1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * tc358767 eDP bridge driver 4 * 5 * Copyright (C) 2016 CogentEmbedded Inc 6 * Author: Andrey Gusakov <andrey.gusakov@cogentembedded.com> 7 * 8 * Copyright (C) 2016 Pengutronix, Philipp Zabel <p.zabel@pengutronix.de> 9 * 10 * Copyright (C) 2016 Zodiac Inflight Innovations 11 * 12 * Initially based on: drivers/gpu/drm/i2c/tda998x_drv.c 13 * 14 * Copyright (C) 2012 Texas Instruments 15 * Author: Rob Clark <robdclark@gmail.com> 16 */ 17 18 #include <linux/bitfield.h> 19 #include <linux/clk.h> 20 #include <linux/device.h> 21 #include <linux/gpio/consumer.h> 22 #include <linux/i2c.h> 23 #include <linux/kernel.h> 24 #include <linux/module.h> 25 #include <linux/regmap.h> 26 #include <linux/slab.h> 27 28 #include <drm/drm_atomic_helper.h> 29 #include <drm/drm_bridge.h> 30 #include <drm/dp/drm_dp_helper.h> 31 #include <drm/drm_edid.h> 32 #include <drm/drm_of.h> 33 #include <drm/drm_panel.h> 34 #include <drm/drm_print.h> 35 #include <drm/drm_probe_helper.h> 36 37 /* Registers */ 38 39 /* Display Parallel Interface */ 40 #define DPIPXLFMT 0x0440 41 #define VS_POL_ACTIVE_LOW (1 << 10) 42 #define HS_POL_ACTIVE_LOW (1 << 9) 43 #define DE_POL_ACTIVE_HIGH (0 << 8) 44 #define SUB_CFG_TYPE_CONFIG1 (0 << 2) /* LSB aligned */ 45 #define SUB_CFG_TYPE_CONFIG2 (1 << 2) /* Loosely Packed */ 46 #define SUB_CFG_TYPE_CONFIG3 (2 << 2) /* LSB aligned 8-bit */ 47 #define DPI_BPP_RGB888 (0 << 0) 48 #define DPI_BPP_RGB666 (1 << 0) 49 #define DPI_BPP_RGB565 (2 << 0) 50 51 /* Video Path */ 52 #define VPCTRL0 0x0450 53 #define VSDELAY GENMASK(31, 20) 54 #define OPXLFMT_RGB666 (0 << 8) 55 #define OPXLFMT_RGB888 (1 << 8) 56 #define FRMSYNC_DISABLED (0 << 4) /* Video Timing Gen Disabled */ 57 #define FRMSYNC_ENABLED (1 << 4) /* Video Timing Gen Enabled */ 58 #define MSF_DISABLED (0 << 0) /* Magic Square FRC disabled */ 59 #define MSF_ENABLED (1 << 0) /* Magic Square FRC enabled */ 60 #define HTIM01 0x0454 61 #define HPW GENMASK(8, 0) 62 #define HBPR GENMASK(24, 16) 63 #define HTIM02 0x0458 64 #define HDISPR GENMASK(10, 0) 65 #define HFPR GENMASK(24, 16) 66 #define VTIM01 0x045c 67 #define VSPR GENMASK(7, 0) 68 #define VBPR GENMASK(23, 16) 69 #define VTIM02 0x0460 70 #define VFPR GENMASK(23, 16) 71 #define VDISPR GENMASK(10, 0) 72 #define VFUEN0 0x0464 73 #define VFUEN BIT(0) /* Video Frame Timing Upload */ 74 75 /* System */ 76 #define TC_IDREG 0x0500 77 #define SYSSTAT 0x0508 78 #define SYSCTRL 0x0510 79 #define DP0_AUDSRC_NO_INPUT (0 << 3) 80 #define DP0_AUDSRC_I2S_RX (1 << 3) 81 #define DP0_VIDSRC_NO_INPUT (0 << 0) 82 #define DP0_VIDSRC_DSI_RX (1 << 0) 83 #define DP0_VIDSRC_DPI_RX (2 << 0) 84 #define DP0_VIDSRC_COLOR_BAR (3 << 0) 85 #define SYSRSTENB 0x050c 86 #define ENBI2C (1 << 0) 87 #define ENBLCD0 (1 << 2) 88 #define ENBBM (1 << 3) 89 #define ENBDSIRX (1 << 4) 90 #define ENBREG (1 << 5) 91 #define ENBHDCP (1 << 8) 92 #define GPIOM 0x0540 93 #define GPIOC 0x0544 94 #define GPIOO 0x0548 95 #define GPIOI 0x054c 96 #define INTCTL_G 0x0560 97 #define INTSTS_G 0x0564 98 99 #define INT_SYSERR BIT(16) 100 #define INT_GPIO_H(x) (1 << (x == 0 ? 2 : 10)) 101 #define INT_GPIO_LC(x) (1 << (x == 0 ? 3 : 11)) 102 103 #define INT_GP0_LCNT 0x0584 104 #define INT_GP1_LCNT 0x0588 105 106 /* Control */ 107 #define DP0CTL 0x0600 108 #define VID_MN_GEN BIT(6) /* Auto-generate M/N values */ 109 #define EF_EN BIT(5) /* Enable Enhanced Framing */ 110 #define VID_EN BIT(1) /* Video transmission enable */ 111 #define DP_EN BIT(0) /* Enable DPTX function */ 112 113 /* Clocks */ 114 #define DP0_VIDMNGEN0 0x0610 115 #define DP0_VIDMNGEN1 0x0614 116 #define DP0_VMNGENSTATUS 0x0618 117 118 /* Main Channel */ 119 #define DP0_SECSAMPLE 0x0640 120 #define DP0_VIDSYNCDELAY 0x0644 121 #define VID_SYNC_DLY GENMASK(15, 0) 122 #define THRESH_DLY GENMASK(31, 16) 123 124 #define DP0_TOTALVAL 0x0648 125 #define H_TOTAL GENMASK(15, 0) 126 #define V_TOTAL GENMASK(31, 16) 127 #define DP0_STARTVAL 0x064c 128 #define H_START GENMASK(15, 0) 129 #define V_START GENMASK(31, 16) 130 #define DP0_ACTIVEVAL 0x0650 131 #define H_ACT GENMASK(15, 0) 132 #define V_ACT GENMASK(31, 16) 133 134 #define DP0_SYNCVAL 0x0654 135 #define VS_WIDTH GENMASK(30, 16) 136 #define HS_WIDTH GENMASK(14, 0) 137 #define SYNCVAL_HS_POL_ACTIVE_LOW (1 << 15) 138 #define SYNCVAL_VS_POL_ACTIVE_LOW (1 << 31) 139 #define DP0_MISC 0x0658 140 #define TU_SIZE_RECOMMENDED (63) /* LSCLK cycles per TU */ 141 #define MAX_TU_SYMBOL GENMASK(28, 23) 142 #define TU_SIZE GENMASK(21, 16) 143 #define BPC_6 (0 << 5) 144 #define BPC_8 (1 << 5) 145 146 /* AUX channel */ 147 #define DP0_AUXCFG0 0x0660 148 #define DP0_AUXCFG0_BSIZE GENMASK(11, 8) 149 #define DP0_AUXCFG0_ADDR_ONLY BIT(4) 150 #define DP0_AUXCFG1 0x0664 151 #define AUX_RX_FILTER_EN BIT(16) 152 153 #define DP0_AUXADDR 0x0668 154 #define DP0_AUXWDATA(i) (0x066c + (i) * 4) 155 #define DP0_AUXRDATA(i) (0x067c + (i) * 4) 156 #define DP0_AUXSTATUS 0x068c 157 #define AUX_BYTES GENMASK(15, 8) 158 #define AUX_STATUS GENMASK(7, 4) 159 #define AUX_TIMEOUT BIT(1) 160 #define AUX_BUSY BIT(0) 161 #define DP0_AUXI2CADR 0x0698 162 163 /* Link Training */ 164 #define DP0_SRCCTRL 0x06a0 165 #define DP0_SRCCTRL_SCRMBLDIS BIT(13) 166 #define DP0_SRCCTRL_EN810B BIT(12) 167 #define DP0_SRCCTRL_NOTP (0 << 8) 168 #define DP0_SRCCTRL_TP1 (1 << 8) 169 #define DP0_SRCCTRL_TP2 (2 << 8) 170 #define DP0_SRCCTRL_LANESKEW BIT(7) 171 #define DP0_SRCCTRL_SSCG BIT(3) 172 #define DP0_SRCCTRL_LANES_1 (0 << 2) 173 #define DP0_SRCCTRL_LANES_2 (1 << 2) 174 #define DP0_SRCCTRL_BW27 (1 << 1) 175 #define DP0_SRCCTRL_BW162 (0 << 1) 176 #define DP0_SRCCTRL_AUTOCORRECT BIT(0) 177 #define DP0_LTSTAT 0x06d0 178 #define LT_LOOPDONE BIT(13) 179 #define LT_STATUS_MASK (0x1f << 8) 180 #define LT_CHANNEL1_EQ_BITS (DP_CHANNEL_EQ_BITS << 4) 181 #define LT_INTERLANE_ALIGN_DONE BIT(3) 182 #define LT_CHANNEL0_EQ_BITS (DP_CHANNEL_EQ_BITS) 183 #define DP0_SNKLTCHGREQ 0x06d4 184 #define DP0_LTLOOPCTRL 0x06d8 185 #define DP0_SNKLTCTRL 0x06e4 186 187 #define DP1_SRCCTRL 0x07a0 188 189 /* PHY */ 190 #define DP_PHY_CTRL 0x0800 191 #define DP_PHY_RST BIT(28) /* DP PHY Global Soft Reset */ 192 #define BGREN BIT(25) /* AUX PHY BGR Enable */ 193 #define PWR_SW_EN