1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * ZynqMP DisplayPort Driver 4 * 5 * Copyright (C) 2017 - 2020 Xilinx, Inc. 6 * 7 * Authors: 8 * - Hyun Woo Kwon <hyun.kwon@xilinx.com> 9 * - Laurent Pinchart <laurent.pinchart@ideasonboard.com> 10 */ 11 12 #include <drm/drm_atomic_helper.h> 13 #include <drm/drm_connector.h> 14 #include <drm/drm_crtc.h> 15 #include <drm/drm_device.h> 16 #include <drm/drm_dp_helper.h> 17 #include <drm/drm_edid.h> 18 #include <drm/drm_encoder.h> 19 #include <drm/drm_managed.h> 20 #include <drm/drm_modes.h> 21 #include <drm/drm_of.h> 22 #include <drm/drm_probe_helper.h> 23 #include <drm/drm_simple_kms_helper.h> 24 25 #include <linux/clk.h> 26 #include <linux/delay.h> 27 #include <linux/device.h> 28 #include <linux/module.h> 29 #include <linux/platform_device.h> 30 #include <linux/pm_runtime.h> 31 #include <linux/phy/phy.h> 32 #include <linux/reset.h> 33 34 #include "zynqmp_disp.h" 35 #include "zynqmp_dp.h" 36 #include "zynqmp_dpsub.h" 37 38 static uint zynqmp_dp_aux_timeout_ms = 50; 39 module_param_named(aux_timeout_ms, zynqmp_dp_aux_timeout_ms, uint, 0444); 40 MODULE_PARM_DESC(aux_timeout_ms, "DP aux timeout value in msec (default: 50)"); 41 42 /* 43 * Some sink requires a delay after power on request 44 */ 45 static uint zynqmp_dp_power_on_delay_ms = 4; 46 module_param_named(power_on_delay_ms, zynqmp_dp_power_on_delay_ms, uint, 0444); 47 MODULE_PARM_DESC(aux_timeout_ms, "DP power on delay in msec (default: 4)"); 48 49 /* Link configuration registers */ 50 #define ZYNQMP_DP_LINK_BW_SET 0x0 51 #define ZYNQMP_DP_LANE_COUNT_SET 0x4 52 #define ZYNQMP_DP_ENHANCED_FRAME_EN 0x8 53 #define ZYNQMP_DP_TRAINING_PATTERN_SET 0xc 54 #define ZYNQMP_DP_SCRAMBLING_DISABLE 0x14 55 #define ZYNQMP_DP_DOWNSPREAD_CTL 0x18 56 #define ZYNQMP_DP_SOFTWARE_RESET 0x1c 57 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM1 BIT(0) 58 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM2 BIT(1) 59 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM3 BIT(2) 60 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM4 BIT(3) 61 #define ZYNQMP_DP_SOFTWARE_RESET_AUX BIT(7) 62 #define ZYNQMP_DP_SOFTWARE_RESET_ALL (ZYNQMP_DP_SOFTWARE_RESET_STREAM1 | \ 63 ZYNQMP_DP_SOFTWARE_RESET_STREAM2 | \ 64 ZYNQMP_DP_SOFTWARE_RESET_STREAM3 | \ 65 ZYNQMP_DP_SOFTWARE_RESET_STREAM4 | \ 66 ZYNQMP_DP_SOFTWARE_RESET_AUX) 67 68 /* Core enable registers */ 69 #define ZYNQMP_DP_TRANSMITTER_ENABLE 0x80 70 #define ZYNQMP_DP_MAIN_STREAM_ENABLE 0x84 71 #define ZYNQMP_DP_FORCE_SCRAMBLER_RESET 0xc0 72 #define ZYNQMP_DP_VERSION 0xf8 73 #define ZYNQMP_DP_VERSION_MAJOR_MASK GENMASK(31, 24) 74 #define ZYNQMP_DP_VERSION_MAJOR_SHIFT 24 75 #define ZYNQMP_DP_VERSION_MINOR_MASK GENMASK(23, 16) 76 #define ZYNQMP_DP_VERSION_MINOR_SHIFT 16 77 #define ZYNQMP_DP_VERSION_REVISION_MASK GENMASK(15, 12) 78 #define ZYNQMP_DP_VERSION_REVISION_SHIFT 12 79 #define ZYNQMP_DP_VERSION_PATCH_MASK GENMASK(11, 8) 80 #define ZYNQMP_DP_VERSION_PATCH_SHIFT 8 81 #define ZYNQMP_DP_VERSION_INTERNAL_MASK GENMASK(7, 0) 82 #define ZYNQMP_DP_VERSION_INTERNAL_SHIFT 0 83 84 /* Core ID registers */ 85 #define ZYNQMP_DP_CORE_ID 0xfc 86 #define ZYNQMP_DP_CORE_ID_MAJOR_MASK GENMASK(31, 24) 87 #define ZYNQMP_DP_CORE_ID_MAJOR_SHIFT 24 88 #define ZYNQMP_DP_CORE_ID_MINOR_MASK GENMASK(23, 16) 89 #define ZYNQMP_DP_CORE_ID_MINOR_SHIFT 16 90 #define ZYNQMP_DP_CORE_ID_REVISION_MASK GENMASK(15, 8) 91 #define ZYNQMP_DP_CORE_ID_REVISION_SHIFT 8 92 #define ZYNQMP_DP_CORE_ID_DIRECTION GENMASK(1) 93 94 /* AUX channel interface registers */ 95 #define ZYNQMP_DP_AUX_COMMAND 0x100 96 #define ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT 8 97 #define ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY BIT(12) 98 #define ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT 0 99 #define ZYNQMP_DP_AUX_WRITE_FIFO 0x104 100 #define ZYNQMP_DP_AUX_ADDRESS 0x108 101 #define ZYNQMP_DP_AUX_CLK_DIVIDER 0x10c 102 #define ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT 8 103 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE 0x130 104 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD BIT(0) 105 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST BIT(1) 106 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY BIT(2) 107 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT BIT(3) 108 #define ZYNQMP_DP_AUX_REPLY_DATA 0x134 109 #define ZYNQMP_DP_AUX_REPLY_CODE 0x138 110 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK (0) 111 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_NACK BIT(0) 112 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_DEFER BIT(1) 113 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK (0) 114 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_NACK BIT(2) 115 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_DEFER BIT(3) 116 #define ZYNQMP_DP_AUX_REPLY_COUNT 0x13c 117 #define ZYNQMP_DP_REPLY_DATA_COUNT 0x148 118 #define ZYNQMP_DP_REPLY_DATA_COUNT_MASK 0xff 119 #define ZYNQMP_DP_INT_STATUS 0x3a0 120 #define ZYNQMP_DP_INT_MASK 0x3a4 121 #define ZYNQMP_DP_INT_EN 0x3a8 122 #define ZYNQMP_DP_INT_DS 0x3ac 123 #define ZYNQMP_DP_INT_HPD_IRQ BIT(0) 124 #define ZYNQMP_DP_INT_HPD_EVENT BIT(1) 125 #define ZYNQMP_DP_INT_REPLY_RECEIVED BIT(2) 126 #define ZYNQMP_DP_INT_REPLY_TIMEOUT BIT(3) 127 #define ZYNQMP_DP_INT_HPD_PULSE_DET BIT(4) 128 #define ZYNQMP_DP_INT_EXT_PKT_TXD BIT(5) 129 #define ZYNQMP_DP_INT_LIV_ABUF_UNDRFLW BIT(12) 130 #define ZYNQMP_DP_INT_VBLANK_START BIT(13) 131 #define ZYNQMP_DP_INT_PIXEL1_MATCH BIT(14) 132 #define ZYNQMP_DP_INT_PIXEL0_MATCH BIT(15) 133 #define ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK 0x3f0000 134 #define ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK 0xfc00000 135 #define ZYNQMP_DP_INT_CUST_TS_2 BIT(28) 136 #define ZYNQMP_DP_INT_CUST_TS BIT(29) 137 #define ZYNQMP_DP_INT_EXT_VSYNC_TS BIT(30) 138 #define ZYNQMP_DP_INT_VSYNC_TS BIT(31) 139 #define ZYNQMP_DP_INT_ALL (ZYNQMP_DP_INT_HPD_IRQ | \ 140 ZYNQMP_DP_INT_HPD_EVENT | \ 141 ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK | \ 142 ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK) 143 144 /* Main stream attribute registers */ 145 #define ZYNQMP_DP_MAIN_STREAM_HTOTAL 0x180 146 #define ZYNQMP_DP_MAIN_STREAM_VTOTAL 0x184 147 #define ZYNQMP_DP_MAIN_STREAM_POLARITY 0x188 148 #define ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT 0 149 #define ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT 1 150 #define ZYNQMP_DP_MAIN_STREAM_HSWIDTH 0x18c 151 #define ZYNQMP_DP_MAIN_STREAM_VSWIDTH 0x190 152 #define ZYNQMP_DP_MAIN_STREAM_HRES 0x194 153 #define ZYNQMP_DP_MAIN_STREAM_VRES 0x198 154 #define ZYNQMP_DP_MAIN_STREAM_HSTART 0x19c 155 #define ZYNQMP_DP_MAIN_STREAM_VSTART 0x1a0 156 #define ZYNQMP_DP_MAIN_STREAM_MISC0 0x1a4 157 #define ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK BIT(0) 158 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB (0 << 1) 159 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422 (5 << 1) 160 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444 (6 << 1) 161 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK (7 << 1) 162 #define