1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * HID driver for Nintendo Switch Joy-Cons and Pro Controllers 4 * 5 * Copyright (c) 2019-2021 Daniel J. Ogorchock <djogorchock@gmail.com> 6 * 7 * The following resources/projects were referenced for this driver: 8 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 9 * https://gitlab.com/pjranki/joycon-linux-kernel (Peter Rankin) 10 * https://github.com/FrotBot/SwitchProConLinuxUSB 11 * https://github.com/MTCKC/ProconXInput 12 * https://github.com/Davidobot/BetterJoyForCemu 13 * hid-wiimote kernel hid driver 14 * hid-logitech-hidpp driver 15 * hid-sony driver 16 * 17 * This driver supports the Nintendo Switch Joy-Cons and Pro Controllers. The 18 * Pro Controllers can either be used over USB or Bluetooth. 19 * 20 * The driver will retrieve the factory calibration info from the controllers, 21 * so little to no user calibration should be required. 22 * 23 */ 24 25 #include "hid-ids.h" 26 #include <asm/unaligned.h> 27 #include <linux/delay.h> 28 #include <linux/device.h> 29 #include <linux/kernel.h> 30 #include <linux/hid.h> 31 #include <linux/input.h> 32 #include <linux/jiffies.h> 33 #include <linux/leds.h> 34 #include <linux/module.h> 35 #include <linux/power_supply.h> 36 #include <linux/spinlock.h> 37 38 /* 39 * Reference the url below for the following HID report defines: 40 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 41 */ 42 43 /* Output Reports */ 44 #define JC_OUTPUT_RUMBLE_AND_SUBCMD 0x01 45 #define JC_OUTPUT_FW_UPDATE_PKT 0x03 46 #define JC_OUTPUT_RUMBLE_ONLY 0x10 47 #define JC_OUTPUT_MCU_DATA 0x11 48 #define JC_OUTPUT_USB_CMD 0x80 49 50 /* Subcommand IDs */ 51 #define JC_SUBCMD_STATE 0x00 52 #define JC_SUBCMD_MANUAL_BT_PAIRING 0x01 53 #define JC_SUBCMD_REQ_DEV_INFO 0x02 54 #define JC_SUBCMD_SET_REPORT_MODE 0x03 55 #define JC_SUBCMD_TRIGGERS_ELAPSED 0x04 56 #define JC_SUBCMD_GET_PAGE_LIST_STATE 0x05 57 #define JC_SUBCMD_SET_HCI_STATE 0x06 58 #define JC_SUBCMD_RESET_PAIRING_INFO 0x07 59 #define JC_SUBCMD_LOW_POWER_MODE 0x08 60 #define JC_SUBCMD_SPI_FLASH_READ 0x10 61 #define JC_SUBCMD_SPI_FLASH_WRITE 0x11 62 #define JC_SUBCMD_RESET_MCU 0x20 63 #define JC_SUBCMD_SET_MCU_CONFIG 0x21 64 #define JC_SUBCMD_SET_MCU_STATE 0x22 65 #define JC_SUBCMD_SET_PLAYER_LIGHTS 0x30 66 #define JC_SUBCMD_GET_PLAYER_LIGHTS 0x31 67 #define JC_SUBCMD_SET_HOME_LIGHT 0x38 68 #define JC_SUBCMD_ENABLE_IMU 0x40 69 #define JC_SUBCMD_SET_IMU_SENSITIVITY 0x41 70 #define JC_SUBCMD_WRITE_IMU_REG 0x42 71 #define JC_SUBCMD_READ_IMU_REG 0x43 72 #define JC_SUBCMD_ENABLE_VIBRATION 0x48 73 #define JC_SUBCMD_GET_REGULATED_VOLTAGE 0x50 74 75 /* Input Reports */ 76 #define JC_INPUT_BUTTON_EVENT 0x3F 77 #define JC_INPUT_SUBCMD_REPLY 0x21 78 #define JC_INPUT_IMU_DATA 0x30 79 #define JC_INPUT_MCU_DATA 0x31 80 #define JC_INPUT_USB_RESPONSE 0x81 81 82 /* Feature Reports */ 83 #define JC_FEATURE_LAST_SUBCMD 0x02 84 #define JC_FEATURE_OTA_FW_UPGRADE 0x70 85 #define JC_FEATURE_SETUP_MEM_READ 0x71 86 #define JC_FEATURE_MEM_READ 0x72 87 #define JC_FEATURE_ERASE_MEM_SECTOR 0x73 88 #define JC_FEATURE_MEM_WRITE 0x74 89 #define JC_FEATURE_LAUNCH 0x75 90 91 /* USB Commands */ 92 #define JC_USB_CMD_CONN_STATUS 0x01 93 #define JC_USB_CMD_HANDSHAKE 0x02 94 #define JC_USB_CMD_BAUDRATE_3M 0x03 95 #define JC_USB_CMD_NO_TIMEOUT 0x04 96 #define JC_USB_CMD_EN_TIMEOUT 0x05 97 #define JC_USB_RESET 0x06 98 #define JC_USB_PRE_HANDSHAKE 0x91 99 #define JC_USB_SEND_UART 0x92 100 101 /* Magic value denoting presence of user calibration */ 102 #define JC_CAL_USR_MAGIC_0 0xB2 103 #define JC_CAL_USR_MAGIC_1 0xA1 104 #define JC_CAL_USR_MAGIC_SIZE 2 105 106 /* SPI storage addresses of user calibration data */ 107 #define JC_CAL_USR_LEFT_MAGIC_ADDR 0x8010 108 #define JC_CAL_USR_LEFT_DATA_ADDR 0x8012 109 #define JC_CAL_USR_LEFT_DATA_END 0x801A 110 #define JC_CAL_USR_RIGHT_MAGIC_ADDR 0x801B 111 #define JC_CAL_USR_RIGHT_DATA_ADDR 0x801D 112 #define JC_CAL_STICK_DATA_SIZE \ 113 (JC_CAL_USR_LEFT_DATA_END - JC_CAL_USR_LEFT_DATA_ADDR + 1) 114 115 /* SPI storage addresses of factory calibration data */ 116 #define JC_CAL_FCT_DATA_LEFT_ADDR 0x603d 117 #define JC_CAL_FCT_DATA_RIGHT_ADDR 0x6046 118 119 /* SPI storage addresses of IMU factory calibration data */ 120 #define JC_IMU_CAL_FCT_DATA_ADDR 0x6020 121 #define JC_IMU_CAL_FCT_DATA_END 0x6037 122 #define JC_IMU_CAL_DATA_SIZE \ 123 (JC_IMU_CAL_FCT_DATA_END - JC_IMU_CAL_FCT_DATA_ADDR + 1) 124 /* SPI storage addresses of IMU user calibration data */ 125 #define JC_IMU_CAL_USR_MAGIC_ADDR 0x8026 126 #define JC_IMU_CAL_USR_DATA_ADDR 0x8028 127 128 /* The raw analog joystick values will be mapped in terms of this magnitude */ 129 #define JC_MAX_STICK_MAG 32767 130 #define JC_STICK_FUZZ 250 131 #define JC_STICK_FLAT 500 132 133 /* Hat values for pro controller's d-pad */ 134 #define JC_MAX_DPAD_MAG 1 135 #define JC_DPAD_FUZZ 0 136 #define JC_DPAD_FLAT 0 137 138 /* Under most circumstances IMU reports are pushed every 15ms; use as default */ 139 #define JC_IMU_DFLT_AVG_DELTA_MS 15 140 /* How many samples to sum before calculating average IMU report delta */ 141 #define JC_IMU_SAMPLES_PER_DELTA_AVG 300 142 /* Controls how many dropped IMU packets at once trigger a warning message */ 143 #define JC_IMU_DROPPED_PKT_WARNING 3 144 145 /* 146 * The controller's accelerometer has a sensor resolution of 16bits and is 147 * configured with a range of +-8000 milliGs. Therefore, the resolution can be 148 * calculated thus: (2^16-1)/(8000 * 2) = 4.096 digits per milliG 149 * Resolution per G (rather than per millliG): 4.096 * 1000 = 4096 digits per G 150 * Alternatively: 1/4096 = .0002441 Gs per digit 151 */ 152 #define JC_IMU_MAX_ACCEL_MAG 32767 153 #define JC_IMU_ACCEL_RES_PER_G 4096 154 #define JC_IMU_ACCEL_FUZZ 10 155 #define JC_IMU_ACCEL_FLAT 0 156 157 /* 158 * The controller's gyroscope has a sensor resolution of 16bits and is 159 * configured with a range of +-2000 degrees/second. 160 * Digits per dps: (2^16 -1)/(2000*2) = 16.38375 161 * dps per digit: 16.38375E-1 = .0610 162 * 163 * STMicro recommends in the datasheet to add 15% to the dps/digit. This allows 164 * the full sensitivity range to be saturated without clipping. This yields more 165 * accurate results, so it's the technique this driver uses. 166 * dps per digit (corrected): .0610 * 1.15 = .0702 167 * digits per dps (corrected): .0702E-1 = 14.247 168 * 169 * Now, 14.247 truncating to 14 loses a lot of precision, so we rescale the 170 * min/max range by 1000. 171 */ 172 #define JC_IMU_PREC_RANGE_SCALE 1000 173 /* Note: change mag and res_per_dps if prec_range_scale is ever altered */ 174 #define JC_IMU_MAX_GYRO_MAG 32767000 /* (2^16-1)*1000 */ 175 #define JC_IMU_GYRO_RES_PER_DPS 14247 /* (14.247*1000) */ 176 #define JC_IMU_GYRO_FUZZ 10 177 #define JC_IMU_GYRO_FLAT 0 178 179 /* frequency/amplitude tables for rumble */ 180 struct joycon_rumble_freq_data { 181 u16 high; 182 u8 low; 183 u16 freq; /* Hz*/ 184 }; 185 186 struct joycon_rumble_amp_data { 187 u8 high; 188 u16 low; 189 u16 amp; 190 }; 191 192 #if IS_ENABLED(CONFIG_NINTENDO_FF) 193 /* 194 * These tables are from 195 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering/blob/master/rumble_data_table.md 196 */ 197 static const struct joycon_rumble_freq_data joycon_rumble_frequencies[] = { 198 /* high, low, freq */ 199 { 0x0000, 0x01, 41 }, { 0x0000, 0x02, 42 }, { 0x0000, 0x03, 43 }, 200 { 0x0000, 0x04, 44 }, { 0x0000, 0x05, 45 }, { 0x0000, 0x06, 46 }, 201 { 0x0000, 0x07, 47 }, { 0x0000, 0x08, 48 }, { 0x0000, 0x09, 49 }, 202 { 0x0000, 0x0A, 50 }, { 0x0000, 0x0B, 51 }, { 0x0000, 0x0C, 52 }, 203 { 0x0000, 0x0D, 53 }, { 0x0000, 0x0E, 54 }, { 0x0000, 0x0F, 55 }, 204 { 0x0000, 0x10, 57 }, { 0x0000, 0x11, 58 }, { 0x0000, 0x12, 59 }, 205 { 0x0000, 0x13, 60 }, { 0x0000, 0x14, 62 }, { 0x0000, 0x15, 63 }, 206 { 0x0000, 0x16, 64 }, { 0x0000, 0x17, 66 }, { 0x0000, 0x18, 67 }, 207 { 0x0000, 0x19, 69 }, { 0x0000, 0x1A, 70 }, { 0x0000, 0x1B, 72 }, 208 { 0x0000, 0x1C, 73 }, { 0x0000, 0x1D, 75 }, { 0x0000, 0x1e, 77 }, 209 { 0x0000, 0x1f, 78 }, { 0x0000, 0x20, 80 }, { 0x0400, 0x21, 82 }, 210 { 0x0800, 0x22, 84 }, { 0x0c00, 0x23, 85 }, { 0x1000, 0x24, 87 }, 211 { 0x1400, 0x25, 89 }, { 0x1800, 0x26, 91 }, { 0x1c00, 0x27, 93 }, 212 { 0x2000, 0x28, 95 }, { 0x2400, 0x29, 97 }, { 0x2800, 0x2a, 99 }, 213 { 0x2c00, 0x2b, 102 }, { 0x3000, 0x2c, 104 }, { 0x3400, 0x2d, 106 }, 214 { 0x3800, 0x2e, 108 }, { 0x3c00, 0x2f, 111 }, { 0x4000, 0x30, 113 }, 215 { 0x4400, 0x31, 116 }, { 0x4800, 0x32, 118 }, { 0x4c00, 0x33, 121 }, 216 { 0x5000, 0x34, 123 }, { 0x5400, 0x35, 126 }, { 0x5800, 0x36, 129 }, 217 { 0x5c00, 0x37, 132 }, { 0x6000, 0x38, 135 }, { 0x6400, 0x39, 137 }, 218 { 0x6800, 0x3a, 141 }, { 0x6c00, 0x3b, 144 }, { 0x7000, 0x3c, 147 }, 219 { 0x7400, 0x3d, 150 }, { 0x7800, 0x3e, 153 }, { 0x7c00, 0x3f, 157 }, 220 { 0x8000, 0x40, 160 }, { 0x8400, 0x41, 164 }, { 0x8800, 0x42, 167 }, 221 { 0x8c00, 0x43, 171 }, { 0x9000, 0x44, 174 }, { 0x9400, 0x45, 178 }, 222 { 0x9800, 0x46, 182 }, { 0x9c00, 0x47, 186 }, { 0xa000, 0x48, 190 }, 223 { 0xa400, 0x49, 194 }, { 0xa800, 0x4a, 199 }, { 0xac00, 0x4b, 203 }, 224 { 0xb000, 0x4c, 207 }, { 0xb400, 0x4d, 212 }, { 0xb800, 0x4e, 217 }, 225 { 0xbc00, 0x4f, 221 }, { 0xc000, 0x50, 226 }, { 0xc400, 0x51, 231 }, 226 { 0xc800, 0x52, 236 }, { 0xcc00, 0x53, 241 }, { 0xd000, 0x54, 247 }, 227 { 0xd400, 0x55, 252 }, { 0xd800, 0x56, 258 }, { 0xdc00, 0x57, 263 }, 228 { 0xe000, 0x58, 269 }, { 0xe400, 0x59, 275 }, { 0xe800, 0x5a, 281 }, 229 { 0xec00, 0x5b, 287 }, { 0xf000, 0x5c, 293 }, { 0xf400, 0x5d, 300 }, 230 { 0xf800, 0x5e, 306 }, { 0xfc00, 0x5f, 313 }, { 0x0001, 0x60, 320 }, 231 { 0x0401, 0x61, 327 }, { 0x0801, 0x62, 334 }, { 0x0c01, 0x63, 341 }, 232 { 0x1001, 0x64, 349 }, { 0x1401, 0x65, 357 }, { 0x1801, 0x66, 364 }, 233 { 0x1c01, 0x67, 372 }, { 0x2001, 0x68, 381 }, { 0x2401, 0x69, 389 }, 234 { 0x2801, 0x6a, 397 }, { 0x2c01, 0x6b, 406 }, { 0x3001, 0x6c, 415 }, 235 { 0x3401, 0x6d, 424 }, { 0x3801, 0x6e, 433 }, { 0x3c01, 0x6f, 443 }, 236 { 0x4001, 0x70, 453 }, { 0x4401, 0x71, 462 }, { 0x4801, 0x72, 473 }, 237 { 0x4c01, 0x73, 483 }, { 0x5001, 0x74, 494 }, { 0x5401, 0x75, 504 }, 238 { 0x5801, 0x76, 515 }, { 0x5c01, 0x77, 527 }, { 0x6001, 0x78, 538 }, 239 { 0x6401, 0x79, 550 }, { 0x6801, 0x7a, 562 }, { 0x6c01, 0x7b, 574 }, 240 { 0x7001, 0x7c, 587 }, { 0x7401, 0x7d, 600 }, { 0x7801, 0x7e, 613 }, 241 { 0x7c01, 0x7f, 626 }, { 0x8001, 0x00, 640 }, { 0x8401, 0x00, 654 }, 242 { 0x8801, 0x00, 668 }, { 0x8c01, 0x00, 683 }, { 0x9001, 0x00, 698 }, 243 { 0x9401, 0x00, 713 }, { 0x9801, 0x00, 729 }, { 0x9c01, 0x00, 745 }, 244 { 0xa001, 0x00, 761 }, { 0xa401, 0x00, 778 }, { 0xa801, 0x00, 795 }, 245 { 0xac01, 0x00, 812 }, { 0xb001, 0x00, 830 }, { 0xb401, 0x00, 848 }, 246 { 0xb801, 0x00, 867 }, { 0xbc01, 0x00, 886 }, { 0xc001, 0x00, 905 }, 247 { 0xc401, 0x00, 925 }, { 0xc801, 0x00, 945 }, { 0xcc01, 0x00, 966 }, 248 { 0xd001, 0x00, 987 }, { 0xd401, 0x00, 1009 }, { 0xd801, 0x00, 1031 }, 249 { 0xdc01, 0x00, 1053 }, { 0xe001, 0x00, 1076 }, { 0xe401, 0x00, 1100 }, 250 { 0xe801, 0x00, 1124 }, { 0xec01, 0x00, 1149 }, { 0xf001, 0x00, 1174 }, 251 { 0xf401, 0x00, 1199 }, { 0xf801, 0x00, 1226 }, { 0xfc01, 0x00, 1253 } 252 }; 253 254 #define joycon_max_rumble_amp (1003) 255 static const struct joycon_rumble_amp_data joycon_rumble_amplitudes[] = { 256 /* high, low, amp */ 257 { 0x00, 0x0040, 0 }, 258 { 0x02, 0x8040, 10 }, { 0x04, 0x0041, 12 }, { 0x06, 0x8041, 14 }, 259 { 0x08, 0x0042, 17 }, { 0x0a, 0x8042, 20 }, { 0x0c, 0x0043, 24 }, 260 { 0x0e, 0x8043, 28 }, { 0x10, 0x0044, 33 }, { 0x12, 0x8044, 40 }, 261 { 0x14, 0x0045, 47 }, { 0x16, 0x8045, 56 }, { 0x18, 0x0046, 67 }, 262 { 0x1a, 0x8046, 80 }, { 0x1c, 0x0047, 95 }, { 0x1e, 0x8047, 112 }, 263 { 0x20, 0x0048, 117 }, { 0x22, 0x8048, 123 }, { 0x24, 0x0049, 128 }, 264 { 0x26, 0x8049, 134 }, { 0x28, 0x004a, 140 }, { 0x2a, 0x804a, 146 }, 265 { 0x2c, 0x004b, 152 }, { 0x2e, 0x804b, 159 }, { 0x30, 0x004c, 166 }, 266 { 0x32, 0x804c, 173 }, { 0x34, 0x004d, 181 }, { 0x36, 0x804d, 189 }, 267 { 0x38, 0x004e, 198 }, { 0x3a, 0x804e, 206 }, { 0x3c, 0x004f, 215 }, 268 { 0x3e, 0x804f, 225 }, { 0x40, 0x0050, 230 }, { 0x42, 0x8050, 235 }, 269 { 0x44, 0x0051, 240 }, { 0x46, 0x8051, 245 }, { 0x48, 0x0052, 251 }, 270 { 0x4a, 0x8052, 256 }, { 0x4c, 0x0053, 262 }, { 0x4e, 0x8053, 268 }, 271 { 0x50, 0x0054, 273 }, { 0x52, 0x8054, 279 }, { 0x54, 0x0055, 286 }, 272 { 0x56, 0x8055, 292 }, { 0x58, 0x0056, 298 }, { 0x5a, 0x8056, 305 }, 273 { 0x5c, 0x0057, 311 }, { 0x5e, 0x8057, 318 }, { 0x60, 0x0058, 325 }, 274 { 0x62, 0x8058, 332 }, { 0x64, 0x0059, 340 }, { 0x66, 0x8059, 347 }, 275 { 0x68, 0x005a, 355 }, { 0x6a, 0x805a, 362 }, { 0x6c, 0x005b, 370 }, 276 { 0x6e, 0x805b, 378 }, { 0x70, 0x005c, 387 }, { 0x72, 0x805c, 395 }, 277 { 0x74, 0x005d, 404 }, { 0x76, 0x805d, 413 }, { 0x78, 0x005e, 422 }, 278 { 0x7a, 0x805e, 431 }, { 0x7c, 0x005f, 440 }, { 0x7e, 0x805f, 450 }, 279 { 0x80, 0x0060, 460 }, { 0x82, 0x8060, 470 }, { 0x84, 0x0061, 480 }, 280 { 0x86, 0x8061, 491 }, { 0x88, 0x0062, 501 }, { 0x8a, 0x8062, 512 }, 281 { 0x8c, 0x0063, 524 }, { 0x8e, 0x8063, 535 }, { 0x90, 0x0064, 547 }, 282 { 0x92, 0x8064, 559 }, { 0x94, 0x0065, 571 }, { 0x96, 0x8065, 584 }, 283 { 0x98, 0x0066, 596 }, { 0x9a, 0x8066, 609 }, { 0x9c, 0x0067, 623 }, 284 { 0x9e, 0x8067, 636 }, { 0xa0, 0x0068, 650 }, { 0xa2, 0x8068, 665 }, 285 { 0xa4, 0x0069, 679 }, { 0xa6, 0x8069, 694 }, { 0xa8, 0x006a, 709 }, 286 { 0xaa, 0x806a, 725 }, { 0xac, 0x006b, 741 }, { 0xae, 0x806b, 757 }, 287 { 0xb0, 0x006c, 773 }, { 0xb2, 0x806c, 790 }, { 0xb4, 0x006d, 808 }, 288 { 0xb6, 0x806d, 825 }, { 0xb8, 0x006e, 843 }, { 0xba, 0x806e, 862 }, 289 { 0xbc, 0x006f, 881 }, { 0xbe, 0x806f, 900 }, { 0xc0, 0x0070, 920 }, 290 { 0xc2, 0x8070, 940 }, { 0xc4, 0x0071, 960 }, { 0xc6, 0x8071, 981 }, 291 { 0xc8, 0x0072, joycon_max_rumble_amp } 292 }; 293 static const u16 JC_RUMBLE_DFLT_LOW_FREQ = 160; 294 static const u16 JC_RUMBLE_DFLT_HIGH_FREQ = 320; 295 static const unsigned short JC_RUMBLE_ZERO_AMP_PKT_CNT = 5; 296 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 297 static const u16 JC_RUMBLE_PERIOD_MS = 50; 298 299 /* States for controller state machine */ 300 enum joycon_ctlr_state { 301 JOYCON_CTLR_STATE_INIT, 302 JOYCON_CTLR_STATE_READ, 303 JOYCON_CTLR_STATE_REMOVED, 304 }; 305 306 /* Controller type received as part of device info */ 307 enum joycon_ctlr_type { 308 JOYCON_CTLR_TYPE_JCL = 0x01, 309 JOYCON_CTLR_TYPE_JCR = 0x02, 310 JOYCON_CTLR_TYPE_PRO = 0x03, 311 }; 312 313 struct joycon_stick_cal { 314 s32 max; 315 s32 min; 316 s32 center; 317 }; 318 319 struct joycon_imu_cal { 320 s16 offset[3]; 321 s16 scale[3]; 322 }; 323 324 /* 325 * All the controller's button values are stored in a u32. 326 * They can be accessed with bitwise ANDs. 327 */ 328 #define JC_BTN_Y BIT(0) 329 #define JC_BTN_X BIT(1) 330 #define JC_BTN_B BIT(2) 331 #define JC_BTN_A BIT(3) 332 #define JC_BTN_SR_R BIT(4) 333 #define JC_BTN_SL_R BIT(5) 334 #define JC_BTN_R BIT(6) 335 #define JC_BTN_ZR BIT(7) 336 #define JC_BTN_MINUS BIT(8) 337 #define JC_BTN_PLUS BIT(9) 338 #define JC_BTN_RSTICK BIT(10) 339 #define JC_BTN_LSTICK BIT(11) 340 #define JC_BTN_HOME BIT(12) 341 #define JC_BTN_CAP BIT(13) /* capture button */ 342 #define JC_BTN_DOWN BIT(16) 343 #define JC_BTN_UP BIT(17) 344 #define JC_BTN_RIGHT BIT(18) 345 #define JC_BTN_LEFT BIT(19) 346 #define JC_BTN_SR_L BIT(20) 347 #define JC_BTN_SL_L BIT(21) 348 #define JC_BTN_L BIT(22) 349 #define JC_BTN_ZL BIT(23) 350 351 enum joycon_msg_type { 352 JOYCON_MSG_TYPE_NONE, 353 JOYCON_MSG_TYPE_USB, 354 JOYCON_MSG_TYPE_SUBCMD, 355 }; 356 357 struct joycon_rumble_output { 358 u8 output_id; 359 u8 packet_num; 360 u8 rumble_data[8]; 361 } __packed; 362 363 struct joycon_subcmd_request { 364 u8 output_id; /* must be 0x01 for subcommand, 0x10 for rumble only */ 365 u8 packet_num; /* incremented every send */ 366 u8 rumble_data[8]; 367 u8 subcmd_id; 368 u8 data[]; /* length depends on the subcommand */ 369 } __packed; 370 371 struct joycon_subcmd_reply { 372 u8 ack; /* MSB 1 for ACK, 0 for NACK */ 373 u8 id; /* id of requested subcmd */ 374 u8 data[]; /* will be at most 35 bytes */ 375 } __packed; 376 377 struct joycon_imu_data { 378 s16 accel_x; 379 s16 accel_y; 380 s16 accel_z; 381 s16 gyro_x; 382 s16 gyro_y; 383 s16 gyro_z; 384 } __packed; 385 386 struct joycon_input_report { 387 u8 id; 388 u8 timer; 389 u8 bat_con; /* battery and connection info */ 390 u8 button_status[3]; 391 u8 left_stick[3]; 392 u8 right_stick[3]; 393 u8 vibrator_report; 394 395 union { 396 struct joycon_subcmd_reply subcmd_reply; 397 /* IMU input reports contain 3 samples */ 398 u8 imu_raw_bytes[sizeof(struct joycon_imu_data) * 3]; 399 }; 400 } __packed; 401 402 #define JC_MAX_RESP_SIZE (sizeof(struct joycon_input_report) + 35) 403 #define JC_RUMBLE_DATA_SIZE 8 404 #define JC_RUMBLE_QUEUE_SIZE 8 405 406 static const char * const joycon_player_led_names[] = { 407 LED_FUNCTION_PLAYER1, 408 LED_FUNCTION_PLAYER2, 409 LED_FUNCTION_PLAYER3, 410 LED_FUNCTION_PLAYER4, 411 }; 412 #define JC_NUM_LEDS ARRAY_SIZE(joycon_player_led_names) 413 414 /* Each physical controller is associated with a joycon_ctlr struct */ 415 struct joycon_ctlr { 416 struct hid_device *hdev; 417 struct input_dev *input; 418 struct led_classdev leds[JC_NUM_LEDS]; /* player leds */ 419 struct led_classdev home_led; 420 enum joycon_ctlr_state ctlr_state; 421 spinlock_t lock; 422 u8 mac_addr[6]; 423 char *mac_addr_str; 424 enum joycon_ctlr_type ctlr_type; 425 426 /* The following members are used for synchronous sends/receives */ 427 enum joycon_msg_type msg_type; 428 u8 subcmd_num; 429 struct mutex output_mutex; 430 u8 input_buf[JC_MAX_RESP_SIZE]; 431 wait_queue_head_t wait; 432 bool received_resp; 433 u8 usb_ack_match; 434 u8 subcmd_ack_match; 435 bool received_input_report; 436 unsigned int last_input_report_msecs; 437 unsigned int last_subcmd_sent_msecs; 438 unsigned int consecutive_valid_report_deltas; 439 440 /* factory calibration data */ 441 struct joycon_stick_cal left_stick_cal_x; 442 struct joycon_stick_cal left_stick_cal_y; 443 struct joycon_stick_cal right_stick_cal_x; 444 struct joycon_stick_cal right_stick_cal_y; 445 446 struct joycon_imu_cal accel_cal; 447 struct joycon_imu_cal gyro_cal; 448 449 /* prevents needlessly recalculating these divisors every sample */ 450 s32 imu_cal_accel_divisor[3]; 451 s32 imu_cal_gyro_divisor[3]; 452 453 /* power supply data */ 454 struct power_supply *battery; 455 struct power_supply_desc battery_desc; 456 u8 battery_capacity; 457 bool battery_charging; 458 bool host_powered; 459 460 /* rumble */ 461 u8 rumble_data[JC_RUMBLE_QUEUE_SIZE][JC_RUMBLE_DATA_SIZE]; 462 int rumble_queue_head; 463 int rumble_queue_tail; 464 struct workqueue_struct *rumble_queue; 465 struct work_struct rumble_worker; 466 unsigned int rumble_msecs; 467 u16 rumble_ll_freq; 468 u16 rumble_lh_freq; 469 u16 rumble_rl_freq; 470 u16 rumble_rh_freq; 471 unsigned short rumble_zero_countdown; 472 473 /* imu */ 474 struct input_dev *imu_input; 475 bool imu_first_packet_received; /* helps in initiating timestamp */ 476 unsigned int imu_timestamp_us; /* timestamp we report to userspace */ 477 unsigned int imu_last_pkt_ms; /* used to calc imu report delta */ 478 /* the following are used to track the average imu report time delta */ 479 unsigned int imu_delta_samples_count; 480 unsigned int imu_delta_samples_sum; 481 unsigned int imu_avg_delta_ms; 482 }; 483 484 /* Helper macros for checking controller type */ 485 #define jc_type_is_joycon(ctlr) \ 486 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL || \ 487 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR || \ 488 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 489 #define jc_type_is_procon(ctlr) \ 490 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_PROCON) 491 #define jc_type_is_chrggrip(ctlr) \ 492 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 493 494 /* Does this controller have inputs associated with left joycon? */ 495 #define jc_type_has_left(ctlr) \ 496 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL || \ 497 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 498 499 /* Does this controller have inputs associated with right joycon? */ 500 #define jc_type_has_right(ctlr) \ 501 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR || \ 502 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 503 504 static int __joycon_hid_send(struct hid_device *hdev, u8 *data, size_t len) 505 { 506 u8 *buf; 507 int ret; 508 509 buf = kmemdup(data, len, GFP_KERNEL); 510 if (!buf) 511 return -ENOMEM; 512 ret = hid_hw_output_report(hdev, buf, len); 513 kfree(buf); 514 if (ret < 0) 515 hid_dbg(hdev, "Failed to send output report ret=%d\n", ret); 516 return ret; 517 } 518 519 static void joycon_wait_for_input_report(struct joycon_ctlr *ctlr) 520 { 521 int ret; 522 523 /* 524 * If we are in the proper reporting mode, wait for an input 525 * report prior to sending the subcommand. This improves 526 * reliability considerably. 