BIT(24) /* PHY Power Switch Enable */ 194 #define PHY_M1_RST BIT(12) /* Reset PHY1 Main Channel */ 195 #define PHY_RDY BIT(16) /* PHY Main Channels Ready */ 196 #define PHY_M0_RST BIT(8) /* Reset PHY0 Main Channel */ 197 #define PHY_2LANE BIT(2) /* PHY Enable 2 lanes */ 198 #define PHY_A0_EN BIT(1) /* PHY Aux Channel0 Enable */ 199 #define PHY_M0_EN BIT(0) /* PHY Main Channel0 Enable */ 200 201 /* PLL */ 202 #define DP0_PLLCTRL 0x0900 203 #define DP1_PLLCTRL 0x0904 /* not defined in DS */ 204 #define PXL_PLLCTRL 0x0908 205 #define PLLUPDATE BIT(2) 206 #define PLLBYP BIT(1) 207 #define PLLEN BIT(0) 208 #define PXL_PLLPARAM 0x0914 209 #define IN_SEL_REFCLK (0 << 14) 210 #define SYS_PLLPARAM 0x0918 211 #define REF_FREQ_38M4 (0 << 8) /* 38.4 MHz */ 212 #define REF_FREQ_19M2 (1 << 8) /* 19.2 MHz */ 213 #define REF_FREQ_26M (2 << 8) /* 26 MHz */ 214 #define REF_FREQ_13M (3 << 8) /* 13 MHz */ 215 #define SYSCLK_SEL_LSCLK (0 << 4) 216 #define LSCLK_DIV_1 (0 << 0) 217 #define LSCLK_DIV_2 (1 << 0) 218 219 /* Test & Debug */ 220 #define TSTCTL 0x0a00 221 #define COLOR_R GENMASK(31, 24) 222 #define COLOR_G GENMASK(23, 16) 223 #define COLOR_B GENMASK(15, 8) 224 #define ENI2CFILTER BIT(4) 225 #define COLOR_BAR_MODE GENMASK(1, 0) 226 #define COLOR_BAR_MODE_BARS 2 227 #define PLL_DBG 0x0a04 228 229 static bool tc_test_pattern; 230 module_param_named(test, tc_test_pattern, bool, 0644); 231 232 struct tc_edp_link { 233 u8 dpcd[DP_RECEIVER_CAP_SIZE]; 234 unsigned int rate; 235 u8 num_lanes; 236 u8 assr; 237 bool scrambler_dis; 238 bool spread; 239 }; 240 241 struct tc_data { 242 struct device *dev; 243 struct regmap *regmap; 244 struct drm_dp_aux aux; 245 246 struct drm_bridge bridge; 247 struct drm_bridge *panel_bridge; 248 struct drm_connector connector; 249 250 /* link settings */ 251 struct tc_edp_link link; 252 253 /* current mode */ 254 struct drm_display_mode mode; 255 256 u32 rev; 257 u8 assr; 258 259 struct gpio_desc *sd_gpio; 260 struct gpio_desc *reset_gpio; 261 struct clk *refclk; 262 263 /* do we have IRQ */ 264 bool have_irq; 265 266 /* HPD pin number (0 or 1) or -ENODEV */ 267 int hpd_pin; 268 }; 269 270 static inline struct tc_data *aux_to_tc(struct drm_dp_aux *a) 271 { 272 return container_of(a, struct tc_data, aux); 273 } 274 275 static inline struct tc_data *bridge_to_tc(struct drm_bridge *b) 276 { 277 return container_of(b, struct tc_data, bridge); 278 } 279 280 static inline struct tc_data *connector_to_tc(struct drm_connector *c) 281 { 282 return container_of(c, struct tc_data, connector); 283 } 284 285 static inline int tc_poll_timeout(struct tc_data *tc, unsigned int addr, 286 unsigned int cond_mask, 287 unsigned int cond_value, 288 unsigned long sleep_us, u64 timeout_us) 289 { 290 unsigned int val; 291 292 return regmap_read_poll_timeout(tc->regmap, addr, val, 293 (val & cond_mask) == cond_value, 294 sleep_us, timeout_us); 295 } 296 297 static int tc_aux_wait_busy(struct tc_data *tc) 298 { 299 return tc_poll_timeout(tc, DP0_AUXSTATUS, AUX_BUSY, 0, 100, 100000); 300 } 301 302 static int tc_aux_write_data(struct tc_data *tc, const void *data, 303 size_t size) 304 { 305 u32 auxwdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)] = { 0 }; 306 int ret, count = ALIGN(size, sizeof(u32)); 307 308 memcpy(auxwdata, data, size); 309 310 ret = regmap_raw_write(tc->regmap, DP0_AUXWDATA(0), auxwdata, count); 311 if (ret) 312 return ret; 313 314 return size; 315 } 316 317 static int tc_aux_read_data(struct tc_data *tc, void *data, size_t size) 318 { 319 u32 auxrdata[DP_AUX_MAX_PAYLOAD_BYTES / sizeof(u32)]; 320 int ret, count = ALIGN(size, sizeof(u32)); 321 322 ret = regmap_raw_read(tc->regmap, DP0_AUXRDATA(0), auxrdata, count); 323 if (ret) 324 return ret; 325 326 memcpy(data, auxrdata, size); 327 328 return size; 329 } 330 331 static u32 tc_auxcfg0(struct drm_dp_aux_msg *msg, size_t size) 332 { 333 u32 auxcfg0 = msg->request; 334 335 if (size) 336 auxcfg0 |= FIELD_PREP(DP0_AUXCFG0_BSIZE, size - 1); 337 else 338 auxcfg0 |= DP0_AUXCFG0_ADDR_ONLY; 339 340 return auxcfg0; 341 } 342 343 static ssize_t tc_aux_transfer(struct drm_dp_aux *aux, 344 struct drm_dp_aux_msg *msg) 345 { 346 struct tc_data *tc = aux_to_tc(aux); 347 size_t size = min_t(size_t, DP_AUX_MAX_PAYLOAD_BYTES - 1, msg->size); 348 u8 request = msg->request & ~DP_AUX_I2C_MOT; 349 u32 auxstatus; 350 int ret; 351 352 ret = tc_aux_wait_busy(tc); 353 if (ret) 354 return ret; 355 356 switch (request) { 357 case DP_AUX_NATIVE_READ: 358 case DP_AUX_I2C_READ: 359 break; 360 case DP_AUX_NATIVE_WRITE: 361 case DP_AUX_I2C_WRITE: 362 if (size) { 363 ret = tc_aux_write_data(tc, msg->buffer, size); 364 if (ret < 0) 365 return ret; 366 } 367 break; 368 default: 369 return -EINVAL; 370 } 371 372 /* Store address */ 373 ret = regmap_write(tc->regmap, DP0_AUXADDR, msg->address); 374 if (ret) 375 return ret; 376 /* Start transfer */ 377 ret = regmap_write(tc->regmap, DP0_AUXCFG0, tc_auxcfg0(msg, size)); 378 if (ret) 379 return ret; 380 381 ret = tc_aux_wait_busy(tc); 382 if (ret) 383 return ret; 384 385 ret = regmap_read(tc->regmap, DP0_AUXSTATUS, &auxstatus); 386 if (ret) 387 return ret; 388 389 if (auxstatus & AUX_TIMEOUT) 390 return -ETIMEDOUT; 391 /* 392 * For some reason address-only DP_AUX_I2C_WRITE (MOT), still 393 * reports 1 byte transferred in its status. To deal we that 394 * we ignore aux_bytes field if we know that this was an 395 * address-only transfer 396 */ 397 if (size) 398 size = FIELD_GET(AUX_BYTES, auxstatus); 399 msg->reply = FIELD_GET(AUX_STATUS, auxstatus); 400 401 switch (request) { 402 case DP_AUX_NATIVE_READ: 403 case DP_AUX_I2C_READ: 404 if (size) 405 return tc_aux_read_data(tc, msg->buffer, size); 406 break; 407 } 408 409 return size; 410 } 411 412 static const char * const training_pattern1_errors[] = { 413 "No errors", 414 "Aux write error", 415 "Aux read error", 416 "Max voltage reached error", 417 "Loop counter expired error", 418 "res", "res", "res" 419 }; 420 421 static const char * const training_pattern2_errors[] = { 422 "No errors", 423 "Aux write error", 424 "Aux read error", 425 "Clock recovery failed error", 426 "Loop counter expired error", 427 "res", "res", "res" 428 }; 429 430 static u32 tc_srcctrl(struct