1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright(c) 2020, Analogix Semiconductor. All rights reserved. 4 * 5 */ 6 #include <linux/gcd.h> 7 #include <linux/gpio/consumer.h> 8 #include <linux/i2c.h> 9 #include <linux/interrupt.h> 10 #include <linux/iopoll.h> 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/mutex.h> 14 #include <linux/pm_runtime.h> 15 #include <linux/regulator/consumer.h> 16 #include <linux/slab.h> 17 #include <linux/types.h> 18 #include <linux/workqueue.h> 19 20 #include <linux/of_gpio.h> 21 #include <linux/of_graph.h> 22 #include <linux/of_platform.h> 23 24 #include <drm/display/drm_dp_aux_bus.h> 25 #include <drm/display/drm_dp_helper.h> 26 #include <drm/display/drm_hdcp_helper.h> 27 #include <drm/drm_atomic_helper.h> 28 #include <drm/drm_bridge.h> 29 #include <drm/drm_crtc_helper.h> 30 #include <drm/drm_edid.h> 31 #include <drm/drm_mipi_dsi.h> 32 #include <drm/drm_of.h> 33 #include <drm/drm_panel.h> 34 #include <drm/drm_print.h> 35 #include <drm/drm_probe_helper.h> 36 37 #include <media/v4l2-fwnode.h> 38 #include <sound/hdmi-codec.h> 39 #include <video/display_timing.h> 40 41 #include "anx7625.h" 42 43 /* 44 * There is a sync issue while access I2C register between AP(CPU) and 45 * internal firmware(OCM), to avoid the race condition, AP should access 46 * the reserved slave address before slave address occurs changes. 47 */ 48 static int i2c_access_workaround(struct anx7625_data *ctx, 49 struct i2c_client *client) 50 { 51 u8 offset; 52 struct device *dev = &client->dev; 53 int ret; 54 55 if (client == ctx->last_client) 56 return 0; 57 58 ctx->last_client = client; 59 60 if (client == ctx->i2c.tcpc_client) 61 offset = RSVD_00_ADDR; 62 else if (client == ctx->i2c.tx_p0_client) 63 offset = RSVD_D1_ADDR; 64 else if (client == ctx->i2c.tx_p1_client) 65 offset = RSVD_60_ADDR; 66 else if (client == ctx->i2c.rx_p0_client) 67 offset = RSVD_39_ADDR; 68 else if (client == ctx->i2c.rx_p1_client) 69 offset = RSVD_7F_ADDR; 70 else 71 offset = RSVD_00_ADDR; 72 73 ret = i2c_smbus_write_byte_data(client, offset, 0x00); 74 if (ret < 0) 75 DRM_DEV_ERROR(dev, 76 "fail to access i2c id=%x\n:%x", 77 client->addr, offset); 78 79 return ret; 80 } 81 82 static int anx7625_reg_read(struct anx7625_data *ctx, 83 struct i2c_client *client, u8 reg_addr) 84 { 85 int ret; 86 struct device *dev = &client->dev; 87 88 i2c_access_workaround(ctx, client); 89 90 ret = i2c_smbus_read_byte_data(client, reg_addr); 91 if (ret < 0) 92 DRM_DEV_ERROR(dev, "read i2c fail id=%x:%x\n", 93 client->addr, reg_addr); 94 95 return ret; 96 } 97 98 static int anx7625_reg_block_read(struct anx7625_data *ctx, 99 struct i2c_client *client, 100 u8 reg_addr, u8 len, u8 *buf) 101 { 102 int ret; 103 struct device *dev = &client->dev; 104 105 i2c_access_workaround(ctx, client); 106 107 ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf); 108 if (ret < 0) 109 DRM_DEV_ERROR(dev, "read i2c block fail id=%x:%x\n", 110 client->addr, reg_addr); 111 112 return ret; 113 } 114 115 static int anx7625_reg_write(struct anx7625_data *ctx, 116 struct i2c_client *client, 117 u8 reg_addr, u8 reg_val) 118 { 119 int ret; 120 struct device *dev = &client->dev; 121 122 i2c_access_workaround(ctx, client); 123 124 ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val); 125 126 if (ret < 0) 127 DRM_DEV_ERROR(dev, "fail to write i2c id=%x\n:%x", 128 client->addr, reg_addr); 129 130 return ret; 131 } 132 133 static int anx7625_reg_block_write(struct anx7625_data *ctx, 134 struct i2c_client *client, 135 u8 reg_addr, u8 len, u8 *buf) 136 { 137 int ret; 138 struct device *dev = &client->dev; 139 140 i2c_access_workaround(ctx, client); 141 142 ret = i2c_smbus_write_i2c_block_data(client, reg_addr, len, buf); 143 if (ret < 0) 144 dev_err(dev, "write i2c block failed id=%x\n:%x", 145 client->addr, reg_addr); 146 147 return ret; 148 } 149 150 static int anx7625_write_or(struct anx7625_data *ctx, 151 struct i2c_client *client, 152 u8 offset, u8 mask) 153 { 154 int val; 155 156 val = anx7625_reg_read(ctx, client, offset); 157 if (val < 0) 158 return val; 159 160 return anx7625_reg_write(ctx, client, offset, (val | (mask))); 161 } 162 163 static int anx7625_write_and(struct anx7625_data *ctx, 164 struct i2c_client *client, 165 u8 offset, u8 mask) 166 { 167 int val; 168 169 val = anx7625_reg_read(ctx, client, offset); 170 if (val < 0) 171 return val; 172 173 return anx7625_reg_write(ctx, client, offset, (val & (mask))); 174 } 175 176 static int anx7625_write_and_or(struct anx7625_data *ctx, 177 struct i2c_client *client, 178 u8 offset, u8 and_mask, u8 or_mask) 179 { 180 int val; 181 182 val = anx7625_reg_read(ctx, client, offset); 183 if (val < 0) 184 return val; 185 186 return anx7625_reg_write(ctx, client, 187 offset, (val & and_mask) | (or_mask)); 188 } 189 190 static int anx7625_config_bit_matrix(struct anx7625_data *ctx) 191 { 192 int i, ret; 193 194 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 195 AUDIO_CONTROL_REGISTER, 0x80); 196 for (i = 0; i < 13; i++) 197 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 198 VIDEO_BIT_MATRIX_12 + i, 199 0x18 + i); 200 201 return ret; 202 } 203 204 static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) 205 { 206 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS); 207 } 208 209 static int wait_aux_op_finish(struct anx7625_data *ctx) 210 { 211 struct device *dev = &ctx->client->dev; 212 int val; 213 int ret; 214 215 ret = readx_poll_timeout(anx7625_read_ctrl_status_p0, 216 ctx, val, 217 (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)), 218 2000, 219 2000 * 150); 220 if (ret) { 221 DRM_DEV_ERROR(dev, "aux operation fail!\n"); 222 return -EIO; 223 } 224 225 val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 226 AP_AUX_CTRL_STATUS); 227 if (val < 0 || (val & 0x0F)) { 228 DRM_DEV_ERROR(dev, "aux status %02x\n", val); 229 return -EIO; 230 } 231 232 return 0; 233 } 234 235 static int anx7625_aux_trans(struct anx7625_data *ctx, u8 op, u32 address, 236 u8 len, u8 *buf) 237 { 238 struct device *dev = &ctx->client->dev; 239 int ret; 240 u8 addrh, addrm, addrl; 241 u8 cmd; 242 bool is_write = !(op & DP_AUX_I2C_READ); 243 244 if (len > DP_AUX_MAX_PAYLOAD_BYTES) { 245 dev_err(dev, "exceed aux buffer len.\n"); 246 return -EINVAL; 247 } 248 249 if (!len) 250 return len; 251 252 addrl = address & 0xFF; 253 addrm = (address >> 8) & 0xFF; 254 addrh = (address >> 16) & 0xFF; 255 256 if (!is_write) 257 op &= ~DP_AUX_I2C_MOT; 258 cmd = DPCD_CMD(len, op); 259 260 /* Set command and length */ 261 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 262 AP_AUX_COMMAND, cmd); 263 264 /* Set aux access address */ 265 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 266 AP_AUX_ADDR_7_0, addrl); 267 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 268 AP_AUX_ADDR_15_8, addrm); 269 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 270 AP_AUX_ADDR_19_16, addrh); 271 272 if (is_write) 273 ret |= anx7625_reg_block_write(ctx, ctx->i2c.rx_p0_client, 274 AP_AUX_BUFF_START, len, buf); 275 /* Enable aux access */ 276 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 277 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 278 279 if (ret < 0) { 280 dev_err(dev, "cannot access aux related register.\n"); 281 return -EIO; 282 } 283 284 ret = wait_aux_op_finish(ctx); 285 if (ret < 0) { 286 dev_err(dev, "aux IO error: wait aux op finish.\n"); 287 return ret; 288 } 289 290 /* Write done */ 291 if (is_write) 292 return len; 293 294 /* Read done, read out dpcd data */ 295 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 296 AP_AUX_BUFF_START, len, buf); 297 if (ret < 0) { 298 dev_err(dev, "read dpcd register failed\n"); 299 return -EIO; 300 } 301 302 return len; 303 } 304 305 static int anx7625_video_mute_control(struct anx7625_data *ctx, 306 u8 status) 307 { 308 int ret; 309 310 if (status) { 311 /* Set mute on flag */ 312 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 313 AP_AV_STATUS, AP_MIPI_MUTE); 314 /* Clear mipi RX en */ 315 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 316 AP_AV_STATUS, (u8)~AP_MIPI_RX_EN); 317 } else { 318 /* Mute off flag */ 319 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 320 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 321 /* Set MIPI RX EN */ 322 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 323 AP_AV_STATUS, AP_MIPI_RX_EN); 324 } 325 326 return ret; 327 } 328 329 /* Reduction of fraction a/b */ 330 static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) 331 { 332 unsigned long gcd_num; 333 unsigned long tmp_a, tmp_b; 334 u32 i = 1; 335 336 gcd_num = gcd(*a, *b); 337 *a /= gcd_num; 338 *b /= gcd_num; 339 340 tmp_a = *a; 341 tmp_b = *b; 342 343 while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) { 344 i++; 345 *a = tmp_a / i; 346 *b = tmp_b / i; 347 } 348 349 /* 350 * In the end, make a, b larger to have higher ODFC PLL 351 * output frequency accuracy 352 */ 353 while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) { 354 *a <<= 1; 355 *b <<= 1; 356 } 357 358 *a >>= 1; 359 *b >>= 1; 360 } 361 362 static int anx7625_calculate_m_n(u32 pixelclock, 363 unsigned long *m, 364 unsigned long *n, 365 u8 *post_divider) 366 { 367 if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) { 368 /* Pixel clock frequency is too high */ 369 DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n", 370 pixelclock, 371 PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN); 372 return -EINVAL; 373 } 374 375 if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) { 376 /* Pixel clock frequency is too low */ 377 DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n", 378 pixelclock, 379 PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX); 380 return -EINVAL; 381 } 382 383 for (*post_divider = 1; 384 pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));) 385 *post_divider += 1; 386 387 if (*post_divider > POST_DIVIDER_MAX) { 388 for (*post_divider = 1; 389 (pixelclock < 390 (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));) 