1 /* 2 * Copyright © 2013 Intel Corporation 3 * 4 * Permission is hereby granted, free of charge, to any person obtaining a 5 * copy of this software and associated documentation files (the "Software"), 6 * to deal in the Software without restriction, including without limitation 7 * the rights to use, copy, modify, merge, publish, distribute, sublicense, 8 * and/or sell copies of the Software, and to permit persons to whom the 9 * Software is furnished to do so, subject to the following conditions: 10 * 11 * The above copyright notice and this permission notice (including the next 12 * paragraph) shall be included in all copies or substantial portions of the 13 * Software. 14 * 15 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR 16 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, 17 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL 18 * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER 19 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 20 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER 21 * DEALINGS IN THE SOFTWARE. 22 * 23 * Author: Jani Nikula <jani.nikula@intel.com> 24 */ 25 26 #include <linux/slab.h> 27 28 #include <drm/drm_atomic_helper.h> 29 #include <drm/drm_crtc.h> 30 #include <drm/drm_edid.h> 31 #include <drm/drm_mipi_dsi.h> 32 33 #include "i915_drv.h" 34 #include "intel_atomic.h" 35 #include "intel_backlight.h" 36 #include "intel_connector.h" 37 #include "intel_crtc.h" 38 #include "intel_de.h" 39 #include "intel_display_types.h" 40 #include "intel_dsi.h" 41 #include "intel_dsi_vbt.h" 42 #include "intel_fifo_underrun.h" 43 #include "intel_panel.h" 44 #include "skl_scaler.h" 45 #include "vlv_dsi.h" 46 #include "vlv_dsi_pll.h" 47 #include "vlv_dsi_regs.h" 48 #include "vlv_sideband.h" 49 50 /* return pixels in terms of txbyteclkhs */ 51 static u16 txbyteclkhs(u16 pixels, int bpp, int lane_count, 52 u16 burst_mode_ratio) 53 { 54 return DIV_ROUND_UP(DIV_ROUND_UP(pixels * bpp * burst_mode_ratio, 55 8 * 100), lane_count); 56 } 57 58 /* return pixels equvalent to txbyteclkhs */ 59 static u16 pixels_from_txbyteclkhs(u16 clk_hs, int bpp, int lane_count, 60 u16 burst_mode_ratio) 61 { 62 return DIV_ROUND_UP((clk_hs * lane_count * 8 * 100), 63 (bpp * burst_mode_ratio)); 64 } 65 66 enum mipi_dsi_pixel_format pixel_format_from_register_bits(u32 fmt) 67 { 68 /* It just so happens the VBT matches register contents. */ 69 switch (fmt) { 70 case VID_MODE_FORMAT_RGB888: 71 return MIPI_DSI_FMT_RGB888; 72 case VID_MODE_FORMAT_RGB666: 73 return MIPI_DSI_FMT_RGB666; 74 case VID_MODE_FORMAT_RGB666_PACKED: 75 return MIPI_DSI_FMT_RGB666_PACKED; 76 case VID_MODE_FORMAT_RGB565: 77 return MIPI_DSI_FMT_RGB565; 78 default: 79 MISSING_CASE(fmt); 80 return MIPI_DSI_FMT_RGB666; 81 } 82 } 83 84 void vlv_dsi_wait_for_fifo_empty(struct intel_dsi *intel_dsi, enum port port) 85 { 86 struct drm_encoder *encoder = &intel_dsi->base.base; 87 struct drm_device *dev = encoder->dev; 88 struct drm_i915_private *dev_priv = to_i915(dev); 89 u32 mask; 90 91 mask = LP_CTRL_FIFO_EMPTY | HS_CTRL_FIFO_EMPTY | 92 LP_DATA_FIFO_EMPTY | HS_DATA_FIFO_EMPTY; 93 94 if (intel_de_wait_for_set(dev_priv, MIPI_GEN_FIFO_STAT(port), 95 mask, 100)) 96 drm_err(&dev_priv->drm, "DPI FIFOs are not empty\n"); 97 } 98 99 static void write_data(struct drm_i915_private *dev_priv, 100 i915_reg_t reg, 101 const u8 *data, u32 len) 102 { 103 u32 i, j; 104 105 for (i = 0; i < len; i += 4) { 106 u32 val = 0; 107 108 for (j = 0; j < min_t(u32, len - i, 4); j++) 109 val |= *data++ << 8 * j; 110 111 intel_de_write(dev_priv, reg, val); 112 } 113 } 114 115 static void read_data(struct drm_i915_private *dev_priv, 116 i915_reg_t reg, 117 u8 *data, u32 len) 118 { 119 u32 i, j; 120 121 for (i = 0; i < len; i += 4) { 122 u32 val = intel_de_read(dev_priv, reg); 123 124 for (j = 0; j < min_t(u32, len - i, 4); j++) 125 *data++ = val >> 8 * j; 126 } 127 } 128 129 static ssize_t intel_dsi_host_transfer(struct mipi_dsi_host *host, 130 const struct mipi_dsi_msg *msg) 131 { 132 struct intel_dsi_host *intel_dsi_host = to_intel_dsi_host(host); 133 struct drm_device *dev = intel_dsi_host->intel_dsi->base.base.dev; 134 struct drm_i915_private *dev_priv = to_i915(dev); 135 enum port port = intel_dsi_host->port; 136 struct mipi_dsi_packet packet; 137 ssize_t ret; 138 const u8 *header, *data; 139 i915_reg_t data_reg, ctrl_reg; 140 u32 data_mask, ctrl_mask; 141 142 ret = mipi_dsi_create_packet(&packet, msg); 143 if (ret < 0) 144 return ret; 145 146 header = packet.header; 147 data = packet.payload; 148 149 if (msg->flags & MIPI_DSI_MSG_USE_LPM) { 150 data_reg = MIPI_LP_GEN_DATA(port); 151 data_mask = LP_DATA_FIFO_FULL; 152 ctrl_reg = MIPI_LP_GEN_CTRL(port); 153 ctrl_mask = LP_CTRL_FIFO_FULL; 154 } else { 155 data_reg = MIPI_HS_GEN_DATA(port); 156 data_mask = HS_DATA_FIFO_FULL; 157 ctrl_reg = MIPI_HS_GEN_CTRL(port); 158 ctrl_mask = HS_CTRL_FIFO_FULL; 159 } 160 161 /* note: this is never true for reads */ 162 if (packet.payload_length) { 163 if (intel_de_wait_for_clear(dev_priv, MIPI_GEN_FIFO_STAT(port), 164 data_mask, 50)) 165 drm_err(&dev_priv->drm, 166 "Timeout waiting for HS/LP DATA FIFO !full\n"); 167 168 write_data(dev_priv, data_reg, packet.payload, 169 packet.payload_length); 170 } 171 172 if (msg->rx_len) { 173 intel_de_write(dev_priv, MIPI_INTR_STAT(port), 174 GEN_READ_DATA_AVAIL); 175 } 176 177 if (intel_de_wait_for_clear(dev_priv, MIPI_GEN_FIFO_STAT(port), 178 ctrl_mask, 50)) { 179 drm_err(&dev_priv->drm, 180 "Timeout waiting for HS/LP CTRL FIFO !full\n"); 181 } 182 183 intel_de_write(dev_priv, ctrl_reg, 184 header[2] << 16 | header[1] << 8 | header[0]); 185 186 /* ->rx_len is set only for reads */ 187 if (msg->rx_len) { 188 data_mask = GEN_READ_DATA_AVAIL; 189 if (intel_de_wait_for_set(dev_priv, MIPI_INTR_STAT(port), 190 data_mask, 50)) 191 drm_err(&dev_priv->drm, 192 "Timeout waiting for read data.\n"); 193 194 read_data(dev_priv, data_reg, msg->rx_buf, msg->rx_len); 195 } 196 197 /* XXX: fix for reads and writes */ 198 return 4 + packet.payload_length; 199 } 200 201 static int intel_dsi_host_attach(struct mipi_dsi_host *host, 202 struct mipi_dsi_device *dsi) 203 { 204 return 0; 205 } 206 207 static int intel_dsi_host_detach(struct mipi_dsi_host *host, 208 struct mipi_dsi_device *dsi) 209 { 210 return 0; 211 } 212 213 static const struct mipi_dsi_host_ops intel_dsi_host_ops = { 214 .attach = intel_dsi_host_attach, 215 .detach = intel_dsi_host_detach, 216 .transfer = intel_dsi_host_transfer, 217 }; 218 219 /* 220 * send a video mode command 221 * 222 * XXX: commands with data in MIPI_DPI_DATA? 223 */ 224 static int dpi_send_cmd(struct intel_dsi *intel_dsi, u32 cmd, bool hs, 225 enum port port) 226 { 227 struct drm_encoder *encoder = &intel_dsi->base.base; 228 struct drm_device *dev = encoder->dev; 229 struct drm_i915_private *dev_priv = to_i915(dev); 230 u32 mask; 231 232 /* XXX: pipe, hs */ 233 if (hs) 234 cmd &= ~DPI_LP_MODE; 235 else 236 cmd |= DPI_LP_MODE; 237 238 /* clear bit */ 239 intel_de_write(dev_priv, MIPI_INTR_STAT(port), SPL_PKT_SENT_INTERRUPT); 240 241 /* XXX: old code skips write if control unchanged */ 242 if (cmd == intel_de_read(dev_priv, MIPI_DPI_CONTROL(port))) 243 drm_dbg_kms(&dev_priv->drm, 244 "Same special packet %02x twice in a row.\n", cmd); 245 246 intel_de_write(dev_priv, MIPI_DPI_CONTROL(port), cmd); 247 248 mask = SPL_PKT_SENT_INTERRUPT; 249 if (intel_de_wait_for_set(dev_priv, MIPI_INTR_STAT(port), mask, 100)) 250 drm_err(&dev_priv->drm, 251 "Video mode command 0x%08x send failed.