1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2020 Amarula Solutions(India) 4 * Author: Jagan Teki <jagan@amarulasolutions.com> 5 */ 6 7 #include <drm/drm_atomic_helper.h> 8 #include <drm/drm_of.h> 9 #include <drm/drm_print.h> 10 #include <drm/drm_mipi_dsi.h> 11 12 #include <linux/bitfield.h> 13 #include <linux/bits.h> 14 #include <linux/clk.h> 15 #include <linux/delay.h> 16 #include <linux/gpio/consumer.h> 17 #include <linux/i2c.h> 18 #include <linux/media-bus-format.h> 19 #include <linux/module.h> 20 #include <linux/of_device.h> 21 #include <linux/regmap.h> 22 #include <linux/regulator/consumer.h> 23 24 #define VENDOR_ID 0x00 25 #define DEVICE_ID_H 0x01 26 #define DEVICE_ID_L 0x02 27 #define VERSION_ID 0x03 28 #define FIRMWARE_VERSION 0x08 29 #define CONFIG_FINISH 0x09 30 #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */ 31 #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */ 32 #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */ 33 #define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4) 34 #define CLK_PHASE_0 0 35 #define CLK_PHASE_1_4 1 36 #define CLK_PHASE_1_2 2 37 #define CLK_PHASE_3_4 3 38 #define RGB_DRV(n) (0x18 + ((n) & 0x3)) /* 0..3 */ 39 #define RGB_DLY(n) (0x1c + ((n) & 0x1)) /* 0..1 */ 40 #define RGB_TEST_CTRL 0x1e 41 #define ATE_PLL_EN 0x1f 42 #define HACTIVE_LI 0x20 43 #define VACTIVE_LI 0x21 44 #define VACTIVE_HACTIVE_HI 0x22 45 #define HFP_LI 0x23 46 #define HSYNC_LI 0x24 47 #define HBP_LI 0x25 48 #define HFP_HSW_HBP_HI 0x26 49 #define HFP_HSW_HBP_HI_HFP(n) (((n) & 0x300) >> 4) 50 #define HFP_HSW_HBP_HI_HS(n) (((n) & 0x300) >> 6) 51 #define HFP_HSW_HBP_HI_HBP(n) (((n) & 0x300) >> 8) 52 #define VFP 0x27 53 #define VSYNC 0x28 54 #define VBP 0x29 55 #define BIST_POL 0x2a 56 #define BIST_POL_BIST_MODE(n) (((n) & 0xf) << 4) 57 #define BIST_POL_BIST_GEN BIT(3) 58 #define BIST_POL_HSYNC_POL BIT(2) 59 #define BIST_POL_VSYNC_POL BIT(1) 60 #define BIST_POL_DE_POL BIT(0) 61 #define BIST_RED 0x2b 62 #define BIST_GREEN 0x2c 63 #define BIST_BLUE 0x2d 64 #define BIST_CHESS_X 0x2e 65 #define BIST_CHESS_Y 0x2f 66 #define BIST_CHESS_XY_H 0x30 67 #define BIST_FRAME_TIME_L 0x31 68 #define BIST_FRAME_TIME_H 0x32 69 #define FIFO_MAX_ADDR_LOW 0x33 70 #define SYNC_EVENT_DLY 0x34 71 #define HSW_MIN 0x35 72 #define HFP_MIN 0x36 73 #define LOGIC_RST_NUM 0x37 74 #define OSC_CTRL(n) (0x48 + ((n) & 0x7)) /* 0..5 */ 75 #define BG_CTRL 0x4e 76 #define LDO_PLL 0x4f 77 #define PLL_CTRL(n) (0x50 + ((n) & 0xf)) /* 0..15 */ 78 #define PLL_CTRL_6_EXTERNAL 0x90 79 #define PLL_CTRL_6_MIPI_CLK 0x92 80 #define PLL_CTRL_6_INTERNAL 0x93 81 #define PLL_REM(n) (0x60 + ((n) & 0x3)) /* 0..2 */ 82 #define PLL_DIV(n) (0x63 + ((n) & 0x3)) /* 0..2 */ 83 #define PLL_FRAC(n) (0x66 + ((n) & 0x3)) /* 0..2 */ 84 #define PLL_INT(n) (0x69 + ((n) & 0x1)) /* 0..1 */ 85 #define PLL_REF_DIV 0x6b 86 #define PLL_REF_DIV_P(n) ((n) & 0xf) 87 #define PLL_REF_DIV_Pe BIT(4) 88 #define PLL_REF_DIV_S(n) (((n) & 0x7) << 5) 89 #define PLL_SSC_P(n) (0x6c + ((n) & 0x3)) /* 0..2 */ 90 #define PLL_SSC_STEP(n) (0x6f + ((n) & 0x3)) /* 0..2 */ 91 #define PLL_SSC_OFFSET(n) (0x72 + ((n) & 0x3)) /* 0..3 */ 92 #define GPIO_OEN 0x79 