tc_data *tc) 431 { 432 /* 433 * No training pattern, skew lane 1 data by two LSCLK cycles with 434 * respect to lane 0 data, AutoCorrect Mode = 0 435 */ 436 u32 reg = DP0_SRCCTRL_NOTP | DP0_SRCCTRL_LANESKEW | DP0_SRCCTRL_EN810B; 437 438 if (tc->link.scrambler_dis) 439 reg |= DP0_SRCCTRL_SCRMBLDIS; /* Scrambler Disabled */ 440 if (tc->link.spread) 441 reg |= DP0_SRCCTRL_SSCG; /* Spread Spectrum Enable */ 442 if (tc->link.num_lanes == 2) 443 reg |= DP0_SRCCTRL_LANES_2; /* Two Main Channel Lanes */ 444 if (tc->link.rate != 162000) 445 reg |= DP0_SRCCTRL_BW27; /* 2.7 Gbps link */ 446 return reg; 447 } 448 449 static int tc_pllupdate(struct tc_data *tc, unsigned int pllctrl) 450 { 451 int ret; 452 453 ret = regmap_write(tc->regmap, pllctrl, PLLUPDATE | PLLEN); 454 if (ret) 455 return ret; 456 457 /* Wait for PLL to lock: up to 2.09 ms, depending on refclk */ 458 usleep_range(3000, 6000); 459 460 return 0; 461 } 462 463 static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock) 464 { 465 int ret; 466 int i_pre, best_pre = 1; 467 int i_post, best_post = 1; 468 int div, best_div = 1; 469 int mul, best_mul = 1; 470 int delta, best_delta; 471 int ext_div[] = {1, 2, 3, 5, 7}; 472 int best_pixelclock = 0; 473 int vco_hi = 0; 474 u32 pxl_pllparam; 475 476 dev_dbg(tc->dev, "PLL: requested %d pixelclock, ref %d\n", pixelclock, 477 refclk); 478 best_delta = pixelclock; 479 /* Loop over all possible ext_divs, skipping invalid configurations */ 480 for (i_pre = 0; i_pre < ARRAY_SIZE(ext_div); i_pre++) { 481 /* 482 * refclk / ext_pre_div should be in the 1 to 200 MHz range. 483 * We don't allow any refclk > 200 MHz, only check lower bounds. 484 */ 485 if (refclk / ext_div[i_pre] < 1000000) 486 continue; 487 for (i_post = 0; i_post < ARRAY_SIZE(ext_div); i_post++) { 488 for (div = 1; div <= 16; div++) { 489 u32 clk; 490 u64 tmp; 491 492 tmp = pixelclock * ext_div[i_pre] * 493 ext_div[i_post] * div; 494 do_div(tmp, refclk); 495 mul = tmp; 496 497 /* Check limits */ 498 if ((mul < 1) || (mul > 128)) 499 continue; 500 501 clk = (refclk / ext_div[i_pre] / div) * mul; 502 /* 503 * refclk * mul / (ext_pre_div * pre_div) 504 * should be in the 150 to 650 MHz range 505 */ 506 if ((clk > 650000000) || (clk < 150000000)) 507 continue; 508 509 clk = clk / ext_div[i_post]; 510 delta = clk - pixelclock; 511 512 if (abs(delta) < abs(best_delta)) { 513 best_pre = i_pre; 514 best_post = i_post; 515 best_div = div; 516 best_mul = mul; 517 best_delta = delta; 518 best_pixelclock = clk; 519 } 520 } 521 } 522 } 523 if (best_pixelclock == 0) { 524 dev_err(tc->dev, "Failed to calc clock for %d pixelclock\n", 525 pixelclock); 526 return -EINVAL; 527 } 528 529 dev_dbg(tc->dev, "PLL: got %d, delta %d\n", best_pixelclock, 530 best_delta); 531 dev_dbg(tc->dev, "PLL: %d / %d / %d * %d / %d\n", refclk, 532 ext_div[best_pre], best_div, best_mul, ext_div[best_post]); 533 534 /* if VCO >= 300 MHz */ 535 if (refclk / ext_div[best_pre] / best_div * best_mul >= 300000000) 536 vco_hi = 1; 537 /* see DS */ 538 if (best_div == 16) 539 best_div = 0; 540 if (best_mul == 128) 541 best_mul = 0; 542 543 /* Power up PLL and switch to bypass */ 544 ret = regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP | PLLEN); 545 if (ret) 546 return ret; 547 548 pxl_pllparam = vco_hi << 24; /* For PLL VCO >= 300 MHz = 1 */ 549 pxl_pllparam |= ext_div[best_pre] << 20; /* External Pre-divider */ 550 pxl_pllparam |= ext_div[best_post] << 16; /* External Post-divider */ 551 pxl_pllparam |= IN_SEL_REFCLK; /* Use RefClk as PLL input */ 552 pxl_pllparam |= best_div << 8; /* Divider for PLL RefClk */ 553 pxl_pllparam |= best_mul; /* Multiplier for PLL */ 554 555 ret = regmap_write(tc->regmap, PXL_PLLPARAM, pxl_pllparam); 556 if (ret) 557 return ret; 558 559 /* Force PLL parameter update and disable bypass */ 560 return tc_pllupdate(tc, PXL_PLLCTRL); 561 } 562 563 static int tc_pxl_pll_dis(struct tc_data *tc) 564 { 565 /* Enable PLL bypass, power down PLL */ 566 return regmap_write(tc->regmap, PXL_PLLCTRL, PLLBYP); 567 } 568 569 static int tc_stream_clock_calc(struct tc_data *tc) 570 { 571 /* 572 * If the Stream clock and Link Symbol clock are 573 * asynchronous with each other, the value of M changes over 574 * time. This way of generating link clock and stream 575 * clock is called Asynchronous Clock mode. The value M 576 * must change while the value N stays constant. The 577 * value of N in this Asynchronous Clock mode must be set 578 * to 2^15 or 32,768. 579 * 580 * LSCLK = 1/10 of high speed link clock 581 * 582 * f_STRMCLK = M/N * f_LSCLK 583 * M/N = f_STRMCLK / f_LSCLK 584 * 585 */ 586 return regmap_write(tc->regmap, DP0_VIDMNGEN1, 32768); 587 } 588 589 static int tc_set_syspllparam(struct tc_data *tc) 590 { 591 unsigned long rate; 592 u32 pllparam = SYSCLK_SEL_LSCLK | LSCLK_DIV_2; 593 594 rate = clk_get_rate(tc->refclk); 595 switch (rate) { 596 case 38400000: 597 pllparam |= REF_FREQ_38M4; 598 break; 599 case 26000000: 600 pllparam |= REF_FREQ_26M; 601 break; 602 case 19200000: 603 pllparam |= REF_FREQ_19M2; 604 break; 605 case 13000000: 606 pllparam |= REF_FREQ_13M; 607 break; 608 default: 609 dev_err(tc->dev, "Invalid refclk rate: %lu Hz\n", rate); 610 return -EINVAL; 611 } 612 613 return regmap_write(tc->regmap, SYS_PLLPARAM, pllparam); 614 } 615 616 static int tc_aux_link_setup(struct tc_data *tc) 617 { 618 int ret; 619 u32 dp0_auxcfg1; 620 621 /* Setup DP-PHY / PLL */ 622 ret = tc_set_syspllparam(tc); 623 if (ret) 624 goto err; 625 626 ret = regmap_write(tc->regmap, DP_PHY_CTRL, 627 BGREN | PWR_SW_EN | PHY_A0_EN); 628 if (ret) 629 goto err; 630 /* 631 * Initially PLLs are in bypass. Force PLL parameter update, 632 * disable PLL bypass, enable PLL 633 */ 634 ret = tc_pllupdate(tc, DP0_PLLCTRL); 635 if (ret) 636 goto err; 637 638 ret = tc_pllupdate(tc, DP1_PLLCTRL); 639 if (ret) 640 goto err; 641 642 ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 100, 100000); 643 if (ret == -ETIMEDOUT) { 644 dev_err(tc->dev, "Timeout waiting for PHY to become ready"); 645 return ret; 646 } else if (ret) { 647 goto err; 648 } 649 650 /* Setup AUX link */ 651 dp0_auxcfg1 = AUX_RX_FILTER_EN; 652 dp0_auxcfg1 |= 0x06 << 8; /* Aux Bit Period Calculator