1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2016 Broadcom Limited 4 */ 5 6 /** 7 * DOC: VC4 DPI module 8 * 9 * The VC4 DPI hardware supports MIPI DPI type 4 and Nokia ViSSI 10 * signals. On BCM2835, these can be routed out to GPIO0-27 with the 11 * ALT2 function. 12 */ 13 14 #include <drm/drm_atomic_helper.h> 15 #include <drm/drm_bridge.h> 16 #include <drm/drm_edid.h> 17 #include <drm/drm_of.h> 18 #include <drm/drm_panel.h> 19 #include <drm/drm_probe_helper.h> 20 #include <drm/drm_simple_kms_helper.h> 21 #include <linux/clk.h> 22 #include <linux/component.h> 23 #include <linux/of_graph.h> 24 #include <linux/of_platform.h> 25 #include "vc4_drv.h" 26 #include "vc4_regs.h" 27 28 #define DPI_C 0x00 29 # define DPI_OUTPUT_ENABLE_MODE BIT(16) 30 31 /* The order field takes the incoming 24 bit RGB from the pixel valve 32 * and shuffles the 3 channels. 33 */ 34 # define DPI_ORDER_MASK VC4_MASK(15, 14) 35 # define DPI_ORDER_SHIFT 14 36 # define DPI_ORDER_RGB 0 37 # define DPI_ORDER_BGR 1 38 # define DPI_ORDER_GRB 2 39 # define DPI_ORDER_BRG 3 40 41 /* The format field takes the ORDER-shuffled pixel valve data and 42 * formats it onto the output lines. 43 */ 44 # define DPI_FORMAT_MASK VC4_MASK(13, 11) 45 # define DPI_FORMAT_SHIFT 11 46 /* This define is named in the hardware, but actually just outputs 0. */ 47 # define DPI_FORMAT_9BIT_666_RGB 0 48 /* Outputs 00000000rrrrrggggggbbbbb */ 49 # define DPI_FORMAT_16BIT_565_RGB_1 1 50 /* Outputs 000rrrrr00gggggg000bbbbb */ 51 # define DPI_FORMAT_16BIT_565_RGB_2 2 52 /* Outputs 00rrrrr000gggggg00bbbbb0 */ 53 # define DPI_FORMAT_16BIT_565_RGB_3 3 54 /* Outputs 000000rrrrrrggggggbbbbbb */ 55 # define DPI_FORMAT_18BIT_666_RGB_1 4 56 /* Outputs 00rrrrrr00gggggg00bbbbbb */ 57 # define DPI_FORMAT_18BIT_666_RGB_2 5 58 /* Outputs rrrrrrrrggggggggbbbbbbbb */ 59 # define DPI_FORMAT_24BIT_888_RGB 6 60 61 /* Reverses the polarity of the corresponding signal */ 62 # define DPI_PIXEL_CLK_INVERT BIT(10) 63 # define DPI_HSYNC_INVERT BIT(9) 64 # define DPI_VSYNC_INVERT BIT(8) 65 # define DPI_OUTPUT_ENABLE_INVERT BIT(7) 66 67 /* Outputs the signal the falling clock edge instead of rising. */ 68 # define DPI_HSYNC_NEGATE BIT(6) 69 # define DPI_VSYNC_NEGATE BIT(5) 70 # define DPI_OUTPUT_ENABLE_NEGATE BIT(4) 71 72 /* Disables the signal */ 73 # define DPI_HSYNC_DISABLE BIT(3) 74 # define DPI_VSYNC_DISABLE BIT(2) 75 # define DPI_OUTPUT_ENABLE_DISABLE BIT(1) 76 77 /* Power gate to the device, full reset at 0 -> 1 transition */ 78 # define DPI_ENABLE BIT(0) 79 80 /* All other registers besides DPI_C return the ID */ 81 #define DPI_ID 0x04 82 # define DPI_ID_VALUE 0x00647069 83 84 /* General DPI hardware state. */ 85 struct vc4_dpi { 86 struct platform_device *pdev; 87 88 struct drm_encoder *encoder; 89 90 void __iomem *regs; 91 92 struct clk *pixel_clock; 93 struct clk *core_clock; 94 95 struct debugfs_regset32 regset; 96 }; 97 98 #define DPI_READ(offset) readl(dpi->regs + (offset)) 99 #define DPI_WRITE(offset, val) writel(val, dpi->regs + (offset)) 100 101 /* VC4 DPI encoder KMS struct */ 102 struct vc4_dpi_encoder { 103 struct vc4_encoder base; 104 struct vc4_dpi *dpi; 105 }; 106 107 static inline struct vc4_dpi_encoder * 108 to_vc4_dpi_encoder(struct drm_encoder *encoder) 109 { 110 return container_of(encoder, struct vc4_dpi_encoder, base.base); 111 } 112 113 static const struct debugfs_reg32 dpi_regs[] = { 114 VC4_REG32(DPI_C), 115 VC4_REG32(DPI_ID), 116 }; 117 118 static void vc4_dpi_encoder_disable(struct drm_encoder *encoder) 119 { 120 struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder); 121 struct vc4_dpi *dpi = vc4_encoder->dpi; 