\n", cmd); 252 253 return 0; 254 } 255 256 static void band_gap_reset(struct drm_i915_private *dev_priv) 257 { 258 vlv_flisdsi_get(dev_priv); 259 260 vlv_flisdsi_write(dev_priv, 0x08, 0x0001); 261 vlv_flisdsi_write(dev_priv, 0x0F, 0x0005); 262 vlv_flisdsi_write(dev_priv, 0x0F, 0x0025); 263 udelay(150); 264 vlv_flisdsi_write(dev_priv, 0x0F, 0x0000); 265 vlv_flisdsi_write(dev_priv, 0x08, 0x0000); 266 267 vlv_flisdsi_put(dev_priv); 268 } 269 270 static int intel_dsi_compute_config(struct intel_encoder *encoder, 271 struct intel_crtc_state *pipe_config, 272 struct drm_connector_state *conn_state) 273 { 274 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 275 struct intel_dsi *intel_dsi = container_of(encoder, struct intel_dsi, 276 base); 277 struct intel_connector *intel_connector = intel_dsi->attached_connector; 278 struct drm_display_mode *adjusted_mode = &pipe_config->hw.adjusted_mode; 279 int ret; 280 281 drm_dbg_kms(&dev_priv->drm, "\n"); 282 pipe_config->output_format = INTEL_OUTPUT_FORMAT_RGB; 283 284 ret = intel_panel_compute_config(intel_connector, adjusted_mode); 285 if (ret) 286 return ret; 287 288 ret = intel_panel_fitting(pipe_config, conn_state); 289 if (ret) 290 return ret; 291 292 if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN) 293 return -EINVAL; 294 295 /* DSI uses short packets for sync events, so clear mode flags for DSI */ 296 adjusted_mode->flags = 0; 297 298 if (intel_dsi->pixel_format == MIPI_DSI_FMT_RGB888) 299 pipe_config->pipe_bpp = 24; 300 else 301 pipe_config->pipe_bpp = 18; 302 303 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 304 /* Enable Frame time stamp based scanline reporting */ 305 pipe_config->mode_flags |= 306 I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP; 307 308 /* Dual link goes to DSI transcoder A. */ 309 if (intel_dsi->ports == BIT(PORT_C)) 310 pipe_config->cpu_transcoder = TRANSCODER_DSI_C; 311 else 312 pipe_config->cpu_transcoder = TRANSCODER_DSI_A; 313 314 ret = bxt_dsi_pll_compute(encoder, pipe_config); 315 if (ret) 316 return -EINVAL; 317 } else { 318 ret = vlv_dsi_pll_compute(encoder, pipe_config); 319 if (ret) 320 return -EINVAL; 321 } 322 323 pipe_config->clock_set = true; 324 325 return 0; 326 } 327 328 static bool glk_dsi_enable_io(struct intel_encoder *encoder) 329 { 330 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 331 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 332 enum port port; 333 u32 tmp; 334 bool cold_boot = false; 335 336 /* Set the MIPI mode 337 * If MIPI_Mode is off, then writing to LP_Wake bit is not reflecting. 338 * Power ON MIPI IO first and then write into IO reset and LP wake bits 339 */ 340 for_each_dsi_port(port, intel_dsi->ports) { 341 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 342 intel_de_write(dev_priv, MIPI_CTRL(port), 343 tmp | GLK_MIPIIO_ENABLE); 344 } 345 346 /* Put the IO into reset */ 347 tmp = intel_de_read(dev_priv, MIPI_CTRL(PORT_A)); 348 tmp &= ~GLK_MIPIIO_RESET_RELEASED; 349 intel_de_write(dev_priv, MIPI_CTRL(PORT_A), tmp); 350 351 /* Program LP Wake */ 352 for_each_dsi_port(port, intel_dsi->ports) { 353 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 354 if (!(intel_de_read(dev_priv, MIPI_DEVICE_READY(port)) & DEVICE_READY)) 355 tmp &= ~GLK_LP_WAKE; 356 else 357 tmp |= GLK_LP_WAKE; 358 intel_de_write(dev_priv, MIPI_CTRL(port), tmp); 359 } 360 361 /* Wait for Pwr ACK */ 362 for_each_dsi_port(port, intel_dsi->ports) { 363 if (intel_de_wait_for_set(dev_priv, MIPI_CTRL(port), 364 GLK_MIPIIO_PORT_POWERED, 20)) 365 drm_err(&dev_priv->drm, "MIPIO port is powergated\n"); 366 } 367 368 /* Check for cold boot scenario */ 369 for_each_dsi_port(port, intel_dsi->ports) { 370 cold_boot |= 371 !(intel_de_read(dev_priv, MIPI_DEVICE_READY(port)) & DEVICE_READY); 372 } 373 374 return cold_boot; 375 } 376 377 static void glk_dsi_device_ready(struct intel_encoder *encoder) 378 { 379 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 380 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 381 enum port port; 382 u32 val; 383 384 /* Wait for MIPI PHY status bit to set */ 385 for_each_dsi_port(port, intel_dsi->ports) { 386 if (intel_de_wait_for_set(dev_priv, MIPI_CTRL(port), 387 GLK_PHY_STATUS_PORT_READY, 20)) 388 drm_err(&dev_priv->drm, "PHY is not ON\n"); 389 } 390 391 /* Get IO out of reset */ 392 val = intel_de_read(dev_priv, MIPI_CTRL(PORT_A)); 393 intel_de_write(dev_priv, MIPI_CTRL(PORT_A), 394 val | GLK_MIPIIO_RESET_RELEASED); 395 396 /* Get IO out of Low power state*/ 397 for_each_dsi_port(port, intel_dsi->ports) { 398 if (!(intel_de_read(dev_priv, MIPI_DEVICE_READY(port)) & DEVICE_READY)) { 399 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 400 val &= ~ULPS_STATE_MASK; 401 val |= DEVICE_READY; 402 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 403 usleep_range(10, 15); 404 } else { 405 /* Enter ULPS */ 406 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 407 val &= ~ULPS_STATE_MASK; 408 val |= (ULPS_STATE_ENTER | DEVICE_READY); 409 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 410 411 /* Wait for ULPS active */ 412 if (intel_de_wait_for_clear(dev_priv, MIPI_CTRL(port), 413 GLK_ULPS_NOT_ACTIVE, 20)) 414 drm_err(&dev_priv->drm, "ULPS not active\n"); 415 416 /* Exit ULPS */ 417 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 418 val &= ~ULPS_STATE_MASK; 419 val |= (ULPS_STATE_EXIT | DEVICE_READY); 420 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 421 422 /* Enter Normal Mode */ 423 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 424 val &= ~ULPS_STATE_MASK; 425 val |= (ULPS_STATE_NORMAL_OPERATION | DEVICE_READY); 426 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 427 428 val = intel_de_read(dev_priv, MIPI_CTRL(port)); 429 val &= ~GLK_LP_WAKE; 430 intel_de_write(dev_priv, MIPI_CTRL(port), val); 431 } 432 } 433 434 /* Wait for Stop state */ 435 for_each_dsi_port(port, intel_dsi->ports) { 436 if (intel_de_wait_for_set(dev_priv, MIPI_CTRL(port), 437 GLK_DATA_LANE_STOP_STATE, 20)) 438 drm_err(&dev_priv->drm, 439 "Date lane not in STOP state\n"); 440 } 441 442 /* Wait for AFE LATCH */ 443 for_each_dsi_port(port, intel_dsi->ports) { 444 if (intel_de_wait_for_set(dev_priv, BXT_MIPI_PORT_CTRL(port), 445 AFE_LATCHOUT, 20)) 446 drm_err(&dev_priv->drm, 447 "D-PHY not entering LP-11 state\n"); 448 } 449 } 450 451 static void bxt_dsi_device_ready(struct intel_encoder *encoder) 452 { 453 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 454 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 455 enum port port; 456 u32 val; 457 458 drm_dbg_kms(&dev_priv->drm, "\n"); 459 460 /* Enable MIPI PHY transparent latch */ 461 for_each_dsi_port(port, intel_dsi->ports) { 462 val = intel_de_read(dev_priv, BXT_MIPI_PORT_CTRL(port)); 463 intel_de_write(dev_priv, BXT_MIPI_PORT_CTRL(port), 464 val | LP_OUTPUT_HOLD); 465 usleep_range(2000, 2500); 466 } 467 468 /* Clear ULPS and set device ready */ 469 for_each_dsi_port(port, intel_dsi->ports) { 470 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 471 val &= ~ULPS_STATE_MASK; 472 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 473 usleep_range(2000, 2500); 474 val |= DEVICE_READY; 475 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 476 } 477 } 478 479 static void vlv_dsi_device_ready(struct intel_encoder *encoder) 480 { 481 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 482 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 483 enum port port; 484 u32 val; 485 486 drm_dbg_kms(&dev_priv->drm, "\n"); 487 488 vlv_flisdsi_get(dev_priv); 489 /* program rcomp for compliance, reduce from 50 ohms to 45 ohms 490 * needed everytime after power gate */ 491 vlv_flisdsi_write(dev_priv, 0x04, 0x0004); 492 vlv_flisdsi_put(dev_priv); 493 494 /* bandgap reset is needed after everytime we do power gate */ 495 band_gap_reset(dev_priv); 496 497 for_each_dsi_port(port, intel_dsi->ports) { 498 499 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 500 ULPS_STATE_ENTER); 501 usleep_range(2500, 3000); 502 503 /* Enable MIPI PHY transparent latch 504 * Common bit for both MIPI Port A & MIPI Port C 505 * No similar bit in MIPI Port C reg 506 */ 507 val = intel_de_read(dev_priv, MIPI_PORT_CTRL(PORT_A)); 508 intel_de_write(dev_priv, MIPI_PORT_CTRL(PORT_A), 509 val | LP_OUTPUT_HOLD); 510 usleep_range(1000, 1500); 511 512 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 513 ULPS_STATE_EXIT); 514 usleep_range(2500, 3000); 515 516 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 517 DEVICE_READY); 518 usleep_range(2500, 3000); 519 } 520 } 521 522 static void intel_dsi_device_ready(struct intel_encoder *encoder) 523 { 524 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 525 526 if (IS_GEMINILAKE(dev_priv)) 527 glk_dsi_device_ready(encoder); 528 else if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) 529 bxt_dsi_device_ready(encoder); 530 else 531 vlv_dsi_device_ready(encoder); 532 } 533 534 static void glk_dsi_enter_low_power_mode(struct intel_encoder *encoder) 535 { 536 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 537 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 538 enum port port; 539 u32 val; 540 541 /* Enter ULPS */ 542 for_each_dsi_port(port, intel_dsi->ports) { 543 val = intel_de_read(dev_priv, MIPI_DEVICE_READY(port)); 544 val &= ~ULPS_STATE_MASK; 545 val |= (ULPS_STATE_ENTER | DEVICE_READY); 546 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), val); 547 } 548 549 /* Wait for MIPI PHY status bit to unset */ 550 for_each_dsi_port(port, intel_dsi->ports) { 