Threshold */ 653 dp0_auxcfg1 |= 0x3f << 0; /* Aux Response Timeout Timer */ 654 655 ret = regmap_write(tc->regmap, DP0_AUXCFG1, dp0_auxcfg1); 656 if (ret) 657 goto err; 658 659 return 0; 660 err: 661 dev_err(tc->dev, "tc_aux_link_setup failed: %d\n", ret); 662 return ret; 663 } 664 665 static int tc_get_display_props(struct tc_data *tc) 666 { 667 u8 revision, num_lanes; 668 unsigned int rate; 669 int ret; 670 u8 reg; 671 672 /* Read DP Rx Link Capability */ 673 ret = drm_dp_dpcd_read(&tc->aux, DP_DPCD_REV, tc->link.dpcd, 674 DP_RECEIVER_CAP_SIZE); 675 if (ret < 0) 676 goto err_dpcd_read; 677 678 revision = tc->link.dpcd[DP_DPCD_REV]; 679 rate = drm_dp_max_link_rate(tc->link.dpcd); 680 num_lanes = drm_dp_max_lane_count(tc->link.dpcd); 681 682 if (rate != 162000 && rate != 270000) { 683 dev_dbg(tc->dev, "Falling to 2.7 Gbps rate\n"); 684 rate = 270000; 685 } 686 687 tc->link.rate = rate; 688 689 if (num_lanes > 2) { 690 dev_dbg(tc->dev, "Falling to 2 lanes\n"); 691 num_lanes = 2; 692 } 693 694 tc->link.num_lanes = num_lanes; 695 696 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAX_DOWNSPREAD, ®); 697 if (ret < 0) 698 goto err_dpcd_read; 699 tc->link.spread = reg & DP_MAX_DOWNSPREAD_0_5; 700 701 ret = drm_dp_dpcd_readb(&tc->aux, DP_MAIN_LINK_CHANNEL_CODING, ®); 702 if (ret < 0) 703 goto err_dpcd_read; 704 705 tc->link.scrambler_dis = false; 706 /* read assr */ 707 ret = drm_dp_dpcd_readb(&tc->aux, DP_EDP_CONFIGURATION_SET, ®); 708 if (ret < 0) 709 goto err_dpcd_read; 710 tc->link.assr = reg & DP_ALTERNATE_SCRAMBLER_RESET_ENABLE; 711 712 dev_dbg(tc->dev, "DPCD rev: %d.%d, rate: %s, lanes: %d, framing: %s\n", 713 revision >> 4, revision & 0x0f, 714 (tc->link.rate == 162000) ? "1.62Gbps" : "2.7Gbps", 715 tc->link.num_lanes, 716 drm_dp_enhanced_frame_cap(tc->link.dpcd) ? 717 "enhanced" : "default"); 718 dev_dbg(tc->dev, "Downspread: %s, scrambler: %s\n", 719 tc->link.spread ? "0.5%" : "0.0%", 720 tc->link.scrambler_dis ? "disabled" : "enabled"); 721 dev_dbg(tc->dev, "Display ASSR: %d, TC358767 ASSR: %d\n", 722 tc->link.assr, tc->assr); 723 724 return 0; 725 726 err_dpcd_read: 727 dev_err(tc->dev, "failed to read DPCD: %d\n", ret); 728 return ret; 729 } 730 731 static int tc_set_video_mode(struct tc_data *tc, 732 const struct drm_display_mode *mode) 733 { 734 int ret; 735 int vid_sync_dly; 736 int max_tu_symbol; 737 738 int left_margin = mode->htotal - mode->hsync_end; 739 int right_margin = mode->hsync_start - mode->hdisplay; 740 int hsync_len = mode->hsync_end - mode->hsync_start; 741 int upper_margin = mode->vtotal - mode->vsync_end; 742 int lower_margin = mode->vsync_start - mode->vdisplay; 743 int vsync_len = mode->vsync_end - mode->vsync_start; 744 u32 dp0_syncval; 745 u32 bits_per_pixel = 24; 746 u32 in_bw, out_bw; 747 748 /* 749 * Recommended maximum number of symbols transferred in a transfer unit: 750 * DIV_ROUND_UP((input active video bandwidth in bytes) * tu_size, 751 * (output active video bandwidth in bytes)) 752 * Must be less than tu_size. 753 */ 754 755 in_bw = mode->clock * bits_per_pixel / 8; 756 out_bw = tc->link.num_lanes * tc->link.rate; 757 max_tu_symbol = DIV_ROUND_UP(in_bw * TU_SIZE_RECOMMENDED, out_bw); 758 759 dev_dbg(tc->dev, "set mode %dx%d\n", 760 mode->hdisplay, mode->vdisplay); 761 dev_dbg(tc->dev, "H margin %d,%d sync %d\n", 762 left_margin, right_margin, hsync_len); 763 dev_dbg(tc->dev, "V margin %d,%d sync %d\n", 764 upper_margin, lower_margin, vsync_len); 765 dev_dbg(tc->dev, "total: %dx%d\n", mode->htotal, mode->vtotal); 766 767 768 /* 769 * LCD Ctl Frame Size 770 * datasheet is not clear of vsdelay in case of DPI 771 * assume we do not need any delay when DPI is a source of 772 * sync signals 773 */ 774 ret = regmap_write(tc->regmap, VPCTRL0, 775 FIELD_PREP(VSDELAY, 0) | 776 OPXLFMT_RGB888 | FRMSYNC_DISABLED | MSF_DISABLED); 777 if (ret) 778 return ret; 779 780 ret = regmap_write(tc->regmap, HTIM01, 781 FIELD_PREP(HBPR, ALIGN(left_margin, 2)) | 782 FIELD_PREP(HPW, ALIGN(hsync_len, 2))); 783 if (ret) 784 return ret; 785 786 ret = regmap_write(tc->regmap, HTIM02, 787 FIELD_PREP(HDISPR, ALIGN(mode->hdisplay, 2)) | 788 FIELD_PREP(HFPR, ALIGN(right_margin, 2))); 789 if (ret) 790 return ret; 791 792 ret = regmap_write(tc->regmap, VTIM01, 793 FIELD_PREP(VBPR, upper_margin) | 794 FIELD_PREP(VSPR, vsync_len)); 795 if (ret) 796 return ret; 797 798 ret = regmap_write(tc->regmap, VTIM02, 799 FIELD_PREP(VFPR, lower_margin) | 800 FIELD_PREP(VDISPR, mode->vdisplay)); 801 if (ret) 802 return ret; 803 804 ret = regmap_write(tc->regmap, VFUEN0, VFUEN); /* update settings */ 805 if (ret) 806 return ret; 807 808 /* Test pattern settings */ 809 ret = regmap_write(tc->regmap, TSTCTL, 810 FIELD_PREP(COLOR_R, 120) | 811 FIELD_PREP(COLOR_G, 20) | 812 FIELD_PREP(COLOR_B, 99) | 813 ENI2CFILTER | 814 FIELD_PREP(COLOR_BAR_MODE, COLOR_BAR_MODE_BARS)); 815 if (ret) 816 return ret; 817 818 /* DP Main Stream Attributes */ 819 vid_sync_dly = hsync_len + left_margin + mode->hdisplay; 820 ret = regmap_write(tc->regmap, DP0_VIDSYNCDELAY, 821 FIELD_PREP(THRESH_DLY, max_tu_symbol) | 822 FIELD_PREP(VID_SYNC_DLY, vid_sync_dly)); 823 824 ret = regmap_write(tc->regmap, DP0_TOTALVAL, 825 FIELD_PREP(H_TOTAL, mode->htotal) | 826 FIELD_PREP(V_TOTAL, mode->vtotal)); 827 if (ret) 828 return ret; 829 830 ret = regmap_write(tc->regmap, DP0_STARTVAL, 831 FIELD_PREP(H_START, left_margin + hsync_len) | 832 FIELD_PREP(V_START, upper_margin + vsync_len)); 833 if (ret) 834 return ret; 835 836 ret = regmap_write(tc->regmap, DP0_ACTIVEVAL, 837 FIELD_PREP(V_ACT, mode->vdisplay) | 838 FIELD_PREP(H_ACT, mode->hdisplay)); 839 if (ret) 840 return ret; 841 842 dp0_syncval = FIELD_PREP(VS_WIDTH, vsync_len) | 843 FIELD_PREP(HS_WIDTH, hsync_len); 844 845 if (mode->flags & DRM_MODE_FLAG_NVSYNC) 846 dp0_syncval |= SYNCVAL_VS_POL_ACTIVE_LOW; 847 848 if (mode->flags & DRM_MODE_FLAG_NHSYNC) 849 dp0_syncval |= SYNCVAL_HS_POL_ACTIVE_LOW; 850 851 ret = regmap_write(tc->regmap, DP0_SYNCVAL, dp0_syncval); 852 if (ret) 853 return ret; 854 855 ret = regmap_write(tc->regmap, DPIPXLFMT, 856 VS_POL_ACTIVE_LOW | HS_POL_ACTIVE_LOW | 857 DE_POL_ACTIVE_HIGH | SUB_CFG_TYPE_CONFIG1 | 858 DPI_BPP_RGB888); 859 if (ret) 860 return ret; 861 862 ret = regmap_write(tc->regmap, DP0_MISC, 863 FIELD_PREP(MAX_TU_SYMBOL, max_tu_symbol) | 864 FIELD_PREP(TU_SIZE, TU_SIZE_RECOMMENDED) | 865 BPC_8); 866 if (ret) 867 return ret; 868 869 return 0; 870 } 871 872 static int tc_wait_link_training(struct tc_data *tc) 873 { 874 u32 value; 875 int ret; 876 877 ret = tc_poll_timeout(tc, DP0_LTSTAT, LT_LOOPDONE, 878 LT_LOOPDONE, 500, 100000); 879 if (ret) { 880 dev_err(tc->dev, "Link training timeout waiting for LT_LOOPDONE!