1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * DRM driver for Solomon SSD130x OLED displays 4 * 5 * Copyright 2022 Red Hat Inc. 6 * Author: Javier Martinez Canillas <javierm@redhat.com> 7 * 8 * Based on drivers/video/fbdev/ssd1307fb.c 9 * Copyright 2012 Free Electrons 10 */ 11 12 #include <linux/backlight.h> 13 #include <linux/bitfield.h> 14 #include <linux/bits.h> 15 #include <linux/delay.h> 16 #include <linux/gpio/consumer.h> 17 #include <linux/property.h> 18 #include <linux/pwm.h> 19 #include <linux/regulator/consumer.h> 20 21 #include <drm/drm_atomic_helper.h> 22 #include <drm/drm_damage_helper.h> 23 #include <drm/drm_edid.h> 24 #include <drm/drm_fb_cma_helper.h> 25 #include <drm/drm_fb_helper.h> 26 #include <drm/drm_format_helper.h> 27 #include <drm/drm_framebuffer.h> 28 #include <drm/drm_gem_atomic_helper.h> 29 #include <drm/drm_gem_framebuffer_helper.h> 30 #include <drm/drm_gem_shmem_helper.h> 31 #include <drm/drm_managed.h> 32 #include <drm/drm_modes.h> 33 #include <drm/drm_rect.h> 34 #include <drm/drm_probe_helper.h> 35 36 #include "ssd130x.h" 37 38 #define DRIVER_NAME "ssd130x" 39 #define DRIVER_DESC "DRM driver for Solomon SSD130x OLED displays" 40 #define DRIVER_DATE "20220131" 41 #define DRIVER_MAJOR 1 42 #define DRIVER_MINOR 0 43 44 #define SSD130X_PAGE_COL_START_LOW 0x00 45 #define SSD130X_PAGE_COL_START_HIGH 0x10 46 #define SSD130X_SET_ADDRESS_MODE 0x20 47 #define SSD130X_SET_COL_RANGE 0x21 48 #define SSD130X_SET_PAGE_RANGE 0x22 49 #define SSD130X_CONTRAST 0x81 50 #define SSD130X_SET_LOOKUP_TABLE 0x91 51 #define SSD130X_CHARGE_PUMP 0x8d 52 #define SSD130X_SET_SEG_REMAP 0xa0 53 #define SSD130X_DISPLAY_OFF 0xae 54 #define SSD130X_SET_MULTIPLEX_RATIO 0xa8 55 #define SSD130X_DISPLAY_ON 0xaf 56 #define SSD130X_START_PAGE_ADDRESS 0xb0 57 #define SSD130X_SET_COM_SCAN_DIR 0xc0 58 #define SSD130X_SET_DISPLAY_OFFSET 0xd3 59 #define SSD130X_SET_CLOCK_FREQ 0xd5 60 #define SSD130X_SET_AREA_COLOR_MODE 0xd8 61 #define SSD130X_SET_PRECHARGE_PERIOD 0xd9 62 #define SSD130X_SET_COM_PINS_CONFIG 0xda 63 #define SSD130X_SET_VCOMH 0xdb 64 65 #define SSD130X_PAGE_COL_START_MASK GENMASK(3, 0) 66 #define SSD130X_PAGE_COL_START_HIGH_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val) >> 4) 67 #define SSD130X_PAGE_COL_START_LOW_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val)) 68 #define SSD130X_START_PAGE_ADDRESS_MASK GENMASK(2, 0) 69 #define SSD130X_START_PAGE_ADDRESS_SET(val) FIELD_PREP(SSD130X_START_PAGE_ADDRESS_MASK, (val)) 70 #define SSD130X_SET_SEG_REMAP_MASK GENMASK(0, 0) 71 #define SSD130X_SET_SEG_REMAP_SET(val) FIELD_PREP(SSD130X_SET_SEG_REMAP_MASK, (val)) 72 #define SSD130X_SET_COM_SCAN_DIR_MASK GENMASK(3, 3) 73 #define SSD130X_SET_COM_SCAN_DIR_SET(val) FIELD_PREP(SSD130X_SET_COM_SCAN_DIR_MASK, (val)) 74 #define SSD130X_SET_CLOCK_DIV_MASK GENMASK(3, 0) 75 #define SSD130X_SET_CLOCK_DIV_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_DIV_MASK, (val)) 76 #define SSD130X_SET_CLOCK_FREQ_MASK GENMASK(7, 4) 77 #define SSD130X_SET_CLOCK_FREQ_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_FREQ_MASK, (val)) 78 #define SSD130X_SET_PRECHARGE_PERIOD1_MASK GENMASK(3, 0) 79 #define SSD130X_SET_PRECHARGE_PERIOD1_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD1_MASK, (val)) 80 #define SSD130X_SET_PRECHARGE_PERIOD2_MASK GENMASK(7, 4) 81 #define SSD130X_SET_PRECHARGE_PERIOD2_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD2_MASK, (val)) 82 #define SSD130X_SET_COM_PINS_CONFIG1_MASK GENMASK(4, 4) 83 #define SSD130X_SET_COM_PINS_CONFIG1_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG1_MASK, !