ZYNQMP_DP_MAIN_STREAM_MISC0_DYNAMIC_RANGE BIT(3) 163 #define ZYNQMP_DP_MAIN_STREAM_MISC0_YCBCR_COLR BIT(4) 164 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6 (0 << 5) 165 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8 (1 << 5) 166 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10 (2 << 5) 167 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12 (3 << 5) 168 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16 (4 << 5) 169 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK (7 << 5) 170 #define ZYNQMP_DP_MAIN_STREAM_MISC1 0x1a8 171 #define ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN BIT(7) 172 #define ZYNQMP_DP_MAIN_STREAM_M_VID 0x1ac 173 #define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE 0x1b0 174 #define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF 64 175 #define ZYNQMP_DP_MAIN_STREAM_N_VID 0x1b4 176 #define ZYNQMP_DP_USER_PIX_WIDTH 0x1b8 177 #define ZYNQMP_DP_USER_DATA_COUNT_PER_LANE 0x1bc 178 #define ZYNQMP_DP_MIN_BYTES_PER_TU 0x1c4 179 #define ZYNQMP_DP_FRAC_BYTES_PER_TU 0x1c8 180 #define ZYNQMP_DP_INIT_WAIT 0x1cc 181 182 /* PHY configuration and status registers */ 183 #define ZYNQMP_DP_PHY_RESET 0x200 184 #define ZYNQMP_DP_PHY_RESET_PHY_RESET BIT(0) 185 #define ZYNQMP_DP_PHY_RESET_GTTX_RESET BIT(1) 186 #define ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET BIT(8) 187 #define ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET BIT(9) 188 #define ZYNQMP_DP_PHY_RESET_ALL_RESET (ZYNQMP_DP_PHY_RESET_PHY_RESET | \ 189 ZYNQMP_DP_PHY_RESET_GTTX_RESET | \ 190 ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET | \ 191 ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET) 192 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_0 0x210 193 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_1 0x214 194 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_2 0x218 195 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_3 0x21c 196 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_0 0x220 197 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_1 0x224 198 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_2 0x228 199 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_3 0x22c 200 #define ZYNQMP_DP_PHY_CLOCK_SELECT 0x234 201 #define ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G 0x1 202 #define ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G 0x3 203 #define ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G 0x5 204 #define ZYNQMP_DP_TX_PHY_POWER_DOWN 0x238 205 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_0 BIT(0) 206 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_1 BIT(1) 207 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_2 BIT(2) 208 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_3 BIT(3) 209 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL 0xf 210 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_0 0x23c 211 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_1 0x240 212 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_2 0x244 213 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_3 0x248 214 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_0 0x24c 215 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_1 0x250 216 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_2 0x254 217 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_3 0x258 218 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 0x24c 219 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_1 0x250 220 #define ZYNQMP_DP_PHY_STATUS 0x280 221 #define ZYNQMP_DP_PHY_STATUS_PLL_LOCKED_SHIFT 4 222 #define ZYNQMP_DP_PHY_STATUS_FPGA_PLL_LOCKED BIT(6) 223 224 /* Audio registers */ 225 #define ZYNQMP_DP_TX_AUDIO_CONTROL 0x300 226 #define ZYNQMP_DP_TX_AUDIO_CHANNELS 0x304 227 #define ZYNQMP_DP_TX_AUDIO_INFO_DATA 0x308 228 #define ZYNQMP_DP_TX_M_AUD 0x328 229 #define ZYNQMP_DP_TX_N_AUD 0x32c 230 #define ZYNQMP_DP_TX_AUDIO_EXT_DATA 0x330 231 232 #define ZYNQMP_DP_MAX_LANES 2 233 #define ZYNQMP_MAX_FREQ 3000000 234 235 #define DP_REDUCED_BIT_RATE 162000 236 #define DP_HIGH_BIT_RATE 270000 237 #define DP_HIGH_BIT_RATE2 540000 238 #define DP_MAX_TRAINING_TRIES 5 239 #define DP_V1_2 0x12 240 241 /** 242 * struct zynqmp_dp_link_config - Common link config between source and sink 243 * @max_rate: maximum link rate 244 * @max_lanes: maximum number of lanes 245 */ 246 struct zynqmp_dp_link_config { 247 int max_rate; 248 u8 max_lanes; 249 }; 250 251 /** 252 * struct zynqmp_dp_mode - Configured mode of DisplayPort 253 * @bw_code: code for bandwidth(link rate) 254 * @lane_cnt: number of lanes 255 * @pclock: pixel clock frequency of current mode 256 * @fmt: format identifier string 257 */ 258 struct zynqmp_dp_mode { 259 u8 bw_code; 260 u8 lane_cnt; 261 int pclock; 262 const char *fmt; 263 }; 264 265 /** 266 * struct zynqmp_dp_config - Configuration of DisplayPort from DTS 267 * @misc0: misc0 configuration (per DP v1.2 spec) 268 * @misc1: misc1 configuration (per DP v1.2 spec) 269 * @bpp: bits per pixel 270 */ 271 struct zynqmp_dp_config { 272 u8 misc0; 273 u8 misc1; 274 u8 bpp; 275 }; 276 277 /** 278 * struct zynqmp_dp - Xilinx DisplayPort core 279 * @encoder: the drm encoder structure 280 * @connector: the drm connector structure 281 * @dev: device structure 282 * @dpsub: Display subsystem 283 * @drm: DRM core 284 * @iomem: device I/O memory for register access 285 * @reset: reset controller 286 * @irq: irq 287 * @config: IP core configuration from DTS 288 * @aux: aux channel 289 * @phy: PHY handles for DP lanes 290 * @num_lanes: number of enabled phy lanes 291 * @hpd_work: hot plug detection worker 292 * @status: connection status 293 * @enabled: flag to indicate if the device is enabled 294 * @dpcd: DP configuration data from currently connected sink device 295 * @link_config: common link configuration between IP core and sink device 296 * @mode: current mode between IP core and sink device 297 * @train_set: set of training data 298 */ 299 struct zynqmp_dp { 300 struct drm_encoder encoder; 301 struct drm_connector connector; 302 struct device *dev; 303 struct zynqmp_dpsub *dpsub; 304 struct drm_device *drm; 305 void __iomem *iomem; 306 struct reset_control *reset; 307 int irq; 308 309 struct zynqmp_dp_config config; 310 struct drm_dp_aux aux; 311 struct phy *phy[ZYNQMP_DP_MAX_LANES]; 312 u8 num_lanes; 313 struct delayed_work hpd_work; 314 enum drm_connector_status status; 315 bool enabled; 316 317 u8 dpcd[DP_RECEIVER_CAP_SIZE]; 318 struct zynqmp_dp_link_config link_config; 319 struct zynqmp_dp_mode mode; 320 u8 train_set[ZYNQMP_DP_MAX_LANES]; 321 }; 322 323 static inline struct zynqmp_dp *encoder_to_dp(struct drm_encoder *encoder) 324 { 325 return container_of(encoder, struct zynqmp_dp, encoder); 326 } 327 328 static inline struct zynqmp_dp *connector_to_dp(struct drm_connector *connector) 329 { 330 return container_of(connector, struct zynqmp_dp, connector); 331 } 332 333 static void zynqmp_dp_write(struct zynqmp_dp *dp, int offset, u32 val) 334 { 335 writel(val, dp->iomem + offset); 336 } 337 338 static u32 zynqmp_dp_read(struct zynqmp_dp *dp, int offset) 339 { 340 