551 if (intel_de_wait_for_clear(dev_priv, MIPI_CTRL(port), 552 GLK_PHY_STATUS_PORT_READY, 20)) 553 drm_err(&dev_priv->drm, "PHY is not turning OFF\n"); 554 } 555 556 /* Wait for Pwr ACK bit to unset */ 557 for_each_dsi_port(port, intel_dsi->ports) { 558 if (intel_de_wait_for_clear(dev_priv, MIPI_CTRL(port), 559 GLK_MIPIIO_PORT_POWERED, 20)) 560 drm_err(&dev_priv->drm, 561 "MIPI IO Port is not powergated\n"); 562 } 563 } 564 565 static void glk_dsi_disable_mipi_io(struct intel_encoder *encoder) 566 { 567 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 568 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 569 enum port port; 570 u32 tmp; 571 572 /* Put the IO into reset */ 573 tmp = intel_de_read(dev_priv, MIPI_CTRL(PORT_A)); 574 tmp &= ~GLK_MIPIIO_RESET_RELEASED; 575 intel_de_write(dev_priv, MIPI_CTRL(PORT_A), tmp); 576 577 /* Wait for MIPI PHY status bit to unset */ 578 for_each_dsi_port(port, intel_dsi->ports) { 579 if (intel_de_wait_for_clear(dev_priv, MIPI_CTRL(port), 580 GLK_PHY_STATUS_PORT_READY, 20)) 581 drm_err(&dev_priv->drm, "PHY is not turning OFF\n"); 582 } 583 584 /* Clear MIPI mode */ 585 for_each_dsi_port(port, intel_dsi->ports) { 586 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 587 tmp &= ~GLK_MIPIIO_ENABLE; 588 intel_de_write(dev_priv, MIPI_CTRL(port), tmp); 589 } 590 } 591 592 static void glk_dsi_clear_device_ready(struct intel_encoder *encoder) 593 { 594 glk_dsi_enter_low_power_mode(encoder); 595 glk_dsi_disable_mipi_io(encoder); 596 } 597 598 static void vlv_dsi_clear_device_ready(struct intel_encoder *encoder) 599 { 600 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 601 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 602 enum port port; 603 604 drm_dbg_kms(&dev_priv->drm, "\n"); 605 for_each_dsi_port(port, intel_dsi->ports) { 606 /* Common bit for both MIPI Port A & MIPI Port C on VLV/CHV */ 607 i915_reg_t port_ctrl = IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv) ? 608 BXT_MIPI_PORT_CTRL(port) : MIPI_PORT_CTRL(PORT_A); 609 u32 val; 610 611 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 612 DEVICE_READY | ULPS_STATE_ENTER); 613 usleep_range(2000, 2500); 614 615 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 616 DEVICE_READY | ULPS_STATE_EXIT); 617 usleep_range(2000, 2500); 618 619 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 620 DEVICE_READY | ULPS_STATE_ENTER); 621 usleep_range(2000, 2500); 622 623 /* 624 * On VLV/CHV, wait till Clock lanes are in LP-00 state for MIPI 625 * Port A only. MIPI Port C has no similar bit for checking. 626 */ 627 if ((IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv) || port == PORT_A) && 628 intel_de_wait_for_clear(dev_priv, port_ctrl, 629 AFE_LATCHOUT, 30)) 630 drm_err(&dev_priv->drm, "DSI LP not going Low\n"); 631 632 /* Disable MIPI PHY transparent latch */ 633 val = intel_de_read(dev_priv, port_ctrl); 634 intel_de_write(dev_priv, port_ctrl, val & ~LP_OUTPUT_HOLD); 635 usleep_range(1000, 1500); 636 637 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 0x00); 638 usleep_range(2000, 2500); 639 } 640 } 641 642 static void intel_dsi_port_enable(struct intel_encoder *encoder, 643 const struct intel_crtc_state *crtc_state) 644 { 645 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 646 struct intel_crtc *crtc = to_intel_crtc(crtc_state->uapi.crtc); 647 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 648 enum port port; 649 650 if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK) { 651 u32 temp; 652 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 653 for_each_dsi_port(port, intel_dsi->ports) { 654 temp = intel_de_read(dev_priv, 655 MIPI_CTRL(port)); 656 temp &= ~BXT_PIXEL_OVERLAP_CNT_MASK | 657 intel_dsi->pixel_overlap << 658 BXT_PIXEL_OVERLAP_CNT_SHIFT; 659 intel_de_write(dev_priv, MIPI_CTRL(port), 660 temp); 661 } 662 } else { 663 temp = intel_de_read(dev_priv, VLV_CHICKEN_3); 664 temp &= ~PIXEL_OVERLAP_CNT_MASK | 665 intel_dsi->pixel_overlap << 666 PIXEL_OVERLAP_CNT_SHIFT; 667 intel_de_write(dev_priv, VLV_CHICKEN_3, temp); 668 } 669 } 670 671 for_each_dsi_port(port, intel_dsi->ports) { 672 i915_reg_t port_ctrl = IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv) ? 673 BXT_MIPI_PORT_CTRL(port) : MIPI_PORT_CTRL(port); 674 u32 temp; 675 676 temp = intel_de_read(dev_priv, port_ctrl); 677 678 temp &= ~LANE_CONFIGURATION_MASK; 679 temp &= ~DUAL_LINK_MODE_MASK; 680 681 if (intel_dsi->ports == (BIT(PORT_A) | BIT(PORT_C))) { 682 temp |= (intel_dsi->dual_link - 1) 683 << DUAL_LINK_MODE_SHIFT; 684 if (IS_BROXTON(dev_priv)) 685 temp |= LANE_CONFIGURATION_DUAL_LINK_A; 686 else 687 temp |= crtc->pipe ? 688 LANE_CONFIGURATION_DUAL_LINK_B : 689 LANE_CONFIGURATION_DUAL_LINK_A; 690 } 691 692 if (intel_dsi->pixel_format != MIPI_DSI_FMT_RGB888) 693 temp |= DITHERING_ENABLE; 694 695 /* assert ip_tg_enable signal */ 696 intel_de_write(dev_priv, port_ctrl, temp | DPI_ENABLE); 697 intel_de_posting_read(dev_priv, port_ctrl); 698 } 699 } 700 701 static void intel_dsi_port_disable(struct intel_encoder *encoder) 702 { 703 struct drm_device *dev = encoder->base.dev; 704 struct drm_i915_private *dev_priv = to_i915(dev); 705 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 706 enum port port; 707 708 for_each_dsi_port(port, intel_dsi->ports) { 709 i915_reg_t port_ctrl = IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv) ? 710 BXT_MIPI_PORT_CTRL(port) : MIPI_PORT_CTRL(port); 711 u32 temp; 712 713 /* de-assert ip_tg_enable signal */ 714 temp = intel_de_read(dev_priv, port_ctrl); 715 intel_de_write(dev_priv, port_ctrl, temp & ~DPI_ENABLE); 716 intel_de_posting_read(dev_priv, port_ctrl); 717 } 718 } 719 720 static void intel_dsi_wait_panel_power_cycle(struct intel_dsi *intel_dsi) 721 { 722 ktime_t panel_power_on_time; 723 s64 panel_power_off_duration; 724 725 panel_power_on_time = ktime_get_boottime(); 726 panel_power_off_duration = ktime_ms_delta(panel_power_on_time, 727 intel_dsi->panel_power_off_time); 728 729 if (panel_power_off_duration < (s64)intel_dsi->panel_pwr_cycle_delay) 730 msleep(intel_dsi->panel_pwr_cycle_delay - panel_power_off_duration); 731 } 732 733 static void intel_dsi_prepare(struct intel_encoder *intel_encoder, 734 const struct intel_crtc_state *pipe_config); 735 static void intel_dsi_unprepare(struct intel_encoder *encoder); 736 737 /* 738 * Panel enable/disable sequences from the VBT spec. 739 * 740 * Note the spec has AssertReset / DeassertReset swapped from their 741 * usual naming. We use the normal names to avoid confusion (so below 742 * they are swapped compared to the spec). 743 * 744 * Steps starting with MIPI refer to VBT sequences, note that for v2 745 * VBTs several steps which have a VBT in v2 are expected to be handled 746 * directly by the driver, by directly driving gpios for example. 747 * 748 * v2 video mode seq v3 video mode seq command mode seq 749 * - power on - MIPIPanelPowerOn - power on 750 * - wait t1+t2 - wait t1+t2 751 * - MIPIDeassertResetPin - MIPIDeassertResetPin - MIPIDeassertResetPin 752 * - io lines to lp-11 - io lines to lp-11 - io lines to lp-11 753 * - MIPISendInitialDcsCmds - MIPISendInitialDcsCmds - MIPISendInitialDcsCmds 754 * - MIPITearOn 755 * - MIPIDisplayOn 756 * - turn on DPI - turn on DPI - set pipe to dsr mode 757 * - MIPIDisplayOn - MIPIDisplayOn 758 * - wait t5 - wait t5 759 * - backlight on - MIPIBacklightOn - backlight on 760 * ... ... ... issue mem cmds ... 