1 /* 2 abituguru3.c 3 4 Copyright (c) 2006-2008 Hans de Goede <j.w.r.degoede@hhs.nl> 5 Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk> 6 7 This program is free software; you can redistribute it and/or modify 8 it under the terms of the GNU General Public License as published by 9 the Free Software Foundation; either version 2 of the License, or 10 (at your option) any later version. 11 12 This program is distributed in the hope that it will be useful, 13 but WITHOUT ANY WARRANTY; without even the implied warranty of 14 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 GNU General Public License for more details. 16 17 You should have received a copy of the GNU General Public License 18 along with this program; if not, write to the Free Software 19 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 20 */ 21 /* 22 This driver supports the sensor part of revision 3 of the custom Abit uGuru 23 chip found on newer Abit uGuru motherboards. Note: because of lack of specs 24 only reading the sensors and their settings is supported. 25 */ 26 #include <linux/module.h> 27 #include <linux/init.h> 28 #include <linux/slab.h> 29 #include <linux/jiffies.h> 30 #include <linux/mutex.h> 31 #include <linux/err.h> 32 #include <linux/delay.h> 33 #include <linux/platform_device.h> 34 #include <linux/hwmon.h> 35 #include <linux/hwmon-sysfs.h> 36 #include <linux/dmi.h> 37 #include <asm/io.h> 38 39 /* uGuru3 bank addresses */ 40 #define ABIT_UGURU3_SETTINGS_BANK 0x01 41 #define ABIT_UGURU3_SENSORS_BANK 0x08 42 #define ABIT_UGURU3_MISC_BANK 0x09 43 #define ABIT_UGURU3_ALARMS_START 0x1E 44 #define ABIT_UGURU3_SETTINGS_START 0x24 45 #define ABIT_UGURU3_VALUES_START 0x80 46 #define ABIT_UGURU3_BOARD_ID 0x0A 47 /* uGuru3 sensor bank flags */ /* Alarm if: */ 48 #define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */ 49 #define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */ 50 #define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */ 51 #define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */ 52 #define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */ 53 #define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */ 54 #define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */ 55 #define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */ 56 #define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */ 57 /* sensor types */ 58 #define ABIT_UGURU3_IN_SENSOR 0 59 #define ABIT_UGURU3_TEMP_SENSOR 1 60 #define ABIT_UGURU3_FAN_SENSOR 2 61 62 /* Timeouts / Retries, if these turn out to need a lot of fiddling we could 63 convert them to params. Determined by trial and error. I assume this is 64 cpu-speed independent, since the ISA-bus and not the CPU should be the 65 bottleneck. */ 66 #define ABIT_UGURU3_WAIT_TIMEOUT 250 67 /* Normally the 0xAC at the end of synchronize() is reported after the 68 first read, but sometimes not and we need to poll */ 69 #define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5 70 /* utility macros */ 71 #define ABIT_UGURU3_NAME "abituguru3" 72 #define ABIT_UGURU3_DEBUG(format, arg...) \ 73 if (verbose) \ 74 printk(KERN_DEBUG ABIT_UGURU3_NAME ": " format , ## arg) 75 76 /* Macros to help calculate the sysfs_names array length */ 77 #define ABIT_UGURU3_MAX_NO_SENSORS 26 78 /* sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0, 79 in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 */ 80 #define ABIT_UGURU3_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11) 81 /* sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0, 82 temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0, 83 temp??_label\0 */ 84 #define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13) 85 /* sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0, 86 fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 */ 87 #define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12) 88 /* Worst case scenario 16 in sensors (longest names_length) and the rest 89 temp sensors (second longest names_length). */ 90 #define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \ 91 (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH) 92 93 /* All the macros below are named identical to the openguru2 program 94 reverse engineered by Louis Kruger, hence the names might not be 100% 95 logical. I could come up with better names, but I prefer keeping the names 96 identical so that this driver can be compared with his work more easily. */ 97 /* Two i/o-ports are used by uGuru */ 98 #define ABIT_UGURU3_BASE 0x00E0 99 #define ABIT_UGURU3_CMD 0x00 100 #define ABIT_UGURU3_DATA 0x04 101 #define ABIT_UGURU3_REGION_LENGTH 5 102 /* The wait_xxx functions return this on success and the last contents 103 of the DATA register (0-255) on failure. */ 104 #define ABIT_UGURU3_SUCCESS -1 105 /* uGuru status flags */ 106 #define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01 107 #define ABIT_UGURU3_STATUS_BUSY 0x02 108 109 110 /* Structures */ 111 struct abituguru3_sensor_info { 112 const char* name; 113 int port; 114 int type; 115 int multiplier; 116 int divisor; 117 int offset; 118 }; 119 120 struct abituguru3_motherboard_info { 121 u16 id; 122 const char *dmi_name; 123 /* + 1 -> end of sensors indicated by a sensor with name == NULL */ 124 struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; 125 }; 126 127 /* For the Abit uGuru, we need to keep some data in memory. 128 The structure is dynamically allocated, at the same time when a new 129 abituguru3 device is allocated. */ 130 struct abituguru3_data { 131 struct device *hwmon_dev; /* hwmon registered device */ 132 struct mutex update_lock; /* protect access to data and uGuru */ 133 unsigned short addr; /* uguru base address */ 134 char valid; /* !