527 */ 528 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) { 529 unsigned long flags; 530 531 spin_lock_irqsave(&ctlr->lock, flags); 532 ctlr->received_input_report = false; 533 spin_unlock_irqrestore(&ctlr->lock, flags); 534 ret = wait_event_timeout(ctlr->wait, 535 ctlr->received_input_report, 536 HZ / 4); 537 /* We will still proceed, even with a timeout here */ 538 if (!ret) 539 hid_warn(ctlr->hdev, 540 "timeout waiting for input report\n"); 541 } 542 } 543 544 /* 545 * Sending subcommands and/or rumble data at too high a rate can cause bluetooth 546 * controller disconnections. 547 */ 548 #define JC_INPUT_REPORT_MIN_DELTA 8 549 #define JC_INPUT_REPORT_MAX_DELTA 17 550 #define JC_SUBCMD_TX_OFFSET_MS 4 551 #define JC_SUBCMD_VALID_DELTA_REQ 3 552 #define JC_SUBCMD_RATE_MAX_ATTEMPTS 500 553 #define JC_SUBCMD_RATE_LIMITER_USB_MS 20 554 #define JC_SUBCMD_RATE_LIMITER_BT_MS 60 555 #define JC_SUBCMD_RATE_LIMITER_MS(ctlr) ((ctlr)->hdev->bus == BUS_USB ? JC_SUBCMD_RATE_LIMITER_USB_MS : JC_SUBCMD_RATE_LIMITER_BT_MS) 556 static void joycon_enforce_subcmd_rate(struct joycon_ctlr *ctlr) 557 { 558 unsigned int current_ms; 559 unsigned long subcmd_delta; 560 int consecutive_valid_deltas = 0; 561 int attempts = 0; 562 unsigned long flags; 563 564 if (unlikely(ctlr->ctlr_state != JOYCON_CTLR_STATE_READ)) 565 return; 566 567 do { 568 joycon_wait_for_input_report(ctlr); 569 current_ms = jiffies_to_msecs(jiffies); 570 subcmd_delta = current_ms - ctlr->last_subcmd_sent_msecs; 571 572 spin_lock_irqsave(&ctlr->lock, flags); 573 consecutive_valid_deltas = ctlr->consecutive_valid_report_deltas; 574 spin_unlock_irqrestore(&ctlr->lock, flags); 575 576 attempts++; 577 } while ((consecutive_valid_deltas < JC_SUBCMD_VALID_DELTA_REQ || 578 subcmd_delta < JC_SUBCMD_RATE_LIMITER_MS(ctlr)) && 579 ctlr->ctlr_state == JOYCON_CTLR_STATE_READ && 580 attempts < JC_SUBCMD_RATE_MAX_ATTEMPTS); 581 582 if (attempts >= JC_SUBCMD_RATE_MAX_ATTEMPTS) { 583 hid_warn(ctlr->hdev, "%s: exceeded max attempts", __func__); 584 return; 585 } 586 587 ctlr->last_subcmd_sent_msecs = current_ms; 588 589 /* 590 * Wait a short time after receiving an input report before 591 * transmitting. This should reduce odds of a TX coinciding with an RX. 592 * Minimizing concurrent BT traffic with the controller seems to lower 593 * the rate of disconnections. 594 */ 595 msleep(JC_SUBCMD_TX_OFFSET_MS); 596 } 597 598 static int joycon_hid_send_sync(struct joycon_ctlr *ctlr, u8 *data, size_t len, 599 u32 timeout) 600 { 601 int ret; 602 int tries = 2; 603 604 /* 605 * The controller occasionally seems to drop subcommands. In testing, 606 * doing one retry after a timeout appears to always work. 607 */ 608 while (tries--) { 609 joycon_enforce_subcmd_rate(ctlr); 610 611 ret = __joycon_hid_send(ctlr->hdev, data, len); 612 if (ret < 0) { 613 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 614 return ret; 615 } 616 617 ret = wait_event_timeout(ctlr->wait, ctlr->received_resp, 618 timeout); 619 if (!ret) { 620 hid_dbg(ctlr->hdev, 621 "synchronous send/receive timed out\n"); 622 if (tries) { 623 hid_dbg(ctlr->hdev, 624 "retrying sync send after timeout\n"); 625 } 626 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 627 ret = -ETIMEDOUT; 628 } else { 629 ret = 0; 630 break; 631 } 632 } 633 634 ctlr->received_resp = false; 635 return ret; 636 } 637 638 static int joycon_send_usb(struct joycon_ctlr *ctlr, u8 cmd, u32 timeout) 639 { 640 int ret; 641 u8 buf[2] = {JC_OUTPUT_USB_CMD}; 642 643 buf[1] = cmd; 644 ctlr->usb_ack_match = cmd; 645 ctlr->msg_type = JOYCON_MSG_TYPE_USB; 646 ret = joycon_hid_send_sync(ctlr, buf, sizeof(buf), timeout); 647 if (ret) 648 hid_dbg(ctlr->hdev, "send usb command failed; ret=%d\n", ret); 649 return ret; 650 } 651 652 static int joycon_send_subcmd(struct joycon_ctlr *ctlr, 653 struct joycon_subcmd_request *subcmd, 654 size_t data_len, u32 timeout) 655 { 656 int ret; 657 unsigned long flags; 658 659 spin_lock_irqsave(&ctlr->lock, flags); 660 /* 661 * If the controller has been removed, just return ENODEV so the LED 662 * subsystem doesn't print invalid errors on removal. 663 */ 664 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 665 spin_unlock_irqrestore(&ctlr->lock, flags); 666 return -ENODEV; 667 } 668 memcpy(subcmd->rumble_data, ctlr->rumble_data[ctlr->rumble_queue_tail], 669 JC_RUMBLE_DATA_SIZE); 670 spin_unlock_irqrestore(&ctlr->lock, flags); 671 672 subcmd->output_id = JC_OUTPUT_RUMBLE_AND_SUBCMD; 673 subcmd->packet_num = ctlr->subcmd_num; 674 if (++ctlr->subcmd_num > 0xF) 675 ctlr->subcmd_num = 0; 676 ctlr->subcmd_ack_match = subcmd->subcmd_id; 677 ctlr->msg_type = JOYCON_MSG_TYPE_SUBCMD; 678 679 ret = joycon_hid_send_sync(ctlr, (u8 *)subcmd, 680 sizeof(*subcmd) + data_len, timeout); 681 if (ret < 0) 682 hid_dbg(ctlr->hdev, "send subcommand failed; ret=%d\n", ret); 683 else 684 ret = 0; 685 return ret; 686 } 687 688 /* Supply nibbles for flash and on. Ones correspond to active */ 689 static int joycon_set_player_leds(struct joycon_ctlr *ctlr, u8 flash, u8 on) 690 { 691 struct joycon_subcmd_request *req; 692 u8 buffer[sizeof(*req) + 1] = { 0 }; 693 694 req = (struct joycon_subcmd_request *)buffer; 695 req->subcmd_id = JC_SUBCMD_SET_PLAYER_LIGHTS; 696 req->data[0] = (flash << 4) | on; 697 698 hid_dbg(ctlr->hdev, "setting player leds\n"); 699 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 700 } 701 702 static int joycon_request_spi_flash_read(struct joycon_ctlr *ctlr, 703 u32 start_addr, u8 size, u8 **reply) 704 { 705 struct joycon_subcmd_request *req; 706 struct joycon_input_report *report; 707 u8 buffer[sizeof(*req) + 5] = { 0 }; 708 u8 *data; 709 int ret; 710 711 if (!reply) 712 return -EINVAL; 713 714 req = (struct joycon_subcmd_request *)buffer; 715 req->subcmd_id = JC_SUBCMD_SPI_FLASH_READ; 716 data = req->data; 717 put_unaligned_le32(start_addr, data); 718 data[4] = size; 719 720 hid_dbg(ctlr->hdev, "requesting SPI flash data\n"); 721 ret = joycon_send_subcmd(ctlr, req, 5, HZ); 722 if (ret) { 723 hid_err(ctlr->hdev, "failed reading SPI flash; ret=%d\n", ret); 724 } else { 725 report = (struct joycon_input_report *)ctlr->input_buf; 726 /* The read data starts at the 6th byte */ 727 *reply = &report->subcmd_reply.data[5]; 728 } 729 return ret; 730 } 731 732 /* 733 * User calibration's presence is denoted with a magic byte preceding it. 734 * returns 0 if magic val is present, 1 if not present, < 0 on error 735 */ 736 static int joycon_check_for_cal_magic(struct joycon_ctlr *ctlr, u32 flash_addr) 737 { 738 int ret; 739 u8 *reply; 740 741 ret = joycon_request_spi_flash_read(ctlr, flash_addr, 742 JC_CAL_USR_MAGIC_SIZE, &reply); 743 if (ret) 744 return ret; 745 746 return reply[0] != JC_CAL_USR_MAGIC_0 || reply[1] != JC_CAL_USR_MAGIC_1; 747 } 748 749 static int joycon_read_stick_calibration(struct joycon_ctlr *ctlr, u16 cal_addr, 750 struct joycon_stick_cal *cal_x, 751 struct joycon_stick_cal *cal_y, 752 bool left_stick) 753 { 754 s32 x_max_above; 755 s32 x_min_below; 756 s32 y_max_above; 757 s32 y_min_below; 758 u8 *raw_cal; 759 int ret; 760 761 ret = joycon_request_spi_flash_read(ctlr, cal_addr, 762 JC_CAL_STICK_DATA_SIZE, &raw_cal); 763 if (ret) 764 return ret; 765 766 /* stick calibration parsing: note the order differs based on stick */ 767 if (left_stick) { 768 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 769 12); 770 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 771 12); 772 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 773 12); 774 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 775 12); 776 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 777 12); 778 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 779 12); 780 } else { 781 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 782 12); 783 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 784 12); 785 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 786 12); 787 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 788 12); 789 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 790 12); 791 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 792 12); 793 } 794 795 cal_x->max = cal_x->center + x_max_above; 796 cal_x->min = cal_x->center - x_min_below; 797 cal_y->max = cal_y->center + y_max_above; 798 cal_y->min = cal_y->center - y_min_below; 799 800 /* check if calibration values are plausible */ 801 if (cal_x->min >= cal_x->center || cal_x->center >= cal_x->max || 802 cal_y->min >= cal_y->center || cal_y->center >= cal_y->max) 803 ret = -EINVAL; 804 805 return ret; 806 } 807 808 static const u16 DFLT_STICK_CAL_CEN = 2000; 809 static const u16 DFLT_STICK_CAL_MAX = 3500; 810 static const u16 DFLT_STICK_CAL_MIN = 500; 811 static void joycon_use_default_calibration(struct hid_device *hdev, 812 struct joycon_stick_cal *cal_x, 813 struct joycon_stick_cal *cal_y, 814 const char *stick, int ret) 815 { 816 hid_warn(hdev, 817 "Failed to read %s stick cal, using defaults; e=%d\n", 818 stick, ret); 819 820 cal_x->center = cal_y->center = DFLT_STICK_CAL_CEN; 821 cal_x->max = cal_y->max = DFLT_STICK_CAL_MAX; 822 cal_x->min = cal_y->min = DFLT_STICK_CAL_MIN; 823 } 824 825 static int joycon_request_calibration(struct joycon_ctlr *ctlr) 826 { 827 u16 left_stick_addr = JC_CAL_FCT_DATA_LEFT_ADDR; 828 u16 right_stick_addr = JC_CAL_FCT_DATA_RIGHT_ADDR; 829 int ret; 830 831 hid_dbg(ctlr->hdev, "requesting cal data\n"); 832 833 /* check if user stick calibrations are present */ 834 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_LEFT_MAGIC_ADDR)) { 835 left_stick_addr = JC_CAL_USR_LEFT_DATA_ADDR; 836 hid_info(ctlr->hdev, "using user cal for left stick\n"); 837 } else { 838 hid_info(ctlr->hdev, "using factory cal for left stick\n"); 839 } 840 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_RIGHT_MAGIC_ADDR)) { 841 right_stick_addr = JC_CAL_USR_RIGHT_DATA_ADDR; 842 hid_info(ctlr->hdev, "using user cal for right stick\n"); 843 } else { 844 hid_info(ctlr->hdev, "using factory cal for right stick\n"); 845 } 846 847 /* read the left stick calibration data */ 848 ret = joycon_read_stick_calibration(ctlr, left_stick_addr, 849 &ctlr->left_stick_cal_x, 850 &ctlr->left_stick_cal_y, 851 true); 852 853 if (ret) 854 joycon_use_default_calibration(ctlr->hdev, 855 &ctlr->left_stick_cal_x, 856 &ctlr->left_stick_cal_y, 857 "left", ret); 858 859 /* read the right stick calibration data */ 860 ret = joycon_read_stick_calibration(ctlr, right_stick_addr, 861 &ctlr->right_stick_cal_x, 862 &ctlr->right_stick_cal_y, 863 false); 864 865 if (ret) 866 joycon_use_default_calibration(ctlr->hdev, 867 &ctlr->right_stick_cal_x, 868 &ctlr->right_stick_cal_y, 869 "right", ret); 870 871 hid_dbg(ctlr->hdev, "calibration:\n" 872 "l_x_c=%d l_x_max=%d l_x_min=%d\n" 873 "l_y_c=%d l_y_max=%d l_y_min=%d\n" 874 "r_x_c=%d r_x_max=%d r_x_min=%d\n" 875 "r_y_c=%d r_y_max=%d r_y_min=%d\n", 876 ctlr->left_stick_cal_x.center, 877 ctlr->left_stick_cal_x.max, 878 ctlr->left_stick_cal_x.min, 879 ctlr->left_stick_cal_y.center, 880 ctlr->left_stick_cal_y.max, 881 ctlr->left_stick_cal_y.min, 882 ctlr->right_stick_cal_x.center, 883 ctlr->right_stick_cal_x.max, 884 ctlr->right_stick_cal_x.min, 885 ctlr->right_stick_cal_y.center, 886 ctlr->right_stick_cal_y.max, 887 ctlr->right_stick_cal_y.min); 888 889 return 0; 890 } 891 892 /* 893 * These divisors are calculated once rather than for each sample. They are only 894 * dependent on the IMU calibration values. They are used when processing the 895 * IMU input reports. 