return readl(dp->iomem + offset); 341 } 342 343 static void zynqmp_dp_clr(struct zynqmp_dp *dp, int offset, u32 clr) 344 { 345 zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) & ~clr); 346 } 347 348 static void zynqmp_dp_set(struct zynqmp_dp *dp, int offset, u32 set) 349 { 350 zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) | set); 351 } 352 353 /* ----------------------------------------------------------------------------- 354 * PHY Handling 355 */ 356 357 #define RST_TIMEOUT_MS 1000 358 359 static int zynqmp_dp_reset(struct zynqmp_dp *dp, bool assert) 360 { 361 unsigned long timeout; 362 363 if (assert) 364 reset_control_assert(dp->reset); 365 else 366 reset_control_deassert(dp->reset); 367 368 /* Wait for the (de)assert to complete. */ 369 timeout = jiffies + msecs_to_jiffies(RST_TIMEOUT_MS); 370 while (!time_after_eq(jiffies, timeout)) { 371 bool status = !!reset_control_status(dp->reset); 372 373 if (assert == status) 374 return 0; 375 376 cpu_relax(); 377 } 378 379 dev_err(dp->dev, "reset %s timeout\n", assert ? "assert" : "deassert"); 380 return -ETIMEDOUT; 381 } 382 383 /** 384 * zynqmp_dp_phy_init - Initialize the phy 385 * @dp: DisplayPort IP core structure 386 * 387 * Initialize the phy. 388 * 389 * Return: 0 if the phy instances are initialized correctly, or the error code 390 * returned from the callee functions. 391 */ 392 static int zynqmp_dp_phy_init(struct zynqmp_dp *dp) 393 { 394 int ret; 395 int i; 396 397 for (i = 0; i < dp->num_lanes; i++) { 398 ret = phy_init(dp->phy[i]); 399 if (ret) { 400 dev_err(dp->dev, "failed to init phy lane %d\n", i); 401 return ret; 402 } 403 } 404 405 ret = zynqmp_dp_reset(dp, false); 406 if (ret < 0) 407 return ret; 408 409 zynqmp_dp_clr(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET); 410 411 /* 412 * Power on lanes in reverse order as only lane 0 waits for the PLL to 413 * lock. 414 */ 415 for (i = dp->num_lanes - 1; i >= 0; i--) { 416 ret = phy_power_on(dp->phy[i]); 417 if (ret) { 418 dev_err(dp->dev, "failed to power on phy lane %d\n", i); 419 return ret; 420 } 421 } 422 423 return 0; 424 } 425 426 /** 427 * zynqmp_dp_phy_exit - Exit the phy 428 * @dp: DisplayPort IP core structure 429 * 430 * Exit the phy. 431 */ 432 static void zynqmp_dp_phy_exit(struct zynqmp_dp *dp) 433 { 434 unsigned int i; 435 int ret; 436 437 for (i = 0; i < dp->num_lanes; i++) { 438 ret = phy_power_off(dp->phy[i]); 439 if (ret) 440 dev_err(dp->dev, "failed to power off phy(%d) %d\n", i, 441 ret); 442 } 443 444 zynqmp_dp_reset(dp, true); 445 446 for (i = 0; i < dp->num_lanes; i++) { 447 ret = phy_exit(dp->phy[i]); 448 if (ret) 449 dev_err(dp->dev, "failed to exit phy(%d) %d\n", i, ret); 450 } 451 } 452 453 /** 454 * zynqmp_dp_phy_probe - Probe the PHYs 455 * @dp: DisplayPort IP core structure 456 * 457 * Probe PHYs for all lanes. Less PHYs may be available than the number of 458 * lanes, which is not considered an error as long as at least one PHY is 459 * found. The caller can check dp->num_lanes to check how many PHYs were found. 460 * 461 * Return: 462 * * 0 - Success 463 * * -ENXIO - No PHY found 464 * * -EPROBE_DEFER - Probe deferral requested 465 * * Other negative value - PHY retrieval failure 466 */ 467 static int zynqmp_dp_phy_probe(struct zynqmp_dp *dp) 468 { 469 unsigned int i; 470 471 for (i = 0; i < ZYNQMP_DP_MAX_LANES; i++) { 472 char phy_name[16]; 473 struct phy *phy; 474 475 snprintf(phy_name, sizeof(phy_name), "dp-phy%d", i); 476 phy = devm_phy_get(dp->dev, phy_name); 477 478 if (IS_ERR(phy)) { 479 switch (PTR_ERR(phy)) { 480 case -ENODEV: 481 if (dp->num_lanes) 482 return 0; 483 484 dev_err(dp->dev, "no PHY found\n"); 485 return -ENXIO; 486 487 case -EPROBE_DEFER: 488 return -EPROBE_DEFER; 489 490 default: 491 dev_err(dp->dev, "failed to get PHY lane %u\n", 492 i); 493 return PTR_ERR(phy); 494 } 495 } 496 497 dp->phy[i] = phy; 498 dp->num_lanes++; 499 } 500 501 return 0; 502 } 503 504 /** 505 * zynqmp_dp_phy_ready - Check if PHY is ready 506 * @dp: DisplayPort IP core structure 507 * 508 * Check if PHY is ready. If PHY is not ready, wait 1ms to check for 100 times. 509 * This amount of delay was suggested by IP designer. 510 * 511 * Return: 0 if PHY is ready, or -ENODEV if PHY is not ready. 512 */ 513 static int zynqmp_dp_phy_ready(struct zynqmp_dp *dp) 514 { 515 u32 i, reg, ready; 516 517 ready = (1 << dp->num_lanes) - 1; 518 519 /* Wait for 100 * 1ms. This should be enough time for PHY to be ready */ 520 for (i = 0; ; i++) { 521 reg = zynqmp_dp_read(dp, ZYNQMP_DP_PHY_STATUS); 522 if ((reg & ready) == ready) 523 return 0; 524 525 if (i == 100) { 526 dev_err(dp->dev, "PHY isn't ready\n"); 527 return -ENODEV; 528 } 529 530 usleep_range(1000, 1100); 531 } 532 533 return 0; 534 } 535 536 /* ----------------------------------------------------------------------------- 537 * DisplayPort Link Training 538 */ 539 540 /** 541 * zynqmp_dp_max_rate - Calculate and return available max pixel clock 542 * @link_rate: link rate (Kilo-bytes / sec) 543 * @lane_num: number of lanes 544 * @bpp: bits per pixel 545 * 546 * Return: max pixel clock (KHz) supported by current link config. 547 */ 548 static inline int zynqmp_dp_max_rate(int link_rate, u8 lane_num, u8 bpp) 549 { 550 return link_rate * lane_num * 8 / bpp; 551 } 552 553 /** 554 * zynqmp_dp_mode_configure - Configure the link values 555 * @dp: DisplayPort IP core structure 556 * @pclock: pixel clock for requested display mode 557 * @current_bw: current link rate 558 * 559 * Find the link configuration values, rate and lane count for requested pixel 560 * clock @pclock. The @pclock is stored in the mode to be used in other 561 * functions later. The returned rate is downshifted from the current rate 562 * @current_bw. 563 * 564 * Return: Current link rate code, or -EINVAL. 565 */ 566 static int zynqmp_dp_mode_configure(struct zynqmp_dp *dp, int pclock, 567 u8 current_bw) 568 { 569 int max_rate = dp->link_config.max_rate; 570 u8 bws[3] = { DP_LINK_BW_1_62, DP_LINK_BW_2_7, DP_LINK_BW_5_4 }; 571 u8 max_lanes = dp->link_config.max_lanes; 572 u8 max_link_rate_code = drm_dp_link_rate_to_bw_code(max_rate); 573 u8 bpp = dp->config.bpp; 574 u8 lane_cnt; 575 s8 i; 576 577 if (current_bw == DP_LINK_BW_1_62) { 578 dev_err(dp->dev, "can't downshift. already lowest link rate\n"); 579 return -EINVAL; 580 } 581 582 for (i = ARRAY_SIZE(bws) - 1; i >= 0; i--) { 583 if (current_bw && bws[i] >= current_bw) 584 continue; 585 586 if (bws[i] <= max_link_rate_code) 587 break; 588 } 589 590 for (lane_cnt = 1; lane_cnt <= max_lanes; lane_cnt <<= 1) { 591 int bw; 592 u32 rate; 593 594 bw = drm_dp_bw_code_to_link_rate(bws[i]); 595 rate = zynqmp_dp_max_rate(bw, lane_cnt, bpp); 596 if (pclock <= rate) { 597 dp->mode.bw_code = bws[i]; 598 dp->mode.lane_cnt = lane_cnt; 599 dp->mode.pclock = pclock; 600 return dp->mode.bw_code; 601 } 602 } 603 604 dev_err(dp->dev, "failed to configure link values\n"); 605 606 return -EINVAL; 607 } 608 609 /** 610 * zynqmp_dp_adjust_train - Adjust train values 611 * @dp: DisplayPort IP core structure 612 * @link_status: link status from sink which contains requested