761 * - backlight off - MIPIBacklightOff - backlight off 762 * - wait t6 - wait t6 763 * - MIPIDisplayOff 764 * - turn off DPI - turn off DPI - disable pipe dsr mode 765 * - MIPITearOff 766 * - MIPIDisplayOff - MIPIDisplayOff 767 * - io lines to lp-00 - io lines to lp-00 - io lines to lp-00 768 * - MIPIAssertResetPin - MIPIAssertResetPin - MIPIAssertResetPin 769 * - wait t3 - wait t3 770 * - power off - MIPIPanelPowerOff - power off 771 * - wait t4 - wait t4 772 */ 773 774 /* 775 * DSI port enable has to be done before pipe and plane enable, so we do it in 776 * the pre_enable hook instead of the enable hook. 777 */ 778 static void intel_dsi_pre_enable(struct intel_atomic_state *state, 779 struct intel_encoder *encoder, 780 const struct intel_crtc_state *pipe_config, 781 const struct drm_connector_state *conn_state) 782 { 783 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 784 struct intel_crtc *crtc = to_intel_crtc(pipe_config->uapi.crtc); 785 struct intel_connector *connector = to_intel_connector(conn_state->connector); 786 struct drm_i915_private *dev_priv = to_i915(crtc->base.dev); 787 enum pipe pipe = crtc->pipe; 788 enum port port; 789 u32 val; 790 bool glk_cold_boot = false; 791 792 drm_dbg_kms(&dev_priv->drm, "\n"); 793 794 intel_dsi_wait_panel_power_cycle(intel_dsi); 795 796 intel_set_cpu_fifo_underrun_reporting(dev_priv, pipe, true); 797 798 /* 799 * The BIOS may leave the PLL in a wonky state where it doesn't 800 * lock. It needs to be fully powered down to fix it. 801 */ 802 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 803 bxt_dsi_pll_disable(encoder); 804 bxt_dsi_pll_enable(encoder, pipe_config); 805 } else { 806 vlv_dsi_pll_disable(encoder); 807 vlv_dsi_pll_enable(encoder, pipe_config); 808 } 809 810 if (IS_BROXTON(dev_priv)) { 811 /* Add MIPI IO reset programming for modeset */ 812 val = intel_de_read(dev_priv, BXT_P_CR_GT_DISP_PWRON); 813 intel_de_write(dev_priv, BXT_P_CR_GT_DISP_PWRON, 814 val | MIPIO_RST_CTRL); 815 816 /* Power up DSI regulator */ 817 intel_de_write(dev_priv, BXT_P_DSI_REGULATOR_CFG, STAP_SELECT); 818 intel_de_write(dev_priv, BXT_P_DSI_REGULATOR_TX_CTRL, 0); 819 } 820 821 if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) { 822 u32 val; 823 824 /* Disable DPOunit clock gating, can stall pipe */ 825 val = intel_de_read(dev_priv, DSPCLK_GATE_D); 826 val |= DPOUNIT_CLOCK_GATE_DISABLE; 827 intel_de_write(dev_priv, DSPCLK_GATE_D, val); 828 } 829 830 if (!IS_GEMINILAKE(dev_priv)) 831 intel_dsi_prepare(encoder, pipe_config); 832 833 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_POWER_ON); 834 835 /* 836 * Give the panel time to power-on and then deassert its reset. 837 * Depending on the VBT MIPI sequences version the deassert-seq 838 * may contain the necessary delay, intel_dsi_msleep() will skip 839 * the delay in that case. If there is no deassert-seq, then an 840 * unconditional msleep is used to give the panel time to power-on. 841 */ 842 if (connector->panel.vbt.dsi.sequence[MIPI_SEQ_DEASSERT_RESET]) { 843 intel_dsi_msleep(intel_dsi, intel_dsi->panel_on_delay); 844 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_DEASSERT_RESET); 845 } else { 846 msleep(intel_dsi->panel_on_delay); 847 } 848 849 if (IS_GEMINILAKE(dev_priv)) { 850 glk_cold_boot = glk_dsi_enable_io(encoder); 851 852 /* Prepare port in cold boot(s3/s4) scenario */ 853 if (glk_cold_boot) 854 intel_dsi_prepare(encoder, pipe_config); 855 } 856 857 /* Put device in ready state (LP-11) */ 858 intel_dsi_device_ready(encoder); 859 860 /* Prepare port in normal boot scenario */ 861 if (IS_GEMINILAKE(dev_priv) && !glk_cold_boot) 862 intel_dsi_prepare(encoder, pipe_config); 863 864 /* Send initialization commands in LP mode */ 865 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_INIT_OTP); 866 867 /* 868 * Enable port in pre-enable phase itself because as per hw team 869 * recommendation, port should be enabled before plane & pipe 870 */ 871 if (is_cmd_mode(intel_dsi)) { 872 for_each_dsi_port(port, intel_dsi->ports) 873 intel_de_write(dev_priv, 874 MIPI_MAX_RETURN_PKT_SIZE(port), 8 * 4); 875 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_TEAR_ON); 876 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_DISPLAY_ON); 877 } else { 878 msleep(20); /* XXX */ 879 for_each_dsi_port(port, intel_dsi->ports) 880 dpi_send_cmd(intel_dsi, TURN_ON, false, port); 881 intel_dsi_msleep(intel_dsi, 100); 882 883 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_DISPLAY_ON); 884 885 intel_dsi_port_enable(encoder, pipe_config); 886 } 887 888 intel_backlight_enable(pipe_config, conn_state); 889 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_BACKLIGHT_ON); 890 } 891 892 static void bxt_dsi_enable(struct intel_atomic_state *state, 893 struct intel_encoder *encoder, 894 const struct intel_crtc_state *crtc_state, 895 const struct drm_connector_state *conn_state) 896 { 897 drm_WARN_ON(state->base.dev, crtc_state->has_pch_encoder); 898 899 intel_crtc_vblank_on(crtc_state); 900 } 901 902 /* 903 * DSI port disable has to be done after pipe and plane disable, so we do it in 904 * the post_disable hook. 905 */ 906 static void intel_dsi_disable(struct intel_atomic_state *state, 907 struct intel_encoder *encoder, 908 const struct intel_crtc_state *old_crtc_state, 909 const struct drm_connector_state *old_conn_state) 910 { 911 struct drm_i915_private *i915 = to_i915(encoder->base.dev); 912 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 913 enum port port; 914 915 drm_dbg_kms(&i915->drm, "\n"); 916 917 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_BACKLIGHT_OFF); 918 intel_backlight_disable(old_conn_state); 919 920 /* 921 * According to the spec we should send SHUTDOWN before 922 * MIPI_SEQ_DISPLAY_OFF only for v3+ VBTs, but field testing 923 * has shown that the v3 sequence works for v2 VBTs too 924 */ 925 if (is_vid_mode(intel_dsi)) { 926 /* Send Shutdown command to the panel in LP mode */ 927 for_each_dsi_port(port, intel_dsi->ports) 928 dpi_send_cmd(intel_dsi, SHUTDOWN, false, port); 929 msleep(10); 930 } 931 } 932 933 static void intel_dsi_clear_device_ready(struct intel_encoder *encoder) 934 { 935 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 936 937 if (IS_GEMINILAKE(dev_priv)) 938 glk_dsi_clear_device_ready(encoder); 939 else 940 vlv_dsi_clear_device_ready(encoder); 941 } 942 943 static void intel_dsi_post_disable(struct intel_atomic_state *state, 944 struct intel_encoder *encoder, 945 const struct intel_crtc_state *old_crtc_state, 946 const struct drm_connector_state *old_conn_state) 947 { 948 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 949 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 950 enum port port; 951 u32 val; 952 953 drm_dbg_kms(&dev_priv->drm, "\n"); 954 955 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 956 intel_crtc_vblank_off(old_crtc_state); 957 958 skl_scaler_disable(old_crtc_state); 959 } 960 961 if (is_vid_mode(intel_dsi)) { 962 for_each_dsi_port(port, intel_dsi->ports) 963 vlv_dsi_wait_for_fifo_empty(intel_dsi, port); 964 965 intel_dsi_port_disable(encoder); 966 usleep_range(2000, 5000); 967 } 968 969 intel_dsi_unprepare(encoder); 970 971 /* 972 * if disable packets are sent before sending shutdown packet then in 973 * some next enable sequence send turn on packet error is observed 974 */ 975 if (is_cmd_mode(intel_dsi)) 976 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_TEAR_OFF); 977 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_DISPLAY_OFF); 978 979 /* Transition to LP-00 */ 980 intel_dsi_clear_device_ready(encoder); 981 982 if (IS_BROXTON(dev_priv)) { 983 /* Power down DSI regulator to save power */ 984 intel_de_write(dev_priv, BXT_P_DSI_REGULATOR_CFG, STAP_SELECT); 985 intel_de_write(dev_priv, BXT_P_DSI_REGULATOR_TX_CTRL, 986 HS_IO_CTRL_SELECT); 987 988 /* Add MIPI IO reset programming for modeset */ 989 val = intel_de_read(dev_priv, BXT_P_CR_GT_DISP_PWRON); 990 intel_de_write(dev_priv, BXT_P_CR_GT_DISP_PWRON, 991 val & ~MIPIO_RST_CTRL); 992 } 993 994 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 995 bxt_dsi_pll_disable(encoder); 996 } else { 997 u32 val; 998 999 vlv_dsi_pll_disable(encoder); 1000 1001 val = intel_de_read(dev_priv, DSPCLK_GATE_D); 1002 val &= ~DPOUNIT_CLOCK_GATE_DISABLE; 1003 intel_de_write(dev_priv, DSPCLK_GATE_D, val); 1004 } 1005 1006 /* Assert reset */ 1007 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_ASSERT_RESET); 1008 1009 intel_dsi_msleep(intel_dsi, intel_dsi->panel_off_delay); 1010 intel_dsi_vbt_exec_sequence(intel_dsi, MIPI_SEQ_POWER_OFF); 1011 1012 intel_dsi->panel_power_off_time = ktime_get_boottime(); 1013 } 1014 1015 static void intel_dsi_shutdown(struct intel_encoder *encoder) 1016 { 1017 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 1018 1019 intel_dsi_wait_panel_power_cycle(intel_dsi); 1020 } 1021 1022 static bool intel_dsi_get_hw_state(struct intel_encoder *encoder, 1023 enum pipe *pipe) 1024 { 1025 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 1026 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 1027 intel_wakeref_t wakeref; 1028 enum port port; 1029 bool active = false; 1030 1031 drm_dbg_kms(&dev_priv->drm, "\n"); 1032 1033 wakeref = intel_display_power_get_if_enabled(dev_priv, 1034 encoder->power_domain); 1035 if (!wakeref) 1036 return false; 1037 1038 /* 1039 * On Broxton the PLL needs to be enabled with a valid divider 1040 * configuration, otherwise accessing DSI registers will hang the 1041 * machine. See BSpec North Display Engine registers/MIPI[BXT]. 