=0 if following fields are valid */ 135 unsigned long last_updated; /* In jiffies */ 136 137 /* For convenience the sysfs attr and their names are generated 138 automatically. We have max 10 entries per sensor (for in sensors) */ 139 struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS 140 * 10]; 141 142 /* Buffer to store the dynamically generated sysfs names */ 143 char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH]; 144 145 /* Pointer to the sensors info for the detected motherboard */ 146 const struct abituguru3_sensor_info *sensors; 147 148 /* The abituguru3 supports upto 48 sensors, and thus has registers 149 sets for 48 sensors, for convienence reasons / simplicity of the 150 code we always read and store all registers for all 48 sensors */ 151 152 /* Alarms for all 48 sensors (1 bit per sensor) */ 153 u8 alarms[48/8]; 154 155 /* Value of all 48 sensors */ 156 u8 value[48]; 157 158 /* Settings of all 48 sensors, note in and temp sensors (the first 32 159 sensors) have 3 bytes of settings, while fans only have 2 bytes, 160 for convenience we use 3 bytes for all sensors */ 161 u8 settings[48][3]; 162 }; 163 164 165 /* Constants */ 166 static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { 167 { 0x000C, NULL /* Unknown, need DMI string */, { 168 { "CPU Core", 0, 0, 10, 1, 0 }, 169 { "DDR", 1, 0, 10, 1, 0 }, 170 { "DDR VTT", 2, 0, 10, 1, 0 }, 171 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 172 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 173 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 174 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 175 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 176 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 177 { "ATX +5V", 9, 0, 30, 1, 0 }, 178 { "+3.3V", 10, 0, 20, 1, 0 }, 179 { "5VSB", 11, 0, 30, 1, 0 }, 180 { "CPU", 24, 1, 1, 1, 0 }, 181 { "System", 25, 1, 1, 1, 0 }, 182 { "PWM", 26, 1, 1, 1, 0 }, 183 { "CPU Fan", 32, 2, 60, 1, 0 }, 184 { "NB Fan", 33, 2, 60, 1, 0 }, 185 { "SYS FAN", 34, 2, 60, 1, 0 }, 186 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 187 { NULL, 0, 0, 0, 0, 0 } } 188 }, 189 { 0x000D, NULL /* Abit AW8, need DMI string */, { 190 { "CPU Core", 0, 0, 10, 1, 0 }, 191 { "DDR", 1, 0, 10, 1, 0 }, 192 { "DDR VTT", 2, 0, 10, 1, 0 }, 193 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 194 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 195 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 196 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 197 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 198 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 199 { "ATX +5V", 9, 0, 30, 1, 0 }, 200 { "+3.3V", 10, 0, 20, 1, 0 }, 201 { "5VSB", 11, 0, 30, 1, 0 }, 202 { "CPU", 24, 1, 1, 1, 0 }, 203 { "System", 25, 1, 1, 1, 0 }, 204 { "PWM1", 26, 1, 1, 1, 0 }, 205 { "PWM2", 27, 1, 1, 1, 0 }, 206 { "PWM3", 28, 1, 1, 1, 0 }, 207 { "PWM4", 29, 1, 1, 1, 0 }, 208 { "CPU Fan", 32, 2, 60, 1, 0 }, 209 { "NB Fan", 33, 2, 60, 1, 0 }, 210 { "SYS Fan", 34, 2, 60, 1, 0 }, 211 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 212 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 213 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 214 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 215 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 216 { NULL, 0, 0, 0, 0, 0 } } 217 }, 218 { 0x000E, NULL /* AL-8, need DMI string */, { 219 { "CPU Core", 0, 0, 10, 1, 0 }, 220 { "DDR", 1, 0, 10, 1, 0 }, 221 { "DDR VTT", 2, 0, 10, 1, 0 }, 222 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 223 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 224 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 225 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 226 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 227 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 228 { "ATX +5V", 9, 0, 30, 1, 0 }, 229 { "+3.3V", 10, 0, 20, 1, 0 }, 230 { "5VSB", 11, 0, 30, 1, 0 }, 231 { "CPU", 24, 1, 1, 1, 0 }, 232 { "System", 25, 1, 1, 1, 0 }, 233 { "PWM", 26, 1, 1, 1, 0 }, 234 { "CPU Fan", 32, 2, 60, 1, 0 }, 235 { "NB Fan", 33, 2, 60, 1, 0 }, 236 { "SYS Fan", 34, 2, 60, 1, 0 }, 237 { NULL, 0, 0, 0, 0, 0 } } 238 }, 239 { 0x000F, NULL /* Unknown, need DMI string */, { 240 { "CPU Core", 0, 0, 10, 1, 0 }, 241 { "DDR", 1, 0, 10, 1, 0 }, 242 { "DDR VTT", 2, 0, 10, 1, 0 }, 243 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 244 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 245 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 246 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 247 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 248 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 249 { "ATX +5V", 9, 0, 30, 1, 0 }, 250 { "+3.3V", 10, 0, 20, 1, 0 }, 251 { "5VSB", 11, 0, 30, 1, 0 }, 252 { "CPU", 24, 1, 1, 1, 0 }, 253 { "System", 25, 1, 1, 1, 0 }, 254 { "PWM", 26, 1, 1, 1, 0 }, 255 { "CPU Fan", 32, 2, 60, 1, 0 }, 256 { "NB Fan", 33, 2, 60, 1, 0 }, 257 { "SYS Fan", 34, 2, 60, 1, 0 }, 258 { NULL, 0, 0, 0, 0, 0 } } 259 }, 260 { 0x0010, NULL /* Abit NI8 SLI GR, need DMI string */, { 261 { "CPU Core", 0, 0, 10, 1, 0 }, 262 { "DDR", 1, 0, 10, 1, 0 }, 263 { "DDR VTT", 2, 0, 10, 1, 0 }, 264 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 265 { "NB 1.4V", 4, 0, 10, 1, 0 }, 266 { "SB 1.5V", 6, 0, 10, 1, 0 }, 267 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 268 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 269 { "ATX +5V", 9, 0, 30, 1, 0 }, 270 { "+3.3V", 10, 0, 20, 1, 0 }, 271 { "5VSB", 11, 0, 30, 1, 0 }, 272 { "CPU", 24, 1, 1, 1, 0 }, 273 { "SYS", 25, 1, 1, 1, 0 }, 274 { "PWM", 26, 1, 1, 1, 0 }, 275 { "CPU Fan", 32, 2, 60, 1, 0 }, 276 { "NB Fan", 33, 2, 60, 1, 0 }, 277 { "SYS Fan", 34, 2, 60, 1, 0 }, 278 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 279 { "OTES1 Fan", 36, 2, 60, 1, 0 }, 