training values 613 */ 614 static void zynqmp_dp_adjust_train(struct zynqmp_dp *dp, 615 u8 link_status[DP_LINK_STATUS_SIZE]) 616 { 617 u8 *train_set = dp->train_set; 618 u8 voltage = 0, preemphasis = 0; 619 u8 i; 620 621 for (i = 0; i < dp->mode.lane_cnt; i++) { 622 u8 v = drm_dp_get_adjust_request_voltage(link_status, i); 623 u8 p = drm_dp_get_adjust_request_pre_emphasis(link_status, i); 624 625 if (v > voltage) 626 voltage = v; 627 628 if (p > preemphasis) 629 preemphasis = p; 630 } 631 632 if (voltage >= DP_TRAIN_VOLTAGE_SWING_LEVEL_3) 633 voltage |= DP_TRAIN_MAX_SWING_REACHED; 634 635 if (preemphasis >= DP_TRAIN_PRE_EMPH_LEVEL_2) 636 preemphasis |= DP_TRAIN_MAX_PRE_EMPHASIS_REACHED; 637 638 for (i = 0; i < dp->mode.lane_cnt; i++) 639 train_set[i] = voltage | preemphasis; 640 } 641 642 /** 643 * zynqmp_dp_update_vs_emph - Update the training values 644 * @dp: DisplayPort IP core structure 645 * 646 * Update the training values based on the request from sink. The mapped values 647 * are predefined, and values(vs, pe, pc) are from the device manual. 648 * 649 * Return: 0 if vs and emph are updated successfully, or the error code returned 650 * by drm_dp_dpcd_write(). 651 */ 652 static int zynqmp_dp_update_vs_emph(struct zynqmp_dp *dp) 653 { 654 unsigned int i; 655 int ret; 656 657 ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, dp->train_set, 658 dp->mode.lane_cnt); 659 if (ret < 0) 660 return ret; 661 662 for (i = 0; i < dp->mode.lane_cnt; i++) { 663 u32 reg = ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 + i * 4; 664 union phy_configure_opts opts = { 0 }; 665 u8 train = dp->train_set[i]; 666 667 opts.dp.voltage[0] = (train & DP_TRAIN_VOLTAGE_SWING_MASK) 668 >> DP_TRAIN_VOLTAGE_SWING_SHIFT; 669 opts.dp.pre[0] = (train & DP_TRAIN_PRE_EMPHASIS_MASK) 670 >> DP_TRAIN_PRE_EMPHASIS_SHIFT; 671 672 phy_configure(dp->phy[i], &opts); 673 674 zynqmp_dp_write(dp, reg, 0x2); 675 } 676 677 return 0; 678 } 679 680 /** 681 * zynqmp_dp_link_train_cr - Train clock recovery 682 * @dp: DisplayPort IP core structure 683 * 684 * Return: 0 if clock recovery train is done successfully, or corresponding 685 * error code. 686 */ 687 static int zynqmp_dp_link_train_cr(struct zynqmp_dp *dp) 688 { 689 u8 link_status[DP_LINK_STATUS_SIZE]; 690 u8 lane_cnt = dp->mode.lane_cnt; 691 u8 vs = 0, tries = 0; 692 u16 max_tries, i; 693 bool cr_done; 694 int ret; 695 696 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, 697 DP_TRAINING_PATTERN_1); 698 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 699 DP_TRAINING_PATTERN_1 | 700 DP_LINK_SCRAMBLING_DISABLE); 701 if (ret < 0) 702 return ret; 703 704 /* 705 * 256 loops should be maximum iterations for 4 lanes and 4 values. 706 * So, This loop should exit before 512 iterations 707 */ 708 for (max_tries = 0; max_tries < 512; max_tries++) { 709 ret = zynqmp_dp_update_vs_emph(dp); 710 if (ret) 711 return ret; 712 713 drm_dp_link_train_clock_recovery_delay(dp->dpcd); 714 ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status); 715 if (ret < 0) 716 return ret; 717 718 cr_done = drm_dp_clock_recovery_ok(link_status, lane_cnt); 719 if (cr_done) 720 break; 721 722 for (i = 0; i < lane_cnt; i++) 723 if (!(dp->train_set[i] & DP_TRAIN_MAX_SWING_REACHED)) 724 break; 725 if (i == lane_cnt) 726 break; 727 728 if ((dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) == vs) 729 tries++; 730 else 731 tries = 0; 732 733 if (tries == DP_MAX_TRAINING_TRIES) 734 break; 735 736 vs = dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK; 737 zynqmp_dp_adjust_train(dp, link_status); 738 } 739 740 if (!cr_done) 741 return -EIO; 742 743 return 0; 744 } 745 746 /** 747 * zynqmp_dp_link_train_ce - Train channel equalization 748 * @dp: DisplayPort IP core structure 749 * 750 * Return: 0 if channel equalization train is done successfully, or 751 * corresponding error code. 752 */ 753 static int zynqmp_dp_link_train_ce(struct zynqmp_dp *dp) 754 { 755 u8 link_status[DP_LINK_STATUS_SIZE]; 756 u8 lane_cnt = dp->mode.lane_cnt; 757 u32 pat, tries; 758 int ret; 759 bool ce_done; 760 761 if (dp->dpcd[DP_DPCD_REV] >= DP_V1_2 && 762 dp->dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED) 763 pat = DP_TRAINING_PATTERN_3; 764 else 765 pat = DP_TRAINING_PATTERN_2; 766 767 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, pat); 768 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 769 pat | DP_LINK_SCRAMBLING_DISABLE); 770 if (ret < 0) 771 return ret; 772 773 for (tries = 0; tries < DP_MAX_TRAINING_TRIES; tries++) { 774 ret = zynqmp_dp_update_vs_emph(dp); 775 if (ret) 776 return ret; 777 778 drm_dp_link_train_channel_eq_delay(dp->dpcd); 779 ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status); 780 if (ret < 0) 781 return ret; 782 783 ce_done = drm_dp_channel_eq_ok(link_status, lane_cnt); 784 if (ce_done) 785 break; 786 787 zynqmp_dp_adjust_train(dp, link_status); 788 } 789 790 if (!ce_done) 791 return -EIO; 792 793 return 0; 794 } 795 796 /** 797 * zynqmp_dp_link_train - Train the link 798 * @dp: DisplayPort IP core structure 799 * 800 * Return: 0 if all trains are done successfully, or corresponding error code. 801 */ 802 static int zynqmp_dp_train(struct zynqmp_dp *dp) 803 { 804 u32 reg; 805 u8 bw_code = dp->mode.bw_code; 806 u8 lane_cnt = dp->mode.lane_cnt; 807 u8 aux_lane_cnt = lane_cnt; 808 bool enhanced; 809 int ret; 810 811 zynqmp_dp_write(dp, ZYNQMP_DP_LANE_COUNT_SET, lane_cnt); 812 enhanced = drm_dp_enhanced_frame_cap(dp->dpcd); 813 if (enhanced) { 814 zynqmp_dp_write(dp, ZYNQMP_DP_ENHANCED_FRAME_EN, 1); 815 aux_lane_cnt |= DP_LANE_COUNT_ENHANCED_FRAME_EN; 816 } 817 818 if (dp->dpcd[3] & 0x1) { 819 zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 1); 820 drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 821 DP_SPREAD_AMP_0_5); 822 } else { 823 zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 0); 824 drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 0); 825 } 826 827 ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, aux_lane_cnt); 828 if (ret < 0) { 829 dev_err(dp->dev, "failed to set lane count\n"); 830 return ret; 831 } 832 833 ret = drm_dp_dpcd_writeb(&dp->aux, DP_MAIN_LINK_CHANNEL_CODING_SET, 834 DP_SET_ANSI_8B10B); 835 if (ret < 0) { 836 dev_err(dp->dev, "failed to set ANSI 8B/10B encoding\n"); 837 return ret; 838 } 839 840 ret = drm_dp_dpcd_writeb(&dp->aux, DP_LINK_BW_SET, bw_code); 841 if (ret < 0) { 842 dev_err(dp->dev, "failed to set DP bandwidth\n"); 843 return ret; 844 } 845 846 zynqmp_dp_write(dp, ZYNQMP_DP_LINK_BW_SET, bw_code); 847 switch (bw_code) { 848 case DP_LINK_BW_1_62: 849 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G; 850 break; 851 case DP_LINK_BW_2_7: 852 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G; 853 break; 854 case DP_LINK_BW_5_4: 855 default: 856 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G; 857 break; 858 } 859 860 zynqmp_dp_write(dp, ZYNQMP_DP_PHY_CLOCK_SELECT, reg); 861 ret = zynqmp_dp_phy_ready(dp); 862 if (ret < 0) 863 return ret; 864 865 zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 1); 866 memset(dp->train_set, 0, 4); 867 ret = zynqmp_dp_link_train_cr(dp); 868 if (ret) 869 return ret; 870 871 ret = zynqmp_dp_link_train_ce(dp); 872 if (ret) 873 return ret; 874 875 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 876 DP_TRAINING_PATTERN_DISABLE); 877 if (ret < 0) { 878 dev_err(dp->dev, "failed to disable training pattern\n"); 879 return ret; 880 } 881 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, 882 DP_TRAINING_PATTERN_DISABLE); 883 884 zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 0); 885 886 return 0; 887 } 888 889 /** 890 * zynqmp_dp_train_loop - Downshift the link rate during training 891 * @dp: DisplayPort IP core structure 892 * 893 * Train the link by downshifting the link rate if training is not successful. 