(val)) 84 #define SSD130X_SET_COM_PINS_CONFIG2_MASK GENMASK(5, 5) 85 #define SSD130X_SET_COM_PINS_CONFIG2_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG2_MASK, (val)) 86 87 #define SSD130X_SET_ADDRESS_MODE_HORIZONTAL 0x00 88 #define SSD130X_SET_ADDRESS_MODE_VERTICAL 0x01 89 #define SSD130X_SET_ADDRESS_MODE_PAGE 0x02 90 91 #define SSD130X_SET_AREA_COLOR_MODE_ENABLE 0x1e 92 #define SSD130X_SET_AREA_COLOR_MODE_LOW_POWER 0x05 93 94 #define MAX_CONTRAST 255 95 96 const struct ssd130x_deviceinfo ssd130x_variants[] = { 97 [SH1106_ID] = { 98 .default_vcomh = 0x40, 99 .default_dclk_div = 1, 100 .default_dclk_frq = 5, 101 .page_mode_only = 1, 102 }, 103 [SSD1305_ID] = { 104 .default_vcomh = 0x34, 105 .default_dclk_div = 1, 106 .default_dclk_frq = 7, 107 }, 108 [SSD1306_ID] = { 109 .default_vcomh = 0x20, 110 .default_dclk_div = 1, 111 .default_dclk_frq = 8, 112 .need_chargepump = 1, 113 }, 114 [SSD1307_ID] = { 115 .default_vcomh = 0x20, 116 .default_dclk_div = 2, 117 .default_dclk_frq = 12, 118 .need_pwm = 1, 119 }, 120 [SSD1309_ID] = { 121 .default_vcomh = 0x34, 122 .default_dclk_div = 1, 123 .default_dclk_frq = 10, 124 } 125 }; 126 EXPORT_SYMBOL_NS_GPL(ssd130x_variants, DRM_SSD130X); 127 128 static inline struct ssd130x_device *drm_to_ssd130x(struct drm_device *drm) 129 { 130 return container_of(drm, struct ssd130x_device, drm); 131 } 132 133 /* 134 * Helper to write data (SSD130X_DATA) to the device. 135 */ 136 static int ssd130x_write_data(struct ssd130x_device *ssd130x, u8 *values, int count) 137 { 138 return regmap_bulk_write(ssd130x->regmap, SSD130X_DATA, values, count); 139 } 140 141 /* 142 * Helper to write command (SSD130X_COMMAND). The fist variadic argument 143 * is the command to write and the following are the command options. 144 * 145 * Note that the ssd130x protocol requires each command and option to be 146 * written as a SSD130X_COMMAND device register value. That is why a call 147 * to regmap_write(..., SSD130X_COMMAND, ...) is done for each argument. 148 */ 149 static int ssd130x_write_cmd(struct ssd130x_device *ssd130x, int count, 150 /* u8 cmd, u8 option, ... */...) 151 { 152 va_list ap; 153 u8 value; 154 int ret; 155 156 va_start(ap, count); 157 158 do { 159 value = va_arg(ap, int); 160 ret = regmap_write(ssd130x->regmap, SSD130X_COMMAND, value); 161 if (ret) 162 goto out_end; 163 } while (--count); 164 165 out_end: 166 va_end(ap); 167 168 return ret; 169 } 170 171 /* Set address range for horizontal/vertical addressing modes */ 172 static int ssd130x_set_col_range(struct ssd130x_device *ssd130x, 173 u8 col_start, u8 cols) 174 { 175 u8 col_end = col_start + cols - 1; 176 int ret; 177 178 if (col_start == ssd130x->col_start && col_end == ssd130x->col_end) 179 return 0; 180 181 ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_COL_RANGE, col_start, col_end); 182 if (ret < 0) 183 return ret; 184 185 ssd130x->col_start = col_start; 186 ssd130x->col_end = col_end; 187 return 0; 188 } 189 190 static int ssd130x_set_page_range(struct ssd130x_device *ssd130x, 191 u8 page_start, u8 pages) 192 { 193 u8 page_end = page_start + pages - 1; 194 int ret; 195 196 if (page_start == ssd130x->page_start && page_end == ssd130x->page_end) 197 return 0; 198 199 ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_PAGE_RANGE, page_start, page_end); 200 if (ret < 0) 201 return ret; 202 203 ssd130x->page_start = page_start; 204 ssd130x->page_end = page_end; 205 return 0; 206 } 207 208 /* Set page and column start address for page addressing mode */ 209 static int ssd130x_set_page_pos(struct ssd130x_device *ssd130x, 210 u8 page_start, u8 col_start) 211 { 212 int ret; 213 u32 page, col_low, col_high; 