1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * DesignWare MIPI DSI Host Controller v1.02 driver 4 * 5 * Copyright (c) 2016 Linaro Limited. 6 * Copyright (c) 2014-2016 HiSilicon Limited. 7 * 8 * Author: 9 * Xinliang Liu <z.liuxinliang@hisilicon.com> 10 * Xinliang Liu <xinliang.liu@linaro.org> 11 * Xinwei Kong <kong.kongxinwei@hisilicon.com> 12 */ 13 14 #include <linux/clk.h> 15 #include <linux/component.h> 16 #include <linux/delay.h> 17 #include <linux/module.h> 18 #include <linux/platform_device.h> 19 20 #include <drm/drm_atomic_helper.h> 21 #include <drm/drm_bridge.h> 22 #include <drm/drm_device.h> 23 #include <drm/drm_mipi_dsi.h> 24 #include <drm/drm_of.h> 25 #include <drm/drm_print.h> 26 #include <drm/drm_probe_helper.h> 27 #include <drm/drm_simple_kms_helper.h> 28 29 #include "dw_dsi_reg.h" 30 31 #define MAX_TX_ESC_CLK 10 32 #define ROUND(x, y) ((x) / (y) + \ 33 ((x) % (y) * 10 / (y) >= 5 ? 1 : 0)) 34 #define PHY_REF_CLK_RATE 19200000 35 #define PHY_REF_CLK_PERIOD_PS (1000000000 / (PHY_REF_CLK_RATE / 1000)) 36 37 #define encoder_to_dsi(encoder) \ 38 container_of(encoder, struct dw_dsi, encoder) 39 #define host_to_dsi(host) \ 40 container_of(host, struct dw_dsi, host) 41 42 struct mipi_phy_params { 43 u32 clk_t_lpx; 44 u32 clk_t_hs_prepare; 45 u32 clk_t_hs_zero; 46 u32 clk_t_hs_trial; 47 u32 clk_t_wakeup; 48 u32 data_t_lpx; 49 u32 data_t_hs_prepare; 50 u32 data_t_hs_zero; 51 u32 data_t_hs_trial; 52 u32 data_t_ta_go; 53 u32 data_t_ta_get; 54 u32 data_t_wakeup; 55 u32 hstx_ckg_sel; 56 u32 pll_fbd_div5f; 57 u32 pll_fbd_div1f; 58 u32 pll_fbd_2p; 59 u32 pll_enbwt; 60 u32 pll_fbd_p; 61 u32 pll_fbd_s; 62 u32 pll_pre_div1p; 63 u32 pll_pre_p; 64 u32 pll_vco_750M; 65 u32 pll_lpf_rs; 66 u32 pll_lpf_cs; 67 u32 clklp2hs_time; 68 u32 clkhs2lp_time; 69 u32 lp2hs_time; 70 u32 hs2lp_time; 71 u32 clk_to_data_delay; 72 u32 data_to_clk_delay; 73 u32 lane_byte_clk_kHz; 74 u32 clk_division; 75 }; 76 77 struct dsi_hw_ctx { 78 void __iomem *base; 79 struct clk *pclk; 80 }; 81 82 struct dw_dsi { 83 struct drm_encoder encoder; 84 struct drm_bridge *bridge; 85 struct mipi_dsi_host host; 86 struct drm_display_mode cur_mode; 87 struct dsi_hw_ctx *ctx; 88 struct mipi_phy_params phy; 89 90 u32 lanes; 91 enum mipi_dsi_pixel_format format; 92 unsigned long mode_flags; 93 bool enable; 94 }; 95 96 struct dsi_data { 97 struct dw_dsi dsi; 98 struct dsi_hw_ctx ctx; 99 }; 100 101 struct dsi_phy_range { 102 u32 min_range_kHz; 103 u32 max_range_kHz; 104 u32 pll_vco_750M; 105 u32 hstx_ckg_sel; 106 }; 107 108 static const struct dsi_phy_range dphy_range_info[] = { 109 { 46875, 62500, 1, 7 }, 110 { 62500, 93750, 0, 7 }, 111 { 93750, 125000, 1, 6 }, 112 { 125000, 187500, 0, 6 }, 113 { 187500, 250000, 1, 5 }, 114 { 250000, 375000, 0, 5 }, 115 { 375000, 500000, 1, 4 }, 116 { 500000, 750000, 0, 4 }, 117 { 750000, 1000000, 1, 0 }, 118 { 1000000, 1500000, 0, 0 } 119 }; 120 121 static u32 dsi_calc_phy_rate(u32 req_kHz, struct mipi_phy_params *phy) 122 { 123 u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS; 