391 *post_divider += 1; 392 393 if (*post_divider > POST_DIVIDER_MAX) { 394 DRM_ERROR("cannot find property post_divider(%d)\n", 395 *post_divider); 396 return -EDOM; 397 } 398 } 399 400 /* Patch to improve the accuracy */ 401 if (*post_divider == 7) { 402 /* 27,000,000 is not divisible by 7 */ 403 *post_divider = 8; 404 } else if (*post_divider == 11) { 405 /* 27,000,000 is not divisible by 11 */ 406 *post_divider = 12; 407 } else if ((*post_divider == 13) || (*post_divider == 14)) { 408 /* 27,000,000 is not divisible by 13 or 14 */ 409 *post_divider = 15; 410 } 411 412 if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) { 413 DRM_ERROR("act clock(%u) large than maximum(%lu)\n", 414 pixelclock * (*post_divider), 415 PLL_OUT_FREQ_ABS_MAX); 416 return -EDOM; 417 } 418 419 *m = pixelclock; 420 *n = XTAL_FRQ / (*post_divider); 421 422 anx7625_reduction_of_a_fraction(m, n); 423 424 return 0; 425 } 426 427 static int anx7625_odfc_config(struct anx7625_data *ctx, 428 u8 post_divider) 429 { 430 int ret; 431 struct device *dev = &ctx->client->dev; 432 433 /* Config input reference clock frequency 27MHz/19.2MHz */ 434 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 435 ~(REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 436 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 437 (REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 438 /* Post divider */ 439 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 440 MIPI_DIGITAL_PLL_8, 0x0f); 441 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8, 442 post_divider << 4); 443 444 /* Add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */ 445 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 446 ~MIPI_PLL_VCO_TUNE_REG_VAL); 447 448 /* Reset ODFC PLL */ 449 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 450 ~MIPI_PLL_RESET_N); 451 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 452 MIPI_PLL_RESET_N); 453 454 if (ret < 0) 455 DRM_DEV_ERROR(dev, "IO error.\n"); 456 457 return ret; 458 } 459 460 /* 461 * The MIPI source video data exist large variation (e.g. 59Hz ~ 61Hz), 462 * anx7625 defined K ratio for matching MIPI input video clock and 463 * DP output video clock. Increase K value can match bigger video data 464 * variation. IVO panel has small variation than DP CTS spec, need 465 * decrease the K value. 466 */ 467 static int anx7625_set_k_value(struct anx7625_data *ctx) 468 { 469 struct edid *edid = (struct edid *)ctx->slimport_edid_p.edid_raw_data; 470 471 if (edid->mfg_id[0] == IVO_MID0 && edid->mfg_id[1] == IVO_MID1) 472 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 473 MIPI_DIGITAL_ADJ_1, 0x3B); 474 475 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 476 MIPI_DIGITAL_ADJ_1, 0x3D); 477 } 478 479 static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) 480 { 481 struct device *dev = &ctx->client->dev; 482 unsigned long m, n; 483 u16 htotal; 484 int ret; 485 u8 post_divider = 0; 486 487 ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000, 488 &m, &n, &post_divider); 489 490 if (ret) { 491 DRM_DEV_ERROR(dev, "cannot get property m n value.\n"); 492 return ret; 493 } 494 495 DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n", 496 m, n, post_divider); 497 498 /* Configure pixel clock */ 499 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L, 500 (ctx->dt.pixelclock.min / 1000) & 0xFF); 501 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H, 502 (ctx->dt.pixelclock.min / 1000) >> 8); 503 /* Lane count */ 504 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 505 MIPI_LANE_CTRL_0, 0xfc); 506 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 507 MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); 508 509 /* Htotal */ 510 htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + 511 ctx->dt.hback_porch.min + ctx->dt.hsync_len.min; 512 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 513 HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF); 514 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 515 HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8); 516 /* Hactive */ 517 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 518 HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF); 519 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 520 HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8); 521 /* HFP */ 522 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 523 HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min); 524 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 525 HORIZONTAL_FRONT_PORCH_H, 526 ctx->dt.hfront_porch.min >> 8); 527 /* HWS */ 528 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 529 HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min); 530 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 531 HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8); 532 /* HBP */ 533 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 534 HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min); 535 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 536 HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8); 537 /* Vactive */ 538 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L, 539 ctx->dt.vactive.min); 540 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H, 541 ctx->dt.vactive.min >> 8); 542 /* VFP */ 543 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 544 VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min); 545 /* VWS */ 546 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 547 VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min); 548 /* VBP */ 549 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 550 VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min); 551 /* M value */ 552 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 553 MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff); 554 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 555 MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff); 556 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 557 MIPI_PLL_M_NUM_7_0, (m & 0xff)); 558 /* N value */ 559 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 560 MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff); 561 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 562 MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff); 563 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0, 564 (n & 0xff)); 565 566 anx7625_set_k_value(ctx); 567 568 ret |= anx7625_odfc_config(ctx, post_divider - 1); 569 570 if (ret < 0) 571 DRM_DEV_ERROR(dev, "mipi dsi setup IO error.\n"); 572 573 return ret; 574 } 575 576 static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx) 577 { 578 int val; 579 struct device *dev = &ctx->client->dev; 580 581 /* Swap MIPI-DSI data lane 3 P and N */ 582 val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP); 583 if (val < 0) { 584 DRM_DEV_ERROR(dev, "IO error : access MIPI_SWAP.\n"); 585 return -EIO; 586 } 587 588 val |= (1 << MIPI_SWAP_CH3); 589 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val); 590 } 591 592 static int anx7625_api_dsi_config(struct anx7625_data *ctx) 593 594 { 595 int val, ret; 596 struct device *dev = &ctx->client->dev; 597 598 /* Swap MIPI-DSI data lane 3 P and N */ 599 ret = anx7625_swap_dsi_lane3(ctx); 600 if (ret < 0) { 601 DRM_DEV_ERROR(dev, "IO error : swap dsi lane 3 fail.\n"); 602 return ret; 603 } 604 605 /* DSI clock settings */ 606 val = (0 << MIPI_HS_PWD_CLK) | 607 (0 << MIPI_HS_RT_CLK) | 608 (0 << MIPI_PD_CLK) | 609 (1 << MIPI_CLK_RT_MANUAL_PD_EN) | 610 (1 << MIPI_CLK_HS_MANUAL_PD_EN) | 611 (0 << MIPI_CLK_DET_DET_BYPASS) | 612 (0 << MIPI_CLK_MISS_CTRL) | 613 (0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN); 614 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 615 MIPI_PHY_CONTROL_3, val); 616 617 /* 618 * Decreased HS prepare timing delay from 160ns to 80ns work with 619 * a) Dragon board 810 series (Qualcomm AP) 620 * b) Moving Pixel DSI source (PG3A pattern generator + 621 * P332 D-PHY Probe) default D-PHY timing 622 * 5ns/step 623 */ 624 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 625 MIPI_TIME_HS_PRPR, 0x10); 626 627 /* Enable DSI mode*/ 628 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18, 629 SELECT_DSI << MIPI_DPI_SELECT); 630 631 ret |= anx7625_dsi_video_timing_config(ctx); 632 if (ret < 0) { 633 DRM_DEV_ERROR(dev, "dsi video timing config fail\n"); 634 return ret; 635 } 636 637 /* Toggle m, n ready */ 638 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 639 ~(MIPI_M_NUM_READY | MIPI_N_NUM_READY)); 640 usleep_range(1000, 1100); 641 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 642 MIPI_M_NUM_READY | MIPI_N_NUM_READY); 643 644 /* Configure integer stable register */ 645 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 646 MIPI_VIDEO_STABLE_CNT, 0x02); 647 /* Power on MIPI RX */ 648 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 649 MIPI_LANE_CTRL_10, 0x00); 650 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 651 MIPI_LANE_CTRL_10, 0x80); 652 653 if (ret < 0) 654 DRM_DEV_ERROR(dev, "IO error : mipi dsi enable init fail.\n"); 655 656 return ret; 657 } 658 659 static int anx7625_dsi_config(struct anx7625_data *ctx) 660 { 661 struct device *dev = &ctx->client->dev; 662 int ret; 663 664 DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n"); 665 666 /* DSC disable */ 667 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 668 R_DSC_CTRL_0, ~DSC_EN); 669 670 ret |= anx7625_api_dsi_config(ctx); 671 672 if (ret < 0) { 673 DRM_DEV_ERROR(dev, "IO error : api dsi config error.\n"); 674 return ret; 675 } 676 677 /* Set MIPI RX EN */ 678 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 679 AP_AV_STATUS, AP_MIPI_RX_EN); 680 /* Clear mute flag */ 681 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 682 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 683 if (ret < 0) 684 DRM_DEV_ERROR(dev, "IO error : enable mipi rx fail.