1 /* 2 abituguru3.c 3 4 Copyright (c) 2006-2008 Hans de Goede <j.w.r.degoede@hhs.nl> 5 Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk> 6 7 This program is free software; you can redistribute it and/or modify 8 it under the terms of the GNU General Public License as published by 9 the Free Software Foundation; either version 2 of the License, or 10 (at your option) any later version. 11 12 This program is distributed in the hope that it will be useful, 13 but WITHOUT ANY WARRANTY; without even the implied warranty of 14 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 GNU General Public License for more details. 16 17 You should have received a copy of the GNU General Public License 18 along with this program; if not, write to the Free Software 19 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 20 */ 21 /* 22 This driver supports the sensor part of revision 3 of the custom Abit uGuru 23 chip found on newer Abit uGuru motherboards. Note: because of lack of specs 24 only reading the sensors and their settings is supported. 25 */ 26 #include <linux/module.h> 27 #include <linux/init.h> 28 #include <linux/slab.h> 29 #include <linux/jiffies.h> 30 #include <linux/mutex.h> 31 #include <linux/err.h> 32 #include <linux/delay.h> 33 #include <linux/platform_device.h> 34 #include <linux/hwmon.h> 35 #include <linux/hwmon-sysfs.h> 36 #include <linux/dmi.h> 37 #include <asm/io.h> 38 39 /* uGuru3 bank addresses */ 40 #define ABIT_UGURU3_SETTINGS_BANK 0x01 41 #define ABIT_UGURU3_SENSORS_BANK 0x08 42 #define ABIT_UGURU3_MISC_BANK 0x09 43 #define ABIT_UGURU3_ALARMS_START 0x1E 44 #define ABIT_UGURU3_SETTINGS_START 0x24 45 #define ABIT_UGURU3_VALUES_START 0x80 46 #define ABIT_UGURU3_BOARD_ID 0x0A 47 /* uGuru3 sensor bank flags */ /* Alarm if: */ 48 #define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */ 49 #define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */ 50 #define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */ 51 #define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */ 52 #define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */ 53 #define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */ 54 #define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */ 55 #define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */ 56 #define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */ 57 /* sensor types */ 58 #define ABIT_UGURU3_IN_SENSOR 0 59 #define ABIT_UGURU3_TEMP_SENSOR 1 60 #define ABIT_UGURU3_FAN_SENSOR 2 61 62 /* Timeouts / Retries, if these turn out to need a lot of fiddling we could 63 convert them to params. Determined by trial and error. I assume this is 64 cpu-speed independent, since the ISA-bus and not the CPU should be the 65 bottleneck. */ 66 #define ABIT_UGURU3_WAIT_TIMEOUT 250 67 /* Normally the 0xAC at the end of synchronize() is reported after the 68 first read, but sometimes not and we need to poll */ 69 #define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5 70 /* utility macros */ 71 #define ABIT_UGURU3_NAME "abituguru3" 72 #define ABIT_UGURU3_DEBUG(format, arg...) \ 73 if (verbose) \ 74 printk(KERN_DEBUG ABIT_UGURU3_NAME ": " format , ## arg) 75 76 /* Macros to help calculate the sysfs_names array length */ 77 #define ABIT_UGURU3_MAX_NO_SENSORS 26 78 /* sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0, 79 in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 */ 80 #define ABIT_UGURU3_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11) 81 /* sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0, 82 temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0, 83 temp??_label\0 */ 84 #define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13) 85 /* sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0, 86 fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 */ 87 #define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12) 88 /* Worst case scenario 16 in sensors (longest names_length) and the rest 89 temp sensors (second longest names_length). */ 90 #define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \ 91 (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH) 92 93 /* All the macros below are named identical to the openguru2 program 94 reverse engineered by Louis Kruger, hence the names might not be 100% 95 logical. I could come up with better names, but I prefer keeping the names 96 identical so that this driver can be compared with his work more easily. */ 97 /* Two i/o-ports are used by uGuru */ 98 #define ABIT_UGURU3_BASE 0x00E0 99 #define ABIT_UGURU3_CMD 0x00 100 #define ABIT_UGURU3_DATA 0x04 101 #define ABIT_UGURU3_REGION_LENGTH 5 102 /* The wait_xxx functions return this on success and the last contents 103 of the DATA register (0-255) on failure. */ 104 #define ABIT_UGURU3_SUCCESS -1 105 /* uGuru status flags */ 106 #define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01 107 #define ABIT_UGURU3_STATUS_BUSY 0x02 108 109 110 /* Structures */ 111 struct abituguru3_sensor_info { 112 const char* name; 113 int port; 114 int type; 115 int multiplier; 116 int divisor; 117 int offset; 118 }; 119 120 struct abituguru3_motherboard_info { 121 u16 id; 122 const char *dmi_name; 123 /* + 1 -> end of sensors indicated by a sensor with name == NULL */ 124 struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; 125 }; 126 127 /* For the Abit uGuru, we need to keep some data in memory. 128 The structure is dynamically allocated, at the same time when a new 129 abituguru3 device is allocated. */ 130 struct abituguru3_data { 131 struct device *hwmon_dev; /* hwmon registered device */ 132 struct mutex update_lock; /* protect access to data and uGuru */ 133 unsigned short addr; /* uguru base address */ 134 char valid; /* !