1 /* 2 * tc358767 eDP bridge driver 3 * 4 * Copyright (C) 2016 CogentEmbedded Inc 5 * Author: Andrey Gusakov <andrey.gusakov@cogentembedded.com> 6 * 7 * Copyright (C) 2016 Pengutronix, Philipp Zabel <p.zabel@pengutronix.de> 8 * 9 * Initially based on: drivers/gpu/drm/i2c/tda998x_drv.c 10 * 11 * Copyright (C) 2012 Texas Instruments 12 * Author: Rob Clark <robdclark@gmail.com> 13 * 14 * This program is free software; you can redistribute it and/or modify 15 * it under the terms of the GNU General Public License as published by 16 * the Free Software Foundation; either version 2 of the License, or 17 * (at your option) any later version. 18 * 19 * This program is distributed in the hope that it will be useful, 20 * but WITHOUT ANY WARRANTY; without even the implied warranty of 21 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 22 * GNU General Public License for more details. 23 */ 24 25 #include <linux/clk.h> 26 #include <linux/device.h> 27 #include <linux/gpio/consumer.h> 28 #include <linux/i2c.h> 29 #include <linux/kernel.h> 30 #include <linux/module.h> 31 #include <linux/regmap.h> 32 #include <linux/slab.h> 33 34 #include <drm/drm_atomic_helper.h> 35 #include <drm/drm_crtc_helper.h> 36 #include <drm/drm_dp_helper.h> 37 #include <drm/drm_edid.h> 38 #include <drm/drm_of.h> 39 #include <drm/drm_panel.h> 40 41 /* Registers */ 42 43 /* Display Parallel Interface */ 44 #define DPIPXLFMT 0x0440 45 #define VS_POL_ACTIVE_LOW (1 << 10) 46 #define HS_POL_ACTIVE_LOW (1 << 9) 47 #define DE_POL_ACTIVE_HIGH (0 << 8) 48 #define SUB_CFG_TYPE_CONFIG1 (0 << 2) /* LSB aligned */ 49 #define SUB_CFG_TYPE_CONFIG2 (1 << 2) /* Loosely Packed */ 50 #define SUB_CFG_TYPE_CONFIG3 (2 << 2) /* LSB aligned 8-bit */ 51 #define DPI_BPP_RGB888 (0 << 0) 52 #define DPI_BPP_RGB666 (1 << 0) 53 #define DPI_BPP_RGB565 (2 << 0) 54 55 /* Video Path */ 56 #define VPCTRL0 0x0450 57 #define OPXLFMT_RGB666 (0 << 8) 58 #define OPXLFMT_RGB888 (1 << 8) 59 #define FRMSYNC_DISABLED (0 << 4) /* Video Timing Gen Disabled */ 60 #define FRMSYNC_ENABLED (1 << 4) /* Video Timing Gen Enabled */ 61 #define MSF_DISABLED (0 << 0) /* Magic Square FRC disabled */ 62 #define MSF_ENABLED (1 << 0) /* Magic Square FRC enabled */ 63 #define HTIM01 0x0454 64 #define HTIM02 0x0458 65 #define VTIM01 0x045c 66 #define VTIM02 0x0460 67 #define VFUEN0 0x0464 68 #define VFUEN BIT(0) /* Video Frame Timing Upload */ 69 70 /* System */ 71 #define TC_IDREG 0x0500 72 #define SYSCTRL 0x0510 73 #define DP0_AUDSRC_NO_INPUT (0 << 3) 74 #define DP0_AUDSRC_I2S_RX (1 << 3) 75 #define DP0_VIDSRC_NO_INPUT (0 << 0) 76 #define DP0_VIDSRC_DSI_RX (1 << 0) 77 #define DP0_VIDSRC_DPI_RX (2 << 0) 78 #define DP0_VIDSRC_COLOR_BAR (3 << 0) 79 80 /* Control */ 81 #define DP0CTL 0x0600 82 #define VID_MN_GEN BIT(6) /* Auto-generate M/N values */ 83 #define EF_EN BIT(5) /* Enable Enhanced Framing */ 84 #define VID_EN BIT(1) /* Video transmission enable */ 85 #define DP_EN BIT(0) /* Enable DPTX function */ 86 87 /* Clocks */ 88 #define DP0_VIDMNGEN0 0x0610 89 #define DP0_VIDMNGEN1 0x0614 90 #define DP0_VMNGENSTATUS 0x0618 91 92 /* Main Channel */ 93 #define DP0_SECSAMPLE 0x0640 94 #define DP0_VIDSYNCDELAY 0x0644 95 #define DP0_TOTALVAL 0x0648 96 #define DP0_STARTVAL 0x064c 97 #define DP0_ACTIVEVAL 0x0650 98 #define DP0_SYNCVAL 0x0654 99 #define DP0_MISC 0x0658 100 #define TU_SIZE_RECOMMENDED (0x3f << 16) /* LSCLK cycles per TU */ 101 #define BPC_6 (0 << 5) 102 #define BPC_8 (1 << 5) 103 104 /* AUX channel */ 105 #define DP0_AUXCFG0 0x0660 106 #define DP0_AUXCFG1 0x0664 107 #define AUX_RX_FILTER_EN BIT(16) 108 109 #define DP0_AUXADDR 0x0668 110 #define DP0_AUXWDATA(i) (0x066c + (i) * 4) 111 #define DP0_AUXRDATA(i) (0x067c + (i) * 4) 112 #define DP0_AUXSTATUS 0x068c 113 #define AUX_STATUS_MASK 0xf0 114 #define AUX_STATUS_SHIFT 4 115 #define AUX_TIMEOUT BIT(1) 116 #define AUX_BUSY BIT(0) 117 #define DP0_AUXI2CADR 0x0698 118 119 /* Link Training */ 120 #define DP0_SRCCTRL 0x06a0 121 #define DP0_SRCCTRL_SCRMBLDIS BIT(13) 122 #define DP0_SRCCTRL_EN810B BIT(12) 123 #define DP0_SRCCTRL_NOTP (0 << 8) 124 #define DP0_SRCCTRL_TP1 (1 << 8) 125 #define DP0_SRCCTRL_TP2 (2 << 8) 126 #define DP0_SRCCTRL_LANESKEW BIT(7) 127 #define DP0_SRCCTRL_SSCG BIT(3) 128 #define DP0_SRCCTRL_LANES_1 (0 << 2) 129 #define DP0_SRCCTRL_LANES_2 (1 << 2) 130 #define DP0_SRCCTRL_BW27 (1 << 1) 131 #define DP0_SRCCTRL_BW162 (0 << 1) 132 #define DP0_SRCCTRL_AUTOCORRECT BIT(0) 133 #define DP0_LTSTAT 0x06d0 134 #define LT_LOOPDONE BIT(13) 135 #define LT_STATUS_MASK (0x1f << 8) 136 #define LT_CHANNEL1_EQ_BITS (DP_CHANNEL_EQ_BITS << 4) 137 #define LT_INTERLANE_ALIGN_DONE BIT(3) 138 #define LT_CHANNEL0_EQ_BITS (DP_CHANNEL_EQ_BITS) 139 #define DP0_SNKLTCHGREQ 0x06d4 140 #define DP0_LTLOOPCTRL 0x06d8 141 #define DP0_SNKLTCTRL 0x06e4 142 143 /* PHY */ 144 #define DP_PHY_CTRL 0x0800 145 #define DP_PHY_RST BIT(28) /* DP PHY Global Soft Reset */ 146 #define BGREN BIT(25) /* AUX PHY BGR Enable */ 147 #define PWR_SW_EN BIT(24) /* PHY Power Switch Enable */ 148 #define PHY_M1_RST