1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * ZynqMP DisplayPort Driver 4 * 5 * Copyright (C) 2017 - 2020 Xilinx, Inc. 6 * 7 * Authors: 8 * - Hyun Woo Kwon <hyun.kwon@xilinx.com> 9 * - Laurent Pinchart <laurent.pinchart@ideasonboard.com> 10 */ 11 12 #include <drm/display/drm_dp_helper.h> 13 #include <drm/drm_atomic_helper.h> 14 #include <drm/drm_crtc.h> 15 #include <drm/drm_device.h> 16 #include <drm/drm_edid.h> 17 #include <drm/drm_fourcc.h> 18 #include <drm/drm_modes.h> 19 #include <drm/drm_of.h> 20 21 #include <linux/clk.h> 22 #include <linux/delay.h> 23 #include <linux/device.h> 24 #include <linux/io.h> 25 #include <linux/module.h> 26 #include <linux/platform_device.h> 27 #include <linux/pm_runtime.h> 28 #include <linux/phy/phy.h> 29 #include <linux/reset.h> 30 #include <linux/slab.h> 31 32 #include "zynqmp_disp.h" 33 #include "zynqmp_dp.h" 34 #include "zynqmp_dpsub.h" 35 #include "zynqmp_kms.h" 36 37 static uint zynqmp_dp_aux_timeout_ms = 50; 38 module_param_named(aux_timeout_ms, zynqmp_dp_aux_timeout_ms, uint, 0444); 39 MODULE_PARM_DESC(aux_timeout_ms, "DP aux timeout value in msec (default: 50)"); 40 41 /* 42 * Some sink requires a delay after power on request 43 */ 44 static uint zynqmp_dp_power_on_delay_ms = 4; 45 module_param_named(power_on_delay_ms, zynqmp_dp_power_on_delay_ms, uint, 0444); 46 MODULE_PARM_DESC(power_on_delay_ms, "DP power on delay in msec (default: 4)"); 47 48 /* Link configuration registers */ 49 #define ZYNQMP_DP_LINK_BW_SET 0x0 50 #define ZYNQMP_DP_LANE_COUNT_SET 0x4 51 #define ZYNQMP_DP_ENHANCED_FRAME_EN 0x8 52 #define ZYNQMP_DP_TRAINING_PATTERN_SET 0xc 53 #define ZYNQMP_DP_SCRAMBLING_DISABLE 0x14 54 #define ZYNQMP_DP_DOWNSPREAD_CTL 0x18 55 #define ZYNQMP_DP_SOFTWARE_RESET 0x1c 56 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM1 BIT(0) 57 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM2 BIT(1) 58 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM3 BIT(2) 59 #define ZYNQMP_DP_SOFTWARE_RESET_STREAM4 BIT(3) 60 #define ZYNQMP_DP_SOFTWARE_RESET_AUX BIT(7) 61 #define ZYNQMP_DP_SOFTWARE_RESET_ALL (ZYNQMP_DP_SOFTWARE_RESET_STREAM1 | \ 62 ZYNQMP_DP_SOFTWARE_RESET_STREAM2 | \ 63 ZYNQMP_DP_SOFTWARE_RESET_STREAM3 | \ 64 ZYNQMP_DP_SOFTWARE_RESET_STREAM4 | \ 65 ZYNQMP_DP_SOFTWARE_RESET_AUX) 66 67 /* Core enable registers */ 68 #define ZYNQMP_DP_TRANSMITTER_ENABLE 0x80 69 #define ZYNQMP_DP_MAIN_STREAM_ENABLE 0x84 70 #define ZYNQMP_DP_FORCE_SCRAMBLER_RESET 0xc0 71 #define ZYNQMP_DP_VERSION 0xf8 72 #define ZYNQMP_DP_VERSION_MAJOR_MASK GENMASK(31, 24) 73 #define ZYNQMP_DP_VERSION_MAJOR_SHIFT 24 74 #define ZYNQMP_DP_VERSION_MINOR_MASK GENMASK(23, 16) 75 #define ZYNQMP_DP_VERSION_MINOR_SHIFT 16 76 #define ZYNQMP_DP_VERSION_REVISION_MASK GENMASK(15, 12) 77 #define ZYNQMP_DP_VERSION_REVISION_SHIFT 12 78 #define ZYNQMP_DP_VERSION_PATCH_MASK GENMASK(11, 8) 79 #define ZYNQMP_DP_VERSION_PATCH_SHIFT 8 80 #define ZYNQMP_DP_VERSION_INTERNAL_MASK GENMASK(7, 0) 81 #define ZYNQMP_DP_VERSION_INTERNAL_SHIFT 0 82 83 /* Core ID registers */ 84 #define ZYNQMP_DP_CORE_ID 0xfc 85 #define ZYNQMP_DP_CORE_ID_MAJOR_MASK GENMASK(31, 24) 86 #define ZYNQMP_DP_CORE_ID_MAJOR_SHIFT 24 87 #define ZYNQMP_DP_CORE_ID_MINOR_MASK GENMASK(23, 16) 88 #define ZYNQMP_DP_CORE_ID_MINOR_SHIFT 16 89 #define ZYNQMP_DP_CORE_ID_REVISION_MASK GENMASK(15, 8) 90 #define ZYNQMP_DP_CORE_ID_REVISION_SHIFT 8 91 #define ZYNQMP_DP_CORE_ID_DIRECTION GENMASK(1) 92 93 /* AUX channel interface registers */ 94 #define ZYNQMP_DP_AUX_COMMAND 0x100 95 #define ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT 8 96 #define ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY BIT(12) 97 #define ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT 0 98 #define ZYNQMP_DP_AUX_WRITE_FIFO 0x104 99 #define ZYNQMP_DP_AUX_ADDRESS 0x108 100 #define ZYNQMP_DP_AUX_CLK_DIVIDER 0x10c 101 #define ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT 8 102 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE 0x130 103 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD BIT(0) 104 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST BIT(1) 105 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY BIT(2) 106 #define ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT BIT(3) 107 #define ZYNQMP_DP_AUX_REPLY_DATA 0x134 108 #define ZYNQMP_DP_AUX_REPLY_CODE 0x138 109 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK (0) 110 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_NACK BIT(0) 111 #define ZYNQMP_DP_AUX_REPLY_CODE_AUX_DEFER BIT(1) 112 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK (0) 113 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_NACK BIT(2) 114 #define ZYNQMP_DP_AUX_REPLY_CODE_I2C_DEFER BIT(3) 115 #define ZYNQMP_DP_AUX_REPLY_COUNT 0x13c 116 #define ZYNQMP_DP_REPLY_DATA_COUNT 0x148 117 #define ZYNQMP_DP_REPLY_DATA_COUNT_MASK 0xff 118 #define ZYNQMP_DP_INT_STATUS 0x3a0 119 #define ZYNQMP_DP_INT_MASK 0x3a4 120 #define ZYNQMP_DP_INT_EN 0x3a8 121 #define ZYNQMP_DP_INT_DS 0x3ac 122 #define ZYNQMP_DP_INT_HPD_IRQ BIT(0) 123 #define ZYNQMP_DP_INT_HPD_EVENT BIT(1) 124 #define ZYNQMP_DP_INT_REPLY_RECEIVED BIT(2) 125 #define ZYNQMP_DP_INT_REPLY_TIMEOUT BIT(3) 126 #define ZYNQMP_DP_INT_HPD_PULSE_DET BIT(4) 127 #define ZYNQMP_DP_INT_EXT_PKT_TXD BIT(5) 128 #define ZYNQMP_DP_INT_LIV_ABUF_UNDRFLW BIT(12) 129 #define ZYNQMP_DP_INT_VBLANK_START BIT(13) 130 #define ZYNQMP_DP_INT_PIXEL1_MATCH BIT(14) 131 #define ZYNQMP_DP_INT_PIXEL0_MATCH BIT(15) 132 #define ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK 0x3f0000 133 #define ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK 0xfc00000 134 #define ZYNQMP_DP_INT_CUST_TS_2 BIT(28) 135 #define ZYNQMP_DP_INT_CUST_TS BIT(29) 136 #define ZYNQMP_DP_INT_EXT_VSYNC_TS BIT(30) 137 #define ZYNQMP_DP_INT_VSYNC_TS BIT(31) 138 #define ZYNQMP_DP_INT_ALL (ZYNQMP_DP_INT_HPD_IRQ | \ 139 ZYNQMP_DP_INT_HPD_EVENT | \ 140 ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK | \ 141 ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK) 142 143 /* Main stream attribute registers */ 144 #define ZYNQMP_DP_MAIN_STREAM_HTOTAL 0x180 145 #define ZYNQMP_DP_MAIN_STREAM_VTOTAL 0x184 146 #define ZYNQMP_DP_MAIN_STREAM_POLARITY 0x188 147 #define ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT 0 148 #define ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT 1 149 #define ZYNQMP_DP_MAIN_STREAM_HSWIDTH 0x18c 150 #define ZYNQMP_DP_MAIN_STREAM_VSWIDTH 0x190 151 #define ZYNQMP_DP_MAIN_STREAM_HRES 0x194 152 #define ZYNQMP_DP_MAIN_STREAM_VRES 0x198 153 #define ZYNQMP_DP_MAIN_STREAM_HSTART 0x19c 154 #define ZYNQMP_DP_MAIN_STREAM_VSTART 0x1a0 155 #define ZYNQMP_DP_MAIN_STREAM_MISC0 0x1a4 156 #define ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK BIT(0) 157 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB (0 << 1) 158 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422 (5 << 1) 159 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444 (6 << 1) 160 #define ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK (7 << 1) 161 #define ZYNQMP_DP_MAIN_STREAM_MISC0_DYNAMIC_RANGE BIT(3) 162 #define ZYNQMP_DP_MAIN_STREAM_MISC0_YCBCR_COLR BIT(4) 163 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6 (0 << 5) 164 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8 (1 << 5) 165 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10 (2 << 5) 166 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12 (3 << 5) 167 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16 (4 << 5) 168 #define ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK (7 << 5) 169 #define ZYNQMP_DP_MAIN_STREAM_MISC1 0x1a8 170 #define ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN BIT(7) 171 #define ZYNQMP_DP_MAIN_STREAM_M_VID 0x1ac 172 #define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE 0x1b0 173 #define ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF 64 174 #define ZYNQMP_DP_MAIN_STREAM_N_VID 0x1b4 175 #define ZYNQMP_DP_USER_PIX_WIDTH 0x1b8 176 #define ZYNQMP_DP_USER_DATA_COUNT_PER_LANE 0x1bc 177 #define ZYNQMP_DP_MIN_BYTES_PER_TU 0x1c4 178 #define ZYNQMP_DP_FRAC_BYTES_PER_TU 0x1c8 179 #define ZYNQMP_DP_INIT_WAIT 0x1cc 180 181 /* PHY configuration and status registers */ 182 #define ZYNQMP_DP_PHY_RESET 0x200 183 #define ZYNQMP_DP_PHY_RESET_PHY_RESET BIT(0) 184 #define ZYNQMP_DP_PHY_RESET_GTTX_RESET BIT(1) 185 #define ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET BIT(8) 186 #define ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET BIT(9) 187 #define ZYNQMP_DP_PHY_RESET_ALL_RESET (ZYNQMP_DP_PHY_RESET_PHY_RESET | \ 188 ZYNQMP_DP_PHY_RESET_GTTX_RESET | \ 189 ZYNQMP_DP_PHY_RESET_PHY_PMA_RESET | \ 190 ZYNQMP_DP_PHY_RESET_PHY_PCS_RESET) 191 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_0 0x210 192 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_1 0x214 193 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_2 0x218 194 #define ZYNQMP_DP_PHY_PREEMPHASIS_LANE_3 0x21c 195 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_0 0x220 196 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_1 0x224 197 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_2 0x228 198 #define ZYNQMP_DP_PHY_VOLTAGE_DIFF_LANE_3 0x22c 199 #define ZYNQMP_DP_PHY_CLOCK_SELECT 0x234 200 #define ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G 0x1 201 #define ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G 0x3 202 #define ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G 0x5 203 #define ZYNQMP_DP_TX_PHY_POWER_DOWN 0x238 204 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_0 BIT(0) 205 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_1 BIT(1) 206 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_2 BIT(2) 207 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_LANE_3 BIT(3) 208 #define ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL 0xf 209 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_0 0x23c 210 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_1 0x240 211 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_2 0x244 212 #define ZYNQMP_DP_PHY_PRECURSOR_LANE_3 0x248 213 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_0 0x24c 214 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_1 0x250 215 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_2 0x254 216 #define ZYNQMP_DP_PHY_POSTCURSOR_LANE_3 0x258 217 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 0x24c 218 #define ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_1 0x250 219 #define ZYNQMP_DP_PHY_STATUS 0x280 220 #define ZYNQMP_DP_PHY_STATUS_PLL_LOCKED_SHIFT 4 221 #define ZYNQMP_DP_PHY_STATUS_FPGA_PLL_LOCKED BIT(6) 222 223 /* Audio registers */ 224 #define ZYNQMP_DP_TX_AUDIO_CONTROL 0x300 225 #define ZYNQMP_DP_TX_AUDIO_CHANNELS 0x304 226 #define ZYNQMP_DP_TX_AUDIO_INFO_DATA 0x308 227 #define ZYNQMP_DP_TX_M_AUD 0x328 228 #define ZYNQMP_DP_TX_N_AUD 0x32c 229 #define ZYNQMP_DP_TX_AUDIO_EXT_DATA 0x330 230 231 #define ZYNQMP_DP_MAX_LANES 2 232 #define ZYNQMP_MAX_FREQ 3000000 233 234 #define DP_REDUCED_BIT_RATE 162000 235 #define DP_HIGH_BIT_RATE 270000 236 #define DP_HIGH_BIT_RATE2 540000 237 #define DP_MAX_TRAINING_TRIES 5 238 #define DP_V1_2 0x12 239 240 /** 241 * struct zynqmp_dp_link_config - Common link config between source and sink 242 * @max_rate: maximum link rate 243 * @max_lanes: maximum number of lanes 244 */ 245 struct zynqmp_dp_link_config { 246 int max_rate; 247 u8 max_lanes; 248 }; 249 250 /** 251 * struct zynqmp_dp_mode - Configured mode of DisplayPort 252 * @bw_code: code for bandwidth(link rate) 253 * @lane_cnt: number of lanes 254 * @pclock: pixel clock frequency of current mode 255 * @fmt: format identifier string 256 */ 257 struct zynqmp_dp_mode { 258 u8 bw_code; 259 u8 lane_cnt; 260 int pclock; 261 const char *fmt; 262 }; 263 264 /** 265 * struct zynqmp_dp_config - Configuration of DisplayPort from DTS 266 * @misc0: misc0 configuration (per DP v1.2 spec) 267 * @misc1: misc1 configuration (per DP v1.2 spec) 268 * @bpp: bits per pixel 269 */ 270 struct zynqmp_dp_config { 271 u8 misc0; 272 u8 misc1; 273 u8 bpp; 274 }; 275 276 /** 277 * struct zynqmp_dp - Xilinx DisplayPort core 278 * @dev: device structure 279 * @dpsub: Display subsystem 280 * @iomem: device I/O memory for register access 281 * @reset: reset controller 282 * @irq: irq 283 * @bridge: DRM bridge for the DP encoder 284 * @next_bridge: The downstream bridge 285 * @config: IP core configuration from DTS 286 * @aux: aux channel 287 * @phy: PHY handles for DP lanes 288 * @num_lanes: number of enabled phy lanes 289 * @hpd_work: hot plug detection worker 290 * @status: connection status 291 * @enabled: flag to indicate if the device is enabled 292 * @dpcd: DP configuration data from currently connected sink device 293 * @link_config: common link configuration between IP core and sink device 294 * @mode: current mode between IP core and sink device 295 * @train_set: set of training data 296 */ 297 struct zynqmp_dp { 298 struct device *dev; 299 struct zynqmp_dpsub *dpsub; 300 void __iomem *iomem; 301 struct reset_control *reset; 302 int irq; 303 304 struct drm_bridge bridge; 305 struct drm_bridge *next_bridge; 306 307 struct zynqmp_dp_config config; 308 struct drm_dp_aux aux; 309 struct phy *phy[ZYNQMP_DP_MAX_LANES]; 310 u8 num_lanes; 311 struct delayed_work hpd_work; 312 enum drm_connector_status status; 313 bool enabled; 314 315 u8 dpcd[DP_RECEIVER_CAP_SIZE]; 316 struct zynqmp_dp_link_config link_config; 317 struct zynqmp_dp_mode mode; 318 u8 train_set[ZYNQMP_DP_MAX_LANES]; 319 }; 320 321 static inline struct zynqmp_dp *bridge_to_dp(struct drm_bridge *bridge) 322 { 323 return container_of(bridge, struct zynqmp_dp, bridge); 324 } 325 326 static void zynqmp_dp_write(struct zynqmp_dp *dp, int offset, u32 val) 327 { 328 writel(val, dp->iomem + offset); 329 } 330 331 static u32 zynqmp_dp_read(struct zynqmp_dp *dp, int offset) 332 { 333 return readl(dp->iomem + offset); 334 } 335 336 static void zynqmp_dp_clr(struct zynqmp_dp *dp, int offset, u32 clr) 337 { 338 zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) & ~clr); 339 } 340 341 static void zynqmp_dp_set(struct zynqmp_dp *dp, int offset, u32 set) 342 { 343 zynqmp_dp_write(dp, offset, zynqmp_dp_read(dp, offset) | set); 344 } 345 346 /* ----------------------------------------------------------------------------- 347 * PHY Handling 348 */ 349 350 #define RST_TIMEOUT_MS 1000 351 352 static int zynqmp_dp_reset(struct zynqmp_dp *dp, bool assert) 353 { 354 unsigned long timeout; 355 356 if (assert) 357 reset_control_assert(dp->reset); 358 else 359 reset_control_deassert(dp->reset); 360 361 /* Wait for the (de)assert to complete. */ 362 timeout = jiffies + msecs_to_jiffies(RST_TIMEOUT_MS); 363 while (!time_after_eq(jiffies, timeout)) { 364 bool status = !!reset_control_status(dp->reset); 365 366 if (assert == status) 367 return 0; 368 369 cpu_relax(); 370 } 371 372 dev_err(dp->dev, "reset %s timeout\n", assert ? "assert" : "deassert"); 373 return -ETIMEDOUT; 374 } 375 376 /** 377 * zynqmp_dp_phy_init - Initialize the phy 378 * @dp: DisplayPort IP core structure 379 * 380 * Initialize the phy. 381 * 382 * Return: 0 if the phy instances are initialized correctly, or the error code 383 * returned from the callee functions. 