280 { NULL, 0, 0, 0, 0, 0 } } 281 }, 282 { 0x0011, "AT8 32X(ATI RD580-ULI M1575)", { 283 { "CPU Core", 0, 0, 10, 1, 0 }, 284 { "DDR", 1, 0, 20, 1, 0 }, 285 { "DDR VTT", 2, 0, 10, 1, 0 }, 286 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 287 { "NB 1.8V", 4, 0, 10, 1, 0 }, 288 { "NB 1.8V Dual", 5, 0, 10, 1, 0 }, 289 { "HTV 1.2", 3, 0, 10, 1, 0 }, 290 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 291 { "NB 1.2V", 13, 0, 10, 1, 0 }, 292 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 293 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 294 { "ATX +5V", 9, 0, 30, 1, 0 }, 295 { "+3.3V", 10, 0, 20, 1, 0 }, 296 { "5VSB", 11, 0, 30, 1, 0 }, 297 { "CPU", 24, 1, 1, 1, 0 }, 298 { "NB", 25, 1, 1, 1, 0 }, 299 { "System", 26, 1, 1, 1, 0 }, 300 { "PWM", 27, 1, 1, 1, 0 }, 301 { "CPU Fan", 32, 2, 60, 1, 0 }, 302 { "NB Fan", 33, 2, 60, 1, 0 }, 303 { "SYS Fan", 34, 2, 60, 1, 0 }, 304 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 305 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 306 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 307 { NULL, 0, 0, 0, 0, 0 } } 308 }, 309 { 0x0012, NULL /* Abit AN8 32X, need DMI string */, { 310 { "CPU Core", 0, 0, 10, 1, 0 }, 311 { "DDR", 1, 0, 20, 1, 0 }, 312 { "DDR VTT", 2, 0, 10, 1, 0 }, 313 { "HyperTransport", 3, 0, 10, 1, 0 }, 314 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 315 { "NB", 4, 0, 10, 1, 0 }, 316 { "SB", 6, 0, 10, 1, 0 }, 317 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 318 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 319 { "ATX +5V", 9, 0, 30, 1, 0 }, 320 { "+3.3V", 10, 0, 20, 1, 0 }, 321 { "5VSB", 11, 0, 30, 1, 0 }, 322 { "CPU", 24, 1, 1, 1, 0 }, 323 { "SYS", 25, 1, 1, 1, 0 }, 324 { "PWM", 26, 1, 1, 1, 0 }, 325 { "CPU Fan", 32, 2, 60, 1, 0 }, 326 { "NB Fan", 33, 2, 60, 1, 0 }, 327 { "SYS Fan", 34, 2, 60, 1, 0 }, 328 { "AUX1 Fan", 36, 2, 60, 1, 0 }, 329 { NULL, 0, 0, 0, 0, 0 } } 330 }, 331 { 0x0013, NULL /* Abit AW8D, need DMI string */, { 332 { "CPU Core", 0, 0, 10, 1, 0 }, 333 { "DDR", 1, 0, 10, 1, 0 }, 334 { "DDR VTT", 2, 0, 10, 1, 0 }, 335 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 336 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 337 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 338 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 339 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 340 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 341 { "ATX +5V", 9, 0, 30, 1, 0 }, 342 { "+3.3V", 10, 0, 20, 1, 0 }, 343 { "5VSB", 11, 0, 30, 1, 0 }, 344 { "CPU", 24, 1, 1, 1, 0 }, 345 { "System", 25, 1, 1, 1, 0 }, 346 { "PWM1", 26, 1, 1, 1, 0 }, 347 { "PWM2", 27, 1, 1, 1, 0 }, 348 { "PWM3", 28, 1, 1, 1, 0 }, 349 { "PWM4", 29, 1, 1, 1, 0 }, 350 { "CPU Fan", 32, 2, 60, 1, 0 }, 351 { "NB Fan", 33, 2, 60, 1, 0 }, 352 { "SYS Fan", 34, 2, 60, 1, 0 }, 353 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 354 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 355 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 356 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 357 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 358 { NULL, 0, 0, 0, 0, 0 } } 359 }, 360 { 0x0014, NULL /* Abit AB9 Pro, need DMI string */, { 361 { "CPU Core", 0, 0, 10, 1, 0 }, 362 { "DDR", 1, 0, 10, 1, 0 }, 363 { "DDR VTT", 2, 0, 10, 1, 0 }, 364 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 365 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 366 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 367 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 368 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 369 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 370 { "ATX +5V", 9, 0, 30, 1, 0 }, 371 { "+3.3V", 10, 0, 20, 1, 0 }, 372 { "5VSB", 11, 0, 30, 1, 0 }, 373 { "CPU", 24, 1, 1, 1, 0 }, 374 { "System", 25, 1, 1, 1, 0 }, 375 { "PWM", 26, 1, 1, 1, 0 }, 376 { "CPU Fan", 32, 2, 60, 1, 0 }, 377 { "NB Fan", 33, 2, 60, 1, 0 }, 378 { "SYS Fan", 34, 2, 60, 1, 0 }, 379 { NULL, 0, 0, 0, 0, 0 } } 380 }, 381 { 0x0015, NULL /* Unknown, need DMI string */, { 382 { "CPU Core", 0, 0, 10, 1, 0 }, 383 { "DDR", 1, 0, 20, 1, 0 }, 384 { "DDR VTT", 2, 0, 10, 1, 0 }, 385 { "HyperTransport", 3, 0, 10, 1, 0 }, 386 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 387 { "NB", 4, 0, 10, 1, 0 }, 388 { "SB", 6, 0, 10, 1, 0 }, 389 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 390 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 391 { "ATX +5V", 9, 0, 30, 1, 0 }, 392 { "+3.3V", 10, 0, 20, 1, 0 }, 393 { "5VSB", 11, 0, 30, 1, 0 }, 394 { "CPU", 24, 1, 1, 1, 0 }, 395 { "SYS", 25, 1, 1, 1, 0 }, 396 { "PWM", 26, 1, 1, 1, 0 }, 397 { "CPU Fan", 32, 2, 60, 1, 0 }, 398 { "NB Fan", 33, 2, 60, 1, 0 }, 399 { "SYS Fan", 34, 2, 60, 1, 0 }, 400 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 401 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 402 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 403 { NULL, 0, 0, 0, 0, 0 } } 404 }, 405 { 0x0016, "AW9D-MAX (Intel i975-ICH7)", { 406 { "CPU Core", 0, 0, 10, 1, 0 }, 407 { "DDR2", 1, 0, 20, 1, 0 }, 408 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 409 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 410 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 411 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 412 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 413 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 414 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 415 { "ATX +5V", 9, 0, 30, 1, 0 }, 416 { "+3.3V", 10, 0, 20, 1, 0 }, 417 { "5VSB", 11, 0, 30, 1, 0 }, 418 { "CPU", 24, 1, 1, 1, 0 }, 419 { "System", 25, 1, 1, 1, 0 }, 420 { "PWM1", 26, 1, 1, 1, 0 }, 421 { "PWM2", 27, 1, 1, 1, 0 }, 422 { "PWM3", 28, 1, 1, 1, 0 }, 423 { "PWM4", 29, 1, 1, 1, 0 }, 424 { "CPU Fan", 32, 2, 60, 