=0 if following fields are valid */ 135 unsigned long last_updated; /* In jiffies */ 136 137 /* For convenience the sysfs attr and their names are generated 138 automatically. We have max 10 entries per sensor (for in sensors) */ 139 struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS 140 * 10]; 141 142 /* Buffer to store the dynamically generated sysfs names */ 143 char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH]; 144 145 /* Pointer to the sensors info for the detected motherboard */ 146 const struct abituguru3_sensor_info *sensors; 147 148 /* The abituguru3 supports upto 48 sensors, and thus has registers 149 sets for 48 sensors, for convienence reasons / simplicity of the 150 code we always read and store all registers for all 48 sensors */ 151 152 /* Alarms for all 48 sensors (1 bit per sensor) */ 153 u8 alarms[48/8]; 154 155 /* Value of all 48 sensors */ 156 u8 value[48]; 157 158 /* Settings of all 48 sensors, note in and temp sensors (the first 32 159 sensors) have 3 bytes of settings, while fans only have 2 bytes, 160 for convenience we use 3 bytes for all sensors */ 161 u8 settings[48][3]; 162 }; 163 164 165 /* Constants */ 166 static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { 167 { 0x000C, NULL /* Unknown, need DMI string */, { 168 { "CPU Core", 0, 0, 10, 1, 0 }, 169 { "DDR", 1, 0, 10, 1, 0 }, 170 { "DDR VTT", 2, 0, 10, 1, 0 }, 171 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 172 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 173 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 174 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 175 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 176 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 177 { "ATX +5V", 9, 0, 30, 1, 0 }, 178 { "+3.3V", 10, 0, 20, 1, 0 }, 179 { "5VSB", 11, 0, 30, 1, 0 }, 180 { "CPU", 24, 1, 1, 1, 0 }, 181 { "System", 25, 1, 1, 1, 0 }, 182 { "PWM", 26, 1, 1, 1, 0 }, 183 { "CPU Fan", 32, 2, 60, 1, 0 }, 184 { "NB Fan", 33, 2, 60, 1, 0 }, 185 { "SYS FAN", 34, 2, 60, 1, 0 }, 186 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 187 { NULL, 0, 0, 0, 0, 0 } } 188 }, 189 { 0x000D, NULL /* Abit AW8, need DMI string */, { 190 { "CPU Core", 0, 0, 10, 1, 0 }, 191 { "DDR", 1, 0, 10, 1, 0 }, 192 { "DDR VTT", 2, 0, 10, 1, 0 }, 193 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 194 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 195 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 196 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 197 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 198 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 199 { "ATX +5V", 9, 0, 30, 1, 0 }, 200 { "+3.3V", 10, 0, 20, 1, 0 }, 201 { "5VSB", 11, 0, 30, 1, 0 }, 202 { "CPU", 24, 1, 1, 1, 0 }, 203 { "System", 25, 1, 1, 1, 0 }, 204 { "PWM1", 26, 1, 1, 1, 0 }, 205 { "PWM2", 27, 1, 1, 1, 0 }, 206 { "PWM3", 28, 1, 1, 1, 0 }, 207 { "PWM4", 29, 1, 1, 1, 0 }, 208 { "CPU Fan", 32, 2, 60, 1, 0 }, 209 { "NB Fan", 33, 2, 60, 1, 0 }, 210 { "SYS Fan", 34, 2, 60, 1, 0 }, 211 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 212 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 213 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 214 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 215 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 216 { NULL, 0, 0, 0, 0, 0 } } 217 }, 218 { 0x000E, NULL /* AL-8, need DMI string */, { 219 { "CPU Core", 0, 0, 10, 1, 0 }, 220 { "DDR", 1, 0, 10, 1, 0 }, 221 { "DDR VTT", 2, 0, 10, 1, 0 }, 222 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 223 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 224 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 225 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 226 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 227 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 228 { "ATX +5V", 9, 0, 30, 1, 0 }, 229 { "+3.3V", 10, 0, 20, 1, 0 }, 230 { "5VSB", 11, 0, 30, 1, 0 }, 231 { "CPU", 24, 1, 1, 1, 0 }, 232 { "System", 25, 1, 1, 1, 0 }, 233 { "PWM", 26, 1, 1, 1, 0 }, 234 { "CPU Fan", 32, 2, 60, 1, 0 }, 235 { "NB Fan", 33, 2, 60, 1, 0 }, 236 { "SYS Fan", 34, 2, 60, 1, 0 }, 237 { NULL, 0, 0, 0, 0, 0 } } 238 }, 239 { 0x000F, NULL /* Unknown, need DMI string */, { 240 { "CPU Core", 0, 0, 10, 1, 0 }, 241 { "DDR", 1, 0, 10, 1, 0 }, 242 { "DDR VTT", 2, 0, 10, 1, 0 }, 243 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 244 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 245 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 246 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 247 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 248 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 249 { "ATX +5V", 9, 0, 30, 1, 0 }, 250 { "+3.3V", 10, 0, 20, 1, 0 }, 251 { "5VSB", 11, 0, 30, 1, 0 }, 252 { "CPU", 24, 1, 1, 1, 0 }, 253 { "System", 25, 1, 1, 1, 0 }, 254 { "PWM", 26, 1, 1, 1, 0 }, 255 { "CPU Fan", 32, 2, 60, 1, 0 }, 256 { "NB Fan", 33, 2, 60, 1, 0 }, 257 { "SYS Fan", 34, 2, 60, 1, 0 }, 258 { NULL, 0, 0, 0, 0, 0 } } 259 }, 260 { 0x0010, NULL /* Abit NI8 SLI GR, need DMI string */, { 261 { "CPU Core", 0, 0, 10, 1, 0 }, 262 { "DDR", 1, 0, 10, 1, 0 }, 263 { "DDR VTT", 2, 0, 10, 1, 0 }, 264 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 265 { "NB 1.4V", 4, 0, 10, 1, 0 }, 266 { "SB 1.5V", 6, 0, 10, 1, 0 }, 267 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 268 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 269 { "ATX +5V", 9, 0, 30, 1, 0 }, 270 { "+3.3V", 10, 0, 20, 1, 0 }, 271 { "5VSB", 11, 0, 30, 1, 0 }, 272 { "CPU", 24, 1, 1, 1, 0 }, 273 { "SYS", 25, 1, 1, 1, 0 }, 274 { "PWM", 26, 1, 1, 1, 0 }, 275 { "CPU Fan", 32, 2, 60, 1, 0 }, 276 { "NB Fan", 33, 2, 60, 1, 0 }, 277 { "SYS Fan", 34, 2, 60, 1, 0 }, 278 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 279 { "OTES1 Fan", 36, 2, 60, 1, 0 }, 280 { NULL, 