122 123 clk_disable_unprepare(dpi->pixel_clock); 124 } 125 126 static void vc4_dpi_encoder_enable(struct drm_encoder *encoder) 127 { 128 struct drm_device *dev = encoder->dev; 129 struct drm_display_mode *mode = &encoder->crtc->mode; 130 struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder); 131 struct vc4_dpi *dpi = vc4_encoder->dpi; 132 struct drm_connector_list_iter conn_iter; 133 struct drm_connector *connector = NULL, *connector_scan; 134 u32 dpi_c = DPI_ENABLE | DPI_OUTPUT_ENABLE_MODE; 135 int ret; 136 137 /* Look up the connector attached to DPI so we can get the 138 * bus_format. Ideally the bridge would tell us the 139 * bus_format we want, but it doesn't yet, so assume that it's 140 * uniform throughout the bridge chain. 141 */ 142 drm_connector_list_iter_begin(dev, &conn_iter); 143 drm_for_each_connector_iter(connector_scan, &conn_iter) { 144 if (connector_scan->encoder == encoder) { 145 connector = connector_scan; 146 break; 147 } 148 } 149 drm_connector_list_iter_end(&conn_iter); 150 151 if (connector && connector->display_info.num_bus_formats) { 152 u32 bus_format = connector->display_info.bus_formats[0]; 153 154 switch (bus_format) { 155 case MEDIA_BUS_FMT_RGB888_1X24: 156 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, 157 DPI_FORMAT); 158 break; 159 case MEDIA_BUS_FMT_BGR888_1X24: 160 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, 161 DPI_FORMAT); 162 dpi_c |= VC4_SET_FIELD(DPI_ORDER_BGR, DPI_ORDER); 163 break; 164 case MEDIA_BUS_FMT_RGB666_1X24_CPADHI: 165 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_2, 166 DPI_FORMAT); 167 break; 168 case MEDIA_BUS_FMT_RGB666_1X18: 169 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_1, 170 DPI_FORMAT); 171 break; 172 case MEDIA_BUS_FMT_RGB565_1X16: 173 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_16BIT_565_RGB_3, 174 DPI_FORMAT); 175 break; 176 default: 177 DRM_ERROR("Unknown media bus format %d\n", bus_format); 178 break; 179 } 180 } else { 181 /* Default to 24bit if no connector found. */ 182 dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB, DPI_FORMAT); 183 } 184 185 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 186 dpi_c |= DPI_HSYNC_INVERT; 187 else if (!(mode->flags & DRM_MODE_FLAG_PHSYNC)) 188 dpi_c |= DPI_HSYNC_DISABLE; 189 190 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 191 dpi_c |= DPI_VSYNC_INVERT; 192 else if (!(mode->flags & DRM_MODE_FLAG_PVSYNC)) 193 dpi_c |= DPI_VSYNC_DISABLE; 194 195 DPI_WRITE(DPI_C, dpi_c); 196 197 ret = clk_set_rate(dpi->pixel_clock, mode->clock * 1000); 198 if (ret) 199 DRM_ERROR("Failed to set clock rate: %d\n", ret); 200 201 ret = clk_prepare_enable(dpi->pixel_clock); 202 if (ret) 203 DRM_ERROR("Failed to set clock rate: %d\n", ret); 204 } 205 206 static enum drm_mode_status vc4_dpi_encoder_mode_valid(struct drm_encoder *encoder, 207 const struct drm_display_mode *mode) 208 { 209 if (mode->flags & DRM_MODE_FLAG_INTERLACE) 210 return MODE_NO_INTERLACE; 211 212 return MODE_OK; 213 } 214 215 static const struct drm_encoder_helper_funcs vc4_dpi_encoder_helper_funcs = { 216 .disable = vc4_dpi_encoder_disable, 217 .enable = vc4_dpi_encoder_enable, 218 .mode_valid = vc4_dpi_encoder_mode_valid, 219 }; 220 221 static const struct of_device_id vc4_dpi_dt_match[] = { 222 { .compatible = "brcm,bcm2835-dpi", .data = NULL }, 223 {} 224 }; 225 226 /* Sets up the next link in the display chain, whether it's a panel or 227 * a bridge. 228 */ 229 static int vc4_dpi_init_bridge(struct vc4_dpi *dpi) 230 { 231 struct device *dev = &dpi->pdev->dev; 232 struct drm_panel *panel; 233 struct drm_bridge *bridge; 234 int ret; 235 236 ret = drm_of_find_panel_or_bridge(dev->of_node, 0, 0, 237 &panel, &bridge); 238 if (ret) { 239 /* If nothing was connected in the DT, that's not an 240 * error. 