BIT(12) /* Reset PHY1 Main Channel */ 149 #define PHY_RDY BIT(16) /* PHY Main Channels Ready */ 150 #define PHY_M0_RST BIT(8) /* Reset PHY0 Main Channel */ 151 #define PHY_A0_EN BIT(1) /* PHY Aux Channel0 Enable */ 152 #define PHY_M0_EN BIT(0) /* PHY Main Channel0 Enable */ 153 154 /* PLL */ 155 #define DP0_PLLCTRL 0x0900 156 #define DP1_PLLCTRL 0x0904 /* not defined in DS */ 157 #define PXL_PLLCTRL 0x0908 158 #define PLLUPDATE BIT(2) 159 #define PLLBYP BIT(1) 160 #define PLLEN BIT(0) 161 #define PXL_PLLPARAM 0x0914 162 #define IN_SEL_REFCLK (0 << 14) 163 #define SYS_PLLPARAM 0x0918 164 #define REF_FREQ_38M4 (0 << 8) /* 38.4 MHz */ 165 #define REF_FREQ_19M2 (1 << 8) /* 19.2 MHz */ 166 #define REF_FREQ_26M (2 << 8) /* 26 MHz */ 167 #define REF_FREQ_13M (3 << 8) /* 13 MHz */ 168 #define SYSCLK_SEL_LSCLK (0 << 4) 169 #define LSCLK_DIV_1 (0 << 0) 170 #define LSCLK_DIV_2 (1 << 0) 171 172 /* Test & Debug */ 173 #define TSTCTL 0x0a00 174 #define PLL_DBG 0x0a04 175 176 static bool tc_test_pattern; 177 module_param_named(test, tc_test_pattern, bool, 0644); 178 179 struct tc_edp_link { 180 struct drm_dp_link base; 181 u8 assr; 182 int scrambler_dis; 183 int spread; 184 int coding8b10b; 185 u8 swing; 186 u8 preemp; 187 }; 188 189 struct tc_data { 190 struct device *dev; 191 struct regmap *regmap; 192 struct drm_dp_aux aux; 193 194 struct drm_bridge bridge; 195 struct drm_connector connector; 196 struct drm_panel *panel; 197 198 /* link settings */ 199 struct tc_edp_link link; 200 201 /* display edid */ 202 struct edid *edid; 203 /* current mode */ 204 struct drm_display_mode *mode; 205 206 u32 rev; 207 u8 assr; 208 209 struct gpio_desc *sd_gpio; 210 struct gpio_desc *reset_gpio; 211 struct clk *refclk; 212 }; 213 214 static inline struct tc_data *aux_to_tc(struct drm_dp_aux *a) 215 { 216 return container_of(a, struct tc_data, aux); 217 } 218 219 static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) 220 { 221 return container_of(b, struct tc_data, bridge); 222 } 223 224 static inline struct tc_data *connector_to_tc(struct drm_connector *c) 225 { 226 return container_of(c, struct tc_data, connector); 227 } 228 229 /* Simple macros to avoid repeated error checks */ 230 #define tc_write(reg, var) \ 231 do { \ 232 ret = regmap_write(tc->regmap, reg, var); \ 233 if (ret) \ 234 goto err; \ 235 } while (0) 236 #define tc_read(reg, var) \ 237 do { \ 238 ret = regmap_read(tc->regmap, reg, var); \ 239 if (ret) \ 240 goto err; \ 241 } while (0) 242 243 static inline int tc_poll_timeout(struct regmap *map, unsigned int addr, 244 unsigned int cond_mask, 245 unsigned int cond_value, 246 unsigned long sleep_us, u64 timeout_us) 247 { 248 ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); 249 unsigned int val; 250 int ret; 251 252 for (;;) { 253 ret = regmap_read(map, addr, &val); 254 if (ret) 255 break; 256 if ((val & cond_mask) == cond_value) 257 break; 258 if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { 259 ret = regmap_read(map, addr, &val); 260 break; 261 } 262 if (sleep_us) 263 usleep_range((sleep_us >> 2) + 1, sleep_us); 264 } 265 return ret ?: (((val & cond_mask) == cond_value) ? 0 : -ETIMEDOUT); 266 } 267 268 static int tc_aux_wait_busy(struct tc_data *tc, unsigned int timeout_ms) 269 { 270 return tc_poll_timeout(tc->regmap, DP0_AUXSTATUS, AUX_BUSY, 0, 271 1000, 1000 * timeout_ms); 272 } 273 274 static int tc_aux_get_status(struct tc_data *tc, u8 *reply) 275 { 276 int ret; 277 u32 value; 278 279 ret = regmap_read(tc->regmap, DP0_AUXSTATUS, &value); 280 if (ret < 0) 281 return ret; 282 if (value & AUX_BUSY) { 283 if (value & AUX_TIMEOUT) { 284 dev_err(tc->dev, "i2c access timeout!\n"); 285 return -ETIMEDOUT; 286 } 287 return -EBUSY; 288 } 289 290 *reply = (value & AUX_STATUS_MASK) >> AUX_STATUS_SHIFT; 291 return 0; 292 } 293 294 static ssize_t tc_aux_transfer(struct drm_dp_aux *aux, 295 struct drm_dp_aux_msg *msg) 296 { 297 struct tc_data *tc = aux_to_tc(aux); 298 size_t size = min_t(size_t, 8, msg->size); 299 u8 request = msg->request & ~DP_AUX_I2C_MOT; 300 u8 *buf = msg->buffer; 301 u32 tmp = 0; 302 int i = 0; 303 int ret; 304 305 if (size == 0) 306 return 0; 307 308 ret = tc_aux_wait_busy(tc, 100); 309 if (ret) 310 goto err; 311 312 if (request == DP_AUX_I2C_WRITE || request == DP_AUX_NATIVE_WRITE) { 313 /* Store data */ 314 while (i < size) { 315 if (request == DP_AUX_NATIVE_WRITE) 316 tmp = tmp | (buf[i] << (8 * (i & 0x3))); 317 else 318 tmp = (tmp << 8) | buf[i]; 319 i++; 320 if (((i % 4) == 0) || (i == size)) { 321 tc_write(DP0_AUXWDATA(i >> 2), tmp); 322 tmp = 0; 323 } 324 } 325 } else if (request != DP_AUX_I2C_READ && 326 request != DP_AUX_NATIVE_READ) { 327 return -EINVAL; 328 } 329 330 /* Store address */ 331 tc_write(DP0_AUXADDR, msg->address); 332 /* Start transfer */ 333 tc_write(DP0_AUXCFG0, ((size - 1) << 8) | request); 334 335 ret = tc_aux_wait_busy(tc, 100); 336 if (ret) 337 goto err; 338 339 ret = tc_aux_get_status(tc, &msg->reply); 340 if (ret) 341 goto err; 342 343 if (request == DP_AUX_I2C_READ || request == DP_AUX_NATIVE_READ) { 