1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright(c) 2020, Analogix Semiconductor. All rights reserved. 4 * 5 */ 6 #include <linux/gcd.h> 7 #include <linux/gpio/consumer.h> 8 #include <linux/i2c.h> 9 #include <linux/interrupt.h> 10 #include <linux/iopoll.h> 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/mutex.h> 14 #include <linux/pm_runtime.h> 15 #include <linux/regulator/consumer.h> 16 #include <linux/slab.h> 17 #include <linux/types.h> 18 #include <linux/workqueue.h> 19 20 #include <linux/of_gpio.h> 21 #include <linux/of_graph.h> 22 #include <linux/of_platform.h> 23 24 #include <drm/display/drm_dp_aux_bus.h> 25 #include <drm/display/drm_dp_helper.h> 26 #include <drm/display/drm_hdcp_helper.h> 27 #include <drm/drm_atomic_helper.h> 28 #include <drm/drm_bridge.h> 29 #include <drm/drm_crtc_helper.h> 30 #include <drm/drm_edid.h> 31 #include <drm/drm_mipi_dsi.h> 32 #include <drm/drm_of.h> 33 #include <drm/drm_panel.h> 34 #include <drm/drm_print.h> 35 #include <drm/drm_probe_helper.h> 36 37 #include <media/v4l2-fwnode.h> 38 #include <sound/hdmi-codec.h> 39 #include <video/display_timing.h> 40 41 #include "anx7625.h" 42 43 /* 44 * There is a sync issue while access I2C register between AP(CPU) and 45 * internal firmware(OCM), to avoid the race condition, AP should access 46 * the reserved slave address before slave address occurs changes. 47 */ 48 static int i2c_access_workaround(struct anx7625_data *ctx, 49 struct i2c_client *client) 50 { 51 u8 offset; 52 struct device *dev = &client->dev; 53 int ret; 54 55 if (client == ctx->last_client) 56 return 0; 57 58 ctx->last_client = client; 59 60 if (client == ctx->i2c.tcpc_client) 61 offset = RSVD_00_ADDR; 62 else if (client == ctx->i2c.tx_p0_client) 63 offset = RSVD_D1_ADDR; 64 else if (client == ctx->i2c.tx_p1_client) 65 offset = RSVD_60_ADDR; 66 else if (client == ctx->i2c.rx_p0_client) 67 offset = RSVD_39_ADDR; 68 else if (client == ctx->i2c.rx_p1_client) 69 offset = RSVD_7F_ADDR; 70 else 71 offset = RSVD_00_ADDR; 72 73 ret = i2c_smbus_write_byte_data(client, offset, 0x00); 74 if (ret < 0) 75 DRM_DEV_ERROR(dev, 76 "fail to access i2c id=%x\n:%x", 77 client->addr, offset); 78 79 return ret; 80 } 81 82 static int anx7625_reg_read(struct anx7625_data *ctx, 83 struct i2c_client *client, u8 reg_addr) 84 { 85 int ret; 86 struct device *dev = &client->dev; 87 88 i2c_access_workaround(ctx, client); 89 90 ret = i2c_smbus_read_byte_data(client, reg_addr); 91 if (ret < 0) 92 DRM_DEV_ERROR(dev, "read i2c fail id=%x:%x\n", 93 client->addr, reg_addr); 94 95 return ret; 96 } 97 98 static int anx7625_reg_block_read(struct anx7625_data *ctx, 99 struct i2c_client *client, 100 u8 reg_addr, u8 len, u8 *buf) 101 { 102 int ret; 103 struct device *dev = &client->dev; 104 105 i2c_access_workaround(ctx, client); 106 107 ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf); 108 if (ret < 0) 109 DRM_DEV_ERROR(dev, "read i2c block fail id=%x:%x\n", 110 client->addr, reg_addr); 111 112 return ret; 113 } 114 115 static int anx7625_reg_write(struct anx7625_data *ctx, 116 struct i2c_client *client, 117 u8 reg_addr, u8 reg_val) 118 { 119 int ret; 120 struct device *dev = &client->dev; 121 122 i2c_access_workaround(ctx, client); 123 124 ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val); 125 126 if (ret < 0) 127 DRM_DEV_ERROR(dev, "fail to write i2c id=%x\n:%x", 128 client->addr, reg_addr); 129 130 return ret; 131 } 132 133 static int anx7625_reg_block_write(struct anx7625_data *ctx, 134 struct i2c_client *client, 135 u8 reg_addr, u8 len, u8 *buf) 136 { 137 int ret; 138 struct device *dev = &client->dev; 139 140 i2c_access_workaround(ctx, client); 141 142 ret = i2c_smbus_write_i2c_block_data(client, reg_addr, len, buf); 143 if (ret < 0) 144 dev_err(dev, "write i2c block failed id=%x\n:%x", 145 client->addr, reg_addr); 146 147 return ret; 148 } 149 150 static int anx7625_write_or(struct anx7625_data *ctx, 151 struct i2c_client *client, 152 u8 offset, u8 mask) 153 { 154 int val; 155 156 val = anx7625_reg_read(ctx, client, offset); 157 if (val < 0) 158 return val; 159 160 return anx7625_reg_write(ctx, client, offset, (val | (mask))); 161 } 162 163 static int anx7625_write_and(struct anx7625_data *ctx, 164 struct i2c_client *client, 165 u8 offset, u8 mask) 166 { 167 int val; 168 169 val = anx7625_reg_read(ctx, client, offset); 170 if (val < 0) 171 return val; 172 173 return anx7625_reg_write(ctx, client, offset, (val & (mask))); 174 } 175 176 static int anx7625_write_and_or(struct anx7625_data *ctx, 177 struct i2c_client *client, 178 u8 offset, u8 and_mask, u8 or_mask) 179 { 180 int val; 181 182 val = anx7625_reg_read(ctx, client, offset); 183 if (val < 0) 184 return val; 185 186 return anx7625_reg_write(ctx, client, 187 offset, (val & and_mask) | (or_mask)); 188 } 189 190 static int anx7625_config_bit_matrix(struct anx7625_data *ctx) 191 { 192 int i, ret; 193 194 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 195 AUDIO_CONTROL_REGISTER, 0x80); 196 for (i = 0; i < 13; i++) 197 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 198 VIDEO_BIT_MATRIX_12 + i, 199 0x18 + i); 200 201 return ret; 202 } 203 204 static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) 205 { 206 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS); 207 } 208 209 static int wait_aux_op_finish(struct anx7625_data *ctx) 210 { 211 struct device *dev = &ctx->client->dev; 212 int val; 213 int ret; 214 215 ret = readx_poll_timeout(anx7625_read_ctrl_status_p0, 216 ctx, val, 217 (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)), 218 2000, 219 2000 * 150); 220 if (ret) { 221 DRM_DEV_ERROR(dev, "aux operation fail!\n"); 222 return -EIO; 223 } 224 225 val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 226 AP_AUX_CTRL_STATUS); 227 if (val < 0 || (val & 0x0F)) { 228 DRM_DEV_ERROR(dev, "aux status %02x\n", val); 229 return -EIO; 230 } 231 232 return 0; 233 } 234 235 static int anx7625_aux_trans(struct anx7625_data *ctx, u8 op, u32 address, 236 u8 len, u8 *buf) 237 { 238 struct device *dev = &ctx->client->dev; 239 int ret; 240 u8 addrh, addrm, addrl; 241 u8 cmd; 242 bool is_write = !(op & DP_AUX_I2C_READ); 243 244 if (len > DP_AUX_MAX_PAYLOAD_BYTES) { 245 dev_err(dev, "exceed aux buffer len.\n"); 246 return -EINVAL; 247 } 248 249 if (!len) 250 return len; 251 252 addrl = address & 0xFF; 253 addrm = (address >> 8) & 0xFF; 254 addrh = (address >> 16) & 0xFF; 255 256 if (!is_write) 257 op &= ~DP_AUX_I2C_MOT; 258 cmd = DPCD_CMD(len, op); 259 260 /* Set command and length */ 261 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 262 AP_AUX_COMMAND, cmd); 263 264 /* Set aux access address */ 265 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 266 AP_AUX_ADDR_7_0, addrl); 267 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 268 AP_AUX_ADDR_15_8, addrm); 269 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 270 AP_AUX_ADDR_19_16, addrh); 271 272 if (is_write) 273 ret |= anx7625_reg_block_write(ctx, ctx->i2c.rx_p0_client, 274 AP_AUX_BUFF_START, len, buf); 275 /* Enable aux access */ 276 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 277 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 278 279 if (ret < 0) { 280 dev_err(dev, "cannot access aux related register.\n"); 281 return -EIO; 282 } 283 284 ret = wait_aux_op_finish(ctx); 285 if (ret < 0) { 286 dev_err(dev, "aux IO error: wait aux op finish.\n"); 287 return ret; 288 } 289 290 /* Write done */ 291 if (is_write) 292 return len; 293 294 /* Read done, read out dpcd data */ 295 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 296 AP_AUX_BUFF_START, len, buf); 297 if (ret < 0) { 298 dev_err(dev, "read dpcd register failed\n"); 299 return -EIO; 300 } 301 302 return len; 303 } 304 305 static int anx7625_video_mute_control(struct anx7625_data *ctx, 306 u8 status) 307 { 308 int ret; 309 310 if (status) { 311 /* Set mute on flag */ 312 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 313 AP_AV_STATUS, AP_MIPI_MUTE); 314 /* Clear mipi RX en */ 315 