384 */ 385 static int zynqmp_dp_phy_init(struct zynqmp_dp *dp) 386 { 387 int ret; 388 int i; 389 390 for (i = 0; i < dp->num_lanes; i++) { 391 ret = phy_init(dp->phy[i]); 392 if (ret) { 393 dev_err(dp->dev, "failed to init phy lane %d\n", i); 394 return ret; 395 } 396 } 397 398 zynqmp_dp_clr(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET); 399 400 /* 401 * Power on lanes in reverse order as only lane 0 waits for the PLL to 402 * lock. 403 */ 404 for (i = dp->num_lanes - 1; i >= 0; i--) { 405 ret = phy_power_on(dp->phy[i]); 406 if (ret) { 407 dev_err(dp->dev, "failed to power on phy lane %d\n", i); 408 return ret; 409 } 410 } 411 412 return 0; 413 } 414 415 /** 416 * zynqmp_dp_phy_exit - Exit the phy 417 * @dp: DisplayPort IP core structure 418 * 419 * Exit the phy. 420 */ 421 static void zynqmp_dp_phy_exit(struct zynqmp_dp *dp) 422 { 423 unsigned int i; 424 int ret; 425 426 for (i = 0; i < dp->num_lanes; i++) { 427 ret = phy_power_off(dp->phy[i]); 428 if (ret) 429 dev_err(dp->dev, "failed to power off phy(%d) %d\n", i, 430 ret); 431 } 432 433 for (i = 0; i < dp->num_lanes; i++) { 434 ret = phy_exit(dp->phy[i]); 435 if (ret) 436 dev_err(dp->dev, "failed to exit phy(%d) %d\n", i, ret); 437 } 438 } 439 440 /** 441 * zynqmp_dp_phy_probe - Probe the PHYs 442 * @dp: DisplayPort IP core structure 443 * 444 * Probe PHYs for all lanes. Less PHYs may be available than the number of 445 * lanes, which is not considered an error as long as at least one PHY is 446 * found. The caller can check dp->num_lanes to check how many PHYs were found. 447 * 448 * Return: 449 * * 0 - Success 450 * * -ENXIO - No PHY found 451 * * -EPROBE_DEFER - Probe deferral requested 452 * * Other negative value - PHY retrieval failure 453 */ 454 static int zynqmp_dp_phy_probe(struct zynqmp_dp *dp) 455 { 456 unsigned int i; 457 458 for (i = 0; i < ZYNQMP_DP_MAX_LANES; i++) { 459 char phy_name[16]; 460 struct phy *phy; 461 462 snprintf(phy_name, sizeof(phy_name), "dp-phy%d", i); 463 phy = devm_phy_get(dp->dev, phy_name); 464 465 if (IS_ERR(phy)) { 466 switch (PTR_ERR(phy)) { 467 case -ENODEV: 468 if (dp->num_lanes) 469 return 0; 470 471 dev_err(dp->dev, "no PHY found\n"); 472 return -ENXIO; 473 474 case -EPROBE_DEFER: 475 return -EPROBE_DEFER; 476 477 default: 478 dev_err(dp->dev, "failed to get PHY lane %u\n", 479 i); 480 return PTR_ERR(phy); 481 } 482 } 483 484 dp->phy[i] = phy; 485 dp->num_lanes++; 486 } 487 488 return 0; 489 } 490 491 /** 492 * zynqmp_dp_phy_ready - Check if PHY is ready 493 * @dp: DisplayPort IP core structure 494 * 495 * Check if PHY is ready. If PHY is not ready, wait 1ms to check for 100 times. 496 * This amount of delay was suggested by IP designer. 497 * 498 * Return: 0 if PHY is ready, or -ENODEV if PHY is not ready. 499 */ 500 static int zynqmp_dp_phy_ready(struct zynqmp_dp *dp) 501 { 502 u32 i, reg, ready; 503 504 ready = (1 << dp->num_lanes) - 1; 505 506 /* Wait for 100 * 1ms. This should be enough time for PHY to be ready */ 507 for (i = 0; ; i++) { 508 reg = zynqmp_dp_read(dp, ZYNQMP_DP_PHY_STATUS); 509 if ((reg & ready) == ready) 510 return 0; 511 512 if (i == 100) { 513 dev_err(dp->dev, "PHY isn't ready\n"); 514 return -ENODEV; 515 } 516 517 usleep_range(1000, 1100); 518 } 519 520 return 0; 521 } 522 523 /* ----------------------------------------------------------------------------- 524 * DisplayPort Link Training 525 */ 526 527 /** 528 * zynqmp_dp_max_rate - Calculate and return available max pixel clock 529 * @link_rate: link rate (Kilo-bytes / sec) 530 * @lane_num: number of lanes 531 * @bpp: bits per pixel 532 * 533 * Return: max pixel clock (KHz) supported by current link config. 534 */ 535 static inline int zynqmp_dp_max_rate(int link_rate, u8 lane_num, u8 bpp) 536 { 537 return link_rate * lane_num * 8 / bpp; 538 } 539 540 /** 541 * zynqmp_dp_mode_configure - Configure the link values 542 * @dp: DisplayPort IP core structure 543 * @pclock: pixel clock for requested display mode 544 * @current_bw: current link rate 545 * 546 * Find the link configuration values, rate and lane count for requested pixel 547 * clock @pclock. The @pclock is stored in the mode to be used in other 548 * functions later. The returned rate is downshifted from the current rate 549 * @current_bw. 550 * 551 * Return: Current link rate code, or -EINVAL. 552 */ 553 static int zynqmp_dp_mode_configure(struct zynqmp_dp *dp, int pclock, 554 u8 current_bw) 555 { 556 int max_rate = dp->link_config.max_rate; 557 u8 bw_code; 558 u8 max_lanes = dp->link_config.max_lanes; 559 u8 max_link_rate_code = drm_dp_link_rate_to_bw_code(max_rate); 560 u8 bpp = dp->config.bpp; 561 u8 lane_cnt; 562 563 /* Downshift from current bandwidth */ 564 switch (current_bw) { 565 case DP_LINK_BW_5_4: 566 bw_code = DP_LINK_BW_2_7; 567 break; 568 case DP_LINK_BW_2_7: 569 bw_code = DP_LINK_BW_1_62; 570 break; 571 case DP_LINK_BW_1_62: 572 dev_err(dp->dev, "can't downshift. already lowest link rate\n"); 573 return -EINVAL; 574 default: 575 /* If not given, start with max supported */ 576 bw_code = max_link_rate_code; 577 break; 578 } 579 580 for (lane_cnt = 1; lane_cnt <= max_lanes; lane_cnt <<= 1) { 581 int bw; 582 u32 rate; 583 584 bw = drm_dp_bw_code_to_link_rate(bw_code); 585 rate = zynqmp_dp_max_rate(bw, lane_cnt, bpp); 586 if (pclock <= rate) { 587 dp->mode.bw_code = bw_code; 588 dp->mode.lane_cnt = lane_cnt; 589 dp->mode.pclock = pclock; 590 return dp->mode.bw_code; 591 } 592 } 593 594 dev_err(dp->dev, "failed to configure link values\n"); 595 596 return -EINVAL; 597 } 598 599 /** 600 * zynqmp_dp_adjust_train - Adjust train values 601 * @dp: DisplayPort IP core structure 602 * @link_status: link status from sink which contains requested training values 603 */ 604 static void zynqmp_dp_adjust_train(struct zynqmp_dp *dp, 605 u8 link_status[DP_LINK_STATUS_SIZE]) 606 { 607 u8 *train_set = dp->train_set; 608 u8 voltage = 0, preemphasis = 0; 609 u8 i; 610 611 for (i = 0; i < dp->mode.lane_cnt; i++) { 612 u8 v = drm_dp_get_adjust_request_voltage(link_status, i); 613 u8 p = drm_dp_get_adjust_request_pre_emphasis(link_status, i); 614 615 if (v > voltage) 616 voltage = v; 617 618 if (p > preemphasis) 619 preemphasis = p; 620 } 621 622 if (voltage >= DP_TRAIN_VOLTAGE_SWING_LEVEL_3) 623 voltage |= DP_TRAIN_MAX_SWING_REACHED; 624 625 if (preemphasis >= DP_TRAIN_PRE_EMPH_LEVEL_2) 626 preemphasis |= DP_TRAIN_MAX_PRE_EMPHASIS_REACHED; 627 628 for (i = 0; i < dp->mode.lane_cnt; i++) 629 train_set[i] = voltage | preemphasis; 630 } 631 632 /** 633 * zynqmp_dp_update_vs_emph - Update the training values 634 * @dp: DisplayPort IP core structure 635 * 636 * Update the training values based on the request from sink. The mapped values 637 * are predefined, and values(vs, pe, pc) are from the device manual. 