\n"); 685 else 686 DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n"); 687 688 return ret; 689 } 690 691 static int anx7625_api_dpi_config(struct anx7625_data *ctx) 692 { 693 struct device *dev = &ctx->client->dev; 694 u16 freq = ctx->dt.pixelclock.min / 1000; 695 int ret; 696 697 /* configure pixel clock */ 698 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 699 PIXEL_CLOCK_L, freq & 0xFF); 700 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 701 PIXEL_CLOCK_H, (freq >> 8)); 702 703 /* set DPI mode */ 704 /* set to DPI PLL module sel */ 705 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 706 MIPI_DIGITAL_PLL_9, 0x20); 707 /* power down MIPI */ 708 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 709 MIPI_LANE_CTRL_10, 0x08); 710 /* enable DPI mode */ 711 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 712 MIPI_DIGITAL_PLL_18, 0x1C); 713 /* set first edge */ 714 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 715 VIDEO_CONTROL_0, 0x06); 716 if (ret < 0) 717 DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); 718 719 return ret; 720 } 721 722 static int anx7625_dpi_config(struct anx7625_data *ctx) 723 { 724 struct device *dev = &ctx->client->dev; 725 int ret; 726 727 DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); 728 729 /* DSC disable */ 730 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 731 R_DSC_CTRL_0, ~DSC_EN); 732 if (ret < 0) { 733 DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); 734 return ret; 735 } 736 737 ret = anx7625_config_bit_matrix(ctx); 738 if (ret < 0) { 739 DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); 740 return ret; 741 } 742 743 ret = anx7625_api_dpi_config(ctx); 744 if (ret < 0) { 745 DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); 746 return ret; 747 } 748 749 /* set MIPI RX EN */ 750 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 751 AP_AV_STATUS, AP_MIPI_RX_EN); 752 /* clear mute flag */ 753 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 754 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 755 if (ret < 0) 756 DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); 757 758 return ret; 759 } 760 761 static int anx7625_read_flash_status(struct anx7625_data *ctx) 762 { 763 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, R_RAM_CTRL); 764 } 765 766 static int anx7625_hdcp_key_probe(struct anx7625_data *ctx) 767 { 768 int ret, val; 769 struct device *dev = &ctx->client->dev; 770 u8 ident[FLASH_BUF_LEN]; 771 772 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 773 FLASH_ADDR_HIGH, 0x91); 774 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 775 FLASH_ADDR_LOW, 0xA0); 776 if (ret < 0) { 777 dev_err(dev, "IO error : set key flash address.\n"); 778 return ret; 779 } 780 781 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 782 FLASH_LEN_HIGH, (FLASH_BUF_LEN - 1) >> 8); 783 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 784 FLASH_LEN_LOW, (FLASH_BUF_LEN - 1) & 0xFF); 785 if (ret < 0) { 786 dev_err(dev, "IO error : set key flash len.\n"); 787 return ret; 788 } 789 790 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 791 R_FLASH_RW_CTRL, FLASH_READ); 792 ret |= readx_poll_timeout(anx7625_read_flash_status, 793 ctx, val, 794 ((val & FLASH_DONE) || (val < 0)), 795 2000, 796 2000 * 150); 797 if (ret) { 798 dev_err(dev, "flash read access fail!\n"); 799 return -EIO; 800 } 801 802 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 803 FLASH_BUF_BASE_ADDR, 804 FLASH_BUF_LEN, ident); 805 if (ret < 0) { 806 dev_err(dev, "read flash data fail!\n"); 807 return -EIO; 808 } 809 810 if (ident[29] == 0xFF && ident[30] == 0xFF && ident[31] == 0xFF) 811 return -EINVAL; 812 813 return 0; 814 } 815 816 static int anx7625_hdcp_key_load(struct anx7625_data *ctx) 817 { 818 int ret; 819 struct device *dev = &ctx->client->dev; 820 821 /* Select HDCP 1.4 KEY */ 822 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 823 R_BOOT_RETRY, 0x12); 824 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 825 FLASH_ADDR_HIGH, HDCP14KEY_START_ADDR >> 8); 826 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 827 FLASH_ADDR_LOW, HDCP14KEY_START_ADDR & 0xFF); 828 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 829 R_RAM_LEN_H, HDCP14KEY_SIZE >> 12); 830 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 831 R_RAM_LEN_L, HDCP14KEY_SIZE >> 4); 832 833 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 834 R_RAM_ADDR_H, 0); 835 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 836 R_RAM_ADDR_L, 0); 837 /* Enable HDCP 1.4 KEY load */ 838 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 839 R_RAM_CTRL, DECRYPT_EN | LOAD_START); 840 dev_dbg(dev, "load HDCP 1.4 key done\n"); 841 return ret; 842 } 843 844 static int anx7625_hdcp_disable(struct anx7625_data *ctx) 845 { 846 int ret; 847 struct device *dev = &ctx->client->dev; 848 849 dev_dbg(dev, "disable HDCP 1.4\n"); 850 851 /* Disable HDCP */ 852 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 853 /* Try auth flag */ 854 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 855 /* Interrupt for DRM */ 856 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 857 if (ret < 0) 858 dev_err(dev, "fail to disable HDCP\n"); 859 860 return anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 861 TX_HDCP_CTRL0, ~HARD_AUTH_EN & 0xFF); 862 } 863 864 static int anx7625_hdcp_enable(struct anx7625_data *ctx) 865 { 866 u8 bcap; 867 int ret; 868 struct device *dev = &ctx->client->dev; 869 870 ret = anx7625_hdcp_key_probe(ctx); 871 if (ret) { 872 dev_dbg(dev, "no key found, not to do hdcp\n"); 873 return ret; 874 } 875 876 /* Read downstream capability */ 877 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_READ, 0x68028, 1, &bcap); 878 if (ret < 0) 879 return ret; 880 881 if (!(bcap & 0x01)) { 882 pr_warn("downstream not support HDCP 1.4, cap(%x).\n", bcap); 883 return 0; 884 } 885 886 dev_dbg(dev, "enable HDCP 1.4\n"); 887 888 /* First clear HDCP state */ 889 ret = anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 890 TX_HDCP_CTRL0, 891 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 892 usleep_range(1000, 1100); 893 /* Second clear HDCP state */ 894 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 895 TX_HDCP_CTRL0, 896 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 897 898 /* Set time for waiting KSVR */ 899 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 900 SP_TX_WAIT_KSVR_TIME, 0xc8); 901 /* Set time for waiting R0 */ 902 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 903 SP_TX_WAIT_R0_TIME, 0xb0); 904 ret |= anx7625_hdcp_key_load(ctx); 905 if (ret) { 906 pr_warn("prepare HDCP key failed.\n"); 907 return ret; 908 } 909 910 ret = anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20); 911 912 /* Try auth flag */ 913 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 914 /* Interrupt for DRM */ 915 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 916 if (ret < 0) 917 dev_err(dev, "fail to enable HDCP\n"); 918 919 return anx7625_write_or(ctx, ctx->i2c.tx_p0_client, 920 TX_HDCP_CTRL0, HARD_AUTH_EN); 921 } 922 923 static void anx7625_dp_start(struct anx7625_data *ctx) 924 { 925 int ret; 926 struct device *dev = &ctx->client->dev; 927 u8 data; 928 929 if (!ctx->display_timing_valid) { 930 DRM_DEV_ERROR(dev, "mipi not set display timing yet.\n"); 931 return; 932 } 933 934 dev_dbg(dev, "set downstream sink into normal\n"); 935 /* Downstream sink enter into normal mode */ 936 data = 1; 937 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, 0x000600, 1, &data); 938 if (ret < 0) 939 dev_err(dev, "IO error : set sink into normal mode fail\n"); 940 941 /* Disable HDCP */ 942 anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 943 944 if (ctx->pdata.is_dpi) 945 ret = anx7625_dpi_config(ctx); 946 else 947 ret = anx7625_dsi_config(ctx); 948 949 if (ret < 0) 950 DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); 951 952 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 953 954 ctx->dp_en = 1; 955 } 956 957 static void anx7625_dp_stop(struct anx7625_data *ctx) 958 { 959 struct device *dev = &ctx->client->dev; 960 int ret; 961 u8 data; 962 963 DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n"); 964 965 /* 966 * Video disable: 0x72:08 bit 7 = 0; 967 * Audio disable: 0x70:87 bit 0 = 0; 968 */ 969 ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe); 970 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f); 971 972 ret |= anx7625_video_mute_control(ctx, 1); 973 974 dev_dbg(dev, "notify downstream enter into standby\n"); 975 /* Downstream monitor enter into standby mode */ 976 data = 2; 977 ret |= anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, 0x000600, 1, &data); 978 if (ret < 0) 979 DRM_DEV_ERROR(dev, "IO error : mute video fail\n"); 980 981 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 982 983 ctx->dp_en = 0; 984 } 985 986 static int sp_tx_rst_aux(struct anx7625_data *ctx) 987 { 988 int ret; 989 990 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 991 AUX_RST); 992 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 993 ~AUX_RST); 994 return ret; 995 } 996 997 static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset) 998 { 999 int ret; 1000 1001 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1002 AP_AUX_BUFF_START, offset); 1003 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1004 AP_AUX_COMMAND, 0x04); 1005 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1006 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1007 return (ret | wait_aux_op_finish(ctx)); 1008 } 1009 1010 static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd) 1011 { 1012 int ret; 1013 1014 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1015 AP_AUX_COMMAND, len_cmd); 1016 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1017 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1018 return (ret | wait_aux_op_finish(ctx)); 1019 } 1020 1021 static int sp_tx_get_edid_block(struct anx7625_data *ctx) 1022 { 1023 int c = 0; 1024 struct device *dev = &ctx->client->dev; 1025 1026 sp_tx_aux_wr(ctx, 0x7e); 1027 sp_tx_aux_rd(ctx, 0x01); 1028 c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START); 1029 if (c < 0) { 1030 DRM_DEV_ERROR(dev, "IO error : access AUX BUFF.