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 316 AP_AV_STATUS, (u8)~AP_MIPI_RX_EN); 317 } else { 318 /* Mute off flag */ 319 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 320 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 321 /* Set MIPI RX EN */ 322 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 323 AP_AV_STATUS, AP_MIPI_RX_EN); 324 } 325 326 return ret; 327 } 328 329 /* Reduction of fraction a/b */ 330 static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) 331 { 332 unsigned long gcd_num; 333 unsigned long tmp_a, tmp_b; 334 u32 i = 1; 335 336 gcd_num = gcd(*a, *b); 337 *a /= gcd_num; 338 *b /= gcd_num; 339 340 tmp_a = *a; 341 tmp_b = *b; 342 343 while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) { 344 i++; 345 *a = tmp_a / i; 346 *b = tmp_b / i; 347 } 348 349 /* 350 * In the end, make a, b larger to have higher ODFC PLL 351 * output frequency accuracy 352 */ 353 while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) { 354 *a <<= 1; 355 *b <<= 1; 356 } 357 358 *a >>= 1; 359 *b >>= 1; 360 } 361 362 static int anx7625_calculate_m_n(u32 pixelclock, 363 unsigned long *m, 364 unsigned long *n, 365 u8 *post_divider) 366 { 367 if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) { 368 /* Pixel clock frequency is too high */ 369 DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n", 370 pixelclock, 371 PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN); 372 return -EINVAL; 373 } 374 375 if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) { 376 /* Pixel clock frequency is too low */ 377 DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n", 378 pixelclock, 379 PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX); 380 return -EINVAL; 381 } 382 383 for (*post_divider = 1; 384 pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));) 385 *post_divider += 1; 386 387 if (*post_divider > POST_DIVIDER_MAX) { 388 for (*post_divider = 1; 389 (pixelclock < 390 (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));) 391 *post_divider += 1; 392 393 if (*post_divider > POST_DIVIDER_MAX) { 394 DRM_ERROR("cannot find property post_divider(%d)\n", 395 *post_divider); 396 return -EDOM; 397 } 398 } 399 400 /* Patch to improve the accuracy */ 401 if (*post_divider == 7) { 402 /* 27,000,000 is not divisible by 7 */ 403 *post_divider = 8; 404 } else if (*post_divider == 11) { 405 /* 27,000,000 is not divisible by 11 */ 406 *post_divider = 12; 407 } else if ((*post_divider == 13) || (*post_divider == 14)) { 408 /* 27,000,000 is not divisible by 13 or 14 */ 409 *post_divider = 15; 410 } 411 412 if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) { 413 DRM_ERROR("act clock(%u) large than maximum(%lu)\n", 414 pixelclock * (*post_divider), 415 PLL_OUT_FREQ_ABS_MAX); 416 return -EDOM; 417 } 418 419 *m = pixelclock; 420 *n = XTAL_FRQ / (*post_divider); 421 422 anx7625_reduction_of_a_fraction(m, n); 423 424 return 0; 425 } 426 427 static int anx7625_odfc_config(struct anx7625_data *ctx, 428 u8 post_divider) 429 { 430 int ret; 431 struct device *dev = &ctx->client->dev; 432 433 /* Config input reference clock frequency 27MHz/19.2MHz */ 434 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 435 ~(REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 436 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 437 (REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 438 /* Post divider */ 439 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 440 MIPI_DIGITAL_PLL_8, 0x0f); 441 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8, 442 post_divider << 4); 443 444 /* Add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */ 445 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 446 ~MIPI_PLL_VCO_TUNE_REG_VAL); 447 448 /* Reset ODFC PLL */ 449 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 450 ~MIPI_PLL_RESET_N); 451 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 452 MIPI_PLL_RESET_N); 453 454 if (ret < 0) 455 DRM_DEV_ERROR(dev, "IO error.