638 * 639 * Return: 0 if vs and emph are updated successfully, or the error code returned 640 * by drm_dp_dpcd_write(). 641 */ 642 static int zynqmp_dp_update_vs_emph(struct zynqmp_dp *dp) 643 { 644 unsigned int i; 645 int ret; 646 647 ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, dp->train_set, 648 dp->mode.lane_cnt); 649 if (ret < 0) 650 return ret; 651 652 for (i = 0; i < dp->mode.lane_cnt; i++) { 653 u32 reg = ZYNQMP_DP_SUB_TX_PHY_PRECURSOR_LANE_0 + i * 4; 654 union phy_configure_opts opts = { 0 }; 655 u8 train = dp->train_set[i]; 656 657 opts.dp.voltage[0] = (train & DP_TRAIN_VOLTAGE_SWING_MASK) 658 >> DP_TRAIN_VOLTAGE_SWING_SHIFT; 659 opts.dp.pre[0] = (train & DP_TRAIN_PRE_EMPHASIS_MASK) 660 >> DP_TRAIN_PRE_EMPHASIS_SHIFT; 661 662 phy_configure(dp->phy[i], &opts); 663 664 zynqmp_dp_write(dp, reg, 0x2); 665 } 666 667 return 0; 668 } 669 670 /** 671 * zynqmp_dp_link_train_cr - Train clock recovery 672 * @dp: DisplayPort IP core structure 673 * 674 * Return: 0 if clock recovery train is done successfully, or corresponding 675 * error code. 676 */ 677 static int zynqmp_dp_link_train_cr(struct zynqmp_dp *dp) 678 { 679 u8 link_status[DP_LINK_STATUS_SIZE]; 680 u8 lane_cnt = dp->mode.lane_cnt; 681 u8 vs = 0, tries = 0; 682 u16 max_tries, i; 683 bool cr_done; 684 int ret; 685 686 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, 687 DP_TRAINING_PATTERN_1); 688 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 689 DP_TRAINING_PATTERN_1 | 690 DP_LINK_SCRAMBLING_DISABLE); 691 if (ret < 0) 692 return ret; 693 694 /* 695 * 256 loops should be maximum iterations for 4 lanes and 4 values. 696 * So, This loop should exit before 512 iterations 697 */ 698 for (max_tries = 0; max_tries < 512; max_tries++) { 699 ret = zynqmp_dp_update_vs_emph(dp); 700 if (ret) 701 return ret; 702 703 drm_dp_link_train_clock_recovery_delay(&dp->aux, dp->dpcd); 704 ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status); 705 if (ret < 0) 706 return ret; 707 708 cr_done = drm_dp_clock_recovery_ok(link_status, lane_cnt); 709 if (cr_done) 710 break; 711 712 for (i = 0; i < lane_cnt; i++) 713 if (!(dp->train_set[i] & DP_TRAIN_MAX_SWING_REACHED)) 714 break; 715 if (i == lane_cnt) 716 break; 717 718 if ((dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) == vs) 719 tries++; 720 else 721 tries = 0; 722 723 if (tries == DP_MAX_TRAINING_TRIES) 724 break; 725 726 vs = dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK; 727 zynqmp_dp_adjust_train(dp, link_status); 728 } 729 730 if (!cr_done) 731 return -EIO; 732 733 return 0; 734 } 735 736 /** 737 * zynqmp_dp_link_train_ce - Train channel equalization 738 * @dp: DisplayPort IP core structure 739 * 740 * Return: 0 if channel equalization train is done successfully, or 741 * corresponding error code. 742 */ 743 static int zynqmp_dp_link_train_ce(struct zynqmp_dp *dp) 744 { 745 u8 link_status[DP_LINK_STATUS_SIZE]; 746 u8 lane_cnt = dp->mode.lane_cnt; 747 u32 pat, tries; 748 int ret; 749 bool ce_done; 750 751 if (dp->dpcd[DP_DPCD_REV] >= DP_V1_2 && 752 dp->dpcd[DP_MAX_LANE_COUNT] & DP_TPS3_SUPPORTED) 753 pat = DP_TRAINING_PATTERN_3; 754 else 755 pat = DP_TRAINING_PATTERN_2; 756 757 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, pat); 758 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 759 pat | DP_LINK_SCRAMBLING_DISABLE); 760 if (ret < 0) 761 return ret; 762 763 for (tries = 0; tries < DP_MAX_TRAINING_TRIES; tries++) { 764 ret = zynqmp_dp_update_vs_emph(dp); 765 if (ret) 766 return ret; 767 768 drm_dp_link_train_channel_eq_delay(&dp->aux, dp->dpcd); 769 ret = drm_dp_dpcd_read_link_status(&dp->aux, link_status); 770 if (ret < 0) 771 return ret; 772 773 ce_done = drm_dp_channel_eq_ok(link_status, lane_cnt); 774 if (ce_done) 775 break; 776 777 zynqmp_dp_adjust_train(dp, link_status); 778 } 779 780 if (!ce_done) 781 return -EIO; 782 783 return 0; 784 } 785 786 /** 787 * zynqmp_dp_train - Train the link 788 * @dp: DisplayPort IP core structure 789 * 790 * Return: 0 if all trains are done successfully, or corresponding error code. 791 */ 792 static int zynqmp_dp_train(struct zynqmp_dp *dp) 793 { 794 u32 reg; 795 u8 bw_code = dp->mode.bw_code; 796 u8 lane_cnt = dp->mode.lane_cnt; 797 u8 aux_lane_cnt = lane_cnt; 798 bool enhanced; 799 int ret; 800 801 zynqmp_dp_write(dp, ZYNQMP_DP_LANE_COUNT_SET, lane_cnt); 802 enhanced = drm_dp_enhanced_frame_cap(dp->dpcd); 803 if (enhanced) { 804 zynqmp_dp_write(dp, ZYNQMP_DP_ENHANCED_FRAME_EN, 1); 805 aux_lane_cnt |= DP_LANE_COUNT_ENHANCED_FRAME_EN; 806 } 807 808 if (dp->dpcd[3] & 0x1) { 809 zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 1); 810 drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 811 DP_SPREAD_AMP_0_5); 812 } else { 813 zynqmp_dp_write(dp, ZYNQMP_DP_DOWNSPREAD_CTL, 0); 814 drm_dp_dpcd_writeb(&dp->aux, DP_DOWNSPREAD_CTRL, 0); 815 } 816 817 ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, aux_lane_cnt); 818 if (ret < 0) { 819 dev_err(dp->dev, "failed to set lane count\n"); 820 return ret; 821 } 822 823 ret = drm_dp_dpcd_writeb(&dp->aux, DP_MAIN_LINK_CHANNEL_CODING_SET, 824 DP_SET_ANSI_8B10B); 825 if (ret < 0) { 826 dev_err(dp->dev, "failed to set ANSI 8B/10B encoding\n"); 827 return ret; 828 } 829 830 ret = drm_dp_dpcd_writeb(&dp->aux, DP_LINK_BW_SET, bw_code); 831 if (ret < 0) { 832 dev_err(dp->dev, "failed to set DP bandwidth\n"); 833 return ret; 834 } 835 836 zynqmp_dp_write(dp, ZYNQMP_DP_LINK_BW_SET, bw_code); 837 switch (bw_code) { 838 case DP_LINK_BW_1_62: 839 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_1_62G; 840 break; 841 case DP_LINK_BW_2_7: 842 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_2_70G; 843 break; 844 case DP_LINK_BW_5_4: 845 default: 846 reg = ZYNQMP_DP_PHY_CLOCK_SELECT_5_40G; 847 break; 848 } 849 850 zynqmp_dp_write(dp, ZYNQMP_DP_PHY_CLOCK_SELECT, reg); 851 ret = zynqmp_dp_phy_ready(dp); 852 if (ret < 0) 853 return ret; 854 855 zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 1); 856 memset(dp->train_set, 0, sizeof(dp->train_set)); 857 ret = zynqmp_dp_link_train_cr(dp); 858 if (ret) 859 return ret; 860 861 ret = zynqmp_dp_link_train_ce(dp); 862 if (ret) 863 return ret; 864 865 ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, 866 DP_TRAINING_PATTERN_DISABLE); 867 if (ret < 0) { 868 dev_err(dp->dev, "failed to disable training pattern\n"); 869 return ret; 870 } 871 zynqmp_dp_write(dp, ZYNQMP_DP_TRAINING_PATTERN_SET, 872 DP_TRAINING_PATTERN_DISABLE); 873 874 zynqmp_dp_write(dp, ZYNQMP_DP_SCRAMBLING_DISABLE, 0); 875 876 return 0; 877 } 878 879 /** 880 * zynqmp_dp_train_loop - Downshift the link rate during training 881 * @dp: DisplayPort IP core structure 882 * 883 * Train the link by downshifting the link rate if training is not successful. 