124 u32 tmp_kHz = req_kHz; 125 u32 i = 0; 126 u32 q_pll = 1; 127 u32 m_pll = 0; 128 u32 n_pll = 0; 129 u32 r_pll = 1; 130 u32 m_n = 0; 131 u32 m_n_int = 0; 132 u32 f_kHz = 0; 133 u64 temp; 134 135 /* 136 * Find a rate >= req_kHz. 137 */ 138 do { 139 f_kHz = tmp_kHz; 140 141 for (i = 0; i < ARRAY_SIZE(dphy_range_info); i++) 142 if (f_kHz >= dphy_range_info[i].min_range_kHz && 143 f_kHz <= dphy_range_info[i].max_range_kHz) 144 break; 145 146 if (i == ARRAY_SIZE(dphy_range_info)) { 147 DRM_ERROR("%dkHz out of range\n", f_kHz); 148 return 0; 149 } 150 151 phy->pll_vco_750M = dphy_range_info[i].pll_vco_750M; 152 phy->hstx_ckg_sel = dphy_range_info[i].hstx_ckg_sel; 153 154 if (phy->hstx_ckg_sel <= 7 && 155 phy->hstx_ckg_sel >= 4) 156 q_pll = 0x10 >> (7 - phy->hstx_ckg_sel); 157 158 temp = f_kHz * (u64)q_pll * (u64)ref_clk_ps; 159 m_n_int = temp / (u64)1000000000; 160 m_n = (temp % (u64)1000000000) / (u64)100000000; 161 162 if (m_n_int % 2 == 0) { 163 if (m_n * 6 >= 50) { 164 n_pll = 2; 165 m_pll = (m_n_int + 1) * n_pll; 166 } else if (m_n * 6 >= 30) { 167 n_pll = 3; 168 m_pll = m_n_int * n_pll + 2; 169 } else { 170 n_pll = 1; 171 m_pll = m_n_int * n_pll; 172 } 173 } else { 174 if (m_n * 6 >= 50) { 175 n_pll = 1; 176 m_pll = (m_n_int + 1) * n_pll; 177 } else if (m_n * 6 >= 30) { 178 n_pll = 1; 179 m_pll = (m_n_int + 1) * n_pll; 180 } else if (m_n * 6 >= 10) { 181 n_pll = 3; 182 m_pll = m_n_int * n_pll + 1; 183 } else { 184 n_pll = 2; 185 m_pll = m_n_int * n_pll; 186 } 187 } 188 189 if (n_pll == 1) { 190 phy->pll_fbd_p = 0; 191 phy->pll_pre_div1p = 1; 192 } else { 193 phy->pll_fbd_p = n_pll; 194 phy->pll_pre_div1p = 0; 195 } 196 197 if (phy->pll_fbd_2p <= 7 && phy->pll_fbd_2p >= 4) 198 r_pll = 0x10 >> (7 - phy->pll_fbd_2p); 199 200 if (m_pll == 2) { 201 phy->pll_pre_p = 0; 202 phy->pll_fbd_s = 0; 203 phy->pll_fbd_div1f = 0; 204 phy->pll_fbd_div5f = 1; 205 } else if (m_pll >= 2 * 2 * r_pll && m_pll <= 2 * 4 * r_pll) { 206 phy->pll_pre_p = m_pll / (2 * r_pll); 207 phy->pll_fbd_s = 0; 208 phy->pll_fbd_div1f = 1; 209 phy->pll_fbd_div5f = 0; 210 } else if (m_pll >= 2 * 5 * r_pll && m_pll <= 2 * 150 * r_pll) { 211 if (((m_pll / (2 * r_pll)) % 2) == 0) { 212 phy->pll_pre_p = 213 (m_pll / (2 * r_pll)) / 2 - 1; 214 phy->pll_fbd_s = 215 (m_pll / (2 * r_pll)) % 2 + 2; 216 } else { 217 phy->pll_pre_p = 218 (m_pll / (2 * r_pll)) / 2; 219 phy->pll_fbd_s = 220 (m_pll / (2 * r_pll)) % 2; 221 } 222 phy->pll_fbd_div1f = 0; 223 phy->pll_fbd_div5f = 0; 224 } else { 225 phy->pll_pre_p = 0; 226 phy->pll_fbd_s = 0; 227 phy->pll_fbd_div1f = 0; 228 phy->pll_fbd_div5f = 1; 229 } 230 231 f_kHz = (u64)1000000000 * (u64)m_pll / 232 ((u64)ref_clk_ps * (u64)n_pll * (u64)q_pll); 233 234 if (f_kHz >= req_kHz) 235 break; 236 237 tmp_kHz += 10; 238 239 } while (true); 240 241 return f_kHz; 242 } 243 244 static void dsi_get_phy_params(u32 phy_req_kHz, 245 struct mipi_phy_params *phy) 246 { 247 u32 ref_clk_ps = PHY_REF_CLK_PERIOD_PS; 248 u32 phy_rate_kHz; 249 u32 ui; 250 251 memset(phy, 0, sizeof(*phy)); 252 253 phy_rate_kHz = dsi_calc_phy_rate(phy_req_kHz, phy); 254 if (!phy_rate_kHz) 255 return; 256 257 ui = 1000000 / phy_rate_kHz; 258 259 phy->clk_t_lpx = ROUND(50, 8 * ui); 260 phy->clk_t_hs_prepare = ROUND(133, 16 * ui) - 1; 261 262 phy->clk_t_hs_zero = ROUND(262, 8 * ui); 263 phy->clk_t_hs_trial = 2 * (ROUND(60, 8 * ui) - 1); 264 phy->clk_t_wakeup = ROUND(1000000, (ref_clk_ps / 1000) - 1); 265 if (phy->clk_t_wakeup > 0xff) 266 phy->clk_t_wakeup = 0xff; 267 phy->data_t_wakeup = phy->clk_t_wakeup; 268 phy->data_t_lpx = phy->clk_t_lpx; 269 phy->data_t_hs_prepare = ROUND(125 + 10 * ui, 16 * ui) - 1; 270 phy->data_t_hs_zero = ROUND(105 + 6 * ui, 8 * ui); 271 phy->data_t_hs_trial = 2 * (ROUND(60 + 4 * ui, 8 * ui) - 1); 272 phy->data_t_ta_go = 3; 273 phy->data_t_ta_get = 4; 274 275 phy->pll_enbwt = 1; 276 phy->clklp2hs_time = ROUND(407, 8 * ui) + 12; 277 phy->clkhs2lp_time = ROUND(105 + 12 * ui, 8 * ui); 278 phy->lp2hs_time = ROUND(240 + 12 * ui, 8 * ui) + 1; 279 phy->hs2lp_time = phy->clkhs2lp_time; 280 phy->clk_to_data_delay = 1 + phy->clklp2hs_time; 281 phy->data_to_clk_delay = ROUND(60 + 52 * ui, 8 * ui) + 282 phy->clkhs2lp_time; 283 284 phy->lane_byte_clk_kHz = phy_rate_kHz / 8; 285 phy->clk_division = 286 DIV_ROUND_UP(phy->lane_byte_clk_kHz, MAX_TX_ESC_CLK); 287 } 288 289 static u32 dsi_get_dpi_color_coding(enum mipi_dsi_pixel_format format) 290 { 291 u32 val; 292 293 /* 294 * TODO: only support RGB888 now, to support more 295 */ 296 switch (format) { 297 case MIPI_DSI_FMT_RGB888: 298 val = DSI_24BITS_1; 299 break; 300 default: 301 val = DSI_24BITS_1; 302 break; 303 } 304 305 return val; 306 } 307 308 /* 309 * dsi phy reg write function 310 */ 311 static void dsi_phy_tst_set(void __iomem *base, u32 reg, u32 val) 312 { 313 u32 reg_write = 0x10000 + reg; 314 315 /* 316 * latch reg first 317 */ 318 writel(reg_write, base + PHY_TST_CTRL1); 319 writel(0x02, base + PHY_TST_CTRL0); 320 writel(0x00, base + PHY_TST_CTRL0); 321 322 /* 323 * then latch value 324 */ 325 writel(val, base + PHY_TST_CTRL1); 326 writel(0x02, base + PHY_TST_CTRL0); 327 writel(0x00, base + PHY_TST_CTRL0); 328 } 329 330 static void dsi_set_phy_timer(void __iomem *base, 331 struct mipi_phy_params *phy, 332 u32 lanes) 333 { 334 u32 val; 335 336 /* 337 * Set lane value and phy stop wait time. 338 */ 339 val = (lanes - 1) | (PHY_STOP_WAIT_TIME << 8); 340 writel(val, base + PHY_IF_CFG); 341 342 /* 343 * Set phy clk division. 344 */ 345 val = readl(base + CLKMGR_CFG) | phy->clk_division; 346 writel(val, base + CLKMGR_CFG); 347 348 /* 349 * Set lp and hs switching params. 350 */ 351 dw_update_bits(base + PHY_TMR_CFG, 24, MASK(8), phy->hs2lp_time); 352 dw_update_bits(base + PHY_TMR_CFG, 16, MASK(8), phy->lp2hs_time); 353 dw_update_bits(base + PHY_TMR_LPCLK_CFG, 16, MASK(10), 354 phy->clkhs2lp_time); 355 dw_update_bits(base + PHY_TMR_LPCLK_CFG, 0, MASK(10), 356 phy->clklp2hs_time); 357 dw_update_bits(base + CLK_DATA_TMR_CFG, 8, MASK(8), 358 phy->data_to_clk_delay); 359 dw_update_bits(base + CLK_DATA_TMR_CFG, 0, MASK(8), 360 phy->clk_to_data_delay); 361 } 362 363 static void dsi_set_mipi_phy(void __iomem *base, 364 struct mipi_phy_params *phy, 365 u32 lanes) 366 { 367 u32 delay_count; 368 u32 val; 369 u32 i; 370 371 /* phy timer setting */ 372 dsi_set_phy_timer(base, phy, lanes); 373 374 /* 375 * Reset to clean up phy tst params. 