1, 0 }, 425 { "NB Fan", 33, 2, 60, 1, 0 }, 426 { "SYS Fan", 34, 2, 60, 1, 0 }, 427 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 428 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 429 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 430 { "OTES1 Fan", 38, 2, 60, 1, 0 }, 431 { NULL, 0, 0, 0, 0, 0 } } 432 }, 433 { 0x0017, NULL /* Unknown, need DMI string */, { 434 { "CPU Core", 0, 0, 10, 1, 0 }, 435 { "DDR2", 1, 0, 20, 1, 0 }, 436 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 437 { "HyperTransport", 3, 0, 10, 1, 0 }, 438 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 439 { "NB 1.8V", 4, 0, 10, 1, 0 }, 440 { "NB 1.2V ", 13, 0, 10, 1, 0 }, 441 { "SB 1.2V", 5, 0, 10, 1, 0 }, 442 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 443 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 444 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 445 { "ATX +5V", 9, 0, 30, 1, 0 }, 446 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 447 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 448 { "CPU", 24, 1, 1, 1, 0 }, 449 { "System", 26, 1, 1, 1, 0 }, 450 { "PWM", 27, 1, 1, 1, 0 }, 451 { "CPU FAN", 32, 2, 60, 1, 0 }, 452 { "SYS FAN", 34, 2, 60, 1, 0 }, 453 { "AUX1 FAN", 35, 2, 60, 1, 0 }, 454 { "AUX2 FAN", 36, 2, 60, 1, 0 }, 455 { "AUX3 FAN", 37, 2, 60, 1, 0 }, 456 { NULL, 0, 0, 0, 0, 0 } } 457 }, 458 { 0x0018, NULL /* Unknown, need DMI string */, { 459 { "CPU Core", 0, 0, 10, 1, 0 }, 460 { "DDR2", 1, 0, 20, 1, 0 }, 461 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 462 { "CPU VTT", 3, 0, 10, 1, 0 }, 463 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 464 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 465 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 466 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 467 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 468 { "ATX +5V", 9, 0, 30, 1, 0 }, 469 { "+3.3V", 10, 0, 20, 1, 0 }, 470 { "5VSB", 11, 0, 30, 1, 0 }, 471 { "CPU", 24, 1, 1, 1, 0 }, 472 { "System", 25, 1, 1, 1, 0 }, 473 { "PWM Phase1", 26, 1, 1, 1, 0 }, 474 { "PWM Phase2", 27, 1, 1, 1, 0 }, 475 { "PWM Phase3", 28, 1, 1, 1, 0 }, 476 { "PWM Phase4", 29, 1, 1, 1, 0 }, 477 { "PWM Phase5", 30, 1, 1, 1, 0 }, 478 { "CPU Fan", 32, 2, 60, 1, 0 }, 479 { "SYS Fan", 34, 2, 60, 1, 0 }, 480 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 481 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 482 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 483 { NULL, 0, 0, 0, 0, 0 } } 484 }, 485 { 0x0019, NULL /* Unknown, need DMI string */, { 486 { "CPU Core", 7, 0, 10, 1, 0 }, 487 { "DDR2", 13, 0, 20, 1, 0 }, 488 { "DDR2 VTT", 14, 0, 10, 1, 0 }, 489 { "CPU VTT", 3, 0, 20, 1, 0 }, 490 { "NB 1.2V", 4, 0, 10, 1, 0 }, 491 { "SB 1.5V", 6, 0, 10, 1, 0 }, 492 { "HyperTransport", 5, 0, 10, 1, 0 }, 493 { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 }, 494 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 495 { "ATX +5V", 9, 0, 30, 1, 0 }, 496 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 497 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 498 { "CPU", 24, 1, 1, 1, 0 }, 499 { "System", 25, 1, 1, 1, 0 }, 500 { "PWM Phase1", 26, 1, 1, 1, 0 }, 501 { "PWM Phase2", 27, 1, 1, 1, 0 }, 502 { "PWM Phase3", 28, 1, 1, 1, 0 }, 503 { "PWM Phase4", 29, 1, 1, 1, 0 }, 504 { "PWM Phase5", 30, 1, 1, 1, 0 }, 505 { "CPU FAN", 32, 2, 60, 1, 0 }, 506 { "SYS FAN", 34, 2, 60, 1, 0 }, 507 { "AUX1 FAN", 33, 2, 60, 1, 0 }, 508 { "AUX2 FAN", 35, 2, 60, 1, 0 }, 509 { "AUX3 FAN", 36, 2, 60, 1, 0 }, 510 { NULL, 0, 0, 0, 0, 0 } } 511 }, 512 { 0x001A, "IP35 Pro(Intel P35-ICH9R)", { 513 { "CPU Core", 0, 0, 10, 1, 0 }, 514 { "DDR2", 1, 0, 20, 1, 0 }, 515 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 516 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 517 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 518 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 519 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 520 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 521 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 522 { "ATX +5V", 9, 0, 30, 1, 0 }, 523 { "+3.3V", 10, 0, 20, 1, 0 }, 524 { "5VSB", 11, 0, 30, 1, 0 }, 525 { "CPU", 24, 1, 1, 1, 0 }, 526 { "System", 25, 1, 1, 1, 0 }, 527 { "PWM", 26, 1, 1, 1, 0 }, 528 { "PWM Phase2", 27, 1, 1, 1, 0 }, 529 { "PWM Phase3", 28, 1, 1, 1, 0 }, 530 { "PWM Phase4", 29, 1, 1, 1, 0 }, 531 { "PWM Phase5", 30, 1, 1, 1, 0 }, 532 { "CPU Fan", 32, 2, 60, 1, 0 }, 533 { "SYS Fan", 34, 2, 60, 1, 0 }, 534 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 535 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 536 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 537 { "AUX4 Fan", 37, 2, 60, 1, 0 }, 538 { NULL, 0, 0, 0, 0, 0 } } 539 }, 540 { 0x001B, NULL /* Unknown, need DMI string */, { 541 { "CPU Core", 0, 0, 10, 1, 0 }, 542 { "DDR3", 1, 0, 20, 1, 0 }, 543 { "DDR3 VTT", 2, 0, 10, 1, 0 }, 544 { "CPU VTT", 3, 0, 10, 1, 0 }, 545 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 546 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 547 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 548 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 549 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 550 { "ATX +5V", 9, 0, 30, 1, 0 }, 551 { "+3.3V", 10, 0, 20, 1, 0 }, 552 { "5VSB", 11, 0, 30, 1, 0 }, 553 { "CPU", 24, 1, 1, 1, 0 }, 554 { "System", 25, 1, 1, 1, 0 }, 555 { "PWM Phase1", 26, 1, 1, 1, 0 }, 556 { "PWM Phase2", 27, 1, 1, 1, 0 }, 557 { "PWM Phase3", 28, 1, 1, 1, 0 }, 558 { "PWM Phase4", 29, 1, 1, 1, 0 }, 559 { "PWM Phase5", 30, 1, 1, 1, 0 }, 560 { "CPU Fan", 32, 2, 60, 1, 0 }, 561 { "SYS Fan", 34, 2, 60, 1, 0 }, 562 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 563 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 564 