1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * HID driver for Nintendo Switch Joy-Cons and Pro Controllers 4 * 5 * Copyright (c) 2019-2021 Daniel J. Ogorchock <djogorchock@gmail.com> 6 * 7 * The following resources/projects were referenced for this driver: 8 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 9 * https://gitlab.com/pjranki/joycon-linux-kernel (Peter Rankin) 10 * https://github.com/FrotBot/SwitchProConLinuxUSB 11 * https://github.com/MTCKC/ProconXInput 12 * https://github.com/Davidobot/BetterJoyForCemu 13 * hid-wiimote kernel hid driver 14 * hid-logitech-hidpp driver 15 * hid-sony driver 16 * 17 * This driver supports the Nintendo Switch Joy-Cons and Pro Controllers. The 18 * Pro Controllers can either be used over USB or Bluetooth. 19 * 20 * The driver will retrieve the factory calibration info from the controllers, 21 * so little to no user calibration should be required. 22 * 23 */ 24 25 #include "hid-ids.h" 26 #include <asm/unaligned.h> 27 #include <linux/delay.h> 28 #include <linux/device.h> 29 #include <linux/kernel.h> 30 #include <linux/hid.h> 31 #include <linux/input.h> 32 #include <linux/jiffies.h> 33 #include <linux/leds.h> 34 #include <linux/module.h> 35 #include <linux/power_supply.h> 36 #include <linux/spinlock.h> 37 38 /* 39 * Reference the url below for the following HID report defines: 40 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 41 */ 42 43 /* Output Reports */ 44 #define JC_OUTPUT_RUMBLE_AND_SUBCMD 0x01 45 #define JC_OUTPUT_FW_UPDATE_PKT 0x03 46 #define JC_OUTPUT_RUMBLE_ONLY 0x10 47 #define JC_OUTPUT_MCU_DATA 0x11 48 #define JC_OUTPUT_USB_CMD 0x80 49 50 /* Subcommand IDs */ 51 #define JC_SUBCMD_STATE 0x00 52 #define JC_SUBCMD_MANUAL_BT_PAIRING 0x01 53 #define JC_SUBCMD_REQ_DEV_INFO 0x02 54 #define JC_SUBCMD_SET_REPORT_MODE 0x03 55 #define JC_SUBCMD_TRIGGERS_ELAPSED 0x04 56 #define JC_SUBCMD_GET_PAGE_LIST_STATE 0x05 57 #define JC_SUBCMD_SET_HCI_STATE 0x06 58 #define JC_SUBCMD_RESET_PAIRING_INFO 0x07 59 #define JC_SUBCMD_LOW_POWER_MODE 0x08 60 #define JC_SUBCMD_SPI_FLASH_READ 0x10 61 #define JC_SUBCMD_SPI_FLASH_WRITE 0x11 62 #define JC_SUBCMD_RESET_MCU 0x20 63 #define JC_SUBCMD_SET_MCU_CONFIG 0x21 64 #define JC_SUBCMD_SET_MCU_STATE 0x22 65 #define JC_SUBCMD_SET_PLAYER_LIGHTS 0x30 66 #define JC_SUBCMD_GET_PLAYER_LIGHTS 0x31 67 #define JC_SUBCMD_SET_HOME_LIGHT 0x38 68 #define JC_SUBCMD_ENABLE_IMU 0x40 69 #define JC_SUBCMD_SET_IMU_SENSITIVITY 0x41 70 #define JC_SUBCMD_WRITE_IMU_REG 0x42 71 #define JC_SUBCMD_READ_IMU_REG 0x43 72 #define JC_SUBCMD_ENABLE_VIBRATION 0x48 73 #define JC_SUBCMD_GET_REGULATED_VOLTAGE 0x50 74 75 /* Input Reports */ 76 #define JC_INPUT_BUTTON_EVENT 0x3F 77 #define JC_INPUT_SUBCMD_REPLY 0x21 78 #define JC_INPUT_IMU_DATA 0x30 79 #define JC_INPUT_MCU_DATA 0x31 80 #define JC_INPUT_USB_RESPONSE 0x81 81 82 /* Feature Reports */ 83 #define JC_FEATURE_LAST_SUBCMD 0x02 84 #define JC_FEATURE_OTA_FW_UPGRADE 0x70 85 #define JC_FEATURE_SETUP_MEM_READ 0x71 86 #define JC_FEATURE_MEM_READ 0x72 87 #define JC_FEATURE_ERASE_MEM_SECTOR 0x73 88 #define JC_FEATURE_MEM_WRITE 0x74 89 #define JC_FEATURE_LAUNCH 0x75 90 91 /* USB Commands */ 92 #define JC_USB_CMD_CONN_STATUS 0x01 93 #define JC_USB_CMD_HANDSHAKE 0x02 94 #define JC_USB_CMD_BAUDRATE_3M 0x03 95 #define JC_USB_CMD_NO_TIMEOUT 0x04 96 #define JC_USB_CMD_EN_TIMEOUT 0x05 97 #define JC_USB_RESET 0x06 98 #define JC_USB_PRE_HANDSHAKE 0x91 99 #define JC_USB_SEND_UART 0x92 100 101 /* Magic value denoting presence of user calibration */ 102 #define JC_CAL_USR_MAGIC_0 0xB2 103 #define JC_CAL_USR_MAGIC_1 0xA1 104 #define JC_CAL_USR_MAGIC_SIZE 2 105 106 /* SPI storage addresses of user calibration data */ 107 #define JC_CAL_USR_LEFT_MAGIC_ADDR 0x8010 108 #define JC_CAL_USR_LEFT_DATA_ADDR 0x8012 109 #define JC_CAL_USR_LEFT_DATA_END 0x801A 110 #define JC_CAL_USR_RIGHT_MAGIC_ADDR 0x801B 111 #define JC_CAL_USR_RIGHT_DATA_ADDR 0x801D 112 #define JC_CAL_STICK_DATA_SIZE \ 113 (JC_CAL_USR_LEFT_DATA_END - JC_CAL_USR_LEFT_DATA_ADDR + 1) 114 115 /* SPI storage addresses of factory calibration data */ 116 #define JC_CAL_FCT_DATA_LEFT_ADDR 0x603d 117 #define JC_CAL_FCT_DATA_RIGHT_ADDR 0x6046 118 119 /* SPI storage addresses of IMU factory calibration data */ 120 #define JC_IMU_CAL_FCT_DATA_ADDR 0x6020 121 #define JC_IMU_CAL_FCT_DATA_END 0x6037 122 #define JC_IMU_CAL_DATA_SIZE \ 123 (JC_IMU_CAL_FCT_DATA_END - JC_IMU_CAL_FCT_DATA_ADDR + 1) 124 /* SPI storage addresses of IMU user calibration data */ 125 #define JC_IMU_CAL_USR_MAGIC_ADDR 0x8026 126 #define JC_IMU_CAL_USR_DATA_ADDR 0x8028 127 128 /* The raw analog joystick values will be mapped in terms of this magnitude */ 129 #define JC_MAX_STICK_MAG 32767 130 #define JC_STICK_FUZZ 250 131 #define JC_STICK_FLAT 500 132 133 /* Hat values for pro controller's d-pad */ 134 #define JC_MAX_DPAD_MAG 1 135 #define JC_DPAD_FUZZ 0 136 #define JC_DPAD_FLAT 0 137 138 /* Under most circumstances IMU reports are pushed every 15ms; use as default */ 139 #define JC_IMU_DFLT_AVG_DELTA_MS 15 140 /* How many samples to sum before calculating average IMU report delta */ 141 #define JC_IMU_SAMPLES_PER_DELTA_AVG 300 142 /* Controls how many dropped IMU packets at once trigger a warning message */ 143 #define JC_IMU_DROPPED_PKT_WARNING 3 144 145 /* 146 * The controller's accelerometer has a sensor resolution of 16bits and is 147 * configured with a range of +-8000 milliGs. Therefore, the resolution can be 148 * calculated thus: (2^16-1)/(8000 * 2) = 4.096 digits per milliG 149 * Resolution per G (rather than per millliG): 4.096 * 1000 = 4096 digits per G 150 * Alternatively: 1/4096 = .0002441 Gs per digit 151 */ 152 #define JC_IMU_MAX_ACCEL_MAG 32767 153 #define JC_IMU_ACCEL_RES_PER_G 4096 154 #define JC_IMU_ACCEL_FUZZ 10 155 #define JC_IMU_ACCEL_FLAT 0 156 157 /* 158 * The controller's gyroscope has a sensor resolution of 16bits and is 159 * configured with a range of +-2000 degrees/second. 160 * Digits per dps: (2^16 -1)/(2000*2) = 16.38375 161 * dps per digit: 16.38375E-1 = .0610 162 * 163 * STMicro recommends in the datasheet to add 15% to the dps/digit. This allows 164 * the full sensitivity range to be saturated without clipping. This yields more 165 * accurate results, so it's the technique this driver uses. 166 * dps per digit (corrected): .0610 * 1.15 = .0702 167 * digits per dps (corrected): .0702E-1 = 14.247 168 * 169 * Now, 14.247 truncating to 14 loses a lot of precision, so we rescale the 170 * min/max range by 1000. 171 */ 172 #define JC_IMU_PREC_RANGE_SCALE 1000 173 /* Note: change mag and res_per_dps if prec_range_scale is ever altered */ 174 #define JC_IMU_MAX_GYRO_MAG 32767000 /* (2^16-1)*1000 */ 175 #define JC_IMU_GYRO_RES_PER_DPS 14247 /* (14.247*1000) */ 176 #define JC_IMU_GYRO_FUZZ 10 177 #define JC_IMU_GYRO_FLAT 0 178 179 /* frequency/amplitude tables for rumble */ 180 struct joycon_rumble_freq_data { 181 u16 high; 182 u8 low; 183 u16 freq; /* Hz*/ 184 }; 185 186 struct joycon_rumble_amp_data { 187 u8 high; 188 u16 low; 189 u16 amp; 190 }; 191 192 #if IS_ENABLED(CONFIG_NINTENDO_FF) 193 /* 194 * These tables are from 195 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering/blob/master/rumble_data_table.md 196 */ 197 static const struct joycon_rumble_freq_data joycon_rumble_frequencies[] = { 198 /* high, low, freq */ 199 { 0x0000, 0x01, 41 }, { 0x0000, 0x02, 42 }, { 0x0000, 0x03, 43 }, 200 { 0x0000, 0x04, 44 }, { 0x0000, 0x05, 45 }, { 0x0000, 0x06, 46 }, 201 { 0x0000, 0x07, 47 }, { 0x0000, 0x08, 48 }, { 0x0000, 0x09, 49 }, 202 { 0x0000, 0x0A, 50 }, { 0x0000, 0x0B, 51 }, { 0x0000, 0x0C, 52 }, 203 { 0x0000, 0x0D, 53 }, { 0x0000, 0x0E, 54 }, { 0x0000, 0x0F, 55 }, 204 { 0x0000, 0x10, 57 }, { 0x0000, 0x11, 58 }, { 0x0000, 0x12, 59 }, 205 { 0x0000, 0x13, 60 }, { 0x0000, 0x14, 62 }, { 0x0000, 0x15, 63 }, 206 { 0x0000, 0x16, 64 }, { 0x0000, 0x17, 66 }, { 0x0000, 0x18, 67 }, 207 { 0x0000, 0x19, 69 }, { 0x0000, 0x1A, 70 }, { 0x0000, 0x1B, 72 }, 208 { 0x0000, 0x1C, 73 }, { 0x0000, 0x1D, 75 }, { 0x0000, 0x1e, 77 }, 209 { 0x0000, 0x1f, 78 }, { 0x0000, 0x20, 80 }, { 0x0400, 0x21, 82 }, 210 { 0x0800, 0x22, 84 }, { 0x0c00, 0x23, 85 }, { 0x1000, 0x24, 87 }, 211 { 0x1400, 0x25, 89 }, { 0x1800, 0x26, 91 }, { 0x1c00, 0x27, 93 }, 212 { 0x2000, 0x28, 95 }, { 0x2400, 0x29, 97 }, { 0x2800, 0x2a, 99 }, 213 { 0x2c00, 0x2b, 102 }, { 0x3000, 0x2c, 104 }, { 0x3400, 0x2d, 106 }, 214 { 0x3800, 0x2e, 108 }, { 0x3c00, 0x2f, 111 }, { 0x4000, 0x30, 113 }, 215 { 0x4400, 0x31, 116 }, { 0x4800, 0x32, 118 }, { 0x4c00, 0x33, 121 }, 216 { 0x5000, 0x34, 123 }, { 0x5400, 0x35, 126 }, { 0x5800, 0x36, 129 }, 217 { 0x5c00, 0x37, 132 }, { 0x6000, 0x38, 135 }, { 0x6400, 0x39, 137 }, 218 { 0x6800, 0x3a, 141 }, { 0x6c00, 0x3b, 144 }, { 0x7000, 0x3c, 147 }, 219 { 0x7400, 0x3d, 150 }, { 0x7800, 0x3e, 153 }, { 0x7c00, 0x3f, 157 }, 220 { 0x8000, 0x40, 160 }, { 0x8400, 0x41, 164 }, { 0x8800, 0x42, 167 }, 221 { 0x8c00, 0x43, 171 }, { 0x9000, 0x44, 174 }, { 0x9400, 0x45, 178 }, 222 { 0x9800, 0x46, 182 }, { 0x9c00, 0x47, 186 }, { 0xa000, 0x48, 190 }, 223 { 0xa400, 0x49, 194 }, { 0xa800, 0x4a, 199 }, { 0xac00, 0x4b, 203 }, 224 { 0xb000, 0x4c, 207 }, { 0xb400, 0x4d, 212 }, { 0xb800, 0x4e, 217 }, 225 { 0xbc00, 0x4f, 221 }, { 0xc000, 0x50, 226 }, { 0xc400, 0x51, 231 }, 226 { 0xc800, 0x52, 236 }, { 0xcc00, 0x53, 241 }, { 0xd000, 0x54, 247 }, 227 { 0xd400, 0x55, 252 }, { 0xd800, 0x56, 258 }, { 0xdc00, 0x57, 263 }, 228 { 0xe000, 0x58, 269 }, { 0xe400, 0x59, 275 }, { 0xe800, 0x5a, 281 }, 229 { 0xec00, 0x5b, 287 }, { 0xf000, 0x5c, 293 }, { 0xf400, 0x5d, 300 }, 230 { 0xf800, 0x5e, 306 }, { 0xfc00, 0x5f, 313 }, { 0x0001, 0x60, 320 }, 231 { 0x0401, 0x61, 327 }, { 0x0801, 0x62, 334 }, { 0x0c01, 0x63, 341 }, 232 { 0x1001, 0x64, 349 }, { 0x1401, 0x65, 357 }, { 0x1801, 0x66, 364 }, 233 { 0x1c01, 0x67, 372 }, { 0x2001, 0x68, 381 }, { 0x2401, 0x69, 389 }, 234 { 0x2801, 0x6a, 397 }, { 0x2c01, 0x6b, 406 }, { 0x3001, 0x6c, 415 }, 235 { 0x3401, 0x6d, 424 }, { 0x3801, 0x6e, 433 }, { 0x3c01, 0x6f, 443 }, 236 { 0x4001, 0x70, 453 }, { 0x4401, 0x71, 462 }, { 0x4801, 0x72, 473 }, 237 { 0x4c01, 0x73, 483 }, { 0x5001, 0x74, 494 }, { 0x5401, 0x75, 504 }, 238 { 0x5801, 0x76, 515 }, { 0x5c01, 0x77, 527 }, { 0x6001, 0x78, 538 }, 239 { 0x6401, 0x79, 550 }, { 0x6801, 0x7a, 562 }, { 0x6c01, 0x7b, 574 }, 240 { 0x7001, 0x7c, 587 }, { 0x7401, 0x7d, 600 }, { 0x7801, 0x7e, 613 }, 241 { 0x7c01, 0x7f, 626 }, { 0x8001, 0x00, 640 }, { 0x8401, 0x00, 654 }, 242 { 0x8801, 0x00, 668 }, { 0x8c01, 0x00, 683 }, { 0x9001, 0x00, 698 }, 243 { 0x9401, 0x00, 713 }, { 0x9801, 0x00, 729 }, { 0x9c01, 0x00, 745 }, 244 { 0xa001, 0x00, 761 }, { 0xa401, 0x00, 778 }, { 0xa801, 0x00, 795 }, 245 { 0xac01, 0x00, 812 }, { 0xb001, 0x00, 830 }, { 0xb401, 0x00, 848 }, 246 { 0xb801, 0x00, 867 }, { 0xbc01, 0x00, 886 }, { 0xc001, 0x00, 905 }, 247 { 0xc401, 0x00, 925 }, { 0xc801, 0x00, 945 }, { 0xcc01, 0x00, 966 }, 248 { 0xd001, 0x00, 987 }, { 0xd401, 0x00, 1009 }, { 0xd801, 0x00, 1031 }, 249 { 0xdc01, 0x00, 1053 }, { 0xe001, 0x00, 1076 }, { 0xe401, 0x00, 1100 }, 250 { 0xe801, 0x00, 1124 }, { 0xec01, 0x00, 1149 }, { 0xf001, 0x00, 1174 }, 251 { 0xf401, 0x00, 1199 }, { 0xf801, 0x00, 1226 }, { 0xfc01, 0x00, 1253 } 252 }; 253 254 #define joycon_max_rumble_amp (1003) 255 static const struct joycon_rumble_amp_data joycon_rumble_amplitudes[] = { 256 /* high, low, amp */ 257 { 0x00, 0x0040, 0 }, 258 { 0x02, 0x8040, 10 }, { 0x04, 0x0041, 12 }, { 0x06, 0x8041, 14 }, 259 { 0x08, 0x0042, 17 }, { 0x0a, 0x8042, 20 }, { 0x0c, 0x0043, 24 }, 260 { 0x0e, 0x8043, 28 }, { 0x10, 0x0044, 33 }, { 0x12, 0x8044, 40 }, 261 { 0x14, 0x0045, 47 }, { 0x16, 0x8045, 56 }, { 0x18, 0x0046, 67 }, 262 { 0x1a, 0x8046, 80 }, { 0x1c, 0x0047, 95 }, { 0x1e, 0x8047, 112 }, 263 { 0x20, 0x0048, 117 }, { 0x22, 0x8048, 123 }, { 0x24, 0x0049, 128 }, 264 { 0x26, 0x8049, 134 }, { 0x28, 0x004a, 140 }, { 0x2a, 0x804a, 146 }, 265 { 0x2c, 0x004b, 152 }, { 0x2e, 0x804b, 159 }, { 0x30, 0x004c, 166 }, 266 { 0x32, 0x804c, 173 }, { 0x34, 0x004d, 181 }, { 0x36, 0x804d, 189 }, 267 { 0x38, 0x004e, 198 }, { 0x3a, 0x804e, 206 }, { 0x3c, 0x004f, 215 }, 268 { 0x3e, 0x804f, 225 }, { 0x40, 0x0050, 230 }, { 0x42, 0x8050, 235 }, 269 { 0x44, 0x0051, 240 }, { 0x46, 0x8051, 245 }, { 0x48, 0x0052, 251 }, 270 { 0x4a, 0x8052, 256 }, { 0x4c, 0x0053, 262 }, { 0x4e, 0x8053, 268 }, 271 { 0x50, 0x0054, 273 }, { 0x52, 0x8054, 279 }, { 0x54, 0x0055, 286 }, 272 { 0x56, 0x8055, 292 }, { 0x58, 0x0056, 298 }, { 0x5a, 0x8056, 305 }, 273 { 0x5c, 0x0057, 311 }, { 0x5e, 0x8057, 318 }, { 0x60, 0x0058, 325 }, 274 { 0x62, 0x8058, 332 }, { 0x64, 0x0059, 340 }, { 0x66, 0x8059, 347 }, 275 { 0x68, 0x005a, 355 }, { 0x6a, 0x805a, 362 }, { 0x6c, 0x005b, 370 }, 276 { 0x6e, 0x805b, 378 }, { 0x70, 0x005c, 387 }, { 0x72, 0x805c, 395 }, 277 { 0x74, 0x005d, 404 }, { 0x76, 0x805d, 413 }, { 0x78, 0x005e, 422 }, 278 { 0x7a, 0x805e, 431 }, { 0x7c, 0x005f, 440 }, { 0x7e, 0x805f, 450 }, 279 { 0x80, 0x0060, 460 }, { 0x82, 0x8060, 470 }, { 0x84, 0x0061, 480 }, 280 { 0x86, 0x8061, 491 }, { 0x88, 0x0062, 501 }, { 0x8a, 0x8062, 512 }, 281 { 0x8c, 0x0063, 524 }, { 0x8e, 0x8063, 535 }, { 0x90, 0x0064, 547 }, 282 { 0x92, 0x8064, 559 }, { 0x94, 0x0065, 571 }, { 0x96, 0x8065, 584 }, 283 { 0x98, 0x0066, 596 }, { 0x9a, 0x8066, 609 }, { 0x9c, 0x0067, 623 }, 284 { 0x9e, 0x8067, 636 }, { 0xa0, 0x0068, 650 }, { 0xa2, 0x8068, 665 }, 285 { 0xa4, 0x0069, 679 }, { 0xa6, 0x8069, 694 }, { 0xa8, 0x006a, 709 }, 286 { 0xaa, 0x806a, 725 }, { 0xac, 0x006b, 741 }, { 0xae, 0x806b, 757 }, 287 { 0xb0, 0x006c, 773 }, { 0xb2, 0x806c, 790 }, { 0xb4, 0x006d, 808 }, 288 { 0xb6, 0x806d, 825 }, { 0xb8, 0x006e, 843 }, { 0xba, 0x806e, 862 }, 289 { 0xbc, 0x006f, 881 }, { 0xbe, 0x806f, 900 }, { 0xc0, 0x0070, 920 }, 290 { 0xc2, 0x8070, 940 }, { 0xc4, 0x0071, 960 }, { 0xc6, 0x8071, 981 }, 291 { 0xc8, 0x0072, joycon_max_rumble_amp } 292 }; 293 static const u16 JC_RUMBLE_DFLT_LOW_FREQ = 160; 294 static const u16 JC_RUMBLE_DFLT_HIGH_FREQ = 320; 295 static const unsigned short JC_RUMBLE_ZERO_AMP_PKT_CNT = 5; 296 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 297 static const u16 JC_RUMBLE_PERIOD_MS = 50; 298 299 /* States for controller state machine */ 300 enum joycon_ctlr_state { 301 JOYCON_CTLR_STATE_INIT, 302 JOYCON_CTLR_STATE_READ, 303 JOYCON_CTLR_STATE_REMOVED, 304 }; 305 306 /* Controller type received as part of device info */ 307 enum joycon_ctlr_type { 308 JOYCON_CTLR_TYPE_JCL = 0x01, 309 JOYCON_CTLR_TYPE_JCR = 0x02, 310 JOYCON_CTLR_TYPE_PRO = 0x03, 311 }; 312 313 struct joycon_stick_cal { 314 s32 max; 315 s32 min; 316 s32 center; 317 }; 318 319 struct joycon_imu_cal { 320 s16 offset[3]; 321 s16 scale[3]; 322 }; 323 324 /* 325 * All the controller's button values are stored in a u32. 326 * They can be accessed with bitwise ANDs. 327 */ 328 static const u32 JC_BTN_Y = BIT(0); 329 static const u32 JC_BTN_X = BIT(1); 330 static const u32 JC_BTN_B = BIT(2); 331 static const u32 JC_BTN_A = BIT(3); 332 static const u32 JC_BTN_SR_R = BIT(4); 333 static const u32 JC_BTN_SL_R = BIT(5); 334 static const u32 JC_BTN_R = BIT(6); 335 static const u32 JC_BTN_ZR = BIT(7); 336 static const u32 JC_BTN_MINUS = BIT(8); 337 static const u32 JC_BTN_PLUS = BIT(9); 338 static const u32 JC_BTN_RSTICK = BIT(10); 339 static const u32 JC_BTN_LSTICK = BIT(11); 340 static const u32 JC_BTN_HOME = BIT(12); 341 static const u32 JC_BTN_CAP = BIT(13); /* capture button */ 342 static const u32 JC_BTN_DOWN = BIT(16); 343 static const u32 JC_BTN_UP = BIT(17); 344 static const u32 JC_BTN_RIGHT = BIT(18); 345 static const u32 JC_BTN_LEFT = BIT(19); 346 static const u32 JC_BTN_SR_L = BIT(20); 347 static const u32 JC_BTN_SL_L = BIT(21); 348 static const u32 JC_BTN_L = BIT(22); 349 static const u32 JC_BTN_ZL = BIT(23); 350 351 enum joycon_msg_type { 352 JOYCON_MSG_TYPE_NONE, 353 JOYCON_MSG_TYPE_USB, 354 JOYCON_MSG_TYPE_SUBCMD, 355 }; 356 357 struct joycon_rumble_output { 358 u8 output_id; 359 u8 packet_num; 360 u8 rumble_data[8]; 361 } __packed; 362 363 struct joycon_subcmd_request { 364 u8 output_id; /* must be 0x01 for subcommand, 0x10 for rumble only */ 365 u8 packet_num; /* incremented every send */ 366 u8 rumble_data[8]; 367 u8 subcmd_id; 368 u8 data[]; /* length depends on the subcommand */ 369 } __packed; 370 371 struct joycon_subcmd_reply { 372 u8 ack; /* MSB 1 for ACK, 0 for NACK */ 373 u8 id; /* id of requested subcmd */ 374 u8 data[]; /* will be at most 35 bytes */ 375 } __packed; 376 377 struct joycon_imu_data { 378 s16 accel_x; 379 s16 accel_y; 380 s16 accel_z; 381 s16 gyro_x; 382 s16 gyro_y; 383 s16 gyro_z; 384 } __packed; 385 386 struct joycon_input_report { 387 u8 id; 388 u8 timer; 389 u8 bat_con; /* battery and connection info */ 390 u8 button_status[3]; 391 u8 left_stick[3]; 392 u8 right_stick[3]; 393 u8 vibrator_report; 394 395 union { 396 struct joycon_subcmd_reply subcmd_reply; 397 /* IMU input reports contain 3 samples */ 398 u8 imu_raw_bytes[sizeof(struct joycon_imu_data) * 3]; 399 }; 400 } __packed; 401 402 #define JC_MAX_RESP_SIZE (sizeof(struct joycon_input_report) + 35) 403 #define JC_RUMBLE_DATA_SIZE 8 404 #define JC_RUMBLE_QUEUE_SIZE 8 405 406 static const char * const joycon_player_led_names[] = { 407 LED_FUNCTION_PLAYER1, 408 LED_FUNCTION_PLAYER2, 409 LED_FUNCTION_PLAYER3, 410 LED_FUNCTION_PLAYER4, 411 }; 412 #define JC_NUM_LEDS ARRAY_SIZE(joycon_player_led_names) 413 414 /* Each physical controller is associated with a joycon_ctlr struct */ 415 struct joycon_ctlr { 416 struct hid_device *hdev; 417 struct input_dev *input; 418 struct led_classdev leds[JC_NUM_LEDS]; /* player leds */ 419 struct led_classdev home_led; 420 enum joycon_ctlr_state ctlr_state; 421 spinlock_t lock; 422 u8 mac_addr[6]; 423 char *mac_addr_str; 424 enum joycon_ctlr_type ctlr_type; 425 426 /* The following members are used for synchronous sends/receives */ 427 enum joycon_msg_type msg_type; 428 u8 subcmd_num; 429 struct mutex output_mutex; 430 u8 input_buf[JC_MAX_RESP_SIZE]; 431 wait_queue_head_t wait; 432 bool received_resp; 433 u8 usb_ack_match; 434 u8 subcmd_ack_match; 435 bool received_input_report; 436 unsigned int last_subcmd_sent_msecs; 437 438 /* factory calibration data */ 439 struct joycon_stick_cal left_stick_cal_x; 440 struct joycon_stick_cal left_stick_cal_y; 441 struct joycon_stick_cal right_stick_cal_x; 442 struct joycon_stick_cal right_stick_cal_y; 443 444 struct joycon_imu_cal accel_cal; 445 struct joycon_imu_cal gyro_cal; 446 447 /* prevents needlessly recalculating these divisors every sample */ 448 s32 imu_cal_accel_divisor[3]; 449 s32 imu_cal_gyro_divisor[3]; 450 451 /* power supply data */ 452 struct power_supply *battery; 453 struct power_supply_desc battery_desc; 454 u8 battery_capacity; 455 bool battery_charging; 456 bool host_powered; 457 458 /* rumble */ 459 u8 rumble_data[JC_RUMBLE_QUEUE_SIZE][JC_RUMBLE_DATA_SIZE]; 460 int rumble_queue_head; 461 int rumble_queue_tail; 462 struct workqueue_struct *rumble_queue; 463 struct work_struct rumble_worker; 464 unsigned int rumble_msecs; 465 u16 rumble_ll_freq; 466 u16 rumble_lh_freq; 467 u16 rumble_rl_freq; 468 u16 rumble_rh_freq; 469 unsigned short rumble_zero_countdown; 470 471 /* imu */ 472 struct input_dev *imu_input; 473 bool imu_first_packet_received; /* helps in initiating timestamp */ 474 unsigned int imu_timestamp_us; /* timestamp we report to userspace */ 475 unsigned int imu_last_pkt_ms; /* used to calc imu report delta */ 476 /* the following are used to track the average imu report time delta */ 477 unsigned int imu_delta_samples_count; 478 unsigned int imu_delta_samples_sum; 479 unsigned int imu_avg_delta_ms; 480 }; 481 482 /* Helper macros for checking controller type */ 483 #define jc_type_is_joycon(ctlr) \ 484 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL || \ 485 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR || \ 486 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 487 #define jc_type_is_procon(ctlr) \ 488 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_PROCON) 489 #define jc_type_is_chrggrip(ctlr) \ 490 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 491 492 /* Does this controller have inputs associated with left joycon? */ 493 #define jc_type_has_left(ctlr) \ 494 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL || \ 495 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 496 497 /* Does this controller have inputs associated with right joycon? */ 498 #define jc_type_has_right(ctlr) \ 499 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR || \ 500 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 501 502 static int __joycon_hid_send(struct hid_device *hdev, u8 *data, size_t len) 503 { 504 u8 *buf; 505 int ret; 506 507 buf = kmemdup(data, len, GFP_KERNEL); 508 if (!buf) 509 return -ENOMEM; 510 ret = hid_hw_output_report(hdev, buf, len); 511 kfree(buf); 512 if (ret < 0) 513 hid_dbg(hdev, "Failed to send output report ret=%d\n", ret); 514 return ret; 515 } 516 517 static void joycon_wait_for_input_report(struct joycon_ctlr *ctlr) 518 { 519 int ret; 520 521 /* 522 * If we are in the proper reporting mode, wait for an input 523 * report prior to sending the subcommand. This improves 524 * reliability considerably. 