\n"); 1031 return -EIO; 1032 } 1033 1034 DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1); 1035 1036 if (c > MAX_EDID_BLOCK) 1037 c = 1; 1038 1039 return c; 1040 } 1041 1042 static int edid_read(struct anx7625_data *ctx, 1043 u8 offset, u8 *pblock_buf) 1044 { 1045 int ret, cnt; 1046 struct device *dev = &ctx->client->dev; 1047 1048 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1049 sp_tx_aux_wr(ctx, offset); 1050 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1051 ret = sp_tx_aux_rd(ctx, 0xf1); 1052 1053 if (ret) { 1054 ret = sp_tx_rst_aux(ctx); 1055 DRM_DEV_DEBUG_DRIVER(dev, "edid read fail, reset!\n"); 1056 } else { 1057 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1058 AP_AUX_BUFF_START, 1059 MAX_DPCD_BUFFER_SIZE, 1060 pblock_buf); 1061 if (ret > 0) 1062 break; 1063 } 1064 } 1065 1066 if (cnt > EDID_TRY_CNT) 1067 return -EIO; 1068 1069 return ret; 1070 } 1071 1072 static int segments_edid_read(struct anx7625_data *ctx, 1073 u8 segment, u8 *buf, u8 offset) 1074 { 1075 u8 cnt; 1076 int ret; 1077 struct device *dev = &ctx->client->dev; 1078 1079 /* Write address only */ 1080 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1081 AP_AUX_ADDR_7_0, 0x30); 1082 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1083 AP_AUX_COMMAND, 0x04); 1084 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1085 AP_AUX_CTRL_STATUS, 1086 AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN); 1087 1088 ret |= wait_aux_op_finish(ctx); 1089 /* Write segment address */ 1090 ret |= sp_tx_aux_wr(ctx, segment); 1091 /* Data read */ 1092 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1093 AP_AUX_ADDR_7_0, 0x50); 1094 if (ret) { 1095 DRM_DEV_ERROR(dev, "IO error : aux initial fail.\n"); 1096 return ret; 1097 } 1098 1099 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1100 sp_tx_aux_wr(ctx, offset); 1101 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1102 ret = sp_tx_aux_rd(ctx, 0xf1); 1103 1104 if (ret) { 1105 ret = sp_tx_rst_aux(ctx); 1106 DRM_DEV_ERROR(dev, "segment read fail, reset!\n"); 1107 } else { 1108 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1109 AP_AUX_BUFF_START, 1110 MAX_DPCD_BUFFER_SIZE, buf); 1111 if (ret > 0) 1112 break; 1113 } 1114 } 1115 1116 if (cnt > EDID_TRY_CNT) 1117 return -EIO; 1118 1119 return ret; 1120 } 1121 1122 static int sp_tx_edid_read(struct anx7625_data *ctx, 1123 u8 *pedid_blocks_buf) 1124 { 1125 u8 offset; 1126 int edid_pos; 1127 int count, blocks_num; 1128 u8 pblock_buf[MAX_DPCD_BUFFER_SIZE]; 1129 u8 i, j; 1130 int g_edid_break = 0; 1131 int ret; 1132 struct device *dev = &ctx->client->dev; 1133 1134 /* Address initial */ 1135 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1136 AP_AUX_ADDR_7_0, 0x50); 1137 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1138 AP_AUX_ADDR_15_8, 0); 1139 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 1140 AP_AUX_ADDR_19_16, 0xf0); 1141 if (ret < 0) { 1142 DRM_DEV_ERROR(dev, "access aux channel IO error.\n"); 1143 return -EIO; 1144 } 1145 1146 blocks_num = sp_tx_get_edid_block(ctx); 1147 if (blocks_num < 0) 1148 return blocks_num; 1149 1150 count = 0; 1151 1152 do { 1153 switch (count) { 1154 case 0: 1155 case 1: 1156 for (i = 0; i < 8; i++) { 1157 offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE; 1158 g_edid_break = edid_read(ctx, offset, 1159 pblock_buf); 1160 1161 if (g_edid_break < 0) 1162 break; 1163 1164 memcpy(&pedid_blocks_buf[offset], 1165 pblock_buf, 1166 MAX_DPCD_BUFFER_SIZE); 1167 } 1168 1169 break; 1170 case 2: 1171 offset = 0x00; 1172 1173 for (j = 0; j < 8; j++) { 1174 edid_pos = (j + count * 8) * 1175 MAX_DPCD_BUFFER_SIZE; 1176 1177 if (g_edid_break == 1) 1178 break; 1179 1180 ret = segments_edid_read(ctx, count / 2, 1181 pblock_buf, offset); 1182 if (ret < 0) 1183 return ret; 1184 1185 memcpy(&pedid_blocks_buf[edid_pos], 1186 pblock_buf, 1187 MAX_DPCD_BUFFER_SIZE); 1188 offset = offset + 0x10; 1189 } 1190 1191 break; 1192 case 3: 1193 offset = 0x80; 1194 1195 for (j = 0; j < 8; j++) { 1196 edid_pos = (j + count * 8) * 1197 MAX_DPCD_BUFFER_SIZE; 1198 if (g_edid_break == 1) 1199 break; 1200 1201 ret = segments_edid_read(ctx, count / 2, 1202 pblock_buf, offset); 1203 if (ret < 0) 1204 return ret; 1205 1206 memcpy(&pedid_blocks_buf[edid_pos], 1207 pblock_buf, 1208 MAX_DPCD_BUFFER_SIZE); 1209 offset = offset + 0x10; 1210 } 1211 1212 break; 1213 default: 1214 break; 1215 } 1216 1217 count++; 1218 1219 } while (blocks_num >= count); 1220 1221 /* Check edid data */ 1222 if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) { 1223 DRM_DEV_ERROR(dev, "WARNING! edid check fail!\n"); 1224 return -EINVAL; 1225 } 1226 1227 /* Reset aux channel */ 1228 ret = sp_tx_rst_aux(ctx); 1229 if (ret < 0) { 1230 DRM_DEV_ERROR(dev, "Failed to reset aux channel!\n"); 1231 return ret; 1232 } 1233 1234 return (blocks_num + 1); 1235 } 1236 1237 static void anx7625_power_on(struct anx7625_data *ctx) 1238 { 1239 struct device *dev = &ctx->client->dev; 1240 int ret, i; 1241 1242 if (!ctx->pdata.low_power_mode) { 1243 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1244 return; 1245 } 1246 1247 for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) { 1248 ret = regulator_enable(ctx->pdata.supplies[i].consumer); 1249 if (ret < 0) { 1250 DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n", 1251 i, ret); 1252 goto reg_err; 1253 } 1254 usleep_range(2000, 2100); 1255 } 1256 1257 usleep_range(11000, 12000); 1258 1259 /* Power on pin enable */ 1260 gpiod_set_value(ctx->pdata.gpio_p_on, 1); 1261 usleep_range(10000, 11000); 1262 /* Power reset pin enable */ 1263 gpiod_set_value(ctx->pdata.gpio_reset, 1); 1264 usleep_range(10000, 11000); 1265 1266 DRM_DEV_DEBUG_DRIVER(dev, "power on !\n"); 1267 return; 1268 reg_err: 1269 for (--i; i >= 0; i--) 1270 regulator_disable(ctx->pdata.supplies[i].consumer); 1271 } 1272 1273 static void anx7625_power_standby(struct anx7625_data *ctx) 1274 { 1275 struct device *dev = &ctx->client->dev; 1276 int ret; 1277 1278 if (!ctx->pdata.low_power_mode) { 1279 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1280 return; 1281 } 1282 1283 gpiod_set_value(ctx->pdata.gpio_reset, 0); 1284 usleep_range(1000, 1100); 1285 gpiod_set_value(ctx->pdata.gpio_p_on, 0); 1286 usleep_range(1000, 1100); 1287 1288 ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies), 1289 ctx->pdata.supplies); 1290 if (ret < 0) 1291 DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret); 1292 1293 DRM_DEV_DEBUG_DRIVER(dev, "power down\n"); 1294 } 1295 1296 /* Basic configurations of ANX7625 */ 1297 static void anx7625_config(struct anx7625_data *ctx) 1298 { 1299 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1300 XTAL_FRQ_SEL, XTAL_FRQ_27M); 1301 } 1302 1303 static void anx7625_disable_pd_protocol(struct anx7625_data *ctx) 1304 { 1305 struct device *dev = &ctx->client->dev; 1306 int ret; 1307 1308 /* Reset main ocm */ 1309 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40); 1310 /* Disable PD */ 1311 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1312 AP_AV_STATUS, AP_DISABLE_PD); 1313 /* Release main ocm */ 1314 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00); 1315 1316 if (ret < 0) 1317 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature fail.\n"); 1318 else 1319 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n"); 1320 } 1321 1322 static int anx7625_ocm_loading_check(struct anx7625_data *ctx) 1323 { 1324 int ret; 1325 struct device *dev = &ctx->client->dev; 1326 1327 /* Check interface workable */ 1328 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1329 FLASH_LOAD_STA); 1330 if (ret < 0) { 1331 DRM_DEV_ERROR(dev, "IO error : access flash load.\n"); 1332 return ret; 1333 } 1334 if ((ret & FLASH_LOAD_STA_CHK) != FLASH_LOAD_STA_CHK) 1335 return -ENODEV; 1336 1337 anx7625_disable_pd_protocol(ctx); 1338 1339 DRM_DEV_DEBUG_DRIVER(dev, "Firmware ver %02x%02x,", 1340 anx7625_reg_read(ctx, 1341 ctx->i2c.rx_p0_client, 1342 OCM_FW_VERSION), 1343 anx7625_reg_read(ctx, 1344 ctx->i2c.rx_p0_client, 1345 OCM_FW_REVERSION)); 1346 DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n", 1347 ANX7625_DRV_VERSION); 1348 1349 return 0; 1350 } 1351 1352 static void anx7625_power_on_init(struct anx7625_data *ctx) 1353 { 1354 int retry_count, i; 1355 1356 for (retry_count = 0; retry_count < 3; retry_count++) { 1357 anx7625_power_on(ctx); 1358 anx7625_config(ctx); 1359 1360 for (i = 0; i < OCM_LOADING_TIME; i++) { 1361 if (!anx7625_ocm_loading_check(ctx)) 1362 return; 1363 usleep_range(1000, 1100); 1364 } 1365 anx7625_power_standby(ctx); 1366 } 1367 } 1368 1369 static void anx7625_init_gpio(struct anx7625_data *platform) 1370 { 1371 struct device *dev = &platform->client->dev; 1372 1373 DRM_DEV_DEBUG_DRIVER(dev, "init gpio\n"); 1374 1375 /* Gpio for chip power enable */ 1376 platform->pdata.gpio_p_on = 1377 devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); 1378 if (IS_ERR_OR_NULL(platform->pdata.gpio_p_on)) { 1379 DRM_DEV_DEBUG_DRIVER(dev, "no enable gpio found\n"); 1380 platform->pdata.gpio_p_on = NULL; 1381 } 1382 1383 /* Gpio for chip reset */ 1384 platform->pdata.gpio_reset = 1385 devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1386 if (IS_ERR_OR_NULL(platform->pdata.gpio_reset)) { 1387 DRM_DEV_DEBUG_DRIVER(dev, "no reset gpio found\n"); 1388 platform->pdata.gpio_reset = NULL; 1389 } 1390 1391 if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) { 1392 platform->pdata.low_power_mode = 1; 1393 DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n", 1394 desc_to_gpio(platform->pdata.gpio_p_on), 1395 desc_to_gpio(platform->pdata.gpio_reset)); 1396 } else { 1397 platform->pdata.low_power_mode = 0; 1398 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n"); 1399 } 1400 } 1401 1402 static void anx7625_stop_dp_work(struct anx7625_data *ctx) 1403 { 1404 ctx->hpd_status = 0; 1405 ctx->hpd_high_cnt = 0; 1406 ctx->display_timing_valid = 0; 1407 } 1408 1409 static void anx7625_start_dp_work(struct anx7625_data *ctx) 1410 { 1411 int ret; 1412 struct device *dev = &ctx->client->dev; 1413 1414 if (ctx->hpd_high_cnt >= 2) { 1415 DRM_DEV_DEBUG_DRIVER(dev, "filter useless HPD\n"); 1416 return; 1417 } 1418 1419 ctx->hpd_status = 1; 1420 ctx->hpd_high_cnt++; 1421 1422 /* Not support HDCP */ 1423 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 1424 1425 /* Try auth flag */ 1426 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 1427 /* Interrupt for DRM */ 1428 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 1429 if (ret < 0) { 1430 DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); 1431 return; 1432 } 1433 1434 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); 1435 if (ret < 0) 1436 return; 1437 1438 DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret); 1439 } 1440 1441 static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx) 1442 { 1443 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS); 1444 } 1445 1446 static void anx7625_hpd_polling(struct anx7625_data *ctx) 1447 { 1448 int ret, val; 1449 struct device *dev = &ctx->client->dev; 1450 1451 /* Interrupt mode, no need poll HPD status, just return */ 1452 if (ctx->pdata.intp_irq) 1453 return; 1454 1455 ret = readx_poll_timeout(anx7625_read_hpd_status_p0, 1456 ctx, val, 1457 ((val & HPD_STATUS) || (val < 0)), 1458 5000, 1459 5000 * 100); 1460 if (ret) { 1461 DRM_DEV_ERROR(dev, "no hpd.\n"); 1462 return; 1463 } 1464 1465 DRM_DEV_DEBUG_DRIVER(dev, "system status: 0x%x. HPD raise up.\n", val); 1466 anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1467 INTR_ALERT_1, 0xFF); 1468 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1469 INTERFACE_CHANGE_INT, 0); 1470 1471 anx7625_start_dp_work(ctx); 1472 1473 if (!ctx->pdata.panel_bridge && ctx->bridge_attached) 1474 drm_helper_hpd_irq_event(ctx->bridge.dev); 1475 } 1476 1477 static void anx7625_remove_edid(struct anx7625_data *ctx) 1478 { 1479 ctx->slimport_edid_p.edid_block_num = -1; 1480 } 1481 1482 static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) 1483 { 1484 int i; 1485 1486 for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) 1487 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1488 DP_TX_LANE0_SWING_REG0 + i, 1489 ctx->pdata.lane0_reg_data[i]); 1490 1491 for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) 1492 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1493 DP_TX_LANE1_SWING_REG0 + i, 1494 ctx->pdata.lane1_reg_data[i]); 1495 } 1496 1497 static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) 1498 { 1499 struct device *dev = &ctx->client->dev; 1500 1501 /* HPD changed */ 1502 DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n", 1503 (u32)on); 1504 1505 if (on == 0) { 1506 DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n"); 1507 anx7625_remove_edid(ctx); 1508 anx7625_stop_dp_work(ctx); 1509 } else { 1510 DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); 1511 anx7625_start_dp_work(ctx); 1512 anx7625_dp_adjust_swing(ctx); 1513 } 1514 } 1515 1516 static int anx7625_hpd_change_detect(struct anx7625_data *ctx) 1517 { 1518 int intr_vector, status; 1519 struct device *dev = &ctx->client->dev; 1520 1521 status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1522 INTR_ALERT_1, 0xFF); 1523 if (status < 0) { 1524 DRM_DEV_ERROR(dev, "cannot clear alert reg.\n"); 1525 return status; 1526 } 1527 1528 intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1529 INTERFACE_CHANGE_INT); 1530 if (intr_vector < 0) { 1531 DRM_DEV_ERROR(dev, "cannot access interrupt change reg.\n"); 1532 return intr_vector; 1533 } 1534 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector); 1535 status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1536 INTERFACE_CHANGE_INT, 1537 intr_vector & (~intr_vector)); 1538 if (status < 0) { 1539 DRM_DEV_ERROR(dev, "cannot clear interrupt change reg.\n"); 1540 return status; 1541 } 1542 1543 if (!(intr_vector & HPD_STATUS_CHANGE)) 1544 return -ENOENT; 1545 1546 status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1547 SYSTEM_STSTUS); 1548 if (status < 0) { 1549 DRM_DEV_ERROR(dev, "cannot clear interrupt status.\n"); 1550 return status; 1551 } 1552 1553 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status); 1554 dp_hpd_change_handler(ctx, status & HPD_STATUS); 1555 1556 return 0; 1557 } 1558 1559 static void anx7625_work_func(struct work_struct *work) 1560 { 1561 int event; 1562 struct anx7625_data *ctx = container_of(work, 1563 struct anx7625_data, work); 1564 1565 mutex_lock(&ctx->lock); 1566 1567 if (pm_runtime_suspended(&ctx->client->dev)) 1568 goto unlock; 1569 1570 event = anx7625_hpd_change_detect(ctx); 1571 if (event < 0) 1572 goto unlock; 1573 1574 if (ctx->bridge_attached) 1575 drm_helper_hpd_irq_event(ctx->bridge.dev); 1576 1577 unlock: 1578 mutex_unlock(&ctx->lock); 1579 } 1580 1581 static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) 1582 { 1583 struct anx7625_data *ctx = (struct anx7625_data *)data; 1584 1585 queue_work(ctx->workqueue, &ctx->work); 1586 1587 return IRQ_HANDLED; 1588 } 1589 1590 static int anx7625_get_swing_setting(struct device *dev, 1591 struct anx7625_platform_data *pdata) 1592 { 1593 int num_regs; 1594 1595 if (of_get_property(dev->of_node, 1596 "analogix,lane0-swing", &num_regs)) { 1597 if (num_regs > DP_TX_SWING_REG_CNT) 1598 num_regs = DP_TX_SWING_REG_CNT; 1599 1600 pdata->dp_lane0_swing_reg_cnt = num_regs; 1601 of_property_read_u8_array(dev->of_node, "analogix,lane0-swing", 1602 pdata->lane0_reg_data, num_regs); 1603 } 1604 1605 if (of_get_property(dev->of_node, 1606 "analogix,lane1-swing", &num_regs)) { 1607 if (num_regs > DP_TX_SWING_REG_CNT) 1608 num_regs = DP_TX_SWING_REG_CNT; 1609 1610 pdata->dp_lane1_swing_reg_cnt = num_regs; 1611 of_property_read_u8_array(dev->of_node, "analogix,lane1-swing", 1612 pdata->lane1_reg_data, num_regs); 1613 } 1614 1615 return 0; 1616 } 1617 1618 static int anx7625_parse_dt(struct device *dev, 1619 struct anx7625_platform_data *pdata) 1620 { 1621 struct device_node *np = dev->of_node, *ep0; 1622 int bus_type, mipi_lanes; 1623 1624 anx7625_get_swing_setting(dev, pdata); 1625 1626 pdata->is_dpi = 1; /* default dpi mode */ 1627 pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); 1628 if (!pdata->mipi_host_node) { 1629 DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); 1630 return -ENODEV; 1631 } 1632 1633 bus_type = V4L2_FWNODE_BUS_TYPE_PARALLEL; 1634 mipi_lanes = MAX_LANES_SUPPORT; 1635 ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); 1636 if (ep0) { 1637 if (of_property_read_u32(ep0, "bus-type", &bus_type)) 1638 bus_type = 0; 1639 1640 mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes"); 1641 of_node_put(ep0); 1642 } 1643 1644 if (bus_type == V4L2_FWNODE_BUS_TYPE_PARALLEL) /* bus type is Parallel(DSI) */ 1645 pdata->is_dpi = 0; 1646 1647 pdata->mipi_lanes = mipi_lanes; 1648 if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0) 1649 pdata->mipi_lanes = MAX_LANES_SUPPORT; 1650 1651 if (pdata->is_dpi) 1652 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); 1653 else 1654 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); 1655 1656 if (of_property_read_bool(np, "analogix,audio-enable")) 1657 pdata->audio_en = 1; 1658 1659 pdata->panel_bridge = devm_drm_of_get_bridge(dev, np, 1, 0); 1660 if (IS_ERR(pdata->panel_bridge)) { 1661 if (PTR_ERR(pdata->panel_bridge) == -ENODEV) 1662 return 0; 1663 1664 return PTR_ERR(pdata->panel_bridge); 1665 } 1666 1667 DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n"); 1668 1669 return 0; 1670 } 1671 1672 static bool anx7625_of_panel_on_aux_bus(struct device *dev) 1673 { 1674 struct device_node *bus, *panel; 1675 1676 bus = of_get_child_by_name(dev->of_node, "aux-bus"); 1677 if (!bus) 1678 return false; 1679 1680 panel = of_get_child_by_name(bus, "panel"); 1681 of_node_put(bus); 1682 if (!panel) 1683 return false; 1684 of_node_put(panel); 1685 1686 return true; 1687 } 1688 1689 static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge) 1690 { 1691 return container_of(bridge, struct anx7625_data, bridge); 1692 } 1693 1694 static ssize_t anx7625_aux_transfer(struct drm_dp_aux *aux, 1695 struct drm_dp_aux_msg *msg) 1696 { 1697 struct anx7625_data *ctx = container_of(aux, struct anx7625_data, aux); 1698 struct device *dev = &ctx->client->dev; 1699 u8 request = msg->request & ~DP_AUX_I2C_MOT; 1700 int ret = 0; 1701 1702 pm_runtime_get_sync(dev); 1703 msg->reply = 0; 1704 switch (request) { 1705 case DP_AUX_NATIVE_WRITE: 1706 case DP_AUX_I2C_WRITE: 1707 case DP_AUX_NATIVE_READ: 1708 case DP_AUX_I2C_READ: 1709 break; 1710 default: 1711 ret = -EINVAL; 1712 } 1713 if (!ret) 1714 ret = anx7625_aux_trans(ctx, msg->request, msg->address, 1715 msg->size, msg->buffer); 1716 pm_runtime_mark_last_busy(dev); 1717 pm_runtime_put_autosuspend(dev); 1718 1719 return ret; 1720 } 1721 1722 static struct edid *anx7625_get_edid(struct anx7625_data *ctx) 1723 { 1724 struct device *dev = &ctx->client->dev; 1725 struct s_edid_data *p_edid = &ctx->slimport_edid_p; 1726 int edid_num; 1727 u8 *edid; 1728 1729 edid = kmalloc(FOUR_BLOCK_SIZE, GFP_KERNEL); 1730 if (!edid) { 1731 DRM_DEV_ERROR(dev, "Fail to allocate buffer\n"); 1732 return NULL; 1733 } 1734 1735 if (ctx->slimport_edid_p.edid_block_num > 0) { 1736 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, 1737 FOUR_BLOCK_SIZE); 1738 return (struct edid *)edid; 1739 } 1740 1741 pm_runtime_get_sync(dev); 1742 edid_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data); 1743 pm_runtime_put_sync(dev); 1744 1745 if (edid_num < 1) { 1746 DRM_DEV_ERROR(dev, "Fail to read EDID: %d\n", edid_num); 1747 kfree(edid); 1748 return NULL; 1749 } 1750 1751 p_edid->edid_block_num = edid_num; 1752 1753 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, FOUR_BLOCK_SIZE); 1754 return (struct edid *)edid; 1755 } 1756 1757 static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) 