894 */ 895 static void zynqmp_dp_train_loop(struct zynqmp_dp *dp) 896 { 897 struct zynqmp_dp_mode *mode = &dp->mode; 898 u8 bw = mode->bw_code; 899 int ret; 900 901 do { 902 if (dp->status == connector_status_disconnected || 903 !dp->enabled) 904 return; 905 906 ret = zynqmp_dp_train(dp); 907 if (!ret) 908 return; 909 910 ret = zynqmp_dp_mode_configure(dp, mode->pclock, bw); 911 if (ret < 0) 912 goto err_out; 913 914 bw = ret; 915 } while (bw >= DP_LINK_BW_1_62); 916 917 err_out: 918 dev_err(dp->dev, "failed to train the DP link\n"); 919 } 920 921 /* ----------------------------------------------------------------------------- 922 * DisplayPort AUX 923 */ 924 925 #define AUX_READ_BIT 0x1 926 927 /** 928 * zynqmp_dp_aux_cmd_submit - Submit aux command 929 * @dp: DisplayPort IP core structure 930 * @cmd: aux command 931 * @addr: aux address 932 * @buf: buffer for command data 933 * @bytes: number of bytes for @buf 934 * @reply: reply code to be returned 935 * 936 * Submit an aux command. All aux related commands, native or i2c aux 937 * read/write, are submitted through this function. The function is mapped to 938 * the transfer function of struct drm_dp_aux. This function involves in 939 * multiple register reads/writes, thus synchronization is needed, and it is 940 * done by drm_dp_helper using @hw_mutex. The calling thread goes into sleep 941 * if there's no immediate reply to the command submission. The reply code is 942 * returned at @reply if @reply != NULL. 943 * 944 * Return: 0 if the command is submitted properly, or corresponding error code: 945 * -EBUSY when there is any request already being processed 946 * -ETIMEDOUT when receiving reply is timed out 947 * -EIO when received bytes are less than requested 948 */ 949 static int zynqmp_dp_aux_cmd_submit(struct zynqmp_dp *dp, u32 cmd, u16 addr, 950 u8 *buf, u8 bytes, u8 *reply) 951 { 952 bool is_read = (cmd & AUX_READ_BIT) ? true : false; 953 u32 reg, i; 954 955 reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 956 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST) 957 return -EBUSY; 958 959 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_ADDRESS, addr); 960 if (!is_read) 961 for (i = 0; i < bytes; i++) 962 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_WRITE_FIFO, 963 buf[i]); 964 965 reg = cmd << ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT; 966 if (!buf || !bytes) 967 reg |= ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY; 968 else 969 reg |= (bytes - 1) << ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT; 970 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_COMMAND, reg); 971 972 /* Wait for reply to be delivered upto 2ms */ 973 for (i = 0; ; i++) { 974 reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 975 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY) 976 break; 977 978 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT || 979 i == 2) 980 return -ETIMEDOUT; 981 982 usleep_range(1000, 1100); 983 } 984 985 reg = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_CODE); 986 if (reply) 987 *reply = reg; 988 989 if (is_read && 990 (reg == ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK || 991 reg == ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK)) { 992 reg = zynqmp_dp_read(dp, ZYNQMP_DP_REPLY_DATA_COUNT); 993 if ((reg & ZYNQMP_DP_REPLY_DATA_COUNT_MASK) != bytes) 994 return -EIO; 995 996 for (i = 0; i < bytes; i++) 997 buf[i] = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_DATA); 998 } 999 1000 return 0; 1001 } 1002 1003 static ssize_t 1004 zynqmp_dp_aux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg) 1005 { 1006 struct zynqmp_dp *dp = container_of(aux, struct zynqmp_dp, aux); 1007 int ret; 1008 unsigned int i, iter; 1009 1010 /* Number of loops = timeout in msec / aux delay (400 usec) */ 1011 iter = zynqmp_dp_aux_timeout_ms * 1000 / 400; 1012 iter = iter ? iter : 1; 1013 1014 for (i = 0; i < iter; i++) { 1015 ret = zynqmp_dp_aux_cmd_submit(dp, msg->request, msg->address, 1016 msg->buffer, msg->size, 1017 &msg->reply); 1018 if (!ret) { 1019 dev_dbg(dp->dev, "aux %d retries\n", i); 1020 return msg->size; 1021 } 1022 1023 if (dp->status == connector_status_disconnected) { 1024 dev_dbg(dp->dev, "no connected aux device\n"); 1025 return -ENODEV; 1026 } 1027 1028 usleep_range(400, 500); 1029 } 1030 1031 dev_dbg(dp->dev, "failed to do aux transfer (%d)\n", ret); 1032 1033 return ret; 1034 } 1035 1036 /** 1037 * zynqmp_dp_aux_init - Initialize and register the DP AUX 1038 * @dp: DisplayPort IP core structure 1039 * 1040 * Program the AUX clock divider and filter and register the DP AUX adapter. 1041 * 1042 * Return: 0 on success, error value otherwise 1043 */ 1044 static int zynqmp_dp_aux_init(struct zynqmp_dp *dp) 1045 { 1046 unsigned long rate; 1047 unsigned int w; 1048 1049 /* 1050 * The AUX_SIGNAL_WIDTH_FILTER is the number of APB clock cycles 1051 * corresponding to the AUX pulse. Allowable values are 8, 16, 24, 32, 1052 * 40 and 48. The AUX pulse width must be between 0.4µs and 0.6µs, 1053 * compute the w / 8 value corresponding to 0.4µs rounded up, and make 1054 * sure it stays below 0.6µs and within the allowable values. 1055 */ 1056 rate = clk_get_rate(dp->dpsub->apb_clk); 1057 w = DIV_ROUND_UP(4 * rate, 1000 * 1000 * 10 * 8) * 8; 1058 if (w > 6 * rate / (1000 * 1000 * 10) || w > 48) { 1059 dev_err(dp->dev, "aclk frequency too high\n"); 1060 return -EINVAL; 1061 } 1062 1063 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_CLK_DIVIDER, 1064 (w << ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT) | 1065 (rate / (1000 * 1000))); 1066 1067 dp->aux.name = "ZynqMP DP AUX"; 1068 dp->aux.dev = dp->dev; 1069 dp->aux.transfer = zynqmp_dp_aux_transfer; 1070 1071 return drm_dp_aux_register(&dp->aux); 1072 } 1073 1074 /** 1075 * zynqmp_dp_aux_cleanup - Cleanup the DP AUX 1076 * @dp: DisplayPort IP core structure 1077 * 1078 * Unregister the DP AUX adapter. 1079 */ 1080 static void zynqmp_dp_aux_cleanup(struct zynqmp_dp *dp) 1081 { 1082 drm_dp_aux_unregister(&dp->aux); 1083 } 1084 1085 /* ----------------------------------------------------------------------------- 1086 * DisplayPort Generic Support 1087 */ 1088 1089 /** 1090 * zynqmp_dp_update_misc - Write the misc registers 1091 * @dp: DisplayPort IP core structure 1092 * 1093 * The misc register values are stored in the structure, and this 1094 * function applies the values into the registers. 