344 /* Read data */ 345 while (i < size) { 346 if ((i % 4) == 0) 347 tc_read(DP0_AUXRDATA(i >> 2), &tmp); 348 buf[i] = tmp & 0xff; 349 tmp = tmp >> 8; 350 i++; 351 } 352 } 353 354 return size; 355 err: 356 return ret; 357 } 358 359 static const char * const training_pattern1_errors[] = { 360 "No errors", 361 "Aux write error", 362 "Aux read error", 363 "Max voltage reached error", 364 "Loop counter expired error", 365 "res", "res", "res" 366 }; 367 368 static const char * const training_pattern2_errors[] = { 369 "No errors", 370 "Aux write error", 371 "Aux read error", 372 "Clock recovery failed error", 373 "Loop counter expired error", 374 "res", "res", "res" 375 }; 376 377 static u32 tc_srcctrl(struct tc_data *tc) 378 { 379 /* 380 * No training pattern, skew lane 1 data by two LSCLK cycles with 381 * respect to lane 0 data, AutoCorrect Mode = 0 382 */ 383 u32 reg = DP0_SRCCTRL_NOTP | DP0_SRCCTRL_LANESKEW; 384 385 if (tc->link.scrambler_dis) 386 reg |= DP0_SRCCTRL_SCRMBLDIS; /* Scrambler Disabled */ 387 if (tc->link.coding8b10b) 388 /* Enable 8/10B Encoder (TxData[19:16] not used) */ 389 reg |= DP0_SRCCTRL_EN810B; 390 if (tc->link.spread) 391 reg |= DP0_SRCCTRL_SSCG; /* Spread Spectrum Enable */ 392 if (tc->link.base.num_lanes == 2) 393 reg |= DP0_SRCCTRL_LANES_2; /* Two Main Channel Lanes */ 394 if (tc->link.base.rate != 162000) 395 reg |= DP0_SRCCTRL_BW27; /* 2.7 Gbps link */ 396 return reg; 397 } 398 399 static void tc_wait_pll_lock(struct tc_data *tc) 400 { 401 /* Wait for PLL to lock: up to 2.09 ms, depending on refclk */ 402 usleep_range(3000, 6000); 403 } 404 405 static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock) 406 { 407 int ret; 408 int i_pre, best_pre = 1; 409 int i_post, best_post = 1; 410 int div, best_div = 1; 411 int mul, best_mul = 1; 412 int delta, best_delta; 413 int ext_div[] = {1, 2, 3, 5, 7}; 414 int best_pixelclock = 0; 415 int vco_hi = 0; 416 417 dev_dbg(tc->dev, "PLL: requested %d pixelclock, ref %d\n", pixelclock, 418 refclk); 419 best_delta = pixelclock; 420 /* Loop over all possible ext_divs, skipping invalid configurations */ 421 for (i_pre = 0; i_pre < ARRAY_SIZE(ext_div); i_pre++) { 422 /* 423 * refclk / ext_pre_div should be in the 1 to 200 MHz range. 424 * We don't allow any refclk > 200 MHz, only check lower bounds. 425 */ 426 if (refclk / ext_div[i_pre] < 1000000) 427 continue; 428 for (i_post = 0; i_post < ARRAY_SIZE(ext_div); i_post++) { 429 for (div = 1; div <= 16; div++) { 430 u32 clk; 431 u64 tmp; 432 433 tmp = pixelclock * ext_div[i_pre] * 434 ext_div[i_post] * div; 435 do_div(tmp, refclk); 436 mul = tmp; 437 438 /* Check limits */ 439 if ((mul < 1) || (mul > 128)) 440 continue; 441 442 clk = (refclk / ext_div[i_pre] / div) * mul; 443 /* 444 * refclk * mul / (ext_pre_div * pre_div) 445 * should be in the 150 to 650 MHz range 446 */ 447 if ((clk > 650000000) || (clk < 150000000)) 448 continue; 449 450 clk = clk / ext_div[i_post]; 451 delta = clk - pixelclock; 452 453 if (abs(delta) < abs(best_delta)) { 454 best_pre = i_pre; 455 best_post = i_post; 456 best_div = div; 457 best_mul = mul; 458 best_delta = delta; 459 best_pixelclock = clk; 460 } 461 } 462 } 463 } 464 if (best_pixelclock == 0) { 465 dev_err(tc->dev, "Failed to calc clock for %d pixelclock\n", 466 pixelclock); 467 return -EINVAL; 468 } 469 470 dev_dbg(tc->dev, "PLL: got %d, delta %d\n", best_pixelclock, 471 best_delta); 472 dev_dbg(tc->dev, "PLL: %d / %d / %d * %d / %d\n", refclk, 473 ext_div[best_pre], best_div, best_mul, ext_div[best_post]); 474 475 /* if VCO >= 300 MHz */ 476 if (refclk / ext_div[best_pre] / best_div * best_mul >= 300000000) 477 vco_hi = 1; 478 /* see DS */ 479 if (best_div == 16) 480 best_div = 0; 481 if (best_mul == 128) 482 best_mul = 0; 483 484 /* Power up PLL and switch to bypass */ 485 tc_write(PXL_PLLCTRL, PLLBYP | PLLEN); 486 487 tc_write(PXL_PLLPARAM, 488 (vco_hi << 24) | /* For PLL VCO >= 300 MHz = 1 */ 489 (ext_div[best_pre] << 20) | /* External Pre-divider */ 490 (ext_div[best_post] << 16) | /* External Post-divider */ 491 IN_SEL_REFCLK | /* Use RefClk as PLL input */ 492 (best_div << 8) | /* Divider for PLL RefClk */ 493 (best_mul << 0)); /* Multiplier for PLL */ 494 495 /* Force PLL parameter update and disable bypass */ 496 tc_write(PXL_PLLCTRL, PLLUPDATE | PLLEN); 497 498 tc_wait_pll_lock(tc); 499 500 return 0; 501 err: 502 return ret; 503 } 504 505 static int tc_pxl_pll_dis(struct tc_data *tc) 506 { 507 /* Enable PLL bypass, power down PLL */ 508 return regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP); 509 } 510 511 static int tc_stream_clock_calc(struct tc_data *tc) 512 { 513 int ret; 514 /* 515 * If the Stream clock and Link Symbol clock are 516 * asynchronous with each other, the value of M changes over 517 * time. This way of generating link clock and stream 518 * clock is called Asynchronous Clock mode. The value M 519 * must change while the value N stays constant. The 520 * value of N in this Asynchronous Clock mode must be set 521 * to 2^15 or 32,768. 