\n"); 456 457 return ret; 458 } 459 460 /* 461 * The MIPI source video data exist large variation (e.g. 59Hz ~ 61Hz), 462 * anx7625 defined K ratio for matching MIPI input video clock and 463 * DP output video clock. Increase K value can match bigger video data 464 * variation. IVO panel has small variation than DP CTS spec, need 465 * decrease the K value. 466 */ 467 static int anx7625_set_k_value(struct anx7625_data *ctx) 468 { 469 struct edid *edid = (struct edid *)ctx->slimport_edid_p.edid_raw_data; 470 471 if (edid->mfg_id[0] == IVO_MID0 && edid->mfg_id[1] == IVO_MID1) 472 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 473 MIPI_DIGITAL_ADJ_1, 0x3B); 474 475 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 476 MIPI_DIGITAL_ADJ_1, 0x3D); 477 } 478 479 static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) 480 { 481 struct device *dev = &ctx->client->dev; 482 unsigned long m, n; 483 u16 htotal; 484 int ret; 485 u8 post_divider = 0; 486 487 ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000, 488 &m, &n, &post_divider); 489 490 if (ret) { 491 DRM_DEV_ERROR(dev, "cannot get property m n value.\n"); 492 return ret; 493 } 494 495 DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n", 496 m, n, post_divider); 497 498 /* Configure pixel clock */ 499 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L, 500 (ctx->dt.pixelclock.min / 1000) & 0xFF); 501 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H, 502 (ctx->dt.pixelclock.min / 1000) >> 8); 503 /* Lane count */ 504 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 505 MIPI_LANE_CTRL_0, 0xfc); 506 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 507 MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); 508 509 /* Htotal */ 510 htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + 511 ctx->dt.hback_porch.min + ctx->dt.hsync_len.min; 512 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 513 HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF); 514 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 515 HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8); 516 /* Hactive */ 517 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 518 HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF); 519 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 520 HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8); 521 /* HFP */ 522 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 523 HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min); 524 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 525 HORIZONTAL_FRONT_PORCH_H, 526 ctx->dt.hfront_porch.min >> 8); 527 /* HWS */ 528 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 529 HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min); 530 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 531 HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8); 532 /* HBP */ 533 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 534 HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min); 535 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 536 HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8); 537 /* Vactive */ 538 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L, 539 ctx->dt.vactive.min); 540 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H, 541 ctx->dt.vactive.min >> 8); 542 /* VFP */ 543 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 544 VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min); 545 /* VWS */ 546 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 547 VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min); 548 /* VBP */ 549 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 550 VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min); 551 /* M value */ 552 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 553 MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff); 554 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 555 MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff); 556 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 557 MIPI_PLL_M_NUM_7_0, (m & 0xff)); 558 /* N value */ 559 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 560 MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff); 561 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 562 MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff); 563 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0, 564 (n & 0xff)); 565 566 anx7625_set_k_value(ctx); 567 568 ret |= anx7625_odfc_config(ctx, post_divider - 1); 569 570 if (ret < 0) 571 DRM_DEV_ERROR(dev, "mipi dsi setup IO error.