0, 0, 0, 0, 0 } } 281 }, 282 { 0x0011, "AT8 32X", { 283 { "CPU Core", 0, 0, 10, 1, 0 }, 284 { "DDR", 1, 0, 20, 1, 0 }, 285 { "DDR VTT", 2, 0, 10, 1, 0 }, 286 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 287 { "NB 1.8V", 4, 0, 10, 1, 0 }, 288 { "NB 1.8V Dual", 5, 0, 10, 1, 0 }, 289 { "HTV 1.2", 3, 0, 10, 1, 0 }, 290 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 291 { "NB 1.2V", 13, 0, 10, 1, 0 }, 292 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 293 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 294 { "ATX +5V", 9, 0, 30, 1, 0 }, 295 { "+3.3V", 10, 0, 20, 1, 0 }, 296 { "5VSB", 11, 0, 30, 1, 0 }, 297 { "CPU", 24, 1, 1, 1, 0 }, 298 { "NB", 25, 1, 1, 1, 0 }, 299 { "System", 26, 1, 1, 1, 0 }, 300 { "PWM", 27, 1, 1, 1, 0 }, 301 { "CPU Fan", 32, 2, 60, 1, 0 }, 302 { "NB Fan", 33, 2, 60, 1, 0 }, 303 { "SYS Fan", 34, 2, 60, 1, 0 }, 304 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 305 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 306 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 307 { NULL, 0, 0, 0, 0, 0 } } 308 }, 309 { 0x0012, NULL /* Abit AN8 32X, need DMI string */, { 310 { "CPU Core", 0, 0, 10, 1, 0 }, 311 { "DDR", 1, 0, 20, 1, 0 }, 312 { "DDR VTT", 2, 0, 10, 1, 0 }, 313 { "HyperTransport", 3, 0, 10, 1, 0 }, 314 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 315 { "NB", 4, 0, 10, 1, 0 }, 316 { "SB", 6, 0, 10, 1, 0 }, 317 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 318 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 319 { "ATX +5V", 9, 0, 30, 1, 0 }, 320 { "+3.3V", 10, 0, 20, 1, 0 }, 321 { "5VSB", 11, 0, 30, 1, 0 }, 322 { "CPU", 24, 1, 1, 1, 0 }, 323 { "SYS", 25, 1, 1, 1, 0 }, 324 { "PWM", 26, 1, 1, 1, 0 }, 325 { "CPU Fan", 32, 2, 60, 1, 0 }, 326 { "NB Fan", 33, 2, 60, 1, 0 }, 327 { "SYS Fan", 34, 2, 60, 1, 0 }, 328 { "AUX1 Fan", 36, 2, 60, 1, 0 }, 329 { NULL, 0, 0, 0, 0, 0 } } 330 }, 331 { 0x0013, NULL /* Abit AW8D, need DMI string */, { 332 { "CPU Core", 0, 0, 10, 1, 0 }, 333 { "DDR", 1, 0, 10, 1, 0 }, 334 { "DDR VTT", 2, 0, 10, 1, 0 }, 335 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 336 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 337 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 338 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 339 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 340 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 341 { "ATX +5V", 9, 0, 30, 1, 0 }, 342 { "+3.3V", 10, 0, 20, 1, 0 }, 343 { "5VSB", 11, 0, 30, 1, 0 }, 344 { "CPU", 24, 1, 1, 1, 0 }, 345 { "System", 25, 1, 1, 1, 0 }, 346 { "PWM1", 26, 1, 1, 1, 0 }, 347 { "PWM2", 27, 1, 1, 1, 0 }, 348 { "PWM3", 28, 1, 1, 1, 0 }, 349 { "PWM4", 29, 1, 1, 1, 0 }, 350 { "CPU Fan", 32, 2, 60, 1, 0 }, 351 { "NB Fan", 33, 2, 60, 1, 0 }, 352 { "SYS Fan", 34, 2, 60, 1, 0 }, 353 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 354 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 355 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 356 { "AUX4 Fan", 38, 2, 60, 1, 0 }, 357 { "AUX5 Fan", 39, 2, 60, 1, 0 }, 358 { NULL, 0, 0, 0, 0, 0 } } 359 }, 360 { 0x0014, NULL /* Abit AB9 Pro, need DMI string */, { 361 { "CPU Core", 0, 0, 10, 1, 0 }, 362 { "DDR", 1, 0, 10, 1, 0 }, 363 { "DDR VTT", 2, 0, 10, 1, 0 }, 364 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 365 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 366 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 367 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 368 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 369 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 370 { "ATX +5V", 9, 0, 30, 1, 0 }, 371 { "+3.3V", 10, 0, 20, 1, 0 }, 372 { "5VSB", 11, 0, 30, 1, 0 }, 373 { "CPU", 24, 1, 1, 1, 0 }, 374 { "System", 25, 1, 1, 1, 0 }, 375 { "PWM", 26, 1, 1, 1, 0 }, 376 { "CPU Fan", 32, 2, 60, 1, 0 }, 377 { "NB Fan", 33, 2, 60, 1, 0 }, 378 { "SYS Fan", 34, 2, 60, 1, 0 }, 379 { NULL, 0, 0, 0, 0, 0 } } 380 }, 381 { 0x0015, NULL /* Unknown, need DMI string */, { 382 { "CPU Core", 0, 0, 10, 1, 0 }, 383 { "DDR", 1, 0, 20, 1, 0 }, 384 { "DDR VTT", 2, 0, 10, 1, 0 }, 385 { "HyperTransport", 3, 0, 10, 1, 0 }, 386 { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, 387 { "NB", 4, 0, 10, 1, 0 }, 388 { "SB", 6, 0, 10, 1, 0 }, 389 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 390 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 391 { "ATX +5V", 9, 0, 30, 1, 0 }, 392 { "+3.3V", 10, 0, 20, 1, 0 }, 393 { "5VSB", 11, 0, 30, 1, 0 }, 394 { "CPU", 24, 1, 1, 1, 0 }, 395 { "SYS", 25, 1, 1, 1, 0 }, 396 { "PWM", 26, 1, 1, 1, 0 }, 397 { "CPU Fan", 32, 2, 60, 1, 0 }, 398 { "NB Fan", 33, 2, 60, 1, 0 }, 399 { "SYS Fan", 34, 2, 60, 1, 0 }, 400 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 401 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 402 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 403 { NULL, 0, 0, 0, 0, 0 } } 404 }, 405 { 0x0016, "AW9D-MAX", { 406 { "CPU Core", 0, 0, 10, 1, 0 }, 407 { "DDR2", 1, 0, 20, 1, 0 }, 408 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 409 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 410 { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, 411 { "MCH 2.5V", 5, 0, 20, 1, 0 }, 412 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 413 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 414 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 415 { "ATX +5V", 9, 0, 30, 1, 0 }, 416 { "+3.3V", 10, 0, 20, 1, 0 }, 417 { "5VSB", 11, 0, 30, 1, 0 }, 418 { "CPU", 24, 1, 1, 1, 0 }, 419 { "System", 25, 1, 1, 1, 0 }, 420 { "PWM1", 26, 1, 1, 1, 0 }, 421 { "PWM2", 27, 1, 1, 1, 0 }, 422 { "PWM3", 28, 1, 1, 1, 0 }, 423 { "PWM4", 29, 1, 1, 1, 0 }, 424 { "CPU Fan", 32, 2, 60, 1, 0 }, 425 { "NB Fan", 33, 2, 60, 1, 0 }, 426 { "SYS Fan", 34, 2, 60, 1, 0 }, 427 { "AUX1 Fan", 35, 2, 60, 1, 0 }, 428 { "AUX2 Fan", 36, 2, 60, 1, 0 }, 429 { "AUX3 Fan", 37, 2, 60, 1, 0 }, 430 { "OTES1 Fan", 38, 2, 60, 1, 0 }, 431 { NULL, 0, 0, 0, 0, 0 } } 432 }, 433 { 0x0017, NULL /* Unknown, need DMI string */, { 434 { "CPU Core", 0, 0, 10, 1, 0 }, 435 { "DDR2", 1, 0, 20, 1, 0 }, 436 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 437 { "HyperTransport", 3, 0, 10, 1, 0 }, 438 { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, 439 { "NB 1.8V", 4, 0, 10, 1, 0 }, 440 { "NB 1.2V ", 13, 0, 10, 1, 0 }, 441 { "SB 1.2V", 5, 0, 10, 1, 0 }, 442 { "PCIE 1.2V", 12, 0, 10, 1, 0 }, 443 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 444 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 445 { "ATX +5V", 9, 0, 30, 1, 0 }, 446 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 447 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 448 { "CPU", 24, 1, 1, 1, 0 }, 449 { "System", 26, 1, 1, 1, 0 }, 450 { "PWM", 27, 1, 1, 1, 0 }, 451 { "CPU FAN", 32, 2, 60, 1, 0 }, 452 { "SYS FAN", 34, 2, 60, 1, 0 }, 453 { "AUX1 FAN", 35, 2, 60, 1, 0 }, 454 { "AUX2 FAN", 36, 2, 60, 1, 0 }, 455 { "AUX3 FAN", 37, 2, 60, 1, 0 }, 456 { NULL, 0, 0, 0, 0, 0 } } 457 }, 458 { 0x0018, NULL /* Unknown, need DMI string */, { 459 { "CPU Core", 0, 0, 10, 1, 0 }, 460 { "DDR2", 1, 0, 20, 1, 0 }, 461 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 462 { "CPU VTT", 3, 0, 10, 1, 0 }, 463 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 464 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 465 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 466 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 467 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 468 { "ATX +5V", 9, 0, 30, 1, 0 }, 469 { "+3.3V", 10, 0, 20, 1, 0 }, 470 { "5VSB", 11, 0, 30, 1, 0 }, 471 { "CPU", 24, 1, 1, 1, 0 }, 472 { "System", 25, 1, 1, 1, 0 }, 473 { "PWM Phase1", 26, 1, 1, 1, 0 }, 474 { "PWM Phase2", 27, 1, 1, 1, 0 }, 475 { "PWM Phase3", 28, 1, 1, 1, 0 }, 476 { "PWM Phase4", 29, 1, 1, 1, 0 }, 477 { "PWM Phase5", 30, 1, 1, 1, 0 }, 478 { "CPU Fan", 32, 2, 60, 1, 0 }, 479 { "SYS Fan", 34, 2, 60, 1, 0 }, 480 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 481 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 482 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 483 { NULL, 0, 0, 0, 0, 0 } } 484 }, 485 { 0x0019, "IN9 32X MAX", { 486 { "CPU Core", 7, 0, 10, 1, 0 }, 487 { "DDR2", 13, 0, 20, 1, 0 }, 488 { "DDR2 VTT", 14, 0, 10, 1, 0 }, 489 { "CPU VTT", 3, 0, 20, 1, 0 }, 490 { "NB 1.2V", 4, 0, 10, 1, 0 }, 491 { "SB 1.5V", 6, 0, 10, 1, 0 }, 492 { "HyperTransport", 5, 0, 10, 1, 0 }, 493 { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 }, 494 { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, 495 { "ATX +5V", 9, 0, 30, 1, 0 }, 496 { "ATX +3.3V", 10, 0, 20, 1, 0 }, 497 { "ATX 5VSB", 11, 0, 30, 1, 0 }, 498 { "CPU", 24, 1, 1, 1, 0 }, 499 { "System", 25, 1, 1, 1, 0 }, 500 { "PWM Phase1", 26, 1, 1, 1, 0 }, 501 { "PWM Phase2", 27, 1, 1, 1, 0 }, 502 { "PWM Phase3", 28, 1, 1, 1, 0 }, 503 { "PWM Phase4", 29, 1, 1, 1, 0 }, 504 { "PWM Phase5", 30, 1, 1, 1, 0 }, 505 { "CPU FAN", 32, 2, 60, 1, 0 }, 506 { "SYS FAN", 34, 2, 60, 1, 0 }, 507 { "AUX1 FAN", 33, 2, 60, 1, 0 }, 508 { "AUX2 FAN", 35, 2, 60, 1, 0 }, 509 { "AUX3 FAN", 36, 2, 60, 1, 0 }, 510 { NULL, 0, 0, 0, 0, 0 } } 511 }, 512 { 0x001A, "IP35 Pro", { 513 { "CPU Core", 0, 0, 10, 1, 0 }, 514 { "DDR2", 1, 0, 20, 1, 0 }, 515 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 516 { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, 517 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 518 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 519 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 520 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 521 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 522 { "ATX +5V", 9, 0, 30, 1, 0 }, 523 { "+3.3V", 10, 0, 20, 1, 0 }, 524 { "5VSB", 11, 0, 30, 1, 0 }, 525 { "CPU", 24, 1, 1, 1, 0 }, 526 { "System", 25, 1, 1, 1, 0 }, 527 { "PWM", 26, 1, 1, 1, 0 }, 528 { "PWM Phase2", 27, 1, 1, 1, 0 }, 529 { "PWM Phase3", 28, 1, 1, 1, 0 }, 530 { "PWM Phase4", 29, 1, 1, 1, 0 }, 531 { "PWM Phase5", 30, 1, 1, 1, 0 }, 532 { "CPU Fan", 32, 2, 60, 1, 0 }, 533 { "SYS Fan", 34, 2, 60, 1, 0 }, 534 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 535 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 536 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 537 { "AUX4 Fan", 37, 2, 60, 1, 0 }, 538 { NULL, 0, 0, 0, 0, 0 } } 539 }, 540 { 0x001B, NULL /* Unknown, need DMI string */, { 541 { "CPU Core", 0, 0, 10, 1, 0 }, 542 { "DDR3", 1, 0, 20, 1, 0 }, 543 { "DDR3 VTT", 2, 0, 10, 1, 0 }, 544 { "CPU VTT", 3, 0, 10, 1, 0 }, 545 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 546 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 547 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 548 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 549 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 550 { "ATX +5V", 9, 0, 30, 1, 0 }, 551 { "+3.3V", 10, 0, 20, 1, 0 }, 552 { "5VSB", 11, 0, 30, 1, 0 }, 553 { "CPU", 24, 1, 1, 1, 0 }, 554 { "System", 25, 1, 1, 1, 0 }, 555 { "PWM Phase1", 26, 1, 1, 1, 0 }, 556 { "PWM Phase2", 27, 1, 1, 1, 0 }, 557 { "PWM Phase3", 28, 1, 1, 1, 0 }, 558 { "PWM Phase4", 29, 1, 1, 1, 0 }, 559 { "PWM Phase5", 30, 1, 1, 1, 0 }, 560 { "CPU Fan", 32, 2, 60, 1, 0 }, 561 { "SYS Fan", 34, 2, 60, 1, 0 }, 562 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 563 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 564 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 565 { NULL, 0, 0, 0, 0, 0 } } 566 }, 567 { 0x001C, NULL /* Unknown, need DMI string */, { 568 { "CPU Core", 0, 0, 10, 1, 0 }, 569 { "DDR2", 1, 0, 20, 1, 0 }, 570 { "DDR2 VTT", 2, 0, 10, 1, 0 }, 571 { "CPU VTT", 3, 0, 10, 1, 0 }, 572 { "MCH 1.25V", 4, 