896 */ 897 static void joycon_calc_imu_cal_divisors(struct joycon_ctlr *ctlr) 898 { 899 int i, divz = 0; 900 901 for (i = 0; i < 3; i++) { 902 ctlr->imu_cal_accel_divisor[i] = ctlr->accel_cal.scale[i] - 903 ctlr->accel_cal.offset[i]; 904 ctlr->imu_cal_gyro_divisor[i] = ctlr->gyro_cal.scale[i] - 905 ctlr->gyro_cal.offset[i]; 906 907 if (ctlr->imu_cal_accel_divisor[i] == 0) { 908 ctlr->imu_cal_accel_divisor[i] = 1; 909 divz++; 910 } 911 912 if (ctlr->imu_cal_gyro_divisor[i] == 0) { 913 ctlr->imu_cal_gyro_divisor[i] = 1; 914 divz++; 915 } 916 } 917 918 if (divz) 919 hid_warn(ctlr->hdev, "inaccurate IMU divisors (%d)\n", divz); 920 } 921 922 static const s16 DFLT_ACCEL_OFFSET /*= 0*/; 923 static const s16 DFLT_ACCEL_SCALE = 16384; 924 static const s16 DFLT_GYRO_OFFSET /*= 0*/; 925 static const s16 DFLT_GYRO_SCALE = 13371; 926 static int joycon_request_imu_calibration(struct joycon_ctlr *ctlr) 927 { 928 u16 imu_cal_addr = JC_IMU_CAL_FCT_DATA_ADDR; 929 u8 *raw_cal; 930 int ret; 931 int i; 932 933 /* check if user calibration exists */ 934 if (!joycon_check_for_cal_magic(ctlr, JC_IMU_CAL_USR_MAGIC_ADDR)) { 935 imu_cal_addr = JC_IMU_CAL_USR_DATA_ADDR; 936 hid_info(ctlr->hdev, "using user cal for IMU\n"); 937 } else { 938 hid_info(ctlr->hdev, "using factory cal for IMU\n"); 939 } 940 941 /* request IMU calibration data */ 942 hid_dbg(ctlr->hdev, "requesting IMU cal data\n"); 943 ret = joycon_request_spi_flash_read(ctlr, imu_cal_addr, 944 JC_IMU_CAL_DATA_SIZE, &raw_cal); 945 if (ret) { 946 hid_warn(ctlr->hdev, 947 "Failed to read IMU cal, using defaults; ret=%d\n", 948 ret); 949 950 for (i = 0; i < 3; i++) { 951 ctlr->accel_cal.offset[i] = DFLT_ACCEL_OFFSET; 952 ctlr->accel_cal.scale[i] = DFLT_ACCEL_SCALE; 953 ctlr->gyro_cal.offset[i] = DFLT_GYRO_OFFSET; 954 ctlr->gyro_cal.scale[i] = DFLT_GYRO_SCALE; 955 } 956 joycon_calc_imu_cal_divisors(ctlr); 957 return ret; 958 } 959 960 /* IMU calibration parsing */ 961 for (i = 0; i < 3; i++) { 962 int j = i * 2; 963 964 ctlr->accel_cal.offset[i] = get_unaligned_le16(raw_cal + j); 965 ctlr->accel_cal.scale[i] = get_unaligned_le16(raw_cal + j + 6); 966 ctlr->gyro_cal.offset[i] = get_unaligned_le16(raw_cal + j + 12); 967 ctlr->gyro_cal.scale[i] = get_unaligned_le16(raw_cal + j + 18); 968 } 969 970 joycon_calc_imu_cal_divisors(ctlr); 971 972 hid_dbg(ctlr->hdev, "IMU calibration:\n" 973 "a_o[0]=%d a_o[1]=%d a_o[2]=%d\n" 974 "a_s[0]=%d a_s[1]=%d a_s[2]=%d\n" 975 "g_o[0]=%d g_o[1]=%d g_o[2]=%d\n" 976 "g_s[0]=%d g_s[1]=%d g_s[2]=%d\n", 977 ctlr->accel_cal.offset[0], 978 ctlr->accel_cal.offset[1], 979 ctlr->accel_cal.offset[2], 980 ctlr->accel_cal.scale[0], 981 ctlr->accel_cal.scale[1], 982 ctlr->accel_cal.scale[2], 983 ctlr->gyro_cal.offset[0], 984 ctlr->gyro_cal.offset[1], 985 ctlr->gyro_cal.offset[2], 986 ctlr->gyro_cal.scale[0], 987 ctlr->gyro_cal.scale[1], 988 ctlr->gyro_cal.scale[2]); 989 990 return 0; 991 } 992 993 static int joycon_set_report_mode(struct joycon_ctlr *ctlr) 994 { 995 struct joycon_subcmd_request *req; 996 u8 buffer[sizeof(*req) + 1] = { 0 }; 997 998 req = (struct joycon_subcmd_request *)buffer; 999 req->subcmd_id = JC_SUBCMD_SET_REPORT_MODE; 1000 req->data[0] = 0x30; /* standard, full report mode */ 1001 1002 hid_dbg(ctlr->hdev, "setting controller report mode\n"); 1003 return joycon_send_subcmd(ctlr, req, 1, HZ); 1004 } 1005 1006 static int joycon_enable_rumble(struct joycon_ctlr *ctlr) 1007 { 1008 struct joycon_subcmd_request *req; 1009 u8 buffer[sizeof(*req) + 1] = { 0 }; 1010 1011 req = (struct joycon_subcmd_request *)buffer; 1012 req->subcmd_id = JC_SUBCMD_ENABLE_VIBRATION; 1013 req->data[0] = 0x01; /* note: 0x00 would disable */ 1014 1015 hid_dbg(ctlr->hdev, "enabling rumble\n"); 1016 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 1017 } 1018 1019 static int joycon_enable_imu(struct joycon_ctlr *ctlr) 1020 { 1021 struct joycon_subcmd_request *req; 1022 u8 buffer[sizeof(*req) + 1] = { 0 }; 1023 1024 req = (struct joycon_subcmd_request *)buffer; 1025 req->subcmd_id = JC_SUBCMD_ENABLE_IMU; 1026 req->data[0] = 0x01; /* note: 0x00 would disable */ 1027 1028 hid_dbg(ctlr->hdev, "enabling IMU\n"); 1029 return joycon_send_subcmd(ctlr, req, 1, HZ); 1030 } 1031 1032 static s32 joycon_map_stick_val(struct joycon_stick_cal *cal, s32 val) 1033 { 1034 s32 center = cal->center; 1035 s32 min = cal->min; 1036 s32 max = cal->max; 1037 s32 new_val; 1038 1039 if (val > center) { 1040 new_val = (val - center) * JC_MAX_STICK_MAG; 1041 new_val /= (max - center); 1042 } else { 1043 new_val = (center - val) * -JC_MAX_STICK_MAG; 1044 new_val /= (center - min); 1045 } 1046 new_val = clamp(new_val, (s32)-JC_MAX_STICK_MAG, (s32)JC_MAX_STICK_MAG); 1047 return new_val; 1048 } 1049 1050 static void joycon_input_report_parse_imu_data(struct joycon_ctlr *ctlr, 1051 struct joycon_input_report *rep, 1052 struct joycon_imu_data *imu_data) 1053 { 1054 u8 *raw = rep->imu_raw_bytes; 1055 int i; 1056 1057 for (i = 0; i < 3; i++) { 1058 struct joycon_imu_data *data = &imu_data[i]; 1059 1060 data->accel_x = get_unaligned_le16(raw + 0); 1061 data->accel_y = get_unaligned_le16(raw + 2); 1062 data->accel_z = get_unaligned_le16(raw + 4); 1063 data->gyro_x = get_unaligned_le16(raw + 6); 1064 data->gyro_y = get_unaligned_le16(raw + 8); 1065 data->gyro_z = get_unaligned_le16(raw + 10); 1066 /* point to next imu sample */ 1067 raw += sizeof(struct joycon_imu_data); 1068 } 1069 } 1070 1071 static void joycon_parse_imu_report(struct joycon_ctlr *ctlr, 1072 struct joycon_input_report *rep) 1073 { 1074 struct joycon_imu_data imu_data[3] = {0}; /* 3 reports per packet */ 1075 struct input_dev *idev = ctlr->imu_input; 1076 unsigned int msecs = jiffies_to_msecs(jiffies); 1077 unsigned int last_msecs = ctlr->imu_last_pkt_ms; 1078 int i; 1079 int value[6]; 1080 1081 joycon_input_report_parse_imu_data(ctlr, rep, imu_data); 1082 1083 /* 1084 * There are complexities surrounding how we determine the timestamps we 1085 * associate with the samples we pass to userspace. The IMU input 1086 * reports do not provide us with a good timestamp. There's a quickly 1087 * incrementing 8-bit counter per input report, but it is not very 1088 * useful for this purpose (it is not entirely clear what rate it 1089 * increments at or if it varies based on packet push rate - more on 1090 * the push rate below...). 1091 * 1092 * The reverse engineering work done on the joy-cons and pro controllers 1093 * by the community seems to indicate the following: 1094 * - The controller samples the IMU every 1.35ms. It then does some of 1095 * its own processing, probably averaging the samples out. 1096 * - Each imu input report contains 3 IMU samples, (usually 5ms apart). 1097 * - In the standard reporting mode (which this driver uses exclusively) 1098 * input reports are pushed from the controller as follows: 1099 * * joy-con (bluetooth): every 15 ms 1100 * * joy-cons (in charging grip via USB): every 15 ms 1101 * * pro controller (USB): every 15 ms 1102 * * pro controller (bluetooth): every 8 ms (this is the wildcard) 1103 * 1104 * Further complicating matters is that some bluetooth stacks are known 1105 * to alter the controller's packet rate by hardcoding the bluetooth 1106 * SSR for the switch controllers (android's stack currently sets the 1107 * SSR to 11ms for both the joy-cons and pro controllers). 1108 * 1109 * In my own testing, I've discovered that my pro controller either 1110 * reports IMU sample batches every 11ms or every 15ms. This rate is 1111 * stable after connecting. It isn't 100% clear what determines this 1112 * rate. Importantly, even when sending every 11ms, none of the samples 1113 * are duplicates. This seems to indicate that the time deltas between 1114 * reported samples can vary based on the input report rate. 1115 * 1116 * The solution employed in this driver is to keep track of the average 1117 * time delta between IMU input reports. In testing, this value has 1118 * proven to be stable, staying at 15ms or 11ms, though other hardware 1119 * configurations and bluetooth stacks could potentially see other rates 1120 * (hopefully this will become more clear as more people use the 1121 * driver). 1122 * 1123 * Keeping track of the average report delta allows us to submit our 1124 * timestamps to userspace based on that. Each report contains 3 1125 * samples, so the IMU sampling rate should be avg_time_delta/3. We can 1126 * also use this average to detect events where we have dropped a 1127 * packet. The userspace timestamp for the samples will be adjusted 1128 * accordingly to prevent unwanted behvaior. 1129 */ 1130 if (!ctlr->imu_first_packet_received) { 1131 ctlr->imu_timestamp_us = 0; 1132 ctlr->imu_delta_samples_count = 0; 1133 ctlr->imu_delta_samples_sum = 0; 1134 ctlr->imu_avg_delta_ms = JC_IMU_DFLT_AVG_DELTA_MS; 1135 ctlr->imu_first_packet_received = true; 1136 } else { 1137 unsigned int delta = msecs - last_msecs; 1138 unsigned int dropped_pkts; 1139 unsigned int dropped_threshold; 1140 1141 /* avg imu report delta housekeeping */ 1142 ctlr->imu_delta_samples_sum += delta; 1143 ctlr->imu_delta_samples_count++; 1144 if (ctlr->imu_delta_samples_count >= 1145 JC_IMU_SAMPLES_PER_DELTA_AVG) { 1146 ctlr->imu_avg_delta_ms = ctlr->imu_delta_samples_sum / 1147 ctlr->imu_delta_samples_count; 1148 ctlr->imu_delta_samples_count = 0; 1149 ctlr->imu_delta_samples_sum = 0; 1150 } 1151 1152 /* don't ever want divide by zero shenanigans */ 1153 if (ctlr->imu_avg_delta_ms == 0) { 1154 ctlr->imu_avg_delta_ms = 1; 1155 hid_warn(ctlr->hdev, "calculated avg imu delta of 0\n"); 1156 } 1157 1158 /* useful for debugging IMU sample rate */ 1159 hid_dbg(ctlr->hdev, 1160 "imu_report: ms=%u last_ms=%u delta=%u avg_delta=%u\n", 1161 msecs, last_msecs, delta, ctlr->imu_avg_delta_ms); 1162 1163 /* check if any packets have been dropped */ 1164 dropped_threshold = ctlr->imu_avg_delta_ms * 3 / 2; 1165 dropped_pkts = (delta - min(delta, dropped_threshold)) / 1166 ctlr->imu_avg_delta_ms; 1167 ctlr->imu_timestamp_us += 1000 * ctlr->imu_avg_delta_ms; 1168 if (dropped_pkts > JC_IMU_DROPPED_PKT_WARNING) { 1169 hid_warn(ctlr->hdev, 1170 "compensating for %u dropped IMU reports\n", 1171 dropped_pkts); 1172 hid_warn(ctlr->hdev, 1173 "delta=%u avg_delta=%u\n", 1174 delta, ctlr->imu_avg_delta_ms); 1175 } 1176 } 1177 ctlr->imu_last_pkt_ms = msecs; 1178 1179 /* Each IMU input report contains three samples */ 1180 for (i = 0; i < 3; i++) { 1181 input_event(idev, EV_MSC, MSC_TIMESTAMP, 1182 ctlr->imu_timestamp_us); 1183 1184 /* 1185 * These calculations (which use the controller's calibration 1186 * settings to improve the final values) are based on those 1187 * found in the community's reverse-engineering repo (linked at 1188 * top of driver). For hid-nintendo, we make sure that the final 1189 * value given to userspace is always in terms of the axis 1190 * resolution we provided. 