93 #define MIPI_CFG_PW 0x7a 94 #define MIPI_CFG_PW_CONFIG_DSI 0xc1 95 #define MIPI_CFG_PW_CONFIG_I2C 0x3e 96 #define GPIO_SEL(n) (0x7b + ((n) & 0x1)) /* 0..1 */ 97 #define IRQ_SEL 0x7d 98 #define DBG_SEL 0x7e 99 #define DBG_SIGNAL 0x7f 100 #define MIPI_ERR_VECTOR_L 0x80 101 #define MIPI_ERR_VECTOR_H 0x81 102 #define MIPI_ERR_VECTOR_EN_L 0x82 103 #define MIPI_ERR_VECTOR_EN_H 0x83 104 #define MIPI_MAX_SIZE_L 0x84 105 #define MIPI_MAX_SIZE_H 0x85 106 #define DSI_CTRL 0x86 107 #define DSI_CTRL_UNKNOWN 0x28 108 #define DSI_CTRL_DSI_LANES(n) ((n) & 0x3) 109 #define MIPI_PN_SWAP 0x87 110 #define MIPI_PN_SWAP_CLK BIT(4) 111 #define MIPI_PN_SWAP_D(n) BIT((n) & 0x3) 112 #define MIPI_SOT_SYNC_BIT(n) (0x88 + ((n) & 0x1)) /* 0..1 */ 113 #define MIPI_ULPS_CTRL 0x8a 114 #define MIPI_CLK_CHK_VAR 0x8e 115 #define MIPI_CLK_CHK_INI 0x8f 116 #define MIPI_T_TERM_EN 0x90 117 #define MIPI_T_HS_SETTLE 0x91 118 #define MIPI_T_TA_SURE_PRE 0x92 119 #define MIPI_T_LPX_SET 0x94 120 #define MIPI_T_CLK_MISS 0x95 121 #define MIPI_INIT_TIME_L 0x96 122 #define MIPI_INIT_TIME_H 0x97 123 #define MIPI_T_CLK_TERM_EN 0x99 124 #define MIPI_T_CLK_SETTLE 0x9a 125 #define MIPI_TO_HS_RX_L 0x9e 126 #define MIPI_TO_HS_RX_H 0x9f 127 #define MIPI_PHY(n) (0xa0 + ((n) & 0x7)) /* 0..5 */ 128 #define MIPI_PD_RX 0xb0 129 #define MIPI_PD_TERM 0xb1 130 #define MIPI_PD_HSRX 0xb2 131 #define MIPI_PD_LPTX 0xb3 132 #define MIPI_PD_LPRX 0xb4 133 #define MIPI_PD_CK_LANE 0xb5 134 #define MIPI_FORCE_0 0xb6 135 #define MIPI_RST_CTRL 0xb7 136 #define MIPI_RST_NUM 0xb8 137 #define MIPI_DBG_SET(n) (0xc0 + ((n) & 0xf)) /* 0..9 */ 138 #define MIPI_DBG_SEL 0xe0 139 #define MIPI_DBG_DATA 0xe1 140 #define MIPI_ATE_TEST_SEL 0xe2 141 #define MIPI_ATE_STATUS(n) (0xe3 + ((n) & 0x1)) /* 0..1 */ 142 143 struct chipone { 144 struct device *dev; 145 struct regmap *regmap; 146 struct i2c_client *client; 147 struct drm_bridge bridge; 148 struct drm_display_mode mode; 149 struct drm_bridge *panel_bridge; 150 struct mipi_dsi_device *dsi; 151 struct gpio_desc *enable_gpio; 152 struct regulator *vdd1; 153 struct regulator *vdd2; 154 struct regulator *vdd3; 155 struct clk *refclk; 156 unsigned long refclk_rate; 157 bool interface_i2c; 158 }; 159 160 static const struct regmap_range chipone_dsi_readable_ranges[] = { 161 regmap_reg_range(VENDOR_ID, VERSION_ID), 162 regmap_reg_range(FIRMWARE_VERSION, PLL_SSC_OFFSET(3)), 163 regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), 164 regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), 165 regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), 166 regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), 167 regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), 168 regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), 169 regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), 170 regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), 171 }; 172 173 static const struct regmap_access_table chipone_dsi_readable_table = { 174 .yes_ranges = chipone_dsi_readable_ranges, 175 .n_yes_ranges = ARRAY_SIZE(chipone_dsi_readable_ranges), 176 }; 177 178 static const struct regmap_range chipone_dsi_writeable_ranges[] = { 