0, 10, 1, 0 }, 573 { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, 574 { "ICH 1.05V", 6, 0, 10, 1, 0 }, 575 { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, 576 { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, 577 { "ATX +5V", 9, 0, 30, 1, 0 }, 578 { "+3.3V", 10, 0, 20, 1, 0 }, 579 { "5VSB", 11, 0, 30, 1, 0 }, 580 { "CPU", 24, 1, 1, 1, 0 }, 581 { "System", 25, 1, 1, 1, 0 }, 582 { "PWM Phase1", 26, 1, 1, 1, 0 }, 583 { "PWM Phase2", 27, 1, 1, 1, 0 }, 584 { "PWM Phase3", 28, 1, 1, 1, 0 }, 585 { "PWM Phase4", 29, 1, 1, 1, 0 }, 586 { "PWM Phase5", 30, 1, 1, 1, 0 }, 587 { "CPU Fan", 32, 2, 60, 1, 0 }, 588 { "SYS Fan", 34, 2, 60, 1, 0 }, 589 { "AUX1 Fan", 33, 2, 60, 1, 0 }, 590 { "AUX2 Fan", 35, 2, 60, 1, 0 }, 591 { "AUX3 Fan", 36, 2, 60, 1, 0 }, 592 { NULL, 0, 0, 0, 0, 0 } } 593 }, 594 { 0x0000, NULL, { { NULL, 0, 0, 0, 0, 0 } } } 595 }; 596 597 598 /* Insmod parameters */ 599 static int force; 600 module_param(force, bool, 0); 601 MODULE_PARM_DESC(force, "Set to one to force detection."); 602 /* Default verbose is 1, since this driver is still in the testing phase */ 603 static int verbose = 1; 604 module_param(verbose, bool, 0644); 605 MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting"); 606 607 608 /* wait while the uguru is busy (usually after a write) */ 609 static int abituguru3_wait_while_busy(struct abituguru3_data *data) 610 { 611 u8 x; 612 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 613 614 while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 615 ABIT_UGURU3_STATUS_BUSY) { 616 timeout--; 617 if (timeout == 0) 618 return x; 619 /* sleep a bit before our last try, to give the uGuru3 one 620 last chance to respond. */ 621 if (timeout == 1) 622 msleep(1); 623 } 624 return ABIT_UGURU3_SUCCESS; 625 } 626 627 /* wait till uguru is ready to be read */ 628 static int abituguru3_wait_for_read(struct abituguru3_data *data) 629 { 630 u8 x; 631 int timeout = ABIT_UGURU3_WAIT_TIMEOUT; 632 633 while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & 634 ABIT_UGURU3_STATUS_READY_FOR_READ)) { 635 timeout--; 636 if (timeout == 0) 637 return x; 638 /* sleep a bit before our last try, to give the uGuru3 one 639 last chance to respond. */ 640 if (timeout == 1) 641 msleep(1); 642 } 643 return ABIT_UGURU3_SUCCESS; 644 } 645 646 /* This synchronizes us with the uGuru3's protocol state machine, this 647 must be done before each command. */ 648 static int abituguru3_synchronize(struct abituguru3_data *data) 649 { 650 int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT; 651 652 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 653 ABIT_UGURU3_DEBUG("synchronize timeout during initial busy " 654 "wait, status: 0x%02x\n", x); 655 return -EIO; 656 } 657 658 outb(0x20, data->addr + ABIT_UGURU3_DATA); 659 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 660 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, " 661 "status: 0x%02x\n", x); 662 return -EIO; 663 } 664 665 outb(0x10, data->addr + ABIT_UGURU3_CMD); 666 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 667 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, " 668 "status: 0x%02x\n", x); 669 return -EIO; 670 } 671 672 outb(0x00, data->addr + ABIT_UGURU3_CMD); 673 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 674 ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, " 675 "status: 0x%02x\n", x); 676 return -EIO; 677 } 678 679 if ((x = abituguru3_wait_for_read(data)) != ABIT_UGURU3_SUCCESS) { 680 ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, " 681 "status: 0x%02x\n", x); 682 return -EIO; 683 } 684 685 while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) { 686 timeout--; 687 if (timeout == 0) { 688 ABIT_UGURU3_DEBUG("synchronize timeout cmd does not " 689 "hold 0xAC after synchronize, cmd: 0x%02x\n", 690 x); 691 return -EIO; 692 } 693 msleep(1); 694 } 695 return 0; 696 } 697 698 /* Read count bytes from sensor sensor_addr in bank bank_addr and store the 699 result in buf */ 700 static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset, 701 u8 count, u8 *buf) 702 { 703 int i, x; 704 705 if ((x = abituguru3_synchronize(data))) 706 return x; 707 708 outb(0x1A, data->addr + ABIT_UGURU3_DATA); 709 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 710 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 711 "sending 0x1A, status: 0x%02x\n", (unsigned int)bank, 712 (unsigned int)offset, x); 713 return -EIO; 714 } 715 716 outb(bank, data->addr + ABIT_UGURU3_CMD); 717 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 718 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 719 "sending the bank, status: 0x%02x\n", 720 (unsigned int)bank, (unsigned int)offset, x); 721 return -EIO; 722 } 723 724 outb(offset, data->addr + ABIT_UGURU3_CMD); 725 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 726 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 727 "sending the offset, status: 0x%02x\n", 728 (unsigned int)bank, (unsigned int)offset, x); 729 return -EIO; 730 } 731 732 outb(count, data->addr + ABIT_UGURU3_CMD); 733 if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { 734 ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " 735 "sending the count, status: 0x%02x\n", 736 (unsigned int)bank, (unsigned int)offset, x); 737 return -EIO; 738 } 739 740 for (i = 0; i < count; i++) { 741 if ((x = abituguru3_wait_for_read(data)) != 742 ABIT_UGURU3_SUCCESS) { 743 ABIT_UGURU3_DEBUG("timeout reading byte %d from " 744 "0x%02x:0x%02x, status: 0x%02x\n", i, 745 (unsigned int)bank, (unsigned int)offset, x); 746 break; 747 } 748 buf[i] = inb(data->addr + ABIT_UGURU3_CMD); 749 } 750 return i; 751 } 752 753 /* Sensor settings are stored 1 byte per offset with the bytes 754 placed add consecutive offsets. */ 755 static int abituguru3_read_increment_offset(struct