1042 */ 1043 if ((IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) && 1044 !bxt_dsi_pll_is_enabled(dev_priv)) 1045 goto out_put_power; 1046 1047 /* XXX: this only works for one DSI output */ 1048 for_each_dsi_port(port, intel_dsi->ports) { 1049 i915_reg_t ctrl_reg = IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv) ? 1050 BXT_MIPI_PORT_CTRL(port) : MIPI_PORT_CTRL(port); 1051 bool enabled = intel_de_read(dev_priv, ctrl_reg) & DPI_ENABLE; 1052 1053 /* 1054 * Due to some hardware limitations on VLV/CHV, the DPI enable 1055 * bit in port C control register does not get set. As a 1056 * workaround, check pipe B conf instead. 1057 */ 1058 if ((IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) && 1059 port == PORT_C) 1060 enabled = intel_de_read(dev_priv, PIPECONF(PIPE_B)) & PIPECONF_ENABLE; 1061 1062 /* Try command mode if video mode not enabled */ 1063 if (!enabled) { 1064 u32 tmp = intel_de_read(dev_priv, 1065 MIPI_DSI_FUNC_PRG(port)); 1066 enabled = tmp & CMD_MODE_DATA_WIDTH_MASK; 1067 } 1068 1069 if (!enabled) 1070 continue; 1071 1072 if (!(intel_de_read(dev_priv, MIPI_DEVICE_READY(port)) & DEVICE_READY)) 1073 continue; 1074 1075 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 1076 u32 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 1077 tmp &= BXT_PIPE_SELECT_MASK; 1078 tmp >>= BXT_PIPE_SELECT_SHIFT; 1079 1080 if (drm_WARN_ON(&dev_priv->drm, tmp > PIPE_C)) 1081 continue; 1082 1083 *pipe = tmp; 1084 } else { 1085 *pipe = port == PORT_A ? PIPE_A : PIPE_B; 1086 } 1087 1088 active = true; 1089 break; 1090 } 1091 1092 out_put_power: 1093 intel_display_power_put(dev_priv, encoder->power_domain, wakeref); 1094 1095 return active; 1096 } 1097 1098 static void bxt_dsi_get_pipe_config(struct intel_encoder *encoder, 1099 struct intel_crtc_state *pipe_config) 1100 { 1101 struct drm_device *dev = encoder->base.dev; 1102 struct drm_i915_private *dev_priv = to_i915(dev); 1103 struct drm_display_mode *adjusted_mode = 1104 &pipe_config->hw.adjusted_mode; 1105 struct drm_display_mode *adjusted_mode_sw; 1106 struct intel_crtc *crtc = to_intel_crtc(pipe_config->uapi.crtc); 1107 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 1108 unsigned int lane_count = intel_dsi->lane_count; 1109 unsigned int bpp, fmt; 1110 enum port port; 1111 u16 hactive, hfp, hsync, hbp, vfp, vsync, vbp; 1112 u16 hfp_sw, hsync_sw, hbp_sw; 1113 u16 crtc_htotal_sw, crtc_hsync_start_sw, crtc_hsync_end_sw, 1114 crtc_hblank_start_sw, crtc_hblank_end_sw; 1115 1116 /* FIXME: hw readout should not depend on SW state */ 1117 adjusted_mode_sw = &crtc->config->hw.adjusted_mode; 1118 1119 /* 1120 * Atleast one port is active as encoder->get_config called only if 1121 * encoder->get_hw_state() returns true. 1122 */ 1123 for_each_dsi_port(port, intel_dsi->ports) { 1124 if (intel_de_read(dev_priv, BXT_MIPI_PORT_CTRL(port)) & DPI_ENABLE) 1125 break; 1126 } 1127 1128 fmt = intel_de_read(dev_priv, MIPI_DSI_FUNC_PRG(port)) & VID_MODE_FORMAT_MASK; 1129 bpp = mipi_dsi_pixel_format_to_bpp( 1130 pixel_format_from_register_bits(fmt)); 1131 1132 pipe_config->pipe_bpp = bdw_get_pipemisc_bpp(crtc); 1133 1134 /* Enable Frame time stamo based scanline reporting */ 1135 pipe_config->mode_flags |= 1136 I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP; 1137 1138 /* In terms of pixels */ 1139 adjusted_mode->crtc_hdisplay = 1140 intel_de_read(dev_priv, 1141 BXT_MIPI_TRANS_HACTIVE(port)); 1142 adjusted_mode->crtc_vdisplay = 1143 intel_de_read(dev_priv, 1144 BXT_MIPI_TRANS_VACTIVE(port)); 1145 adjusted_mode->crtc_vtotal = 1146 intel_de_read(dev_priv, 1147 BXT_MIPI_TRANS_VTOTAL(port)); 1148 1149 hactive = adjusted_mode->crtc_hdisplay; 1150 hfp = intel_de_read(dev_priv, MIPI_HFP_COUNT(port)); 1151 1152 /* 1153 * Meaningful for video mode non-burst sync pulse mode only, 1154 * can be zero for non-burst sync events and burst modes 1155 */ 1156 hsync = intel_de_read(dev_priv, MIPI_HSYNC_PADDING_COUNT(port)); 1157 hbp = intel_de_read(dev_priv, MIPI_HBP_COUNT(port)); 1158 1159 /* harizontal values are in terms of high speed byte clock */ 1160 hfp = pixels_from_txbyteclkhs(hfp, bpp, lane_count, 1161 intel_dsi->burst_mode_ratio); 1162 hsync = pixels_from_txbyteclkhs(hsync, bpp, lane_count, 1163 intel_dsi->burst_mode_ratio); 1164 hbp = pixels_from_txbyteclkhs(hbp, bpp, lane_count, 1165 intel_dsi->burst_mode_ratio); 1166 1167 if (intel_dsi->dual_link) { 1168 hfp *= 2; 1169 hsync *= 2; 1170 hbp *= 2; 1171 } 1172 1173 /* vertical values are in terms of lines */ 1174 vfp = intel_de_read(dev_priv, MIPI_VFP_COUNT(port)); 1175 vsync = intel_de_read(dev_priv, MIPI_VSYNC_PADDING_COUNT(port)); 1176 vbp = intel_de_read(dev_priv, MIPI_VBP_COUNT(port)); 1177 1178 adjusted_mode->crtc_htotal = hactive + hfp + hsync + hbp; 1179 adjusted_mode->crtc_hsync_start = hfp + adjusted_mode->crtc_hdisplay; 1180 adjusted_mode->crtc_hsync_end = hsync + adjusted_mode->crtc_hsync_start; 1181 adjusted_mode->crtc_hblank_start = adjusted_mode->crtc_hdisplay; 1182 adjusted_mode->crtc_hblank_end = adjusted_mode->crtc_htotal; 1183 1184 adjusted_mode->crtc_vsync_start = vfp + adjusted_mode->crtc_vdisplay; 1185 adjusted_mode->crtc_vsync_end = vsync + adjusted_mode->crtc_vsync_start; 1186 adjusted_mode->crtc_vblank_start = adjusted_mode->crtc_vdisplay; 1187 adjusted_mode->crtc_vblank_end = adjusted_mode->crtc_vtotal; 1188 1189 /* 1190 * In BXT DSI there is no regs programmed with few horizontal timings 1191 * in Pixels but txbyteclkhs.. So retrieval process adds some 1192 * ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs. 1193 * Actually here for the given adjusted_mode, we are calculating the 1194 * value programmed to the port and then back to the horizontal timing 1195 * param in pixels. This is the expected value, including roundup errors 1196 * And if that is same as retrieved value from port, then 1197 * (HW state) adjusted_mode's horizontal timings are corrected to 1198 * match with SW state to nullify the errors. 1199 */ 1200 /* Calculating the value programmed to the Port register */ 1201 hfp_sw = adjusted_mode_sw->crtc_hsync_start - 1202 adjusted_mode_sw->crtc_hdisplay; 1203 hsync_sw = adjusted_mode_sw->crtc_hsync_end - 1204 adjusted_mode_sw->crtc_hsync_start; 1205 hbp_sw = adjusted_mode_sw->crtc_htotal - 1206 adjusted_mode_sw->crtc_hsync_end; 1207 1208 if (intel_dsi->dual_link) { 1209 hfp_sw /= 2; 1210 hsync_sw /= 2; 1211 hbp_sw /= 2; 1212 } 1213 1214 hfp_sw = txbyteclkhs(hfp_sw, bpp, lane_count, 1215 intel_dsi->burst_mode_ratio); 1216 hsync_sw = txbyteclkhs(hsync_sw, bpp, lane_count, 1217 intel_dsi->burst_mode_ratio); 1218 hbp_sw = txbyteclkhs(hbp_sw, bpp, lane_count, 1219 intel_dsi->burst_mode_ratio); 1220 1221 /* Reverse calculating the adjusted mode parameters from port reg vals*/ 1222 hfp_sw = pixels_from_txbyteclkhs(hfp_sw, bpp, lane_count, 1223 intel_dsi->burst_mode_ratio); 1224 hsync_sw = pixels_from_txbyteclkhs(hsync_sw, bpp, lane_count, 1225 intel_dsi->burst_mode_ratio); 1226 hbp_sw = pixels_from_txbyteclkhs(hbp_sw, bpp, lane_count, 1227 intel_dsi->burst_mode_ratio); 1228 1229 if (intel_dsi->dual_link) { 1230 hfp_sw *= 2; 1231 hsync_sw *= 2; 1232 hbp_sw *= 2; 1233 } 1234 1235 crtc_htotal_sw = adjusted_mode_sw->crtc_hdisplay + hfp_sw + 1236 hsync_sw + hbp_sw; 1237 crtc_hsync_start_sw = hfp_sw + adjusted_mode_sw->crtc_hdisplay; 1238 crtc_hsync_end_sw = hsync_sw + crtc_hsync_start_sw; 1239 crtc_hblank_start_sw = adjusted_mode_sw->crtc_hdisplay; 1240 crtc_hblank_end_sw = crtc_htotal_sw; 1241 1242 if (adjusted_mode->crtc_htotal == crtc_htotal_sw) 1243 adjusted_mode->crtc_htotal = adjusted_mode_sw->crtc_htotal; 1244 1245 if (adjusted_mode->crtc_hsync_start == crtc_hsync_start_sw) 1246 adjusted_mode->crtc_hsync_start = 1247 adjusted_mode_sw->crtc_hsync_start; 1248 1249 if (adjusted_mode->crtc_hsync_end == crtc_hsync_end_sw) 1250 adjusted_mode->crtc_hsync_end = 1251 adjusted_mode_sw->crtc_hsync_end; 1252 1253 if (adjusted_mode->crtc_hblank_start == crtc_hblank_start_sw) 1254 adjusted_mode->crtc_hblank_start = 1255 adjusted_mode_sw->crtc_hblank_start; 1256 1257 if (adjusted_mode->crtc_hblank_end == crtc_hblank_end_sw) 1258 adjusted_mode->crtc_hblank_end = 1259 adjusted_mode_sw->crtc_hblank_end; 1260 } 1261 1262 static void intel_dsi_get_config(struct intel_encoder *encoder, 1263 struct intel_crtc_state *pipe_config) 1264 { 1265 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 1266 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 1267 u32 pclk; 1268 1269 drm_dbg_kms(&dev_priv->drm, "\n"); 1270 1271 pipe_config->output_types |= BIT(INTEL_OUTPUT_DSI); 1272 1273 