\n"); 572 573 return ret; 574 } 575 576 static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx) 577 { 578 int val; 579 struct device *dev = &ctx->client->dev; 580 581 /* Swap MIPI-DSI data lane 3 P and N */ 582 val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP); 583 if (val < 0) { 584 DRM_DEV_ERROR(dev, "IO error : access MIPI_SWAP.\n"); 585 return -EIO; 586 } 587 588 val |= (1 << MIPI_SWAP_CH3); 589 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val); 590 } 591 592 static int anx7625_api_dsi_config(struct anx7625_data *ctx) 593 594 { 595 int val, ret; 596 struct device *dev = &ctx->client->dev; 597 598 /* Swap MIPI-DSI data lane 3 P and N */ 599 ret = anx7625_swap_dsi_lane3(ctx); 600 if (ret < 0) { 601 DRM_DEV_ERROR(dev, "IO error : swap dsi lane 3 fail.\n"); 602 return ret; 603 } 604 605 /* DSI clock settings */ 606 val = (0 << MIPI_HS_PWD_CLK) | 607 (0 << MIPI_HS_RT_CLK) | 608 (0 << MIPI_PD_CLK) | 609 (1 << MIPI_CLK_RT_MANUAL_PD_EN) | 610 (1 << MIPI_CLK_HS_MANUAL_PD_EN) | 611 (0 << MIPI_CLK_DET_DET_BYPASS) | 612 (0 << MIPI_CLK_MISS_CTRL) | 613 (0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN); 614 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 615 MIPI_PHY_CONTROL_3, val); 616 617 /* 618 * Decreased HS prepare timing delay from 160ns to 80ns work with 619 * a) Dragon board 810 series (Qualcomm AP) 620 * b) Moving Pixel DSI source (PG3A pattern generator + 621 * P332 D-PHY Probe) default D-PHY timing 622 * 5ns/step 623 */ 624 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 625 MIPI_TIME_HS_PRPR, 0x10); 626 627 /* Enable DSI mode*/ 628 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18, 629 SELECT_DSI << MIPI_DPI_SELECT); 630 631 ret |= anx7625_dsi_video_timing_config(ctx); 632 if (ret < 0) { 633 DRM_DEV_ERROR(dev, "dsi video timing config fail\n"); 634 return ret; 635 } 636 637 /* Toggle m, n ready */ 638 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 639 ~(MIPI_M_NUM_READY | MIPI_N_NUM_READY)); 640 usleep_range(1000, 1100); 641 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 642 MIPI_M_NUM_READY | MIPI_N_NUM_READY); 643 644 /* Configure integer stable register */ 645 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 646 MIPI_VIDEO_STABLE_CNT, 0x02); 647 /* Power on MIPI RX */ 648 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 649 MIPI_LANE_CTRL_10, 0x00); 650 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 651 MIPI_LANE_CTRL_10, 0x80); 652 653 if (ret < 0) 654 DRM_DEV_ERROR(dev, "IO error : mipi dsi enable init fail.\n"); 655 656 return ret; 657 } 658 659 static int anx7625_dsi_config(struct anx7625_data *ctx) 660 { 661 struct device *dev = &ctx->client->dev; 662 int ret; 663 664 DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n"); 665 666 /* DSC disable */ 667 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 668 R_DSC_CTRL_0, ~DSC_EN); 669 670 ret |= anx7625_api_dsi_config(ctx); 671 672 if (ret < 0) { 673 DRM_DEV_ERROR(dev, "IO error : api dsi config error.\n"); 674 return ret; 675 } 676 677 /* Set MIPI RX EN */ 678 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 679 AP_AV_STATUS, AP_MIPI_RX_EN); 680 /* Clear mute flag */ 681 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 682 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 683 if (ret < 0) 684 DRM_DEV_ERROR(dev, "IO error : enable mipi rx fail.