abituguru3_data *data, 756 u8 bank, u8 offset, u8 count, 757 u8 *buf, int offset_count) 758 { 759 int i, x; 760 761 for (i = 0; i < offset_count; i++) 762 if ((x = abituguru3_read(data, bank, offset + i, count, 763 buf + i * count)) != count) { 764 if (x < 0) 765 return x; 766 return i * count + x; 767 } 768 769 return i * count; 770 } 771 772 /* Following are the sysfs callback functions. These functions expect: 773 sensor_device_attribute_2->index: index into the data->sensors array 774 sensor_device_attribute_2->nr: register offset, bitmask or NA. */ 775 static struct abituguru3_data *abituguru3_update_device(struct device *dev); 776 777 static ssize_t show_value(struct device *dev, 778 struct device_attribute *devattr, char *buf) 779 { 780 int value; 781 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 782 struct abituguru3_data *data = abituguru3_update_device(dev); 783 const struct abituguru3_sensor_info *sensor; 784 785 if (!data) 786 return -EIO; 787 788 sensor = &data->sensors[attr->index]; 789 790 /* are we reading a setting, or is this a normal read? */ 791 if (attr->nr) 792 value = data->settings[sensor->port][attr->nr]; 793 else 794 value = data->value[sensor->port]; 795 796 /* convert the value */ 797 value = (value * sensor->multiplier) / sensor->divisor + 798 sensor->offset; 799 800 /* alternatively we could update the sensors settings struct for this, 801 but then its contents would differ from the windows sw ini files */ 802 if (sensor->type == ABIT_UGURU3_TEMP_SENSOR) 803 value *= 1000; 804 805 return sprintf(buf, "%d\n", value); 806 } 807 808 static ssize_t show_alarm(struct device *dev, 809 struct device_attribute *devattr, char *buf) 810 { 811 int port; 812 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 813 struct abituguru3_data *data = abituguru3_update_device(dev); 814 815 if (!data) 816 return -EIO; 817 818 port = data->sensors[attr->index].port; 819 820 /* See if the alarm bit for this sensor is set and if a bitmask is 821 given in attr->nr also check if the alarm matches the type of alarm 822 we're looking for (for volt it can be either low or high). The type 823 is stored in a few readonly bits in the settings of the sensor. */ 824 if ((data->alarms[port / 8] & (0x01 << (port % 8))) && 825 (!attr->nr || (data->settings[port][0] & attr->nr))) 826 return sprintf(buf, "1\n"); 827 else 828 return sprintf(buf, "0\n"); 829 } 830 831 static ssize_t show_mask(struct device *dev, 832 struct device_attribute *devattr, char *buf) 833 { 834 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 835 struct abituguru3_data *data = dev_get_drvdata(dev); 836 837 if (data->settings[data->sensors[attr->index].port][0] & attr->nr) 838 return sprintf(buf, "1\n"); 839 else 840 return sprintf(buf, "0\n"); 841 } 842 843 static ssize_t show_label(struct device *dev, 844 struct device_attribute *devattr, char *buf) 845 { 846 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); 847 struct abituguru3_data *data = dev_get_drvdata(dev); 848 849 return sprintf(buf, "%s\n", data->sensors[attr->index].name); 850 } 851 852 static ssize_t show_name(struct device *dev, 853 struct device_attribute *devattr, char *buf) 854 { 855 return sprintf(buf, "%s\n", ABIT_UGURU3_NAME); 856 } 857 858 /* Sysfs attr templates, the real entries are generated automatically. */ 859 static const 860 struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { { 861 SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0), 862 SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0), 863 SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0), 864 SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL, 865 ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0), 866 SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL, 867 ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0), 868 SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL, 869 ABIT_UGURU3_BEEP_ENABLE, 0), 870 SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL, 871 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 872 SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL, 873 ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0), 874 SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL, 875 ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0), 876 SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0) 877 }, { 878 SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0), 879 SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0), 880 SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0), 881 SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0), 882 SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL, 883 ABIT_UGURU3_BEEP_ENABLE, 0), 884 SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL, 885 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 886 SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL, 887 ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0), 888 SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0) 889 }, { 890 SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0), 891 SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0), 892 SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0), 893 SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL, 894 ABIT_UGURU3_BEEP_ENABLE, 0), 895 SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL, 896 ABIT_UGURU3_SHUTDOWN_ENABLE, 0), 897 SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL, 898 ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0), 899 SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0) 900 } }; 901 902 static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = { 903 SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0), 904 }; 905 906 static int __devinit abituguru3_probe(struct platform_device *pdev) 907 { 908 const int no_sysfs_attr[3] = { 10, 8, 7 }; 909 int sensor_index[3] = { 0, 1, 1 }; 910 struct abituguru3_data *data; 911 int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV; 912 char *sysfs_filename; 913 u8 buf[2]; 914 u16 id; 915 916 if (!