522 * 523 * LSCLK = 1/10 of high speed link clock 524 * 525 * f_STRMCLK = M/N * f_LSCLK 526 * M/N = f_STRMCLK / f_LSCLK 527 * 528 */ 529 tc_write(DP0_VIDMNGEN1, 32768); 530 531 return 0; 532 err: 533 return ret; 534 } 535 536 static int tc_aux_link_setup(struct tc_data *tc) 537 { 538 unsigned long rate; 539 u32 value; 540 int ret; 541 542 rate = clk_get_rate(tc->refclk); 543 switch (rate) { 544 case 38400000: 545 value = REF_FREQ_38M4; 546 break; 547 case 26000000: 548 value = REF_FREQ_26M; 549 break; 550 case 19200000: 551 value = REF_FREQ_19M2; 552 break; 553 case 13000000: 554 value = REF_FREQ_13M; 555 break; 556 default: 557 dev_err(tc->dev, "Invalid refclk rate: %lu Hz\n", rate); 558 return -EINVAL; 559 } 560 561 /* Setup DP-PHY / PLL */ 562 value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2; 563 tc_write(SYS_PLLPARAM, value); 564 565 tc_write(DP_PHY_CTRL, BGREN | PWR_SW_EN | BIT(2) | PHY_A0_EN); 566 567 /* 568 * Initially PLLs are in bypass. Force PLL parameter update, 569 * disable PLL bypass, enable PLL 570 */ 571 tc_write(DP0_PLLCTRL, PLLUPDATE | PLLEN); 572 tc_wait_pll_lock(tc); 573 574 tc_write(DP1_PLLCTRL, PLLUPDATE | PLLEN); 575 tc_wait_pll_lock(tc); 576 577 ret = tc_poll_timeout(tc->regmap, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 1, 578 1000); 579 if (ret == -ETIMEDOUT) { 580 dev_err(tc->dev, "Timeout waiting for PHY to become ready"); 581 return ret; 582 } else if (ret) 583 goto err; 584 585 /* Setup AUX link */ 586 tc_write(DP0_AUXCFG1, AUX_RX_FILTER_EN | 587 (0x06 << 8) | /* Aux Bit Period Calculator Threshold */ 588 (0x3f << 0)); /* Aux Response Timeout Timer */ 589 590 return 0; 591 err: 592 dev_err(tc->dev, "tc_aux_link_setup failed: %d\n", ret); 593 return ret; 594 } 595 596 static int tc_get_display_props(struct tc_data *tc) 597 { 598 int ret; 599 /* temp buffer */ 600 u8 tmp[8]; 601 602 /* Read DP Rx Link Capability */ 603 ret = drm_dp_link_probe(&tc->aux, &tc->link.base); 604 if (ret < 0) 605 goto err_dpcd_read; 606 if ((tc->link.base.rate != 162000) && (tc->link.base.rate != 270000)) 607 goto err_dpcd_inval; 608 609 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAX_DOWNSPREAD, tmp); 610 if (ret < 0) 611 goto err_dpcd_read; 612 tc->link.spread = tmp[0] & BIT(0); /* 0.5% down spread */ 613 614 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAIN_LINK_CHANNEL_CODING, tmp); 615 if (ret < 0) 616 goto err_dpcd_read; 617 tc->link.coding8b10b = tmp[0] & BIT(0); 618 tc->link.scrambler_dis = 0; 619 /* read assr */ 620 ret = drm_dp_dpcd_readb(&tc->aux, DP_EDP_CONFIGURATION_SET, tmp); 621 if (ret < 0) 622 goto err_dpcd_read; 623 tc->link.assr = tmp[0] & DP_ALTERNATE_SCRAMBLER_RESET_ENABLE; 624 625 dev_dbg(tc->dev, "DPCD rev: %d.%d, rate: %s, lanes: %d, framing: %s\n", 626 tc->link.base.revision >> 4, tc->link.base.revision & 0x0f, 627 (tc->link.base.rate == 162000) ? "1.62Gbps" : "2.7Gbps", 628 tc->link.base.num_lanes, 629 (tc->link.base.capabilities & DP_LINK_CAP_ENHANCED_FRAMING) ? 630 "enhanced" : "non-enhanced"); 631 dev_dbg(tc->dev, "ANSI 8B/10B: %d\n", tc->link.coding8b10b); 632 dev_dbg(tc->dev, "Display ASSR: %d, TC358767 ASSR: %d\n", 633 tc->link.assr, tc->assr); 634 635 return 0; 636 637 err_dpcd_read: 638 dev_err(tc->dev, "failed to read DPCD: %d\n", ret); 639 return ret; 640 err_dpcd_inval: 641 dev_err(tc->dev, "invalid DPCD\n"); 642 return -EINVAL; 643 } 644 645 static int tc_set_video_mode(struct tc_data *tc, struct drm_display_mode *mode) 646 { 647 int ret; 648 int vid_sync_dly; 649 int max_tu_symbol; 650 651 int left_margin = mode->htotal - mode->hsync_end; 652 int right_margin = mode->hsync_start - mode->hdisplay; 653 int hsync_len = mode->hsync_end - mode->hsync_start; 654 int upper_margin = mode->vtotal - mode->vsync_end; 655 int lower_margin = mode->vsync_start - mode->vdisplay; 656 int vsync_len = mode->vsync_end - mode->vsync_start; 657 658 dev_dbg(tc->dev, "set mode %dx%d\n", 659 mode->hdisplay, mode->vdisplay); 660 dev_dbg(tc->dev, "H margin %d,%d sync %d\n", 661 left_margin, right_margin, hsync_len); 662 dev_dbg(tc->dev, "V margin %d,%d sync %d\n", 663 upper_margin, lower_margin, vsync_len); 664 dev_dbg(tc->dev, "total: %dx%d\n", mode->htotal, mode->vtotal); 665 666 667 /* LCD Ctl Frame Size */ 668 tc_write(VPCTRL0, (0x40 << 20) /* VSDELAY */ | 669 OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED); 670 tc_write(HTIM01, (left_margin << 16) | /* H back porch */ 671 (hsync_len << 0)); /* Hsync */ 672 tc_write(HTIM02, (right_margin << 16) | /* H front porch */ 673 (mode->hdisplay << 0)); /* width */ 674 tc_write(VTIM01, (upper_margin << 16) | /* V back porch */ 675 (vsync_len << 0)); /* Vsync */ 676 tc_write(VTIM02, (lower_margin << 16) | /* V front porch */ 677 (mode->vdisplay << 0)); /* height */ 678 tc_write(VFUEN0, VFUEN); /* update settings */ 679 680 /* Test pattern settings */ 681 tc_write(TSTCTL, 682 (120 << 24) | /* Red Color component value */ 683 (20 << 16) | /* Green Color component value */ 684 (99 << 8) | /* Blue Color component value */ 685 (1 << 4) | /* Enable