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 565 { NULL, 0, 0, 0, 0, 0 } } 566 }, 567 { 0x001C, NULL /* Unknown, need DMI string */, { 568 { "CPU Core", 0, 0, 10, 1, 0 }, 569 { "DDR2", 1, 0, 20, 1, 0 }, 570 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 571 { "CPU VTT", 3, 0, 10, 1, 0 }, 572 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 573 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 574 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 575 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 576 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 577 { "ATX +5V", 9, 0, 30, 1, 0 }, 578 { "+3.3V", 10, 0, 20, 1, 0 }, 579 { "5VSB", 11, 0, 30, 1, 0 }, 580 { "CPU", 24, 1, 1, 1, 0 }, 581 { "System", 25, 1, 1, 1, 0 }, 582 { "PWM Phase1", 26, 1, 1, 1, 0 }, 583 { "PWM Phase2", 27, 1, 1, 1, 0 }, 584 { "PWM Phase3", 28, 1, 1, 1, 0 }, 585 { "PWM Phase4", 29, 1, 1, 1, 0 }, 586 { "PWM Phase5", 30, 1, 1, 1, 0 }, 587 { "CPU Fan", 32, 2, 60, 1, 0 }, 588 { "SYS Fan", 34, 2, 60, 1, 0 }, 589 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 590 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 591 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 592 { NULL, 0, 0, 0, 0, 0 } } 593 }, 594 { 0x0000, NULL, { { NULL, 0, 0, 0, 0, 0 } } } 595 }; 596 597 598 /* Insmod parameters */ 599 static int force; 600 module_param(force, bool, 0); 601 MODULE_PARM_DESC(force, "Set to one to force detection."); 602 /* Default verbose is 1, since this driver is still in the testing phase */ 603 static int verbose = 1; 604 module_param(verbose, bool, 0644); 605 MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting"); 606 607 608 /* wait while the uguru is busy (usually after a write) */ 609 static int abituguru3_wait_while_busy(struct abituguru3_data *data) 610 { 611 u8 x; 612 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 613 614 while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 615 ABIT_UGURU3_STATUS_BUSY) { 616 timeout--; 617 if (timeout == 0) 618 return x; 619 /* sleep a bit before our last try, to give the uGuru3 one 620 last chance to respond. */ 621 if (timeout == 1) 622 msleep(1); 623 } 624 return ABIT_UGURU3_SUCCESS; 625 } 626 627 /* wait till uguru is ready to be read */ 628 static int abituguru3_wait_for_read(struct abituguru3_data *data) 629 { 630 u8 x; 631 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 632 633 while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 634 ABIT_UGURU3_STATUS_READY_FOR_READ)) { 635 timeout--; 636 if (timeout == 0) 637 return x; 638 /* sleep a bit before our last try, to give the uGuru3 one 639 last chance to respond. */ 640 if (timeout == 1) 641 msleep(1); 642 } 643 return ABIT_UGURU3_SUCCESS; 644 } 645 646 /* This synchronizes us with the uGuru3's protocol state machine, this 647 must be done before each command. */ 648 static int abituguru3_synchronize(struct abituguru3_data *data) 649 { 650 int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT; 651 652 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 653 ABIT_UGURU3_DEBUG("synchronize timeout during initial busy " 654 "wait, status: 0x%02x\n", x); 655 return -EIO; 656 } 657 658 outb(0x20, data->addr + ABIT_UGURU3_DATA); 659 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 660 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, " 661 "status: 0x%02x\n", x); 662 return -EIO; 663 } 664 665 outb(0x10, data->addr + ABIT_UGURU3_CMD); 666 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 667 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, " 668 "status: 0x%02x\n", x); 669 return -EIO; 670 } 671 672 outb(0x00, data->addr + ABIT_UGURU3_CMD); 673 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 674 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, " 675 "status: 0x%02x\n", x); 676 return -EIO; 677 } 678 679 if ((x = abituguru3_wait_for_read(data)) != ABIT_UGURU3_SUCCESS) { 680 ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, " 681 "status: 0x%02x\n", x); 682 return -EIO; 683 } 684 685 while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) { 686 timeout--; 687 if (timeout == 0) { 688 ABIT_UGURU3_DEBUG("synchronize timeout cmd does not " 689 "hold 0xAC after synchronize, cmd: 0x%02x\n", 690 x); 691 return -EIO; 692 } 693 msleep(1); 694 } 695 return 0; 696 } 697 698 /* Read count bytes from sensor sensor_addr in bank bank_addr and store the 699 result in buf */ 700 static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset, 701 u8 count, u8 *buf) 702 { 703 int i, x; 704 705 if ((x = abituguru3_synchronize(data))) 706 return x; 707 708 outb(0x1A, data->addr + ABIT_UGURU3_DATA); 709 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 710 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 711 "sending 0x1A, status: 0x%02x\n", (unsigned int)bank, 712 (unsigned int)offset, x); 713 return -EIO; 714 } 715 716 outb(bank, data->addr + ABIT_UGURU3_CMD); 717 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 718 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 719 "sending the bank, status: 0x%02x\n", 720 (unsigned int)bank, (unsigned int)offset, x); 721 return -EIO; 722 } 723 724 outb(offset, data->addr + ABIT_UGURU3_CMD); 725 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 726 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 727 "sending the offset, status: 0x%02x\n", 728 (unsigned int)bank, (unsigned int)offset, x); 729 return -EIO; 730 } 731 732 outb(count, data->addr + ABIT_UGURU3_CMD); 733 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 734 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 735 "sending the count, status: 0x%02x\n", 736 (unsigned int)bank, (unsigned int)offset, x); 737 return -EIO; 738 } 739 740 for (i = 0; i < count; i++) { 741 if ((x = abituguru3_wait_for_read(data)) != 742 ABIT_UGURU3_SUCCESS) { 743 ABIT_UGURU3_DEBUG("timeout reading byte %d from " 744 "0x%02x:0x%02x, status: 0x%02x\n", i, 745 (unsigned int)bank, (unsigned int)offset, x); 746 break; 747 } 748 buf[i] = inb(data->addr + ABIT_UGURU3_CMD); 749 } 750 return i; 751 } 752 753 /* Sensor settings are stored 1 byte per offset with the bytes 754 placed add consecutive offsets. */ 755 static int abituguru3_read_increment_offset(struct abituguru3_data *data, 756 u8 bank, u8 offset, u8 count, 757 u8 *buf, int offset_count) 758 { 759 int i, x; 760 761 for (i = 0; i < offset_count; i++) 762 if ((x = abituguru3_read(data, bank, offset + i, count, 763 buf + i * count)) != count) 764 return i * count + (i && (x < 0)) ? 