\n"); 685 else 686 DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n"); 687 688 return ret; 689 } 690 691 static int anx7625_api_dpi_config(struct anx7625_data *ctx) 692 { 693 struct device *dev = &ctx->client->dev; 694 u16 freq = ctx->dt.pixelclock.min / 1000; 695 int ret; 696 697 /* configure pixel clock */ 698 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 699 PIXEL_CLOCK_L, freq & 0xFF); 700 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 701 PIXEL_CLOCK_H, (freq >> 8)); 702 703 /* set DPI mode */ 704 /* set to DPI PLL module sel */ 705 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 706 MIPI_DIGITAL_PLL_9, 0x20); 707 /* power down MIPI */ 708 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 709 MIPI_LANE_CTRL_10, 0x08); 710 /* enable DPI mode */ 711 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 712 MIPI_DIGITAL_PLL_18, 0x1C); 713 /* set first edge */ 714 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 715 VIDEO_CONTROL_0, 0x06); 716 if (ret < 0) 717 DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); 718 719 return ret; 720 } 721 722 static int anx7625_dpi_config(struct anx7625_data *ctx) 723 { 724 struct device *dev = &ctx->client->dev; 725 int ret; 726 727 DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); 728 729 /* DSC disable */ 730 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 731 R_DSC_CTRL_0, ~DSC_EN); 732 if (ret < 0) { 733 DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); 734 return ret; 735 } 736 737 ret = anx7625_config_bit_matrix(ctx); 738 if (ret < 0) { 739 DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); 740 return ret; 741 } 742 743 ret = anx7625_api_dpi_config(ctx); 744 if (ret < 0) { 745 DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); 746 return ret; 747 } 748 749 /* set MIPI RX EN */ 750 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 751 AP_AV_STATUS, AP_MIPI_RX_EN); 752 /* clear mute flag */ 753 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 754 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 755 if (ret < 0) 756 DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); 757 758 return ret; 759 } 760 761 static int anx7625_read_flash_status(struct anx7625_data *ctx) 762 { 763 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, R_RAM_CTRL); 764 } 765 766 static int anx7625_hdcp_key_probe(struct anx7625_data *ctx) 767 { 768 int ret, val; 769 struct device *dev = &ctx->client->dev; 770 u8 ident[FLASH_BUF_LEN]; 771 772 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 773 FLASH_ADDR_HIGH, 0x91); 774 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 775 FLASH_ADDR_LOW, 0xA0); 776 if (ret < 0) { 777 dev_err(dev, "IO error : set key flash address.\n"); 778 return ret; 779 } 780 781 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 782 FLASH_LEN_HIGH, (FLASH_BUF_LEN - 1) >> 8); 783 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 784 FLASH_LEN_LOW, (FLASH_BUF_LEN - 1) & 0xFF); 785 if (ret < 0) { 786 dev_err(dev, "IO error : set key flash len.\n"); 787 return ret; 788 } 789 790 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 791 R_FLASH_RW_CTRL, FLASH_READ); 792 ret |= readx_poll_timeout(anx7625_read_flash_status, 793 ctx, val, 794 ((val & FLASH_DONE) || (val < 0)), 795 2000, 796 2000 * 150); 797 if (ret) { 798 dev_err(dev, "flash read access fail!\n"); 799 return -EIO; 800 } 801 802 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 803 FLASH_BUF_BASE_ADDR, 804 FLASH_BUF_LEN, ident); 805 if (ret < 0) { 806 dev_err(dev, "read flash data fail!