\n"); 881 return ret; 882 } 883 884 ret = regmap_read(tc->regmap, DP0_LTSTAT, &value); 885 if (ret) 886 return ret; 887 888 return (value >> 8) & 0x7; 889 } 890 891 static int tc_main_link_enable(struct tc_data *tc) 892 { 893 struct drm_dp_aux *aux = &tc->aux; 894 struct device *dev = tc->dev; 895 u32 dp_phy_ctrl; 896 u32 value; 897 int ret; 898 u8 tmp[DP_LINK_STATUS_SIZE]; 899 900 dev_dbg(tc->dev, "link enable\n"); 901 902 ret = regmap_read(tc->regmap, DP0CTL, &value); 903 if (ret) 904 return ret; 905 906 if (WARN_ON(value & DP_EN)) { 907 ret = regmap_write(tc->regmap, DP0CTL, 0); 908 if (ret) 909 return ret; 910 } 911 912 ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc)); 913 if (ret) 914 return ret; 915 /* SSCG and BW27 on DP1 must be set to the same as on DP0 */ 916 ret = regmap_write(tc->regmap, DP1_SRCCTRL, 917 (tc->link.spread ? DP0_SRCCTRL_SSCG : 0) | 918 ((tc->link.rate != 162000) ? DP0_SRCCTRL_BW27 : 0)); 919 if (ret) 920 return ret; 921 922 ret = tc_set_syspllparam(tc); 923 if (ret) 924 return ret; 925 926 /* Setup Main Link */ 927 dp_phy_ctrl = BGREN | PWR_SW_EN | PHY_A0_EN | PHY_M0_EN; 928 if (tc->link.num_lanes == 2) 929 dp_phy_ctrl |= PHY_2LANE; 930 931 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 932 if (ret) 933 return ret; 934 935 /* PLL setup */ 936 ret = tc_pllupdate(tc, DP0_PLLCTRL); 937 if (ret) 938 return ret; 939 940 ret = tc_pllupdate(tc, DP1_PLLCTRL); 941 if (ret) 942 return ret; 943 944 /* Reset/Enable Main Links */ 945 dp_phy_ctrl |= DP_PHY_RST | PHY_M1_RST | PHY_M0_RST; 946 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 947 usleep_range(100, 200); 948 dp_phy_ctrl &= ~(DP_PHY_RST | PHY_M1_RST | PHY_M0_RST); 949 ret = regmap_write(tc->regmap, DP_PHY_CTRL, dp_phy_ctrl); 950 951 ret = tc_poll_timeout(tc, DP_PHY_CTRL, PHY_RDY, PHY_RDY, 500, 100000); 952 if (ret) { 953 dev_err(dev, "timeout waiting for phy become ready"); 954 return ret; 955 } 956 957 /* Set misc: 8 bits per color */ 958 ret = regmap_update_bits(tc->regmap, DP0_MISC, BPC_8, BPC_8); 959 if (ret) 960 return ret; 961 962 /* 963 * ASSR mode 964 * on TC358767 side ASSR configured through strap pin 965 * seems there is no way to change this setting from SW 966 * 967 * check is tc configured for same mode 968 */ 969 if (tc->assr != tc->link.assr) { 970 dev_dbg(dev, "Trying to set display to ASSR: %d\n", 971 tc->assr); 972 /* try to set ASSR on display side */ 973 tmp[0] = tc->assr; 974 ret = drm_dp_dpcd_writeb(aux, DP_EDP_CONFIGURATION_SET, tmp[0]); 975 if (ret < 0) 976 goto err_dpcd_read; 977 /* read back */ 978 ret = drm_dp_dpcd_readb(aux, DP_EDP_CONFIGURATION_SET, tmp); 979 if (ret < 0) 980 goto err_dpcd_read; 981 982 if (tmp[0] != tc->assr) { 983 dev_dbg(dev, "Failed to switch display ASSR to %d, falling back to unscrambled mode\n", 984 tc->assr); 985 /* trying with disabled scrambler */ 986 tc->link.scrambler_dis = true; 987 } 988 } 989 990 /* Setup Link & DPRx Config for Training */ 991 tmp[0] = drm_dp_link_rate_to_bw_code(tc->link.rate); 992 tmp[1] = tc->link.num_lanes; 993 994 if (drm_dp_enhanced_frame_cap(tc->link.dpcd)) 995 tmp[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN; 996 997 ret = drm_dp_dpcd_write(aux, DP_LINK_BW_SET, tmp, 2); 998 if (ret < 0) 999 goto err_dpcd_write; 1000 1001 /* DOWNSPREAD_CTRL */ 1002 tmp[0] = tc->link.spread ? DP_SPREAD_AMP_0_5 : 0x00; 1003 /* MAIN_LINK_CHANNEL_CODING_SET */ 1004 tmp[1] = DP_SET_ANSI_8B10B; 1005 ret = drm_dp_dpcd_write(aux, DP_DOWNSPREAD_CTRL, tmp, 2); 1006 if (ret < 0) 1007 goto err_dpcd_write; 1008 1009 /* Reset voltage-swing & pre-emphasis */ 1010 tmp[0] = tmp[1] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | 1011 DP_TRAIN_PRE_EMPH_LEVEL_0; 1012 ret = drm_dp_dpcd_write(aux, DP_TRAINING_LANE0_SET, tmp, 2); 1013 if (ret < 0) 1014 goto err_dpcd_write; 1015 1016 /* Clock-Recovery */ 1017 1018 /* Set DPCD 0x102 for Training Pattern 1 */ 1019 ret = regmap_write(tc->regmap, DP0_SNKLTCTRL, 1020 DP_LINK_SCRAMBLING_DISABLE | 1021 DP_TRAINING_PATTERN_1); 1022 if (ret) 1023 return ret; 1024 1025 ret = regmap_write(tc->regmap, DP0_LTLOOPCTRL, 1026 (15 << 28) | /* Defer Iteration Count */ 1027 (15 << 24) | /* Loop Iteration Count */ 1028 (0xd << 0)); /* Loop Timer Delay */ 1029 if (ret) 1030 return ret; 1031 1032 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 1033 tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS | 1034 DP0_SRCCTRL_AUTOCORRECT | 1035 DP0_SRCCTRL_TP1); 1036 if (ret) 1037 return ret; 1038 1039 /* Enable DP0 to start Link Training */ 1040 ret = regmap_write(tc->regmap, DP0CTL, 1041 (drm_dp_enhanced_frame_cap(tc->link.dpcd) ? 1042 EF_EN : 0) | DP_EN); 1043 if (ret) 1044 return ret; 1045 1046 /* wait */ 1047 1048 ret = tc_wait_link_training(tc); 1049 if (ret < 0) 1050 return ret; 1051 1052 if (ret) { 1053 dev_err(tc->dev, "Link training phase 1 failed: %s\n", 1054 training_pattern1_errors[ret]); 1055 return -ENODEV; 1056 } 1057 1058 /* Channel Equalization */ 1059 1060 /* Set DPCD 0x102 for Training Pattern 2 */ 1061 ret = regmap_write(tc->regmap, DP0_SNKLTCTRL, 1062 DP_LINK_SCRAMBLING_DISABLE | 1063 DP_TRAINING_PATTERN_2); 1064 if (ret) 1065 return ret; 1066 1067 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 1068 tc_srcctrl(tc) | DP0_SRCCTRL_SCRMBLDIS | 1069 DP0_SRCCTRL_AUTOCORRECT | 1070 DP0_SRCCTRL_TP2); 1071 if (ret) 1072 return ret; 1073 1074 /* wait */ 1075 ret = tc_wait_link_training(tc); 1076 if (ret < 0) 1077 return ret; 1078 1079 if (ret) { 1080 dev_err(tc->dev, "Link training phase 2 failed: %s\n", 1081 training_pattern2_errors[ret]); 1082 return -ENODEV; 1083 } 1084 1085 /* 1086 * Toshiba's documentation suggests to first clear DPCD 0x102, then 1087 * clear the training pattern bit in DP0_SRCCTRL. Testing