214 215 page = SSD130X_START_PAGE_ADDRESS | 216 SSD130X_START_PAGE_ADDRESS_SET(page_start); 217 col_low = SSD130X_PAGE_COL_START_LOW | 218 SSD130X_PAGE_COL_START_LOW_SET(col_start); 219 col_high = SSD130X_PAGE_COL_START_HIGH | 220 SSD130X_PAGE_COL_START_HIGH_SET(col_start); 221 ret = ssd130x_write_cmd(ssd130x, 3, page, col_low, col_high); 222 if (ret < 0) 223 return ret; 224 225 return 0; 226 } 227 228 static int ssd130x_pwm_enable(struct ssd130x_device *ssd130x) 229 { 230 struct device *dev = ssd130x->dev; 231 struct pwm_state pwmstate; 232 233 ssd130x->pwm = pwm_get(dev, NULL); 234 if (IS_ERR(ssd130x->pwm)) { 235 dev_err(dev, "Could not get PWM from firmware description!\n"); 236 return PTR_ERR(ssd130x->pwm); 237 } 238 239 pwm_init_state(ssd130x->pwm, &pwmstate); 240 pwm_set_relative_duty_cycle(&pwmstate, 50, 100); 241 pwm_apply_state(ssd130x->pwm, &pwmstate); 242 243 /* Enable the PWM */ 244 pwm_enable(ssd130x->pwm); 245 246 dev_dbg(dev, "Using PWM%d with a %lluns period.\n", 247 ssd130x->pwm->pwm, pwm_get_period(ssd130x->pwm)); 248 249 return 0; 250 } 251 252 static void ssd130x_reset(struct ssd130x_device *ssd130x) 253 { 254 if (!ssd130x->reset) 255 return; 256 257 /* Reset the screen */ 258 gpiod_set_value_cansleep(ssd130x->reset, 1); 259 udelay(4); 260 gpiod_set_value_cansleep(ssd130x->reset, 0); 261 udelay(4); 262 } 263 264 static int ssd130x_power_on(struct ssd130x_device *ssd130x) 265 { 266 struct device *dev = ssd130x->dev; 267 int ret; 268 269 ssd130x_reset(ssd130x); 270 271 ret = regulator_enable(ssd130x->vcc_reg); 272 if (ret) { 273 dev_err(dev, "Failed to enable VCC: %d\n", ret); 274 return ret; 275 } 276 277 if (ssd130x->device_info->need_pwm) { 278 ret = ssd130x_pwm_enable(ssd130x); 279 if (ret) { 280 dev_err(dev, "Failed to enable PWM: %d\n", ret); 281 regulator_disable(ssd130x->vcc_reg); 282 return ret; 283 } 284 } 285 286 return 0; 287 } 288 289 static void ssd130x_power_off(struct ssd130x_device *ssd130x) 290 { 291 pwm_disable(ssd130x->pwm); 292 pwm_put(ssd130x->pwm); 293 294 regulator_disable(ssd130x->vcc_reg); 295 } 296 297 static int ssd130x_init(struct ssd130x_device *ssd130x) 298 { 299 u32 precharge, dclk, com_invdir, compins, chargepump, seg_remap; 300 int ret; 301 302 /* Set initial contrast */ 303 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_CONTRAST, ssd130x->contrast); 304 if (ret < 0) 305 return ret; 306 307 /* Set segment re-map */ 308 seg_remap = (SSD130X_SET_SEG_REMAP | 309 SSD130X_SET_SEG_REMAP_SET(ssd130x->seg_remap)); 310 ret = ssd130x_write_cmd(ssd130x, 1, seg_remap); 311 if (ret < 0) 312 return ret; 313 314 /* Set COM direction */ 315 com_invdir = (SSD130X_SET_COM_SCAN_DIR | 316 SSD130X_SET_COM_SCAN_DIR_SET(ssd130x->com_invdir)); 317 ret = ssd130x_write_cmd(ssd130x, 1, com_invdir); 318 if (ret < 0) 319 return ret; 320 321 /* Set multiplex ratio value */ 322 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_MULTIPLEX_RATIO, ssd130x->height - 1); 323 if (ret < 0) 324 return ret; 325 326 /* set display offset value */ 327 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_DISPLAY_OFFSET, ssd130x->com_offset); 328 if (ret < 0) 329 return ret; 330 331 /* Set clock frequency */ 332 dclk = (SSD130X_SET_CLOCK_DIV_SET(ssd130x->dclk_div - 1) | 333 SSD130X_SET_CLOCK_FREQ_SET(ssd130x->dclk_frq)); 334 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_CLOCK_FREQ, dclk); 335 if (ret < 0) 336 return ret; 337 338 /* Set Area Color Mode ON/OFF & Low Power Display Mode */ 339 if (ssd130x->area_color_enable || ssd130x->low_power) { 340 u32 mode = 0; 341 342 if (ssd130x->area_color_enable) 343 mode |= SSD130X_SET_AREA_COLOR_MODE_ENABLE; 