1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2016 Broadcom Limited 4 */ 5 6 /** 7 * DOC: VC4 DPI module 8 * 9 * The VC4 DPI hardware supports MIPI DPI type 4 and Nokia ViSSI 10 * signals. On BCM2835, these can be routed out to GPIO0-27 with the 11 * ALT2 function. 12 */ 13 14 #include <drm/drm_atomic_helper.h> 15 #include <drm/drm_bridge.h> 16 #include <drm/drm_edid.h> 17 #include <drm/drm_of.h> 18 #include <drm/drm_panel.h> 19 #include <drm/drm_probe_helper.h> 20 #include <linux/clk.h> 21 #include <linux/component.h> 22 #include <linux/of_graph.h> 23 #include <linux/of_platform.h> 24 #include "vc4_drv.h" 25 #include "vc4_regs.h" 26 27 #define DPI_C 0x00 28 # define DPI_OUTPUT_ENABLE_MODE BIT(16) 29 30 /* The order field takes the incoming 24 bit RGB from the pixel valve 31 * and shuffles the 3 channels. 32 */ 33 # define DPI_ORDER_MASK VC4_MASK(15, 14) 34 # define DPI_ORDER_SHIFT 14 35 # define DPI_ORDER_RGB 0 36 # define DPI_ORDER_BGR 1 37 # define DPI_ORDER_GRB 2 38 # define DPI_ORDER_BRG 3 39 40 /* The format field takes the ORDER-shuffled pixel valve data and 41 * formats it onto the output lines. 42 */ 43 # define DPI_FORMAT_MASK VC4_MASK(13, 11) 44 # define DPI_FORMAT_SHIFT 11 45 /* This define is named in the hardware, but actually just outputs 0. */ 46 # define DPI_FORMAT_9BIT_666_RGB 0 47 /* Outputs 00000000rrrrrggggggbbbbb */ 48 # define DPI_FORMAT_16BIT_565_RGB_1 1 49 /* Outputs 000rrrrr00gggggg000bbbbb */ 50 # define DPI_FORMAT_16BIT_565_RGB_2 2 51 /* Outputs 00rrrrr000gggggg00bbbbb0 */ 52 # define DPI_FORMAT_16BIT_565_RGB_3 3 53 /* Outputs 000000rrrrrrggggggbbbbbb */ 54 # define DPI_FORMAT_18BIT_666_RGB_1 4 55 /* Outputs 00rrrrrr00gggggg00bbbbbb */ 56 # define DPI_FORMAT_18BIT_666_RGB_2 5 57 /* Outputs rrrrrrrrggggggggbbbbbbbb */ 58 # define DPI_FORMAT_24BIT_888_RGB 6 59 60 /* Reverses the polarity of the corresponding signal */ 61 # define DPI_PIXEL_CLK_INVERT BIT(10) 62 # define DPI_HSYNC_INVERT BIT(9) 63 # define DPI_VSYNC_INVERT BIT(8) 64 # define DPI_OUTPUT_ENABLE_INVERT BIT(7) 65 66 /* Outputs the signal the falling clock edge instead of rising. */ 67 # define DPI_HSYNC_NEGATE BIT(6) 68 # define DPI_VSYNC_NEGATE BIT(5) 69 # define DPI_OUTPUT_ENABLE_NEGATE BIT(4) 70 71 /* Disables the signal */ 72 # define DPI_HSYNC_DISABLE BIT(3) 73 # define DPI_VSYNC_DISABLE BIT(2) 74 # define DPI_OUTPUT_ENABLE_DISABLE BIT(1) 75 76 /* Power gate to the device, full reset at 0 -> 1 transition */ 77 # define DPI_ENABLE BIT(0) 78 79 /* All other registers besides DPI_C return the ID */ 80 #define DPI_ID 0x04 81 # define DPI_ID_VALUE 0x00647069 82 83 /* General DPI hardware state. */ 84 struct vc4_dpi { 85 struct platform_device *pdev; 86 87 struct drm_encoder *encoder; 88 89 void __iomem *regs; 90 91 struct clk *pixel_clock; 92 struct clk *core_clock; 93 94 struct debugfs_regset32 regset; 95 }; 96 97 #define DPI_READ(offset) readl(dpi->regs + (offset)) 98 #define DPI_WRITE(offset, val) writel(val, dpi->regs + (offset)) 99 100 /* VC4 DPI encoder KMS struct */ 101 struct vc4_dpi_encoder { 102 struct vc4_encoder base; 103 struct vc4_dpi *dpi; 104 }; 105 106 static inline struct vc4_dpi_encoder * 107 to_vc4_dpi_encoder(struct drm_encoder *encoder) 108 { 109 return container_of(encoder, struct vc4_dpi_encoder, base.base); 110 } 111 112 static const struct debugfs_reg32 dpi_regs[] = { 113 VC4_REG32(DPI_C), 114 VC4_REG32(DPI_ID), 115 }; 116 117 static const struct drm_encoder_funcs vc4_dpi_encoder_funcs = { 118 .destroy = drm_encoder_cleanup, 119 }; 120 121 static void vc4_dpi_encoder_disable(struct drm_encoder *encoder) 122 { 123 struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder); 