1095 */ 1096 static void zynqmp_dp_update_misc(struct zynqmp_dp *dp) 1097 { 1098 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC0, dp->config.misc0); 1099 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC1, dp->config.misc1); 1100 } 1101 1102 /** 1103 * zynqmp_dp_set_format - Set the input format 1104 * @dp: DisplayPort IP core structure 1105 * @format: input format 1106 * @bpc: bits per component 1107 * 1108 * Update misc register values based on input @format and @bpc. 1109 * 1110 * Return: 0 on success, or -EINVAL. 1111 */ 1112 static int zynqmp_dp_set_format(struct zynqmp_dp *dp, 1113 enum zynqmp_dpsub_format format, 1114 unsigned int bpc) 1115 { 1116 static const struct drm_display_info *display; 1117 struct zynqmp_dp_config *config = &dp->config; 1118 unsigned int num_colors; 1119 1120 config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK; 1121 config->misc1 &= ~ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN; 1122 1123 switch (format) { 1124 case ZYNQMP_DPSUB_FORMAT_RGB: 1125 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB; 1126 num_colors = 3; 1127 break; 1128 1129 case ZYNQMP_DPSUB_FORMAT_YCRCB444: 1130 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444; 1131 num_colors = 3; 1132 break; 1133 1134 case ZYNQMP_DPSUB_FORMAT_YCRCB422: 1135 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422; 1136 num_colors = 2; 1137 break; 1138 1139 case ZYNQMP_DPSUB_FORMAT_YONLY: 1140 config->misc1 |= ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN; 1141 num_colors = 1; 1142 break; 1143 1144 default: 1145 dev_err(dp->dev, "Invalid colormetry in DT\n"); 1146 return -EINVAL; 1147 } 1148 1149 display = &dp->connector.display_info; 1150 if (display->bpc && bpc > display->bpc) { 1151 dev_warn(dp->dev, 1152 "downgrading requested %ubpc to display limit %ubpc\n", 1153 bpc, display->bpc); 1154 bpc = display->bpc; 1155 } 1156 1157 config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK; 1158 1159 switch (bpc) { 1160 case 6: 1161 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6; 1162 break; 1163 case 8: 1164 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8; 1165 break; 1166 case 10: 1167 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10; 1168 break; 1169 case 12: 1170 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12; 1171 break; 1172 case 16: 1173 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16; 1174 break; 1175 default: 1176 dev_warn(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n", 1177 bpc); 1178 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8; 1179 bpc = 8; 1180 break; 1181 } 1182 1183 /* Update the current bpp based on the format. */ 1184 config->bpp = bpc * num_colors; 1185 1186 return 0; 1187 } 1188 1189 /** 1190 * zynqmp_dp_encoder_mode_set_transfer_unit - Set the transfer unit values 1191 * @dp: DisplayPort IP core structure 1192 * @mode: requested display mode 1193 * 1194 * Set the transfer unit, and calculate all transfer unit size related values. 1195 * Calculation is based on DP and IP core specification. 1196 */ 1197 static void 1198 zynqmp_dp_encoder_mode_set_transfer_unit(struct zynqmp_dp *dp, 1199 struct drm_display_mode *mode) 1200 { 1201 u32 tu = ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF; 1202 u32 bw, vid_kbytes, avg_bytes_per_tu, init_wait; 1203 1204 /* Use the max transfer unit size (default) */ 1205 zynqmp_dp_write(dp, ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE, tu); 1206 1207 vid_kbytes = mode->clock * (dp->config.bpp / 8); 1208 bw = drm_dp_bw_code_to_link_rate(dp->mode.bw_code); 1209 avg_bytes_per_tu = vid_kbytes * tu / (dp->mode.lane_cnt * bw / 1000); 1210 zynqmp_dp_write(dp, ZYNQMP_DP_MIN_BYTES_PER_TU, 1211 avg_bytes_per_tu / 1000); 1212 zynqmp_dp_write(dp, ZYNQMP_DP_FRAC_BYTES_PER_TU, 1213 avg_bytes_per_tu % 1000); 1214 1215 /* Configure the initial wait cycle based on transfer unit size */ 1216 if (tu < (avg_bytes_per_tu / 1000)) 1217 init_wait = 0; 1218 else if ((avg_bytes_per_tu / 1000) <= 4) 1219 init_wait = tu; 1220 else 1221 init_wait = tu - avg_bytes_per_tu / 1000; 1222 1223 zynqmp_dp_write(dp, ZYNQMP_DP_INIT_WAIT, init_wait); 1224 } 1225 1226 /** 1227 * zynqmp_dp_encoder_mode_set_stream - Configure the main stream 1228 * @dp: DisplayPort IP core structure 1229 * @mode: requested display mode 1230 * 1231 * Configure the main stream based on the requested mode @mode. Calculation is 1232 * based on IP core specification. 1233 */ 1234 static void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp, 1235 const struct drm_display_mode *mode) 1236 { 1237 u8 lane_cnt = dp->mode.lane_cnt; 1238 u32 reg, wpl; 1239 unsigned int rate; 1240 1241 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HTOTAL, mode->htotal); 1242 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VTOTAL, mode->vtotal); 1243 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_POLARITY, 1244 (!!(mode->flags & DRM_MODE_FLAG_PVSYNC) << 1245 ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT) | 1246 (!!(mode->flags & DRM_MODE_FLAG_PHSYNC) << 1247 ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT)); 1248 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSWIDTH, 1249 mode->hsync_end - mode->hsync_start); 1250 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSWIDTH, 1251 mode->vsync_end - mode->vsync_start); 1252 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HRES, mode->hdisplay); 1253 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VRES, mode->vdisplay); 1254 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSTART, 1255 mode->htotal - mode->hsync_start); 1256 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSTART, 1257 mode->vtotal - mode->vsync_start); 1258 1259 /* In synchronous mode, set the diviers */ 1260 if (dp->config.misc0 & ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK) { 1261 reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code); 1262 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_N_VID, reg); 1263 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_M_VID, mode->clock); 1264 rate = zynqmp_disp_get_audio_clk_rate(dp->dpsub->disp); 1265 if (rate) { 1266 dev_dbg(dp->dev, "Audio rate: %d\n", rate / 512); 1267 zynqmp_dp_write(dp, ZYNQMP_DP_TX_N_AUD, reg); 1268 zynqmp_dp_write(dp, ZYNQMP_DP_TX_M_AUD, rate / 1000); 1269 } 1270 } 1271 1272 /* Only 2 channel audio is supported now */ 1273 if (zynqmp_disp_audio_enabled(dp->dpsub->disp)) 1274 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CHANNELS, 1); 1275 1276 zynqmp_dp_write(dp, ZYNQMP_DP_USER_PIX_WIDTH, 1); 1277 1278 /* Translate to the native 16 bit datapath based on IP core spec */ 1279 wpl = (mode->hdisplay * dp->config.bpp + 15) / 16; 1280 reg = wpl + wpl % lane_cnt - lane_cnt; 1281 zynqmp_dp_write(dp, ZYNQMP_DP_USER_DATA_COUNT_PER_LANE, reg); 1282 } 1283 1284 /* ----------------------------------------------------------------------------- 1285 * DRM Connector 1286 */ 1287 1288 static enum drm_connector_status 1289 zynqmp_dp_connector_detect(struct drm_connector *connector, bool force) 1290 { 1291 struct zynqmp_dp *dp = connector_to_dp(connector); 1292 struct zynqmp_dp_link_config *link_config = &dp->link_config; 1293 u32 state, i; 1294 int ret; 1295 1296 /* 1297 * This is from heuristic. It takes some delay (ex, 100 ~ 500 msec) to 1298 * get the HPD signal with some monitors. 