344 345 if (ssd130x->low_power) 346 mode |= SSD130X_SET_AREA_COLOR_MODE_LOW_POWER; 347 348 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_AREA_COLOR_MODE, mode); 349 if (ret < 0) 350 return ret; 351 } 352 353 /* Set precharge period in number of ticks from the internal clock */ 354 precharge = (SSD130X_SET_PRECHARGE_PERIOD1_SET(ssd130x->prechargep1) | 355 SSD130X_SET_PRECHARGE_PERIOD2_SET(ssd130x->prechargep2)); 356 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_PRECHARGE_PERIOD, precharge); 357 if (ret < 0) 358 return ret; 359 360 /* Set COM pins configuration */ 361 compins = BIT(1); 362 compins |= (SSD130X_SET_COM_PINS_CONFIG1_SET(ssd130x->com_seq) | 363 SSD130X_SET_COM_PINS_CONFIG2_SET(ssd130x->com_lrremap)); 364 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_COM_PINS_CONFIG, compins); 365 if (ret < 0) 366 return ret; 367 368 /* Set VCOMH */ 369 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_VCOMH, ssd130x->vcomh); 370 if (ret < 0) 371 return ret; 372 373 /* Turn on the DC-DC Charge Pump */ 374 chargepump = BIT(4); 375 376 if (ssd130x->device_info->need_chargepump) 377 chargepump |= BIT(2); 378 379 ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_CHARGE_PUMP, chargepump); 380 if (ret < 0) 381 return ret; 382 383 /* Set lookup table */ 384 if (ssd130x->lookup_table_set) { 385 int i; 386 387 ret = ssd130x_write_cmd(ssd130x, 1, SSD130X_SET_LOOKUP_TABLE); 388 if (ret < 0) 389 return ret; 390 391 for (i = 0; i < ARRAY_SIZE(ssd130x->lookup_table); i++) { 392 u8 val = ssd130x->lookup_table[i]; 393 394 if (val < 31 || val > 63) 395 dev_warn(ssd130x->dev, 396 "lookup table index %d value out of range 31 <= %d <= 63\n", 397 i, val); 398 ret = ssd130x_write_cmd(ssd130x, 1, val); 399 if (ret < 0) 400 return ret; 401 } 402 } 403 404 /* Switch to page addressing mode */ 405 if (ssd130x->page_address_mode) 406 return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, 407 SSD130X_SET_ADDRESS_MODE_PAGE); 408 409 /* Switch to horizontal addressing mode */ 410 return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, 411 SSD130X_SET_ADDRESS_MODE_HORIZONTAL); 412 } 413 414 static int ssd130x_update_rect(struct ssd130x_device *ssd130x, u8 *buf, 415 struct drm_rect *rect) 416 { 417 unsigned int x = rect->x1; 418 unsigned int y = rect->y1; 419 unsigned int width = drm_rect_width(rect); 420 unsigned int height = drm_rect_height(rect); 421 unsigned int line_length = DIV_ROUND_UP(width, 8); 422 unsigned int pages = DIV_ROUND_UP(height, 8); 423 struct drm_device *drm = &ssd130x->drm; 424 u32 array_idx = 0; 425 int ret, i, j, k; 426 u8 *data_array = NULL; 427 428 drm_WARN_ONCE(drm, y % 8 != 0, "y must be aligned to screen page\n"); 429 430 data_array = kcalloc(width, pages, GFP_KERNEL); 431 if (!data_array) 432 return -ENOMEM; 433 434 /* 435 * The screen is divided in pages, each having a height of 8 436 * pixels, and the width of the screen. When sending a byte of 437 * data to the controller, it gives the 8 bits for the current 438 * column. I.e, the first byte are the 8 bits of the first 439 * column, then the 8 bits for the second column, etc. 440 * 441 * 442 * Representation of the screen, assuming it is 5 bits 443 * wide. Each letter-number combination is a bit that controls 444 * one pixel. 