1191 * 1192 * Currently only the gyro calculations subtract the calibration 1193 * offsets from the raw value itself. In testing, doing the same 1194 * for the accelerometer raw values decreased accuracy. 1195 * 1196 * Note that the gyro values are multiplied by the 1197 * precision-saving scaling factor to prevent large inaccuracies 1198 * due to truncation of the resolution value which would 1199 * otherwise occur. To prevent overflow (without resorting to 64 1200 * bit integer math), the mult_frac macro is used. 1201 */ 1202 value[0] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1203 (imu_data[i].gyro_x - 1204 ctlr->gyro_cal.offset[0])), 1205 ctlr->gyro_cal.scale[0], 1206 ctlr->imu_cal_gyro_divisor[0]); 1207 value[1] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1208 (imu_data[i].gyro_y - 1209 ctlr->gyro_cal.offset[1])), 1210 ctlr->gyro_cal.scale[1], 1211 ctlr->imu_cal_gyro_divisor[1]); 1212 value[2] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1213 (imu_data[i].gyro_z - 1214 ctlr->gyro_cal.offset[2])), 1215 ctlr->gyro_cal.scale[2], 1216 ctlr->imu_cal_gyro_divisor[2]); 1217 1218 value[3] = ((s32)imu_data[i].accel_x * 1219 ctlr->accel_cal.scale[0]) / 1220 ctlr->imu_cal_accel_divisor[0]; 1221 value[4] = ((s32)imu_data[i].accel_y * 1222 ctlr->accel_cal.scale[1]) / 1223 ctlr->imu_cal_accel_divisor[1]; 1224 value[5] = ((s32)imu_data[i].accel_z * 1225 ctlr->accel_cal.scale[2]) / 1226 ctlr->imu_cal_accel_divisor[2]; 1227 1228 hid_dbg(ctlr->hdev, "raw_gyro: g_x=%d g_y=%d g_z=%d\n", 1229 imu_data[i].gyro_x, imu_data[i].gyro_y, 1230 imu_data[i].gyro_z); 1231 hid_dbg(ctlr->hdev, "raw_accel: a_x=%d a_y=%d a_z=%d\n", 1232 imu_data[i].accel_x, imu_data[i].accel_y, 1233 imu_data[i].accel_z); 1234 1235 /* 1236 * The right joy-con has 2 axes negated, Y and Z. This is due to 1237 * the orientation of the IMU in the controller. We negate those 1238 * axes' values in order to be consistent with the left joy-con 1239 * and the pro controller: 1240 * X: positive is pointing toward the triggers 1241 * Y: positive is pointing to the left 1242 * Z: positive is pointing up (out of the buttons/sticks) 1243 * The axes follow the right-hand rule. 1244 */ 1245 if (jc_type_is_joycon(ctlr) && jc_type_has_right(ctlr)) { 1246 int j; 1247 1248 /* negate all but x axis */ 1249 for (j = 1; j < 6; ++j) { 1250 if (j == 3) 1251 continue; 1252 value[j] *= -1; 1253 } 1254 } 1255 1256 input_report_abs(idev, ABS_RX, value[0]); 1257 input_report_abs(idev, ABS_RY, value[1]); 1258 input_report_abs(idev, ABS_RZ, value[2]); 1259 input_report_abs(idev, ABS_X, value[3]); 1260 input_report_abs(idev, ABS_Y, value[4]); 1261 input_report_abs(idev, ABS_Z, value[5]); 1262 input_sync(idev); 1263 /* convert to micros and divide by 3 (3 samples per report). */ 1264 ctlr->imu_timestamp_us += ctlr->imu_avg_delta_ms * 1000 / 3; 1265 } 1266 } 1267 1268 static void joycon_parse_report(struct joycon_ctlr *ctlr, 1269 struct joycon_input_report *rep) 1270 { 1271 struct input_dev *dev = ctlr->input; 1272 unsigned long flags; 1273 u8 tmp; 1274 u32 btns; 1275 unsigned long msecs = jiffies_to_msecs(jiffies); 1276 unsigned long report_delta_ms = msecs - ctlr->last_input_report_msecs; 1277 1278 spin_lock_irqsave(&ctlr->lock, flags); 1279 if (IS_ENABLED(CONFIG_NINTENDO_FF) && rep->vibrator_report && 1280 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED && 1281 (msecs - ctlr->rumble_msecs) >= JC_RUMBLE_PERIOD_MS && 1282 (ctlr->rumble_queue_head != ctlr->rumble_queue_tail || 1283 ctlr->rumble_zero_countdown > 0)) { 1284 /* 1285 * When this value reaches 0, we know we've sent multiple 1286 * packets to the controller instructing it to disable rumble. 1287 * We can safely stop sending periodic rumble packets until the 1288 * next ff effect. 1289 */ 1290 if (ctlr->rumble_zero_countdown > 0) 1291 ctlr->rumble_zero_countdown--; 1292 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1293 } 1294 1295 /* Parse the battery status */ 1296 tmp = rep->bat_con; 1297 ctlr->host_powered = tmp & BIT(0); 1298 ctlr->battery_charging = tmp & BIT(4); 1299 tmp = tmp >> 5; 1300 switch (tmp) { 1301 case 0: /* empty */ 1302 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; 1303 break; 1304 case 1: /* low */ 1305 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_LOW; 1306 break; 1307 case 2: /* medium */ 1308 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; 1309 break; 1310 case 3: /* high */ 1311 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_HIGH; 1312 break; 1313 case 4: /* full */ 1314 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_FULL; 1315 break; 1316 default: 1317 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 1318 hid_warn(ctlr->hdev, "Invalid battery status\n"); 1319 break; 1320 } 1321 spin_unlock_irqrestore(&ctlr->lock, flags); 1322 1323 /* Parse the buttons and sticks */ 1324 btns = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1325 1326 if (jc_type_has_left(ctlr)) { 1327 u16 raw_x; 1328 u16 raw_y; 1329 s32 x; 1330 s32 y; 1331 1332 /* get raw stick values */ 1333 raw_x = hid_field_extract(ctlr->hdev, rep->left_stick, 0, 12); 1334 raw_y = hid_field_extract(ctlr->hdev, 1335 rep->left_stick + 1, 4, 12); 1336 /* map the stick values */ 1337 x = joycon_map_stick_val(&ctlr->left_stick_cal_x, raw_x); 1338 y = -joycon_map_stick_val(&ctlr->left_stick_cal_y, raw_y); 1339 /* report sticks */ 1340 input_report_abs(dev, ABS_X, x); 1341 input_report_abs(dev, ABS_Y, y); 1342 1343 /* report buttons */ 1344 input_report_key(dev, BTN_TL, btns & JC_BTN_L); 1345 input_report_key(dev, BTN_TL2, btns & JC_BTN_ZL); 1346 input_report_key(dev, BTN_SELECT, btns & JC_BTN_MINUS); 1347 input_report_key(dev, BTN_THUMBL, btns & JC_BTN_LSTICK); 1348 input_report_key(dev, BTN_Z, btns & JC_BTN_CAP); 1349 1350 if (jc_type_is_joycon(ctlr)) { 1351 /* Report the S buttons as the non-existent triggers */ 1352 input_report_key(dev, BTN_TR, btns & JC_BTN_SL_L); 1353 input_report_key(dev, BTN_TR2, btns & JC_BTN_SR_L); 1354 1355 /* Report d-pad as digital buttons for the joy-cons */ 1356 input_report_key(dev, BTN_DPAD_DOWN, 1357 btns & JC_BTN_DOWN); 1358 input_report_key(dev, BTN_DPAD_UP, btns & JC_BTN_UP); 1359 input_report_key(dev, BTN_DPAD_RIGHT, 1360 btns & JC_BTN_RIGHT); 1361 input_report_key(dev, BTN_DPAD_LEFT, 1362 btns & JC_BTN_LEFT); 1363 } else { 1364 int hatx = 0; 1365 int haty = 0; 1366 1367 /* d-pad x */ 1368 if (btns & JC_BTN_LEFT) 1369 hatx = -1; 1370 else if (btns & JC_BTN_RIGHT) 1371 hatx = 1; 1372 input_report_abs(dev, ABS_HAT0X, hatx); 1373 1374 /* d-pad y */ 1375 if (btns & JC_BTN_UP) 1376 haty = -1; 1377 else if (btns & JC_BTN_DOWN) 1378 haty = 1; 1379 input_report_abs(dev, ABS_HAT0Y, haty); 1380 } 1381 } 1382 if (jc_type_has_right(ctlr)) { 1383 u16 raw_x; 1384 u16 raw_y; 1385 s32 x; 1386 s32 y; 1387 1388 /* get raw stick values */ 1389 raw_x = hid_field_extract(ctlr->hdev, rep->right_stick, 0, 12); 1390 raw_y = hid_field_extract(ctlr->hdev, 1391 rep->right_stick + 1, 4, 12); 1392 /* map stick values */ 1393 x = joycon_map_stick_val(&ctlr->right_stick_cal_x, raw_x); 1394 y = -joycon_map_stick_val(&ctlr->right_stick_cal_y, raw_y); 1395 /* report sticks */ 1396 input_report_abs(dev, ABS_RX, x); 1397 input_report_abs(dev, ABS_RY, y); 1398 1399 /* report buttons */ 1400 input_report_key(dev, BTN_TR, btns & JC_BTN_R); 1401 input_report_key(dev, BTN_TR2, btns & JC_BTN_ZR); 1402 if (jc_type_is_joycon(ctlr)) { 1403 /* Report the S buttons as the non-existent triggers */ 1404 input_report_key(dev, BTN_TL, btns & JC_BTN_SL_R); 1405 input_report_key(dev, BTN_TL2, btns & JC_BTN_SR_R); 1406 } 1407 input_report_key(dev, BTN_START, btns & JC_BTN_PLUS); 1408 input_report_key(dev, BTN_THUMBR, btns & JC_BTN_RSTICK); 1409 input_report_key(dev, BTN_MODE, btns & JC_BTN_HOME); 1410 input_report_key(dev, BTN_WEST, btns & JC_BTN_Y); 1411 input_report_key(dev, BTN_NORTH, btns & JC_BTN_X); 1412 input_report_key(dev, BTN_EAST, btns & JC_BTN_A); 1413 input_report_key(dev, BTN_SOUTH, btns & JC_BTN_B); 1414 } 1415 1416 input_sync(dev); 1417 1418 spin_lock_irqsave(&ctlr->lock, flags); 1419 ctlr->last_input_report_msecs = msecs; 1420 /* 1421 * Was this input report a reasonable time delta compared to the prior 1422 * report? We use this information to decide when a safe time is to send 1423 * rumble packets or subcommand packets. 1424 */ 1425 if (report_delta_ms >= JC_INPUT_REPORT_MIN_DELTA && 1426 report_delta_ms <= JC_INPUT_REPORT_MAX_DELTA) { 1427 if (ctlr->consecutive_valid_report_deltas < JC_SUBCMD_VALID_DELTA_REQ) 1428 ctlr->consecutive_valid_report_deltas++; 1429 } else { 1430 ctlr->consecutive_valid_report_deltas = 0; 1431 } 1432 /* 1433 * Our consecutive valid report tracking is only relevant for 1434 * bluetooth-connected controllers. For USB devices, we're beholden to 1435 * USB's underlying polling rate anyway. Always set to the consecutive 1436 * delta requirement. 1437 */ 1438 if (ctlr->hdev->bus == BUS_USB) 1439 ctlr->consecutive_valid_report_deltas = JC_SUBCMD_VALID_DELTA_REQ; 1440 1441 spin_unlock_irqrestore(&ctlr->lock, flags); 1442 1443 /* 1444 * Immediately after receiving a report is the most reliable time to 1445 * send a subcommand to the controller. Wake any subcommand senders 1446 * waiting for a report. 