884 */ 885 static void zynqmp_dp_train_loop(struct zynqmp_dp *dp) 886 { 887 struct zynqmp_dp_mode *mode = &dp->mode; 888 u8 bw = mode->bw_code; 889 int ret; 890 891 do { 892 if (dp->status == connector_status_disconnected || 893 !dp->enabled) 894 return; 895 896 ret = zynqmp_dp_train(dp); 897 if (!ret) 898 return; 899 900 ret = zynqmp_dp_mode_configure(dp, mode->pclock, bw); 901 if (ret < 0) 902 goto err_out; 903 904 bw = ret; 905 } while (bw >= DP_LINK_BW_1_62); 906 907 err_out: 908 dev_err(dp->dev, "failed to train the DP link\n"); 909 } 910 911 /* ----------------------------------------------------------------------------- 912 * DisplayPort AUX 913 */ 914 915 #define AUX_READ_BIT 0x1 916 917 /** 918 * zynqmp_dp_aux_cmd_submit - Submit aux command 919 * @dp: DisplayPort IP core structure 920 * @cmd: aux command 921 * @addr: aux address 922 * @buf: buffer for command data 923 * @bytes: number of bytes for @buf 924 * @reply: reply code to be returned 925 * 926 * Submit an aux command. All aux related commands, native or i2c aux 927 * read/write, are submitted through this function. The function is mapped to 928 * the transfer function of struct drm_dp_aux. This function involves in 929 * multiple register reads/writes, thus synchronization is needed, and it is 930 * done by drm_dp_helper using @hw_mutex. The calling thread goes into sleep 931 * if there's no immediate reply to the command submission. The reply code is 932 * returned at @reply if @reply != NULL. 933 * 934 * Return: 0 if the command is submitted properly, or corresponding error code: 935 * -EBUSY when there is any request already being processed 936 * -ETIMEDOUT when receiving reply is timed out 937 * -EIO when received bytes are less than requested 938 */ 939 static int zynqmp_dp_aux_cmd_submit(struct zynqmp_dp *dp, u32 cmd, u16 addr, 940 u8 *buf, u8 bytes, u8 *reply) 941 { 942 bool is_read = (cmd & AUX_READ_BIT) ? true : false; 943 u32 reg, i; 944 945 reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 946 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REQUEST) 947 return -EBUSY; 948 949 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_ADDRESS, addr); 950 if (!is_read) 951 for (i = 0; i < bytes; i++) 952 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_WRITE_FIFO, 953 buf[i]); 954 955 reg = cmd << ZYNQMP_DP_AUX_COMMAND_CMD_SHIFT; 956 if (!buf || !bytes) 957 reg |= ZYNQMP_DP_AUX_COMMAND_ADDRESS_ONLY; 958 else 959 reg |= (bytes - 1) << ZYNQMP_DP_AUX_COMMAND_BYTES_SHIFT; 960 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_COMMAND, reg); 961 962 /* Wait for reply to be delivered upto 2ms */ 963 for (i = 0; ; i++) { 964 reg = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 965 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY) 966 break; 967 968 if (reg & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_REPLY_TIMEOUT || 969 i == 2) 970 return -ETIMEDOUT; 971 972 usleep_range(1000, 1100); 973 } 974 975 reg = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_CODE); 976 if (reply) 977 *reply = reg; 978 979 if (is_read && 980 (reg == ZYNQMP_DP_AUX_REPLY_CODE_AUX_ACK || 981 reg == ZYNQMP_DP_AUX_REPLY_CODE_I2C_ACK)) { 982 reg = zynqmp_dp_read(dp, ZYNQMP_DP_REPLY_DATA_COUNT); 983 if ((reg & ZYNQMP_DP_REPLY_DATA_COUNT_MASK) != bytes) 984 return -EIO; 985 986 for (i = 0; i < bytes; i++) 987 buf[i] = zynqmp_dp_read(dp, ZYNQMP_DP_AUX_REPLY_DATA); 988 } 989 990 return 0; 991 } 992 993 static ssize_t 994 zynqmp_dp_aux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg) 995 { 996 struct zynqmp_dp *dp = container_of(aux, struct zynqmp_dp, aux); 997 int ret; 998 unsigned int i, iter; 999 1000 /* Number of loops = timeout in msec / aux delay (400 usec) */ 1001 iter = zynqmp_dp_aux_timeout_ms * 1000 / 400; 1002 iter = iter ? iter : 1; 1003 1004 for (i = 0; i < iter; i++) { 1005 ret = zynqmp_dp_aux_cmd_submit(dp, msg->request, msg->address, 1006 msg->buffer, msg->size, 1007 &msg->reply); 1008 if (!ret) { 1009 dev_dbg(dp->dev, "aux %d retries\n", i); 1010 return msg->size; 1011 } 1012 1013 if (dp->status == connector_status_disconnected) { 1014 dev_dbg(dp->dev, "no connected aux device\n"); 1015 return -ENODEV; 1016 } 1017 1018 usleep_range(400, 500); 1019 } 1020 1021 dev_dbg(dp->dev, "failed to do aux transfer (%d)\n", ret); 1022 1023 return ret; 1024 } 1025 1026 /** 1027 * zynqmp_dp_aux_init - Initialize and register the DP AUX 1028 * @dp: DisplayPort IP core structure 1029 * 1030 * Program the AUX clock divider and filter and register the DP AUX adapter. 1031 * 1032 * Return: 0 on success, error value otherwise 1033 */ 1034 static int zynqmp_dp_aux_init(struct zynqmp_dp *dp) 1035 { 1036 unsigned long rate; 1037 unsigned int w; 1038 1039 /* 1040 * The AUX_SIGNAL_WIDTH_FILTER is the number of APB clock cycles 1041 * corresponding to the AUX pulse. Allowable values are 8, 16, 24, 32, 1042 * 40 and 48. The AUX pulse width must be between 0.4µs and 0.6µs, 1043 * compute the w / 8 value corresponding to 0.4µs rounded up, and make 1044 * sure it stays below 0.6µs and within the allowable values. 1045 */ 1046 rate = clk_get_rate(dp->dpsub->apb_clk); 1047 w = DIV_ROUND_UP(4 * rate, 1000 * 1000 * 10 * 8) * 8; 1048 if (w > 6 * rate / (1000 * 1000 * 10) || w > 48) { 1049 dev_err(dp->dev, "aclk frequency too high\n"); 1050 return -EINVAL; 1051 } 1052 1053 zynqmp_dp_write(dp, ZYNQMP_DP_AUX_CLK_DIVIDER, 1054 (w << ZYNQMP_DP_AUX_CLK_DIVIDER_AUX_FILTER_SHIFT) | 1055 (rate / (1000 * 1000))); 1056 1057 dp->aux.name = "ZynqMP DP AUX"; 1058 dp->aux.dev = dp->dev; 1059 dp->aux.drm_dev = dp->bridge.dev; 1060 dp->aux.transfer = zynqmp_dp_aux_transfer; 1061 1062 return drm_dp_aux_register(&dp->aux); 1063 } 1064 1065 /** 1066 * zynqmp_dp_aux_cleanup - Cleanup the DP AUX 1067 * @dp: DisplayPort IP core structure 1068 * 1069 * Unregister the DP AUX adapter. 1070 */ 1071 static void zynqmp_dp_aux_cleanup(struct zynqmp_dp *dp) 1072 { 1073 drm_dp_aux_unregister(&dp->aux); 1074 } 1075 1076 /* ----------------------------------------------------------------------------- 1077 * DisplayPort Generic Support 1078 */ 1079 1080 /** 1081 * zynqmp_dp_update_misc - Write the misc registers 1082 * @dp: DisplayPort IP core structure 1083 * 1084 * The misc register values are stored in the structure, and this 1085 * function applies the values into the registers. 1086 */ 1087 static void zynqmp_dp_update_misc(struct zynqmp_dp *dp) 1088 { 1089 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC0, dp->config.misc0); 1090 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_MISC1, dp->config.misc1); 1091 } 1092 1093 /** 1094 * zynqmp_dp_set_format - Set the input format 1095 * @dp: DisplayPort IP core structure 1096 * @info: Display info 1097 * @format: input format 1098 * @bpc: bits per component 1099 * 1100 * Update misc register values based on input @format and @bpc. 1101 * 1102 * Return: 0 on success, or -EINVAL. 