0 : x; 765 766 return i * count; 767 } 768 769 /* Following are the sysfs callback functions. These functions expect: 770 sensor_device_attribute_2->index: index into the data->sensors array 771 sensor_device_attribute_2->nr: register offset, bitmask or NA. */ 772 static struct abituguru3_data *abituguru3_update_device(struct device *dev); 773 774 static ssize_t show_value(struct device *dev, 775 struct device_attribute *devattr, char *buf) 776 { 777 int value; 778 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 779 struct abituguru3_data *data = abituguru3_update_device(dev); 780 const struct abituguru3_sensor_info *sensor; 781 782 if (!data) 783 return -EIO; 784 785 sensor = &data->sensors[attr->index]; 786 787 /* are we reading a setting, or is this a normal read? */ 788 if (attr->nr) 789 value = data->settings[sensor->port][attr->nr]; 790 else 791 value = data->value[sensor->port]; 792 793 /* convert the value */ 794 value = (value * sensor->multiplier) / sensor->divisor + 795 sensor->offset; 796 797 /* alternatively we could update the sensors settings struct for this, 798 but then its contents would differ from the windows sw ini files */ 799 if (sensor->type == ABIT_UGURU3_TEMP_SENSOR) 800 value *= 1000; 801 802 return sprintf(buf, "%d\n", value); 803 } 804 805 static ssize_t show_alarm(struct device *dev, 806 struct device_attribute *devattr, char *buf) 807 { 808 int port; 809 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 810 struct abituguru3_data *data = abituguru3_update_device(dev); 811 812 if (!data) 813 return -EIO; 814 815 port = data->sensors[attr->index].port; 816 817 /* See if the alarm bit for this sensor is set and if a bitmask is 818 given in attr->nr also check if the alarm matches the type of alarm 819 we're looking for (for volt it can be either low or high). The type 820 is stored in a few readonly bits in the settings of the sensor. */ 821 if ((data->alarms[port / 8] & (0x01 << (port % 8))) && 822 (!attr->nr || (data->settings[port][0] & attr->nr))) 823 return sprintf(buf, "1\n"); 824 else 825 return sprintf(buf, "0\n"); 826 } 827 828 static ssize_t show_mask(struct device *dev, 829 struct device_attribute *devattr, char *buf) 830 { 831 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 832 struct abituguru3_data *data = dev_get_drvdata(dev); 833 834 if (data->settings[data->sensors[attr->index].port][0] & attr->nr) 835 return sprintf(buf, "1\n"); 836 else 837 return sprintf(buf, "0\n"); 838 } 839 840 static ssize_t show_label(struct device *dev, 841 struct device_attribute *devattr, char *buf) 842 { 843 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 844 struct abituguru3_data *data = dev_get_drvdata(dev); 845 846 return sprintf(buf, "%s\n", data->sensors[attr->index].name); 847 } 848 849 static ssize_t show_name(struct device *dev, 850 struct device_attribute *devattr, char *buf) 851 { 852 return sprintf(buf, "%s\n", ABIT_UGURU3_NAME); 853 } 854 855 /* Sysfs attr templates, the real entries are generated automatically. */ 856 static const 857 struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { { 858 SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0), 859 SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0), 860 SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0), 861 SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL, 862 ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0), 863 SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL, 864 ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0), 865 SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL, 866 ABIT_UGURU3_BEEP_ENABLE, 0), 867 SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL, 868 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 869 SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL, 870 ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0), 871 SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL, 872 ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0), 873 SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0) 874 }, { 875 SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0), 876 SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0), 877 SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0), 878 SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0), 879 SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL, 880 ABIT_UGURU3_BEEP_ENABLE, 0), 881 SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL, 882 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 883 SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL, 884 ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0), 885 SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0) 886 }, { 887 SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0), 888 SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0), 889 SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0), 890 SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL, 891 ABIT_UGURU3_BEEP_ENABLE, 0), 892 SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL, 893 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 894 SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL, 895 ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0), 896 SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0) 897 } }; 898 899 static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = { 900 SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0), 901 }; 902 903 static int __devinit abituguru3_probe(struct platform_device *pdev) 904 { 905 const int no_sysfs_attr[3] = { 10, 8, 7 }; 906 int sensor_index[3] = { 0, 1, 1 }; 907 struct abituguru3_data *data; 908 int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV; 909 char *sysfs_filename; 910 u8 buf[2]; 911 u16 id; 912 913 if (!