179 regmap_reg_range(CONFIG_FINISH, PLL_SSC_OFFSET(3)), 180 regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), 181 regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), 182 regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), 183 regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), 184 regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), 185 regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), 186 regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), 187 regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), 188 }; 189 190 static const struct regmap_access_table chipone_dsi_writeable_table = { 191 .yes_ranges = chipone_dsi_writeable_ranges, 192 .n_yes_ranges = ARRAY_SIZE(chipone_dsi_writeable_ranges), 193 }; 194 195 static const struct regmap_config chipone_regmap_config = { 196 .reg_bits = 8, 197 .val_bits = 8, 198 .rd_table = &chipone_dsi_readable_table, 199 .wr_table = &chipone_dsi_writeable_table, 200 .cache_type = REGCACHE_RBTREE, 201 .max_register = MIPI_ATE_STATUS(1), 202 }; 203 204 static int chipone_dsi_read(void *context, 205 const void *reg, size_t reg_size, 206 void *val, size_t val_size) 207 { 208 struct mipi_dsi_device *dsi = context; 209 const u16 reg16 = (val_size << 8) | *(u8 *)reg; 210 int ret; 211 212 ret = mipi_dsi_generic_read(dsi, ®16, 2, val, val_size); 213 214 return ret == val_size ? 0 : -EINVAL; 215 } 216 217 static int chipone_dsi_write(void *context, const void *data, size_t count) 218 { 219 struct mipi_dsi_device *dsi = context; 220 221 return mipi_dsi_generic_write(dsi, data, 2); 222 } 223 224 static const struct regmap_bus chipone_dsi_regmap_bus = { 225 .read = chipone_dsi_read, 226 .write = chipone_dsi_write, 227 .reg_format_endian_default = REGMAP_ENDIAN_NATIVE, 228 .val_format_endian_default = REGMAP_ENDIAN_NATIVE, 229 }; 230 231 static inline struct chipone *bridge_to_chipone(struct drm_bridge *bridge) 232 { 233 return container_of(bridge, struct chipone, bridge); 234 } 235 236 static void chipone_readb(struct chipone *icn, u8 reg, u8 *val) 237 { 238 int ret, pval; 239 240 ret = regmap_read(icn->regmap, reg, &pval); 241 242 *val = ret ? 0 : pval & 0xff; 243 } 244 245 static int chipone_writeb(struct chipone *icn, u8 reg, u8 val) 246 { 247 return regmap_write(icn->regmap, reg, val); 248 } 249 250 static void chipone_configure_pll(struct chipone *icn, 251 const struct drm_display_mode *mode) 252 { 253 unsigned int best_p = 0, best_m = 0, best_s = 0; 254 unsigned int mode_clock = mode->clock * 1000; 255 unsigned int delta, min_delta = 0xffffffff; 256 unsigned int freq_p, freq_s, freq_out; 257 unsigned int p_min, p_max; 258 unsigned int p, m, s; 259 unsigned int fin; 260 bool best_p_pot; 261 u8 ref_div; 262 263 /* 264 * DSI byte clock frequency (input into PLL) is calculated as: 265 * DSI_CLK = HS clock / 4 266 * 267 * DPI pixel clock frequency (output from PLL) is mode clock. 