376 */ 377 writel(0, base + PHY_RSTZ); 378 writel(0, base + PHY_TST_CTRL0); 379 writel(1, base + PHY_TST_CTRL0); 380 writel(0, base + PHY_TST_CTRL0); 381 382 /* 383 * Clock lane timing control setting: TLPX, THS-PREPARE, 384 * THS-ZERO, THS-TRAIL, TWAKEUP. 385 */ 386 dsi_phy_tst_set(base, CLK_TLPX, phy->clk_t_lpx); 387 dsi_phy_tst_set(base, CLK_THS_PREPARE, phy->clk_t_hs_prepare); 388 dsi_phy_tst_set(base, CLK_THS_ZERO, phy->clk_t_hs_zero); 389 dsi_phy_tst_set(base, CLK_THS_TRAIL, phy->clk_t_hs_trial); 390 dsi_phy_tst_set(base, CLK_TWAKEUP, phy->clk_t_wakeup); 391 392 /* 393 * Data lane timing control setting: TLPX, THS-PREPARE, 394 * THS-ZERO, THS-TRAIL, TTA-GO, TTA-GET, TWAKEUP. 395 */ 396 for (i = 0; i < lanes; i++) { 397 dsi_phy_tst_set(base, DATA_TLPX(i), phy->data_t_lpx); 398 dsi_phy_tst_set(base, DATA_THS_PREPARE(i), 399 phy->data_t_hs_prepare); 400 dsi_phy_tst_set(base, DATA_THS_ZERO(i), phy->data_t_hs_zero); 401 dsi_phy_tst_set(base, DATA_THS_TRAIL(i), phy->data_t_hs_trial); 402 dsi_phy_tst_set(base, DATA_TTA_GO(i), phy->data_t_ta_go); 403 dsi_phy_tst_set(base, DATA_TTA_GET(i), phy->data_t_ta_get); 404 dsi_phy_tst_set(base, DATA_TWAKEUP(i), phy->data_t_wakeup); 405 } 406 407 /* 408 * physical configuration: I, pll I, pll II, pll III, 409 * pll IV, pll V. 410 */ 411 dsi_phy_tst_set(base, PHY_CFG_I, phy->hstx_ckg_sel); 412 val = (phy->pll_fbd_div5f << 5) + (phy->pll_fbd_div1f << 4) + 413 (phy->pll_fbd_2p << 1) + phy->pll_enbwt; 414 dsi_phy_tst_set(base, PHY_CFG_PLL_I, val); 415 dsi_phy_tst_set(base, PHY_CFG_PLL_II, phy->pll_fbd_p); 416 dsi_phy_tst_set(base, PHY_CFG_PLL_III, phy->pll_fbd_s); 417 val = (phy->pll_pre_div1p << 7) + phy->pll_pre_p; 418 dsi_phy_tst_set(base, PHY_CFG_PLL_IV, val); 419 val = (5 << 5) + (phy->pll_vco_750M << 4) + (phy->pll_lpf_rs << 2) + 420 phy->pll_lpf_cs; 421 dsi_phy_tst_set(base, PHY_CFG_PLL_V, val); 422 423 writel(PHY_ENABLECLK, base + PHY_RSTZ); 424 udelay(1); 425 writel(PHY_ENABLECLK | PHY_UNSHUTDOWNZ, base + PHY_RSTZ); 426 udelay(1); 427 writel(PHY_ENABLECLK | PHY_UNRSTZ | PHY_UNSHUTDOWNZ, base + PHY_RSTZ); 428 usleep_range(1000, 1500); 429 430 /* 431 * wait for phy's clock ready 432 */ 433 delay_count = 100; 434 while (delay_count) { 435 val = readl(base + PHY_STATUS); 436 if ((BIT(0) | BIT(2)) & val) 437 break; 438 439 udelay(1); 440 delay_count--; 441 } 442 443 if (!delay_count) 444 DRM_INFO("phylock and phystopstateclklane is not ready.\n"); 445 } 446 447 static void dsi_set_mode_timing(void __iomem *base, 448 u32 lane_byte_clk_kHz, 449 struct drm_display_mode *mode, 450 enum mipi_dsi_pixel_format format) 451 { 452 u32 hfp, hbp, hsw, vfp, vbp, vsw; 453 u32 hline_time; 454 u32 hsa_time; 455 u32 hbp_time; 456 u32 pixel_clk_kHz; 457 int htot, vtot; 458 u32 val; 459 u64 tmp; 460 461 val = dsi_get_dpi_color_coding(format); 462 writel(val, base + DPI_COLOR_CODING); 463 464 val = (mode->flags & DRM_MODE_FLAG_NHSYNC ? 