445 * 446 * A0 A1 A2 A3 A4 447 * B0 B1 B2 B3 B4 448 * C0 C1 C2 C3 C4 449 * D0 D1 D2 D3 D4 450 * E0 E1 E2 E3 E4 451 * F0 F1 F2 F3 F4 452 * G0 G1 G2 G3 G4 453 * H0 H1 H2 H3 H4 454 * 455 * If you want to update this screen, you need to send 5 bytes: 456 * (1) A0 B0 C0 D0 E0 F0 G0 H0 457 * (2) A1 B1 C1 D1 E1 F1 G1 H1 458 * (3) A2 B2 C2 D2 E2 F2 G2 H2 459 * (4) A3 B3 C3 D3 E3 F3 G3 H3 460 * (5) A4 B4 C4 D4 E4 F4 G4 H4 461 */ 462 463 if (!ssd130x->page_address_mode) { 464 /* Set address range for horizontal addressing mode */ 465 ret = ssd130x_set_col_range(ssd130x, ssd130x->col_offset + x, width); 466 if (ret < 0) 467 goto out_free; 468 469 ret = ssd130x_set_page_range(ssd130x, ssd130x->page_offset + y / 8, pages); 470 if (ret < 0) 471 goto out_free; 472 } 473 474 for (i = 0; i < pages; i++) { 475 int m = 8; 476 477 /* Last page may be partial */ 478 if (8 * (y / 8 + i + 1) > ssd130x->height) 479 m = ssd130x->height % 8; 480 for (j = 0; j < width; j++) { 481 u8 data = 0; 482 483 for (k = 0; k < m; k++) { 484 u8 byte = buf[(8 * i + k) * line_length + j / 8]; 485 u8 bit = (byte >> (j % 8)) & 1; 486 487 data |= bit << k; 488 } 489 data_array[array_idx++] = data; 490 } 491 492 /* 493 * In page addressing mode, the start address needs to be reset, 494 * and each page then needs to be written out separately. 495 */ 496 if (ssd130x->page_address_mode) { 497 ret = ssd130x_set_page_pos(ssd130x, 498 ssd130x->page_offset + i, 499 ssd130x->col_offset + x); 500 if (ret < 0) 501 goto out_free; 502 503 ret = ssd130x_write_data(ssd130x, data_array, width); 504 if (ret < 0) 505 goto out_free; 506 507 array_idx = 0; 508 } 509 } 510 511 /* Write out update in one go if we aren't using page addressing mode */ 512 if (!ssd130x->page_address_mode) 513 ret = ssd130x_write_data(ssd130x, data_array, width * pages); 514 515 out_free: 516 kfree(data_array); 517 return ret; 518 } 519 520 static void ssd130x_clear_screen(struct ssd130x_device *ssd130x) 521 { 522 u8 *buf = NULL; 523 struct drm_rect fullscreen = { 524 .x1 = 0, 525 .x2 = ssd130x->width, 526 .y1 = 0, 527 .y2 = ssd130x->height, 528 }; 529 530 buf = kcalloc(DIV_ROUND_UP(ssd130x->width, 8), ssd130x->height, 531 GFP_KERNEL); 532 if (!buf) 533 return; 534 535 ssd130x_update_rect(ssd130x, buf, &fullscreen); 536 537 kfree(buf); 538 } 539 540 static int ssd130x_fb_blit_rect(struct drm_framebuffer *fb, const struct iosys_map *map, 541 struct drm_rect *rect) 542 { 543 struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); 544 void *vmap = map->vaddr; /* TODO: Use mapping abstraction properly */ 545 unsigned int dst_pitch; 546 int ret = 0; 547 u8 *buf = NULL; 548 549 /* Align y to display page boundaries */ 550 rect->y1 = round_down(rect->y1, 8); 551 rect->y2 = min_t(unsigned int, round_up(rect->y2, 8), ssd130x->height); 552 553 dst_pitch = DIV_ROUND_UP(drm_rect_width(rect), 8); 554 buf = kcalloc(dst_pitch, drm_rect_height(rect), GFP_KERNEL); 555 if (!buf) 556 return -ENOMEM; 557 558 drm_fb_xrgb8888_to_mono(buf, dst_pitch, vmap, fb, rect); 559 560 ssd130x_update_rect(ssd130x, buf, rect); 561 562 kfree(buf); 563 564 return ret; 565 } 566 567 static int ssd130x_display_pipe_mode_valid(struct drm_simple_display_pipe *pipe, 568 const struct drm_display_mode *mode) 569 { 570 struct ssd130x_device *ssd130x = drm_to_ssd130x(pipe->crtc.dev); 571 572 if (mode->hdisplay != ssd130x->mode.hdisplay && 573 mode->vdisplay != ssd130x->mode.vdisplay) 574 return MODE_ONE_SIZE; 575 576 if (mode->hdisplay != ssd130x->mode.hdisplay) 577 return MODE_ONE_WIDTH; 578 579 if (mode->vdisplay != ssd130x->mode.vdisplay) 580 return MODE_ONE_HEIGHT; 581 582 return MODE_OK; 583 } 584 585 static void ssd130x_display_pipe_enable(struct drm_simple_display_pipe *pipe, 586 struct drm_crtc_state *crtc_state, 587 struct drm_plane_state *plane_state) 588 { 589 struct ssd130x_device *ssd130x = drm_to_ssd130x(pipe->crtc.dev); 590 struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); 591 struct drm_device *drm = &ssd130x->drm; 592 int idx, ret; 593 594 ret = ssd130x_power_on(ssd130x); 595 if (ret) 596 return; 597 598 ret = ssd130x_init(ssd130x); 599 if (ret) 600 goto out_power_off; 601 602 if (!drm_dev_enter(drm, &idx)) 603 goto out_power_off; 604 605 ssd130x_fb_blit_rect(plane_state->fb, &shadow_plane_state->data[0], &plane_state->dst); 606 607 ssd130x_write_cmd(ssd130x, 1, SSD130X_DISPLAY_ON); 608 609 backlight_enable(ssd130x->bl_dev); 610 611 drm_dev_exit(idx); 612 613 return; 614 out_power_off: 615 ssd130x_power_off(ssd130x); 616 } 617 618 static void ssd130x_display_pipe_disable(struct drm_simple_display_pipe *pipe) 619 { 620 struct ssd130x_device *ssd130x = drm_to_ssd130x(pipe->crtc.dev); 621 struct drm_device *drm = &ssd130x->drm; 622 int idx; 623 624 if (!drm_dev_enter(drm, &idx)) 625 return; 626 627 ssd130x_clear_screen(ssd130x); 628 629 backlight_disable(ssd130x->bl_dev); 630 631 ssd130x_write_cmd(ssd130x, 1, SSD130X_DISPLAY_OFF); 632 633 ssd130x_power_off(ssd130x); 634 635 drm_dev_exit(idx); 636 } 637 638 static void ssd130x_display_pipe_update(struct drm_simple_display_pipe *pipe, 639 struct drm_plane_state *old_plane_state) 640 { 641 struct ssd130x_device *ssd130x = drm_to_ssd130x(pipe->crtc.dev); 642 struct drm_plane_state *plane_state = pipe->plane.state; 643 struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); 644 struct drm_framebuffer *fb = plane_state->fb; 645 struct drm_device *drm = &ssd130x->drm; 646 struct drm_rect src_clip, dst_clip; 647 int idx; 648 649 if (!fb) 650 return; 651 652 if (!pipe->crtc.state->active) 653 return; 654 655 if (!drm_atomic_helper_damage_merged(old_plane_state, plane_state, &src_clip)) 656 return; 657 658 dst_clip = plane_state->dst; 659 if (!drm_rect_intersect(&dst_clip, &src_clip)) 660 return; 661 662 if (!drm_dev_enter(drm, &idx)) 663 return; 664 665 ssd130x_fb_blit_rect(plane_state->fb, &shadow_plane_state->data[0], &dst_clip); 666 667 drm_dev_exit(idx); 668 } 669 670 static const struct drm_simple_display_pipe_funcs ssd130x_pipe_funcs = { 671 .mode_valid = ssd130x_display_pipe_mode_valid, 672 .enable = ssd130x_display_pipe_enable, 673 .disable = ssd130x_display_pipe_disable, 674 .update = ssd130x_display_pipe_update, 675 DRM_GEM_SIMPLE_DISPLAY_PIPE_SHADOW_PLANE_FUNCS, 676 }; 677 678 static int ssd130x_connector_get_modes(struct drm_connector *connector) 679 { 680 struct ssd130x_device *ssd130x = drm_to_ssd130x(connector->dev); 681 struct drm_display_mode *mode; 682 struct device *dev = ssd130x->dev; 683 684 mode = drm_mode_duplicate(connector->dev, &ssd130x->mode); 685 if (!mode) { 686 dev_err(dev, "Failed to duplicated mode\n"); 687 return 0; 688 } 689 690 drm_mode_probed_add(connector, mode); 691 drm_set_preferred_mode(connector, mode->hdisplay, mode->vdisplay); 692 693 /* There is only a single mode */ 694 return 1; 695 } 696 697 static const struct drm_connector_helper_funcs ssd130x_connector_helper_funcs = { 698 .get_modes = ssd130x_connector_get_modes, 699 }; 700 701 static const struct drm_connector_funcs ssd130x_connector_funcs = { 702 .reset = drm_atomic_helper_connector_reset, 703 .fill_modes = drm_helper_probe_single_connector_modes, 704 .destroy = drm_connector_cleanup, 705 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 706 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 707 }; 708 709 static const struct drm_mode_config_funcs ssd130x_mode_config_funcs = { 710 .fb_create = drm_gem_fb_create_with_dirty, 711 .atomic_check = drm_atomic_helper_check, 712 .atomic_commit = drm_atomic_helper_commit, 713 }; 714 715 static const uint32_t ssd130x_formats[] = { 716 DRM_FORMAT_XRGB8888, 717 }; 718 719 