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 1274 bxt_dsi_get_pipe_config(encoder, pipe_config); 1275 pclk = bxt_dsi_get_pclk(encoder, pipe_config); 1276 } else { 1277 pclk = vlv_dsi_get_pclk(encoder, pipe_config); 1278 } 1279 1280 if (intel_dsi->dual_link) 1281 pclk *= 2; 1282 1283 if (pclk) { 1284 pipe_config->hw.adjusted_mode.crtc_clock = pclk; 1285 pipe_config->port_clock = pclk; 1286 } 1287 } 1288 1289 /* return txclkesc cycles in terms of divider and duration in us */ 1290 static u16 txclkesc(u32 divider, unsigned int us) 1291 { 1292 switch (divider) { 1293 case ESCAPE_CLOCK_DIVIDER_1: 1294 default: 1295 return 20 * us; 1296 case ESCAPE_CLOCK_DIVIDER_2: 1297 return 10 * us; 1298 case ESCAPE_CLOCK_DIVIDER_4: 1299 return 5 * us; 1300 } 1301 } 1302 1303 static void set_dsi_timings(struct drm_encoder *encoder, 1304 const struct drm_display_mode *adjusted_mode) 1305 { 1306 struct drm_device *dev = encoder->dev; 1307 struct drm_i915_private *dev_priv = to_i915(dev); 1308 struct intel_dsi *intel_dsi = enc_to_intel_dsi(to_intel_encoder(encoder)); 1309 enum port port; 1310 unsigned int bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format); 1311 unsigned int lane_count = intel_dsi->lane_count; 1312 1313 u16 hactive, hfp, hsync, hbp, vfp, vsync, vbp; 1314 1315 hactive = adjusted_mode->crtc_hdisplay; 1316 hfp = adjusted_mode->crtc_hsync_start - adjusted_mode->crtc_hdisplay; 1317 hsync = adjusted_mode->crtc_hsync_end - adjusted_mode->crtc_hsync_start; 1318 hbp = adjusted_mode->crtc_htotal - adjusted_mode->crtc_hsync_end; 1319 1320 if (intel_dsi->dual_link) { 1321 hactive /= 2; 1322 if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK) 1323 hactive += intel_dsi->pixel_overlap; 1324 hfp /= 2; 1325 hsync /= 2; 1326 hbp /= 2; 1327 } 1328 1329 vfp = adjusted_mode->crtc_vsync_start - adjusted_mode->crtc_vdisplay; 1330 vsync = adjusted_mode->crtc_vsync_end - adjusted_mode->crtc_vsync_start; 1331 vbp = adjusted_mode->crtc_vtotal - adjusted_mode->crtc_vsync_end; 1332 1333 /* horizontal values are in terms of high speed byte clock */ 1334 hactive = txbyteclkhs(hactive, bpp, lane_count, 1335 intel_dsi->burst_mode_ratio); 1336 hfp = txbyteclkhs(hfp, bpp, lane_count, intel_dsi->burst_mode_ratio); 1337 hsync = txbyteclkhs(hsync, bpp, lane_count, 1338 intel_dsi->burst_mode_ratio); 1339 hbp = txbyteclkhs(hbp, bpp, lane_count, intel_dsi->burst_mode_ratio); 1340 1341 for_each_dsi_port(port, intel_dsi->ports) { 1342 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 1343 /* 1344 * Program hdisplay and vdisplay on MIPI transcoder. 1345 * This is different from calculated hactive and 1346 * vactive, as they are calculated per channel basis, 1347 * whereas these values should be based on resolution. 1348 */ 1349 intel_de_write(dev_priv, BXT_MIPI_TRANS_HACTIVE(port), 1350 adjusted_mode->crtc_hdisplay); 1351 intel_de_write(dev_priv, BXT_MIPI_TRANS_VACTIVE(port), 1352 adjusted_mode->crtc_vdisplay); 1353 intel_de_write(dev_priv, BXT_MIPI_TRANS_VTOTAL(port), 1354 adjusted_mode->crtc_vtotal); 1355 } 1356 1357 intel_de_write(dev_priv, MIPI_HACTIVE_AREA_COUNT(port), 1358 hactive); 1359 intel_de_write(dev_priv, MIPI_HFP_COUNT(port), hfp); 1360 1361 /* meaningful for video mode non-burst sync pulse mode only, 1362 * can be zero for non-burst sync events and burst modes */ 1363 intel_de_write(dev_priv, MIPI_HSYNC_PADDING_COUNT(port), 1364 hsync); 1365 intel_de_write(dev_priv, MIPI_HBP_COUNT(port), hbp); 1366 1367 /* vertical values are in terms of lines */ 1368 intel_de_write(dev_priv, MIPI_VFP_COUNT(port), vfp); 1369 intel_de_write(dev_priv, MIPI_VSYNC_PADDING_COUNT(port), 1370 vsync); 1371 intel_de_write(dev_priv, MIPI_VBP_COUNT(port), vbp); 1372 } 1373 } 1374 1375 static u32 pixel_format_to_reg(enum mipi_dsi_pixel_format fmt) 1376 { 1377 switch (fmt) { 1378 case MIPI_DSI_FMT_RGB888: 1379 return VID_MODE_FORMAT_RGB888; 1380 case MIPI_DSI_FMT_RGB666: 1381 return VID_MODE_FORMAT_RGB666; 1382 case MIPI_DSI_FMT_RGB666_PACKED: 1383 return VID_MODE_FORMAT_RGB666_PACKED; 1384 case MIPI_DSI_FMT_RGB565: 1385 return VID_MODE_FORMAT_RGB565; 1386 default: 1387 MISSING_CASE(fmt); 1388 return VID_MODE_FORMAT_RGB666; 1389 } 1390 } 1391 1392 static void intel_dsi_prepare(struct intel_encoder *intel_encoder, 1393 const struct intel_crtc_state *pipe_config) 1394 { 1395 struct drm_encoder *encoder = &intel_encoder->base; 1396 struct drm_device *dev = encoder->dev; 1397 struct drm_i915_private *dev_priv = to_i915(dev); 1398 struct intel_crtc *crtc = to_intel_crtc(pipe_config->uapi.crtc); 1399 struct intel_dsi *intel_dsi = enc_to_intel_dsi(to_intel_encoder(encoder)); 1400 const struct drm_display_mode *adjusted_mode = &pipe_config->hw.adjusted_mode; 1401 enum port port; 1402 unsigned int bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format); 1403 u32 val, tmp; 1404 u16 mode_hdisplay; 1405 1406 drm_dbg_kms(&dev_priv->drm, "pipe %c\n", pipe_name(crtc->pipe)); 1407 1408 mode_hdisplay = adjusted_mode->crtc_hdisplay; 1409 1410 if (intel_dsi->dual_link) { 1411 mode_hdisplay /= 2; 1412 if (intel_dsi->dual_link == DSI_DUAL_LINK_FRONT_BACK) 1413 mode_hdisplay += intel_dsi->pixel_overlap; 1414 } 1415 1416 for_each_dsi_port(port, intel_dsi->ports) { 1417 if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) { 1418 /* 1419 * escape clock divider, 20MHz, shared for A and C. 1420 * device ready must be off when doing this! txclkesc? 1421 */ 1422 tmp = intel_de_read(dev_priv, MIPI_CTRL(PORT_A)); 1423 tmp &= ~ESCAPE_CLOCK_DIVIDER_MASK; 1424 intel_de_write(dev_priv, MIPI_CTRL(PORT_A), 1425 tmp | ESCAPE_CLOCK_DIVIDER_1); 1426 1427 /* read request priority is per pipe */ 1428 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 1429 tmp &= ~READ_REQUEST_PRIORITY_MASK; 1430 intel_de_write(dev_priv, MIPI_CTRL(port), 1431 tmp | READ_REQUEST_PRIORITY_HIGH); 1432 } else if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 1433 enum pipe pipe = crtc->pipe; 1434 1435 tmp = intel_de_read(dev_priv, MIPI_CTRL(port)); 1436 tmp &= ~BXT_PIPE_SELECT_MASK; 1437 1438 tmp |= BXT_PIPE_SELECT(pipe); 1439 intel_de_write(dev_priv, MIPI_CTRL(port), tmp); 1440 } 1441 1442 /* XXX: why here, why like this? handling in irq handler?! */ 1443 intel_de_write(dev_priv, MIPI_INTR_STAT(port), 0xffffffff); 1444 intel_de_write(dev_priv, MIPI_INTR_EN(port), 0xffffffff); 1445 1446 intel_de_write(dev_priv, MIPI_DPHY_PARAM(port), 1447 intel_dsi->dphy_reg); 1448 1449 intel_de_write(dev_priv, MIPI_DPI_RESOLUTION(port), 1450 adjusted_mode->crtc_vdisplay << VERTICAL_ADDRESS_SHIFT | mode_hdisplay << HORIZONTAL_ADDRESS_SHIFT); 1451 } 1452 1453 set_dsi_timings(encoder, adjusted_mode); 1454 1455 val = intel_dsi->lane_count << DATA_LANES_PRG_REG_SHIFT; 1456 if (is_cmd_mode(intel_dsi)) { 1457 val |= intel_dsi->channel << CMD_MODE_CHANNEL_NUMBER_SHIFT; 1458 val |= CMD_MODE_DATA_WIDTH_8_BIT; /* XXX */ 1459 } else { 1460 val |= intel_dsi->channel << VID_MODE_CHANNEL_NUMBER_SHIFT; 1461 val |= pixel_format_to_reg(intel_dsi->pixel_format); 1462 } 1463 1464 tmp = 0; 1465 if (intel_dsi->eotp_pkt == 0) 1466 tmp |= EOT_DISABLE; 1467 if (intel_dsi->clock_stop) 1468 tmp |= CLOCKSTOP; 1469 1470 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) { 1471 tmp |= BXT_DPHY_DEFEATURE_EN; 1472 if (!is_cmd_mode(intel_dsi)) 1473 tmp |= BXT_DEFEATURE_DPI_FIFO_CTR; 1474 } 1475 1476 for_each_dsi_port(port, intel_dsi->ports) { 1477 intel_de_write(dev_priv, MIPI_DSI_FUNC_PRG(port), val); 1478 1479 /* timeouts for recovery. one frame IIUC. if counter expires, 1480 * EOT and stop state. */ 1481 1482 /* 1483 * In burst mode, value greater than one DPI line Time in byte 1484 * clock (txbyteclkhs) To timeout this timer 1+ of the above 1485 * said value is recommended. 1486 * 1487 * In non-burst mode, Value greater than one DPI frame time in 1488 * byte clock(txbyteclkhs) To timeout this timer 1+ of the above 1489 * said value is recommended. 1490 * 1491 * In DBI only mode, value greater than one DBI frame time in 1492 * byte clock(txbyteclkhs) To timeout this timer 1+ of the above 1493 * said value is recommended. 