525 */ 526 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) { 527 unsigned long flags; 528 529 spin_lock_irqsave(&ctlr->lock, flags); 530 ctlr->received_input_report = false; 531 spin_unlock_irqrestore(&ctlr->lock, flags); 532 ret = wait_event_timeout(ctlr->wait, 533 ctlr->received_input_report, 534 HZ / 4); 535 /* We will still proceed, even with a timeout here */ 536 if (!ret) 537 hid_warn(ctlr->hdev, 538 "timeout waiting for input report\n"); 539 } 540 } 541 542 /* 543 * Sending subcommands and/or rumble data at too high a rate can cause bluetooth 544 * controller disconnections. 545 */ 546 static void joycon_enforce_subcmd_rate(struct joycon_ctlr *ctlr) 547 { 548 static const unsigned int max_subcmd_rate_ms = 25; 549 unsigned int current_ms = jiffies_to_msecs(jiffies); 550 unsigned int delta_ms = current_ms - ctlr->last_subcmd_sent_msecs; 551 552 while (delta_ms < max_subcmd_rate_ms && 553 ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) { 554 joycon_wait_for_input_report(ctlr); 555 current_ms = jiffies_to_msecs(jiffies); 556 delta_ms = current_ms - ctlr->last_subcmd_sent_msecs; 557 } 558 ctlr->last_subcmd_sent_msecs = current_ms; 559 } 560 561 static int joycon_hid_send_sync(struct joycon_ctlr *ctlr, u8 *data, size_t len, 562 u32 timeout) 563 { 564 int ret; 565 int tries = 2; 566 567 /* 568 * The controller occasionally seems to drop subcommands. In testing, 569 * doing one retry after a timeout appears to always work. 570 */ 571 while (tries--) { 572 joycon_enforce_subcmd_rate(ctlr); 573 574 ret = __joycon_hid_send(ctlr->hdev, data, len); 575 if (ret < 0) { 576 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 577 return ret; 578 } 579 580 ret = wait_event_timeout(ctlr->wait, ctlr->received_resp, 581 timeout); 582 if (!ret) { 583 hid_dbg(ctlr->hdev, 584 "synchronous send/receive timed out\n"); 585 if (tries) { 586 hid_dbg(ctlr->hdev, 587 "retrying sync send after timeout\n"); 588 } 589 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 590 ret = -ETIMEDOUT; 591 } else { 592 ret = 0; 593 break; 594 } 595 } 596 597 ctlr->received_resp = false; 598 return ret; 599 } 600 601 static int joycon_send_usb(struct joycon_ctlr *ctlr, u8 cmd, u32 timeout) 602 { 603 int ret; 604 u8 buf[2] = {JC_OUTPUT_USB_CMD}; 605 606 buf[1] = cmd; 607 ctlr->usb_ack_match = cmd; 608 ctlr->msg_type = JOYCON_MSG_TYPE_USB; 609 ret = joycon_hid_send_sync(ctlr, buf, sizeof(buf), timeout); 610 if (ret) 611 hid_dbg(ctlr->hdev, "send usb command failed; ret=%d\n", ret); 612 return ret; 613 } 614 615 static int joycon_send_subcmd(struct joycon_ctlr *ctlr, 616 struct joycon_subcmd_request *subcmd, 617 size_t data_len, u32 timeout) 618 { 619 int ret; 620 unsigned long flags; 621 622 spin_lock_irqsave(&ctlr->lock, flags); 623 /* 624 * If the controller has been removed, just return ENODEV so the LED 625 * subsystem doesn't print invalid errors on removal. 626 */ 627 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 628 spin_unlock_irqrestore(&ctlr->lock, flags); 629 return -ENODEV; 630 } 631 memcpy(subcmd->rumble_data, ctlr->rumble_data[ctlr->rumble_queue_tail], 632 JC_RUMBLE_DATA_SIZE); 633 spin_unlock_irqrestore(&ctlr->lock, flags); 634 635 subcmd->output_id = JC_OUTPUT_RUMBLE_AND_SUBCMD; 636 subcmd->packet_num = ctlr->subcmd_num; 637 if (++ctlr->subcmd_num > 0xF) 638 ctlr->subcmd_num = 0; 639 ctlr->subcmd_ack_match = subcmd->subcmd_id; 640 ctlr->msg_type = JOYCON_MSG_TYPE_SUBCMD; 641 642 ret = joycon_hid_send_sync(ctlr, (u8 *)subcmd, 643 sizeof(*subcmd) + data_len, timeout); 644 if (ret < 0) 645 hid_dbg(ctlr->hdev, "send subcommand failed; ret=%d\n", ret); 646 else 647 ret = 0; 648 return ret; 649 } 650 651 /* Supply nibbles for flash and on. Ones correspond to active */ 652 static int joycon_set_player_leds(struct joycon_ctlr *ctlr, u8 flash, u8 on) 653 { 654 struct joycon_subcmd_request *req; 655 u8 buffer[sizeof(*req) + 1] = { 0 }; 656 657 req = (struct joycon_subcmd_request *)buffer; 658 req->subcmd_id = JC_SUBCMD_SET_PLAYER_LIGHTS; 659 req->data[0] = (flash << 4) | on; 660 661 hid_dbg(ctlr->hdev, "setting player leds\n"); 662 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 663 } 664 665 static int joycon_request_spi_flash_read(struct joycon_ctlr *ctlr, 666 u32 start_addr, u8 size, u8 **reply) 667 { 668 struct joycon_subcmd_request *req; 669 struct joycon_input_report *report; 670 u8 buffer[sizeof(*req) + 5] = { 0 }; 671 u8 *data; 672 int ret; 673 674 if (!reply) 675 return -EINVAL; 676 677 req = (struct joycon_subcmd_request *)buffer; 678 req->subcmd_id = JC_SUBCMD_SPI_FLASH_READ; 679 data = req->data; 680 put_unaligned_le32(start_addr, data); 681 data[4] = size; 682 683 hid_dbg(ctlr->hdev, "requesting SPI flash data\n"); 684 ret = joycon_send_subcmd(ctlr, req, 5, HZ); 685 if (ret) { 686 hid_err(ctlr->hdev, "failed reading SPI flash; ret=%d\n", ret); 687 } else { 688 report = (struct joycon_input_report *)ctlr->input_buf; 689 /* The read data starts at the 6th byte */ 690 *reply = &report->subcmd_reply.data[5]; 691 } 692 return ret; 693 } 694 695 /* 696 * User calibration's presence is denoted with a magic byte preceding it. 697 * returns 0 if magic val is present, 1 if not present, < 0 on error 698 */ 699 static int joycon_check_for_cal_magic(struct joycon_ctlr *ctlr, u32 flash_addr) 700 { 701 int ret; 702 u8 *reply; 703 704 ret = joycon_request_spi_flash_read(ctlr, flash_addr, 705 JC_CAL_USR_MAGIC_SIZE, &reply); 706 if (ret) 707 return ret; 708 709 return reply[0] != JC_CAL_USR_MAGIC_0 || reply[1] != JC_CAL_USR_MAGIC_1; 710 } 711 712 static int joycon_read_stick_calibration(struct joycon_ctlr *ctlr, u16 cal_addr, 713 struct joycon_stick_cal *cal_x, 714 struct joycon_stick_cal *cal_y, 715 bool left_stick) 716 { 717 s32 x_max_above; 718 s32 x_min_below; 719 s32 y_max_above; 720 s32 y_min_below; 721 u8 *raw_cal; 722 int ret; 723 724 ret = joycon_request_spi_flash_read(ctlr, cal_addr, 725 JC_CAL_STICK_DATA_SIZE, &raw_cal); 726 if (ret) 727 return ret; 728 729 /* stick calibration parsing: note the order differs based on stick */ 730 if (left_stick) { 731 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 732 12); 733 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 734 12); 735 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 736 12); 737 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 738 12); 739 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 740 12); 741 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 742 12); 743 } else { 744 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 745 12); 746 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 747 12); 748 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 749 12); 750 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 751 12); 752 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 753 12); 754 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 755 12); 756 } 757 758 cal_x->max = cal_x->center + x_max_above; 759 cal_x->min = cal_x->center - x_min_below; 760 cal_y->max = cal_y->center + y_max_above; 761 cal_y->min = cal_y->center - y_min_below; 762 763 return 0; 764 } 765 766 static const u16 DFLT_STICK_CAL_CEN = 2000; 767 static const u16 DFLT_STICK_CAL_MAX = 3500; 768 static const u16 DFLT_STICK_CAL_MIN = 500; 769 static int joycon_request_calibration(struct joycon_ctlr *ctlr) 770 { 771 u16 left_stick_addr = JC_CAL_FCT_DATA_LEFT_ADDR; 772 u16 right_stick_addr = JC_CAL_FCT_DATA_RIGHT_ADDR; 773 int ret; 774 775 hid_dbg(ctlr->hdev, "requesting cal data\n"); 776 777 /* check if user stick calibrations are present */ 778 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_LEFT_MAGIC_ADDR)) { 779 left_stick_addr = JC_CAL_USR_LEFT_DATA_ADDR; 780 hid_info(ctlr->hdev, "using user cal for left stick\n"); 781 } else { 782 hid_info(ctlr->hdev, "using factory cal for left stick\n"); 783 } 784 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_RIGHT_MAGIC_ADDR)) { 785 right_stick_addr = JC_CAL_USR_RIGHT_DATA_ADDR; 786 hid_info(ctlr->hdev, "using user cal for right stick\n"); 787 } else { 788 hid_info(ctlr->hdev, "using factory cal for right stick\n"); 789 } 790 791 /* read the left stick calibration data */ 792 ret = joycon_read_stick_calibration(ctlr, left_stick_addr, 793 &ctlr->left_stick_cal_x, 794 &ctlr->left_stick_cal_y, 795 true); 796 if (ret) { 797 hid_warn(ctlr->hdev, 798 "Failed to read left stick cal, using dflts; e=%d\n", 799 ret); 800 801 ctlr->left_stick_cal_x.center = DFLT_STICK_CAL_CEN; 802 ctlr->left_stick_cal_x.max = DFLT_STICK_CAL_MAX; 803 ctlr->left_stick_cal_x.min = DFLT_STICK_CAL_MIN; 804 805 ctlr->left_stick_cal_y.center = DFLT_STICK_CAL_CEN; 806 ctlr->left_stick_cal_y.max = DFLT_STICK_CAL_MAX; 807 ctlr->left_stick_cal_y.min = DFLT_STICK_CAL_MIN; 808 } 809 810 /* read the right stick calibration data */ 811 ret = joycon_read_stick_calibration(ctlr, right_stick_addr, 812 &ctlr->right_stick_cal_x, 813 &ctlr->right_stick_cal_y, 814 false); 815 if (ret) { 816 hid_warn(ctlr->hdev, 817 "Failed to read right stick cal, using dflts; e=%d\n", 818 ret); 819 820 ctlr->right_stick_cal_x.center = DFLT_STICK_CAL_CEN; 821 ctlr->right_stick_cal_x.max = DFLT_STICK_CAL_MAX; 822 ctlr->right_stick_cal_x.min = DFLT_STICK_CAL_MIN; 823 824 ctlr->right_stick_cal_y.center = DFLT_STICK_CAL_CEN; 825 ctlr->right_stick_cal_y.max = DFLT_STICK_CAL_MAX; 826 ctlr->right_stick_cal_y.min = DFLT_STICK_CAL_MIN; 827 } 828 829 hid_dbg(ctlr->hdev, "calibration:\n" 830 "l_x_c=%d l_x_max=%d l_x_min=%d\n" 831 "l_y_c=%d l_y_max=%d l_y_min=%d\n" 832 "r_x_c=%d r_x_max=%d r_x_min=%d\n" 833 "r_y_c=%d r_y_max=%d r_y_min=%d\n", 834 ctlr->left_stick_cal_x.center, 835 ctlr->left_stick_cal_x.max, 836 ctlr->left_stick_cal_x.min, 837 ctlr->left_stick_cal_y.center, 838 ctlr->left_stick_cal_y.max, 839 ctlr->left_stick_cal_y.min, 840 ctlr->right_stick_cal_x.center, 841 ctlr->right_stick_cal_x.max, 842 ctlr->right_stick_cal_x.min, 843 ctlr->right_stick_cal_y.center, 844 ctlr->right_stick_cal_y.max, 845 ctlr->right_stick_cal_y.min); 846 847 return 0; 848 } 849 850 /* 851 * These divisors are calculated once rather than for each sample. They are only 852 * dependent on the IMU calibration values. They are used when processing the 853 * IMU input reports. 