DEFINE_DRM_GEM_FOPS(ssd130x_fops); 720 721 static const struct drm_driver ssd130x_drm_driver = { 722 DRM_GEM_SHMEM_DRIVER_OPS, 723 .name = DRIVER_NAME, 724 .desc = DRIVER_DESC, 725 .date = DRIVER_DATE, 726 .major = DRIVER_MAJOR, 727 .minor = DRIVER_MINOR, 728 .driver_features = DRIVER_ATOMIC | DRIVER_GEM | DRIVER_MODESET, 729 .fops = &ssd130x_fops, 730 }; 731 732 static int ssd130x_update_bl(struct backlight_device *bdev) 733 { 734 struct ssd130x_device *ssd130x = bl_get_data(bdev); 735 int brightness = backlight_get_brightness(bdev); 736 int ret; 737 738 ssd130x->contrast = brightness; 739 740 ret = ssd130x_write_cmd(ssd130x, 1, SSD130X_CONTRAST); 741 if (ret < 0) 742 return ret; 743 744 ret = ssd130x_write_cmd(ssd130x, 1, ssd130x->contrast); 745 if (ret < 0) 746 return ret; 747 748 return 0; 749 } 750 751 static const struct backlight_ops ssd130xfb_bl_ops = { 752 .update_status = ssd130x_update_bl, 753 }; 754 755 static void ssd130x_parse_properties(struct ssd130x_device *ssd130x) 756 { 757 struct device *dev = ssd130x->dev; 758 759 if (device_property_read_u32(dev, "solomon,width", &ssd130x->width)) 760 ssd130x->width = 96; 761 762 if (device_property_read_u32(dev, "solomon,height", &ssd130x->height)) 763 ssd130x->height = 16; 764 765 if (device_property_read_u32(dev, "solomon,page-offset", &ssd130x->page_offset)) 766 ssd130x->page_offset = 1; 767 768 if (device_property_read_u32(dev, "solomon,col-offset", &ssd130x->col_offset)) 769 ssd130x->col_offset = 0; 770 771 if (device_property_read_u32(dev, "solomon,com-offset", &ssd130x->com_offset)) 772 ssd130x->com_offset = 0; 773 774 if (device_property_read_u32(dev, "solomon,prechargep1", &ssd130x->prechargep1)) 775 ssd130x->prechargep1 = 2; 776 777 if (device_property_read_u32(dev, "solomon,prechargep2", &ssd130x->prechargep2)) 778 ssd130x->prechargep2 = 2; 779 780 if (!device_property_read_u8_array(dev, "solomon,lookup-table", 781 ssd130x->lookup_table, 782 ARRAY_SIZE(ssd130x->lookup_table))) 783 ssd130x->lookup_table_set = 1; 784 785 ssd130x->seg_remap = !device_property_read_bool(dev, "solomon,segment-no-remap"); 786 ssd130x->com_seq = device_property_read_bool(dev, "solomon,com-seq"); 787 ssd130x->com_lrremap = device_property_read_bool(dev, "solomon,com-lrremap"); 788 ssd130x->com_invdir = device_property_read_bool(dev, "solomon,com-invdir"); 789 ssd130x->area_color_enable = 790 device_property_read_bool(dev, "solomon,area-color-enable"); 791 ssd130x->low_power = device_property_read_bool(dev, "solomon,low-power"); 792 793 ssd130x->contrast = 127; 794 ssd130x->vcomh = ssd130x->device_info->default_vcomh; 795 796 /* Setup display timing */ 797 if (device_property_read_u32(dev, "solomon,dclk-div", &ssd130x->dclk_div)) 798 ssd130x->dclk_div = ssd130x->device_info->default_dclk_div; 799 if (device_property_read_u32(dev, "solomon,dclk-frq", &ssd130x->dclk_frq)) 800 ssd130x->dclk_frq = ssd130x->device_info->default_dclk_frq; 801 } 802 803 static int ssd130x_init_modeset(struct ssd130x_device *ssd130x) 804 { 805 struct drm_display_mode *mode = &ssd130x->mode; 806 struct device *dev = ssd130x->dev; 807 struct drm_device *drm = &ssd130x->drm; 808 unsigned long max_width, max_height; 809 int ret; 810 811 ret = drmm_mode_config_init(drm); 812 if (ret) { 813 dev_err(dev, "DRM mode config init failed: %d\n", ret); 814 return ret; 815 } 816 817 mode->type = DRM_MODE_TYPE_DRIVER; 818 mode->clock = 1; 819 mode->hdisplay = mode->htotal = ssd130x->width; 820 mode->hsync_start = mode->hsync_end = ssd130x->width; 821 mode->vdisplay = mode->vtotal = ssd130x->height; 822 mode->vsync_start = mode->vsync_end = ssd130x->height; 823 