(data = kzalloc(sizeof(struct abituguru3_data), GFP_KERNEL))) 917 return -ENOMEM; 918 919 data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start; 920 mutex_init(&data->update_lock); 921 platform_set_drvdata(pdev, data); 922 923 /* Read the motherboard ID */ 924 if ((i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, 925 ABIT_UGURU3_BOARD_ID, 2, buf)) != 2) { 926 goto abituguru3_probe_error; 927 } 928 929 /* Completely read the uGuru to see if one really is there */ 930 if (!abituguru3_update_device(&pdev->dev)) 931 goto abituguru3_probe_error; 932 933 /* lookup the ID in our motherboard table */ 934 id = ((u16)buf[0] << 8) | (u16)buf[1]; 935 for (i = 0; abituguru3_motherboards[i].id; i++) 936 if (abituguru3_motherboards[i].id == id) 937 break; 938 if (!abituguru3_motherboards[i].id) { 939 printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard " 940 "ID: %04X. Please report this to the abituguru3 " 941 "maintainer (see MAINTAINERS)\n", (unsigned int)id); 942 goto abituguru3_probe_error; 943 } 944 data->sensors = abituguru3_motherboards[i].sensors; 945 946 printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard " 947 "ID: %04X\n", (unsigned int)id); 948 949 #ifdef CONFIG_DMI 950 if (!abituguru3_motherboards[i].dmi_name) { 951 printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was " 952 "not detected using DMI. Please send the output of " 953 "\"dmidecode\" to the abituguru3 maintainer " 954 "(see MAINTAINERS)\n"); 955 } 956 #endif 957 958 /* Fill the sysfs attr array */ 959 sysfs_attr_i = 0; 960 sysfs_filename = data->sysfs_names; 961 sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH; 962 for (i = 0; data->sensors[i].name; i++) { 963 /* Fail safe check, this should never happen! */ 964 if (i >= ABIT_UGURU3_MAX_NO_SENSORS) { 965 printk(KERN_ERR ABIT_UGURU3_NAME 966 ": Fatal error motherboard has more sensors " 967 "then ABIT_UGURU3_MAX_NO_SENSORS. This should " 968 "never happen please report to the abituguru3 " 969 "maintainer (see MAINTAINERS)\n"); 970 res = -ENAMETOOLONG; 971 goto abituguru3_probe_error; 972 } 973 type = data->sensors[i].type; 974 for (j = 0; j < no_sysfs_attr[type]; j++) { 975 used = snprintf(sysfs_filename, sysfs_names_free, 976 abituguru3_sysfs_templ[type][j].dev_attr.attr. 977 name, sensor_index[type]) + 1; 978 data->sysfs_attr[sysfs_attr_i] = 979 abituguru3_sysfs_templ[type][j]; 980 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name = 981 sysfs_filename; 982 data->sysfs_attr[sysfs_attr_i].index = i; 983 sysfs_filename += used; 984 sysfs_names_free -= used; 985 sysfs_attr_i++; 986 } 987 sensor_index[type]++; 988 } 989 /* Fail safe check, this should never happen! */ 990 if (sysfs_names_free < 0) { 991 printk(KERN_ERR ABIT_UGURU3_NAME 992 ": Fatal error ran out of space for sysfs attr names. " 993 "This should never happen please report to the " 994 "abituguru3 maintainer (see MAINTAINERS)\n"); 995 res = -ENAMETOOLONG; 996 goto abituguru3_probe_error; 997 } 998 999 /* Register sysfs hooks */ 1000 for (i = 0; i < sysfs_attr_i; i++) 1001 if (device_create_file(&pdev->dev, 1002 &data->sysfs_attr[i].dev_attr)) 1003 goto abituguru3_probe_error; 1004 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1005 if (device_create_file(&pdev->dev, 1006 &abituguru3_sysfs_attr[i].dev_attr)) 1007 goto abituguru3_probe_error; 1008 1009 data->hwmon_dev = hwmon_device_register(&pdev->dev); 1010 if (IS_ERR(data->hwmon_dev)) { 1011 res = PTR_ERR(data->hwmon_dev); 1012 goto abituguru3_probe_error; 1013 } 1014 1015 return 0; /* success */ 1016 1017 abituguru3_probe_error: 1018 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1019 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1020 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1021 device_remove_file(&pdev->dev, 1022 &abituguru3_sysfs_attr[i].dev_attr); 1023 kfree(data); 1024 return res; 1025 } 1026 1027 static int __devexit abituguru3_remove(struct platform_device *pdev) 1028 { 1029 int i; 1030 struct abituguru3_data *data = platform_get_drvdata(pdev); 1031 1032 platform_set_drvdata(pdev, NULL); 1033 hwmon_device_unregister(data->hwmon_dev); 1034 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) 1035 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); 1036 for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) 1037 device_remove_file(&pdev->dev, 1038 &abituguru3_sysfs_attr[i].dev_attr); 1039 kfree(data); 1040 1041 return 0; 1042 } 1043 1044 static struct abituguru3_data *abituguru3_update_device(struct device *dev) 1045 { 1046 int i; 1047 struct abituguru3_data *data = dev_get_drvdata(dev); 1048 1049 mutex_lock(&data->update_lock); 1050 if (!data->valid || time_after(jiffies, data->last_updated + HZ)) { 1051 /* Clear data->valid while updating */ 1052 data->valid = 0; 1053 /* Read alarms */ 1054 if (abituguru3_read_increment_offset(data, 1055 ABIT_UGURU3_SETTINGS_BANK, 1056 ABIT_UGURU3_ALARMS_START, 1057 1, data->alarms, 48/8) != (48/8)) 1058 goto LEAVE_UPDATE; 1059 /* Read in and temp sensors (3 byte settings / sensor) */ 1060 for (i = 0; i < 32; i++) { 1061 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1062 ABIT_UGURU3_VALUES_START + i, 1063 1, &data->value[i]) != 1) 1064 goto LEAVE_UPDATE; 1065 if (abituguru3_read_increment_offset(data, 1066 ABIT_UGURU3_SETTINGS_BANK, 1067 ABIT_UGURU3_SETTINGS_START + i * 3, 1068 1, 1069 data->settings[i], 3) != 3) 1070 goto LEAVE_UPDATE; 1071 } 1072 /* Read temp sensors (2 byte settings / sensor) */ 1073 for (i = 0; i < 16; i++) { 1074 if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, 