1# SPDX-License-Identifier: GPL-2.0-only 2config DRM_OMAP 3 tristate "OMAP DRM" 4 depends on DRM && OF 5 depends on ARCH_OMAP2PLUS 6 select DRM_KMS_HELPER 7 select VIDEOMODE_HELPERS 8 select HDMI 9 default n 10 help 11 DRM display driver for OMAP2/3/4 based boards. 12 13if DRM_OMAP 14 15config OMAP2_DSS_DEBUG 16 bool "Debug support" 17 default n 18 help 19 This enables printing of debug messages. Alternatively, debug messages 20 can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting 21 appropriate flags in <debugfs>/dynamic_debug/control. 22 23config OMAP2_DSS_DEBUGFS 24 bool "Debugfs filesystem support" 25 depends on DEBUG_FS 26 default n 27 help 28 This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables 29 querying about clock configuration and register configuration of dss, 30 dispc, dsi, hdmi and rfbi. 31 32config OMAP2_DSS_COLLECT_IRQ_STATS 33 bool "Collect DSS IRQ statistics" 34 depends on OMAP2_DSS_DEBUGFS 35 default n 36 help 37 Collect DSS IRQ statistics, printable via debugfs. 38 39 The statistics can be found from 40 <debugfs>/omapdss/dispc_irq for DISPC interrupts, and 41 <debugfs>/omapdss/dsi_irq for DSI interrupts. 42 43config OMAP2_DSS_DPI 44 bool "DPI support" 45 default y 46 help 47 DPI Interface. This is the Parallel Display Interface. 48 49config OMAP2_DSS_VENC 50 bool "VENC support" 51 default y 52 help 53 OMAP Video Encoder support for S-Video and composite TV-out. 54 55config OMAP2_DSS_HDMI_COMMON 56 bool 57 58config OMAP4_DSS_HDMI 59 bool "HDMI support for OMAP4" 60 default y 61 select OMAP2_DSS_HDMI_COMMON 62 help 63 HDMI support for OMAP4 based SoCs. 64 65config OMAP4_DSS_HDMI_CEC 66 bool "Enable HDMI CEC support for OMAP4" 67 depends on OMAP4_DSS_HDMI 68 select CEC_CORE 69 default y 70 help 71 When selected the HDMI transmitter will support the CEC feature. 72 73config OMAP5_DSS_HDMI 74 bool "HDMI support for OMAP5" 75 default n 76 select OMAP2_DSS_HDMI_COMMON 77 help 78 HDMI Interface for OMAP5 and similar cores. This adds the High 79 Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI 80 specification. 81 82config OMAP2_DSS_SDI 83 bool "SDI support" 84 default n 85 help 86 SDI (Serial Display Interface) support. 87 88 SDI is a high speed one-way display serial bus between the host 89 processor and a display. 90 91config OMAP2_DSS_DSI 92 bool "DSI support" 93 default n 94 select DRM_MIPI_DSI 95 help 96 MIPI DSI (Display Serial Interface) support. 97 98 DSI is a high speed half-duplex serial interface between the host 99 processor and a peripheral, such as a display or a framebuffer chip. 100 101 See http://www.mipi.org/ for DSI specifications. 102 103config OMAP2_DSS_MIN_FCK_PER_PCK 104 int "Minimum FCK/PCK ratio (for scaling)" 105 range 0 32 106 default 0 107 help 108 This can be used to adjust the minimum FCK/PCK ratio. 109 110 With this you can make sure that DISPC FCK is at least 111 n x PCK. Video plane scaling requires higher FCK than 112 normally. 113 114 If this is set to 0, there's no extra constraint on the 115 DISPC FCK. However, the FCK will at minimum be 116 2xPCK (if active matrix) or 3xPCK (if passive matrix). 117 118 Max FCK is 173MHz, so this doesn't work if your PCK 119 is very high. 120 121config OMAP2_DSS_SLEEP_AFTER_VENC_RESET 122 bool "Sleep 20ms after VENC reset" 123 default y 124 help 125 There is a 20ms sleep after VENC reset which seemed to fix the 126 reset. The reason for the bug is unclear, and it's also unclear 127 on what platforms this happens. 128 129 This option enables the sleep, and is enabled by default. You can 130 disable the sleep if it doesn't cause problems on your platform. 131 132endif 133