1758 { 1759 struct device *dev = &ctx->client->dev; 1760 1761 DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); 1762 1763 if (ctx->pdata.panel_bridge) 1764 return connector_status_connected; 1765 1766 return ctx->hpd_status ? connector_status_connected : 1767 connector_status_disconnected; 1768 } 1769 1770 static int anx7625_audio_hw_params(struct device *dev, void *data, 1771 struct hdmi_codec_daifmt *fmt, 1772 struct hdmi_codec_params *params) 1773 { 1774 struct anx7625_data *ctx = dev_get_drvdata(dev); 1775 int wl, ch, rate; 1776 int ret = 0; 1777 1778 if (fmt->fmt != HDMI_DSP_A) { 1779 DRM_DEV_ERROR(dev, "only supports DSP_A\n"); 1780 return -EINVAL; 1781 } 1782 1783 DRM_DEV_DEBUG_DRIVER(dev, "setting %d Hz, %d bit, %d channels\n", 1784 params->sample_rate, params->sample_width, 1785 params->cea.channels); 1786 1787 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1788 AUDIO_CHANNEL_STATUS_6, 1789 ~I2S_SLAVE_MODE, 1790 TDM_SLAVE_MODE); 1791 1792 /* Word length */ 1793 switch (params->sample_width) { 1794 case 16: 1795 wl = AUDIO_W_LEN_16_20MAX; 1796 break; 1797 case 18: 1798 wl = AUDIO_W_LEN_18_20MAX; 1799 break; 1800 case 20: 1801 wl = AUDIO_W_LEN_20_20MAX; 1802 break; 1803 case 24: 1804 wl = AUDIO_W_LEN_24_24MAX; 1805 break; 1806 default: 1807 DRM_DEV_DEBUG_DRIVER(dev, "wordlength: %d bit not support", 1808 params->sample_width); 1809 return -EINVAL; 1810 } 1811 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1812 AUDIO_CHANNEL_STATUS_5, 1813 0xf0, wl); 1814 1815 /* Channel num */ 1816 switch (params->cea.channels) { 1817 case 2: 1818 ch = I2S_CH_2; 1819 break; 1820 case 4: 1821 ch = TDM_CH_4; 1822 break; 1823 case 6: 1824 ch = TDM_CH_6; 1825 break; 1826 case 8: 1827 ch = TDM_CH_8; 1828 break; 1829 default: 1830 DRM_DEV_DEBUG_DRIVER(dev, "channel number: %d not support", 1831 params->cea.channels); 1832 return -EINVAL; 1833 } 1834 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1835 AUDIO_CHANNEL_STATUS_6, 0x1f, ch << 5); 1836 if (ch > I2S_CH_2) 1837 ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 1838 AUDIO_CHANNEL_STATUS_6, AUDIO_LAYOUT); 1839 else 1840 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 1841 AUDIO_CHANNEL_STATUS_6, ~AUDIO_LAYOUT); 1842 1843 /* FS */ 1844 switch (params->sample_rate) { 1845 case 32000: 1846 rate = AUDIO_FS_32K; 1847 break; 1848 case 44100: 1849 rate = AUDIO_FS_441K; 1850 break; 1851 case 48000: 1852 rate = AUDIO_FS_48K; 1853 break; 1854 case 88200: 1855 rate = AUDIO_FS_882K; 1856 break; 1857 case 96000: 1858 rate = AUDIO_FS_96K; 1859 break; 1860 case 176400: 1861 rate = AUDIO_FS_1764K; 1862 break; 1863 case 192000: 1864 rate = AUDIO_FS_192K; 1865 break; 1866 default: 1867 DRM_DEV_DEBUG_DRIVER(dev, "sample rate: %d not support", 1868 params->sample_rate); 1869 return -EINVAL; 1870 } 1871 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1872 AUDIO_CHANNEL_STATUS_4, 1873 0xf0, rate); 1874 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1875 AP_AV_STATUS, AP_AUDIO_CHG); 1876 if (ret < 0) { 1877 DRM_DEV_ERROR(dev, "IO error : config audio.\n"); 1878 return -EIO; 1879 } 1880 1881 return 0; 1882 } 1883 1884 static void anx7625_audio_shutdown(struct device *dev, void *data) 1885 { 1886 DRM_DEV_DEBUG_DRIVER(dev, "stop audio\n"); 1887 } 1888 1889 static int anx7625_hdmi_i2s_get_dai_id(struct snd_soc_component *component, 1890 struct device_node *endpoint) 1891 { 1892 struct of_endpoint of_ep; 1893 int ret; 1894 1895 ret = of_graph_parse_endpoint(endpoint, &of_ep); 1896 if (ret < 0) 1897 return ret; 1898 1899 /* 1900 * HDMI sound should be located at external DPI port 1901 * Didn't have good way to check where is internal(DSI) 1902 * or external(DPI) bridge 1903 */ 1904 return 0; 1905 } 1906 1907 static void 1908 anx7625_audio_update_connector_status(struct anx7625_data *ctx, 1909 enum drm_connector_status status) 1910 { 1911 if (ctx->plugged_cb && ctx->codec_dev) { 1912 ctx->plugged_cb(ctx->codec_dev, 1913 status == connector_status_connected); 1914 } 1915 } 1916 1917 static int anx7625_audio_hook_plugged_cb(struct device *dev, void *data, 1918 hdmi_codec_plugged_cb fn, 1919 struct device *codec_dev) 1920 { 1921 struct anx7625_data *ctx = data; 1922 1923 ctx->plugged_cb = fn; 1924 ctx->codec_dev = codec_dev; 1925 anx7625_audio_update_connector_status(ctx, anx7625_sink_detect(ctx)); 1926 1927 return 0; 1928 } 1929 1930 static int anx7625_audio_get_eld(struct device *dev, void *data, 1931 u8 *buf, size_t len) 1932 { 1933 struct anx7625_data *ctx = dev_get_drvdata(dev); 1934 1935 if (!ctx->connector) { 1936 /* Pass en empty ELD if connector not available */ 1937 memset(buf, 0, len); 1938 } else { 1939 dev_dbg(dev, "audio copy eld\n"); 1940 memcpy(buf, ctx->connector->eld, 1941 min(sizeof(ctx->connector->eld), len)); 1942 } 1943 1944 return 0; 1945 } 1946 1947 static const struct hdmi_codec_ops anx7625_codec_ops = { 1948 .hw_params = anx7625_audio_hw_params, 1949 .audio_shutdown = anx7625_audio_shutdown, 1950 .get_eld = anx7625_audio_get_eld, 1951 .get_dai_id = anx7625_hdmi_i2s_get_dai_id, 1952 .hook_plugged_cb = anx7625_audio_hook_plugged_cb, 1953 }; 1954 1955 static void anx7625_unregister_audio(struct anx7625_data *ctx) 1956 { 1957 struct device *dev = &ctx->client->dev; 1958 1959 if (ctx->audio_pdev) { 1960 platform_device_unregister(ctx->audio_pdev); 1961 ctx->audio_pdev = NULL; 1962 } 1963 1964 DRM_DEV_DEBUG_DRIVER(dev, "unbound to %s", HDMI_CODEC_DRV_NAME); 1965 } 1966 1967 static int anx7625_register_audio(struct device *dev, struct anx7625_data *ctx) 1968 { 1969 struct hdmi_codec_pdata codec_data = { 1970 .ops = &anx7625_codec_ops, 1971 .max_i2s_channels = 8, 1972 .i2s = 1, 1973 .data = ctx, 1974 }; 1975 1976 ctx->audio_pdev = platform_device_register_data(dev, 1977 HDMI_CODEC_DRV_NAME, 1978 PLATFORM_DEVID_AUTO, 1979 &codec_data, 1980 sizeof(codec_data)); 1981 1982 if (IS_ERR(ctx->audio_pdev)) 1983 return PTR_ERR(ctx->audio_pdev); 1984 1985 DRM_DEV_DEBUG_DRIVER(dev, "bound to %s", HDMI_CODEC_DRV_NAME); 1986 1987 return 0; 1988 } 1989 1990 static int anx7625_attach_dsi(struct anx7625_data *ctx) 1991 { 1992 struct mipi_dsi_device *dsi; 1993 struct device *dev = &ctx->client->dev; 1994 struct mipi_dsi_host *host; 1995 const struct mipi_dsi_device_info info = { 1996 .type = "anx7625", 1997 .channel = 0, 1998 .node = NULL, 1999 }; 2000 int ret; 2001 2002 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n"); 2003 2004 host = of_find_mipi_dsi_host_by_node(ctx->pdata.mipi_host_node); 2005 if (!host) { 2006 DRM_DEV_ERROR(dev, "fail to find dsi host.\n"); 2007 return -EPROBE_DEFER; 2008 } 2009 2010 dsi = devm_mipi_dsi_device_register_full(dev, host, &info); 2011 if (IS_ERR(dsi)) { 2012 DRM_DEV_ERROR(dev, "fail to create dsi device.\n"); 2013 return -EINVAL; 2014 } 2015 2016 dsi->lanes = ctx->pdata.mipi_lanes; 2017 dsi->format = MIPI_DSI_FMT_RGB888; 2018 dsi->mode_flags = MIPI_DSI_MODE_VIDEO | 2019 MIPI_DSI_MODE_VIDEO_SYNC_PULSE | 2020 MIPI_DSI_MODE_VIDEO_HSE | 2021 MIPI_DSI_HS_PKT_END_ALIGNED; 2022 2023 ret = devm_mipi_dsi_attach(dev, dsi); 2024 if (ret) { 2025 DRM_DEV_ERROR(dev, "fail to attach dsi to host.\n"); 2026 return ret; 2027 } 2028 2029 ctx->dsi = dsi; 2030 2031 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n"); 2032 2033 return 0; 2034 } 2035 2036 static void hdcp_check_work_func(struct work_struct *work) 2037 { 2038 u8 status; 2039 struct delayed_work *dwork; 2040 struct anx7625_data *ctx; 2041 struct device *dev; 2042 struct drm_device *drm_dev; 2043 2044 dwork = to_delayed_work(work); 2045 ctx = container_of(dwork, struct anx7625_data, hdcp_work); 2046 dev = &ctx->client->dev; 2047 2048 if (!ctx->connector) { 2049 dev_err(dev, "HDCP connector is null!"); 2050 return; 2051 } 2052 2053 drm_dev = ctx->connector->dev; 2054 drm_modeset_lock(&drm_dev->mode_config.connection_mutex, NULL); 2055 mutex_lock(&ctx->hdcp_wq_lock); 2056 2057 status = anx7625_reg_read(ctx, ctx->i2c.tx_p0_client, 0); 2058 dev_dbg(dev, "sink HDCP status check: %.02x\n", status); 2059 if (status & BIT(1)) { 2060 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_ENABLED; 2061 drm_hdcp_update_content_protection(ctx->connector, 2062 ctx->hdcp_cp); 2063 dev_dbg(dev, "update CP to ENABLE\n"); 2064 } 2065 2066 mutex_unlock(&ctx->hdcp_wq_lock); 2067 drm_modeset_unlock(&drm_dev->mode_config.connection_mutex); 2068 } 2069 2070 static int anx7625_connector_atomic_check(struct anx7625_data *ctx, 2071 struct drm_connector_state *state) 2072 { 2073 struct device *dev = &ctx->client->dev; 2074 int cp; 2075 2076 dev_dbg(dev, "hdcp state check\n"); 2077 cp = state->content_protection; 2078 2079 if (cp == ctx->hdcp_cp) 2080 return 0; 2081 2082 if (cp == DRM_MODE_CONTENT_PROTECTION_DESIRED) { 2083 if (ctx->dp_en) { 2084 dev_dbg(dev, "enable HDCP\n"); 2085 anx7625_hdcp_enable(ctx); 2086 2087 queue_delayed_work(ctx->hdcp_workqueue, 2088 &ctx->hdcp_work, 2089 msecs_to_jiffies(2000)); 2090 } 2091 } 2092 2093 if (cp == DRM_MODE_CONTENT_PROTECTION_UNDESIRED) { 2094 if (ctx->hdcp_cp != DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2095 dev_err(dev, "current CP is not ENABLED\n"); 2096 return -EINVAL; 2097 } 2098 anx7625_hdcp_disable(ctx); 2099 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 2100 drm_hdcp_update_content_protection(ctx->connector, 2101 ctx->hdcp_cp); 2102 dev_dbg(dev, "update CP to UNDESIRE\n"); 2103 } 2104 2105 if (cp == DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2106 dev_err(dev, "Userspace illegal set to PROTECTION ENABLE\n"); 2107 return -EINVAL; 2108 } 2109 2110 return 0; 2111 } 2112 2113 static int anx7625_bridge_attach(struct drm_bridge *bridge, 2114 enum drm_bridge_attach_flags flags) 2115 { 2116 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2117 int err; 2118 struct device *dev = &ctx->client->dev; 2119 2120 DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n"); 2121 if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) 2122 return -EINVAL; 2123 2124 if (!bridge->encoder) { 2125 DRM_DEV_ERROR(dev, "Parent encoder object not found"); 2126 return -ENODEV; 2127 } 2128 2129 ctx->aux.drm_dev = bridge->dev; 2130 err = drm_dp_aux_register(&ctx->aux); 2131 if (err) { 2132 dev_err(dev, "failed to register aux channel: %d\n", err); 2133 return err; 2134 } 2135 2136 if (ctx->pdata.panel_bridge) { 2137 err = drm_bridge_attach(bridge->encoder, 2138 ctx->pdata.panel_bridge, 2139 &ctx->bridge, flags); 2140 if (err) 2141 return err; 2142 } 2143 2144 ctx->bridge_attached = 1; 2145 2146 return 0; 2147 } 2148 2149 static void anx7625_bridge_detach(struct drm_bridge *bridge) 2150 { 2151 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2152 2153 drm_dp_aux_unregister(&ctx->aux); 2154 } 2155 2156 static enum drm_mode_status 2157 anx7625_bridge_mode_valid(struct drm_bridge *bridge, 2158 const struct drm_display_info *info, 2159 const struct drm_display_mode *mode) 2160 { 2161 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2162 struct device *dev = &ctx->client->dev; 2163 2164 DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n"); 2165 2166 /* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */ 2167 if (mode->clock > SUPPORT_PIXEL_CLOCK) { 2168 DRM_DEV_DEBUG_DRIVER(dev, 2169 "drm mode invalid, pixelclock too high.