1 : 0) << 2; 465 val |= (mode->flags & DRM_MODE_FLAG_NVSYNC ? 1 : 0) << 1; 466 writel(val, base + DPI_CFG_POL); 467 468 /* 469 * The DSI IP accepts vertical timing using lines as normal, 470 * but horizontal timing is a mixture of pixel-clocks for the 471 * active region and byte-lane clocks for the blanking-related 472 * timings. hfp is specified as the total hline_time in byte- 473 * lane clocks minus hsa, hbp and active. 474 */ 475 pixel_clk_kHz = mode->clock; 476 htot = mode->htotal; 477 vtot = mode->vtotal; 478 hfp = mode->hsync_start - mode->hdisplay; 479 hbp = mode->htotal - mode->hsync_end; 480 hsw = mode->hsync_end - mode->hsync_start; 481 vfp = mode->vsync_start - mode->vdisplay; 482 vbp = mode->vtotal - mode->vsync_end; 483 vsw = mode->vsync_end - mode->vsync_start; 484 if (vsw > 15) { 485 DRM_DEBUG_DRIVER("vsw exceeded 15\n"); 486 vsw = 15; 487 } 488 489 hsa_time = (hsw * lane_byte_clk_kHz) / pixel_clk_kHz; 490 hbp_time = (hbp * lane_byte_clk_kHz) / pixel_clk_kHz; 491 tmp = (u64)htot * (u64)lane_byte_clk_kHz; 492 hline_time = DIV_ROUND_UP(tmp, pixel_clk_kHz); 493 494 /* all specified in byte-lane clocks */ 495 writel(hsa_time, base + VID_HSA_TIME); 496 writel(hbp_time, base + VID_HBP_TIME); 497 writel(hline_time, base + VID_HLINE_TIME); 498 499 writel(vsw, base + VID_VSA_LINES); 500 writel(vbp, base + VID_VBP_LINES); 501 writel(vfp, base + VID_VFP_LINES); 502 writel(mode->vdisplay, base + VID_VACTIVE_LINES); 503 writel(mode->hdisplay, base + VID_PKT_SIZE); 504 505 DRM_DEBUG_DRIVER("htot=%d, hfp=%d, hbp=%d, hsw=%d\n", 506 htot, hfp, hbp, hsw); 507 DRM_DEBUG_DRIVER("vtol=%d, vfp=%d, vbp=%d, vsw=%d\n", 508 vtot, vfp, vbp, vsw); 509 DRM_DEBUG_DRIVER("hsa_time=%d, hbp_time=%d, hline_time=%d\n", 510 hsa_time, hbp_time, hline_time); 511 } 512 513 static void dsi_set_video_mode(void __iomem *base, unsigned long flags) 514 { 515 u32 val; 516 u32 mode_mask = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | 517 MIPI_DSI_MODE_VIDEO_SYNC_PULSE; 518 u32 non_burst_sync_pulse = MIPI_DSI_MODE_VIDEO | 519 MIPI_DSI_MODE_VIDEO_SYNC_PULSE; 520 u32 non_burst_sync_event = MIPI_DSI_MODE_VIDEO; 521 522 /* 523 * choose video mode type 524 */ 525 if ((flags & mode_mask) == non_burst_sync_pulse) 526 val = DSI_NON_BURST_SYNC_PULSES; 527 else if ((flags & mode_mask) == non_burst_sync_event) 528 val = DSI_NON_BURST_SYNC_EVENTS; 529 else 530 val = DSI_BURST_SYNC_PULSES_1; 531 writel(val, base + VID_MODE_CFG); 532 533 writel(PHY_TXREQUESTCLKHS, base + LPCLK_CTRL); 534 writel(DSI_VIDEO_MODE, base + MODE_CFG); 535 } 536 537 static void dsi_mipi_init(struct dw_dsi *dsi) 538 { 539 struct dsi_hw_ctx *ctx = dsi->ctx; 540 struct mipi_phy_params *phy = &dsi->phy; 541 struct drm_display_mode *mode = &dsi->cur_mode; 542 u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); 543 void __iomem *base = ctx->base; 544 u32 dphy_req_kHz; 