1075 ABIT_UGURU3_VALUES_START + 32 + i, 1076 1, &data->value[32 + i]) != 1) 1077 goto LEAVE_UPDATE; 1078 if (abituguru3_read_increment_offset(data, 1079 ABIT_UGURU3_SETTINGS_BANK, 1080 ABIT_UGURU3_SETTINGS_START + 32 * 3 + 1081 i * 2, 1, 1082 data->settings[32 + i], 2) != 2) 1083 goto LEAVE_UPDATE; 1084 } 1085 data->last_updated = jiffies; 1086 data->valid = 1; 1087 } 1088 LEAVE_UPDATE: 1089 mutex_unlock(&data->update_lock); 1090 if (data->valid) 1091 return data; 1092 else 1093 return NULL; 1094 } 1095 1096 #ifdef CONFIG_PM 1097 static int abituguru3_suspend(struct platform_device *pdev, pm_message_t state) 1098 { 1099 struct abituguru3_data *data = platform_get_drvdata(pdev); 1100 /* make sure all communications with the uguru3 are done and no new 1101 ones are started */ 1102 mutex_lock(&data->update_lock); 1103 return 0; 1104 } 1105 1106 static int abituguru3_resume(struct platform_device *pdev) 1107 { 1108 struct abituguru3_data *data = platform_get_drvdata(pdev); 1109 mutex_unlock(&data->update_lock); 1110 return 0; 1111 } 1112 #else 1113 #define abituguru3_suspend NULL 1114 #define abituguru3_resume NULL 1115 #endif /* CONFIG_PM */ 1116 1117 static struct platform_driver abituguru3_driver = { 1118 .driver = { 1119 .owner = THIS_MODULE, 1120 .name = ABIT_UGURU3_NAME, 1121 }, 1122 .probe = abituguru3_probe, 1123 .remove = __devexit_p(abituguru3_remove), 1124 .suspend = abituguru3_suspend, 1125 .resume = abituguru3_resume 1126 }; 1127 1128 #ifdef CONFIG_DMI 1129 1130 static int __init abituguru3_dmi_detect(void) 1131 { 1132 const char *board_vendor, *board_name; 1133 int i, err = (force) ? 1 : -ENODEV; 1134 size_t sublen; 1135 1136 board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); 1137 if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/")) 1138 return err; 1139 1140 board_name = dmi_get_system_info(DMI_BOARD_NAME); 1141 if (!board_name) 1142 return err; 1143 1144 /* At the moment, we don't care about the part of the vendor 1145 * DMI string contained in brackets. Truncate the string at 1146 * the first occurrence of a bracket. Trim any trailing space 1147 * from the substring. 1148 */ 1149 sublen = strcspn(board_name, "("); 1150 while (sublen > 0 && board_name[sublen - 1] == ' ') 1151 sublen--; 1152 1153 for (i = 0; abituguru3_motherboards[i].id; i++) { 1154 const char *dmi_name = abituguru3_motherboards[i].dmi_name; 1155 if (!dmi_name || strlen(dmi_name) != sublen) 1156 continue; 1157 if (!strncasecmp(board_name, dmi_name, sublen)) 1158 break; 1159 } 1160 1161 if (!abituguru3_motherboards[i].id) 1162 return 1; 1163 1164 return 0; 1165 } 1166 1167 #else /* !CONFIG_DMI */ 1168 1169 static inline int abituguru3_dmi_detect(void) 1170 { 1171 return 1; 1172 } 1173 1174 #endif /* CONFIG_DMI */ 1175 1176 /* FIXME: Manual detection should die eventually; we need to collect stable 1177 * DMI model names first before we can rely entirely on CONFIG_DMI. 1178 */ 1179 1180 static int __init abituguru3_detect(void) 1181 { 1182 /* See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or 1183 0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05 1184 or 0x55 at CMD instead, why is unknown. */ 1185 u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA); 1186 u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD); 1187 if (((data_val == 0x00) || (data_val == 0x08)) && 1188 ((cmd_val == 0xAC) || (cmd_val == 0x05) || 1189 (cmd_val == 0x55))) 1190 return 0; 1191 1192 ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " 1193 "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); 1194 1195 if (force) { 1196 printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is " 1197 "present because of \"force\" parameter\n"); 1198 return 0; 1199 } 1200 1201 /* No uGuru3 found */ 1202 return -ENODEV; 1203 } 1204 1205 static struct platform_device *abituguru3_pdev; 1206 1207 static int __init abituguru3_init(void) 1208 { 1209 struct resource res = { .flags = IORESOURCE_IO }; 1210 int err; 1211 1212 /* Attempt DMI detection first */ 1213 err = abituguru3_dmi_detect(); 1214 if (err < 0) 1215 return err; 1216 1217 /* Fall back to manual detection if there was no exact 1218 * board name match, or force was specified. 1219 */ 1220 if (err > 0) { 1221 err = abituguru3_detect(); 1222 if (err) 1223 return err; 1224 } 1225 1226 err = platform_driver_register(&abituguru3_driver); 1227 if (err) 1228 goto exit; 1229 1230 abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, 1231 ABIT_UGURU3_BASE); 1232 if (!abituguru3_pdev) { 1233 printk(KERN_ERR ABIT_UGURU3_NAME 1234 ": Device allocation failed\n"); 1235 err = -ENOMEM; 1236 goto exit_driver_unregister; 1237 } 1238 1239 res.start = ABIT_UGURU3_BASE; 1240 res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1; 1241 res.name = ABIT_UGURU3_NAME; 1242 1243 err = platform_device_add_resources(abituguru3_pdev, &res, 1); 1244 if (err) { 1245 printk(KERN_ERR ABIT_UGURU3_NAME 1246 ": Device resource addition failed (%d)\n", err); 1247 goto exit_device_put; 1248 } 1249 1250 err = platform_device_add(abituguru3_pdev); 1251 if (err) { 1252 printk(KERN_ERR ABIT_UGURU3_NAME 1253 ": Device addition failed (%d)\n", err); 1254 goto exit_device_put; 1255 } 1256 1257 return 0; 1258 1259 exit_device_put: 1260 platform_device_put(abituguru3_pdev); 1261 exit_driver_unregister: 1262 platform_driver_unregister(&abituguru3_driver); 1263 exit: 1264 return err; 1265 } 1266 1267 static void __exit abituguru3_exit(void) 1268 { 1269 platform_device_unregister(abituguru3_pdev); 1270 platform_driver_unregister(&abituguru3_driver); 1271 } 1272 1273 MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>"); 1274 MODULE_DESCRIPTION("Abit uGuru3 Sensor device"); 1275 MODULE_LICENSE("GPL"); 1276 1277 module_init(abituguru3_init); 1278 module_exit(abituguru3_exit); 1279