shows 1088 * that the link sometimes drops if those steps are done in that order, 1089 * but if the steps are done in reverse order, the link stays up. 1090 * 1091 * So we do the steps differently than documented here. 1092 */ 1093 1094 /* Clear Training Pattern, set AutoCorrect Mode = 1 */ 1095 ret = regmap_write(tc->regmap, DP0_SRCCTRL, tc_srcctrl(tc) | 1096 DP0_SRCCTRL_AUTOCORRECT); 1097 if (ret) 1098 return ret; 1099 1100 /* Clear DPCD 0x102 */ 1101 /* Note: Can Not use DP0_SNKLTCTRL (0x06E4) short cut */ 1102 tmp[0] = tc->link.scrambler_dis ? DP_LINK_SCRAMBLING_DISABLE : 0x00; 1103 ret = drm_dp_dpcd_writeb(aux, DP_TRAINING_PATTERN_SET, tmp[0]); 1104 if (ret < 0) 1105 goto err_dpcd_write; 1106 1107 /* Check link status */ 1108 ret = drm_dp_dpcd_read_link_status(aux, tmp); 1109 if (ret < 0) 1110 goto err_dpcd_read; 1111 1112 ret = 0; 1113 1114 value = tmp[0] & DP_CHANNEL_EQ_BITS; 1115 1116 if (value != DP_CHANNEL_EQ_BITS) { 1117 dev_err(tc->dev, "Lane 0 failed: %x\n", value); 1118 ret = -ENODEV; 1119 } 1120 1121 if (tc->link.num_lanes == 2) { 1122 value = (tmp[0] >> 4) & DP_CHANNEL_EQ_BITS; 1123 1124 if (value != DP_CHANNEL_EQ_BITS) { 1125 dev_err(tc->dev, "Lane 1 failed: %x\n", value); 1126 ret = -ENODEV; 1127 } 1128 1129 if (!(tmp[2] & DP_INTERLANE_ALIGN_DONE)) { 1130 dev_err(tc->dev, "Interlane align failed\n"); 1131 ret = -ENODEV; 1132 } 1133 } 1134 1135 if (ret) { 1136 dev_err(dev, "0x0202 LANE0_1_STATUS: 0x%02x\n", tmp[0]); 1137 dev_err(dev, "0x0203 LANE2_3_STATUS 0x%02x\n", tmp[1]); 1138 dev_err(dev, "0x0204 LANE_ALIGN_STATUS_UPDATED: 0x%02x\n", tmp[2]); 1139 dev_err(dev, "0x0205 SINK_STATUS: 0x%02x\n", tmp[3]); 1140 dev_err(dev, "0x0206 ADJUST_REQUEST_LANE0_1: 0x%02x\n", tmp[4]); 1141 dev_err(dev, "0x0207 ADJUST_REQUEST_LANE2_3: 0x%02x\n", tmp[5]); 1142 return ret; 1143 } 1144 1145 return 0; 1146 err_dpcd_read: 1147 dev_err(tc->dev, "Failed to read DPCD: %d\n", ret); 1148 return ret; 1149 err_dpcd_write: 1150 dev_err(tc->dev, "Failed to write DPCD: %d\n", ret); 1151 return ret; 1152 } 1153 1154 static int tc_main_link_disable(struct tc_data *tc) 1155 { 1156 int ret; 1157 1158 dev_dbg(tc->dev, "link disable\n"); 1159 1160 ret = regmap_write(tc->regmap, DP0_SRCCTRL, 0); 1161 if (ret) 1162 return ret; 1163 1164 return regmap_write(tc->regmap, DP0CTL, 0); 1165 } 1166 1167 static int tc_stream_enable(struct tc_data *tc) 1168 { 1169 int ret; 1170 u32 value; 1171 1172 dev_dbg(tc->dev, "enable video stream\n"); 1173 1174 /* PXL PLL setup */ 1175 if (tc_test_pattern) { 1176 ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk), 1177 1000 * tc->mode.clock); 1178 if (ret) 1179 return ret; 1180 } 1181 1182 ret = tc_set_video_mode(tc, &tc->mode); 1183 if (ret) 1184 return ret; 1185 1186 /* Set M/N */ 1187 ret = tc_stream_clock_calc(tc); 1188 if (ret) 1189 return ret; 1190 1191 value = VID_MN_GEN | DP_EN; 1192 if (drm_dp_enhanced_frame_cap(tc->link.dpcd)) 1193 value |= EF_EN; 1194 ret = regmap_write(tc->regmap, DP0CTL, value); 1195 if (ret) 1196 return ret; 1197 /* 1198 * VID_EN assertion should be delayed by at least N * LSCLK 1199 * cycles from the time VID_MN_GEN is enabled in order to 1200 * generate stable values for VID_M. LSCLK is 270 MHz or 1201 * 162 MHz, VID_N is set to 32768 in tc_stream_clock_calc(), 1202 * so a delay of at least 203 us should suffice. 1203 */ 1204 usleep_range(500, 1000); 1205 value |= VID_EN; 1206 ret = regmap_write(tc->regmap, DP0CTL, value); 1207 if (ret) 1208 return ret; 1209 /* Set input interface */ 1210 value = DP0_AUDSRC_NO_INPUT; 1211 if (tc_test_pattern) 1212 value |= DP0_VIDSRC_COLOR_BAR; 1213 else 1214 value |= DP0_VIDSRC_DPI_RX; 1215 ret = regmap_write(tc->regmap, SYSCTRL, value); 1216 if (ret) 1217 return ret; 1218 1219 return 0; 1220 } 1221 1222 static int tc_stream_disable(struct tc_data *tc) 1223 { 1224 int ret; 1225 1226 dev_dbg(tc->dev, "disable video stream\n"); 1227 1228 ret = regmap_update_bits(tc->regmap, DP0CTL, VID_EN, 0); 1229 if (ret) 1230 return ret; 1231 1232 tc_pxl_pll_dis(tc); 1233 1234 return 0; 1235 } 1236 1237 static void tc_bridge_enable(struct drm_bridge *bridge) 1238 { 1239 struct tc_data *tc = bridge_to_tc(bridge); 1240 int ret; 1241 1242 ret = tc_get_display_props(tc); 1243 if (ret < 0) { 1244 dev_err(tc->dev, "failed to read display props: %d\n", ret); 1245 return; 1246 } 1247 1248 ret = tc_main_link_enable(tc); 1249 if (ret < 0) { 1250 dev_err(tc->dev, "main link enable error: %d\n", ret); 1251 return; 1252 } 1253 1254 ret = tc_stream_enable(tc); 1255 if (ret < 0) { 1256 dev_err(tc->dev, "main link stream start error: %d\n", ret); 1257 tc_main_link_disable(tc); 1258 return; 1259 } 1260 } 1261 1262 static void tc_bridge_disable(struct drm_bridge *bridge) 1263 { 1264 struct tc_data *tc = bridge_to_tc(bridge); 1265 int ret; 1266 1267 ret = tc_stream_disable(tc); 1268 if (ret < 0) 1269 dev_err(tc->dev, "main link stream stop error: %d\n", ret); 1270 1271 ret = tc_main_link_disable(tc); 1272 if (ret < 0) 1273 dev_err(tc->dev, "main link disable error: %d\n", ret); 1274 } 1275 1276 static bool tc_bridge_mode_fixup(struct drm_bridge *bridge, 1277 const struct drm_display_mode *mode, 1278 struct drm_display_mode *adj) 1279 { 1280 /* Fixup sync polarities, both hsync and vsync are active low */ 1281 adj->flags = mode->flags; 1282 adj->flags |= (DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC); 1283 adj->flags &= ~(DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC); 1284 1285 return true; 1286 } 1287 1288 static enum drm_mode_status tc_mode_valid(struct drm_bridge *bridge, 1289 const struct drm_display_info *info, 1290 const struct drm_display_mode *mode) 1291 { 1292 struct tc_data *tc = bridge_to_tc(bridge); 1293 u32 req, avail; 1294 u32 bits_per_pixel = 24; 1295 1296 /* DPI interface clock limitation: upto 154 MHz */ 1297 if (mode->clock > 154000) 1298 return MODE_CLOCK_HIGH; 1299 1300 req = mode->clock * bits_per_pixel / 8; 1301 avail = tc->link.num_lanes * tc->link.rate; 1302 1303 if (req > avail) 1304 return MODE_BAD; 1305 1306 return MODE_OK; 1307 } 1308 1309 static void tc_bridge_mode_set(struct drm_bridge *bridge, 1310 const struct drm_display_mode *mode, 1311 const struct drm_display_mode *adj) 