545 546 /* 547 * count phy params 548 */ 549 dphy_req_kHz = mode->clock * bpp / dsi->lanes; 550 dsi_get_phy_params(dphy_req_kHz, phy); 551 552 /* reset Core */ 553 writel(RESET, base + PWR_UP); 554 555 /* set dsi phy params */ 556 dsi_set_mipi_phy(base, phy, dsi->lanes); 557 558 /* set dsi mode timing */ 559 dsi_set_mode_timing(base, phy->lane_byte_clk_kHz, mode, dsi->format); 560 561 /* set dsi video mode */ 562 dsi_set_video_mode(base, dsi->mode_flags); 563 564 /* dsi wake up */ 565 writel(POWERUP, base + PWR_UP); 566 567 DRM_DEBUG_DRIVER("lanes=%d, pixel_clk=%d kHz, bytes_freq=%d kHz\n", 568 dsi->lanes, mode->clock, phy->lane_byte_clk_kHz); 569 } 570 571 static void dsi_encoder_disable(struct drm_encoder *encoder) 572 { 573 struct dw_dsi *dsi = encoder_to_dsi(encoder); 574 struct dsi_hw_ctx *ctx = dsi->ctx; 575 void __iomem *base = ctx->base; 576 577 if (!dsi->enable) 578 return; 579 580 writel(0, base + PWR_UP); 581 writel(0, base + LPCLK_CTRL); 582 writel(0, base + PHY_RSTZ); 583 clk_disable_unprepare(ctx->pclk); 584 585 dsi->enable = false; 586 } 587 588 static void dsi_encoder_enable(struct drm_encoder *encoder) 589 { 590 struct dw_dsi *dsi = encoder_to_dsi(encoder); 591 struct dsi_hw_ctx *ctx = dsi->ctx; 592 int ret; 593 594 if (dsi->enable) 595 return; 596 597 ret = clk_prepare_enable(ctx->pclk); 598 if (ret) { 599 DRM_ERROR("fail to enable pclk: %d\n", ret); 600 return; 601 } 602 603 dsi_mipi_init(dsi); 604 605 dsi->enable = true; 606 } 607 608 static enum drm_mode_status dsi_encoder_phy_mode_valid( 609 struct drm_encoder *encoder, 610 const struct drm_display_mode *mode) 611 { 612 struct dw_dsi *dsi = encoder_to_dsi(encoder); 613 struct mipi_phy_params phy; 614 u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); 615 u32 req_kHz, act_kHz, lane_byte_clk_kHz; 616 617 /* Calculate the lane byte clk using the adjusted mode clk */ 618 memset(&phy, 0, sizeof(phy)); 619 req_kHz = mode->clock * bpp / dsi->lanes; 620 act_kHz = dsi_calc_phy_rate(req_kHz, &phy); 621 lane_byte_clk_kHz = act_kHz / 8; 622 623 DRM_DEBUG_DRIVER("Checking mode %ix%i-%i@%i clock: %i...", 624 mode->hdisplay, mode->vdisplay, bpp, 625 drm_mode_vrefresh(mode), mode->clock); 626 627 /* 628 * Make sure the adjusted mode clock and the lane byte clk 629 * have a common denominator base frequency 630 */ 631 if (mode->clock/dsi->lanes == lane_byte_clk_kHz/3) { 632 DRM_DEBUG_DRIVER("OK!\n"); 633 return MODE_OK; 634 } 635 636 DRM_DEBUG_DRIVER("BAD!\n"); 637 return MODE_BAD; 638 } 639 640 static enum drm_mode_status dsi_encoder_mode_valid(struct drm_encoder *encoder, 641 const struct drm_display_mode *mode) 642 643 { 644 const struct drm_crtc_helper_funcs *crtc_funcs = NULL; 645 struct drm_crtc *crtc = NULL; 646 struct drm_display_mode adj_mode; 647 enum drm_mode_status ret; 648 649 /* 650 * The crtc might adjust the mode, so go through the 651 * possible crtcs (technically just one) and call 652 * mode_fixup to figure out the adjusted mode before we 653 * validate it. 654 */ 655 drm_for_each_crtc(crtc, encoder->dev) { 