->sysfs_attr[sysfs_attr_i].index = i; 1023 sysfs_filename += used; 1024 sysfs_names_free -= used; 1025 sysfs_attr_i++; 1026 } 1027 sensor_index[type]++; 1028 } 1029 /* Fail safe check, this should never happen! */ 1030 if (sysfs_names_free < 0) { 1031 pr_err("Fatal error ran out of space for sysfs attr names. %s %s\n", 1032 never_happen, report_this); 1033 res = -ENAMETOOLONG; 1034 goto abituguru3_probe_error; 1035 } 1036 1037 /* Register sysfs hooks */ 1038 for (i = 0; i < sysfs_attr_i; i++) 1039 if (device_create_file(&pdev->dev, 1040 &data->sysfs_attr[i].dev_attr)) 1041 goto abituguru3_probe_error; 1042 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1043 if (device_create_file(&pdev->dev, 1044 &abituguru3_sysfs_attr[i].dev_attr)) 1045 goto abituguru3_probe_error; 1046 1047 data->hwmon_dev = hwmon_device_register(&pdev->dev); 1048 if (IS_ERR(data->hwmon_dev)) { 1049 res = PTR_ERR(data->hwmon_dev); 1050 goto abituguru3_probe_error; 1051 } 1052 1053 return 0; /* success */ 1054 1055 abituguru3_probe_error: 1056 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1057 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1058 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1059 device_remove_file(&pdev->dev, 1060 &abituguru3_sysfs_attr[i].dev_attr); 1061 return res; 1062 } 1063 1064 static int abituguru3_remove(struct platform_device *pdev) 1065 { 1066 int i; 1067 struct abituguru3_data *data = platform_get_drvdata(pdev); 1068 1069 hwmon_device_unregister(data->hwmon_dev); 1070 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1071 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1072 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1073 device_remove_file(&pdev->dev, 1074 &abituguru3_sysfs_attr[i].dev_attr); 1075 return 0; 1076 } 1077 1078 static struct abituguru3_data *abituguru3_update_device(struct device *dev) 1079 { 1080 int i; 1081 struct abituguru3_data *data = dev_get_drvdata(dev); 1082 1083 mutex_lock(&data->update_lock); 1084 if (!data->valid || time_after(jiffies, data->last_updated + HZ)) { 1085 /* Clear data->valid while updating */ 1086 data->valid = false; 1087 /* Read alarms */ 1088 if (abituguru3_read_increment_offset(data, 1089 ABIT_UGURU3_SETTINGS_BANK, 1090 ABIT_UGURU3_ALARMS_START, 1091 1, data->alarms, 48/8) != (48/8)) 1092 goto LEAVE_UPDATE; 1093 /* Read in and temp sensors (3 byte settings / sensor) */ 1094 for (i = 0; i < 32; i++) { 1095 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1096 ABIT_UGURU3_VALUES_START + i, 1097 1, &data->value[i]) != 1) 1098 goto LEAVE_UPDATE; 1099 if (abituguru3_read_increment_offset(data, 1100 ABIT_UGURU3_SETTINGS_BANK, 1101 ABIT_UGURU3_SETTINGS_START + i * 3, 1102 1, 1103 data->settings[i], 3) != 3) 1104 goto LEAVE_UPDATE; 1105 } 1106 /* Read temp sensors (2 byte settings / sensor) */ 1107 for (i = 0; i < 16; i++) { 1108 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1109 ABIT_UGURU3_VALUES_START + 32 + i, 1110 1, &data->value[32 + i]) != 1) 1111 goto LEAVE_UPDATE; 1112 if (abituguru3_read_increment_offset(data, 1113 ABIT_UGURU3_SETTINGS_BANK, 1114 ABIT_UGURU3_SETTINGS_START + 32 * 3 + 1115 i * 2, 1, 1116 data->settings[32 + i], 2) != 2) 1117 goto LEAVE_UPDATE; 1118 } 1119 data->last_updated = jiffies; 1120 data->valid = true; 1121 } 1122 LEAVE_UPDATE: 1123 mutex_unlock(&data->update_lock); 1124 if (data->valid) 1125 return data; 1126 else 1127 return NULL; 1128 } 1129 1130 static int abituguru3_suspend(struct device *dev) 1131 { 1132 struct abituguru3_data *data = dev_get_drvdata(dev); 1133 /* 1134 * make sure all communications with the uguru3 are done and no new 1135 * ones are started 1136 */ 1137 mutex_lock(&data->update_lock); 1138 return 0; 1139 } 1140 1141 static int abituguru3_resume(struct device *dev) 1142 { 1143 struct abituguru3_data *data = dev_get_drvdata(dev); 1144 mutex_unlock(&data->update_lock); 1145 return 0; 1146 } 1147 1148 static DEFINE_SIMPLE_DEV_PM_OPS(abituguru3_pm, abituguru3_suspend, abituguru3_resume); 1149 1150 static struct platform_driver abituguru3_driver = { 1151 .driver = { 1152 .name = ABIT_UGURU3_NAME, 1153 .pm = pm_sleep_ptr(&abituguru3_pm), 1154 }, 1155 .probe = abituguru3_probe, 1156 .remove = abituguru3_remove, 1157 }; 1158 1159 static int __init abituguru3_dmi_detect(void) 1160 { 1161 const char *board_vendor, *board_name; 1162 int i, err = (force) ? 