I2C Filter */ 686 (2 << 0) | /* Color bar Mode */ 687 0); 688 689 /* DP Main Stream Attributes */ 690 vid_sync_dly = hsync_len + left_margin + mode->hdisplay; 691 tc_write(DP0_VIDSYNCDELAY, 692 (0x003e << 16) | /* thresh_dly */ 693 (vid_sync_dly << 0)); 694 695 tc_write(DP0_TOTALVAL, (mode->vtotal << 16) | (mode->htotal)); 696 697 tc_write(DP0_STARTVAL, 698 ((upper_margin + vsync_len) << 16) | 699 ((left_margin + hsync_len) << 0)); 700 701 tc_write(DP0_ACTIVEVAL, (mode->vdisplay << 16) | (mode->hdisplay)); 702 703 tc_write(DP0_SYNCVAL, (vsync_len << 16) | (hsync_len << 0)); 704 705 tc_write(DPIPXLFMT, VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW | 706 DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 | DPI_BPP_RGB888); 707 708 /* 709 * Recommended maximum number of symbols transferred in a transfer unit: 710 * DIV_ROUND_UP((input active video bandwidth in bytes) * tu_size, 711 * (output active video bandwidth in bytes)) 712 * Must be less than tu_size. 713 */ 714 max_tu_symbol = TU_SIZE_RECOMMENDED - 1; 715 tc_write(DP0_MISC, (max_tu_symbol << 23) | TU_SIZE_RECOMMENDED | BPC_8); 716 717 return 0; 718 err: 719 return ret; 720 } 721 722 static int tc_link_training(struct tc_data *tc, int pattern) 723 { 724 const char * const *errors; 725 u32 srcctrl = tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS | 726 DP0_SRCCTRL_AUTOCORRECT; 727 int timeout; 728 int retry; 729 u32 value; 730 int ret; 731 732 if (pattern == DP_TRAINING_PATTERN_1) { 733 srcctrl |= DP0_SRCCTRL_TP1; 734 errors = training_pattern1_errors; 735 } else { 736 srcctrl |= DP0_SRCCTRL_TP2; 737 errors = training_pattern2_errors; 738 } 739 740 /* Set DPCD 0x102 for Training Part 1 or 2 */ 741 tc_write(DP0_SNKLTCTRL, DP_LINK_SCRAMBLING_DISABLE | pattern); 742 743 tc_write(DP0_LTLOOPCTRL, 744 (0x0f << 28) | /* Defer Iteration Count */ 745 (0x0f << 24) | /* Loop Iteration Count */ 746 (0x0d << 0)); /* Loop Timer Delay */ 747 748 retry = 5; 749 do { 750 /* Set DP0 Training Pattern */ 751 tc_write(DP0_SRCCTRL, srcctrl); 752 753 /* Enable DP0 to start Link Training */ 754 tc_write(DP0CTL, DP_EN); 755 756 /* wait */ 757 timeout = 1000; 758 do { 759 tc_read(DP0_LTSTAT, &value); 760 udelay(1); 761 } while ((!(value & LT_LOOPDONE)) && (--timeout)); 762 if (timeout == 0) { 763 dev_err(tc->dev, "Link training timeout!\n"); 764 } else { 765 int pattern = (value >> 11) & 0x3; 766 int error = (value >> 8) & 0x7; 767 768 dev_dbg(tc->dev, 769 "Link training phase %d done after %d uS: %s\n", 770 pattern, 1000 - timeout, errors[error]); 771 if (pattern == DP_TRAINING_PATTERN_1 && error == 0) 772 break; 773 if (pattern == DP_TRAINING_PATTERN_2) { 774 value &= LT_CHANNEL1_EQ_BITS | 775 LT_INTERLANE_ALIGN_DONE | 776 LT_CHANNEL0_EQ_BITS; 777 /* in case of two lanes */ 778 if ((tc->link.base.num_lanes == 2) && 779 (value == (LT_CHANNEL1_EQ_BITS | 780 LT_INTERLANE_ALIGN_DONE | 781 LT_CHANNEL0_EQ_BITS))) 782 break; 783 /* in case of one line */ 784 if ((tc->link.base.num_lanes == 1) && 785 (value == (LT_INTERLANE_ALIGN_DONE | 786 LT_CHANNEL0_EQ_BITS))) 787 break; 788 } 789 } 790 /* restart */ 791 tc_write(DP0CTL, 0); 792 usleep_range(10, 20); 793 } while (--retry); 794 if (retry == 0) { 795 dev_err(tc->dev, "Failed to finish training phase %d\n", 796 pattern); 797 } 798 799 return 0; 800 err: 801 return ret; 802 } 803 804 static int tc_main_link_setup(struct tc_data *tc) 805 { 806 struct drm_dp_aux *aux = &tc->aux; 807 struct device *dev = tc->dev; 808 unsigned int rate; 809 u32 dp_phy_ctrl; 810 int timeout; 811 bool aligned; 812 bool ready; 813 u32 value; 814 int ret; 815 u8 tmp[8]; 816 817 /* display mode should be set at this point */ 818 if (!tc->mode) 819 return -EINVAL; 820 821 /* from excel file - DP0_SrcCtrl */ 822 tc_write(DP0_SRCCTRL, DP0_SRCCTRL_SCRMBLDIS | DP0_SRCCTRL_EN810B | 823 DP0_SRCCTRL_LANESKEW | DP0_SRCCTRL_LANES_2 | 824 DP0_SRCCTRL_BW27 | DP0_SRCCTRL_AUTOCORRECT); 825 /* from excel file - DP1_SrcCtrl */ 826 tc_write(0x07a0, 0x00003083); 827 828 rate = clk_get_rate(tc->refclk); 829 switch (rate) { 830 case 38400000: 831 value = REF_FREQ_38M4; 832 break; 833 case 26000000: 834 value = REF_FREQ_26M; 835 break; 836 case 19200000: 837 value = REF_FREQ_19M2; 838 break; 839 case 13000000: 840 value = REF_FREQ_13M; 841 break; 842 default: 843 return -EINVAL; 844 } 845 value |= SYSCLK_SEL_LSCLK | LSCLK_DIV_2; 846 tc_write(SYS_PLLPARAM, value); 847 /* Setup Main Link */ 848 dp_phy_ctrl = BGREN | PWR_SW_EN | BIT(2) | PHY_A0_EN | PHY_M0_EN; 849 tc_write(DP_PHY_CTRL, dp_phy_ctrl); 850 msleep(100); 851 852 /* PLL setup */ 853 tc_write(DP0_PLLCTRL, PLLUPDATE | PLLEN); 854 tc_wait_pll_lock(tc); 855 856 tc_write(DP1_PLLCTRL, PLLUPDATE | PLLEN); 857 tc_wait_pll_lock(tc); 858 859 /* PXL PLL setup */ 860 if (tc_test_pattern) { 861 ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk), 862 1000 * tc->mode->clock); 863 if (ret) 864 goto err; 865 } 866 867 /* Reset/Enable Main Links */ 868 dp_phy_ctrl |= DP_PHY_RST | PHY_M1_RST | PHY_M0_RST; 869 tc_write(DP_PHY_CTRL, dp_phy_ctrl); 870 usleep_range(100, 200); 871 dp_phy_ctrl &= ~(DP_PHY_RST | PHY_M1_RST | PHY_M0_RST); 872 tc_write(DP_PHY_CTRL, dp_phy_ctrl); 873 874 timeout = 1000; 875 do { 876 tc_read(DP_PHY_CTRL, &value); 877 udelay(1); 878 } while ((!