241 */ 242 if (ret == -ENODEV) 243 return 0; 244 else 245 return ret; 246 } 247 248 if (panel) 249 bridge = drm_panel_bridge_add_typed(panel, 250 DRM_MODE_CONNECTOR_DPI); 251 252 return drm_bridge_attach(dpi->encoder, bridge, NULL, 0); 253 } 254 255 static int vc4_dpi_bind(struct device *dev, struct device *master, void *data) 256 { 257 struct platform_device *pdev = to_platform_device(dev); 258 struct drm_device *drm = dev_get_drvdata(master); 259 struct vc4_dev *vc4 = to_vc4_dev(drm); 260 struct vc4_dpi *dpi; 261 struct vc4_dpi_encoder *vc4_dpi_encoder; 262 int ret; 263 264 dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL); 265 if (!dpi) 266 return -ENOMEM; 267 268 vc4_dpi_encoder = devm_kzalloc(dev, sizeof(*vc4_dpi_encoder), 269 GFP_KERNEL); 270 if (!vc4_dpi_encoder) 271 return -ENOMEM; 272 vc4_dpi_encoder->base.type = VC4_ENCODER_TYPE_DPI; 273 vc4_dpi_encoder->dpi = dpi; 274 dpi->encoder = &vc4_dpi_encoder->base.base; 275 276 dpi->pdev = pdev; 277 dpi->regs = vc4_ioremap_regs(pdev, 0); 278 if (IS_ERR(dpi->regs)) 279 return PTR_ERR(dpi->regs); 280 dpi->regset.base = dpi->regs; 281 dpi->regset.regs = dpi_regs; 282 dpi->regset.nregs = ARRAY_SIZE(dpi_regs); 283 284 if (DPI_READ(DPI_ID) != DPI_ID_VALUE) { 285 dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n", 286 DPI_READ(DPI_ID), DPI_ID_VALUE); 287 return -ENODEV; 288 } 289 290 dpi->core_clock = devm_clk_get(dev, "core"); 291 if (IS_ERR(dpi->core_clock)) { 292 ret = PTR_ERR(dpi->core_clock); 293 if (ret != -EPROBE_DEFER) 294 DRM_ERROR("Failed to get core clock: %d\n", ret); 295 return ret; 296 } 297 dpi->pixel_clock = devm_clk_get(dev, "pixel"); 298 if (IS_ERR(dpi->pixel_clock)) { 299 ret = PTR_ERR(dpi->pixel_clock); 300 if (ret != -EPROBE_DEFER) 301 DRM_ERROR("Failed to get pixel clock: %d\n", ret); 302 return ret; 303 } 304 305 ret = clk_prepare_enable(dpi->core_clock); 306 if (ret) 307 DRM_ERROR("Failed to turn on core clock: %d\n", ret); 308 309 drm_simple_encoder_init(drm, dpi->encoder, DRM_MODE_ENCODER_DPI); 310 drm_encoder_helper_add(dpi->encoder, &vc4_dpi_encoder_helper_funcs); 311 312 ret = vc4_dpi_init_bridge(dpi); 313 if (ret) 314 goto err_destroy_encoder; 315 316 dev_set_drvdata(dev, dpi); 317 318 vc4->dpi = dpi; 319 320 vc4_debugfs_add_regset32(drm, "dpi_regs", &dpi->regset); 321 322 return 0; 323 324 err_destroy_encoder: 325 drm_encoder_cleanup(dpi->encoder); 326 clk_disable_unprepare(dpi->core_clock); 327 return ret; 328 } 329 330 static void vc4_dpi_unbind(struct device *dev, struct device *master, 331 void *data) 332 { 333 struct drm_device *drm = dev_get_drvdata(master); 334 struct vc4_dev *vc4 = to_vc4_dev(drm); 335 struct vc4_dpi *dpi = dev_get_drvdata(dev); 336 337 drm_of_panel_bridge_remove(dev->of_node, 0, 0); 338 339 drm_encoder_cleanup(dpi->encoder); 340 341 clk_disable_unprepare(dpi->core_clock); 342 343 vc4->dpi = NULL; 344 } 345 346 static const struct component_ops vc4_dpi_ops = { 347 .bind = vc4_dpi_bind, 348 .unbind = vc4_dpi_unbind, 349 }; 350 351 static int vc4_dpi_dev_probe(struct platform_device *pdev) 352 { 353 return component_add(&pdev->dev, &vc4_dpi_ops); 354 } 355 356 static int vc4_dpi_dev_remove(struct platform_device *pdev) 357 { 358 component_del(&pdev->dev, &vc4_dpi_ops); 359 return 0; 360 } 361 362 struct platform_driver vc4_dpi_driver = { 363 .probe = vc4_dpi_dev_probe, 364 .remove = vc4_dpi_dev_remove, 365 .driver = { 366 .name = "vc4_dpi", 367 .of_match_table = vc4_dpi_dt_match, 368 }, 369 }; 370