1299 */ 1300 for (i = 0; i < 10; i++) { 1301 state = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 1302 if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD) 1303 break; 1304 msleep(100); 1305 } 1306 1307 if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD) { 1308 ret = drm_dp_dpcd_read(&dp->aux, 0x0, dp->dpcd, 1309 sizeof(dp->dpcd)); 1310 if (ret < 0) { 1311 dev_dbg(dp->dev, "DPCD read failes"); 1312 goto disconnected; 1313 } 1314 1315 link_config->max_rate = min_t(int, 1316 drm_dp_max_link_rate(dp->dpcd), 1317 DP_HIGH_BIT_RATE2); 1318 link_config->max_lanes = min_t(u8, 1319 drm_dp_max_lane_count(dp->dpcd), 1320 dp->num_lanes); 1321 1322 dp->status = connector_status_connected; 1323 return connector_status_connected; 1324 } 1325 1326 disconnected: 1327 dp->status = connector_status_disconnected; 1328 return connector_status_disconnected; 1329 } 1330 1331 static int zynqmp_dp_connector_get_modes(struct drm_connector *connector) 1332 { 1333 struct zynqmp_dp *dp = connector_to_dp(connector); 1334 struct edid *edid; 1335 int ret; 1336 1337 edid = drm_get_edid(connector, &dp->aux.ddc); 1338 if (!edid) 1339 return 0; 1340 1341 drm_connector_update_edid_property(connector, edid); 1342 ret = drm_add_edid_modes(connector, edid); 1343 kfree(edid); 1344 1345 return ret; 1346 } 1347 1348 static struct drm_encoder * 1349 zynqmp_dp_connector_best_encoder(struct drm_connector *connector) 1350 { 1351 struct zynqmp_dp *dp = connector_to_dp(connector); 1352 1353 return &dp->encoder; 1354 } 1355 1356 static int zynqmp_dp_connector_mode_valid(struct drm_connector *connector, 1357 struct drm_display_mode *mode) 1358 { 1359 struct zynqmp_dp *dp = connector_to_dp(connector); 1360 u8 max_lanes = dp->link_config.max_lanes; 1361 u8 bpp = dp->config.bpp; 1362 int max_rate = dp->link_config.max_rate; 1363 int rate; 1364 1365 if (mode->clock > ZYNQMP_MAX_FREQ) { 1366 dev_dbg(dp->dev, "filtered the mode, %s,for high pixel rate\n", 1367 mode->name); 1368 drm_mode_debug_printmodeline(mode); 1369 return MODE_CLOCK_HIGH; 1370 } 1371 1372 /* Check with link rate and lane count */ 1373 rate = zynqmp_dp_max_rate(max_rate, max_lanes, bpp); 1374 if (mode->clock > rate) { 1375 dev_dbg(dp->dev, "filtered the mode, %s,for high pixel rate\n", 1376 mode->name); 1377 drm_mode_debug_printmodeline(mode); 1378 return MODE_CLOCK_HIGH; 1379 } 1380 1381 return MODE_OK; 1382 } 1383 1384 static const struct drm_connector_funcs zynqmp_dp_connector_funcs = { 1385 .detect = zynqmp_dp_connector_detect, 1386 .fill_modes = drm_helper_probe_single_connector_modes, 1387 .destroy = drm_connector_cleanup, 1388 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 1389 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1390 .reset = drm_atomic_helper_connector_reset, 1391 }; 1392 1393 static const struct drm_connector_helper_funcs 1394 zynqmp_dp_connector_helper_funcs = { 1395 .get_modes = zynqmp_dp_connector_get_modes, 1396 .best_encoder = zynqmp_dp_connector_best_encoder, 1397 .mode_valid = zynqmp_dp_connector_mode_valid, 1398 }; 1399 1400 /* ----------------------------------------------------------------------------- 1401 * DRM Encoder 1402 */ 1403 1404 static void zynqmp_dp_encoder_enable(struct drm_encoder *encoder) 1405 { 1406 struct zynqmp_dp *dp = encoder_to_dp(encoder); 1407 unsigned int i; 1408 int ret = 0; 1409 1410 pm_runtime_get_sync(dp->dev); 1411 dp->enabled = true; 1412 zynqmp_dp_update_misc(dp); 1413 if (zynqmp_disp_audio_enabled(dp->dpsub->disp)) 1414 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 1); 1415 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 0); 1416 if (dp->status == connector_status_connected) { 1417 for (i = 0; i < 3; i++) { 1418 ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, 1419 DP_SET_POWER_D0); 1420 if (ret == 1) 1421 break; 1422 usleep_range(300, 500); 1423 } 1424 /* Some monitors take time to wake up properly */ 1425 msleep(zynqmp_dp_power_on_delay_ms); 1426 } 1427 if (ret != 1) 1428 dev_dbg(dp->dev, "DP aux failed\n"); 1429 else 1430 zynqmp_dp_train_loop(dp); 1431 zynqmp_dp_write(dp, ZYNQMP_DP_SOFTWARE_RESET, 1432 ZYNQMP_DP_SOFTWARE_RESET_ALL); 1433 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 1); 1434 } 1435 1436 static void zynqmp_dp_encoder_disable(struct drm_encoder *encoder) 1437 { 1438 struct zynqmp_dp *dp = encoder_to_dp(encoder); 1439 1440 dp->enabled = false; 1441 cancel_delayed_work(&dp->hpd_work); 1442 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 0); 1443 drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D3); 1444 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 1445 ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL); 1446 if (zynqmp_disp_audio_enabled(dp->dpsub->disp)) 1447 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 0); 1448 pm_runtime_put_sync(dp->dev); 1449 } 1450 1451 static void 1452 zynqmp_dp_encoder_atomic_mode_set(struct drm_encoder *encoder, 1453 struct drm_crtc_state *crtc_state, 1454 struct drm_connector_state *connector_state) 1455 { 1456 struct zynqmp_dp *dp = encoder_to_dp(encoder); 1457 struct drm_display_mode *mode = &crtc_state->mode; 1458 struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode; 1459 u8 max_lanes = dp->link_config.max_lanes; 1460 u8 bpp = dp->config.bpp; 1461 int rate, max_rate = dp->link_config.max_rate; 1462 int ret; 1463 1464 zynqmp_dp_set_format(dp, ZYNQMP_DPSUB_FORMAT_RGB, 8); 1465 1466 /* Check again as bpp or format might have been chagned */ 1467 rate = zynqmp_dp_max_rate(max_rate, max_lanes, bpp); 1468 if (mode->clock > rate) { 1469 dev_err(dp->dev, "the mode, %s,has too high pixel rate\n", 1470 mode->name); 1471 drm_mode_debug_printmodeline(mode); 1472 } 1473 1474 ret = zynqmp_dp_mode_configure(dp, adjusted_mode->clock, 0); 1475 if (ret < 0) 1476 return; 1477 1478 zynqmp_dp_encoder_mode_set_transfer_unit(dp, adjusted_mode); 1479 zynqmp_dp_encoder_mode_set_stream(dp, adjusted_mode); 1480 } 1481 1482 #define ZYNQMP_DP_MIN_H_BACKPORCH 20 1483 1484 static int 1485 zynqmp_dp_encoder_atomic_check(struct drm_encoder *encoder, 1486 struct drm_crtc_state *crtc_state, 1487 struct drm_connector_state *conn_state) 1488 { 1489 struct drm_display_mode *mode = &crtc_state->mode; 1490 struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode; 1491 int diff = mode->htotal - mode->hsync_end; 1492 1493 /* 1494 * ZynqMP DP requires horizontal backporch to be greater than 12. 1495 * This limitation may not be compatible with the sink device. 