\n"); 2170 return MODE_CLOCK_HIGH; 2171 } 2172 2173 DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n"); 2174 2175 return MODE_OK; 2176 } 2177 2178 static void anx7625_bridge_mode_set(struct drm_bridge *bridge, 2179 const struct drm_display_mode *old_mode, 2180 const struct drm_display_mode *mode) 2181 { 2182 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2183 struct device *dev = &ctx->client->dev; 2184 2185 DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n"); 2186 2187 ctx->dt.pixelclock.min = mode->clock; 2188 ctx->dt.hactive.min = mode->hdisplay; 2189 ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start; 2190 ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay; 2191 ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end; 2192 ctx->dt.vactive.min = mode->vdisplay; 2193 ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start; 2194 ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay; 2195 ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end; 2196 2197 ctx->display_timing_valid = 1; 2198 2199 DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min); 2200 DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n", 2201 ctx->dt.hactive.min, 2202 ctx->dt.hsync_len.min, 2203 ctx->dt.hfront_porch.min, 2204 ctx->dt.hback_porch.min); 2205 DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n", 2206 ctx->dt.vactive.min, 2207 ctx->dt.vsync_len.min, 2208 ctx->dt.vfront_porch.min, 2209 ctx->dt.vback_porch.min); 2210 DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n", 2211 mode->hdisplay, 2212 mode->hsync_start); 2213 DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n", 2214 mode->hsync_end, 2215 mode->htotal); 2216 DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n", 2217 mode->vdisplay, 2218 mode->vsync_start); 2219 DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n", 2220 mode->vsync_end, 2221 mode->vtotal); 2222 } 2223 2224 static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, 2225 const struct drm_display_mode *mode, 2226 struct drm_display_mode *adj) 2227 { 2228 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2229 struct device *dev = &ctx->client->dev; 2230 u32 hsync, hfp, hbp, hblanking; 2231 u32 adj_hsync, adj_hfp, adj_hbp, adj_hblanking, delta_adj; 2232 u32 vref, adj_clock; 2233 2234 DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); 2235 2236 /* No need fixup for external monitor */ 2237 if (!ctx->pdata.panel_bridge) 2238 return true; 2239 2240 hsync = mode->hsync_end - mode->hsync_start; 2241 hfp = mode->hsync_start - mode->hdisplay; 2242 hbp = mode->htotal - mode->hsync_end; 2243 hblanking = mode->htotal - mode->hdisplay; 2244 2245 DRM_DEV_DEBUG_DRIVER(dev, "before mode fixup\n"); 2246 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2247 hsync, hfp, hbp, adj->clock); 2248 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2249 adj->hsync_start, adj->hsync_end, adj->htotal); 2250 2251 adj_hfp = hfp; 2252 adj_hsync = hsync; 2253 adj_hbp = hbp; 2254 adj_hblanking = hblanking; 2255 2256 /* HFP needs to be even */ 2257 if (hfp & 0x1) { 2258 adj_hfp += 1; 2259 adj_hblanking += 1; 2260 } 2261 2262 /* HBP needs to be even */ 2263 if (hbp & 0x1) { 2264 adj_hbp -= 1; 2265 adj_hblanking -= 1; 2266 } 2267 2268 /* HSYNC needs to be even */ 2269 if (hsync & 0x1) { 2270 if (adj_hblanking < hblanking) 2271 adj_hsync += 1; 2272 else 2273 adj_hsync -= 1; 2274 } 2275 2276 /* 2277 * Once illegal timing detected, use default HFP, HSYNC, HBP 2278 * This adjusting made for built-in eDP panel, for the externel 2279 * DP monitor, may need return false. 2280 */ 2281 if (hblanking < HBLANKING_MIN || (hfp < HP_MIN && hbp < HP_MIN)) { 2282 adj_hsync = SYNC_LEN_DEF; 2283 adj_hfp = HFP_HBP_DEF; 2284 adj_hbp = HFP_HBP_DEF; 2285 vref = adj->clock * 1000 / (adj->htotal * adj->vtotal); 2286 if (hblanking < HBLANKING_MIN) { 2287 delta_adj = HBLANKING_MIN - hblanking; 2288 adj_clock = vref * delta_adj * adj->vtotal; 2289 adj->clock += DIV_ROUND_UP(adj_clock, 1000); 2290 } else { 2291 delta_adj = hblanking - HBLANKING_MIN; 2292 adj_clock = vref * delta_adj * adj->vtotal; 2293 adj->clock -= DIV_ROUND_UP(adj_clock, 1000); 2294 } 2295 2296 DRM_WARN("illegal hblanking timing, use default.\n"); 2297 DRM_WARN("hfp(%d), hbp(%d), hsync(%d).\n", hfp, hbp, hsync); 2298 } else if (adj_hfp < HP_MIN) { 2299 /* Adjust hfp if hfp less than HP_MIN */ 2300 delta_adj = HP_MIN - adj_hfp; 2301 adj_hfp = HP_MIN; 2302 2303 /* 2304 * Balance total HBlanking pixel, if HBP does not have enough 2305 * space, adjust HSYNC length, otherwise adjust HBP 2306 */ 2307 if ((adj_hbp - delta_adj) < HP_MIN) 2308 /* HBP not enough space */ 2309 adj_hsync -= delta_adj; 2310 else 2311 adj_hbp -= delta_adj; 2312 } else if (adj_hbp < HP_MIN) { 2313 delta_adj = HP_MIN - adj_hbp; 2314 adj_hbp = HP_MIN; 2315 2316 /* 2317 * Balance total HBlanking pixel, if HBP hasn't enough space, 2318 * adjust HSYNC length, otherwize adjust HBP 2319 */ 2320 if ((adj_hfp - delta_adj) < HP_MIN) 2321 /* HFP not enough space */ 2322 adj_hsync -= delta_adj; 2323 else 2324 adj_hfp -= delta_adj; 2325 } 2326 2327 DRM_DEV_DEBUG_DRIVER(dev, "after mode fixup\n"); 2328 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2329 adj_hsync, adj_hfp, adj_hbp, adj->clock); 2330 2331 /* Reconstruct timing */ 2332 adj->hsync_start = adj->hdisplay + adj_hfp; 2333 adj->hsync_end = adj->hsync_start + adj_hsync; 2334 adj->htotal = adj->hsync_end + adj_hbp; 2335 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2336 adj->hsync_start, adj->hsync_end, adj->htotal); 2337 2338 return true; 2339 } 2340 2341 static int anx7625_bridge_atomic_check(struct drm_bridge *bridge, 2342 struct drm_bridge_state *bridge_state, 2343 struct drm_crtc_state *crtc_state, 2344 struct drm_connector_state *conn_state) 2345 { 2346 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2347 struct device *dev = &ctx->client->dev; 2348 2349 dev_dbg(dev, "drm bridge atomic check\n"); 2350 2351 anx7625_bridge_mode_fixup(bridge, &crtc_state->mode, 2352 &crtc_state->adjusted_mode); 2353 2354 return anx7625_connector_atomic_check(ctx, conn_state); 2355 } 2356 2357 static void anx7625_bridge_atomic_enable(struct drm_bridge *bridge, 2358 struct drm_bridge_state *state) 2359 { 2360 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2361 struct device *dev = &ctx->client->dev; 2362 struct drm_connector *connector; 2363 2364 dev_dbg(dev, "drm atomic enable\n"); 2365 2366 if (!bridge->encoder) { 2367 dev_err(dev, "Parent encoder object not found"); 2368 return; 2369 } 2370 2371 connector = drm_atomic_get_new_connector_for_encoder(state->base.state, 2372 bridge->encoder); 2373 if (!connector) 2374 return; 2375 2376 ctx->connector = connector; 2377 2378 pm_runtime_get_sync(dev); 2379 2380 anx7625_dp_start(ctx); 2381 } 2382 2383 static void anx7625_bridge_atomic_disable(struct drm_bridge *bridge, 2384 struct drm_bridge_state *old) 2385 { 2386 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2387 struct device *dev = &ctx->client->dev; 2388 2389 dev_dbg(dev, "drm atomic disable\n"); 2390 2391 ctx->connector = NULL; 2392 anx7625_dp_stop(ctx); 2393 2394 pm_runtime_put_sync(dev); 2395 } 2396 2397 static enum drm_connector_status 2398 anx7625_bridge_detect(struct drm_bridge *bridge) 2399 { 2400 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2401 struct device *dev = &ctx->client->dev; 2402 2403 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge detect\n"); 2404 2405 return anx7625_sink_detect(ctx); 2406 } 2407 2408 static struct edid *anx7625_bridge_get_edid(struct drm_bridge *bridge, 2409 struct drm_connector *connector) 2410 { 2411 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2412 struct device *dev = &ctx->client->dev; 2413 2414 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge get edid\n"); 2415 2416 return anx7625_get_edid(ctx); 2417 } 2418 2419 static const struct drm_bridge_funcs anx7625_bridge_funcs = { 2420 .attach = anx7625_bridge_attach, 2421 .detach = anx7625_bridge_detach, 2422 .mode_valid = anx7625_bridge_mode_valid, 2423 .mode_set = anx7625_bridge_mode_set, 2424 .atomic_check = anx7625_bridge_atomic_check, 2425 .atomic_enable = anx7625_bridge_atomic_enable, 2426 .atomic_disable = anx7625_bridge_atomic_disable, 2427 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 2428 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 2429 .atomic_reset = drm_atomic_helper_bridge_reset, 2430 .detect = anx7625_bridge_detect, 2431 .get_edid = anx7625_bridge_get_edid, 2432 }; 2433 2434 static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx, 2435 struct i2c_client *client) 2436 { 2437 int err = 0; 2438 2439 ctx->i2c.tx_p0_client = i2c_new_dummy_device(client->adapter, 2440 TX_P0_ADDR >> 1); 2441 if (IS_ERR(ctx->i2c.tx_p0_client)) 2442 return