268 * 269 * The chip contains fractional PLL which works as follows: 270 * DPI_CLK = ((DSI_CLK / P) * M) / S 271 * P is pre-divider, register PLL_REF_DIV[3:0] is 1:n divider 272 * register PLL_REF_DIV[4] is extra 1:2 divider 273 * M is integer multiplier, register PLL_INT(0) is multiplier 274 * S is post-divider, register PLL_REF_DIV[7:5] is 2^(n+1) divider 275 * 276 * It seems the PLL input clock after applying P pre-divider have 277 * to be lower than 20 MHz. 278 */ 279 if (icn->refclk) 280 fin = icn->refclk_rate; 281 else 282 fin = icn->dsi->hs_rate / 4; /* in Hz */ 283 284 /* Minimum value of P predivider for PLL input in 5..20 MHz */ 285 p_min = clamp(DIV_ROUND_UP(fin, 20000000), 1U, 31U); 286 p_max = clamp(fin / 5000000, 1U, 31U); 287 288 for (p = p_min; p < p_max; p++) { /* PLL_REF_DIV[4,3:0] */ 289 if (p > 16 && p & 1) /* P > 16 uses extra /2 */ 290 continue; 291 freq_p = fin / p; 292 if (freq_p == 0) /* Divider too high */ 293 break; 294 295 for (s = 0; s < 0x7; s++) { /* PLL_REF_DIV[7:5] */ 296 freq_s = freq_p / BIT(s + 1); 297 if (freq_s == 0) /* Divider too high */ 298 break; 299 300 m = mode_clock / freq_s; 301 302 /* Multiplier is 8 bit */ 303 if (m > 0xff) 304 continue; 305 306 /* Limit PLL VCO frequency to 1 GHz */ 307 freq_out = (fin * m) / p; 308 if (freq_out > 1000000000) 309 continue; 310 311 /* Apply post-divider */ 312 freq_out /= BIT(s + 1); 313 314 delta = abs(mode_clock - freq_out); 315 if (delta < min_delta) { 316 best_p = p; 317 best_m = m; 318 best_s = s; 319 min_delta = delta; 320 } 321 } 322 } 323 324 best_p_pot = !(best_p & 1); 325 326 dev_dbg(icn->dev, 327 "PLL: P[3:0]=%d P[4]=2*%d M=%d S[7:5]=2^%d delta=%d => DSI f_in(%s)=%d Hz ; DPI f_out=%d Hz\n", 328 best_p >> best_p_pot, best_p_pot, best_m, best_s + 1, 329 min_delta, icn->refclk ? "EXT" : "DSI", fin, 330 (fin * best_m) / (best_p << (best_s + 1))); 331 332 ref_div = PLL_REF_DIV_P(best_p >> best_p_pot) | PLL_REF_DIV_S(best_s); 333 if (best_p_pot) /* Prefer /2 pre-divider */ 334 ref_div |= PLL_REF_DIV_Pe; 335 336 /* Clock source selection either external clock or MIPI DSI clock lane */ 337 chipone_writeb(icn, PLL_CTRL(6), 338 icn->refclk ? PLL_CTRL_6_EXTERNAL : PLL_CTRL_6_MIPI_CLK); 339 chipone_writeb(icn, PLL_REF_DIV, ref_div); 340 chipone_writeb(icn, PLL_INT(0), best_m); 341 } 342 343 static void chipone_atomic_enable(struct drm_bridge *bridge, 344 struct drm_bridge_state *old_bridge_state) 345 { 346 struct chipone *icn = bridge_to_chipone(bridge); 347 struct drm_atomic_state *state = old_bridge_state->base.state; 348 struct drm_display_mode *mode = &icn->mode; 349 const struct drm_bridge_state *bridge_state; 350 u16 hfp, hbp, hsync; 351 u32 bus_flags; 352 u8 pol, sys_ctrl_1, id[4]; 353 354 chipone_readb(icn, VENDOR_ID, id); 355 chipone_readb(icn, DEVICE_ID_H, id + 1); 356 chipone_readb(icn, DEVICE_ID_L, id + 2); 357 chipone_readb(icn, VERSION_ID, id + 3); 358 359 dev_dbg(icn->dev, 360 "Chip IDs: Vendor=0x%02x Device=0x%02x:0x%02x Version=0x%02x\n", 361 id[0], id[1], id[2], id[3]); 362 363 if (id[0] != 0xc1 || id[1] != 0x62 || id[2] != 0x11) { 364 dev_dbg(icn->dev, "Invalid Chip IDs, aborting configuration\n"); 365 return; 366 } 367 368 /* Get the DPI flags from the bridge state. */ 369 bridge_state = drm_atomic_get_new_bridge_state(state, bridge); 370 bus_flags = bridge_state->output_bus_cfg.flags; 371 372 if (icn->interface_i2c) 373 chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_I2C); 374 else 375 chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI); 376 377 chipone_writeb(icn, HACTIVE_LI, mode->hdisplay & 0xff); 378 379 chipone_writeb(icn, VACTIVE_LI, mode->vdisplay & 0xff); 380 381 /* 382 * lsb nibble: 2nd nibble of hdisplay 383 * msb nibble: 2nd nibble of vdisplay 384 */ 385 chipone_writeb(icn, VACTIVE_HACTIVE_HI, 386 ((mode->hdisplay >> 8) & 0xf) | 387 (((mode->vdisplay >> 8) & 0xf) << 4)); 388 389 hfp = mode->hsync_start - mode->hdisplay; 390 hsync = mode->hsync_end - mode->hsync_start; 391 hbp = mode->htotal - mode->hsync_end; 392 393 chipone_writeb(icn, HFP_LI, hfp & 0xff); 394 chipone_writeb(icn, HSYNC_LI, hsync & 0xff); 395 chipone_writeb(icn, HBP_LI, hbp & 0xff); 396 /* Top two bits of Horizontal Front porch/Sync/Back porch */ 397 chipone_writeb(icn, HFP_HSW_HBP_HI, 398 HFP_HSW_HBP_HI_HFP(hfp) | 399 HFP_HSW_HBP_HI_HS(hsync) | 400 HFP_HSW_HBP_HI_HBP(hbp)); 401 402 chipone_writeb(icn, VFP, mode->vsync_start - mode->vdisplay); 403 404 chipone_writeb(icn, VSYNC, mode->vsync_end - mode->vsync_start); 405 406 chipone_writeb(icn, VBP, mode->vtotal - mode->vsync_end); 407 408 /* dsi specific sequence */ 409 chipone_writeb(icn, SYNC_EVENT_DLY, 0x80); 410 chipone_writeb(icn, HFP_MIN, hfp & 0xff); 411 412 /* DSI data lane count */ 413 chipone_writeb(icn, DSI_CTRL, 414 DSI_CTRL_UNKNOWN | DSI_CTRL_DSI_LANES(icn->dsi->lanes - 1)); 415 416 chipone_writeb(icn, MIPI_PD_CK_LANE, 0xa0); 417 chipone_writeb(icn, PLL_CTRL(12), 0xff); 418 chipone_writeb(icn, MIPI_PN_SWAP, 0x00); 419 420 /* DPI HS/VS/DE polarity */ 421 pol = ((mode->flags & DRM_MODE_FLAG_PHSYNC) ? BIST_POL_HSYNC_POL : 0) | 422 ((mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIST_POL_VSYNC_POL : 0) | 423 ((bus_flags & DRM_BUS_FLAG_DE_HIGH) ? BIST_POL_DE_POL : 0); 424 chipone_writeb(icn, BIST_POL, pol); 425 426 /* Configure PLL settings */ 427 chipone_configure_pll(icn, mode); 428 429 chipone_writeb(icn, SYS_CTRL(0), 0x40); 430 sys_ctrl_1 = 0x88; 431 432 if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) 433 sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_0); 434 else 435 sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_1_2); 436 437 chipone_writeb(icn, SYS_CTRL(1), sys_ctrl_1); 438 439 /* icn6211 specific sequence */ 440 chipone_writeb(icn, MIPI_FORCE_0, 0x20); 441 chipone_writeb(icn, PLL_CTRL(1), 0x20); 442 chipone_writeb(icn, CONFIG_FINISH, 0x10); 443 444 usleep_range(10000, 11000); 445 } 446 447 static void chipone_atomic_pre_enable(struct drm_bridge *bridge, 448 struct drm_bridge_state *old_bridge_state) 449 { 450 struct chipone *icn = bridge_to_chipone(bridge); 451 int ret; 452 453 if (icn->vdd1) { 454 ret = regulator_enable(icn->vdd1); 455 if (ret) 456 DRM_DEV_ERROR(icn->dev, 457 "failed to enable VDD1 regulator: %d\n", ret); 458 } 459 460 if (icn->vdd2) { 461 ret = regulator_enable(icn->vdd2); 462 if (ret) 463 DRM_DEV_ERROR(icn->dev, 464 "failed to enable VDD2 regulator: %d\n", ret); 465 } 466 467 if (icn->vdd3) { 468 ret = regulator_enable(icn->vdd3); 469 if (ret) 470 DRM_DEV_ERROR(icn->dev, 471 "failed to enable VDD3 regulator: %d\n", ret); 