1312 { 1313 struct tc_data *tc = bridge_to_tc(bridge); 1314 1315 tc->mode = *mode; 1316 } 1317 1318 static struct edid *tc_get_edid(struct drm_bridge *bridge, 1319 struct drm_connector *connector) 1320 { 1321 struct tc_data *tc = bridge_to_tc(bridge); 1322 1323 return drm_get_edid(connector, &tc->aux.ddc); 1324 } 1325 1326 static int tc_connector_get_modes(struct drm_connector *connector) 1327 { 1328 struct tc_data *tc = connector_to_tc(connector); 1329 int num_modes; 1330 struct edid *edid; 1331 int ret; 1332 1333 ret = tc_get_display_props(tc); 1334 if (ret < 0) { 1335 dev_err(tc->dev, "failed to read display props: %d\n", ret); 1336 return 0; 1337 } 1338 1339 if (tc->panel_bridge) { 1340 num_modes = drm_bridge_get_modes(tc->panel_bridge, connector); 1341 if (num_modes > 0) 1342 return num_modes; 1343 } 1344 1345 edid = tc_get_edid(&tc->bridge, connector); 1346 num_modes = drm_add_edid_modes(connector, edid); 1347 kfree(edid); 1348 1349 return num_modes; 1350 } 1351 1352 static const struct drm_connector_helper_funcs tc_connector_helper_funcs = { 1353 .get_modes = tc_connector_get_modes, 1354 }; 1355 1356 static enum drm_connector_status tc_bridge_detect(struct drm_bridge *bridge) 1357 { 1358 struct tc_data *tc = bridge_to_tc(bridge); 1359 bool conn; 1360 u32 val; 1361 int ret; 1362 1363 ret = regmap_read(tc->regmap, GPIOI, &val); 1364 if (ret) 1365 return connector_status_unknown; 1366 1367 conn = val & BIT(tc->hpd_pin); 1368 1369 if (conn) 1370 return connector_status_connected; 1371 else 1372 return connector_status_disconnected; 1373 } 1374 1375 static enum drm_connector_status 1376 tc_connector_detect(struct drm_connector *connector, bool force) 1377 { 1378 struct tc_data *tc = connector_to_tc(connector); 1379 1380 if (tc->hpd_pin >= 0) 1381 return tc_bridge_detect(&tc->bridge); 1382 1383 if (tc->panel_bridge) 1384 return connector_status_connected; 1385 else 1386 return connector_status_unknown; 1387 } 1388 1389 static const struct drm_connector_funcs tc_connector_funcs = { 1390 .detect = tc_connector_detect, 1391 .fill_modes = drm_helper_probe_single_connector_modes, 1392 .destroy = drm_connector_cleanup, 1393 .reset = drm_atomic_helper_connector_reset, 1394 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, 1395 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, 1396 }; 1397 1398 static int tc_bridge_attach(struct drm_bridge *bridge, 1399 enum drm_bridge_attach_flags flags) 1400 { 1401 u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24; 1402 struct tc_data *tc = bridge_to_tc(bridge); 1403 struct drm_device *drm = bridge->dev; 1404 int ret; 1405 1406 if (tc->panel_bridge) { 1407 /* If a connector is required then this driver shall create it */ 1408 ret = drm_bridge_attach(tc->bridge.encoder, tc->panel_bridge, 1409 &tc->bridge, flags | DRM_BRIDGE_ATTACH_NO_CONNECTOR); 1410 if (ret) 1411 return ret; 1412 } 1413 1414 if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) 1415 return 0; 1416 1417 tc->aux.drm_dev = drm; 1418 ret = drm_dp_aux_register(&tc->aux); 1419 if (ret < 0) 1420 return ret; 1421 1422 /* Create DP/eDP connector */ 1423 drm_connector_helper_add(&tc->connector, &tc_connector_helper_funcs); 1424 ret = drm_connector_init(drm, &tc->connector, &tc_connector_funcs, tc->bridge.type); 1425 if (ret) 1426 goto aux_unregister; 1427 1428 /* Don't poll if don't have HPD connected */ 1429 if (tc->hpd_pin >= 0) { 1430 if (tc->have_irq) 1431 tc->connector.polled = DRM_CONNECTOR_POLL_HPD; 1432 else 1433 tc->connector.polled = DRM_CONNECTOR_POLL_CONNECT | 1434 DRM_CONNECTOR_POLL_DISCONNECT; 1435 } 1436 1437 drm_display_info_set_bus_formats(&tc->connector.display_info, 1438 &bus_format, 1); 1439 tc->connector.display_info.bus_flags = 1440 DRM_BUS_FLAG_DE_HIGH | 1441 DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE | 1442 DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE; 1443 drm_connector_attach_encoder(&tc->connector, tc->bridge.encoder); 1444 1445 return 0; 1446 aux_unregister: 1447 drm_dp_aux_unregister(&tc->aux); 1448 return ret; 1449 } 1450 1451 static void tc_bridge_detach(struct drm_bridge *bridge) 1452 { 1453 drm_dp_aux_unregister(&bridge_to_tc(bridge)->aux); 1454 } 1455 1456 static const struct drm_bridge_funcs tc_bridge_funcs = { 1457 .attach = tc_bridge_attach, 1458 .detach = tc_bridge_detach, 1459 .mode_valid = tc_mode_valid, 1460 .mode_set = tc_bridge_mode_set, 1461 .enable = tc_bridge_enable, 1462 .disable = tc_bridge_disable, 1463 .mode_fixup = tc_bridge_mode_fixup, 1464 .detect = tc_bridge_detect, 1465 .get_edid = tc_get_edid, 1466 }; 1467 1468 static bool tc_readable_reg(struct device *dev, unsigned int reg) 1469 { 1470 return reg != SYSCTRL; 1471 } 1472 1473 static const struct regmap_range tc_volatile_ranges[] = { 1474 regmap_reg_range(DP0_AUXWDATA(0), DP0_AUXSTATUS), 1475 regmap_reg_range(DP0_LTSTAT, DP0_SNKLTCHGREQ), 1476 regmap_reg_range(DP_PHY_CTRL, DP_PHY_CTRL), 1477 regmap_reg_range(DP0_PLLCTRL, PXL_PLLCTRL), 1478 regmap_reg_range(VFUEN0, VFUEN0), 1479 regmap_reg_range(INTSTS_G, INTSTS_G), 1480 regmap_reg_range(GPIOI, GPIOI), 1481 }; 1482 1483 static const struct regmap_access_table tc_volatile_table = { 1484 .yes_ranges = tc_volatile_ranges, 1485 .n_yes_ranges = ARRAY_SIZE(tc_volatile_ranges), 1486 }; 1487 1488 static bool tc_writeable_reg(struct device *dev, unsigned int reg) 1489 { 1490 return (reg != TC_IDREG) && 1491 (reg != DP0_LTSTAT) && 1492 (reg != DP0_SNKLTCHGREQ); 1493 } 1494 1495 static const struct regmap_config tc_regmap_config = { 1496 .name = "tc358767", 1497 .reg_bits = 16, 1498 .val_bits = 32, 1499 .reg_stride = 4, 1500 .max_register = PLL_DBG, 1501 .cache_type = REGCACHE_RBTREE, 1502 .readable_reg = tc_readable_reg, 1503 .volatile_table = &tc_volatile_table, 1504 .writeable_reg = tc_writeable_reg, 1505 .reg_format_endian = REGMAP_ENDIAN_BIG, 1506 .val_format_endian = REGMAP_ENDIAN_LITTLE, 1507 }; 1508 1509 static irqreturn_t tc_irq_handler(int irq, void *arg) 1510 { 1511 struct tc_data *tc = arg; 1512 u32 val; 1513 int r; 1514 1515 r = regmap_read(tc->regmap, INTSTS_G, &val); 1516 if (r) 1517 return IRQ_NONE; 1518 1519 if (!val) 1520 return IRQ_NONE; 1521 1522 if (val & INT_SYSERR) { 1523 u32 stat = 0; 