1496 */ 1497 if (diff < ZYNQMP_DP_MIN_H_BACKPORCH) { 1498 int vrefresh = (adjusted_mode->clock * 1000) / 1499 (adjusted_mode->vtotal * adjusted_mode->htotal); 1500 1501 dev_dbg(encoder->dev->dev, "hbackporch adjusted: %d to %d", 1502 diff, ZYNQMP_DP_MIN_H_BACKPORCH - diff); 1503 diff = ZYNQMP_DP_MIN_H_BACKPORCH - diff; 1504 adjusted_mode->htotal += diff; 1505 adjusted_mode->clock = adjusted_mode->vtotal * 1506 adjusted_mode->htotal * vrefresh / 1000; 1507 } 1508 1509 return 0; 1510 } 1511 1512 static const struct drm_encoder_helper_funcs zynqmp_dp_encoder_helper_funcs = { 1513 .enable = zynqmp_dp_encoder_enable, 1514 .disable = zynqmp_dp_encoder_disable, 1515 .atomic_mode_set = zynqmp_dp_encoder_atomic_mode_set, 1516 .atomic_check = zynqmp_dp_encoder_atomic_check, 1517 }; 1518 1519 /* ----------------------------------------------------------------------------- 1520 * Interrupt Handling 1521 */ 1522 1523 /** 1524 * zynqmp_dp_enable_vblank - Enable vblank 1525 * @dp: DisplayPort IP core structure 1526 * 1527 * Enable vblank interrupt 1528 */ 1529 void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp) 1530 { 1531 zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_VBLANK_START); 1532 } 1533 1534 /** 1535 * zynqmp_dp_disable_vblank - Disable vblank 1536 * @dp: DisplayPort IP core structure 1537 * 1538 * Disable vblank interrupt 1539 */ 1540 void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp) 1541 { 1542 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_VBLANK_START); 1543 } 1544 1545 static void zynqmp_dp_hpd_work_func(struct work_struct *work) 1546 { 1547 struct zynqmp_dp *dp; 1548 1549 dp = container_of(work, struct zynqmp_dp, hpd_work.work); 1550 1551 if (dp->drm) 1552 drm_helper_hpd_irq_event(dp->drm); 1553 } 1554 1555 static irqreturn_t zynqmp_dp_irq_handler(int irq, void *data) 1556 { 1557 struct zynqmp_dp *dp = (struct zynqmp_dp *)data; 1558 u32 status, mask; 1559 1560 status = zynqmp_dp_read(dp, ZYNQMP_DP_INT_STATUS); 1561 mask = zynqmp_dp_read(dp, ZYNQMP_DP_INT_MASK); 1562 if (!(status & ~mask)) 1563 return IRQ_NONE; 1564 1565 /* dbg for diagnostic, but not much that the driver can do */ 1566 if (status & ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK) 1567 dev_dbg_ratelimited(dp->dev, "underflow interrupt\n"); 1568 if (status & ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK) 1569 dev_dbg_ratelimited(dp->dev, "overflow interrupt\n"); 1570 1571 zynqmp_dp_write(dp, ZYNQMP_DP_INT_STATUS, status); 1572 1573 if (status & ZYNQMP_DP_INT_VBLANK_START) 1574 zynqmp_disp_handle_vblank(dp->dpsub->disp); 1575 1576 if (status & ZYNQMP_DP_INT_HPD_EVENT) 1577 schedule_delayed_work(&dp->hpd_work, 0); 1578 1579 if (status & ZYNQMP_DP_INT_HPD_IRQ) { 1580 int ret; 1581 u8 status[DP_LINK_STATUS_SIZE + 2]; 1582 1583 ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, status, 1584 DP_LINK_STATUS_SIZE + 2); 1585 if (ret < 0) 1586 goto handled; 1587 1588 if (status[4] & DP_LINK_STATUS_UPDATED || 1589 !drm_dp_clock_recovery_ok(&status[2], dp->mode.lane_cnt) || 1590 !drm_dp_channel_eq_ok(&status[2], dp->mode.lane_cnt)) { 1591 zynqmp_dp_train_loop(dp); 1592 } 1593 } 1594 1595 handled: 1596 return IRQ_HANDLED; 1597 } 1598 1599 /* ----------------------------------------------------------------------------- 1600 * Initialization & Cleanup 1601 */ 1602 1603 int zynqmp_dp_drm_init(struct zynqmp_dpsub *dpsub) 1604 { 1605 struct zynqmp_dp *dp = dpsub->dp; 1606 struct drm_encoder *encoder = &dp->encoder; 1607 struct drm_connector *connector = &dp->connector; 1608 int ret; 1609 1610 dp->config.misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK; 1611 zynqmp_dp_set_format(dp, ZYNQMP_DPSUB_FORMAT_RGB, 8); 1612 1613 /* Create the DRM encoder and connector. */ 1614 encoder->possible_crtcs |= zynqmp_disp_get_crtc_mask(dpsub->disp); 1615 drm_simple_encoder_init(dp->drm, encoder, DRM_MODE_ENCODER_TMDS); 1616 drm_encoder_helper_add(encoder, &zynqmp_dp_encoder_helper_funcs); 1617 1618 connector->polled = DRM_CONNECTOR_POLL_HPD; 1619 ret = drm_connector_init(encoder->dev, connector, 1620 &zynqmp_dp_connector_funcs, 1621 DRM_MODE_CONNECTOR_DisplayPort); 1622 if (ret) { 1623 dev_err(dp->dev, "failed to create the DRM connector\n"); 1624 return ret; 1625 } 1626 1627 drm_connector_helper_add(connector, &zynqmp_dp_connector_helper_funcs); 1628 drm_connector_register(connector); 1629 drm_connector_attach_encoder(connector, encoder); 1630 1631 /* Initialize and register the AUX adapter. */ 1632 ret = zynqmp_dp_aux_init(dp); 1633 if (ret) { 1634 dev_err(dp->dev, "failed to initialize DP aux\n"); 1635 return ret; 1636 } 1637 1638 /* Now that initialisation is complete, enable interrupts. */ 1639 zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_ALL); 1640 1641 return 0; 1642 } 1643 1644 int zynqmp_dp_probe(struct zynqmp_dpsub *dpsub, struct drm_device *drm) 1645 { 1646 struct platform_device *pdev = to_platform_device(dpsub->dev); 1647 struct zynqmp_dp *dp; 1648 struct resource *res; 1649 int ret; 1650 1651 dp = drmm_kzalloc(drm, sizeof(*dp), GFP_KERNEL); 1652 if (!dp) 1653 return -ENOMEM; 1654 1655 dp->dev = &pdev->dev; 1656 dp->dpsub = dpsub; 1657 dp->status = connector_status_disconnected; 1658 dp->drm = drm; 1659 1660 INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func); 1661 1662 dpsub->dp = dp; 1663 1664 /* Acquire all resources (IOMEM, IRQ and PHYs). */ 1665 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp"); 1666 dp->iomem = devm_ioremap_resource(dp->dev, res); 1667 if (IS_ERR(dp->iomem)) 1668 return PTR_ERR(dp->iomem); 1669 1670 dp->irq = platform_get_irq(pdev, 0); 1671 if (dp->irq < 0) 1672 return dp->irq; 1673 1674 dp->reset = devm_reset_control_get(dp->dev, NULL); 1675 if (IS_ERR(dp->reset)) { 1676 if (PTR_ERR(dp->reset) != -EPROBE_DEFER) 1677 dev_err(dp->dev, "failed to get reset: %ld\n", 1678 PTR_ERR(dp->reset)); 1679 return PTR_ERR(dp->reset); 1680 } 1681 1682 ret = zynqmp_dp_phy_probe(dp); 1683 if (ret) 1684 return ret; 1685 1686 /* Initialize the hardware. */ 1687 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 1688 ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL); 1689 zynqmp_dp_set(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET); 1690 zynqmp_dp_write(dp, ZYNQMP_DP_FORCE_SCRAMBLER_RESET, 1); 1691 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0); 1692 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff); 1693 1694 ret = zynqmp_dp_phy_init(dp); 1695 if (ret) 1696 return ret; 1697 1698 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 1); 1699 1700 /* 1701 * Now that the hardware is initialized and won't generate spurious 1702 * interrupts, request the IRQ. 1703 */ 1704 ret = devm_request_threaded_irq(dp->dev, dp->irq, NULL, 1705 zynqmp_dp_irq_handler, IRQF_ONESHOT, 1706 dev_name(dp->dev), dp); 1707 if (ret < 0) 1708 goto error; 1709 1710 dev_dbg(dp->dev, "ZynqMP DisplayPort Tx probed with %u lanes\n", 1711 dp->num_lanes); 1712 1713 return 0; 1714 1715 error: 1716 zynqmp_dp_phy_exit(dp); 1717 return ret; 1718 } 1719 1720 void zynqmp_dp_remove(struct zynqmp_dpsub *dpsub) 1721 { 1722 struct zynqmp_dp *dp = dpsub->dp; 1723 1724 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_ALL); 1725 disable_irq(dp->irq); 1726 1727 cancel_delayed_work_sync(&dp->hpd_work); 1728 zynqmp_dp_aux_cleanup(dp); 1729 1730 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0); 1731 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff); 1732 1733 zynqmp_dp_phy_exit(dp); 1734 } 1735