(data = kzalloc(sizeof(struct abituguru3_data), GFP_KERNEL))) 914 return -ENOMEM; 915 916 data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start; 917 mutex_init(&data->update_lock); 918 platform_set_drvdata(pdev, data); 919 920 /* Read the motherboard ID */ 921 if ((i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, 922 ABIT_UGURU3_BOARD_ID, 2, buf)) != 2) { 923 goto abituguru3_probe_error; 924 } 925 926 /* Completely read the uGuru to see if one really is there */ 927 if (!abituguru3_update_device(&pdev->dev)) 928 goto abituguru3_probe_error; 929 930 /* lookup the ID in our motherboard table */ 931 id = ((u16)buf[0] << 8) | (u16)buf[1]; 932 for (i = 0; abituguru3_motherboards[i].id; i++) 933 if (abituguru3_motherboards[i].id == id) 934 break; 935 if (!abituguru3_motherboards[i].id) { 936 printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard " 937 "ID: %04X. Please report this to the abituguru3 " 938 "maintainer (see MAINTAINERS)\n", (unsigned int)id); 939 goto abituguru3_probe_error; 940 } 941 data->sensors = abituguru3_motherboards[i].sensors; 942 943 printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard " 944 "ID: %04X\n", (unsigned int)id); 945 946 #ifdef CONFIG_DMI 947 if (!abituguru3_motherboards[i].dmi_name) { 948 printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was " 949 "not detected using DMI. Please send the output of " 950 "\"dmidecode\" to the abituguru3 maintainer " 951 "(see MAINTAINERS)\n"); 952 } 953 #endif 954 955 /* Fill the sysfs attr array */ 956 sysfs_attr_i = 0; 957 sysfs_filename = data->sysfs_names; 958 sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH; 959 for (i = 0; data->sensors[i].name; i++) { 960 /* Fail safe check, this should never happen! */ 961 if (i >= ABIT_UGURU3_MAX_NO_SENSORS) { 962 printk(KERN_ERR ABIT_UGURU3_NAME 963 ": Fatal error motherboard has more sensors " 964 "then ABIT_UGURU3_MAX_NO_SENSORS. This should " 965 "never happen please report to the abituguru3 " 966 "maintainer (see MAINTAINERS)\n"); 967 res = -ENAMETOOLONG; 968 goto abituguru3_probe_error; 969 } 970 type = data->sensors[i].type; 971 for (j = 0; j < no_sysfs_attr[type]; j++) { 972 used = snprintf(sysfs_filename, sysfs_names_free, 973 abituguru3_sysfs_templ[type][j].dev_attr.attr. 974 name, sensor_index[type]) + 1; 975 data->sysfs_attr[sysfs_attr_i] = 976 abituguru3_sysfs_templ[type][j]; 977 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name = 978 sysfs_filename; 979 data->sysfs_attr[sysfs_attr_i].index = i; 980 sysfs_filename += used; 981 sysfs_names_free -= used; 982 sysfs_attr_i++; 983 } 984 sensor_index[type]++; 985 } 986 /* Fail safe check, this should never happen! */ 987 if (sysfs_names_free < 0) { 988 printk(KERN_ERR ABIT_UGURU3_NAME 989 ": Fatal error ran out of space for sysfs attr names. " 990 "This should never happen please report to the " 991 "abituguru3 maintainer (see MAINTAINERS)\n"); 992 res = -ENAMETOOLONG; 993 goto abituguru3_probe_error; 994 } 995 996 /* Register sysfs hooks */ 997 for (i = 0; i < sysfs_attr_i; i++) 998 if (device_create_file(&pdev->dev, 999 &data->sysfs_attr[i].dev_attr)) 1000 goto abituguru3_probe_error; 1001 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1002 if (device_create_file(&pdev->dev, 1003 &abituguru3_sysfs_attr[i].dev_attr)) 1004 goto abituguru3_probe_error; 1005 1006 data->hwmon_dev = hwmon_device_register(&pdev->dev); 1007 if (IS_ERR(data->hwmon_dev)) { 1008 res = PTR_ERR(data->hwmon_dev); 1009 goto abituguru3_probe_error; 1010 } 1011 1012 return 0; /* success */ 1013 1014 abituguru3_probe_error: 1015 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1016 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1017 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1018 device_remove_file(&pdev->dev, 1019 &abituguru3_sysfs_attr[i].dev_attr); 1020 kfree(data); 1021 return res; 1022 } 1023 1024 static int __devexit abituguru3_remove(struct platform_device *pdev) 1025 { 1026 int i; 1027 struct abituguru3_data *data = platform_get_drvdata(pdev); 1028 1029 platform_set_drvdata(pdev, NULL); 1030 hwmon_device_unregister(data->hwmon_dev); 1031 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1032 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1033 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1034 device_remove_file(&pdev->dev, 1035 &abituguru3_sysfs_attr[i].dev_attr); 1036 kfree(data); 1037 1038 return 0; 1039 } 1040 1041 static struct abituguru3_data *abituguru3_update_device(struct device *dev) 1042 { 1043 int i; 1044 struct abituguru3_data *data = dev_get_drvdata(dev); 1045 1046 mutex_lock(&data->update_lock); 1047 if (!data->valid || time_after(jiffies, data->last_updated + HZ)) { 1048 /* Clear data->valid while updating */ 1049 data->valid = 0; 1050 /* Read alarms */ 1051 if (abituguru3_read_increment_offset(data, 1052 ABIT_UGURU3_SETTINGS_BANK, 1053 ABIT_UGURU3_ALARMS_START, 1054 1, data->alarms, 48/8) != (48/8)) 1055 goto LEAVE_UPDATE; 1056 /* Read in and temp sensors (3 byte settings / sensor) */ 1057 for (i = 0; i < 32; i++) { 1058 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1059 