1524 1525 regmap_read(tc->regmap, SYSSTAT, &stat); 1526 1527 dev_err(tc->dev, "syserr %x\n", stat); 1528 } 1529 1530 if (tc->hpd_pin >= 0 && tc->bridge.dev) { 1531 /* 1532 * H is triggered when the GPIO goes high. 1533 * 1534 * LC is triggered when the GPIO goes low and stays low for 1535 * the duration of LCNT 1536 */ 1537 bool h = val & INT_GPIO_H(tc->hpd_pin); 1538 bool lc = val & INT_GPIO_LC(tc->hpd_pin); 1539 1540 dev_dbg(tc->dev, "GPIO%d: %s %s\n", tc->hpd_pin, 1541 h ? "H" : "", lc ? "LC" : ""); 1542 1543 if (h || lc) 1544 drm_kms_helper_hotplug_event(tc->bridge.dev); 1545 } 1546 1547 regmap_write(tc->regmap, INTSTS_G, val); 1548 1549 return IRQ_HANDLED; 1550 } 1551 1552 static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id) 1553 { 1554 struct device *dev = &client->dev; 1555 struct drm_panel *panel; 1556 struct tc_data *tc; 1557 int ret; 1558 1559 tc = devm_kzalloc(dev, sizeof(*tc), GFP_KERNEL); 1560 if (!tc) 1561 return -ENOMEM; 1562 1563 tc->dev = dev; 1564 1565 /* port@2 is the output port */ 1566 ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, NULL); 1567 if (ret && ret != -ENODEV) 1568 return ret; 1569 1570 if (panel) { 1571 struct drm_bridge *panel_bridge; 1572 1573 panel_bridge = devm_drm_panel_bridge_add(dev, panel); 1574 if (IS_ERR(panel_bridge)) 1575 return PTR_ERR(panel_bridge); 1576 1577 tc->panel_bridge = panel_bridge; 1578 tc->bridge.type = DRM_MODE_CONNECTOR_eDP; 1579 } else { 1580 tc->bridge.type = DRM_MODE_CONNECTOR_DisplayPort; 1581 } 1582 1583 /* Shut down GPIO is optional */ 1584 tc->sd_gpio = devm_gpiod_get_optional(dev, "shutdown", GPIOD_OUT_HIGH); 1585 if (IS_ERR(tc->sd_gpio)) 1586 return PTR_ERR(tc->sd_gpio); 1587 1588 if (tc->sd_gpio) { 1589 gpiod_set_value_cansleep(tc->sd_gpio, 0); 1590 usleep_range(5000, 10000); 1591 } 1592 1593 /* Reset GPIO is optional */ 1594 tc->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1595 if (IS_ERR(tc->reset_gpio)) 1596 return PTR_ERR(tc->reset_gpio); 1597 1598 if (tc->reset_gpio) { 1599 gpiod_set_value_cansleep(tc->reset_gpio, 1); 1600 usleep_range(5000, 10000); 1601 } 1602 1603 tc->refclk = devm_clk_get(dev, "ref"); 1604 if (IS_ERR(tc->refclk)) { 1605 ret = PTR_ERR(tc->refclk); 1606 dev_err(dev, "Failed to get refclk: %d\n", ret); 1607 return ret; 1608 } 1609 1610 tc->regmap = devm_regmap_init_i2c(client, &tc_regmap_config); 1611 if (IS_ERR(tc->regmap)) { 1612 ret = PTR_ERR(tc->regmap); 1613 dev_err(dev, "Failed to initialize regmap: %d\n", ret); 1614 return ret; 1615 } 1616 1617 ret = of_property_read_u32(dev->of_node, "toshiba,hpd-pin", 1618 &tc->hpd_pin); 1619 if (ret) { 1620 tc->hpd_pin = -ENODEV; 1621 } else { 1622 if (tc->hpd_pin < 0 || tc->hpd_pin > 1) { 1623 dev_err(dev, "failed to parse HPD number\n"); 1624 return ret; 1625 } 1626 } 1627 1628 if (client->irq > 0) { 1629 /* enable SysErr */ 1630 regmap_write(tc->regmap, INTCTL_G, INT_SYSERR); 1631 1632 ret = devm_request_threaded_irq(dev, client->irq, 1633 NULL, tc_irq_handler, 1634 IRQF_ONESHOT, 1635 "tc358767-irq", tc); 1636 if (ret) { 1637 dev_err(dev, "failed to register dp interrupt\n"); 1638 return ret; 1639 } 1640 1641 tc->have_irq = true; 1642 } 1643 1644 ret = regmap_read(tc->regmap, TC_IDREG, &tc->rev); 1645 if (ret) { 1646 dev_err(tc->dev, "can not read device ID: %d\n", ret); 1647 return ret; 1648 } 1649 1650 if ((tc->rev != 0x6601) && (tc->rev != 0x6603)) { 1651 dev_err(tc->dev, "invalid device ID: 0x%08x\n", tc->rev); 1652 return -EINVAL; 1653 } 1654 1655 tc->assr = (tc->rev == 0x6601); /* Enable ASSR for eDP panels */ 1656 1657 if (!tc->reset_gpio) { 1658 /* 1659 * If the reset pin isn't present, do a software reset. It isn't 1660 * as thorough as the hardware reset, as we can't reset the I2C 1661 * communication block for obvious reasons, but it's getting the 1662 * chip into a defined state. 1663 */ 1664 regmap_update_bits(tc->regmap, SYSRSTENB, 1665 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP, 1666 0); 1667 regmap_update_bits(tc->regmap, SYSRSTENB, 1668 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP, 1669 ENBLCD0 | ENBBM | ENBDSIRX | ENBREG | ENBHDCP); 1670 usleep_range(5000, 10000); 1671 } 1672 1673 if (tc->hpd_pin >= 0) { 1674 u32 lcnt_reg = tc->hpd_pin == 0 ? INT_GP0_LCNT : INT_GP1_LCNT; 1675 u32 h_lc = INT_GPIO_H(tc->hpd_pin) | INT_GPIO_LC(tc->hpd_pin); 1676 1677 /* Set LCNT to 2ms */ 1678 regmap_write(tc->regmap, lcnt_reg, 1679 clk_get_rate(tc->refclk) * 2 / 1000); 1680 /* We need the "alternate" mode for HPD */ 1681 regmap_write(tc->regmap, GPIOM, BIT(tc->hpd_pin)); 1682 1683 if (tc->have_irq) { 1684 /* enable H & LC */ 1685 regmap_update_bits(tc->regmap, INTCTL_G, h_lc, h_lc); 1686 } 1687 } 1688 1689 ret = tc_aux_link_setup(tc); 1690 if (ret) 1691 return ret; 1692 1693 /* Register DP AUX channel */ 1694 tc->aux.name = "TC358767 AUX i2c adapter"; 1695 tc->aux.dev = tc->dev; 1696 tc->aux.transfer = tc_aux_transfer; 1697 drm_dp_aux_init(&tc->aux); 1698 1699 tc->bridge.funcs = &tc_bridge_funcs; 1700 if (tc->hpd_pin >= 0) 1701 tc->bridge.ops |= DRM_BRIDGE_OP_DETECT; 1702 tc->bridge.ops |= DRM_BRIDGE_OP_EDID; 1703 1704 tc->bridge.of_node = dev->of_node; 1705 drm_bridge_add(&tc->bridge); 1706 1707 i2c_set_clientdata(client, tc); 1708 1709 return 0; 1710 } 1711 1712 static int tc_remove(struct i2c_client *client) 1713 { 1714 struct tc_data *tc = i2c_get_clientdata(client); 1715 1716 drm_bridge_remove(&tc->bridge); 1717 1718 return 0; 1719 } 1720 1721 static const struct i2c_device_id tc358767_i2c_ids[] = { 1722 { "tc358767", 0 }, 1723 { } 1724 }; 1725 MODULE_DEVICE_TABLE(i2c, tc358767_i2c_ids); 1726 1727 static const struct of_device_id tc358767_of_ids[] = { 1728 { .compatible = "toshiba,tc358767", }, 1729 { } 1730 }; 1731 MODULE_DEVICE_TABLE(of, tc358767_of_ids); 1732 1733 static struct i2c_driver tc358767_driver = { 1734 .driver = { 1735 .name = "tc358767", 1736 .of_match_table = tc358767_of_ids, 1737 }, 1738 .id_table = tc358767_i2c_ids, 1739 .probe = tc_probe, 1740 .remove = tc_remove, 1741 }; 1742 module_i2c_driver(tc358767_driver); 1743 1744 MODULE_AUTHOR("Andrey Gusakov <andrey.gusakov@cogentembedded.com>"); 1745 MODULE_DESCRIPTION("tc358767 eDP encoder driver"); 1746 MODULE_LICENSE("GPL"); 1747