1494 */ 1495 1496 if (is_vid_mode(intel_dsi) && 1497 intel_dsi->video_mode == BURST_MODE) { 1498 intel_de_write(dev_priv, MIPI_HS_TX_TIMEOUT(port), 1499 txbyteclkhs(adjusted_mode->crtc_htotal, bpp, intel_dsi->lane_count, intel_dsi->burst_mode_ratio) + 1); 1500 } else { 1501 intel_de_write(dev_priv, MIPI_HS_TX_TIMEOUT(port), 1502 txbyteclkhs(adjusted_mode->crtc_vtotal * adjusted_mode->crtc_htotal, bpp, intel_dsi->lane_count, intel_dsi->burst_mode_ratio) + 1); 1503 } 1504 intel_de_write(dev_priv, MIPI_LP_RX_TIMEOUT(port), 1505 intel_dsi->lp_rx_timeout); 1506 intel_de_write(dev_priv, MIPI_TURN_AROUND_TIMEOUT(port), 1507 intel_dsi->turn_arnd_val); 1508 intel_de_write(dev_priv, MIPI_DEVICE_RESET_TIMER(port), 1509 intel_dsi->rst_timer_val); 1510 1511 /* dphy stuff */ 1512 1513 /* in terms of low power clock */ 1514 intel_de_write(dev_priv, MIPI_INIT_COUNT(port), 1515 txclkesc(intel_dsi->escape_clk_div, 100)); 1516 1517 if ((IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) && 1518 !intel_dsi->dual_link) { 1519 /* 1520 * BXT spec says write MIPI_INIT_COUNT for 1521 * both the ports, even if only one is 1522 * getting used. So write the other port 1523 * if not in dual link mode. 1524 */ 1525 intel_de_write(dev_priv, 1526 MIPI_INIT_COUNT(port == PORT_A ? PORT_C : PORT_A), 1527 intel_dsi->init_count); 1528 } 1529 1530 /* recovery disables */ 1531 intel_de_write(dev_priv, MIPI_EOT_DISABLE(port), tmp); 1532 1533 /* in terms of low power clock */ 1534 intel_de_write(dev_priv, MIPI_INIT_COUNT(port), 1535 intel_dsi->init_count); 1536 1537 /* in terms of txbyteclkhs. actual high to low switch + 1538 * MIPI_STOP_STATE_STALL * MIPI_LP_BYTECLK. 1539 * 1540 * XXX: write MIPI_STOP_STATE_STALL? 1541 */ 1542 intel_de_write(dev_priv, MIPI_HIGH_LOW_SWITCH_COUNT(port), 1543 intel_dsi->hs_to_lp_count); 1544 1545 /* XXX: low power clock equivalence in terms of byte clock. 1546 * the number of byte clocks occupied in one low power clock. 1547 * based on txbyteclkhs and txclkesc. 1548 * txclkesc time / txbyteclk time * (105 + MIPI_STOP_STATE_STALL 1549 * ) / 105.??? 1550 */ 1551 intel_de_write(dev_priv, MIPI_LP_BYTECLK(port), 1552 intel_dsi->lp_byte_clk); 1553 1554 if (IS_GEMINILAKE(dev_priv)) { 1555 intel_de_write(dev_priv, MIPI_TLPX_TIME_COUNT(port), 1556 intel_dsi->lp_byte_clk); 1557 /* Shadow of DPHY reg */ 1558 intel_de_write(dev_priv, MIPI_CLK_LANE_TIMING(port), 1559 intel_dsi->dphy_reg); 1560 } 1561 1562 /* the bw essential for transmitting 16 long packets containing 1563 * 252 bytes meant for dcs write memory command is programmed in 1564 * this register in terms of byte clocks. based on dsi transfer 1565 * rate and the number of lanes configured the time taken to 1566 * transmit 16 long packets in a dsi stream varies. */ 1567 intel_de_write(dev_priv, MIPI_DBI_BW_CTRL(port), 1568 intel_dsi->bw_timer); 1569 1570 intel_de_write(dev_priv, MIPI_CLK_LANE_SWITCH_TIME_CNT(port), 1571 intel_dsi->clk_lp_to_hs_count << LP_HS_SSW_CNT_SHIFT | intel_dsi->clk_hs_to_lp_count << HS_LP_PWR_SW_CNT_SHIFT); 1572 1573 if (is_vid_mode(intel_dsi)) { 1574 u32 fmt = intel_dsi->video_frmt_cfg_bits | IP_TG_CONFIG; 1575 1576 /* 1577 * Some panels might have resolution which is not a 1578 * multiple of 64 like 1366 x 768. Enable RANDOM 1579 * resolution support for such panels by default. 1580 */ 1581 fmt |= RANDOM_DPI_DISPLAY_RESOLUTION; 1582 1583 switch (intel_dsi->video_mode) { 1584 default: 1585 MISSING_CASE(intel_dsi->video_mode); 1586 fallthrough; 1587 case NON_BURST_SYNC_EVENTS: 1588 fmt |= VIDEO_MODE_NON_BURST_WITH_SYNC_EVENTS; 1589 break; 1590 case NON_BURST_SYNC_PULSE: 1591 fmt |= VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE; 1592 break; 1593 case BURST_MODE: 1594 fmt |= VIDEO_MODE_BURST; 1595 break; 1596 } 1597 1598 intel_de_write(dev_priv, MIPI_VIDEO_MODE_FORMAT(port), fmt); 1599 } 1600 } 1601 } 1602 1603 static void intel_dsi_unprepare(struct intel_encoder *encoder) 1604 { 1605 struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); 1606 struct intel_dsi *intel_dsi = enc_to_intel_dsi(encoder); 1607 enum port port; 1608 u32 val; 1609 1610 if (IS_GEMINILAKE(dev_priv)) 1611 return; 1612 1613 for_each_dsi_port(port, intel_dsi->ports) { 1614 /* Panel commands can be sent when clock is in LP11 */ 1615 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 0x0); 1616 1617 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) 1618 bxt_dsi_reset_clocks(encoder, port); 1619 else 1620 vlv_dsi_reset_clocks(encoder, port); 1621 intel_de_write(dev_priv, MIPI_EOT_DISABLE(port), CLOCKSTOP); 1622 1623 val = intel_de_read(dev_priv, MIPI_DSI_FUNC_PRG(port)); 1624 val &= ~VID_MODE_FORMAT_MASK; 1625 intel_de_write(dev_priv, MIPI_DSI_FUNC_PRG(port), val); 1626 1627 intel_de_write(dev_priv, MIPI_DEVICE_READY(port), 0x1); 1628 } 1629 } 1630 1631 static void intel_dsi_encoder_destroy(struct drm_encoder *encoder) 1632 { 1633 struct intel_dsi *intel_dsi = enc_to_intel_dsi(to_intel_encoder(encoder)); 1634 1635 intel_dsi_vbt_gpio_cleanup(intel_dsi); 1636 intel_encoder_destroy(encoder); 1637 } 1638 1639 static const struct drm_encoder_funcs intel_dsi_funcs = { 1640 .destroy = intel_dsi_encoder_destroy, 1641 }; 1642 1643 static const struct drm_connector_helper_funcs intel_dsi_connector_helper_funcs = { 1644 .get_modes = intel_dsi_get_modes, 1645 .mode_valid = intel_dsi_mode_valid, 1646 .atomic_check = intel_digital_connector_atomic_check, 1647 }; 1648 1649 static const struct drm_connector_funcs intel_dsi_connector_funcs = { 1650 .detect = intel_panel_detect, 1651 .late_register = intel_connector_register, 1652 .early_unregister = intel_connector_unregister, 1653 .destroy = intel_connector_destroy, 1654 .fill_modes = drm_helper_probe_single_connector_modes, 1655 .atomic_get_property = intel_digital_connector_atomic_get_property, 1656 .atomic_set_property = intel_digital_connector_atomic_set_property, 1657 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1658 .atomic_duplicate_state = intel_digital_connector_duplicate_state, 1659 }; 1660 1661 static void vlv_dsi_add_properties(struct intel_connector *connector) 1662 { 1663 struct drm_i915_private *dev_priv = to_i915(connector->base.dev); 1664 const struct drm_display_mode *fixed_mode = 1665 intel_panel_preferred_fixed_mode(connector); 1666 u32 allowed_scalers; 1667 1668 allowed_scalers = BIT(DRM_MODE_SCALE_ASPECT) | BIT(DRM_MODE_SCALE_FULLSCREEN); 1669 if (!HAS_GMCH(dev_priv)) 1670 allowed_scalers |= BIT(DRM_MODE_SCALE_CENTER); 1671 1672 drm_connector_attach_scaling_mode_property(&connector->base, 1673 allowed_scalers); 1674 1675 connector->base.state->scaling_mode = DRM_MODE_SCALE_ASPECT; 1676 1677 drm_connector_set_panel_orientation_with_quirk(&connector->base, 1678 intel_dsi_get_panel_orientation(connector), 1679 fixed_mode->hdisplay, 1680 fixed_mode->vdisplay); 1681 } 1682 1683 #define NS_KHZ_RATIO 1000000 1684 1685 #define PREPARE_CNT_MAX 0x3F 1686 #define EXIT_ZERO_CNT_MAX 0x3F 1687 #define CLK_ZERO_CNT_MAX 0xFF 1688 #define TRAIL_CNT_MAX 0x1F 1689 1690 static void vlv_dphy_param_init(struct intel_dsi *intel_dsi) 1691 { 1692 struct drm_device *dev = intel_dsi->base.base.dev; 1693 struct drm_i915_private *dev_priv = to_i915(dev); 1694 struct intel_connector *connector = intel_dsi->attached_connector; 1695 struct mipi_config *mipi_config = connector->panel.vbt.dsi.config; 1696 u32 tlpx_ns, extra_byte_count, tlpx_ui; 1697 u32 ui_num, ui_den; 1698 u32 prepare_cnt, exit_zero_cnt, clk_zero_cnt, trail_cnt; 1699 u32 ths_prepare_ns, tclk_trail_ns; 1700 u32 tclk_prepare_clkzero, ths_prepare_hszero; 1701 u32 lp_to_hs_switch, hs_to_lp_switch; 1702 u32 mul; 1703 1704 tlpx_ns = intel_dsi_tlpx_ns(intel_dsi); 1705 1706 switch (intel_dsi->lane_count) { 1707 case 1: 1708 case 2: 1709 extra_byte_count = 2; 1710 break; 1711 case 3: 1712 extra_byte_count = 4; 1713 break; 1714 case 4: 1715 default: 1716 extra_byte_count = 3; 1717 break; 1718 } 1719 1720 /* in Kbps */ 1721 ui_num = NS_KHZ_RATIO; 1722 ui_den = intel_dsi_bitrate(intel_dsi); 1723 1724 tclk_prepare_clkzero = mipi_config->tclk_prepare_clkzero; 1725 ths_prepare_hszero = mipi_config->ths_prepare_hszero; 1726 1727 /* 1728 * B060 1729 * LP byte clock = TLPX/ (8UI) 1730 */ 1731 intel_dsi->lp_byte_clk = DIV_ROUND_UP(tlpx_ns * ui_den, 8 * ui_num); 1732 1733 /* DDR clock period = 2 * UI 1734 * UI(sec) = 1/(bitrate * 10^3) (bitrate is in KHZ) 1735 * UI(nsec) = 10^6 / bitrate 1736 * DDR clock period (nsec) = 2 * UI = (2 * 10^6)/ bitrate 1737 * DDR clock count = ns_value / DDR clock period 1738 * 1739 * For GEMINILAKE dphy_param_reg will be programmed in terms of 1740 * HS byte clock count for other platform in HS ddr clock count 1741 */ 1742 mul = IS_GEMINILAKE(dev_priv) ? 