854 */ 855 static void joycon_calc_imu_cal_divisors(struct joycon_ctlr *ctlr) 856 { 857 int i; 858 859 for (i = 0; i < 3; i++) { 860 ctlr->imu_cal_accel_divisor[i] = ctlr->accel_cal.scale[i] - 861 ctlr->accel_cal.offset[i]; 862 ctlr->imu_cal_gyro_divisor[i] = ctlr->gyro_cal.scale[i] - 863 ctlr->gyro_cal.offset[i]; 864 } 865 } 866 867 static const s16 DFLT_ACCEL_OFFSET /*= 0*/; 868 static const s16 DFLT_ACCEL_SCALE = 16384; 869 static const s16 DFLT_GYRO_OFFSET /*= 0*/; 870 static const s16 DFLT_GYRO_SCALE = 13371; 871 static int joycon_request_imu_calibration(struct joycon_ctlr *ctlr) 872 { 873 u16 imu_cal_addr = JC_IMU_CAL_FCT_DATA_ADDR; 874 u8 *raw_cal; 875 int ret; 876 int i; 877 878 /* check if user calibration exists */ 879 if (!joycon_check_for_cal_magic(ctlr, JC_IMU_CAL_USR_MAGIC_ADDR)) { 880 imu_cal_addr = JC_IMU_CAL_USR_DATA_ADDR; 881 hid_info(ctlr->hdev, "using user cal for IMU\n"); 882 } else { 883 hid_info(ctlr->hdev, "using factory cal for IMU\n"); 884 } 885 886 /* request IMU calibration data */ 887 hid_dbg(ctlr->hdev, "requesting IMU cal data\n"); 888 ret = joycon_request_spi_flash_read(ctlr, imu_cal_addr, 889 JC_IMU_CAL_DATA_SIZE, &raw_cal); 890 if (ret) { 891 hid_warn(ctlr->hdev, 892 "Failed to read IMU cal, using defaults; ret=%d\n", 893 ret); 894 895 for (i = 0; i < 3; i++) { 896 ctlr->accel_cal.offset[i] = DFLT_ACCEL_OFFSET; 897 ctlr->accel_cal.scale[i] = DFLT_ACCEL_SCALE; 898 ctlr->gyro_cal.offset[i] = DFLT_GYRO_OFFSET; 899 ctlr->gyro_cal.scale[i] = DFLT_GYRO_SCALE; 900 } 901 joycon_calc_imu_cal_divisors(ctlr); 902 return ret; 903 } 904 905 /* IMU calibration parsing */ 906 for (i = 0; i < 3; i++) { 907 int j = i * 2; 908 909 ctlr->accel_cal.offset[i] = get_unaligned_le16(raw_cal + j); 910 ctlr->accel_cal.scale[i] = get_unaligned_le16(raw_cal + j + 6); 911 ctlr->gyro_cal.offset[i] = get_unaligned_le16(raw_cal + j + 12); 912 ctlr->gyro_cal.scale[i] = get_unaligned_le16(raw_cal + j + 18); 913 } 914 915 joycon_calc_imu_cal_divisors(ctlr); 916 917 hid_dbg(ctlr->hdev, "IMU calibration:\n" 918 "a_o[0]=%d a_o[1]=%d a_o[2]=%d\n" 919 "a_s[0]=%d a_s[1]=%d a_s[2]=%d\n" 920 "g_o[0]=%d g_o[1]=%d g_o[2]=%d\n" 921 "g_s[0]=%d g_s[1]=%d g_s[2]=%d\n", 922 ctlr->accel_cal.offset[0], 923 ctlr->accel_cal.offset[1], 924 ctlr->accel_cal.offset[2], 925 ctlr->accel_cal.scale[0], 926 ctlr->accel_cal.scale[1], 927 ctlr->accel_cal.scale[2], 928 ctlr->gyro_cal.offset[0], 929 ctlr->gyro_cal.offset[1], 930 ctlr->gyro_cal.offset[2], 931 ctlr->gyro_cal.scale[0], 932 ctlr->gyro_cal.scale[1], 933 ctlr->gyro_cal.scale[2]); 934 935 return 0; 936 } 937 938 static int joycon_set_report_mode(struct joycon_ctlr *ctlr) 939 { 940 struct joycon_subcmd_request *req; 941 u8 buffer[sizeof(*req) + 1] = { 0 }; 942 943 req = (struct joycon_subcmd_request *)buffer; 944 req->subcmd_id = JC_SUBCMD_SET_REPORT_MODE; 945 req->data[0] = 0x30; /* standard, full report mode */ 946 947 hid_dbg(ctlr->hdev, "setting controller report mode\n"); 948 return joycon_send_subcmd(ctlr, req, 1, HZ); 949 } 950 951 static int joycon_enable_rumble(struct joycon_ctlr *ctlr) 952 { 953 struct joycon_subcmd_request *req; 954 u8 buffer[sizeof(*req) + 1] = { 0 }; 955 956 req = (struct joycon_subcmd_request *)buffer; 957 req->subcmd_id = JC_SUBCMD_ENABLE_VIBRATION; 958 req->data[0] = 0x01; /* note: 0x00 would disable */ 959 960 hid_dbg(ctlr->hdev, "enabling rumble\n"); 961 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 962 } 963 964 static int joycon_enable_imu(struct joycon_ctlr *ctlr) 965 { 966 struct joycon_subcmd_request *req; 967 u8 buffer[sizeof(*req) + 1] = { 0 }; 968 969 req = (struct joycon_subcmd_request *)buffer; 970 req->subcmd_id = JC_SUBCMD_ENABLE_IMU; 971 req->data[0] = 0x01; /* note: 0x00 would disable */ 972 973 hid_dbg(ctlr->hdev, "enabling IMU\n"); 974 return joycon_send_subcmd(ctlr, req, 1, HZ); 975 } 976 977 static s32 joycon_map_stick_val(struct joycon_stick_cal *cal, s32 val) 978 { 979 s32 center = cal->center; 980 s32 min = cal->min; 981 s32 max = cal->max; 982 s32 new_val; 983 984 if (val > center) { 985 new_val = (val - center) * JC_MAX_STICK_MAG; 986 new_val /= (max - center); 987 } else { 988 new_val = (center - val) * -JC_MAX_STICK_MAG; 989 new_val /= (center - min); 990 } 991 new_val = clamp(new_val, (s32)-JC_MAX_STICK_MAG, (s32)JC_MAX_STICK_MAG); 992 return new_val; 993 } 994 995 static void joycon_input_report_parse_imu_data(struct joycon_ctlr *ctlr, 996 struct joycon_input_report *rep, 997 struct joycon_imu_data *imu_data) 998 { 999 u8 *raw = rep->imu_raw_bytes; 1000 int i; 1001 1002 for (i = 0; i < 3; i++) { 1003 struct joycon_imu_data *data = &imu_data[i]; 1004 1005 data->accel_x = get_unaligned_le16(raw + 0); 1006 data->accel_y = get_unaligned_le16(raw + 2); 1007 data->accel_z = get_unaligned_le16(raw + 4); 1008 data->gyro_x = get_unaligned_le16(raw + 6); 1009 data->gyro_y = get_unaligned_le16(raw + 8); 1010 data->gyro_z = get_unaligned_le16(raw + 10); 1011 /* point to next imu sample */ 1012 raw += sizeof(struct joycon_imu_data); 1013 } 1014 } 1015 1016 static void joycon_parse_imu_report(struct joycon_ctlr *ctlr, 1017 struct joycon_input_report *rep) 1018 { 1019 struct joycon_imu_data imu_data[3] = {0}; /* 3 reports per packet */ 1020 struct input_dev *idev = ctlr->imu_input; 1021 unsigned int msecs = jiffies_to_msecs(jiffies); 1022 unsigned int last_msecs = ctlr->imu_last_pkt_ms; 1023 int i; 1024 int value[6]; 1025 1026 joycon_input_report_parse_imu_data(ctlr, rep, imu_data); 1027 1028 /* 1029 * There are complexities surrounding how we determine the timestamps we 1030 * associate with the samples we pass to userspace. The IMU input 1031 * reports do not provide us with a good timestamp. There's a quickly 1032 * incrementing 8-bit counter per input report, but it is not very 1033 * useful for this purpose (it is not entirely clear what rate it 1034 * increments at or if it varies based on packet push rate - more on 1035 * the push rate below...). 1036 * 1037 * The reverse engineering work done on the joy-cons and pro controllers 1038 * by the community seems to indicate the following: 1039 * - The controller samples the IMU every 1.35ms. It then does some of 1040 * its own processing, probably averaging the samples out. 1041 * - Each imu input report contains 3 IMU samples, (usually 5ms apart). 1042 * - In the standard reporting mode (which this driver uses exclusively) 1043 * input reports are pushed from the controller as follows: 1044 * * joy-con (bluetooth): every 15 ms 1045 * * joy-cons (in charging grip via USB): every 15 ms 1046 * * pro controller (USB): every 15 ms 1047 * * pro controller (bluetooth): every 8 ms (this is the wildcard) 1048 * 1049 * Further complicating matters is that some bluetooth stacks are known 1050 * to alter the controller's packet rate by hardcoding the bluetooth 1051 * SSR for the switch controllers (android's stack currently sets the 1052 * SSR to 11ms for both the joy-cons and pro controllers). 1053 * 1054 * In my own testing, I've discovered that my pro controller either 1055 * reports IMU sample batches every 11ms or every 15ms. This rate is 1056 * stable after connecting. It isn't 100% clear what determines this 1057 * rate. Importantly, even when sending every 11ms, none of the samples 1058 * are duplicates. This seems to indicate that the time deltas between 1059 * reported samples can vary based on the input report rate. 1060 * 1061 * The solution employed in this driver is to keep track of the average 1062 * time delta between IMU input reports. In testing, this value has 1063 * proven to be stable, staying at 15ms or 11ms, though other hardware 1064 * configurations and bluetooth stacks could potentially see other rates 1065 * (hopefully this will become more clear as more people use the 1066 * driver). 1067 * 1068 * Keeping track of the average report delta allows us to submit our 1069 * timestamps to userspace based on that. Each report contains 3 1070 * samples, so the IMU sampling rate should be avg_time_delta/3. We can 1071 * also use this average to detect events where we have dropped a 1072 * packet. The userspace timestamp for the samples will be adjusted 1073 * accordingly to prevent unwanted behvaior. 