ABIT_UGURU3_VALUES_START + i, 1060 1, &data->value[i]) != 1) 1061 goto LEAVE_UPDATE; 1062 if (abituguru3_read_increment_offset(data, 1063 ABIT_UGURU3_SETTINGS_BANK, 1064 ABIT_UGURU3_SETTINGS_START + i * 3, 1065 1, 1066 data->settings[i], 3) != 3) 1067 goto LEAVE_UPDATE; 1068 } 1069 /* Read temp sensors (2 byte settings / sensor) */ 1070 for (i = 0; i < 16; i++) { 1071 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1072 ABIT_UGURU3_VALUES_START + 32 + i, 1073 1, &data->value[32 + i]) != 1) 1074 goto LEAVE_UPDATE; 1075 if (abituguru3_read_increment_offset(data, 1076 ABIT_UGURU3_SETTINGS_BANK, 1077 ABIT_UGURU3_SETTINGS_START + 32 * 3 + 1078 i * 2, 1, 1079 data->settings[32 + i], 2) != 2) 1080 goto LEAVE_UPDATE; 1081 } 1082 data->last_updated = jiffies; 1083 data->valid = 1; 1084 } 1085 LEAVE_UPDATE: 1086 mutex_unlock(&data->update_lock); 1087 if (data->valid) 1088 return data; 1089 else 1090 return NULL; 1091 } 1092 1093 #ifdef CONFIG_PM 1094 static int abituguru3_suspend(struct platform_device *pdev, pm_message_t state) 1095 { 1096 struct abituguru3_data *data = platform_get_drvdata(pdev); 1097 /* make sure all communications with the uguru3 are done and no new 1098 ones are started */ 1099 mutex_lock(&data->update_lock); 1100 return 0; 1101 } 1102 1103 static int abituguru3_resume(struct platform_device *pdev) 1104 { 1105 struct abituguru3_data *data = platform_get_drvdata(pdev); 1106 mutex_unlock(&data->update_lock); 1107 return 0; 1108 } 1109 #else 1110 #define abituguru3_suspend NULL 1111 #define abituguru3_resume NULL 1112 #endif /* CONFIG_PM */ 1113 1114 static struct platform_driver abituguru3_driver = { 1115 .driver = { 1116 .owner = THIS_MODULE, 1117 .name = ABIT_UGURU3_NAME, 1118 }, 1119 .probe = abituguru3_probe, 1120 .remove = __devexit_p(abituguru3_remove), 1121 .suspend = abituguru3_suspend, 1122 .resume = abituguru3_resume 1123 }; 1124 1125 #ifdef CONFIG_DMI 1126 1127 static int __init abituguru3_dmi_detect(void) 1128 { 1129 const char *board_vendor, *board_name; 1130 int i, err = (force) ? 1 : -ENODEV; 1131 1132 board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); 1133 if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/")) 1134 return err; 1135 1136 board_name = dmi_get_system_info(DMI_BOARD_NAME); 1137 if (!board_name) 1138 return err; 1139 1140 for (i = 0; abituguru3_motherboards[i].id; i++) { 1141 const char *dmi_name = abituguru3_motherboards[i].dmi_name; 1142 if (dmi_name && !strcmp(dmi_name, board_name)) 1143 break; 1144 } 1145 1146 if (!abituguru3_motherboards[i].id) 1147 return 1; 1148 1149 return 0; 1150 } 1151 1152 #else /* !CONFIG_DMI */ 1153 1154 static inline int abituguru3_dmi_detect(void) 1155 { 1156 return -ENODEV; 1157 } 1158 1159 #endif /* CONFIG_DMI */ 1160 1161 /* FIXME: Manual detection should die eventually; we need to collect stable 1162 * DMI model names first before we can rely entirely on CONFIG_DMI. 1163 */ 1164 1165 static int __init abituguru3_detect(void) 1166 { 1167 /* See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or 1168 0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05 1169 or 0x55 at CMD instead, why is unknown. */ 1170 u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA); 1171 u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD); 1172 if (((data_val == 0x00) || (data_val == 0x08)) && 1173 ((cmd_val == 0xAC) || (cmd_val == 0x05) || 1174 (cmd_val == 0x55))) 1175 return 0; 1176 1177 ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " 1178 "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); 1179 1180 if (force) { 1181 printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is " 1182 "present because of \"force\" parameter\n"); 1183 return 0; 1184 } 1185 1186 /* No uGuru3 found */ 1187 return -ENODEV; 1188 } 1189 1190 static struct platform_device *abituguru3_pdev; 1191 1192 static int __init abituguru3_init(void) 1193 { 1194 struct resource res = { .flags = IORESOURCE_IO }; 1195 int err; 1196 1197 /* Attempt DMI detection first */ 1198 err = abituguru3_dmi_detect(); 1199 if (err < 0) 1200 return err; 1201 1202 /* Fall back to manual detection if there was no exact 1203 * board name match, or force was specified. 1204 */ 1205 if (err > 0) { 1206 err = abituguru3_detect(); 1207 if (err) 1208 return err; 1209 } 1210 1211 err = platform_driver_register(&abituguru3_driver); 1212 if (err) 1213 goto exit; 1214 1215 abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, 1216 ABIT_UGURU3_BASE); 1217 if (!abituguru3_pdev) { 1218 printk(KERN_ERR ABIT_UGURU3_NAME 1219 ": Device allocation failed\n"); 1220 err = -ENOMEM; 1221 goto exit_driver_unregister; 1222 } 1223 1224 res.start = ABIT_UGURU3_BASE; 1225 res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1; 1226 res.name = ABIT_UGURU3_NAME; 1227 1228 err = platform_device_add_resources(abituguru3_pdev, &res, 1); 1229 if (err) { 1230 printk(KERN_ERR ABIT_UGURU3_NAME 1231 ": Device resource addition failed (%d)\n", err); 1232 goto exit_device_put; 1233 } 1234 1235 err = platform_device_add(abituguru3_pdev); 1236 if (err) { 1237 printk(KERN_ERR ABIT_UGURU3_NAME 1238 ": Device addition failed (%d)\n", err); 1239 goto exit_device_put; 1240 } 1241 1242 return 0; 1243 1244 exit_device_put: 1245 platform_device_put(abituguru3_pdev); 1246 exit_driver_unregister: 1247 platform_driver_unregister(&abituguru3_driver); 1248 exit: 1249 return err; 1250 } 1251 1252 static void __exit abituguru3_exit(void) 1253 { 1254 platform_device_unregister(abituguru3_pdev); 1255 platform_driver_unregister(&abituguru3_driver); 1256 } 1257 1258 MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>"); 1259 MODULE_DESCRIPTION("Abit uGuru3 Sensor device"); 1260 MODULE_LICENSE("GPL"); 1261 1262 module_init(abituguru3_init); 1263 module_exit(abituguru3_exit); 1264