PTR_ERR(ctx->i2c.tx_p0_client); 2443 2444 ctx->i2c.tx_p1_client = i2c_new_dummy_device(client->adapter, 2445 TX_P1_ADDR >> 1); 2446 if (IS_ERR(ctx->i2c.tx_p1_client)) { 2447 err = PTR_ERR(ctx->i2c.tx_p1_client); 2448 goto free_tx_p0; 2449 } 2450 2451 ctx->i2c.tx_p2_client = i2c_new_dummy_device(client->adapter, 2452 TX_P2_ADDR >> 1); 2453 if (IS_ERR(ctx->i2c.tx_p2_client)) { 2454 err = PTR_ERR(ctx->i2c.tx_p2_client); 2455 goto free_tx_p1; 2456 } 2457 2458 ctx->i2c.rx_p0_client = i2c_new_dummy_device(client->adapter, 2459 RX_P0_ADDR >> 1); 2460 if (IS_ERR(ctx->i2c.rx_p0_client)) { 2461 err = PTR_ERR(ctx->i2c.rx_p0_client); 2462 goto free_tx_p2; 2463 } 2464 2465 ctx->i2c.rx_p1_client = i2c_new_dummy_device(client->adapter, 2466 RX_P1_ADDR >> 1); 2467 if (IS_ERR(ctx->i2c.rx_p1_client)) { 2468 err = PTR_ERR(ctx->i2c.rx_p1_client); 2469 goto free_rx_p0; 2470 } 2471 2472 ctx->i2c.rx_p2_client = i2c_new_dummy_device(client->adapter, 2473 RX_P2_ADDR >> 1); 2474 if (IS_ERR(ctx->i2c.rx_p2_client)) { 2475 err = PTR_ERR(ctx->i2c.rx_p2_client); 2476 goto free_rx_p1; 2477 } 2478 2479 ctx->i2c.tcpc_client = i2c_new_dummy_device(client->adapter, 2480 TCPC_INTERFACE_ADDR >> 1); 2481 if (IS_ERR(ctx->i2c.tcpc_client)) { 2482 err = PTR_ERR(ctx->i2c.tcpc_client); 2483 goto free_rx_p2; 2484 } 2485 2486 return 0; 2487 2488 free_rx_p2: 2489 i2c_unregister_device(ctx->i2c.rx_p2_client); 2490 free_rx_p1: 2491 i2c_unregister_device(ctx->i2c.rx_p1_client); 2492 free_rx_p0: 2493 i2c_unregister_device(ctx->i2c.rx_p0_client); 2494 free_tx_p2: 2495 i2c_unregister_device(ctx->i2c.tx_p2_client); 2496 free_tx_p1: 2497 i2c_unregister_device(ctx->i2c.tx_p1_client); 2498 free_tx_p0: 2499 i2c_unregister_device(ctx->i2c.tx_p0_client); 2500 2501 return err; 2502 } 2503 2504 static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx) 2505 { 2506 i2c_unregister_device(ctx->i2c.tx_p0_client); 2507 i2c_unregister_device(ctx->i2c.tx_p1_client); 2508 i2c_unregister_device(ctx->i2c.tx_p2_client); 2509 i2c_unregister_device(ctx->i2c.rx_p0_client); 2510 i2c_unregister_device(ctx->i2c.rx_p1_client); 2511 i2c_unregister_device(ctx->i2c.rx_p2_client); 2512 i2c_unregister_device(ctx->i2c.tcpc_client); 2513 } 2514 2515 static int __maybe_unused anx7625_runtime_pm_suspend(struct device *dev) 2516 { 2517 struct anx7625_data *ctx = dev_get_drvdata(dev); 2518 2519 mutex_lock(&ctx->lock); 2520 2521 anx7625_stop_dp_work(ctx); 2522 anx7625_power_standby(ctx); 2523 2524 mutex_unlock(&ctx->lock); 2525 2526 return 0; 2527 } 2528 2529 static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev) 2530 { 2531 struct anx7625_data *ctx = dev_get_drvdata(dev); 2532 2533 mutex_lock(&ctx->lock); 2534 2535 anx7625_power_on_init(ctx); 2536 anx7625_hpd_polling(ctx); 2537 2538 mutex_unlock(&ctx->lock); 2539 2540 return 0; 2541 } 2542 2543 static int __maybe_unused anx7625_resume(struct device *dev) 2544 { 2545 struct anx7625_data *ctx = dev_get_drvdata(dev); 2546 2547 if (!ctx->pdata.intp_irq) 2548 return 0; 2549 2550 if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev)) { 2551 enable_irq(ctx->pdata.intp_irq); 2552 anx7625_runtime_pm_resume(dev); 2553 } 2554 2555 return 0; 2556 } 2557 2558 static int __maybe_unused anx7625_suspend(struct device *dev) 2559 { 2560 struct anx7625_data *ctx = dev_get_drvdata(dev); 2561 2562 if (!ctx->pdata.intp_irq) 2563 return 0; 2564 2565 if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev)) { 2566 anx7625_runtime_pm_suspend(dev); 2567 disable_irq(ctx->pdata.intp_irq); 2568 } 2569 2570 return 0; 2571 } 2572 2573 static const struct dev_pm_ops anx7625_pm_ops = { 2574 SET_SYSTEM_SLEEP_PM_OPS(anx7625_suspend, anx7625_resume) 2575 SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, 2576 anx7625_runtime_pm_resume, NULL) 2577 }; 2578 2579 static void anx7625_runtime_disable(void *data) 2580 { 2581 pm_runtime_dont_use_autosuspend(data); 2582 pm_runtime_disable(data); 2583 } 2584 2585 static int anx7625_i2c_probe(struct i2c_client *client, 2586 const struct i2c_device_id *id) 2587 { 2588 struct anx7625_data *platform; 2589 struct anx7625_platform_data *pdata; 2590 int ret = 0; 2591 struct device *dev = &client->dev; 2592 2593 if (!i2c_check_functionality(client->adapter, 2594 I2C_FUNC_SMBUS_I2C_BLOCK)) { 2595 DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n"); 2596 return -ENODEV; 2597 } 2598 2599 platform = devm_kzalloc(dev, sizeof(*platform), GFP_KERNEL); 2600 if (!platform) { 2601 DRM_DEV_ERROR(dev, "fail to allocate driver data\n"); 2602 return -ENOMEM; 2603 } 2604 2605 pdata = &platform->pdata; 2606 2607 platform->client = client; 2608 i2c_set_clientdata(client, platform); 2609 2610 pdata->supplies[0].supply = "vdd10"; 2611 pdata->supplies[1].supply = "vdd18"; 2612 pdata->supplies[2].supply = "vdd33"; 2613 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies), 2614 pdata->supplies); 2615 if (ret) { 2616 DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret); 2617 return ret; 2618 } 2619 anx7625_init_gpio(platform); 2620 2621 mutex_init(&platform->lock); 2622 mutex_init(&platform->hdcp_wq_lock); 2623 2624 INIT_DELAYED_WORK(&platform->hdcp_work, hdcp_check_work_func); 2625 platform->hdcp_workqueue = create_workqueue("hdcp workqueue"); 2626 if (!platform->hdcp_workqueue) { 2627 dev_err(dev, "fail to create work queue\n"); 2628 ret = -ENOMEM; 2629 return ret; 2630 } 2631 2632 platform->pdata.intp_irq = client->irq; 2633 if (platform->pdata.intp_irq) { 2634 INIT_WORK(&platform->work, anx7625_work_func); 2635 platform->workqueue = alloc_workqueue("anx7625_work", 2636 WQ_FREEZABLE | WQ_MEM_RECLAIM, 1); 2637 if (!platform->workqueue) { 2638 DRM_DEV_ERROR(dev, "fail to create work queue\n"); 2639 ret = -ENOMEM; 2640 goto free_hdcp_wq; 2641 } 2642 2643 ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq, 2644 NULL, anx7625_intr_hpd_isr, 2645 IRQF_TRIGGER_FALLING | 2646 IRQF_ONESHOT, 2647 "anx7625-intp", platform); 2648 if (ret) { 2649 DRM_DEV_ERROR(dev, "fail to request irq\n"); 2650 goto free_wq; 2651 } 2652 } 2653 2654 platform->aux.name = "anx7625-aux"; 2655 platform->aux.dev = dev; 2656 platform->aux.transfer = anx7625_aux_transfer; 2657 drm_dp_aux_init(&platform->aux); 2658 devm_of_dp_aux_populate_ep_devices(&platform->aux); 2659 2660 ret = anx7625_parse_dt(dev, pdata); 2661 if (ret) { 2662 if (ret != -EPROBE_DEFER) 2663 DRM_DEV_ERROR(dev, "fail to parse DT : %d\n", ret); 2664 goto free_wq; 2665 } 2666 2667 if (anx7625_register_i2c_dummy_clients(platform, client) != 0) { 2668 ret = -ENOMEM; 2669 DRM_DEV_ERROR(dev, "fail to reserve I2C bus.\n"); 2670 goto free_wq; 2671 } 2672 2673 pm_runtime_enable(dev); 2674 pm_runtime_set_autosuspend_delay(dev, 1000); 2675 pm_runtime_use_autosuspend(dev); 2676 pm_suspend_ignore_children(dev, true); 2677 ret = devm_add_action_or_reset(dev, anx7625_runtime_disable, dev); 2678 if (ret) 2679 goto free_wq; 2680 2681 if (!platform->pdata.low_power_mode) { 2682 anx7625_disable_pd_protocol(platform); 2683 pm_runtime_get_sync(dev); 2684 } 2685 2686 /* Add work function */ 2687 if (platform->pdata.intp_irq) 2688 queue_work(platform->workqueue, &platform->work); 2689 2690 platform->bridge.funcs = &anx7625_bridge_funcs; 2691 platform->bridge.of_node = client->dev.of_node; 2692 if (!anx7625_of_panel_on_aux_bus(&client->dev)) 2693 platform->bridge.ops |= DRM_BRIDGE_OP_EDID; 2694 if (!platform->pdata.panel_bridge) 2695 platform->bridge.ops |= DRM_BRIDGE_OP_HPD | 2696 DRM_BRIDGE_OP_DETECT; 2697 platform->bridge.type = platform->pdata.panel_bridge ? 2698 DRM_MODE_CONNECTOR_eDP : 2699 DRM_MODE_CONNECTOR_DisplayPort; 2700 2701 drm_bridge_add(&platform->bridge); 2702 2703 if (!platform->pdata.is_dpi) { 2704 ret = anx7625_attach_dsi(platform); 2705 if (ret) { 2706 DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", ret); 2707 goto unregister_bridge; 2708 } 2709 } 2710 2711 if (platform->pdata.audio_en) 2712 anx7625_register_audio(dev, platform); 2713 2714 DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); 2715 2716 return 0; 2717 2718 unregister_bridge: 2719 drm_bridge_remove(&platform->bridge); 2720 2721 if (!platform->pdata.low_power_mode) 2722 pm_runtime_put_sync_suspend(&client->dev); 2723 2724 anx7625_unregister_i2c_dummy_clients(platform); 2725 2726 free_wq: 2727 if (platform->workqueue) 2728 destroy_workqueue(platform->workqueue); 2729 2730 free_hdcp_wq: 2731 if (platform->hdcp_workqueue) 2732 destroy_workqueue(platform->hdcp_workqueue); 2733 2734 return ret; 2735 } 2736 2737 static int anx7625_i2c_remove(struct i2c_client *client) 2738 { 2739 struct anx7625_data *platform = i2c_get_clientdata(client); 2740 2741 drm_bridge_remove(&platform->bridge); 2742 2743 if (platform->pdata.intp_irq) 2744 destroy_workqueue(platform->workqueue); 2745 2746 if (platform->hdcp_workqueue) { 2747 cancel_delayed_work(&platform->hdcp_work); 2748 flush_workqueue(platform->hdcp_workqueue); 2749 destroy_workqueue(platform->hdcp_workqueue); 2750 } 2751 2752 if (!platform->pdata.low_power_mode) 2753 pm_runtime_put_sync_suspend(&client->dev); 2754 2755 anx7625_unregister_i2c_dummy_clients(platform); 2756 2757 if (platform->pdata.audio_en) 2758 anx7625_unregister_audio(platform); 2759 2760 return 0; 2761 } 2762 2763 static const struct i2c_device_id anx7625_id[] = { 2764 {"anx7625", 0}, 2765 {} 2766 }; 2767 2768 MODULE_DEVICE_TABLE(i2c, anx7625_id); 2769 2770 static const struct of_device_id anx_match_table[] = { 2771 {.compatible = "analogix,anx7625",}, 2772 {}, 2773 }; 2774 MODULE_DEVICE_TABLE(of, anx_match_table); 2775 2776 static struct i2c_driver anx7625_driver = { 2777 .driver = { 2778 .name = "anx7625", 2779 .of_match_table = anx_match_table, 2780 .pm = &anx7625_pm_ops, 2781 }, 2782 .probe = anx7625_i2c_probe, 2783 .remove = anx7625_i2c_remove, 2784 2785 .id_table = anx7625_id, 2786 }; 2787 2788 module_i2c_driver(anx7625_driver); 2789 2790 MODULE_DESCRIPTION("MIPI2DP anx7625 driver"); 2791 MODULE_AUTHOR("Xin Ji <xji@analogixsemi.com>"); 2792 MODULE_LICENSE("GPL v2"); 2793 MODULE_VERSION(ANX7625_DRV_VERSION); 2794