1447 */ 1448 if (unlikely(mutex_is_locked(&ctlr->output_mutex))) { 1449 spin_lock_irqsave(&ctlr->lock, flags); 1450 ctlr->received_input_report = true; 1451 spin_unlock_irqrestore(&ctlr->lock, flags); 1452 wake_up(&ctlr->wait); 1453 } 1454 1455 /* parse IMU data if present */ 1456 if (rep->id == JC_INPUT_IMU_DATA) 1457 joycon_parse_imu_report(ctlr, rep); 1458 } 1459 1460 static int joycon_send_rumble_data(struct joycon_ctlr *ctlr) 1461 { 1462 int ret; 1463 unsigned long flags; 1464 struct joycon_rumble_output rumble_output = { 0 }; 1465 1466 spin_lock_irqsave(&ctlr->lock, flags); 1467 /* 1468 * If the controller has been removed, just return ENODEV so the LED 1469 * subsystem doesn't print invalid errors on removal. 1470 */ 1471 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 1472 spin_unlock_irqrestore(&ctlr->lock, flags); 1473 return -ENODEV; 1474 } 1475 memcpy(rumble_output.rumble_data, 1476 ctlr->rumble_data[ctlr->rumble_queue_tail], 1477 JC_RUMBLE_DATA_SIZE); 1478 spin_unlock_irqrestore(&ctlr->lock, flags); 1479 1480 rumble_output.output_id = JC_OUTPUT_RUMBLE_ONLY; 1481 rumble_output.packet_num = ctlr->subcmd_num; 1482 if (++ctlr->subcmd_num > 0xF) 1483 ctlr->subcmd_num = 0; 1484 1485 joycon_enforce_subcmd_rate(ctlr); 1486 1487 ret = __joycon_hid_send(ctlr->hdev, (u8 *)&rumble_output, 1488 sizeof(rumble_output)); 1489 return ret; 1490 } 1491 1492 static void joycon_rumble_worker(struct work_struct *work) 1493 { 1494 struct joycon_ctlr *ctlr = container_of(work, struct joycon_ctlr, 1495 rumble_worker); 1496 unsigned long flags; 1497 bool again = true; 1498 int ret; 1499 1500 while (again) { 1501 mutex_lock(&ctlr->output_mutex); 1502 ret = joycon_send_rumble_data(ctlr); 1503 mutex_unlock(&ctlr->output_mutex); 1504 1505 /* -ENODEV means the controller was just unplugged */ 1506 spin_lock_irqsave(&ctlr->lock, flags); 1507 if (ret < 0 && ret != -ENODEV && 1508 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1509 hid_warn(ctlr->hdev, "Failed to set rumble; e=%d", ret); 1510 1511 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1512 if (ctlr->rumble_queue_tail != ctlr->rumble_queue_head) { 1513 if (++ctlr->rumble_queue_tail >= JC_RUMBLE_QUEUE_SIZE) 1514 ctlr->rumble_queue_tail = 0; 1515 } else { 1516 again = false; 1517 } 1518 spin_unlock_irqrestore(&ctlr->lock, flags); 1519 } 1520 } 1521 1522 #if IS_ENABLED(CONFIG_NINTENDO_FF) 1523 static struct joycon_rumble_freq_data joycon_find_rumble_freq(u16 freq) 1524 { 1525 const size_t length = ARRAY_SIZE(joycon_rumble_frequencies); 1526 const struct joycon_rumble_freq_data *data = joycon_rumble_frequencies; 1527 int i = 0; 1528 1529 if (freq > data[0].freq) { 1530 for (i = 1; i < length - 1; i++) { 1531 if (freq > data[i - 1].freq && freq <= data[i].freq) 1532 break; 1533 } 1534 } 1535 1536 return data[i]; 1537 } 1538 1539 static struct joycon_rumble_amp_data joycon_find_rumble_amp(u16 amp) 1540 { 1541 const size_t length = ARRAY_SIZE(joycon_rumble_amplitudes); 1542 const struct joycon_rumble_amp_data *data = joycon_rumble_amplitudes; 1543 int i = 0; 1544 1545 if (amp > data[0].amp) { 1546 for (i = 1; i < length - 1; i++) { 1547 if (amp > data[i - 1].amp && amp <= data[i].amp) 1548 break; 1549 } 1550 } 1551 1552 return data[i]; 1553 } 1554 1555 static void joycon_encode_rumble(u8 *data, u16 freq_low, u16 freq_high, u16 amp) 1556 { 1557 struct joycon_rumble_freq_data freq_data_low; 1558 struct joycon_rumble_freq_data freq_data_high; 1559 struct joycon_rumble_amp_data amp_data; 1560 1561 freq_data_low = joycon_find_rumble_freq(freq_low); 1562 freq_data_high = joycon_find_rumble_freq(freq_high); 1563 amp_data = joycon_find_rumble_amp(amp); 1564 1565 data[0] = (freq_data_high.high >> 8) & 0xFF; 1566 data[1] = (freq_data_high.high & 0xFF) + amp_data.high; 1567 data[2] = freq_data_low.low + ((amp_data.low >> 8) & 0xFF); 1568 data[3] = amp_data.low & 0xFF; 1569 } 1570 1571 static const u16 JOYCON_MAX_RUMBLE_HIGH_FREQ = 1253; 1572 static const u16 JOYCON_MIN_RUMBLE_HIGH_FREQ = 82; 1573 static const u16 JOYCON_MAX_RUMBLE_LOW_FREQ = 626; 1574 static const u16 JOYCON_MIN_RUMBLE_LOW_FREQ = 41; 1575 1576 static void joycon_clamp_rumble_freqs(struct joycon_ctlr *ctlr) 1577 { 1578 unsigned long flags; 1579 1580 spin_lock_irqsave(&ctlr->lock, flags); 1581 ctlr->rumble_ll_freq = clamp(ctlr->rumble_ll_freq, 1582 JOYCON_MIN_RUMBLE_LOW_FREQ, 1583 JOYCON_MAX_RUMBLE_LOW_FREQ); 1584 ctlr->rumble_lh_freq = clamp(ctlr->rumble_lh_freq, 1585 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1586 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1587 ctlr->rumble_rl_freq = clamp(ctlr->rumble_rl_freq, 1588 JOYCON_MIN_RUMBLE_LOW_FREQ, 1589 JOYCON_MAX_RUMBLE_LOW_FREQ); 1590 ctlr->rumble_rh_freq = clamp(ctlr->rumble_rh_freq, 1591 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1592 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1593 spin_unlock_irqrestore(&ctlr->lock, flags); 1594 } 1595 1596 static int joycon_set_rumble(struct joycon_ctlr *ctlr, u16 amp_r, u16 amp_l, 1597 bool schedule_now) 1598 { 1599 u8 data[JC_RUMBLE_DATA_SIZE]; 1600 u16 amp; 1601 u16 freq_r_low; 1602 u16 freq_r_high; 1603 u16 freq_l_low; 1604 u16 freq_l_high; 1605 unsigned long flags; 1606 int next_rq_head; 1607 1608 spin_lock_irqsave(&ctlr->lock, flags); 1609 freq_r_low = ctlr->rumble_rl_freq; 1610 freq_r_high = ctlr->rumble_rh_freq; 1611 freq_l_low = ctlr->rumble_ll_freq; 1612 freq_l_high = ctlr->rumble_lh_freq; 1613 /* limit number of silent rumble packets to reduce traffic */ 1614 if (amp_l != 0 || amp_r != 0) 1615 ctlr->rumble_zero_countdown = JC_RUMBLE_ZERO_AMP_PKT_CNT; 1616 spin_unlock_irqrestore(&ctlr->lock, flags); 1617 1618 /* right joy-con */ 1619 amp = amp_r * (u32)joycon_max_rumble_amp / 65535; 1620 joycon_encode_rumble(data + 4, freq_r_low, freq_r_high, amp); 1621 1622 /* left joy-con */ 1623 amp = amp_l * (u32)joycon_max_rumble_amp / 65535; 1624 joycon_encode_rumble(data, freq_l_low, freq_l_high, amp); 1625 1626 spin_lock_irqsave(&ctlr->lock, flags); 1627 1628 next_rq_head = ctlr->rumble_queue_head + 1; 1629 if (next_rq_head >= JC_RUMBLE_QUEUE_SIZE) 1630 next_rq_head = 0; 1631 1632 /* Did we overrun the circular buffer? 1633 * If so, be sure we keep the latest intended rumble state. 1634 */ 1635 if (next_rq_head == ctlr->rumble_queue_tail) { 1636 hid_dbg(ctlr->hdev, "rumble queue is full"); 1637 /* overwrite the prior value at the end of the circular buf */ 1638 next_rq_head = ctlr->rumble_queue_head; 1639 } 1640 1641 ctlr->rumble_queue_head = next_rq_head; 1642 memcpy(ctlr->rumble_data[ctlr->rumble_queue_head], data, 1643 JC_RUMBLE_DATA_SIZE); 1644 1645 /* don't wait for the periodic send (reduces latency) */ 1646 if (schedule_now && ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1647 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1648 1649 spin_unlock_irqrestore(&ctlr->lock, flags); 1650 1651 return 0; 1652 } 1653 1654 static int joycon_play_effect(struct input_dev *dev, void *data, 1655 struct ff_effect *effect) 1656 { 1657 struct joycon_ctlr *ctlr = input_get_drvdata(dev); 1658 1659 if (effect->type != FF_RUMBLE) 1660 return 0; 1661 1662 return joycon_set_rumble(ctlr, 1663 effect->u.rumble.weak_magnitude, 1664 effect->u.rumble.strong_magnitude, 1665 true); 1666 } 1667 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 1668 1669 static const unsigned int joycon_button_inputs_l[] = { 1670 BTN_SELECT, BTN_Z, BTN_THUMBL, 1671 BTN_TL, BTN_TL2, 1672 0 /* 0 signals end of array */ 1673 }; 1674 1675 static const unsigned int joycon_button_inputs_r[] = { 1676 BTN_START, BTN_MODE, BTN_THUMBR, 1677 BTN_SOUTH, BTN_EAST, BTN_NORTH, BTN_WEST, 1678 BTN_TR, BTN_TR2, 1679 0 /* 0 signals end of array */ 1680 }; 1681 1682 /* We report joy-con d-pad inputs as buttons and pro controller as a hat. */ 1683 static const unsigned int joycon_dpad_inputs_jc[] = { 1684 BTN_DPAD_UP, BTN_DPAD_DOWN, BTN_DPAD_LEFT, BTN_DPAD_RIGHT, 1685 0 /* 0 signals end of array */ 1686 }; 1687 1688 static int joycon_input_create(struct joycon_ctlr *ctlr) 1689 { 1690 struct hid_device *hdev; 1691 const char *name; 1692 const char *imu_name; 1693 int ret; 1694 int i; 1695 1696 hdev = ctlr->hdev; 1697 1698 switch (hdev->product) { 1699 case USB_DEVICE_ID_NINTENDO_PROCON: 1700 name = "Nintendo Switch Pro Controller"; 1701 imu_name = "Nintendo Switch Pro Controller IMU"; 1702 break; 1703 case USB_DEVICE_ID_NINTENDO_CHRGGRIP: 1704 if (jc_type_has_left(ctlr)) { 1705 name = "Nintendo Switch Left Joy-Con (Grip)"; 1706 imu_name = "Nintendo Switch Left Joy-Con IMU (Grip)"; 1707 } else { 1708 name = "Nintendo Switch Right Joy-Con (Grip)"; 1709 imu_name = "Nintendo Switch Right Joy-Con IMU (Grip)"; 1710 } 1711 break; 1712 case USB_DEVICE_ID_NINTENDO_JOYCONL: 1713 name = "Nintendo Switch Left Joy-Con"; 1714 imu_name = "Nintendo Switch Left Joy-Con IMU"; 1715 break; 1716 case USB_DEVICE_ID_NINTENDO_JOYCONR: 1717 name = "Nintendo Switch Right Joy-Con"; 1718 imu_name = "Nintendo Switch Right Joy-Con IMU"; 1719 break; 1720 default: /* Should be impossible */ 1721 hid_err(hdev, "Invalid hid product\n"); 1722 return -EINVAL; 1723 } 1724 1725 ctlr->input = devm_input_allocate_device(&hdev->dev); 1726 if (!ctlr->input) 1727 return -ENOMEM; 1728 ctlr->input->id.bustype = hdev->bus; 1729 ctlr->input->id.vendor = hdev->vendor; 1730 ctlr->input->id.product = hdev->product; 1731 ctlr->input->id.version = hdev->version; 1732 ctlr->input->uniq = ctlr->mac_addr_str; 1733 ctlr->input->name = name; 1734 ctlr->input->phys = hdev->phys; 1735 input_set_drvdata(ctlr->input, ctlr); 1736 1737 /* set up sticks and buttons */ 1738 if (jc_type_has_left(ctlr)) { 1739 input_set_abs_params(ctlr->input, ABS_X, 1740 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1741 JC_STICK_FUZZ, JC_STICK_FLAT); 1742 input_set_abs_params(ctlr->input, ABS_Y, 1743 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1744 JC_STICK_FUZZ, JC_STICK_FLAT); 1745 1746 for (i = 0; joycon_button_inputs_l[i] > 0; i++) 1747 input_set_capability(ctlr->input, EV_KEY, 1748 joycon_button_inputs_l[i]); 1749 1750 /* configure d-pad differently for joy-con vs pro controller */ 1751 if (hdev->product != USB_DEVICE_ID_NINTENDO_PROCON) { 1752 for (i = 0; joycon_dpad_inputs_jc[i] > 0; i++) 1753 input_set_capability(ctlr->input, EV_KEY, 1754 joycon_dpad_inputs_jc[i]); 1755 } else { 1756 input_set_abs_params(ctlr->input, ABS_HAT0X, 1757 -JC_MAX_DPAD_MAG, JC_MAX_DPAD_MAG, 1758 JC_DPAD_FUZZ, JC_DPAD_FLAT); 1759 input_set_abs_params(ctlr->input, ABS_HAT0Y, 1760 -JC_MAX_DPAD_MAG, JC_MAX_DPAD_MAG, 1761 JC_DPAD_FUZZ, JC_DPAD_FLAT); 1762 } 1763 } 1764 if (jc_type_has_right(ctlr)) { 1765 input_set_abs_params(ctlr->input, ABS_RX, 1766 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1767 JC_STICK_FUZZ, JC_STICK_FLAT); 1768 input_set_abs_params(ctlr->input, ABS_RY, 1769 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1770 JC_STICK_FUZZ, JC_STICK_FLAT); 1771 1772 for (i = 0; joycon_button_inputs_r[i] > 