472 } 473 474 ret = clk_prepare_enable(icn->refclk); 475 if (ret) 476 DRM_DEV_ERROR(icn->dev, 477 "failed to enable RECLK clock: %d\n", ret); 478 479 gpiod_set_value(icn->enable_gpio, 1); 480 481 usleep_range(10000, 11000); 482 } 483 484 static void chipone_atomic_post_disable(struct drm_bridge *bridge, 485 struct drm_bridge_state *old_bridge_state) 486 { 487 struct chipone *icn = bridge_to_chipone(bridge); 488 489 clk_disable_unprepare(icn->refclk); 490 491 if (icn->vdd1) 492 regulator_disable(icn->vdd1); 493 494 if (icn->vdd2) 495 regulator_disable(icn->vdd2); 496 497 if (icn->vdd3) 498 regulator_disable(icn->vdd3); 499 500 gpiod_set_value(icn->enable_gpio, 0); 501 } 502 503 static void chipone_mode_set(struct drm_bridge *bridge, 504 const struct drm_display_mode *mode, 505 const struct drm_display_mode *adjusted_mode) 506 { 507 struct chipone *icn = bridge_to_chipone(bridge); 508 509 drm_mode_copy(&icn->mode, adjusted_mode); 510 }; 511 512 static int chipone_dsi_attach(struct chipone *icn) 513 { 514 struct mipi_dsi_device *dsi = icn->dsi; 515 struct device *dev = icn->dev; 516 int dsi_lanes, ret; 517 518 dsi_lanes = drm_of_get_data_lanes_count_ep(dev->of_node, 0, 0, 1, 4); 519 520 /* 521 * If the 'data-lanes' property does not exist in DT or is invalid, 522 * default to previously hard-coded behavior, which was 4 data lanes. 523 */ 524 if (dsi_lanes < 0) 525 icn->dsi->lanes = 4; 526 else 527 icn->dsi->lanes = dsi_lanes; 528 529 dsi->format = MIPI_DSI_FMT_RGB888; 530 dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | 531 MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET; 532 dsi->hs_rate = 500000000; 533 dsi->lp_rate = 16000000; 534 535 ret = mipi_dsi_attach(dsi); 536 if (ret < 0) 537 dev_err(icn->dev, "failed to attach dsi\n"); 538 539 return ret; 540 } 541 542 static int chipone_dsi_host_attach(struct chipone *icn) 543 { 544 struct device *dev = icn->dev; 545 struct device_node *host_node; 546 struct device_node *endpoint; 547 struct mipi_dsi_device *dsi; 548 struct mipi_dsi_host *host; 549 int ret = 0; 550 551 const struct mipi_dsi_device_info info = { 552 .type = "chipone", 553 .channel = 0, 554 .node = NULL, 555 }; 556 557 endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0); 558 host_node = of_graph_get_remote_port_parent(endpoint); 559 of_node_put(endpoint); 560 561 if (!host_node) 562 return -EINVAL; 563 564 host = of_find_mipi_dsi_host_by_node(host_node); 565 of_node_put(host_node); 566 if (!host) { 567 dev_err(dev, "failed to find dsi host\n"); 568 return -EPROBE_DEFER; 569 } 570 571 dsi = mipi_dsi_device_register_full(host, &info); 572 if (IS_ERR(dsi)) { 573 return dev_err_probe(dev, PTR_ERR(dsi), 574 "failed to create dsi device\n"); 575 } 576 577 icn->dsi = dsi; 578 579 ret = chipone_dsi_attach(icn); 580 if (ret < 0) 581 mipi_dsi_device_unregister(dsi); 582 583 return ret; 584 } 585 586 static int chipone_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags) 587 { 588 struct chipone *icn = bridge_to_chipone(bridge); 589 590 return drm_bridge_attach(bridge->encoder, icn->panel_bridge, bridge, flags); 591 } 592 593 #define MAX_INPUT_SEL_FORMATS 1 594 595 