656 /* 657 * reset adj_mode to the mode value each time, 658 * so we don't adjust the mode twice 659 */ 660 drm_mode_copy(&adj_mode, mode); 661 662 crtc_funcs = crtc->helper_private; 663 if (crtc_funcs && crtc_funcs->mode_fixup) 664 if (!crtc_funcs->mode_fixup(crtc, mode, &adj_mode)) 665 return MODE_BAD; 666 667 ret = dsi_encoder_phy_mode_valid(encoder, &adj_mode); 668 if (ret != MODE_OK) 669 return ret; 670 } 671 return MODE_OK; 672 } 673 674 static void dsi_encoder_mode_set(struct drm_encoder *encoder, 675 struct drm_display_mode *mode, 676 struct drm_display_mode *adj_mode) 677 { 678 struct dw_dsi *dsi = encoder_to_dsi(encoder); 679 680 drm_mode_copy(&dsi->cur_mode, adj_mode); 681 } 682 683 static int dsi_encoder_atomic_check(struct drm_encoder *encoder, 684 struct drm_crtc_state *crtc_state, 685 struct drm_connector_state *conn_state) 686 { 687 /* do nothing */ 688 return 0; 689 } 690 691 static const struct drm_encoder_helper_funcs dw_encoder_helper_funcs = { 692 .atomic_check = dsi_encoder_atomic_check, 693 .mode_valid = dsi_encoder_mode_valid, 694 .mode_set = dsi_encoder_mode_set, 695 .enable = dsi_encoder_enable, 696 .disable = dsi_encoder_disable 697 }; 698 699 static int dw_drm_encoder_init(struct device *dev, 700 struct drm_device *drm_dev, 701 struct drm_encoder *encoder) 702 { 703 int ret; 704 u32 crtc_mask = drm_of_find_possible_crtcs(drm_dev, dev->of_node); 705 706 if (!crtc_mask) { 707 DRM_ERROR("failed to find crtc mask\n"); 708 return -EINVAL; 709 } 710 711 encoder->possible_crtcs = crtc_mask; 712 ret = drm_simple_encoder_init(drm_dev, encoder, DRM_MODE_ENCODER_DSI); 713 if (ret) { 714 DRM_ERROR("failed to init dsi encoder\n"); 715 return ret; 716 } 717 718 drm_encoder_helper_add(encoder, &dw_encoder_helper_funcs); 719 720 return 0; 721 } 722 723 static int dsi_host_attach(struct mipi_dsi_host *host, 724 struct mipi_dsi_device *mdsi) 725 { 726 struct dw_dsi *dsi = host_to_dsi(host); 727 728 if (mdsi->lanes < 1 || mdsi->lanes > 4) { 729 DRM_ERROR("dsi device params invalid\n"); 730 return -EINVAL; 731 } 732 733 dsi->lanes = mdsi->lanes; 734 dsi->format = mdsi->format; 735 dsi->mode_flags = mdsi->mode_flags; 736 737 return 0; 738 } 739 740 static int dsi_host_detach(struct mipi_dsi_host *host, 741 struct mipi_dsi_device *mdsi) 742 { 743 /* do nothing */ 744 return 0; 745 } 746 747 static const struct mipi_dsi_host_ops dsi_host_ops = { 748 .attach = dsi_host_attach, 749 .detach = dsi_host_detach, 750 }; 751 752 static int dsi_host_init(struct device *dev, struct dw_dsi *dsi) 753 { 754 struct mipi_dsi_host *host = &dsi->host; 755 int ret; 756 757 host->dev = dev; 758 host->ops = &dsi_host_ops; 759 ret = mipi_dsi_host_register(host); 760 if (ret) { 761 DRM_ERROR("failed to register dsi host\n"); 762 return ret; 763 } 764 765 return 0; 766 } 767 768 static int dsi_bridge_init(struct drm_device *dev, struct dw_dsi *dsi) 769 { 770 struct drm_encoder *encoder = &dsi->encoder; 771 struct drm_bridge *bridge = dsi->bridge; 772 773 /* associate the bridge to dsi