(value & PHY_RDY)) && (--timeout)); 879 880 if (timeout == 0) { 881 dev_err(dev, "timeout waiting for phy become ready"); 882 return -ETIMEDOUT; 883 } 884 885 /* Set misc: 8 bits per color */ 886 ret = regmap_update_bits(tc->regmap, DP0_MISC, BPC_8, BPC_8); 887 if (ret) 888 goto err; 889 890 /* 891 * ASSR mode 892 * on TC358767 side ASSR configured through strap pin 893 * seems there is no way to change this setting from SW 894 * 895 * check is tc configured for same mode 896 */ 897 if (tc->assr != tc->link.assr) { 898 dev_dbg(dev, "Trying to set display to ASSR: %d\n", 899 tc->assr); 900 /* try to set ASSR on display side */ 901 tmp[0] = tc->assr; 902 ret = drm_dp_dpcd_writeb(aux, DP_EDP_CONFIGURATION_SET, tmp[0]); 903 if (ret < 0) 904 goto err_dpcd_read; 905 /* read back */ 906 ret = drm_dp_dpcd_readb(aux, DP_EDP_CONFIGURATION_SET, tmp); 907 if (ret < 0) 908 goto err_dpcd_read; 909 910 if (tmp[0] != tc->assr) { 911 dev_dbg(dev, "Failed to switch display ASSR to %d, falling back to unscrambled mode\n", 912 tc->assr); 913 /* trying with disabled scrambler */ 914 tc->link.scrambler_dis = 1; 915 } 916 } 917 918 /* Setup Link & DPRx Config for Training */ 919 ret = drm_dp_link_configure(aux, &tc->link.base); 920 if (ret < 0) 921 goto err_dpcd_write; 922 923 /* DOWNSPREAD_CTRL */ 924 tmp[0] = tc->link.spread ? DP_SPREAD_AMP_0_5 : 0x00; 925 /* MAIN_LINK_CHANNEL_CODING_SET */ 926 tmp[1] = tc->link.coding8b10b ? DP_SET_ANSI_8B10B : 0x00; 927 ret = drm_dp_dpcd_write(aux, DP_DOWNSPREAD_CTRL, tmp, 2); 928 if (ret < 0) 929 goto err_dpcd_write; 930 931 ret = tc_link_training(tc, DP_TRAINING_PATTERN_1); 932 if (ret) 933 goto err; 934 935 ret = tc_link_training(tc, DP_TRAINING_PATTERN_2); 936 if (ret) 937 goto err; 938 939 /* Clear DPCD 0x102 */ 940 /* Note: Can Not use DP0_SNKLTCTRL (0x06E4) short cut */ 941 tmp[0] = tc->link.scrambler_dis ? DP_LINK_SCRAMBLING_DISABLE : 0x00; 942 ret = drm_dp_dpcd_writeb(aux, DP_TRAINING_PATTERN_SET, tmp[0]); 943 if (ret < 0) 944 goto err_dpcd_write; 945 946 /* Clear Training Pattern, set AutoCorrect Mode = 1 */ 947 tc_write(DP0_SRCCTRL, tc_srcctrl(tc) | DP0_SRCCTRL_AUTOCORRECT); 948 949 /* Wait */ 950 timeout = 100; 951 do { 952 udelay(1); 953 /* Read DPCD 0x202-0x207 */ 954 ret = drm_dp_dpcd_read_link_status(aux, tmp + 2); 955 if (ret < 0) 956 goto err_dpcd_read; 957 ready = (tmp[2] == ((DP_CHANNEL_EQ_BITS << 4) | /* Lane1 */ 958 DP_CHANNEL_EQ_BITS)); /* Lane0 */ 959 aligned = tmp[4] & DP_INTERLANE_ALIGN_DONE; 960 } while ((--timeout) && !(ready && aligned)); 961 962 if (timeout == 0) { 963 /* Read DPCD 0x200-0x201 */ 964 ret = drm_dp_dpcd_read(aux, DP_SINK_COUNT, tmp, 2); 965 if (ret < 0) 966 goto err_dpcd_read; 967 dev_info(dev, "0x0200 SINK_COUNT: 0x%02x\n", tmp[0]); 968 dev_info(dev, "0x0201 DEVICE_SERVICE_IRQ_VECTOR: 0x%02x\n", 969 tmp[1]); 970 dev_info(dev, "0x0202 LANE0_1_STATUS: 0x%02x\n", tmp[2]); 971 dev_info(dev, "0x0204 LANE_ALIGN_STATUS_UPDATED: 0x%02x\n", 972 tmp[4]); 973 dev_info(dev, "0x0205 SINK_STATUS: 0x%02x\n", tmp[5]); 974 dev_info(dev, "0x0206 ADJUST_REQUEST_LANE0_1: 0x%02x\n", 975 tmp[6]); 976 977 if (!ready) 978 dev_err(dev, "Lane0/1 not ready\n"); 979 if (!aligned) 980 dev_err(dev, "Lane0/1 not aligned\n"); 981 return -EAGAIN; 982 } 983 984 ret = tc_set_video_mode(tc, tc->mode); 985 if (ret) 986 goto err; 987 988 /* Set M/N */ 989 ret = tc_stream_clock_calc(tc); 990 if (ret) 991 goto err; 992 993 return 0; 994 err_dpcd_read: 995 dev_err(tc->dev, "Failed to read DPCD: %d\n", ret); 996 return ret; 997 err_dpcd_write: 998 dev_err(tc->dev, "Failed to write DPCD: %d\n", ret); 999 err: 1000 return ret; 1001 } 1002 1003 static int tc_main_link_stream(struct tc_data *tc, int state) 1004 { 1005 int ret; 1006 u32 value; 1007 1008 dev_dbg(tc->dev, "stream: %d\n", state); 1009 1010 if (state) { 1011 value = VID_MN_GEN | DP_EN; 1012 if (tc->link.base.capabilities & DP_LINK_CAP_ENHANCED_FRAMING) 1013 value |= EF_EN; 1014 tc_write(DP0CTL, value); 1015 /* 1016 * VID_EN assertion should be delayed by at least N * LSCLK 1017 * cycles from the time VID_MN_GEN is enabled in order to 1018 * generate stable values for VID_M. LSCLK is 270 MHz or 1019 * 162 MHz, VID_N is set to 32768 in tc_stream_clock_calc(), 1020 * so a delay of at least 203 us should suffice. 