static u32 * 596 chipone_atomic_get_input_bus_fmts(struct drm_bridge *bridge, 597 struct drm_bridge_state *bridge_state, 598 struct drm_crtc_state *crtc_state, 599 struct drm_connector_state *conn_state, 600 u32 output_fmt, 601 unsigned int *num_input_fmts) 602 { 603 u32 *input_fmts; 604 605 *num_input_fmts = 0; 606 607 input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), 608 GFP_KERNEL); 609 if (!input_fmts) 610 return NULL; 611 612 /* This is the DSI-end bus format */ 613 input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; 614 *num_input_fmts = 1; 615 616 return input_fmts; 617 } 618 619 static const struct drm_bridge_funcs chipone_bridge_funcs = { 620 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 621 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 622 .atomic_reset = drm_atomic_helper_bridge_reset, 623 .atomic_pre_enable = chipone_atomic_pre_enable, 624 .atomic_enable = chipone_atomic_enable, 625 .atomic_post_disable = chipone_atomic_post_disable, 626 .mode_set = chipone_mode_set, 627 .attach = chipone_attach, 628 .atomic_get_input_bus_fmts = chipone_atomic_get_input_bus_fmts, 629 }; 630 631 static int chipone_parse_dt(struct chipone *icn) 632 { 633 struct device *dev = icn->dev; 634 int ret; 635 636 icn->refclk = devm_clk_get_optional(dev, "refclk"); 637 if (IS_ERR(icn->refclk)) { 638 ret = PTR_ERR(icn->refclk); 639 DRM_DEV_ERROR(dev, "failed to get REFCLK clock: %d\n", ret); 640 return ret; 641 } else if (icn->refclk) { 642 icn->refclk_rate = clk_get_rate(icn->refclk); 643 if (icn->refclk_rate < 10000000 || icn->refclk_rate > 154000000) { 644 DRM_DEV_ERROR(dev, "REFCLK out of range: %ld Hz\n", 645 icn->refclk_rate); 646 return -EINVAL; 647 } 648 } 649 650 icn->vdd1 = devm_regulator_get_optional(dev, "vdd1"); 651 if (IS_ERR(icn->vdd1)) { 652 ret = PTR_ERR(icn->vdd1); 653 if (ret == -EPROBE_DEFER) 654 return -EPROBE_DEFER; 655 icn->vdd1 = NULL; 656 DRM_DEV_DEBUG(dev, "failed to get VDD1 regulator: %d\n", ret); 657 } 658 659 icn->vdd2 = devm_regulator_get_optional(dev, "vdd2"); 660 if (IS_ERR(icn->vdd2)) { 661 ret = PTR_ERR(icn->vdd2); 662 if (ret == -EPROBE_DEFER) 663 return -EPROBE_DEFER; 664 icn->vdd2 = NULL; 665 DRM_DEV_DEBUG(dev, "failed to get VDD2 regulator: %d\n", ret); 666 } 667 668 icn->vdd3 = devm_regulator_get_optional(dev, "vdd3"); 669 if (IS_ERR(icn->vdd3)) { 670 ret = PTR_ERR(icn->vdd3); 671 if (ret == -EPROBE_DEFER) 672 return -EPROBE_DEFER; 673 icn->vdd3 = NULL; 674 DRM_DEV_DEBUG(dev, "failed to get VDD3 regulator: %d\n", ret); 675 } 676 677 icn->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); 678 if (IS_ERR(icn->enable_gpio)) { 679 DRM_DEV_ERROR(dev, "failed to get enable GPIO\n"); 680 return PTR_ERR(icn->enable_gpio); 681 } 682 683 icn->panel_bridge = devm_drm_of_get_bridge(dev, dev->of_node, 1, 0); 684 if (IS_ERR(icn->panel_bridge)) 685 return PTR_ERR(icn->panel_bridge); 686 687 return 0; 688 } 689 690 static int chipone_common_probe(struct device *dev, struct chipone **icnr) 691 { 692 struct chipone *icn; 693 int ret; 694 695 icn = devm_kzalloc(dev, sizeof(struct chipone), GFP_KERNEL); 696 if (!icn) 697 return -ENOMEM; 698 699 icn->dev = dev; 700 701 ret = chipone_parse_dt(icn); 702 if (ret) 703 return ret; 704 705 icn->bridge.funcs = &chipone_bridge_funcs; 706 icn->bridge.type = DRM_MODE_CONNECTOR_DPI; 707 icn->bridge.of_node = dev->of_node; 708 709 *icnr = icn; 710 711 return ret; 712 } 713 714 static int chipone_dsi_probe(struct mipi_dsi_device *dsi) 715 { 716 struct device *dev = &dsi->dev; 717 struct chipone *icn; 718 int ret; 719 720 ret = chipone_common_probe(dev, &icn); 721 if (ret) 722 return ret; 723 724 icn->regmap = devm_regmap_init(dev, &chipone_dsi_regmap_bus, 725 dsi, &chipone_regmap_config); 726 if (IS_ERR(icn->regmap)) 727 return PTR_ERR(icn->regmap); 728 729 icn->interface_i2c = false; 730 icn->dsi = dsi; 731 732 mipi_dsi_set_drvdata(dsi, icn); 733 734 drm_bridge_add(&icn->bridge); 735 736 ret = chipone_dsi_attach(icn); 737 if (ret) 738 drm_bridge_remove(&icn->bridge); 739 740 return ret; 741 } 742 743 static int chipone_i2c_probe(struct i2c_client *client) 744 { 745 struct device *dev = &client->dev; 746 struct chipone *icn; 747 int ret; 748 749 ret = chipone_common_probe(dev, &icn); 750 if (ret) 751 return ret; 752 753 icn->regmap = devm_regmap_init_i2c(client, &chipone_regmap_config); 754 if (IS_ERR(icn->regmap)) 755 return PTR_ERR(icn->regmap); 756 757 icn->interface_i2c = true; 758 icn->client = client; 759 dev_set_drvdata(dev, icn); 760 i2c_set_clientdata(client, icn); 761 762 drm_bridge_add(&icn->bridge); 763 764 return chipone_dsi_host_attach(icn); 765 } 766 767 static void chipone_dsi_remove(struct mipi_dsi_device *dsi) 768 { 769 struct chipone *icn = mipi_dsi_get_drvdata(dsi); 770 771 mipi_dsi_detach(dsi); 772 drm_bridge_remove(&icn->bridge); 773 } 774 775 static const struct of_device_id chipone_of_match[] = { 776 { .compatible = "chipone,icn6211", }, 777 { /* sentinel */ } 778 }; 779 MODULE_DEVICE_TABLE(of, chipone_of_match); 780 781 static struct mipi_dsi_driver chipone_dsi_driver = { 782 .probe = chipone_dsi_probe, 783 .remove = chipone_dsi_remove, 784 .driver = { 785 .name = "chipone-icn6211", 786 .owner = THIS_MODULE, 787 .of_match_table = chipone_of_match, 788 }, 789 }; 790 791 static struct i2c_device_id chipone_i2c_id[] = { 792 { "chipone,icn6211" }, 793 {}, 794 }; 795 MODULE_DEVICE_TABLE(i2c, chipone_i2c_id); 796 797 static struct i2c_driver chipone_i2c_driver = { 798 .probe_new = chipone_i2c_probe, 799 .id_table = chipone_i2c_id, 800 .driver = { 801 .name = "chipone-icn6211-i2c", 802 .of_match_table = chipone_of_match, 803 }, 804 }; 805 806 static int __init chipone_init(void) 807 { 808 if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) 809 mipi_dsi_driver_register(&chipone_dsi_driver); 810 811 return i2c_add_driver(&chipone_i2c_driver); 812 } 813 module_init(chipone_init); 814 815 static void __exit chipone_exit(void) 816 { 817 i2c_del_driver(&chipone_i2c_driver); 818 819 if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) 820 mipi_dsi_driver_unregister(&chipone_dsi_driver); 821 } 822 module_exit(chipone_exit); 823 824 MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); 825 MODULE_DESCRIPTION("Chipone ICN6211 MIPI-DSI to RGB Converter Bridge"); 826 MODULE_LICENSE("GPL"); 827