0; i++) 1773 input_set_capability(ctlr->input, EV_KEY, 1774 joycon_button_inputs_r[i]); 1775 } 1776 1777 /* Let's report joy-con S triggers separately */ 1778 if (hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL) { 1779 input_set_capability(ctlr->input, EV_KEY, BTN_TR); 1780 input_set_capability(ctlr->input, EV_KEY, BTN_TR2); 1781 } else if (hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR) { 1782 input_set_capability(ctlr->input, EV_KEY, BTN_TL); 1783 input_set_capability(ctlr->input, EV_KEY, BTN_TL2); 1784 } 1785 1786 #if IS_ENABLED(CONFIG_NINTENDO_FF) 1787 /* set up rumble */ 1788 input_set_capability(ctlr->input, EV_FF, FF_RUMBLE); 1789 input_ff_create_memless(ctlr->input, NULL, joycon_play_effect); 1790 ctlr->rumble_ll_freq = JC_RUMBLE_DFLT_LOW_FREQ; 1791 ctlr->rumble_lh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 1792 ctlr->rumble_rl_freq = JC_RUMBLE_DFLT_LOW_FREQ; 1793 ctlr->rumble_rh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 1794 joycon_clamp_rumble_freqs(ctlr); 1795 joycon_set_rumble(ctlr, 0, 0, false); 1796 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1797 #endif 1798 1799 ret = input_register_device(ctlr->input); 1800 if (ret) 1801 return ret; 1802 1803 /* configure the imu input device */ 1804 ctlr->imu_input = devm_input_allocate_device(&hdev->dev); 1805 if (!ctlr->imu_input) 1806 return -ENOMEM; 1807 1808 ctlr->imu_input->id.bustype = hdev->bus; 1809 ctlr->imu_input->id.vendor = hdev->vendor; 1810 ctlr->imu_input->id.product = hdev->product; 1811 ctlr->imu_input->id.version = hdev->version; 1812 ctlr->imu_input->uniq = ctlr->mac_addr_str; 1813 ctlr->imu_input->name = imu_name; 1814 ctlr->imu_input->phys = hdev->phys; 1815 input_set_drvdata(ctlr->imu_input, ctlr); 1816 1817 /* configure imu axes */ 1818 input_set_abs_params(ctlr->imu_input, ABS_X, 1819 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1820 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1821 input_set_abs_params(ctlr->imu_input, ABS_Y, 1822 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1823 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1824 input_set_abs_params(ctlr->imu_input, ABS_Z, 1825 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1826 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1827 input_abs_set_res(ctlr->imu_input, ABS_X, JC_IMU_ACCEL_RES_PER_G); 1828 input_abs_set_res(ctlr->imu_input, ABS_Y, JC_IMU_ACCEL_RES_PER_G); 1829 input_abs_set_res(ctlr->imu_input, ABS_Z, JC_IMU_ACCEL_RES_PER_G); 1830 1831 input_set_abs_params(ctlr->imu_input, ABS_RX, 1832 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1833 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1834 input_set_abs_params(ctlr->imu_input, ABS_RY, 1835 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1836 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1837 input_set_abs_params(ctlr->imu_input, ABS_RZ, 1838 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1839 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1840 1841 input_abs_set_res(ctlr->imu_input, ABS_RX, JC_IMU_GYRO_RES_PER_DPS); 1842 input_abs_set_res(ctlr->imu_input, ABS_RY, JC_IMU_GYRO_RES_PER_DPS); 1843 input_abs_set_res(ctlr->imu_input, ABS_RZ, JC_IMU_GYRO_RES_PER_DPS); 1844 1845 __set_bit(EV_MSC, ctlr->imu_input->evbit); 1846 __set_bit(MSC_TIMESTAMP, ctlr->imu_input->mscbit); 1847 __set_bit(INPUT_PROP_ACCELEROMETER, ctlr->imu_input->propbit); 1848 1849 ret = input_register_device(ctlr->imu_input); 1850 if (ret) 1851 return ret; 1852 1853 return 0; 1854 } 1855 1856 static int joycon_player_led_brightness_set(struct led_classdev *led, 1857 enum led_brightness brightness) 1858 { 1859 struct device *dev = led->dev->parent; 1860 struct hid_device *hdev = to_hid_device(dev); 1861 struct joycon_ctlr *ctlr; 1862 int val = 0; 1863 int i; 1864 int ret; 1865 int num; 1866 1867 ctlr = hid_get_drvdata(hdev); 1868 if (!ctlr) { 1869 hid_err(hdev, "No controller data\n"); 1870 return -ENODEV; 1871 } 1872 1873 /* determine which player led this is */ 1874 for (num = 0; num < JC_NUM_LEDS; num++) { 1875 if (&ctlr->leds[num] == led) 1876 break; 1877 } 1878 if (num >= JC_NUM_LEDS) 1879 return -EINVAL; 1880 1881 mutex_lock(&ctlr->output_mutex); 1882 for (i = 0; i < JC_NUM_LEDS; i++) { 1883 if (i == num) 1884 val |= brightness << i; 1885 else 1886 val |= ctlr->leds[i].brightness << i; 1887 } 1888 ret = joycon_set_player_leds(ctlr, 0, val); 1889 mutex_unlock(&ctlr->output_mutex); 1890 1891 return ret; 1892 } 1893 1894 static int joycon_home_led_brightness_set(struct led_classdev *led, 1895 enum led_brightness brightness) 1896 { 1897 struct device *dev = led->dev->parent; 1898 struct hid_device *hdev = to_hid_device(dev); 1899 struct joycon_ctlr *ctlr; 1900 struct joycon_subcmd_request *req; 1901 u8 buffer[sizeof(*req) + 5] = { 0 }; 1902 u8 *data; 1903 int ret; 1904 1905 ctlr = hid_get_drvdata(hdev); 1906 if (!ctlr) { 1907 hid_err(hdev, "No controller data\n"); 1908 return -ENODEV; 1909 } 1910 1911 req = (struct joycon_subcmd_request *)buffer; 1912 req->subcmd_id = JC_SUBCMD_SET_HOME_LIGHT; 1913 data = req->data; 1914 data[0] = 0x01; 1915 data[1] = brightness << 4; 1916 data[2] = brightness | (brightness << 4); 1917 data[3] = 0x11; 1918 data[4] = 0x11; 1919 1920 hid_dbg(hdev, "setting home led brightness\n"); 1921 mutex_lock(&ctlr->output_mutex); 1922 ret = joycon_send_subcmd(ctlr, req, 5, HZ/4); 1923 mutex_unlock(&ctlr->output_mutex); 1924 1925 return ret; 1926 } 1927 1928 static DEFINE_MUTEX(joycon_input_num_mutex); 1929 static int joycon_leds_create(struct joycon_ctlr *ctlr) 1930 { 1931 struct hid_device *hdev = ctlr->hdev; 1932 struct device *dev = &hdev->dev; 1933 const char *d_name = dev_name(dev); 1934 struct led_classdev *led; 1935 char *name; 1936 int ret = 0; 1937 int i; 1938 static int input_num = 1; 1939 1940 /* Set the default controller player leds based on controller number */ 1941 mutex_lock(&joycon_input_num_mutex); 1942 mutex_lock(&ctlr->output_mutex); 1943 ret = joycon_set_player_leds(ctlr, 0, 0xF >> (4 - input_num)); 1944 if (ret) 1945 hid_warn(ctlr->hdev, "Failed to set leds; ret=%d\n", ret); 1946 mutex_unlock(&ctlr->output_mutex); 1947 1948 /* configure the player LEDs */ 1949 for (i = 0; i < JC_NUM_LEDS; i++) { 1950 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 1951 d_name, 1952 "green", 1953 joycon_player_led_names[i]); 1954 if (!name) { 1955 mutex_unlock(&joycon_input_num_mutex); 1956 return -ENOMEM; 1957 } 1958 1959 led = &ctlr->leds[i]; 1960 led->name = name; 1961 led->brightness = ((i + 1) <= input_num) ? 1 : 0; 1962 led->max_brightness = 1; 1963 led->brightness_set_blocking = 1964 joycon_player_led_brightness_set; 1965 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 1966 1967 ret = devm_led_classdev_register(&hdev->dev, led); 1968 if (ret) { 1969 hid_err(hdev, "Failed registering %s LED\n", led->name); 1970 mutex_unlock(&joycon_input_num_mutex); 1971 return ret; 1972 } 1973 } 1974 1975 if (++input_num > 4) 1976 input_num = 1; 1977 mutex_unlock(&joycon_input_num_mutex); 1978 1979 /* configure the home LED */ 1980 if (jc_type_has_right(ctlr)) { 1981 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 1982 d_name, 1983 "blue", 1984 LED_FUNCTION_PLAYER5); 1985 if (!name) 1986 return -ENOMEM; 1987 1988 led = &ctlr->home_led; 1989 led->name = name; 1990 led->brightness = 0; 1991 led->max_brightness = 0xF; 1992 led->brightness_set_blocking = joycon_home_led_brightness_set; 1993 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 1994 ret = devm_led_classdev_register(&hdev->dev, led); 1995 if (ret) { 1996 hid_err(hdev, "Failed registering home led\n"); 1997 return ret; 1998 } 1999 /* Set the home LED to 0 as default state */ 2000 ret = joycon_home_led_brightness_set(led, 0); 2001 if (ret) { 2002 hid_warn(hdev, "Failed to set home LED default, unregistering home LED"); 2003 devm_led_classdev_unregister(&hdev->dev, led); 2004 } 2005 } 2006 2007 return 0; 2008 } 2009 2010 static int joycon_battery_get_property(struct power_supply *supply, 2011 enum power_supply_property prop, 2012 union power_supply_propval *val) 2013 { 2014 struct joycon_ctlr *ctlr = power_supply_get_drvdata(supply); 2015 unsigned long flags; 2016 int ret = 0; 2017 u8 capacity; 2018 bool charging; 2019 bool powered; 2020 2021 spin_lock_irqsave(&ctlr->lock, flags); 2022 capacity = ctlr->battery_capacity; 2023 charging = ctlr->battery_charging; 2024 powered = ctlr->host_powered; 2025 spin_unlock_irqrestore(&ctlr->lock, flags); 2026 2027 switch (prop) { 2028 case POWER_SUPPLY_PROP_PRESENT: 2029 val->intval = 1; 2030 break; 2031 case POWER_SUPPLY_PROP_SCOPE: 2032 val->intval = POWER_SUPPLY_SCOPE_DEVICE; 2033 break; 2034 case POWER_SUPPLY_PROP_CAPACITY_LEVEL: 2035 val->intval = capacity; 2036 break; 2037 case POWER_SUPPLY_PROP_STATUS: 2038 if (charging) 2039 val->intval = POWER_SUPPLY_STATUS_CHARGING; 2040 else if (capacity == POWER_SUPPLY_CAPACITY_LEVEL_FULL && 2041 powered) 2042 val->intval = POWER_SUPPLY_STATUS_FULL; 2043 else 2044 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 2045 break; 2046 default: 2047 ret = -EINVAL; 2048 break; 2049 } 2050 return ret; 2051 } 2052 2053 static enum power_supply_property joycon_battery_props[] = { 2054 POWER_SUPPLY_PROP_PRESENT, 2055 POWER_SUPPLY_PROP_CAPACITY_LEVEL, 2056 POWER_SUPPLY_PROP_SCOPE, 2057 POWER_SUPPLY_PROP_STATUS, 2058 }; 2059 2060 static int joycon_power_supply_create(struct joycon_ctlr *ctlr) 2061 { 2062 struct hid_device *hdev = ctlr->hdev; 2063 struct power_supply_config supply_config = { .drv_data = ctlr, }; 2064 const char * const name_fmt = "nintendo_switch_controller_battery_%s"; 2065 int ret = 0; 2066 2067 /* Set initially to unknown before receiving first input report */ 2068 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 2069 2070 /* Configure the battery's description */ 2071 ctlr->battery_desc.properties = joycon_battery_props; 2072 ctlr->battery_desc.num_properties = 2073 ARRAY_SIZE(joycon_battery_props); 2074 ctlr->battery_desc.get_property = joycon_battery_get_property; 2075 ctlr->battery_desc.type = POWER_SUPPLY_TYPE_BATTERY; 2076 ctlr->battery_desc.use_for_apm = 0; 2077 ctlr->battery_desc.name = devm_kasprintf(&hdev->dev, GFP_KERNEL, 2078 name_fmt, 2079 dev_name(&hdev->dev)); 2080 if (!ctlr->battery_desc.name) 2081 return -ENOMEM; 2082 2083 ctlr->battery = devm_power_supply_register(&hdev->dev, 2084 &ctlr->battery_desc, 2085 &supply_config); 2086 if (IS_ERR(ctlr->battery)) { 2087 ret = PTR_ERR(ctlr->battery); 2088 hid_err(hdev, "Failed to register battery; ret=%d\n", ret); 2089 return ret; 2090 } 2091 2092 return power_supply_powers(ctlr->battery, &hdev->dev); 2093 } 2094 2095 static int joycon_read_info(struct joycon_ctlr *ctlr) 2096 { 2097 int ret; 2098 int i; 2099 int j; 2100 struct joycon_subcmd_request req = { 0 }; 2101 struct joycon_input_report *report; 2102 2103 req.subcmd_id = JC_SUBCMD_REQ_DEV_INFO; 2104 mutex_lock(&ctlr->output_mutex); 2105 ret = joycon_send_subcmd(ctlr, &req, 0, HZ); 2106 mutex_unlock(&ctlr->output_mutex); 2107 if (ret) { 2108 hid_err(ctlr->hdev, "Failed to get joycon info; ret=%d\n", ret); 2109 return ret; 2110 } 2111 2112 report = (struct joycon_input_report *)ctlr->input_buf; 2113 2114 for (i = 4, j = 0; j < 6; i++, j++) 2115 ctlr->mac_addr[j] = report->subcmd_reply.data[i]; 2116 2117 ctlr->mac_addr_str = devm_kasprintf(&ctlr->hdev->dev, GFP_KERNEL, 2118 "%02X:%02X:%02X:%02X:%02X:%02X", 2119 ctlr->mac_addr[0], 2120 ctlr->mac_addr[1], 2121 ctlr->mac_addr[2], 2122 ctlr->mac_addr[3], 2123 ctlr->mac_addr[4], 2124 ctlr->mac_addr[5]); 2125 if (!ctlr->mac_addr_str) 2126 return -ENOMEM; 2127 hid_info(ctlr->hdev, "controller MAC = %s\n", ctlr->mac_addr_str); 2128 2129 /* Retrieve the type so we can distinguish for charging grip */ 2130 ctlr->ctlr_type = report->subcmd_reply.data[2]; 2131 2132 return 0; 2133 } 2134 2135 static int joycon_init(struct hid_device *hdev) 2136 { 2137 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2138 int ret = 0; 2139 2140 mutex_lock(&ctlr->output_mutex); 2141 /* if handshake command fails, assume ble pro controller */ 2142 if ((jc_type_is_procon(ctlr) || jc_type_is_chrggrip(ctlr)) && 2143 !joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ)) { 2144 hid_dbg(hdev, "detected USB controller\n"); 2145 /* set baudrate for improved latency */ 2146 ret = joycon_send_usb(ctlr, JC_USB_CMD_BAUDRATE_3M, HZ); 2147 if (ret) { 2148 hid_err(hdev, "Failed to set baudrate; ret=%d\n", ret); 2149 goto out_unlock; 2150 } 2151 /* handshake */ 2152 ret = joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ); 2153 if (ret) { 2154 hid_err(hdev, "Failed handshake; ret=%d\n", ret); 2155 goto out_unlock; 2156 } 2157 /* 2158 * Set no timeout (to keep controller in USB mode). 2159 * This doesn't send a response, so ignore the timeout. 2160 */ 2161 joycon_send_usb(ctlr, JC_USB_CMD_NO_TIMEOUT, HZ/10); 2162 } else if (jc_type_is_chrggrip(ctlr)) { 2163 hid_err(hdev, "Failed charging grip handshake\n"); 2164 ret = -ETIMEDOUT; 2165 goto out_unlock; 2166 } 2167 2168 /* get controller calibration data, and parse it */ 2169 ret = joycon_request_calibration(ctlr); 2170 if (ret) { 2171 /* 2172 * We can function with default calibration, but it may be 2173 * inaccurate. Provide a warning, and continue on. 2174 */ 2175 hid_warn(hdev, "Analog stick positions may be inaccurate\n"); 2176 } 2177 2178 /* get IMU calibration data, and parse it */ 2179 ret = joycon_request_imu_calibration(ctlr); 2180 if (ret) { 2181 /* 2182 * We can function with default calibration, but it may be 2183 * inaccurate. Provide a warning, and continue on. 2184 */ 2185 hid_warn(hdev, "Unable to read IMU calibration data\n"); 2186 } 2187 2188 /* Set the reporting mode to 0x30, which is the full report mode */ 2189 ret = joycon_set_report_mode(ctlr); 2190 if (ret) { 2191 hid_err(hdev, "Failed to set report mode; ret=%d\n", ret); 2192 goto out_unlock; 2193 } 2194 2195 /* Enable rumble */ 2196 ret = joycon_enable_rumble(ctlr); 2197 if (ret) { 2198 hid_err(hdev, "Failed to enable rumble; ret=%d\n", ret); 2199 goto out_unlock; 2200 } 2201 2202 /* Enable the IMU */ 2203 ret = joycon_enable_imu(ctlr); 2204 if (ret) { 2205 hid_err(hdev, "Failed to enable the IMU; ret=%d\n", ret); 2206 goto out_unlock; 2207 } 2208 2209 out_unlock: 2210 mutex_unlock(&ctlr->output_mutex); 2211 return ret; 2212 } 2213 2214 /* Common handler for parsing inputs */ 2215 static int joycon_ctlr_read_handler(struct joycon_ctlr *ctlr, u8 *data, 2216 int size) 2217 { 2218 if (data[0] == JC_INPUT_SUBCMD_REPLY || data[0] == JC_INPUT_IMU_DATA || 2219 data[0] == JC_INPUT_MCU_DATA) { 2220 if (size >= 12) /* make sure it contains the input report */ 2221 joycon_parse_report(ctlr, 2222 (struct joycon_input_report *)data); 2223 } 2224 2225 return 0; 2226 } 2227 2228 static int joycon_ctlr_handle_event(struct joycon_ctlr *ctlr, u8 *data, 2229 int size) 2230 { 2231 int ret = 0; 2232 bool match = false; 2233 struct joycon_input_report *report; 2234 2235 if (unlikely(mutex_is_locked(&ctlr->output_mutex)) && 2236 ctlr->msg_type != JOYCON_MSG_TYPE_NONE) { 2237 switch (ctlr->msg_type) { 2238 case JOYCON_MSG_TYPE_USB: 2239 if (size < 2) 2240 break; 2241 if (data[0] == JC_INPUT_USB_RESPONSE && 2242 data[1] == ctlr->usb_ack_match) 2243 match = true; 2244 break; 2245 case JOYCON_MSG_TYPE_SUBCMD: 2246 if (size < sizeof(struct joycon_input_report) || 2247 data[0] != JC_INPUT_SUBCMD_REPLY) 2248 break; 2249 report = (struct joycon_input_report *)data; 2250 if (report->subcmd_reply.id == ctlr->subcmd_ack_match) 2251 match = true; 2252 break; 2253 default: 2254 break; 2255 } 2256 2257 if (match) { 2258 memcpy(ctlr->input_buf, data, 2259 min(size, (int)JC_MAX_RESP_SIZE)); 2260 ctlr->msg_type = JOYCON_MSG_TYPE_NONE; 2261 ctlr->received_resp = true; 2262 wake_up(&ctlr->wait); 2263 2264 /* This message has been handled */ 2265 return 1; 2266 } 2267 } 2268 2269 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) 2270 ret = joycon_ctlr_read_handler(ctlr, data, size); 2271 2272 return ret; 2273 } 2274 2275 static int nintendo_hid_event(struct hid_device *hdev, 2276 struct hid_report *report, u8 *raw_data, int size) 2277 { 2278 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2279 2280 if (size < 1) 2281 return -EINVAL; 2282 2283 return joycon_ctlr_handle_event(ctlr, raw_data, size); 2284 } 2285 2286 static int nintendo_hid_probe(struct hid_device *hdev, 2287 const struct hid_device_id *id) 2288 { 2289 int ret; 2290 struct joycon_ctlr *ctlr; 2291 2292 hid_dbg(hdev, "probe - start\n"); 2293 2294 ctlr = devm_kzalloc(&hdev->dev, sizeof(*ctlr), GFP_KERNEL); 2295 if (!ctlr) { 2296 ret = -ENOMEM; 2297 goto err; 2298 } 2299 2300 ctlr->hdev = hdev; 2301 ctlr->ctlr_state = JOYCON_CTLR_STATE_INIT; 2302 ctlr->rumble_queue_head = 0; 2303 ctlr->rumble_queue_tail = 0; 2304 hid_set_drvdata(hdev, ctlr); 2305 mutex_init(&ctlr->output_mutex); 2306 init_waitqueue_head(&ctlr->wait); 2307 spin_lock_init(&ctlr->lock); 2308 ctlr->rumble_queue = alloc_workqueue("hid-nintendo-rumble_wq", 2309 WQ_FREEZABLE | WQ_MEM_RECLAIM, 0); 2310 if (!ctlr->rumble_queue) { 2311 ret = -ENOMEM; 2312 goto err; 2313 } 2314 INIT_WORK(&ctlr->rumble_worker, joycon_rumble_worker); 2315 2316 ret = hid_parse(hdev); 2317 if (ret) { 2318 hid_err(hdev, "HID parse failed\n"); 2319 goto err_wq; 2320 } 2321 2322 /* 2323 * Patch the hw version of pro controller/joycons, so applications can 2324 * distinguish between the default HID mappings and the mappings defined 2325 * by the Linux game controller spec. This is important for the SDL2 2326 * library, which has a game controller database, which uses device ids 2327 * in combination with version as a key. 2328 */ 2329 hdev->version |= 0x8000; 2330 2331 ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW); 2332 if (ret) { 2333 hid_err(hdev, "HW start failed\n"); 2334 goto err_wq; 2335 } 2336 2337 ret = hid_hw_open(hdev); 2338 if (ret) { 2339 hid_err(hdev, "cannot start hardware I/O\n"); 2340 goto err_stop; 2341 } 2342 2343 hid_device_io_start(hdev); 2344 2345 ret = joycon_init(hdev); 2346 if (ret) { 2347 hid_err(hdev, "Failed to initialize controller; ret=%d\n", ret); 2348 goto err_close; 2349 } 2350 2351 ret = joycon_read_info(ctlr); 2352 if (ret) { 2353 hid_err(hdev, "Failed to retrieve controller info; ret=%d\n", 2354 ret); 2355 goto err_close; 2356 } 2357 2358 /* Initialize the leds */ 2359 ret = joycon_leds_create(ctlr); 2360 if (ret) { 2361 hid_err(hdev, "Failed to create leds; ret=%d\n", ret); 2362 goto err_close; 2363 } 2364 2365 /* Initialize the battery power supply */ 2366 ret = joycon_power_supply_create(ctlr); 2367 if (ret) { 2368 hid_err(hdev, "Failed to create power_supply; ret=%d\n", ret); 2369 goto err_close; 2370 } 2371 2372 ret = joycon_input_create(ctlr); 2373 if (ret) { 2374 hid_err(hdev, "Failed to create input device; ret=%d\n", ret); 2375 goto err_close; 2376 } 2377 2378 ctlr->ctlr_state = JOYCON_CTLR_STATE_READ; 2379 2380 hid_dbg(hdev, "probe - success\n"); 2381 return 0; 2382 2383 err_close: 2384 hid_hw_close(hdev); 2385 err_stop: 2386 hid_hw_stop(hdev); 2387 err_wq: 2388 destroy_workqueue(ctlr->rumble_queue); 2389 err: 2390 hid_err(hdev, "probe - fail = %d\n", ret); 2391 return ret; 2392 } 2393 2394 static void nintendo_hid_remove(struct hid_device *hdev) 2395 { 2396 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2397 unsigned long flags; 2398 2399 hid_dbg(hdev, "remove\n"); 2400 2401 /* Prevent further attempts at sending subcommands. */ 2402 spin_lock_irqsave(&ctlr->lock, flags); 2403 ctlr->ctlr_state = JOYCON_CTLR_STATE_REMOVED; 2404 spin_unlock_irqrestore(&ctlr->lock, flags); 2405 2406 destroy_workqueue(ctlr->rumble_queue); 2407 2408 hid_hw_close(hdev); 2409 hid_hw_stop(hdev); 2410 } 2411 2412 #ifdef CONFIG_PM 2413 2414 static int nintendo_hid_resume(struct hid_device *hdev) 2415 { 2416 int ret = joycon_init(hdev); 2417 2418 if (ret) 2419 hid_err(hdev, "Failed to restore controller after resume"); 2420 2421 return ret; 2422 } 2423 2424 #endif 2425 2426 static const struct hid_device_id nintendo_hid_devices[] = { 2427 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2428 USB_DEVICE_ID_NINTENDO_PROCON) }, 2429 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2430 USB_DEVICE_ID_NINTENDO_PROCON) }, 2431 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2432 USB_DEVICE_ID_NINTENDO_CHRGGRIP) }, 2433 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2434 USB_DEVICE_ID_NINTENDO_JOYCONL) }, 2435 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2436 USB_DEVICE_ID_NINTENDO_JOYCONR) }, 2437 { } 2438 }; 2439 MODULE_DEVICE_TABLE(hid, nintendo_hid_devices); 2440 2441 static struct hid_driver nintendo_hid_driver = { 2442 .name = "nintendo", 2443 .id_table = nintendo_hid_devices, 2444 .probe = nintendo_hid_probe, 2445 .remove = nintendo_hid_remove, 2446 .raw_event = nintendo_hid_event, 2447 2448 #ifdef CONFIG_PM 2449 .resume = nintendo_hid_resume, 2450 #endif 2451 }; 2452 module_hid_driver(nintendo_hid_driver); 2453 2454 MODULE_LICENSE("GPL"); 2455 MODULE_AUTHOR("Daniel J. Ogorchock <djogorchock@gmail.com>"); 2456 MODULE_DESCRIPTION("Driver for Nintendo Switch Controllers"); 2457 2458