1103 */ 1104 static int zynqmp_dp_set_format(struct zynqmp_dp *dp, 1105 const struct drm_display_info *info, 1106 enum zynqmp_dpsub_format format, 1107 unsigned int bpc) 1108 { 1109 struct zynqmp_dp_config *config = &dp->config; 1110 unsigned int num_colors; 1111 1112 config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_MASK; 1113 config->misc1 &= ~ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN; 1114 1115 switch (format) { 1116 case ZYNQMP_DPSUB_FORMAT_RGB: 1117 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_RGB; 1118 num_colors = 3; 1119 break; 1120 1121 case ZYNQMP_DPSUB_FORMAT_YCRCB444: 1122 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_444; 1123 num_colors = 3; 1124 break; 1125 1126 case ZYNQMP_DPSUB_FORMAT_YCRCB422: 1127 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_COMP_FORMAT_YCRCB_422; 1128 num_colors = 2; 1129 break; 1130 1131 case ZYNQMP_DPSUB_FORMAT_YONLY: 1132 config->misc1 |= ZYNQMP_DP_MAIN_STREAM_MISC1_Y_ONLY_EN; 1133 num_colors = 1; 1134 break; 1135 1136 default: 1137 dev_err(dp->dev, "Invalid colormetry in DT\n"); 1138 return -EINVAL; 1139 } 1140 1141 if (info && info->bpc && bpc > info->bpc) { 1142 dev_warn(dp->dev, 1143 "downgrading requested %ubpc to display limit %ubpc\n", 1144 bpc, info->bpc); 1145 bpc = info->bpc; 1146 } 1147 1148 config->misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_MASK; 1149 1150 switch (bpc) { 1151 case 6: 1152 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_6; 1153 break; 1154 case 8: 1155 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8; 1156 break; 1157 case 10: 1158 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_10; 1159 break; 1160 case 12: 1161 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_12; 1162 break; 1163 case 16: 1164 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_16; 1165 break; 1166 default: 1167 dev_warn(dp->dev, "Not supported bpc (%u). fall back to 8bpc\n", 1168 bpc); 1169 config->misc0 |= ZYNQMP_DP_MAIN_STREAM_MISC0_BPC_8; 1170 bpc = 8; 1171 break; 1172 } 1173 1174 /* Update the current bpp based on the format. */ 1175 config->bpp = bpc * num_colors; 1176 1177 return 0; 1178 } 1179 1180 /** 1181 * zynqmp_dp_encoder_mode_set_transfer_unit - Set the transfer unit values 1182 * @dp: DisplayPort IP core structure 1183 * @mode: requested display mode 1184 * 1185 * Set the transfer unit, and calculate all transfer unit size related values. 1186 * Calculation is based on DP and IP core specification. 1187 */ 1188 static void 1189 zynqmp_dp_encoder_mode_set_transfer_unit(struct zynqmp_dp *dp, 1190 const struct drm_display_mode *mode) 1191 { 1192 u32 tu = ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE_TU_SIZE_DEF; 1193 u32 bw, vid_kbytes, avg_bytes_per_tu, init_wait; 1194 1195 /* Use the max transfer unit size (default) */ 1196 zynqmp_dp_write(dp, ZYNQMP_DP_MSA_TRANSFER_UNIT_SIZE, tu); 1197 1198 vid_kbytes = mode->clock * (dp->config.bpp / 8); 1199 bw = drm_dp_bw_code_to_link_rate(dp->mode.bw_code); 1200 avg_bytes_per_tu = vid_kbytes * tu / (dp->mode.lane_cnt * bw / 1000); 1201 zynqmp_dp_write(dp, ZYNQMP_DP_MIN_BYTES_PER_TU, 1202 avg_bytes_per_tu / 1000); 1203 zynqmp_dp_write(dp, ZYNQMP_DP_FRAC_BYTES_PER_TU, 1204 avg_bytes_per_tu % 1000); 1205 1206 /* Configure the initial wait cycle based on transfer unit size */ 1207 if (tu < (avg_bytes_per_tu / 1000)) 1208 init_wait = 0; 1209 else if ((avg_bytes_per_tu / 1000) <= 4) 1210 init_wait = tu; 1211 else 1212 init_wait = tu - avg_bytes_per_tu / 1000; 1213 1214 zynqmp_dp_write(dp, ZYNQMP_DP_INIT_WAIT, init_wait); 1215 } 1216 1217 /** 1218 * zynqmp_dp_encoder_mode_set_stream - Configure the main stream 1219 * @dp: DisplayPort IP core structure 1220 * @mode: requested display mode 1221 * 1222 * Configure the main stream based on the requested mode @mode. Calculation is 1223 * based on IP core specification. 1224 */ 1225 static void zynqmp_dp_encoder_mode_set_stream(struct zynqmp_dp *dp, 1226 const struct drm_display_mode *mode) 1227 { 1228 u8 lane_cnt = dp->mode.lane_cnt; 1229 u32 reg, wpl; 1230 unsigned int rate; 1231 1232 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HTOTAL, mode->htotal); 1233 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VTOTAL, mode->vtotal); 1234 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_POLARITY, 1235 (!!(mode->flags & DRM_MODE_FLAG_PVSYNC) << 1236 ZYNQMP_DP_MAIN_STREAM_POLARITY_VSYNC_SHIFT) | 1237 (!!(mode->flags & DRM_MODE_FLAG_PHSYNC) << 1238 ZYNQMP_DP_MAIN_STREAM_POLARITY_HSYNC_SHIFT)); 1239 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSWIDTH, 1240 mode->hsync_end - mode->hsync_start); 1241 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSWIDTH, 1242 mode->vsync_end - mode->vsync_start); 1243 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HRES, mode->hdisplay); 1244 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VRES, mode->vdisplay); 1245 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_HSTART, 1246 mode->htotal - mode->hsync_start); 1247 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_VSTART, 1248 mode->vtotal - mode->vsync_start); 1249 1250 /* In synchronous mode, set the dividers */ 1251 if (dp->config.misc0 & ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK) { 1252 reg = drm_dp_bw_code_to_link_rate(dp->mode.bw_code); 1253 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_N_VID, reg); 1254 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_M_VID, mode->clock); 1255 rate = zynqmp_dpsub_get_audio_clk_rate(dp->dpsub); 1256 if (rate) { 1257 dev_dbg(dp->dev, "Audio rate: %d\n", rate / 512); 1258 zynqmp_dp_write(dp, ZYNQMP_DP_TX_N_AUD, reg); 1259 zynqmp_dp_write(dp, ZYNQMP_DP_TX_M_AUD, rate / 1000); 1260 } 1261 } 1262 1263 /* Only 2 channel audio is supported now */ 1264 if (zynqmp_dpsub_audio_enabled(dp->dpsub)) 1265 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CHANNELS, 1); 1266 1267 zynqmp_dp_write(dp, ZYNQMP_DP_USER_PIX_WIDTH, 1); 1268 1269 /* Translate to the native 16 bit datapath based on IP core spec */ 1270 wpl = (mode->hdisplay * dp->config.bpp + 15) / 16; 1271 reg = wpl + wpl % lane_cnt - lane_cnt; 1272 zynqmp_dp_write(dp, ZYNQMP_DP_USER_DATA_COUNT_PER_LANE, reg); 1273 } 1274 1275 /* ----------------------------------------------------------------------------- 1276 * DISP Configuration 1277 */ 1278 1279 static void zynqmp_dp_disp_enable(struct zynqmp_dp *dp, 1280 struct drm_bridge_state *old_bridge_state) 1281 { 1282 enum zynqmp_dpsub_layer_id layer_id; 1283 struct zynqmp_disp_layer *layer; 1284 const struct drm_format_info *info; 1285 1286 if (dp->dpsub->connected_ports & BIT(ZYNQMP_DPSUB_PORT_LIVE_VIDEO)) 1287 layer_id = ZYNQMP_DPSUB_LAYER_VID; 1288 else if (dp->dpsub->connected_ports & BIT(ZYNQMP_DPSUB_PORT_LIVE_GFX)) 1289 layer_id = ZYNQMP_DPSUB_LAYER_GFX; 1290 else 1291 return; 1292 1293 layer = dp->dpsub->layers[layer_id]; 1294 1295 /* TODO: Make the format configurable. */ 1296 info = drm_format_info(DRM_FORMAT_YUV422); 1297 zynqmp_disp_layer_set_format(layer, info); 1298 zynqmp_disp_layer_enable(layer, ZYNQMP_DPSUB_LAYER_LIVE); 1299 1300 if (layer_id == ZYNQMP_DPSUB_LAYER_GFX) 1301 zynqmp_disp_blend_set_global_alpha(dp->dpsub->disp, true, 255); 1302 else 1303 zynqmp_disp_blend_set_global_alpha(dp->dpsub->disp, false, 0); 1304 1305 zynqmp_disp_enable(dp->dpsub->disp); 1306 } 1307 1308 static void zynqmp_dp_disp_disable(struct zynqmp_dp *dp, 1309 struct drm_bridge_state *old_bridge_state) 1310 { 1311 struct zynqmp_disp_layer *layer; 1312 1313 if (dp->dpsub->connected_ports & BIT(ZYNQMP_DPSUB_PORT_LIVE_VIDEO)) 1314 layer = dp->dpsub->layers[ZYNQMP_DPSUB_LAYER_VID]; 1315 else if (dp->dpsub->connected_ports & BIT(ZYNQMP_DPSUB_PORT_LIVE_GFX)) 1316 layer = dp->dpsub->layers[ZYNQMP_DPSUB_LAYER_GFX]; 1317 else 1318 return; 1319 1320 zynqmp_disp_disable(dp->dpsub->disp); 1321 zynqmp_disp_layer_disable(layer); 1322 } 1323 1324 /* ----------------------------------------------------------------------------- 1325 * DRM Bridge 1326 */ 1327 1328 static int zynqmp_dp_bridge_attach(struct drm_bridge *bridge, 1329 enum drm_bridge_attach_flags flags) 1330 { 1331 