1 : -ENODEV; 1163 const char *const *dmi_name; 1164 size_t sublen; 1165 1166 board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); 1167 if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/")) 1168 return err; 1169 1170 board_name = dmi_get_system_info(DMI_BOARD_NAME); 1171 if (!board_name) 1172 return err; 1173 1174 /* 1175 * At the moment, we don't care about the part of the vendor 1176 * DMI string contained in brackets. Truncate the string at 1177 * the first occurrence of a bracket. Trim any trailing space 1178 * from the substring. 1179 */ 1180 sublen = strcspn(board_name, "("); 1181 while (sublen > 0 && board_name[sublen - 1] == ' ') 1182 sublen--; 1183 1184 for (i = 0; abituguru3_motherboards[i].id; i++) { 1185 dmi_name = abituguru3_motherboards[i].dmi_name; 1186 for ( ; *dmi_name; dmi_name++) { 1187 if (strlen(*dmi_name) != sublen) 1188 continue; 1189 if (!strncasecmp(board_name, *dmi_name, sublen)) 1190 return 0; 1191 } 1192 } 1193 1194 /* No match found */ 1195 return 1; 1196 } 1197 1198 /* 1199 * FIXME: Manual detection should die eventually; we need to collect stable 1200 * DMI model names first before we can rely entirely on CONFIG_DMI. 1201 */ 1202 1203 static int __init abituguru3_detect(void) 1204 { 1205 /* 1206 * See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or 1207 * 0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05 1208 * or 0x55 at CMD instead, why is unknown. 1209 */ 1210 u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA); 1211 u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD); 1212 if (((data_val == 0x00) || (data_val == 0x08)) && 1213 ((cmd_val == 0xAC) || (cmd_val == 0x05) || 1214 (cmd_val == 0x55))) 1215 return 0; 1216 1217 ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " 1218 "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); 1219 1220 if (force) { 1221 pr_info("Assuming Abit uGuru3 is present because of \"force\" parameter\n"); 1222 return 0; 1223 } 1224 1225 /* No uGuru3 found */ 1226 return -ENODEV; 1227 } 1228 1229 static struct platform_device *abituguru3_pdev; 1230 1231 static int __init abituguru3_init(void) 1232 { 1233 struct resource res = { .flags = IORESOURCE_IO }; 1234 int err; 1235 1236 /* Attempt DMI detection first */ 1237 err = abituguru3_dmi_detect(); 1238 if (err < 0) 1239 return err; 1240 1241 /* 1242 * Fall back to manual detection if there was no exact 1243 * board name match, or force was specified. 1244 */ 1245 if (err > 0) { 1246 err = abituguru3_detect(); 1247 if (err) 1248 return err; 1249 1250 pr_warn("this motherboard was not detected using DMI. " 1251 "Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n"); 1252 } 1253 1254 err = platform_driver_register(&abituguru3_driver); 1255 if (err) 1256 goto exit; 1257 1258 abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, 1259 ABIT_UGURU3_BASE); 1260 if (!abituguru3_pdev) { 1261 pr_err("Device allocation failed\n"); 1262 err = -ENOMEM; 1263 goto exit_driver_unregister; 1264 } 1265 1266 res.start = ABIT_UGURU3_BASE; 1267 res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1; 1268 res.name = ABIT_UGURU3_NAME; 1269 1270 err = platform_device_add_resources(abituguru3_pdev, &res, 1); 1271 if (err) { 1272 pr_err("Device resource addition failed (%d)\n", err); 1273 goto exit_device_put; 1274 } 1275 1276 err = platform_device_add(abituguru3_pdev); 1277 if (err) { 1278 pr_err("Device addition failed (%d)\n", err); 1279 goto exit_device_put; 1280 } 1281 1282 return 0; 1283 1284 exit_device_put: 1285 platform_device_put(abituguru3_pdev); 1286 exit_driver_unregister: 1287 platform_driver_unregister(&abituguru3_driver); 1288 exit: 1289 return err; 1290 } 1291 1292 static void __exit abituguru3_exit(void) 1293 { 1294 platform_device_unregister(abituguru3_pdev); 1295 platform_driver_unregister(&abituguru3_driver); 1296 } 1297 1298 MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>"); 1299 MODULE_DESCRIPTION("Abit uGuru3 Sensor device"); 1300 MODULE_LICENSE("GPL"); 1301 1302 module_init(abituguru3_init); 1303 module_exit(abituguru3_exit); 1304