1074 */ 1075 if (!ctlr->imu_first_packet_received) { 1076 ctlr->imu_timestamp_us = 0; 1077 ctlr->imu_delta_samples_count = 0; 1078 ctlr->imu_delta_samples_sum = 0; 1079 ctlr->imu_avg_delta_ms = JC_IMU_DFLT_AVG_DELTA_MS; 1080 ctlr->imu_first_packet_received = true; 1081 } else { 1082 unsigned int delta = msecs - last_msecs; 1083 unsigned int dropped_pkts; 1084 unsigned int dropped_threshold; 1085 1086 /* avg imu report delta housekeeping */ 1087 ctlr->imu_delta_samples_sum += delta; 1088 ctlr->imu_delta_samples_count++; 1089 if (ctlr->imu_delta_samples_count >= 1090 JC_IMU_SAMPLES_PER_DELTA_AVG) { 1091 ctlr->imu_avg_delta_ms = ctlr->imu_delta_samples_sum / 1092 ctlr->imu_delta_samples_count; 1093 /* don't ever want divide by zero shenanigans */ 1094 if (ctlr->imu_avg_delta_ms == 0) { 1095 ctlr->imu_avg_delta_ms = 1; 1096 hid_warn(ctlr->hdev, 1097 "calculated avg imu delta of 0\n"); 1098 } 1099 ctlr->imu_delta_samples_count = 0; 1100 ctlr->imu_delta_samples_sum = 0; 1101 } 1102 1103 /* useful for debugging IMU sample rate */ 1104 hid_dbg(ctlr->hdev, 1105 "imu_report: ms=%u last_ms=%u delta=%u avg_delta=%u\n", 1106 msecs, last_msecs, delta, ctlr->imu_avg_delta_ms); 1107 1108 /* check if any packets have been dropped */ 1109 dropped_threshold = ctlr->imu_avg_delta_ms * 3 / 2; 1110 dropped_pkts = (delta - min(delta, dropped_threshold)) / 1111 ctlr->imu_avg_delta_ms; 1112 ctlr->imu_timestamp_us += 1000 * ctlr->imu_avg_delta_ms; 1113 if (dropped_pkts > JC_IMU_DROPPED_PKT_WARNING) { 1114 hid_warn(ctlr->hdev, 1115 "compensating for %u dropped IMU reports\n", 1116 dropped_pkts); 1117 hid_warn(ctlr->hdev, 1118 "delta=%u avg_delta=%u\n", 1119 delta, ctlr->imu_avg_delta_ms); 1120 } 1121 } 1122 ctlr->imu_last_pkt_ms = msecs; 1123 1124 /* Each IMU input report contains three samples */ 1125 for (i = 0; i < 3; i++) { 1126 input_event(idev, EV_MSC, MSC_TIMESTAMP, 1127 ctlr->imu_timestamp_us); 1128 1129 /* 1130 * These calculations (which use the controller's calibration 1131 * settings to improve the final values) are based on those 1132 * found in the community's reverse-engineering repo (linked at 1133 * top of driver). For hid-nintendo, we make sure that the final 1134 * value given to userspace is always in terms of the axis 1135 * resolution we provided. 1136 * 1137 * Currently only the gyro calculations subtract the calibration 1138 * offsets from the raw value itself. In testing, doing the same 1139 * for the accelerometer raw values decreased accuracy. 1140 * 1141 * Note that the gyro values are multiplied by the 1142 * precision-saving scaling factor to prevent large inaccuracies 1143 * due to truncation of the resolution value which would 1144 * otherwise occur. To prevent overflow (without resorting to 64 1145 * bit integer math), the mult_frac macro is used. 1146 */ 1147 value[0] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1148 (imu_data[i].gyro_x - 1149 ctlr->gyro_cal.offset[0])), 1150 ctlr->gyro_cal.scale[0], 1151 ctlr->imu_cal_gyro_divisor[0]); 1152 value[1] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1153 (imu_data[i].gyro_y - 1154 ctlr->gyro_cal.offset[1])), 1155 ctlr->gyro_cal.scale[1], 1156 ctlr->imu_cal_gyro_divisor[1]); 1157 value[2] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1158 (imu_data[i].gyro_z - 1159 ctlr->gyro_cal.offset[2])), 1160 ctlr->gyro_cal.scale[2], 1161 ctlr->imu_cal_gyro_divisor[2]); 1162 1163 value[3] = ((s32)imu_data[i].accel_x * 1164 ctlr->accel_cal.scale[0]) / 1165 ctlr->imu_cal_accel_divisor[0]; 1166 value[4] = ((s32)imu_data[i].accel_y * 1167 ctlr->accel_cal.scale[1]) / 1168 ctlr->imu_cal_accel_divisor[1]; 1169 value[5] = ((s32)imu_data[i].accel_z * 1170 ctlr->accel_cal.scale[2]) / 1171 ctlr->imu_cal_accel_divisor[2]; 1172 1173 hid_dbg(ctlr->hdev, "raw_gyro: g_x=%d g_y=%d g_z=%d\n", 1174 imu_data[i].gyro_x, imu_data[i].gyro_y, 1175 imu_data[i].gyro_z); 1176 hid_dbg(ctlr->hdev, "raw_accel: a_x=%d a_y=%d a_z=%d\n", 1177 imu_data[i].accel_x, imu_data[i].accel_y, 1178 imu_data[i].accel_z); 1179 1180 /* 1181 * The right joy-con has 2 axes negated, Y and Z. This is due to 1182 * the orientation of the IMU in the controller. We negate those 1183 * axes' values in order to be consistent with the left joy-con 1184 * and the pro controller: 1185 * X: positive is pointing toward the triggers 1186 * Y: positive is pointing to the left 1187 * Z: positive is pointing up (out of the buttons/sticks) 1188 * The axes follow the right-hand rule. 1189 */ 1190 if (jc_type_is_joycon(ctlr) && jc_type_has_right(ctlr)) { 1191 int j; 1192 1193 /* negate all but x axis */ 1194 for (j = 1; j < 6; ++j) { 1195 if (j == 3) 1196 continue; 1197 value[j] *= -1; 1198 } 1199 } 1200 1201 input_report_abs(idev, ABS_RX, value[0]); 1202 input_report_abs(idev, ABS_RY, value[1]); 1203 input_report_abs(idev, ABS_RZ, value[2]); 1204 input_report_abs(idev, ABS_X, value[3]); 1205 input_report_abs(idev, ABS_Y, value[4]); 1206 input_report_abs(idev, ABS_Z, value[5]); 1207 input_sync(idev); 1208 /* convert to micros and divide by 3 (3 samples per report). */ 1209 ctlr->imu_timestamp_us += ctlr->imu_avg_delta_ms * 1000 / 3; 1210 } 1211 } 1212 1213 static void joycon_parse_report(struct joycon_ctlr *ctlr, 1214 struct joycon_input_report *rep) 1215 { 1216 struct input_dev *dev = ctlr->input; 1217 unsigned long flags; 1218 u8 tmp; 1219 u32 btns; 1220 unsigned long msecs = jiffies_to_msecs(jiffies); 1221 1222 spin_lock_irqsave(&ctlr->lock, flags); 1223 if (IS_ENABLED(CONFIG_NINTENDO_FF) && rep->vibrator_report && 1224 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED && 1225 (msecs - ctlr->rumble_msecs) >= JC_RUMBLE_PERIOD_MS && 1226 (ctlr->rumble_queue_head != ctlr->rumble_queue_tail || 1227 ctlr->rumble_zero_countdown > 0)) { 1228 /* 1229 * When this value reaches 0, we know we've sent multiple 1230 * packets to the controller instructing it to disable rumble. 1231 * We can safely stop sending periodic rumble packets until the 1232 * next ff effect. 1233 */ 1234 if (ctlr->rumble_zero_countdown > 0) 1235 ctlr->rumble_zero_countdown--; 1236 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1237 } 1238 1239 /* Parse the battery status */ 1240 tmp = rep->bat_con; 1241 ctlr->host_powered = tmp & BIT(0); 1242 ctlr->battery_charging = tmp & BIT(4); 1243 tmp = tmp >> 5; 1244 switch (tmp) { 1245 case 0: /* empty */ 1246 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; 1247 break; 1248 case 1: /* low */ 1249 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_LOW; 1250 break; 1251 case 2: /* medium */ 1252 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; 1253 break; 1254 case 3: /* high */ 1255 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_HIGH; 1256 break; 1257 case 4: /* full */ 1258 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_FULL; 1259 break; 1260 default: 1261 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 1262 hid_warn(ctlr->hdev, "Invalid battery status\n"); 1263 break; 1264 } 1265 spin_unlock_irqrestore(&ctlr->lock, flags); 1266 1267 /* Parse the buttons and sticks */ 1268 btns = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1269 1270 if (jc_type_has_left(ctlr)) { 1271 u16 raw_x; 1272 u16 raw_y; 1273 s32 x; 1274 s32 y; 1275 1276 /* get raw stick values */ 1277 raw_x = hid_field_extract(ctlr->hdev, rep->left_stick, 0, 12); 1278 raw_y = hid_field_extract(ctlr->hdev, 1279 rep->left_stick + 1, 4, 12); 1280 /* map the stick values */ 1281 x = joycon_map_stick_val(&ctlr->left_stick_cal_x, raw_x); 1282 y = -joycon_map_stick_val(&ctlr->left_stick_cal_y, raw_y); 1283 /* report sticks */ 1284 input_report_abs(dev, ABS_X, x); 1285 input_report_abs(dev, ABS_Y, y); 1286 1287 /* report buttons */ 1288 input_report_key(dev, BTN_TL, btns & JC_BTN_L); 1289 input_report_key(dev, BTN_TL2, btns & JC_BTN_ZL); 1290 input_report_key(dev, BTN_SELECT, btns & JC_BTN_MINUS); 1291 input_report_key(dev, BTN_THUMBL, btns & JC_BTN_LSTICK); 1292 input_report_key(dev, BTN_Z, btns & JC_BTN_CAP); 1293 1294 if (jc_type_is_joycon(ctlr)) { 1295 /* Report the S buttons as the non-existent triggers */ 1296 input_report_key(dev, BTN_TR, btns & JC_BTN_SL_L); 1297 input_report_key(dev, BTN_TR2, btns & JC_BTN_SR_L); 1298 1299 /* Report d-pad as digital buttons for the joy-cons */ 1300 input_report_key(dev, BTN_DPAD_DOWN, 1301 btns & JC_BTN_DOWN); 1302 input_report_key(dev, BTN_DPAD_UP, btns & JC_BTN_UP); 1303 input_report_key(dev, BTN_DPAD_RIGHT, 1304 btns & JC_BTN_RIGHT); 1305 input_report_key(dev, BTN_DPAD_LEFT, 1306 btns & JC_BTN_LEFT); 1307 } else { 1308 int hatx = 0; 1309 int haty = 0; 1310 1311 /* d-pad x */ 1312 if (btns & JC_BTN_LEFT) 1313 hatx = -1; 1314 else if (btns & JC_BTN_RIGHT) 1315 hatx = 1; 1316 input_report_abs(dev, ABS_HAT0X, hatx); 1317 1318 /* d-pad y */ 1319 if (btns & JC_BTN_UP) 1320 haty = -1; 1321 else if (btns & JC_BTN_DOWN) 1322 haty = 1; 1323 input_report_abs(dev, ABS_HAT0Y, haty); 1324 } 1325 } 1326 if (jc_type_has_right(ctlr)) { 1327 u16 raw_x; 1328 u16 raw_y; 1329 s32 x; 1330 s32 y; 1331 1332 /* get raw stick values */ 1333 raw_x = hid_field_extract(ctlr->hdev, rep->right_stick, 0, 12); 1334 raw_y = hid_field_extract(ctlr->hdev, 1335 rep->right_stick + 1, 4, 12); 1336 /* map stick values */ 1337 x = joycon_map_stick_val(&ctlr->right_stick_cal_x, raw_x); 1338 y = -joycon_map_stick_val(&ctlr->right_stick_cal_y, raw_y); 1339 /* report sticks */ 1340 input_report_abs(dev, ABS_RX, x); 1341 input_report_abs(dev, ABS_RY, y); 1342 1343 /* report buttons */ 1344 input_report_key(dev, BTN_TR, btns & JC_BTN_R); 1345 input_report_key(dev, BTN_TR2, btns & JC_BTN_ZR); 1346 if (jc_type_is_joycon(ctlr)) { 1347 /* Report the S buttons as the non-existent triggers */ 1348 input_report_key(dev, BTN_TL, btns & JC_BTN_SL_R); 1349 input_report_key(dev, BTN_TL2, btns & JC_BTN_SR_R); 1350 } 1351 input_report_key(dev, BTN_START, btns & JC_BTN_PLUS); 1352 input_report_key(dev, BTN_THUMBR, btns & JC_BTN_RSTICK); 1353 input_report_key(dev, BTN_MODE, btns & JC_BTN_HOME); 1354 input_report_key(dev, BTN_WEST, btns & JC_BTN_Y); 1355 input_report_key(dev, BTN_NORTH, btns & JC_BTN_X); 1356 input_report_key(dev, BTN_EAST, btns & JC_BTN_A); 1357 input_report_key(dev, BTN_SOUTH, btns & JC_BTN_B); 1358 } 1359 1360 input_sync(dev); 1361 1362 /* 1363 * Immediately after receiving a report is the most reliable time to 1364 * send a subcommand to the controller. Wake any subcommand senders 1365 * waiting for a report. 1366 */ 1367 if (unlikely(mutex_is_locked(&ctlr->output_mutex))) { 1368 spin_lock_irqsave(&ctlr->lock, flags); 1369 ctlr->received_input_report = true; 1370 spin_unlock_irqrestore(&ctlr->lock, flags); 1371 wake_up(&ctlr->wait); 1372 } 1373 1374 /* parse IMU data if present */ 1375 if (rep->id == JC_INPUT_IMU_DATA) 1376 joycon_parse_imu_report(ctlr, rep); 1377 } 1378 1379 static int joycon_send_rumble_data(struct joycon_ctlr *ctlr) 1380 { 1381 int ret; 1382 unsigned long flags; 1383 struct joycon_rumble_output rumble_output = { 0 }; 1384 1385 spin_lock_irqsave(&ctlr->lock, flags); 1386 /* 1387 * If the controller has been removed, just return ENODEV so the LED 1388 * subsystem doesn't print invalid errors on removal. 