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1332 int ret; 1333 1334 /* Initialize and register the AUX adapter. */ 1335 ret = zynqmp_dp_aux_init(dp); 1336 if (ret) { 1337 dev_err(dp->dev, "failed to initialize DP aux\n"); 1338 return ret; 1339 } 1340 1341 if (dp->next_bridge) { 1342 ret = drm_bridge_attach(bridge->encoder, dp->next_bridge, 1343 bridge, flags); 1344 if (ret < 0) 1345 goto error; 1346 } 1347 1348 /* Now that initialisation is complete, enable interrupts. */ 1349 zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_ALL); 1350 1351 return 0; 1352 1353 error: 1354 zynqmp_dp_aux_cleanup(dp); 1355 return ret; 1356 } 1357 1358 static void zynqmp_dp_bridge_detach(struct drm_bridge *bridge) 1359 { 1360 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1361 1362 zynqmp_dp_aux_cleanup(dp); 1363 } 1364 1365 static enum drm_mode_status 1366 zynqmp_dp_bridge_mode_valid(struct drm_bridge *bridge, 1367 const struct drm_display_info *info, 1368 const struct drm_display_mode *mode) 1369 { 1370 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1371 int rate; 1372 1373 if (mode->clock > ZYNQMP_MAX_FREQ) { 1374 dev_dbg(dp->dev, "filtered mode %s for high pixel rate\n", 1375 mode->name); 1376 drm_mode_debug_printmodeline(mode); 1377 return MODE_CLOCK_HIGH; 1378 } 1379 1380 /* Check with link rate and lane count */ 1381 rate = zynqmp_dp_max_rate(dp->link_config.max_rate, 1382 dp->link_config.max_lanes, dp->config.bpp); 1383 if (mode->clock > rate) { 1384 dev_dbg(dp->dev, "filtered mode %s for high pixel rate\n", 1385 mode->name); 1386 drm_mode_debug_printmodeline(mode); 1387 return MODE_CLOCK_HIGH; 1388 } 1389 1390 return MODE_OK; 1391 } 1392 1393 static void zynqmp_dp_bridge_atomic_enable(struct drm_bridge *bridge, 1394 struct drm_bridge_state *old_bridge_state) 1395 { 1396 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1397 struct drm_atomic_state *state = old_bridge_state->base.state; 1398 const struct drm_crtc_state *crtc_state; 1399 const struct drm_display_mode *adjusted_mode; 1400 const struct drm_display_mode *mode; 1401 struct drm_connector *connector; 1402 struct drm_crtc *crtc; 1403 unsigned int i; 1404 int rate; 1405 int ret; 1406 1407 pm_runtime_get_sync(dp->dev); 1408 1409 zynqmp_dp_disp_enable(dp, old_bridge_state); 1410 1411 /* 1412 * Retrieve the CRTC mode and adjusted mode. This requires a little 1413 * dance to go from the bridge to the encoder, to the connector and to 1414 * the CRTC. 1415 */ 1416 connector = drm_atomic_get_new_connector_for_encoder(state, 1417 bridge->encoder); 1418 crtc = drm_atomic_get_new_connector_state(state, connector)->crtc; 1419 crtc_state = drm_atomic_get_new_crtc_state(state, crtc); 1420 adjusted_mode = &crtc_state->adjusted_mode; 1421 mode = &crtc_state->mode; 1422 1423 zynqmp_dp_set_format(dp, &connector->display_info, 1424 ZYNQMP_DPSUB_FORMAT_RGB, 8); 1425 1426 /* Check again as bpp or format might have been changed */ 1427 rate = zynqmp_dp_max_rate(dp->link_config.max_rate, 1428 dp->link_config.max_lanes, dp->config.bpp); 1429 if (mode->clock > rate) { 1430 dev_err(dp->dev, "mode %s has too high pixel rate\n", 1431 mode->name); 1432 drm_mode_debug_printmodeline(mode); 1433 } 1434 1435 /* Configure the mode */ 1436 ret = zynqmp_dp_mode_configure(dp, adjusted_mode->clock, 0); 1437 if (ret < 0) { 1438 pm_runtime_put_sync(dp->dev); 1439 return; 1440 } 1441 1442 zynqmp_dp_encoder_mode_set_transfer_unit(dp, adjusted_mode); 1443 zynqmp_dp_encoder_mode_set_stream(dp, adjusted_mode); 1444 1445 /* Enable the encoder */ 1446 dp->enabled = true; 1447 zynqmp_dp_update_misc(dp); 1448 if (zynqmp_dpsub_audio_enabled(dp->dpsub)) 1449 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 1); 1450 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 0); 1451 if (dp->status == connector_status_connected) { 1452 for (i = 0; i < 3; i++) { 1453 ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, 1454 DP_SET_POWER_D0); 1455 if (ret == 1) 1456 break; 1457 usleep_range(300, 500); 1458 } 1459 /* Some monitors take time to wake up properly */ 1460 msleep(zynqmp_dp_power_on_delay_ms); 1461 } 1462 if (ret != 1) 1463 dev_dbg(dp->dev, "DP aux failed\n"); 1464 else 1465 zynqmp_dp_train_loop(dp); 1466 zynqmp_dp_write(dp, ZYNQMP_DP_SOFTWARE_RESET, 1467 ZYNQMP_DP_SOFTWARE_RESET_ALL); 1468 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 1); 1469 } 1470 1471 static void zynqmp_dp_bridge_atomic_disable(struct drm_bridge *bridge, 1472 struct drm_bridge_state *old_bridge_state) 1473 { 1474 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1475 1476 dp->enabled = false; 1477 cancel_delayed_work(&dp->hpd_work); 1478 zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 0); 1479 drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D3); 1480 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 1481 ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL); 1482 if (zynqmp_dpsub_audio_enabled(dp->dpsub)) 1483 zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 0); 1484 1485 zynqmp_dp_disp_disable(dp, old_bridge_state); 1486 1487 pm_runtime_put_sync(dp->dev); 1488 } 1489 1490 #define ZYNQMP_DP_MIN_H_BACKPORCH 20 1491 1492 static int zynqmp_dp_bridge_atomic_check(struct drm_bridge *bridge, 1493 struct drm_bridge_state *bridge_state, 1494 struct drm_crtc_state *crtc_state, 1495 struct drm_connector_state *conn_state) 1496 { 1497 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1498 struct drm_display_mode *mode = &crtc_state->mode; 1499 struct drm_display_mode *adjusted_mode = &crtc_state->adjusted_mode; 1500 int diff = mode->htotal - mode->hsync_end; 1501 1502 /* 1503 * ZynqMP DP requires horizontal backporch to be greater than 12. 1504 * This limitation may not be compatible with the sink device. 1505 */ 1506 if (diff < ZYNQMP_DP_MIN_H_BACKPORCH) { 1507 int vrefresh = (adjusted_mode->clock * 1000) / 1508 (adjusted_mode->vtotal * adjusted_mode->htotal); 1509 1510 dev_dbg(dp->dev, "hbackporch adjusted: %d to %d", 1511 diff, ZYNQMP_DP_MIN_H_BACKPORCH - diff); 1512 diff = ZYNQMP_DP_MIN_H_BACKPORCH - diff; 1513 adjusted_mode->htotal += diff; 1514 adjusted_mode->clock = adjusted_mode->vtotal * 1515 adjusted_mode->htotal * vrefresh / 1000; 1516 } 1517 1518 return 0; 1519 } 1520 1521 static enum drm_connector_status zynqmp_dp_bridge_detect(struct drm_bridge *bridge) 1522 { 1523 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1524 struct zynqmp_dp_link_config *link_config = &dp->link_config; 1525 u32 state, i; 1526 int ret; 1527 1528 /* 1529 * This is from heuristic. It takes some delay (ex, 100 ~ 500 msec) to 1530 * get the HPD signal with some monitors. 