124 struct vc4_dpi *dpi = vc4_encoder->dpi; 125 126 clk_disable_unprepare(dpi->pixel_clock); 127 } 128 129 static void vc4_dpi_encoder_enable(struct drm_encoder *encoder) 130 { 131 struct drm_device *dev = encoder->dev; 132 struct drm_display_mode *mode = &encoder->crtc->mode; 133 struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder); 134 struct vc4_dpi *dpi = vc4_encoder->dpi; 135 struct drm_connector_list_iter conn_iter; 136 struct drm_connector *connector = NULL, *connector_scan; 137 u32 dpi_c = DPI_ENABLE | DPI_OUTPUT_ENABLE_MODE; 138 int ret; 139 140 /* Look up the connector attached to DPI so we can get the 141 * bus_format. Ideally the bridge would tell us the 142 * bus_format we want, but it doesn't yet, so assume that it's 143 * uniform throughout the bridge chain. 144 */ 145 drm_connector_list_iter_begin(dev, &conn_iter); 146 drm_for_each_connector_iter(connector_scan, &conn_iter) { 147 if (connector_scan->encoder == encoder) { 148 connector = connector_scan; 149 break; 150 } 151 } 152 drm_connector_list_iter_end(&conn_iter); 153 154 if (connector && connector->display_info.num_bus_formats) { 155 u32 bus_format = connector->display_info.bus_formats[0]; 156 157 switch (bus_format) { 158 case MEDIA_BUS_FMT_RGB888_1X24: 159 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, 160 DPI_FORMAT); 161 break; 162 case MEDIA_BUS_FMT_BGR888_1X24: 163 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, 164 DPI_FORMAT); 165 dpi_c |= VC4_SET_FIELD(DPI_ORDER_BGR, DPI_ORDER); 166 break; 167 case MEDIA_BUS_FMT_RGB666_1X24_CPADHI: 168 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_2, 169 DPI_FORMAT); 170 break; 171 case MEDIA_BUS_FMT_RGB666_1X18: 172 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_1, 173 DPI_FORMAT); 174 break; 175 case MEDIA_BUS_FMT_RGB565_1X16: 176 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_16BIT_565_RGB_3, 177 DPI_FORMAT); 178 break; 179 default: 180 DRM_ERROR("Unknown media bus format %d\n", bus_format); 181 break; 182 } 183 } else { 184 /* Default to 24bit if no connector found. */ 185 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, DPI_FORMAT); 186 } 187 188 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 189 dpi_c |= DPI_HSYNC_INVERT; 190 else if (!(mode->flags & DRM_MODE_FLAG_PHSYNC)) 191 dpi_c |= DPI_HSYNC_DISABLE; 192 193 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 194 dpi_c |= DPI_VSYNC_INVERT; 195 else if (!(mode->flags & DRM_MODE_FLAG_PVSYNC)) 196 dpi_c |= DPI_VSYNC_DISABLE; 197 198 DPI_WRITE(DPI_C, dpi_c); 199 200 ret = clk_set_rate(dpi->pixel_clock, mode->clock * 1000); 201 if (ret) 202 DRM_ERROR("Failed to set clock rate: %d\n", ret); 203 204 ret = clk_prepare_enable(dpi->pixel_clock); 205 if (ret) 206 DRM_ERROR("Failed to set clock rate: %d\n", ret); 207 } 208 209 static enum drm_mode_status vc4_dpi_encoder_mode_valid(struct drm_encoder *encoder, 210 const struct drm_display_mode *mode) 211 { 212 if (mode->flags & DRM_MODE_FLAG_INTERLACE) 213 return MODE_NO_INTERLACE; 214 215 return MODE_OK; 216 } 217 218 static const struct drm_encoder_helper_funcs vc4_dpi_encoder_helper_funcs = { 219 .disable = vc4_dpi_encoder_disable, 220 .enable = vc4_dpi_encoder_enable, 221 .mode_valid = vc4_dpi_encoder_mode_valid, 222 }; 223 224 static const struct of_device_id vc4_dpi_dt_match[] = { 225 { .compatible = "brcm,bcm2835-dpi", .data = NULL }, 226 {} 227 }; 228 229 /* Sets up the next link in the display chain, whether it's a panel or 230 * a bridge. 231 */ 232 static int vc4_dpi_init_bridge(struct vc4_dpi *dpi) 233 { 234 struct device *dev = &dpi->pdev->dev; 235 struct drm_panel *panel; 236 struct drm_bridge *bridge; 237 int ret; 238 239 ret = drm_of_find_panel_or_bridge(dev->of_node, 0, 0, 240 &panel, &bridge); 241 if (ret) { 242 /* If nothing was connected in the DT, that's not an 243 * error. 