1389 */ 1390 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 1391 spin_unlock_irqrestore(&ctlr->lock, flags); 1392 return -ENODEV; 1393 } 1394 memcpy(rumble_output.rumble_data, 1395 ctlr->rumble_data[ctlr->rumble_queue_tail], 1396 JC_RUMBLE_DATA_SIZE); 1397 spin_unlock_irqrestore(&ctlr->lock, flags); 1398 1399 rumble_output.output_id = JC_OUTPUT_RUMBLE_ONLY; 1400 rumble_output.packet_num = ctlr->subcmd_num; 1401 if (++ctlr->subcmd_num > 0xF) 1402 ctlr->subcmd_num = 0; 1403 1404 joycon_enforce_subcmd_rate(ctlr); 1405 1406 ret = __joycon_hid_send(ctlr->hdev, (u8 *)&rumble_output, 1407 sizeof(rumble_output)); 1408 return ret; 1409 } 1410 1411 static void joycon_rumble_worker(struct work_struct *work) 1412 { 1413 struct joycon_ctlr *ctlr = container_of(work, struct joycon_ctlr, 1414 rumble_worker); 1415 unsigned long flags; 1416 bool again = true; 1417 int ret; 1418 1419 while (again) { 1420 mutex_lock(&ctlr->output_mutex); 1421 ret = joycon_send_rumble_data(ctlr); 1422 mutex_unlock(&ctlr->output_mutex); 1423 1424 /* -ENODEV means the controller was just unplugged */ 1425 spin_lock_irqsave(&ctlr->lock, flags); 1426 if (ret < 0 && ret != -ENODEV && 1427 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1428 hid_warn(ctlr->hdev, "Failed to set rumble; e=%d", ret); 1429 1430 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1431 if (ctlr->rumble_queue_tail != ctlr->rumble_queue_head) { 1432 if (++ctlr->rumble_queue_tail >= JC_RUMBLE_QUEUE_SIZE) 1433 ctlr->rumble_queue_tail = 0; 1434 } else { 1435 again = false; 1436 } 1437 spin_unlock_irqrestore(&ctlr->lock, flags); 1438 } 1439 } 1440 1441 #if IS_ENABLED(CONFIG_NINTENDO_FF) 1442 static struct joycon_rumble_freq_data joycon_find_rumble_freq(u16 freq) 1443 { 1444 const size_t length = ARRAY_SIZE(joycon_rumble_frequencies); 1445 const struct joycon_rumble_freq_data *data = joycon_rumble_frequencies; 1446 int i = 0; 1447 1448 if (freq > data[0].freq) { 1449 for (i = 1; i < length - 1; i++) { 1450 if (freq > data[i - 1].freq && freq <= data[i].freq) 1451 break; 1452 } 1453 } 1454 1455 return data[i]; 1456 } 1457 1458 static struct joycon_rumble_amp_data joycon_find_rumble_amp(u16 amp) 1459 { 1460 const size_t length = ARRAY_SIZE(joycon_rumble_amplitudes); 1461 const struct joycon_rumble_amp_data *data = joycon_rumble_amplitudes; 1462 int i = 0; 1463 1464 if (amp > data[0].amp) { 1465 for (i = 1; i < length - 1; i++) { 1466 if (amp > data[i - 1].amp && amp <= data[i].amp) 1467 break; 1468 } 1469 } 1470 1471 return data[i]; 1472 } 1473 1474 static void joycon_encode_rumble(u8 *data, u16 freq_low, u16 freq_high, u16 amp) 1475 { 1476 struct joycon_rumble_freq_data freq_data_low; 1477 struct joycon_rumble_freq_data freq_data_high; 1478 struct joycon_rumble_amp_data amp_data; 1479 1480 freq_data_low = joycon_find_rumble_freq(freq_low); 1481 freq_data_high = joycon_find_rumble_freq(freq_high); 1482 amp_data = joycon_find_rumble_amp(amp); 1483 1484 data[0] = (freq_data_high.high >> 8) & 0xFF; 1485 data[1] = (freq_data_high.high & 0xFF) + amp_data.high; 1486 data[2] = freq_data_low.low + ((amp_data.low >> 8) & 0xFF); 1487 data[3] = amp_data.low & 0xFF; 1488 } 1489 1490 static const u16 JOYCON_MAX_RUMBLE_HIGH_FREQ = 1253; 1491 static const u16 JOYCON_MIN_RUMBLE_HIGH_FREQ = 82; 1492 static const u16 JOYCON_MAX_RUMBLE_LOW_FREQ = 626; 1493 static const u16 JOYCON_MIN_RUMBLE_LOW_FREQ = 41; 1494 1495 static void joycon_clamp_rumble_freqs(struct joycon_ctlr *ctlr) 1496 { 1497 unsigned long flags; 1498 1499 spin_lock_irqsave(&ctlr->lock, flags); 1500 ctlr->rumble_ll_freq = clamp(ctlr->rumble_ll_freq, 1501 JOYCON_MIN_RUMBLE_LOW_FREQ, 1502 JOYCON_MAX_RUMBLE_LOW_FREQ); 1503 ctlr->rumble_lh_freq = clamp(ctlr->rumble_lh_freq, 1504 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1505 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1506 ctlr->rumble_rl_freq = clamp(ctlr->rumble_rl_freq, 1507 JOYCON_MIN_RUMBLE_LOW_FREQ, 1508 JOYCON_MAX_RUMBLE_LOW_FREQ); 1509 ctlr->rumble_rh_freq = clamp(ctlr->rumble_rh_freq, 1510 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1511 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1512 spin_unlock_irqrestore(&ctlr->lock, flags); 1513 } 1514 1515 static int joycon_set_rumble(struct joycon_ctlr *ctlr, u16 amp_r, u16 amp_l, 1516 bool schedule_now) 1517 { 1518 u8 data[JC_RUMBLE_DATA_SIZE]; 1519 u16 amp; 1520 u16 freq_r_low; 1521 u16 freq_r_high; 1522 u16 freq_l_low; 1523 u16 freq_l_high; 1524 unsigned long flags; 1525 1526 spin_lock_irqsave(&ctlr->lock, flags); 1527 freq_r_low = ctlr->rumble_rl_freq; 1528 freq_r_high = ctlr->rumble_rh_freq; 1529 freq_l_low = ctlr->rumble_ll_freq; 1530 freq_l_high = ctlr->rumble_lh_freq; 1531 /* limit number of silent rumble packets to reduce traffic */ 1532 if (amp_l != 0 || amp_r != 0) 1533 ctlr->rumble_zero_countdown = JC_RUMBLE_ZERO_AMP_PKT_CNT; 1534 spin_unlock_irqrestore(&ctlr->lock, flags); 1535 1536 /* right joy-con */ 1537 amp = amp_r * (u32)joycon_max_rumble_amp / 65535; 1538 joycon_encode_rumble(data + 4, freq_r_low, freq_r_high, amp); 1539 1540 /* left joy-con */ 1541 amp = amp_l * (u32)joycon_max_rumble_amp / 65535; 1542 joycon_encode_rumble(data, freq_l_low, freq_l_high, amp); 1543 1544 spin_lock_irqsave(&ctlr->lock, flags); 1545 if (++ctlr->rumble_queue_head >= JC_RUMBLE_QUEUE_SIZE) 1546 ctlr->rumble_queue_head = 0; 1547 memcpy(ctlr->rumble_data[ctlr->rumble_queue_head], data, 1548 JC_RUMBLE_DATA_SIZE); 1549 1550 /* don't wait for the periodic send (reduces latency) */ 1551 if (schedule_now && ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1552 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1553 1554 spin_unlock_irqrestore(&ctlr->lock, flags); 1555 1556 return 0; 1557 } 1558 1559 static int joycon_play_effect(struct input_dev *dev, void *data, 1560 struct ff_effect *effect) 1561 { 1562 struct joycon_ctlr *ctlr = input_get_drvdata(dev); 1563 1564 if (effect->type != FF_RUMBLE) 1565 return 0; 1566 1567 return joycon_set_rumble(ctlr, 1568 effect->u.rumble.weak_magnitude, 1569 effect->u.rumble.strong_magnitude, 1570 true); 1571 } 1572 #endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 1573 1574 static const unsigned int joycon_button_inputs_l[] = { 1575 BTN_SELECT, BTN_Z, BTN_THUMBL, 1576 BTN_TL, BTN_TL2, 1577 0 /* 0 signals end of array */ 1578 }; 1579 1580 static const unsigned int joycon_button_inputs_r[] = { 1581 BTN_START, BTN_MODE, BTN_THUMBR, 1582 BTN_SOUTH, BTN_EAST, BTN_NORTH, BTN_WEST, 1583 BTN_TR, BTN_TR2, 1584 0 /* 0 signals end of array */ 1585 }; 1586 1587 /* We report joy-con d-pad inputs as buttons and pro controller as a hat. */ 1588 static const unsigned int joycon_dpad_inputs_jc[] = { 1589 BTN_DPAD_UP, BTN_DPAD_DOWN, BTN_DPAD_LEFT, BTN_DPAD_RIGHT, 1590 0 /* 0 signals end of array */ 1591 }; 1592 1593 static int joycon_input_create(struct joycon_ctlr *ctlr) 1594 { 1595 struct hid_device *hdev; 1596 const char *name; 1597 const char *imu_name; 1598 int ret; 1599 int i; 1600 1601 hdev = ctlr->hdev; 1602 1603 switch (hdev->product) { 1604 case USB_DEVICE_ID_NINTENDO_PROCON: 1605 name = "Nintendo Switch Pro Controller"; 1606 imu_name = "Nintendo Switch Pro Controller IMU"; 1607 break; 1608 case USB_DEVICE_ID_NINTENDO_CHRGGRIP: 1609 if (jc_type_has_left(ctlr)) { 1610 name = "Nintendo Switch Left Joy-Con (Grip)"; 1611 imu_name = "Nintendo Switch Left Joy-Con IMU (Grip)"; 1612 } else { 1613 name = "Nintendo Switch Right Joy-Con (Grip)"; 1614 imu_name = "Nintendo Switch Right Joy-Con IMU (Grip)"; 1615 } 1616 break; 1617 case USB_DEVICE_ID_NINTENDO_JOYCONL: 1618 name = "Nintendo Switch Left Joy-Con"; 1619 imu_name = "Nintendo Switch Left Joy-Con IMU"; 1620 break; 1621 case USB_DEVICE_ID_NINTENDO_JOYCONR: 1622 name = "Nintendo Switch Right Joy-Con"; 1623 imu_name = "Nintendo Switch Right Joy-Con IMU"; 1624 break; 1625 default: /* Should be impossible */ 1626 hid_err(hdev, "Invalid hid product\n"); 1627 return -EINVAL; 1628 } 1629 1630 ctlr->input = devm_input_allocate_device(&hdev->dev); 1631 if (!ctlr->input) 1632 return -ENOMEM; 1633 ctlr->input->id.bustype = hdev->bus; 1634 ctlr->input->id.vendor = hdev->vendor; 1635 ctlr->input->id.product = hdev->product; 1636 ctlr->input->id.version = hdev->version; 1637 ctlr->input->uniq = ctlr->mac_addr_str; 1638 ctlr->input->name = name; 1639 ctlr->input->phys = hdev->phys; 1640 input_set_drvdata(ctlr->input, ctlr); 1641 1642 /* set up sticks and buttons */ 1643 if (jc_type_has_left(ctlr)) { 1644 input_set_abs_params(ctlr->input, ABS_X, 1645 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1646 JC_STICK_FUZZ, JC_STICK_FLAT); 1647 input_set_abs_params(ctlr->input, ABS_Y, 1648 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1649 JC_STICK_FUZZ, JC_STICK_FLAT); 1650 1651 for (i = 0; joycon_button_inputs_l[i] > 0; i++) 1652 input_set_capability(ctlr->input, EV_KEY, 1653 joycon_button_inputs_l[i]); 1654 1655 /* configure d-pad differently for joy-con vs pro controller */ 1656 if (hdev->product != USB_DEVICE_ID_NINTENDO_PROCON) { 1657 for (i = 0; joycon_dpad_inputs_jc[i] > 0; i++) 1658 input_set_capability(ctlr->input, EV_KEY, 1659 joycon_dpad_inputs_jc[i]); 1660 } else { 1661 input_set_abs_params(ctlr->input, ABS_HAT0X, 1662 -JC_MAX_DPAD_MAG, JC_MAX_DPAD_MAG, 1663 JC_DPAD_FUZZ, JC_DPAD_FLAT); 1664 input_set_abs_params(ctlr->input, ABS_HAT0Y, 1665 -JC_MAX_DPAD_MAG, JC_MAX_DPAD_MAG, 1666 JC_DPAD_FUZZ, JC_DPAD_FLAT); 1667 } 1668 } 1669 if (jc_type_has_right(ctlr)) { 1670 input_set_abs_params(ctlr->input, ABS_RX, 1671 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1672 JC_STICK_FUZZ, JC_STICK_FLAT); 1673 input_set_abs_params(ctlr->input, ABS_RY, 1674 -JC_MAX_STICK_MAG, JC_MAX_STICK_MAG, 1675 JC_STICK_FUZZ, JC_STICK_FLAT); 1676 1677 for (i = 0; joycon_button_inputs_r[i] > 0; i++) 1678 input_set_capability(ctlr->input, EV_KEY, 1679 joycon_button_inputs_r[i]); 1680 } 1681 1682 /* Let's report joy-con S triggers separately */ 1683 if (hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL) { 1684 