1531 */ 1532 for (i = 0; i < 10; i++) { 1533 state = zynqmp_dp_read(dp, ZYNQMP_DP_INTERRUPT_SIGNAL_STATE); 1534 if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD) 1535 break; 1536 msleep(100); 1537 } 1538 1539 if (state & ZYNQMP_DP_INTERRUPT_SIGNAL_STATE_HPD) { 1540 ret = drm_dp_dpcd_read(&dp->aux, 0x0, dp->dpcd, 1541 sizeof(dp->dpcd)); 1542 if (ret < 0) { 1543 dev_dbg(dp->dev, "DPCD read failed"); 1544 goto disconnected; 1545 } 1546 1547 link_config->max_rate = min_t(int, 1548 drm_dp_max_link_rate(dp->dpcd), 1549 DP_HIGH_BIT_RATE2); 1550 link_config->max_lanes = min_t(u8, 1551 drm_dp_max_lane_count(dp->dpcd), 1552 dp->num_lanes); 1553 1554 dp->status = connector_status_connected; 1555 return connector_status_connected; 1556 } 1557 1558 disconnected: 1559 dp->status = connector_status_disconnected; 1560 return connector_status_disconnected; 1561 } 1562 1563 static struct edid *zynqmp_dp_bridge_get_edid(struct drm_bridge *bridge, 1564 struct drm_connector *connector) 1565 { 1566 struct zynqmp_dp *dp = bridge_to_dp(bridge); 1567 1568 return drm_get_edid(connector, &dp->aux.ddc); 1569 } 1570 1571 static const struct drm_bridge_funcs zynqmp_dp_bridge_funcs = { 1572 .attach = zynqmp_dp_bridge_attach, 1573 .detach = zynqmp_dp_bridge_detach, 1574 .mode_valid = zynqmp_dp_bridge_mode_valid, 1575 .atomic_enable = zynqmp_dp_bridge_atomic_enable, 1576 .atomic_disable = zynqmp_dp_bridge_atomic_disable, 1577 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 1578 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 1579 .atomic_reset = drm_atomic_helper_bridge_reset, 1580 .atomic_check = zynqmp_dp_bridge_atomic_check, 1581 .detect = zynqmp_dp_bridge_detect, 1582 .get_edid = zynqmp_dp_bridge_get_edid, 1583 }; 1584 1585 /* ----------------------------------------------------------------------------- 1586 * Interrupt Handling 1587 */ 1588 1589 /** 1590 * zynqmp_dp_enable_vblank - Enable vblank 1591 * @dp: DisplayPort IP core structure 1592 * 1593 * Enable vblank interrupt 1594 */ 1595 void zynqmp_dp_enable_vblank(struct zynqmp_dp *dp) 1596 { 1597 zynqmp_dp_write(dp, ZYNQMP_DP_INT_EN, ZYNQMP_DP_INT_VBLANK_START); 1598 } 1599 1600 /** 1601 * zynqmp_dp_disable_vblank - Disable vblank 1602 * @dp: DisplayPort IP core structure 1603 * 1604 * Disable vblank interrupt 1605 */ 1606 void zynqmp_dp_disable_vblank(struct zynqmp_dp *dp) 1607 { 1608 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_VBLANK_START); 1609 } 1610 1611 static void zynqmp_dp_hpd_work_func(struct work_struct *work) 1612 { 1613 struct zynqmp_dp *dp = container_of(work, struct zynqmp_dp, 1614 hpd_work.work); 1615 enum drm_connector_status status; 1616 1617 status = zynqmp_dp_bridge_detect(&dp->bridge); 1618 drm_bridge_hpd_notify(&dp->bridge, status); 1619 } 1620 1621 static irqreturn_t zynqmp_dp_irq_handler(int irq, void *data) 1622 { 1623 struct zynqmp_dp *dp = (struct zynqmp_dp *)data; 1624 u32 status, mask; 1625 1626 status = zynqmp_dp_read(dp, ZYNQMP_DP_INT_STATUS); 1627 mask = zynqmp_dp_read(dp, ZYNQMP_DP_INT_MASK); 1628 if (!(status & ~mask)) 1629 return IRQ_NONE; 1630 1631 /* dbg for diagnostic, but not much that the driver can do */ 1632 if (status & ZYNQMP_DP_INT_CHBUF_UNDERFLW_MASK) 1633 dev_dbg_ratelimited(dp->dev, "underflow interrupt\n"); 1634 if (status & ZYNQMP_DP_INT_CHBUF_OVERFLW_MASK) 1635 dev_dbg_ratelimited(dp->dev, "overflow interrupt\n"); 1636 1637 zynqmp_dp_write(dp, ZYNQMP_DP_INT_STATUS, status); 1638 1639 if (status & ZYNQMP_DP_INT_VBLANK_START) 1640 zynqmp_dpsub_drm_handle_vblank(dp->dpsub); 1641 1642 if (status & ZYNQMP_DP_INT_HPD_EVENT) 1643 schedule_delayed_work(&dp->hpd_work, 0); 1644 1645 if (status & ZYNQMP_DP_INT_HPD_IRQ) { 1646 int ret; 1647 u8 status[DP_LINK_STATUS_SIZE + 2]; 1648 1649 ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, status, 1650 DP_LINK_STATUS_SIZE + 2); 1651 if (ret < 0) 1652 goto handled; 1653 1654 if (status[4] & DP_LINK_STATUS_UPDATED || 1655 !drm_dp_clock_recovery_ok(&status[2], dp->mode.lane_cnt) || 1656 !drm_dp_channel_eq_ok(&status[2], dp->mode.lane_cnt)) { 1657 zynqmp_dp_train_loop(dp); 1658 } 1659 } 1660 1661 handled: 1662 return IRQ_HANDLED; 1663 } 1664 1665 /* ----------------------------------------------------------------------------- 1666 * Initialization & Cleanup 1667 */ 1668 1669 int zynqmp_dp_probe(struct zynqmp_dpsub *dpsub) 1670 { 1671 struct platform_device *pdev = to_platform_device(dpsub->dev); 1672 struct drm_bridge *bridge; 1673 struct zynqmp_dp *dp; 1674 struct resource *res; 1675 int ret; 1676 1677 dp = kzalloc(sizeof(*dp), GFP_KERNEL); 1678 if (!dp) 1679 return -ENOMEM; 1680 1681 dp->dev = &pdev->dev; 1682 dp->dpsub = dpsub; 1683 dp->status = connector_status_disconnected; 1684 1685 INIT_DELAYED_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func); 1686 1687 /* Acquire all resources (IOMEM, IRQ and PHYs). */ 1688 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dp"); 1689 dp->iomem = devm_ioremap_resource(dp->dev, res); 1690 if (IS_ERR(dp->iomem)) { 1691 ret = PTR_ERR(dp->iomem); 1692 goto err_free; 1693 } 1694 1695 dp->irq = platform_get_irq(pdev, 0); 1696 if (dp->irq < 0) { 1697 ret = dp->irq; 1698 goto err_free; 1699 } 1700 1701 dp->reset = devm_reset_control_get(dp->dev, NULL); 1702 if (IS_ERR(dp->reset)) { 1703 if (PTR_ERR(dp->reset) != -EPROBE_DEFER) 1704 dev_err(dp->dev, "failed to get reset: %ld\n", 1705 PTR_ERR(dp->reset)); 1706 ret = PTR_ERR(dp->reset); 1707 goto err_free; 1708 } 1709 1710 ret = zynqmp_dp_reset(dp, false); 1711 if (ret < 0) 1712 goto err_free; 1713 1714 ret = zynqmp_dp_phy_probe(dp); 1715 if (ret) 1716 goto err_reset; 1717 1718 /* Initialize the bridge. */ 1719 bridge = &dp->bridge; 1720 bridge->funcs = &zynqmp_dp_bridge_funcs; 1721 bridge->ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID 1722 | DRM_BRIDGE_OP_HPD; 1723 bridge->type = DRM_MODE_CONNECTOR_DisplayPort; 1724 dpsub->bridge = bridge; 1725 1726 /* 1727 * Acquire the next bridge in the chain. Ignore errors caused by port@5 1728 * not being connected for backward-compatibility with older DTs. 1729 */ 1730 ret = drm_of_find_panel_or_bridge(dp->dev->of_node, 5, 0, NULL, 1731 &dp->next_bridge); 1732 if (ret < 0 && ret != -ENODEV) 1733 goto err_reset; 1734 1735 /* Initialize the hardware. */ 1736 dp->config.misc0 &= ~ZYNQMP_DP_MAIN_STREAM_MISC0_SYNC_LOCK; 1737 zynqmp_dp_set_format(dp, NULL, ZYNQMP_DPSUB_FORMAT_RGB, 8); 1738 1739 zynqmp_dp_write(dp, ZYNQMP_DP_TX_PHY_POWER_DOWN, 1740 ZYNQMP_DP_TX_PHY_POWER_DOWN_ALL); 1741 zynqmp_dp_set(dp, ZYNQMP_DP_PHY_RESET, ZYNQMP_DP_PHY_RESET_ALL_RESET); 1742 zynqmp_dp_write(dp, ZYNQMP_DP_FORCE_SCRAMBLER_RESET, 1); 1743 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0); 1744 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff); 1745 1746 ret = zynqmp_dp_phy_init(dp); 1747 if (ret) 1748 goto err_reset; 1749 1750 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 1); 1751 1752 /* 1753 * Now that the hardware is initialized and won't generate spurious 1754 * interrupts, request the IRQ. 1755 */ 1756 ret = devm_request_threaded_irq(dp->dev, dp->irq, NULL, 1757 zynqmp_dp_irq_handler, IRQF_ONESHOT, 1758 dev_name(dp->dev), dp); 1759 if (ret < 0) 1760 goto err_phy_exit; 1761 1762 dpsub->dp = dp; 1763 1764 dev_dbg(dp->dev, "ZynqMP DisplayPort Tx probed with %u lanes\n", 1765 dp->num_lanes); 1766 1767 return 0; 1768 1769 err_phy_exit: 1770 zynqmp_dp_phy_exit(dp); 1771 err_reset: 1772 zynqmp_dp_reset(dp, true); 1773 err_free: 1774 kfree(dp); 1775 return ret; 1776 } 1777 1778 void zynqmp_dp_remove(struct zynqmp_dpsub *dpsub) 1779 { 1780 struct zynqmp_dp *dp = dpsub->dp; 1781 1782 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, ZYNQMP_DP_INT_ALL); 1783 disable_irq(dp->irq); 1784 1785 cancel_delayed_work_sync(&dp->hpd_work); 1786 1787 zynqmp_dp_write(dp, ZYNQMP_DP_TRANSMITTER_ENABLE, 0); 1788 zynqmp_dp_write(dp, ZYNQMP_DP_INT_DS, 0xffffffff); 1789 1790 zynqmp_dp_phy_exit(dp); 1791 zynqmp_dp_reset(dp, true); 1792 } 1793