mode->width_mm = 27; 824 mode->height_mm = 27; 825 826 max_width = max_t(unsigned long, mode->hdisplay, DRM_SHADOW_PLANE_MAX_WIDTH); 827 max_height = max_t(unsigned long, mode->vdisplay, DRM_SHADOW_PLANE_MAX_HEIGHT); 828 829 drm->mode_config.min_width = mode->hdisplay; 830 drm->mode_config.max_width = max_width; 831 drm->mode_config.min_height = mode->vdisplay; 832 drm->mode_config.max_height = max_height; 833 drm->mode_config.preferred_depth = 32; 834 drm->mode_config.funcs = &ssd130x_mode_config_funcs; 835 836 ret = drm_connector_init(drm, &ssd130x->connector, &ssd130x_connector_funcs, 837 DRM_MODE_CONNECTOR_Unknown); 838 if (ret) { 839 dev_err(dev, "DRM connector init failed: %d\n", ret); 840 return ret; 841 } 842 843 drm_connector_helper_add(&ssd130x->connector, &ssd130x_connector_helper_funcs); 844 845 ret = drm_simple_display_pipe_init(drm, &ssd130x->pipe, &ssd130x_pipe_funcs, 846 ssd130x_formats, ARRAY_SIZE(ssd130x_formats), 847 NULL, &ssd130x->connector); 848 if (ret) { 849 dev_err(dev, "DRM simple display pipeline init failed: %d\n", ret); 850 return ret; 851 } 852 853 drm_plane_enable_fb_damage_clips(&ssd130x->pipe.plane); 854 855 drm_mode_config_reset(drm); 856 857 return 0; 858 } 859 860 static int ssd130x_get_resources(struct ssd130x_device *ssd130x) 861 { 862 struct device *dev = ssd130x->dev; 863 864 ssd130x->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 865 if (IS_ERR(ssd130x->reset)) 866 return dev_err_probe(dev, PTR_ERR(ssd130x->reset), 867 "Failed to get reset gpio\n"); 868 869 ssd130x->vcc_reg = devm_regulator_get(dev, "vcc"); 870 if (IS_ERR(ssd130x->vcc_reg)) 871 return dev_err_probe(dev, PTR_ERR(ssd130x->vcc_reg), 872 "Failed to get VCC regulator\n"); 873 874 return 0; 875 } 876 877 struct ssd130x_device *ssd130x_probe(struct device *dev, struct regmap *regmap) 878 { 879 struct ssd130x_device *ssd130x; 880 struct backlight_device *bl; 881 struct drm_device *drm; 882 int ret; 883 884 ssd130x = devm_drm_dev_alloc(dev, &ssd130x_drm_driver, 885 struct ssd130x_device, drm); 886 if (IS_ERR(ssd130x)) 887 return ERR_PTR(dev_err_probe(dev, PTR_ERR(ssd130x), 888 "Failed to allocate DRM device\n")); 889 890 drm = &ssd130x->drm; 891 892 ssd130x->dev = dev; 893 ssd130x->regmap = regmap; 894 ssd130x->device_info = device_get_match_data(dev); 895 896 if (ssd130x->device_info->page_mode_only) 897 ssd130x->page_address_mode = 1; 898 899 ssd130x_parse_properties(ssd130x); 900 901 ret = ssd130x_get_resources(ssd130x); 902 if (ret) 903 return ERR_PTR(ret); 904 905 bl = devm_backlight_device_register(dev, dev_name(dev), dev, ssd130x, 906 &ssd130xfb_bl_ops, NULL); 907 if (IS_ERR(bl)) 908 return ERR_PTR(dev_err_probe(dev, PTR_ERR(bl), 909 "Unable to register backlight device\n")); 910 911 bl->props.brightness = ssd130x->contrast; 912 bl->props.max_brightness = MAX_CONTRAST; 913 ssd130x->bl_dev = bl; 914 915 ret = ssd130x_init_modeset(ssd130x); 916 if (ret) 917 return ERR_PTR(ret); 918 919 ret = drm_dev_register(drm, 0); 920 if (ret) 921 return ERR_PTR(dev_err_probe(dev, ret, "DRM device register failed\n")); 922 923 drm_fbdev_generic_setup(drm, 0); 924 925 return ssd130x; 926 } 927 EXPORT_SYMBOL_GPL(ssd130x_probe); 928 929 void ssd130x_remove(struct ssd130x_device *ssd130x) 930 { 931 drm_dev_unplug(&ssd130x->drm); 932 } 933 EXPORT_SYMBOL_GPL(ssd130x_remove); 934 935 void ssd130x_shutdown(struct ssd130x_device *ssd130x) 936 { 937 drm_atomic_helper_shutdown(&ssd130x->drm); 938 } 939 EXPORT_SYMBOL_GPL(ssd130x_shutdown); 940 941 MODULE_DESCRIPTION(DRIVER_DESC); 942 MODULE_AUTHOR("Javier Martinez Canillas <javierm@redhat.com>"); 943 MODULE_LICENSE("GPL v2"); 944