1021 */ 1022 usleep_range(500, 1000); 1023 value |= VID_EN; 1024 tc_write(DP0CTL, value); 1025 /* Set input interface */ 1026 value = DP0_AUDSRC_NO_INPUT; 1027 if (tc_test_pattern) 1028 value |= DP0_VIDSRC_COLOR_BAR; 1029 else 1030 value |= DP0_VIDSRC_DPI_RX; 1031 tc_write(SYSCTRL, value); 1032 } else { 1033 tc_write(DP0CTL, 0); 1034 } 1035 1036 return 0; 1037 err: 1038 return ret; 1039 } 1040 1041 static void tc_bridge_pre_enable(struct drm_bridge *bridge) 1042 { 1043 struct tc_data *tc = bridge_to_tc(bridge); 1044 1045 drm_panel_prepare(tc->panel); 1046 } 1047 1048 static void tc_bridge_enable(struct drm_bridge *bridge) 1049 { 1050 struct tc_data *tc = bridge_to_tc(bridge); 1051 int ret; 1052 1053 ret = tc_main_link_setup(tc); 1054 if (ret < 0) { 1055 dev_err(tc->dev, "main link setup error: %d\n", ret); 1056 return; 1057 } 1058 1059 ret = tc_main_link_stream(tc, 1); 1060 if (ret < 0) { 1061 dev_err(tc->dev, "main link stream start error: %d\n", ret); 1062 return; 1063 } 1064 1065 drm_panel_enable(tc->panel); 1066 } 1067 1068 static void tc_bridge_disable(struct drm_bridge *bridge) 1069 { 1070 struct tc_data *tc = bridge_to_tc(bridge); 1071 int ret; 1072 1073 drm_panel_disable(tc->panel); 1074 1075 ret = tc_main_link_stream(tc, 0); 1076 if (ret < 0) 1077 dev_err(tc->dev, "main link stream stop error: %d\n", ret); 1078 } 1079 1080 static void tc_bridge_post_disable(struct drm_bridge *bridge) 1081 { 1082 struct tc_data *tc = bridge_to_tc(bridge); 1083 1084 drm_panel_unprepare(tc->panel); 1085 } 1086 1087 static bool tc_bridge_mode_fixup(struct drm_bridge *bridge, 1088 const struct drm_display_mode *mode, 1089 struct drm_display_mode *adj) 1090 { 1091 /* Fixup sync polarities, both hsync and vsync are active low */ 1092 adj->flags = mode->flags; 1093 adj->flags |= (DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC); 1094 adj->flags &= ~(DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC); 1095 1096 return true; 1097 } 1098 1099 static int tc_connector_mode_valid(struct drm_connector *connector, 1100 struct drm_display_mode *mode) 1101 { 1102 /* Accept any mode */ 1103 return MODE_OK; 1104 } 1105 1106 static void tc_bridge_mode_set(struct drm_bridge *bridge, 1107 struct drm_display_mode *mode, 1108 struct drm_display_mode *adj) 1109 { 1110 struct tc_data *tc = bridge_to_tc(bridge); 1111 1112 tc->mode = mode; 1113 } 1114 1115 static int tc_connector_get_modes(struct drm_connector *connector) 1116 { 1117 struct tc_data *tc = connector_to_tc(connector); 1118 struct edid *edid; 1119 unsigned int count; 1120 1121 if (tc->panel && tc->panel->funcs && tc->panel->funcs->get_modes) { 1122 count = tc->panel->funcs->get_modes(tc->panel); 1123 if (count > 0) 1124 return count; 1125 } 1126 1127 edid = drm_get_edid(connector, &tc->aux.ddc); 1128 1129 kfree(tc->edid); 1130 tc->edid = edid; 1131 if (!edid) 1132 return 0; 1133 1134 drm_mode_connector_update_edid_property(connector, edid); 1135 count = drm_add_edid_modes(connector, edid); 1136 1137 return count; 1138 } 1139 1140 static void tc_connector_set_polling(struct tc_data *tc, 1141 struct drm_connector *connector) 1142 { 1143 /* TODO: add support for HPD */ 1144 connector->polled = DRM_CONNECTOR_POLL_CONNECT | 1145 DRM_CONNECTOR_POLL_DISCONNECT; 1146 } 1147 1148 static struct drm_encoder * 1149 tc_connector_best_encoder(struct drm_connector *connector) 1150 { 1151 struct tc_data *tc = connector_to_tc(connector); 1152 1153 return tc->bridge.encoder; 1154 } 1155 1156 static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { 1157 .get_modes = tc_connector_get_modes, 1158 .mode_valid = tc_connector_mode_valid, 1159 .best_encoder = tc_connector_best_encoder, 1160 }; 1161 1162 static const struct drm_connector_funcs tc_connector_funcs = { 1163 .dpms = drm_atomic_helper_connector_dpms, 1164 .fill_modes = drm_helper_probe_single_connector_modes, 1165 .destroy = drm_connector_cleanup, 1166 .reset = drm_atomic_helper_connector_reset, 1167 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 1168 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1169 }; 1170 1171 static int tc_bridge_attach(struct drm_bridge *bridge) 1172 { 1173 u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24; 1174 struct tc_data *tc = bridge_to_tc(bridge); 1175 struct drm_device *drm = bridge->dev; 1176 int ret; 1177 1178 /* Create eDP connector */ 1179 drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); 1180 ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, 1181 DRM_MODE_CONNECTOR_eDP); 1182 if (ret) 1183 return ret; 1184 1185 if (tc->panel) 1186 drm_panel_attach(tc->panel, &tc->connector); 1187 1188 drm_display_info_set_bus_formats(&tc->connector.display_info, 1189 &bus_format, 1); 1190 drm_mode_connector_attach_encoder(&tc->connector, tc->bridge.encoder); 1191 1192 return 0; 1193 } 1194 1195 static const struct drm_bridge_funcs tc_bridge_funcs = { 1196 .attach = tc_bridge_attach, 1197 .mode_set = tc_bridge_mode_set, 1198 .pre_enable = tc_bridge_pre_enable, 1199 .enable = tc_bridge_enable, 1200 .disable = tc_bridge_disable, 1201 .post_disable = tc_bridge_post_disable, 1202 .mode_fixup = tc_bridge_mode_fixup, 1203 }; 1204 1205 static bool tc_readable_reg(struct device *dev, unsigned int reg) 1206 { 1207 return reg != SYSCTRL; 1208 } 1209 1210 static const struct regmap_range tc_volatile_ranges[] = { 1211 regmap_reg_range(DP0_AUXWDATA(0), DP0_AUXSTATUS), 1212 regmap_reg_range(DP0_LTSTAT, DP0_SNKLTCHGREQ), 1213 regmap_reg_range(DP_PHY_CTRL, DP_PHY_CTRL), 1214 regmap_reg_range(DP0_PLLCTRL, PXL_PLLCTRL), 1215 regmap_reg_range(VFUEN0, VFUEN0), 