input_set_capability(ctlr->input, EV_KEY, BTN_TR); 1685 input_set_capability(ctlr->input, EV_KEY, BTN_TR2); 1686 } else if (hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR) { 1687 input_set_capability(ctlr->input, EV_KEY, BTN_TL); 1688 input_set_capability(ctlr->input, EV_KEY, BTN_TL2); 1689 } 1690 1691 #if IS_ENABLED(CONFIG_NINTENDO_FF) 1692 /* set up rumble */ 1693 input_set_capability(ctlr->input, EV_FF, FF_RUMBLE); 1694 input_ff_create_memless(ctlr->input, NULL, joycon_play_effect); 1695 ctlr->rumble_ll_freq = JC_RUMBLE_DFLT_LOW_FREQ; 1696 ctlr->rumble_lh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 1697 ctlr->rumble_rl_freq = JC_RUMBLE_DFLT_LOW_FREQ; 1698 ctlr->rumble_rh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 1699 joycon_clamp_rumble_freqs(ctlr); 1700 joycon_set_rumble(ctlr, 0, 0, false); 1701 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1702 #endif 1703 1704 ret = input_register_device(ctlr->input); 1705 if (ret) 1706 return ret; 1707 1708 /* configure the imu input device */ 1709 ctlr->imu_input = devm_input_allocate_device(&hdev->dev); 1710 if (!ctlr->imu_input) 1711 return -ENOMEM; 1712 1713 ctlr->imu_input->id.bustype = hdev->bus; 1714 ctlr->imu_input->id.vendor = hdev->vendor; 1715 ctlr->imu_input->id.product = hdev->product; 1716 ctlr->imu_input->id.version = hdev->version; 1717 ctlr->imu_input->uniq = ctlr->mac_addr_str; 1718 ctlr->imu_input->name = imu_name; 1719 ctlr->imu_input->phys = hdev->phys; 1720 input_set_drvdata(ctlr->imu_input, ctlr); 1721 1722 /* configure imu axes */ 1723 input_set_abs_params(ctlr->imu_input, ABS_X, 1724 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1725 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1726 input_set_abs_params(ctlr->imu_input, ABS_Y, 1727 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1728 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1729 input_set_abs_params(ctlr->imu_input, ABS_Z, 1730 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 1731 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 1732 input_abs_set_res(ctlr->imu_input, ABS_X, JC_IMU_ACCEL_RES_PER_G); 1733 input_abs_set_res(ctlr->imu_input, ABS_Y, JC_IMU_ACCEL_RES_PER_G); 1734 input_abs_set_res(ctlr->imu_input, ABS_Z, JC_IMU_ACCEL_RES_PER_G); 1735 1736 input_set_abs_params(ctlr->imu_input, ABS_RX, 1737 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1738 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1739 input_set_abs_params(ctlr->imu_input, ABS_RY, 1740 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1741 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1742 input_set_abs_params(ctlr->imu_input, ABS_RZ, 1743 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 1744 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 1745 1746 input_abs_set_res(ctlr->imu_input, ABS_RX, JC_IMU_GYRO_RES_PER_DPS); 1747 input_abs_set_res(ctlr->imu_input, ABS_RY, JC_IMU_GYRO_RES_PER_DPS); 1748 input_abs_set_res(ctlr->imu_input, ABS_RZ, JC_IMU_GYRO_RES_PER_DPS); 1749 1750 __set_bit(EV_MSC, ctlr->imu_input->evbit); 1751 __set_bit(MSC_TIMESTAMP, ctlr->imu_input->mscbit); 1752 __set_bit(INPUT_PROP_ACCELEROMETER, ctlr->imu_input->propbit); 1753 1754 ret = input_register_device(ctlr->imu_input); 1755 if (ret) 1756 return ret; 1757 1758 return 0; 1759 } 1760 1761 static int joycon_player_led_brightness_set(struct led_classdev *led, 1762 enum led_brightness brightness) 1763 { 1764 struct device *dev = led->dev->parent; 1765 struct hid_device *hdev = to_hid_device(dev); 1766 struct joycon_ctlr *ctlr; 1767 int val = 0; 1768 int i; 1769 int ret; 1770 int num; 1771 1772 ctlr = hid_get_drvdata(hdev); 1773 if (!ctlr) { 1774 hid_err(hdev, "No controller data\n"); 1775 return -ENODEV; 1776 } 1777 1778 /* determine which player led this is */ 1779 for (num = 0; num < JC_NUM_LEDS; num++) { 1780 if (&ctlr->leds[num] == led) 1781 break; 1782 } 1783 if (num >= JC_NUM_LEDS) 1784 return -EINVAL; 1785 1786 mutex_lock(&ctlr->output_mutex); 1787 for (i = 0; i < JC_NUM_LEDS; i++) { 1788 if (i == num) 1789 val |= brightness << i; 1790 else 1791 val |= ctlr->leds[i].brightness << i; 1792 } 1793 ret = joycon_set_player_leds(ctlr, 0, val); 1794 mutex_unlock(&ctlr->output_mutex); 1795 1796 return ret; 1797 } 1798 1799 static int joycon_home_led_brightness_set(struct led_classdev *led, 1800 enum led_brightness brightness) 1801 { 1802 struct device *dev = led->dev->parent; 1803 struct hid_device *hdev = to_hid_device(dev); 1804 struct joycon_ctlr *ctlr; 1805 struct joycon_subcmd_request *req; 1806 u8 buffer[sizeof(*req) + 5] = { 0 }; 1807 u8 *data; 1808 int ret; 1809 1810 ctlr = hid_get_drvdata(hdev); 1811 if (!ctlr) { 1812 hid_err(hdev, "No controller data\n"); 1813 return -ENODEV; 1814 } 1815 1816 req = (struct joycon_subcmd_request *)buffer; 1817 req->subcmd_id = JC_SUBCMD_SET_HOME_LIGHT; 1818 data = req->data; 1819 data[0] = 0x01; 1820 data[1] = brightness << 4; 1821 data[2] = brightness | (brightness << 4); 1822 data[3] = 0x11; 1823 data[4] = 0x11; 1824 1825 hid_dbg(hdev, "setting home led brightness\n"); 1826 mutex_lock(&ctlr->output_mutex); 1827 ret = joycon_send_subcmd(ctlr, req, 5, HZ/4); 1828 mutex_unlock(&ctlr->output_mutex); 1829 1830 return ret; 1831 } 1832 1833 static DEFINE_MUTEX(joycon_input_num_mutex); 1834 static int joycon_leds_create(struct joycon_ctlr *ctlr) 1835 { 1836 struct hid_device *hdev = ctlr->hdev; 1837 struct device *dev = &hdev->dev; 1838 const char *d_name = dev_name(dev); 1839 struct led_classdev *led; 1840 char *name; 1841 int ret = 0; 1842 int i; 1843 static int input_num = 1; 1844 1845 /* Set the default controller player leds based on controller number */ 1846 mutex_lock(&joycon_input_num_mutex); 1847 mutex_lock(&ctlr->output_mutex); 1848 ret = joycon_set_player_leds(ctlr, 0, 0xF >> (4 - input_num)); 1849 if (ret) 1850 hid_warn(ctlr->hdev, "Failed to set leds; ret=%d\n", ret); 1851 mutex_unlock(&ctlr->output_mutex); 1852 1853 /* configure the player LEDs */ 1854 for (i = 0; i < JC_NUM_LEDS; i++) { 1855 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 1856 d_name, 1857 "green", 1858 joycon_player_led_names[i]); 1859 if (!name) { 1860 mutex_unlock(&joycon_input_num_mutex); 1861 return -ENOMEM; 1862 } 1863 1864 led = &ctlr->leds[i]; 1865 led->name = name; 1866 led->brightness = ((i + 1) <= input_num) ? 1 : 0; 1867 led->max_brightness = 1; 1868 led->brightness_set_blocking = 1869 joycon_player_led_brightness_set; 1870 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 1871 1872 ret = devm_led_classdev_register(&hdev->dev, led); 1873 if (ret) { 1874 hid_err(hdev, "Failed registering %s LED\n", led->name); 1875 mutex_unlock(&joycon_input_num_mutex); 1876 return ret; 1877 } 1878 } 1879 1880 if (++input_num > 4) 1881 input_num = 1; 1882 mutex_unlock(&joycon_input_num_mutex); 1883 1884 /* configure the home LED */ 1885 if (jc_type_has_right(ctlr)) { 1886 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 1887 d_name, 1888 "blue", 1889 LED_FUNCTION_PLAYER5); 1890 if (!name) 1891 return -ENOMEM; 1892 1893 led = &ctlr->home_led; 1894 led->name = name; 1895 led->brightness = 0; 1896 led->max_brightness = 0xF; 1897 led->brightness_set_blocking = joycon_home_led_brightness_set; 1898 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 1899 ret = devm_led_classdev_register(&hdev->dev, led); 1900 if (ret) { 1901 hid_err(hdev, "Failed registering home led\n"); 1902 return ret; 1903 } 1904 /* Set the home LED to 0 as default state */ 1905 ret = joycon_home_led_brightness_set(led, 0); 1906 if (ret) { 1907 hid_err(hdev, "Failed to set home LED dflt; ret=%d\n", 1908 ret); 1909 return ret; 1910 } 1911 } 1912 1913 return 0; 1914 } 1915 1916 static int joycon_battery_get_property(struct power_supply *supply, 1917 enum power_supply_property prop, 1918 union power_supply_propval *val) 1919 { 1920 struct joycon_ctlr *ctlr = power_supply_get_drvdata(supply); 1921 unsigned long flags; 1922 int ret = 0; 1923 u8 capacity; 1924 bool charging; 1925 bool powered; 1926 1927 spin_lock_irqsave(&ctlr->lock, flags); 1928 capacity = ctlr->battery_capacity; 1929 charging = ctlr->battery_charging; 1930 powered = ctlr->host_powered; 1931 spin_unlock_irqrestore(&ctlr->lock, flags); 1932 1933 switch (prop) { 1934 case POWER_SUPPLY_PROP_PRESENT: 1935 val->intval = 1; 1936 break; 1937 case POWER_SUPPLY_PROP_SCOPE: 1938 val->intval = POWER_SUPPLY_SCOPE_DEVICE; 1939 break; 1940 case POWER_SUPPLY_PROP_CAPACITY_LEVEL: 1941 val->intval = capacity; 1942 break; 1943 case POWER_SUPPLY_PROP_STATUS: 1944 if (charging) 1945 val->intval = POWER_SUPPLY_STATUS_CHARGING; 1946 else if (capacity == POWER_SUPPLY_CAPACITY_LEVEL_FULL && 1947 powered) 1948 val->intval = POWER_SUPPLY_STATUS_FULL; 1949 else 1950 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 1951 break; 1952 default: 1953 ret = -EINVAL; 1954 break; 1955 } 1956 return ret; 1957 } 1958 1959 static enum power_supply_property joycon_battery_props[] = { 1960 POWER_SUPPLY_PROP_PRESENT, 1961 POWER_SUPPLY_PROP_CAPACITY_LEVEL, 1962 POWER_SUPPLY_PROP_SCOPE, 1963 POWER_SUPPLY_PROP_STATUS, 1964 }; 1965 1966 static int joycon_power_supply_create(struct joycon_ctlr *ctlr) 1967 { 1968 struct hid_device *hdev = ctlr->hdev; 1969 struct power_supply_config supply_config = { .drv_data = ctlr, }; 1970 const char * const name_fmt = "nintendo_switch_controller_battery_%s"; 1971 int ret = 0; 1972 1973 /* Set initially to unknown before receiving first input report */ 1974 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 1975 1976 /* Configure the battery's description */ 1977 ctlr->battery_desc.properties = joycon_battery_props; 1978 ctlr->battery_desc.num_properties = 1979 ARRAY_SIZE(joycon_battery_props); 1980 ctlr->battery_desc.get_property = joycon_battery_get_property; 1981 ctlr->battery_desc.type = POWER_SUPPLY_TYPE_BATTERY; 1982 ctlr->battery_desc.use_for_apm = 0; 1983 ctlr->battery_desc.name = devm_kasprintf(&hdev->dev, GFP_KERNEL, 1984 name_fmt, 1985 dev_name(&hdev->dev)); 1986 if (!ctlr->battery_desc.name) 1987 return -ENOMEM; 1988 1989 ctlr->battery = devm_power_supply_register(&hdev->dev, 1990 &ctlr->battery_desc, 