8 : 2; 1743 ths_prepare_ns = max(mipi_config->ths_prepare, 1744 mipi_config->tclk_prepare); 1745 1746 /* prepare count */ 1747 prepare_cnt = DIV_ROUND_UP(ths_prepare_ns * ui_den, ui_num * mul); 1748 1749 if (prepare_cnt > PREPARE_CNT_MAX) { 1750 drm_dbg_kms(&dev_priv->drm, "prepare count too high %u\n", 1751 prepare_cnt); 1752 prepare_cnt = PREPARE_CNT_MAX; 1753 } 1754 1755 /* exit zero count */ 1756 exit_zero_cnt = DIV_ROUND_UP( 1757 (ths_prepare_hszero - ths_prepare_ns) * ui_den, 1758 ui_num * mul 1759 ); 1760 1761 /* 1762 * Exit zero is unified val ths_zero and ths_exit 1763 * minimum value for ths_exit = 110ns 1764 * min (exit_zero_cnt * 2) = 110/UI 1765 * exit_zero_cnt = 55/UI 1766 */ 1767 if (exit_zero_cnt < (55 * ui_den / ui_num) && (55 * ui_den) % ui_num) 1768 exit_zero_cnt += 1; 1769 1770 if (exit_zero_cnt > EXIT_ZERO_CNT_MAX) { 1771 drm_dbg_kms(&dev_priv->drm, "exit zero count too high %u\n", 1772 exit_zero_cnt); 1773 exit_zero_cnt = EXIT_ZERO_CNT_MAX; 1774 } 1775 1776 /* clk zero count */ 1777 clk_zero_cnt = DIV_ROUND_UP( 1778 (tclk_prepare_clkzero - ths_prepare_ns) 1779 * ui_den, ui_num * mul); 1780 1781 if (clk_zero_cnt > CLK_ZERO_CNT_MAX) { 1782 drm_dbg_kms(&dev_priv->drm, "clock zero count too high %u\n", 1783 clk_zero_cnt); 1784 clk_zero_cnt = CLK_ZERO_CNT_MAX; 1785 } 1786 1787 /* trail count */ 1788 tclk_trail_ns = max(mipi_config->tclk_trail, mipi_config->ths_trail); 1789 trail_cnt = DIV_ROUND_UP(tclk_trail_ns * ui_den, ui_num * mul); 1790 1791 if (trail_cnt > TRAIL_CNT_MAX) { 1792 drm_dbg_kms(&dev_priv->drm, "trail count too high %u\n", 1793 trail_cnt); 1794 trail_cnt = TRAIL_CNT_MAX; 1795 } 1796 1797 /* B080 */ 1798 intel_dsi->dphy_reg = exit_zero_cnt << 24 | trail_cnt << 16 | 1799 clk_zero_cnt << 8 | prepare_cnt; 1800 1801 /* 1802 * LP to HS switch count = 4TLPX + PREP_COUNT * mul + EXIT_ZERO_COUNT * 1803 * mul + 10UI + Extra Byte Count 1804 * 1805 * HS to LP switch count = THS-TRAIL + 2TLPX + Extra Byte Count 1806 * Extra Byte Count is calculated according to number of lanes. 1807 * High Low Switch Count is the Max of LP to HS and 1808 * HS to LP switch count 1809 * 1810 */ 1811 tlpx_ui = DIV_ROUND_UP(tlpx_ns * ui_den, ui_num); 1812 1813 /* B044 */ 1814 /* FIXME: 1815 * The comment above does not match with the code */ 1816 lp_to_hs_switch = DIV_ROUND_UP(4 * tlpx_ui + prepare_cnt * mul + 1817 exit_zero_cnt * mul + 10, 8); 1818 1819 hs_to_lp_switch = DIV_ROUND_UP(mipi_config->ths_trail + 2 * tlpx_ui, 8); 1820 1821 intel_dsi->hs_to_lp_count = max(lp_to_hs_switch, hs_to_lp_switch); 1822 intel_dsi->hs_to_lp_count += extra_byte_count; 1823 1824 /* B088 */ 1825 /* LP -> HS for clock lanes 1826 * LP clk sync + LP11 + LP01 + tclk_prepare + tclk_zero + 1827 * extra byte count 1828 * 2TPLX + 1TLPX + 1 TPLX(in ns) + prepare_cnt * 2 + clk_zero_cnt * 1829 * 2(in UI) + extra byte count 1830 * In byteclks = (4TLPX + prepare_cnt * 2 + clk_zero_cnt *2 (in UI)) / 1831 * 8 + extra byte count 1832 */ 1833 intel_dsi->clk_lp_to_hs_count = 1834 DIV_ROUND_UP( 1835 4 * tlpx_ui + prepare_cnt * 2 + 1836 clk_zero_cnt * 2, 1837 8); 1838 1839 intel_dsi->clk_lp_to_hs_count += extra_byte_count; 1840 1841 /* HS->LP for Clock Lanes 1842 * Low Power clock synchronisations + 1Tx byteclk + tclk_trail + 1843 * Extra byte count 1844 * 2TLPX + 8UI + (trail_count*2)(in UI) + Extra byte count 1845 * In byteclks = (2*TLpx(in UI) + trail_count*2 +8)(in UI)/8 + 1846 * Extra byte count 1847 */ 1848 intel_dsi->clk_hs_to_lp_count = 1849 DIV_ROUND_UP(2 * tlpx_ui + trail_cnt * 2 + 8, 1850 8); 1851 intel_dsi->clk_hs_to_lp_count += extra_byte_count; 1852 1853 intel_dsi_log_params(intel_dsi); 1854 } 1855 1856 void vlv_dsi_init(struct drm_i915_private *dev_priv) 1857 { 1858 struct drm_device *dev = &dev_priv->drm; 1859 struct intel_dsi *intel_dsi; 1860 struct intel_encoder *intel_encoder; 1861 struct drm_encoder *encoder; 1862 struct intel_connector *intel_connector; 1863 struct drm_connector *connector; 1864 struct drm_display_mode *current_mode; 1865 enum port port; 1866 enum pipe pipe; 1867 1868 drm_dbg_kms(&dev_priv->drm, "\n"); 1869 1870 /* There is no detection method for MIPI so rely on VBT */ 1871 if (!intel_bios_is_dsi_present(dev_priv, &port)) 1872 return; 1873 1874 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) 1875 dev_priv->mipi_mmio_base = BXT_MIPI_BASE; 1876 else 1877 dev_priv->mipi_mmio_base = VLV_MIPI_BASE; 1878 1879 intel_dsi = kzalloc(sizeof(*intel_dsi), GFP_KERNEL); 1880 if (!intel_dsi) 1881 return; 1882 1883 intel_connector = intel_connector_alloc(); 1884 if (!intel_connector) { 1885 kfree(intel_dsi); 1886 return; 1887 } 1888 1889 intel_encoder = &intel_dsi->base; 1890 encoder = &intel_encoder->base; 1891 intel_dsi->attached_connector = intel_connector; 1892 1893 connector = &intel_connector->base; 1894 1895 drm_encoder_init(dev, encoder, &intel_dsi_funcs, DRM_MODE_ENCODER_DSI, 1896 "DSI %c", port_name(port)); 1897 1898 intel_encoder->compute_config = intel_dsi_compute_config; 1899 intel_encoder->pre_enable = intel_dsi_pre_enable; 1900 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) 1901 intel_encoder->enable = bxt_dsi_enable; 1902 intel_encoder->disable = intel_dsi_disable; 1903 intel_encoder->post_disable = intel_dsi_post_disable; 1904 intel_encoder->get_hw_state = intel_dsi_get_hw_state; 1905 intel_encoder->get_config = intel_dsi_get_config; 1906 intel_encoder->update_pipe = intel_backlight_update; 1907 intel_encoder->shutdown = intel_dsi_shutdown; 1908 1909 intel_connector->get_hw_state = intel_connector_get_hw_state; 1910 1911 intel_encoder->port = port; 1912 intel_encoder->type = INTEL_OUTPUT_DSI; 1913 intel_encoder->power_domain = POWER_DOMAIN_PORT_DSI; 1914 intel_encoder->cloneable = 0; 1915 1916 /* 1917 * On BYT/CHV, pipe A maps to MIPI DSI port A, pipe B maps to MIPI DSI 1918 * port C. BXT isn't limited like this. 1919 */ 1920 if (IS_GEMINILAKE(dev_priv) || IS_BROXTON(dev_priv)) 1921 intel_encoder->pipe_mask = ~0; 1922 else if (port == PORT_A) 1923 intel_encoder->pipe_mask = BIT(PIPE_A); 1924 else 1925 intel_encoder->pipe_mask = BIT(PIPE_B); 1926 1927 intel_dsi->panel_power_off_time = ktime_get_boottime(); 1928 1929 intel_bios_init_panel(dev_priv, &intel_connector->panel, NULL, NULL); 1930 1931 if (intel_connector->panel.vbt.dsi.config->dual_link) 1932 intel_dsi->ports = BIT(PORT_A) | BIT(PORT_C); 1933 else 1934 intel_dsi->ports = BIT(port); 1935 1936 intel_dsi->dcs_backlight_ports = intel_connector->panel.vbt.dsi.bl_ports; 1937 intel_dsi->dcs_cabc_ports = intel_connector->panel.vbt.dsi.cabc_ports; 1938 1939 /* Create a DSI host (and a device) for each port. */ 1940 for_each_dsi_port(port, intel_dsi->ports) { 1941 struct intel_dsi_host *host; 1942 1943 host = intel_dsi_host_init(intel_dsi, &intel_dsi_host_ops, 1944 port); 1945 if (!host) 1946 goto err; 1947 1948 intel_dsi->dsi_hosts[port] = host; 1949 } 1950 1951 if (!intel_dsi_vbt_init(intel_dsi, MIPI_DSI_GENERIC_PANEL_ID)) { 1952 drm_dbg_kms(&dev_priv->drm, "no device found\n"); 1953 goto err; 1954 } 1955 1956 /* Use clock read-back from current hw-state for fastboot */ 1957 current_mode = intel_encoder_current_mode(intel_encoder); 1958 if (current_mode) { 1959 drm_dbg_kms(&dev_priv->drm, "Calculated pclk %d GOP %d\n", 1960 intel_dsi->pclk, current_mode->clock); 1961 if (intel_fuzzy_clock_check(intel_dsi->pclk, 1962 current_mode->clock)) { 1963 drm_dbg_kms(&dev_priv->drm, "Using GOP pclk\n"); 1964 intel_dsi->pclk = current_mode->clock; 1965 } 1966 1967 kfree(current_mode); 1968 } 1969 1970 vlv_dphy_param_init(intel_dsi); 1971 1972 intel_dsi_vbt_gpio_init(intel_dsi, 1973 intel_dsi_get_hw_state(intel_encoder, &pipe)); 1974 1975 drm_connector_init(dev, connector, &intel_dsi_connector_funcs, 1976 DRM_MODE_CONNECTOR_DSI); 1977 1978 drm_connector_helper_add(connector, &intel_dsi_connector_helper_funcs); 1979 1980 connector->display_info.subpixel_order = SubPixelHorizontalRGB; /*XXX*/ 1981 connector->interlace_allowed = false; 1982 connector->doublescan_allowed = false; 1983 1984 intel_connector_attach_encoder(intel_connector, intel_encoder); 1985 1986 mutex_lock(&dev->mode_config.mutex); 1987 intel_panel_add_vbt_lfp_fixed_mode(intel_connector); 1988 mutex_unlock(&dev->mode_config.mutex); 1989 1990 if (!intel_panel_preferred_fixed_mode(intel_connector)) { 1991 drm_dbg_kms(&dev_priv->drm, "no fixed mode\n"); 1992 goto err_cleanup_connector; 1993 } 1994 1995 intel_panel_init(intel_connector); 1996 1997 intel_backlight_setup(intel_connector, INVALID_PIPE); 1998 1999 vlv_dsi_add_properties(intel_connector); 2000 2001 return; 2002 2003 err_cleanup_connector: 2004 drm_connector_cleanup(&intel_connector->base); 2005 err: 2006 drm_encoder_cleanup(&intel_encoder->base); 2007 kfree(intel_dsi); 2008 kfree(intel_connector); 2009 } 2010