1216 }; 1217 1218 static const struct regmap_access_table tc_volatile_table = { 1219 .yes_ranges = tc_volatile_ranges, 1220 .n_yes_ranges = ARRAY_SIZE(tc_volatile_ranges), 1221 }; 1222 1223 static bool tc_writeable_reg(struct device *dev, unsigned int reg) 1224 { 1225 return (reg != TC_IDREG) && 1226 (reg != DP0_LTSTAT) && 1227 (reg != DP0_SNKLTCHGREQ); 1228 } 1229 1230 static const struct regmap_config tc_regmap_config = { 1231 .name = "tc358767", 1232 .reg_bits = 16, 1233 .val_bits = 32, 1234 .reg_stride = 4, 1235 .max_register = PLL_DBG, 1236 .cache_type = REGCACHE_RBTREE, 1237 .readable_reg = tc_readable_reg, 1238 .volatile_table = &tc_volatile_table, 1239 .writeable_reg = tc_writeable_reg, 1240 .reg_format_endian = REGMAP_ENDIAN_BIG, 1241 .val_format_endian = REGMAP_ENDIAN_LITTLE, 1242 }; 1243 1244 static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) 1245 { 1246 struct device *dev = &client->dev; 1247 struct device_node *ep; 1248 struct tc_data *tc; 1249 int ret; 1250 1251 tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); 1252 if (!tc) 1253 return -ENOMEM; 1254 1255 tc->dev = dev; 1256 1257 /* port@2 is the output port */ 1258 ep = of_graph_get_endpoint_by_regs(dev->of_node, 2, -1); 1259 if (ep) { 1260 struct device_node *remote; 1261 1262 remote = of_graph_get_remote_port_parent(ep); 1263 if (!remote) { 1264 dev_warn(dev, "endpoint %s not connected\n", 1265 ep->full_name); 1266 of_node_put(ep); 1267 return -ENODEV; 1268 } 1269 of_node_put(ep); 1270 tc->panel = of_drm_find_panel(remote); 1271 if (tc->panel) { 1272 dev_dbg(dev, "found panel %s\n", remote->full_name); 1273 } else { 1274 dev_dbg(dev, "waiting for panel %s\n", 1275 remote->full_name); 1276 of_node_put(remote); 1277 return -EPROBE_DEFER; 1278 } 1279 of_node_put(remote); 1280 } 1281 1282 /* Shut down GPIO is optional */ 1283 tc->sd_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_HIGH); 1284 if (IS_ERR(tc->sd_gpio)) 1285 return PTR_ERR(tc->sd_gpio); 1286 1287 if (tc->sd_gpio) { 1288 gpiod_set_value_cansleep(tc->sd_gpio, 0); 1289 usleep_range(5000, 10000); 1290 } 1291 1292 /* Reset GPIO is optional */ 1293 tc->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1294 if (IS_ERR(tc->reset_gpio)) 1295 return PTR_ERR(tc->reset_gpio); 1296 1297 if (tc->reset_gpio) { 1298 gpiod_set_value_cansleep(tc->reset_gpio, 1); 1299 usleep_range(5000, 10000); 1300 } 1301 1302 tc->refclk = devm_clk_get(dev, "ref"); 1303 if (IS_ERR(tc->refclk)) { 1304 ret = PTR_ERR(tc->refclk); 1305 dev_err(dev, "Failed to get refclk: %d\n", ret); 1306 return ret; 1307 } 1308 1309 tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); 1310 if (IS_ERR(tc->regmap)) { 1311 ret = PTR_ERR(tc->regmap); 1312 dev_err(dev, "Failed to initialize regmap: %d\n", ret); 1313 return ret; 1314 } 1315 1316 ret = regmap_read(tc->regmap, TC_IDREG, &tc->rev); 1317 if (ret) { 1318 dev_err(tc->dev, "can not read device ID: %d\n", ret); 1319 return ret; 1320 } 1321 1322 if ((tc->rev != 0x6601) && (tc->rev != 0x6603)) { 1323 dev_err(tc->dev, "invalid device ID: 0x%08x\n", tc->rev); 1324 return -EINVAL; 1325 } 1326 1327 tc->assr = (tc->rev == 0x6601); /* Enable ASSR for eDP panels */ 1328 1329 ret = tc_aux_link_setup(tc); 1330 if (ret) 1331 return ret; 1332 1333 /* Register DP AUX channel */ 1334 tc->aux.name = "TC358767 AUX i2c adapter"; 1335 tc->aux.dev = tc->dev; 1336 tc->aux.transfer = tc_aux_transfer; 1337 ret = drm_dp_aux_register(&tc->aux); 1338 if (ret) 1339 return ret; 1340 1341 ret = tc_get_display_props(tc); 1342 if (ret) 1343 goto err_unregister_aux; 1344 1345 tc_connector_set_polling(tc, &tc->connector); 1346 1347 tc->bridge.funcs = &tc_bridge_funcs; 1348 tc->bridge.of_node = dev->of_node; 1349 ret = drm_bridge_add(&tc->bridge); 1350 if (ret) { 1351 dev_err(dev, "Failed to add drm_bridge: %d\n", ret); 1352 goto err_unregister_aux; 1353 } 1354 1355 i2c_set_clientdata(client, tc); 1356 1357 return 0; 1358 err_unregister_aux: 1359 drm_dp_aux_unregister(&tc->aux); 1360 return ret; 1361 } 1362 1363 static int tc_remove(struct i2c_client *client) 1364 { 1365 struct tc_data *tc = i2c_get_clientdata(client); 1366 1367 drm_bridge_remove(&tc->bridge); 1368 drm_dp_aux_unregister(&tc->aux); 1369 1370 tc_pxl_pll_dis(tc); 1371 1372 return 0; 1373 } 1374 1375 static const struct i2c_device_id tc358767_i2c_ids[] = { 1376 { "tc358767", 0 }, 1377 { } 1378 }; 1379 MODULE_DEVICE_TABLE(i2c, tc358767_i2c_ids); 1380 1381 static const struct of_device_id tc358767_of_ids[] = { 1382 { .compatible = "toshiba,tc358767", }, 1383 { } 1384 }; 1385 MODULE_DEVICE_TABLE(of, tc358767_of_ids); 1386 1387 static struct i2c_driver tc358767_driver = { 1388 .driver = { 1389 .name = "tc358767", 1390 .of_match_table = tc358767_of_ids, 1391 }, 1392 .id_table = tc358767_i2c_ids, 1393 .probe = tc_probe, 1394 .remove = tc_remove, 1395 }; 1396 module_i2c_driver(tc358767_driver); 1397 1398 MODULE_AUTHOR("Andrey Gusakov <andrey.gusakov@cogentembedded.com>"); 1399 MODULE_DESCRIPTION("tc358767 eDP encoder driver"); 1400 MODULE_LICENSE("GPL"); 1401