1991 &supply_config); 1992 if (IS_ERR(ctlr->battery)) { 1993 ret = PTR_ERR(ctlr->battery); 1994 hid_err(hdev, "Failed to register battery; ret=%d\n", ret); 1995 return ret; 1996 } 1997 1998 return power_supply_powers(ctlr->battery, &hdev->dev); 1999 } 2000 2001 static int joycon_read_info(struct joycon_ctlr *ctlr) 2002 { 2003 int ret; 2004 int i; 2005 int j; 2006 struct joycon_subcmd_request req = { 0 }; 2007 struct joycon_input_report *report; 2008 2009 req.subcmd_id = JC_SUBCMD_REQ_DEV_INFO; 2010 ret = joycon_send_subcmd(ctlr, &req, 0, HZ); 2011 if (ret) { 2012 hid_err(ctlr->hdev, "Failed to get joycon info; ret=%d\n", ret); 2013 return ret; 2014 } 2015 2016 report = (struct joycon_input_report *)ctlr->input_buf; 2017 2018 for (i = 4, j = 0; j < 6; i++, j++) 2019 ctlr->mac_addr[j] = report->subcmd_reply.data[i]; 2020 2021 ctlr->mac_addr_str = devm_kasprintf(&ctlr->hdev->dev, GFP_KERNEL, 2022 "%02X:%02X:%02X:%02X:%02X:%02X", 2023 ctlr->mac_addr[0], 2024 ctlr->mac_addr[1], 2025 ctlr->mac_addr[2], 2026 ctlr->mac_addr[3], 2027 ctlr->mac_addr[4], 2028 ctlr->mac_addr[5]); 2029 if (!ctlr->mac_addr_str) 2030 return -ENOMEM; 2031 hid_info(ctlr->hdev, "controller MAC = %s\n", ctlr->mac_addr_str); 2032 2033 /* Retrieve the type so we can distinguish for charging grip */ 2034 ctlr->ctlr_type = report->subcmd_reply.data[2]; 2035 2036 return 0; 2037 } 2038 2039 /* Common handler for parsing inputs */ 2040 static int joycon_ctlr_read_handler(struct joycon_ctlr *ctlr, u8 *data, 2041 int size) 2042 { 2043 if (data[0] == JC_INPUT_SUBCMD_REPLY || data[0] == JC_INPUT_IMU_DATA || 2044 data[0] == JC_INPUT_MCU_DATA) { 2045 if (size >= 12) /* make sure it contains the input report */ 2046 joycon_parse_report(ctlr, 2047 (struct joycon_input_report *)data); 2048 } 2049 2050 return 0; 2051 } 2052 2053 static int joycon_ctlr_handle_event(struct joycon_ctlr *ctlr, u8 *data, 2054 int size) 2055 { 2056 int ret = 0; 2057 bool match = false; 2058 struct joycon_input_report *report; 2059 2060 if (unlikely(mutex_is_locked(&ctlr->output_mutex)) && 2061 ctlr->msg_type != JOYCON_MSG_TYPE_NONE) { 2062 switch (ctlr->msg_type) { 2063 case JOYCON_MSG_TYPE_USB: 2064 if (size < 2) 2065 break; 2066 if (data[0] == JC_INPUT_USB_RESPONSE && 2067 data[1] == ctlr->usb_ack_match) 2068 match = true; 2069 break; 2070 case JOYCON_MSG_TYPE_SUBCMD: 2071 if (size < sizeof(struct joycon_input_report) || 2072 data[0] != JC_INPUT_SUBCMD_REPLY) 2073 break; 2074 report = (struct joycon_input_report *)data; 2075 if (report->subcmd_reply.id == ctlr->subcmd_ack_match) 2076 match = true; 2077 break; 2078 default: 2079 break; 2080 } 2081 2082 if (match) { 2083 memcpy(ctlr->input_buf, data, 2084 min(size, (int)JC_MAX_RESP_SIZE)); 2085 ctlr->msg_type = JOYCON_MSG_TYPE_NONE; 2086 ctlr->received_resp = true; 2087 wake_up(&ctlr->wait); 2088 2089 /* This message has been handled */ 2090 return 1; 2091 } 2092 } 2093 2094 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) 2095 ret = joycon_ctlr_read_handler(ctlr, data, size); 2096 2097 return ret; 2098 } 2099 2100 static int nintendo_hid_event(struct hid_device *hdev, 2101 struct hid_report *report, u8 *raw_data, int size) 2102 { 2103 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2104 2105 if (size < 1) 2106 return -EINVAL; 2107 2108 return joycon_ctlr_handle_event(ctlr, raw_data, size); 2109 } 2110 2111 static int nintendo_hid_probe(struct hid_device *hdev, 2112 const struct hid_device_id *id) 2113 { 2114 int ret; 2115 struct joycon_ctlr *ctlr; 2116 2117 hid_dbg(hdev, "probe - start\n"); 2118 2119 ctlr = devm_kzalloc(&hdev->dev, sizeof(*ctlr), GFP_KERNEL); 2120 if (!ctlr) { 2121 ret = -ENOMEM; 2122 goto err; 2123 } 2124 2125 ctlr->hdev = hdev; 2126 ctlr->ctlr_state = JOYCON_CTLR_STATE_INIT; 2127 ctlr->rumble_queue_head = JC_RUMBLE_QUEUE_SIZE - 1; 2128 ctlr->rumble_queue_tail = 0; 2129 hid_set_drvdata(hdev, ctlr); 2130 mutex_init(&ctlr->output_mutex); 2131 init_waitqueue_head(&ctlr->wait); 2132 spin_lock_init(&ctlr->lock); 2133 ctlr->rumble_queue = alloc_workqueue("hid-nintendo-rumble_wq", 2134 WQ_FREEZABLE | WQ_MEM_RECLAIM, 0); 2135 if (!ctlr->rumble_queue) { 2136 ret = -ENOMEM; 2137 goto err; 2138 } 2139 INIT_WORK(&ctlr->rumble_worker, joycon_rumble_worker); 2140 2141 ret = hid_parse(hdev); 2142 if (ret) { 2143 hid_err(hdev, "HID parse failed\n"); 2144 goto err_wq; 2145 } 2146 2147 /* 2148 * Patch the hw version of pro controller/joycons, so applications can 2149 * distinguish between the default HID mappings and the mappings defined 2150 * by the Linux game controller spec. This is important for the SDL2 2151 * library, which has a game controller database, which uses device ids 2152 * in combination with version as a key. 2153 */ 2154 hdev->version |= 0x8000; 2155 2156 ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW); 2157 if (ret) { 2158 hid_err(hdev, "HW start failed\n"); 2159 goto err_wq; 2160 } 2161 2162 ret = hid_hw_open(hdev); 2163 if (ret) { 2164 hid_err(hdev, "cannot start hardware I/O\n"); 2165 goto err_stop; 2166 } 2167 2168 hid_device_io_start(hdev); 2169 2170 /* Initialize the controller */ 2171 mutex_lock(&ctlr->output_mutex); 2172 /* if handshake command fails, assume ble pro controller */ 2173 if ((jc_type_is_procon(ctlr) || jc_type_is_chrggrip(ctlr)) && 2174 !joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ)) { 2175 hid_dbg(hdev, "detected USB controller\n"); 2176 /* set baudrate for improved latency */ 2177 ret = joycon_send_usb(ctlr, JC_USB_CMD_BAUDRATE_3M, HZ); 2178 if (ret) { 2179 hid_err(hdev, "Failed to set baudrate; ret=%d\n", ret); 2180 goto err_mutex; 2181 } 2182 /* handshake */ 2183 ret = joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ); 2184 if (ret) { 2185 hid_err(hdev, "Failed handshake; ret=%d\n", ret); 2186 goto err_mutex; 2187 } 2188 /* 2189 * Set no timeout (to keep controller in USB mode). 2190 * This doesn't send a response, so ignore the timeout. 2191 */ 2192 joycon_send_usb(ctlr, JC_USB_CMD_NO_TIMEOUT, HZ/10); 2193 } else if (jc_type_is_chrggrip(ctlr)) { 2194 hid_err(hdev, "Failed charging grip handshake\n"); 2195 ret = -ETIMEDOUT; 2196 goto err_mutex; 2197 } 2198 2199 /* get controller calibration data, and parse it */ 2200 ret = joycon_request_calibration(ctlr); 2201 if (ret) { 2202 /* 2203 * We can function with default calibration, but it may be 2204 * inaccurate. Provide a warning, and continue on. 2205 */ 2206 hid_warn(hdev, "Analog stick positions may be inaccurate\n"); 2207 } 2208 2209 /* get IMU calibration data, and parse it */ 2210 ret = joycon_request_imu_calibration(ctlr); 2211 if (ret) { 2212 /* 2213 * We can function with default calibration, but it may be 2214 * inaccurate. Provide a warning, and continue on. 2215 */ 2216 hid_warn(hdev, "Unable to read IMU calibration data\n"); 2217 } 2218 2219 /* Set the reporting mode to 0x30, which is the full report mode */ 2220 ret = joycon_set_report_mode(ctlr); 2221 if (ret) { 2222 hid_err(hdev, "Failed to set report mode; ret=%d\n", ret); 2223 goto err_mutex; 2224 } 2225 2226 /* Enable rumble */ 2227 ret = joycon_enable_rumble(ctlr); 2228 if (ret) { 2229 hid_err(hdev, "Failed to enable rumble; ret=%d\n", ret); 2230 goto err_mutex; 2231 } 2232 2233 /* Enable the IMU */ 2234 ret = joycon_enable_imu(ctlr); 2235 if (ret) { 2236 hid_err(hdev, "Failed to enable the IMU; ret=%d\n", ret); 2237 goto err_mutex; 2238 } 2239 2240 ret = joycon_read_info(ctlr); 2241 if (ret) { 2242 hid_err(hdev, "Failed to retrieve controller info; ret=%d\n", 2243 ret); 2244 goto err_mutex; 2245 } 2246 2247 mutex_unlock(&ctlr->output_mutex); 2248 2249 /* Initialize the leds */ 2250 ret = joycon_leds_create(ctlr); 2251 if (ret) { 2252 hid_err(hdev, "Failed to create leds; ret=%d\n", ret); 2253 goto err_close; 2254 } 2255 2256 /* Initialize the battery power supply */ 2257 ret = joycon_power_supply_create(ctlr); 2258 if (ret) { 2259 hid_err(hdev, "Failed to create power_supply; ret=%d\n", ret); 2260 goto err_close; 2261 } 2262 2263 ret = joycon_input_create(ctlr); 2264 if (ret) { 2265 hid_err(hdev, "Failed to create input device; ret=%d\n", ret); 2266 goto err_close; 2267 } 2268 2269 ctlr->ctlr_state = JOYCON_CTLR_STATE_READ; 2270 2271 hid_dbg(hdev, "probe - success\n"); 2272 return 0; 2273 2274 err_mutex: 2275 mutex_unlock(&ctlr->output_mutex); 2276 err_close: 2277 hid_hw_close(hdev); 2278 err_stop: 2279 hid_hw_stop(hdev); 2280 err_wq: 2281 destroy_workqueue(ctlr->rumble_queue); 2282 err: 2283 hid_err(hdev, "probe - fail = %d\n", ret); 2284 return ret; 2285 } 2286 2287 static void nintendo_hid_remove(struct hid_device *hdev) 2288 { 2289 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2290 unsigned long flags; 2291 2292 hid_dbg(hdev, "remove\n"); 2293 2294 /* Prevent further attempts at sending subcommands. */ 2295 spin_lock_irqsave(&ctlr->lock, flags); 2296 ctlr->ctlr_state = JOYCON_CTLR_STATE_REMOVED; 2297 spin_unlock_irqrestore(&ctlr->lock, flags); 2298 2299 destroy_workqueue(ctlr->rumble_queue); 2300 2301 hid_hw_close(hdev); 2302 hid_hw_stop(hdev); 2303 } 2304 2305 static const struct hid_device_id nintendo_hid_devices[] = { 2306 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2307 USB_DEVICE_ID_NINTENDO_PROCON) }, 2308 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2309 USB_DEVICE_ID_NINTENDO_PROCON) }, 2310 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2311 USB_DEVICE_ID_NINTENDO_CHRGGRIP) }, 2312 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2313 USB_DEVICE_ID_NINTENDO_JOYCONL) }, 2314 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2315 USB_DEVICE_ID_NINTENDO_JOYCONR) }, 2316 { } 2317 }; 2318 MODULE_DEVICE_TABLE(hid, nintendo_hid_devices); 2319 2320 static struct hid_driver nintendo_hid_driver = { 2321 .name = "nintendo", 2322 .id_table = nintendo_hid_devices, 2323 .probe = nintendo_hid_probe, 2324 .remove = nintendo_hid_remove, 2325 .raw_event = nintendo_hid_event, 2326 }; 2327 module_hid_driver(nintendo_hid_driver); 2328 2329 MODULE_LICENSE("GPL"); 2330 MODULE_AUTHOR("Daniel J. Ogorchock <djogorchock@gmail.com>"); 2331 MODULE_DESCRIPTION("Driver for Nintendo Switch Controllers"); 2332 2333