244 */ 245 if (ret == -ENODEV) 246 return 0; 247 else 248 return ret; 249 } 250 251 if (panel) 252 bridge = drm_panel_bridge_add_typed(panel, 253 DRM_MODE_CONNECTOR_DPI); 254 255 return drm_bridge_attach(dpi->encoder, bridge, NULL); 256 } 257 258 static int vc4_dpi_bind(struct device *dev, struct device *master, void *data) 259 { 260 struct platform_device *pdev = to_platform_device(dev); 261 struct drm_device *drm = dev_get_drvdata(master); 262 struct vc4_dev *vc4 = to_vc4_dev(drm); 263 struct vc4_dpi *dpi; 264 struct vc4_dpi_encoder *vc4_dpi_encoder; 265 int ret; 266 267 dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL); 268 if (!dpi) 269 return -ENOMEM; 270 271 vc4_dpi_encoder = devm_kzalloc(dev, sizeof(*vc4_dpi_encoder), 272 GFP_KERNEL); 273 if (!vc4_dpi_encoder) 274 return -ENOMEM; 275 vc4_dpi_encoder->base.type = VC4_ENCODER_TYPE_DPI; 276 vc4_dpi_encoder->dpi = dpi; 277 dpi->encoder = &vc4_dpi_encoder->base.base; 278 279 dpi->pdev = pdev; 280 dpi->regs = vc4_ioremap_regs(pdev, 0); 281 if (IS_ERR(dpi->regs)) 282 return PTR_ERR(dpi->regs); 283 dpi->regset.base = dpi->regs; 284 dpi->regset.regs = dpi_regs; 285 dpi->regset.nregs = ARRAY_SIZE(dpi_regs); 286 287 if (DPI_READ(DPI_ID) != DPI_ID_VALUE) { 288 dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n", 289 DPI_READ(DPI_ID), DPI_ID_VALUE); 290 return -ENODEV; 291 } 292 293 dpi->core_clock = devm_clk_get(dev, "core"); 294 if (IS_ERR(dpi->core_clock)) { 295 ret = PTR_ERR(dpi->core_clock); 296 if (ret != -EPROBE_DEFER) 297 DRM_ERROR("Failed to get core clock: %d\n", ret); 298 return ret; 299 } 300 dpi->pixel_clock = devm_clk_get(dev, "pixel"); 301 if (IS_ERR(dpi->pixel_clock)) { 302 ret = PTR_ERR(dpi->pixel_clock); 303 if (ret != -EPROBE_DEFER) 304 DRM_ERROR("Failed to get pixel clock: %d\n", ret); 305 return ret; 306 } 307 308 ret = clk_prepare_enable(dpi->core_clock); 309 if (ret) 310 DRM_ERROR("Failed to turn on core clock: %d\n", ret); 311 312 drm_encoder_init(drm, dpi->encoder, &vc4_dpi_encoder_funcs, 313 DRM_MODE_ENCODER_DPI, NULL); 314 drm_encoder_helper_add(dpi->encoder, &vc4_dpi_encoder_helper_funcs); 315 316 ret = vc4_dpi_init_bridge(dpi); 317 if (ret) 318 goto err_destroy_encoder; 319 320 dev_set_drvdata(dev, dpi); 321 322 vc4->dpi = dpi; 323 324 vc4_debugfs_add_regset32(drm, "dpi_regs", &dpi->regset); 325 326 return 0; 327 328 err_destroy_encoder: 329 drm_encoder_cleanup(dpi->encoder); 330 clk_disable_unprepare(dpi->core_clock); 331 return ret; 332 } 333 334 static void vc4_dpi_unbind(struct device *dev, struct device *master, 335 void *data) 336 { 337 struct drm_device *drm = dev_get_drvdata(master); 338 struct vc4_dev *vc4 = to_vc4_dev(drm); 339 struct vc4_dpi *dpi = dev_get_drvdata(dev); 340 341 drm_of_panel_bridge_remove(dev->of_node, 0, 0); 342 343 drm_encoder_cleanup(dpi->encoder); 344 345 clk_disable_unprepare(dpi->core_clock); 346 347 vc4->dpi = NULL; 348 } 349 350 static const struct component_ops vc4_dpi_ops = { 351 .bind = vc4_dpi_bind, 352 .unbind = vc4_dpi_unbind, 353 }; 354 355 static int vc4_dpi_dev_probe(struct platform_device *pdev) 356 { 357 return component_add(&pdev->dev, &vc4_dpi_ops); 358 } 359 360 static int vc4_dpi_dev_remove(struct platform_device *pdev) 361 { 362 component_del(&pdev->dev, &vc4_dpi_ops); 363 return 0; 364 } 365 366 struct platform_driver vc4_dpi_driver = { 367 .probe = vc4_dpi_dev_probe, 368 .remove = vc4_dpi_dev_remove, 369 .driver = { 370 .name = "vc4_dpi", 371 .of_match_table = vc4_dpi_dt_match, 372 }, 373 }; 374