encoder */ 774 return drm_bridge_attach(encoder, bridge, NULL, 0); 775 } 776 777 static int dsi_bind(struct device *dev, struct device *master, void *data) 778 { 779 struct dsi_data *ddata = dev_get_drvdata(dev); 780 struct dw_dsi *dsi = &ddata->dsi; 781 struct drm_device *drm_dev = data; 782 int ret; 783 784 ret = dw_drm_encoder_init(dev, drm_dev, &dsi->encoder); 785 if (ret) 786 return ret; 787 788 ret = dsi_host_init(dev, dsi); 789 if (ret) 790 return ret; 791 792 ret = dsi_bridge_init(drm_dev, dsi); 793 if (ret) 794 return ret; 795 796 return 0; 797 } 798 799 static void dsi_unbind(struct device *dev, struct device *master, void *data) 800 { 801 /* do nothing */ 802 } 803 804 static const struct component_ops dsi_ops = { 805 .bind = dsi_bind, 806 .unbind = dsi_unbind, 807 }; 808 809 static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi) 810 { 811 struct dsi_hw_ctx *ctx = dsi->ctx; 812 struct device_node *np = pdev->dev.of_node; 813 struct resource *res; 814 int ret; 815 816 /* 817 * Get the endpoint node. In our case, dsi has one output port1 818 * to which the external HDMI bridge is connected. 819 */ 820 ret = drm_of_find_panel_or_bridge(np, 1, 0, NULL, &dsi->bridge); 821 if (ret) 822 return ret; 823 824 ctx->pclk = devm_clk_get(&pdev->dev, "pclk"); 825 if (IS_ERR(ctx->pclk)) { 826 DRM_ERROR("failed to get pclk clock\n"); 827 return PTR_ERR(ctx->pclk); 828 } 829 830 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 831 ctx->base = devm_ioremap_resource(&pdev->dev, res); 832 if (IS_ERR(ctx->base)) { 833 DRM_ERROR("failed to remap dsi io region\n"); 834 return PTR_ERR(ctx->base); 835 } 836 837 return 0; 838 } 839 840 static int dsi_probe(struct platform_device *pdev) 841 { 842 struct dsi_data *data; 843 struct dw_dsi *dsi; 844 struct dsi_hw_ctx *ctx; 845 int ret; 846 847 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); 848 if (!data) { 849 DRM_ERROR("failed to allocate dsi data.\n"); 850 return -ENOMEM; 851 } 852 dsi = &data->dsi; 853 ctx = &data->ctx; 854 dsi->ctx = ctx; 855 856 ret = dsi_parse_dt(pdev, dsi); 857 if (ret) 858 return ret; 859 860 platform_set_drvdata(pdev, data); 861 862 return component_add(&pdev->dev, &dsi_ops); 863 } 864 865 static int dsi_remove(struct platform_device *pdev) 866 { 867 component_del(&pdev->dev, &dsi_ops); 868 869 return 0; 870 } 871 872 static const struct of_device_id dsi_of_match[] = { 873 {.compatible = "hisilicon,hi6220-dsi"}, 874 { } 875 }; 876 MODULE_DEVICE_TABLE(of, dsi_of_match); 877 878 static struct platform_driver dsi_driver = { 879 .probe = dsi_probe, 880 .remove = dsi_remove, 881 .driver = { 882 .name = "dw-dsi", 883 .of_match_table = dsi_of_match, 884 }, 885 }; 886 887 module_platform_driver(dsi_driver); 888 889 MODULE_AUTHOR("Xinliang Liu <xinliang.liu@linaro.org>"); 890 MODULE_AUTHOR("Xinliang Liu <z.liuxinliang@hisilicon.com>"); 891 MODULE_AUTHOR("Xinwei Kong <kong.kongxinwei@hisilicon.com>"); 892 MODULE_DESCRIPTION("DesignWare MIPI DSI Host Controller v1.02 driver"); 893 MODULE_LICENSE("GPL v2"); 894