\n"); 807 return -EIO; 808 } 809 810 if (ident[29] == 0xFF && ident[30] == 0xFF && ident[31] == 0xFF) 811 return -EINVAL; 812 813 return 0; 814 } 815 816 static int anx7625_hdcp_key_load(struct anx7625_data *ctx) 817 { 818 int ret; 819 struct device *dev = &ctx->client->dev; 820 821 /* Select HDCP 1.4 KEY */ 822 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 823 R_BOOT_RETRY, 0x12); 824 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 825 FLASH_ADDR_HIGH, HDCP14KEY_START_ADDR >> 8); 826 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 827 FLASH_ADDR_LOW, HDCP14KEY_START_ADDR & 0xFF); 828 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 829 R_RAM_LEN_H, HDCP14KEY_SIZE >> 12); 830 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 831 R_RAM_LEN_L, HDCP14KEY_SIZE >> 4); 832 833 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 834 R_RAM_ADDR_H, 0); 835 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 836 R_RAM_ADDR_L, 0); 837 /* Enable HDCP 1.4 KEY load */ 838 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 839 R_RAM_CTRL, DECRYPT_EN | LOAD_START); 840 dev_dbg(dev, "load HDCP 1.4 key done\n"); 841 return ret; 842 } 843 844 static int anx7625_hdcp_disable(struct anx7625_data *ctx) 845 { 846 int ret; 847 struct device *dev = &ctx->client->dev; 848 849 dev_dbg(dev, "disable HDCP 1.4\n"); 850 851 /* Disable HDCP */ 852 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 853 /* Try auth flag */ 854 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 855 /* Interrupt for DRM */ 856 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 857 if (ret < 0) 858 dev_err(dev, "fail to disable HDCP\n"); 859 860 return anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 861 TX_HDCP_CTRL0, ~HARD_AUTH_EN & 0xFF); 862 } 863 864 static int anx7625_hdcp_enable(struct anx7625_data *ctx) 865 { 866 u8 bcap; 867 int ret; 868 struct device *dev = &ctx->client->dev; 869 870 ret = anx7625_hdcp_key_probe(ctx); 871 if (ret) { 872 dev_dbg(dev, "no key found, not to do hdcp\n"); 873 return ret; 874 } 875 876 /* Read downstream capability */ 877 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_READ, 0x68028, 1, &bcap); 878 if (ret < 0) 879 return ret; 880 881 if (!(bcap & 0x01)) { 882 pr_warn("downstream not support HDCP 1.4, cap(%x).\n", bcap); 883 return 0; 884 } 885 886 dev_dbg(dev, "enable HDCP 1.4\n"); 887 888 /* First clear HDCP state */ 889 ret = anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 890 TX_HDCP_CTRL0, 891 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 892 usleep_range(1000, 1100); 893 /* Second clear HDCP state */ 894 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 895 TX_HDCP_CTRL0, 896 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 897 898 /* Set time for waiting KSVR */ 899 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 900 SP_TX_WAIT_KSVR_TIME, 0xc8); 901 /* Set time for waiting R0 */ 902 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 903 SP_TX_WAIT_R0_TIME, 0xb0); 904 ret |= anx7625_hdcp_key_load(ctx); 905 if (ret) { 906 pr_warn("prepare HDCP key failed.\n"); 907 return ret; 908 } 909 910 ret = anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20); 911 912 /* Try auth flag */ 913 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 914 /* Interrupt for DRM */ 915 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 916 if (ret < 0) 917 dev_err(dev, "fail to enable HDCP\n"); 918 919 return anx7625_write_or(ctx, ctx->i2c.tx_p0_client, 920 TX_HDCP_CTRL0, HARD_AUTH_EN); 921 } 922 923 static void anx7625_dp_start(struct anx7625_data *ctx) 924 { 925 int ret; 926 struct device *dev = &ctx->client->dev; 927 u8 data; 928 929 if (!ctx->display_timing_valid) { 930 DRM_DEV_ERROR(dev, "mipi not set display timing yet.\n"); 931 return; 932 } 933 934 dev_dbg(dev, "set downstream sink into normal\n"); 935 /* Downstream sink enter into normal mode */ 936 data = 1; 937 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, 0x000600, 1, &data); 938 if (ret < 0) 939 dev_err(dev, "IO error : set sink into normal mode fail\n"); 940 941 /* Disable HDCP */ 942 anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 943 944 if (ctx->pdata.is_dpi) 945 ret = anx7625_dpi_config(ctx); 946 else 947 ret = anx7625_dsi_config(ctx); 948 949 if (ret < 0) 950 DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); 951 952 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 953 954 ctx->dp_en = 1; 955 } 956 957 static void anx7625_dp_stop(struct anx7625_data *ctx) 958 { 959 struct device *dev = &ctx->client->dev; 960 int ret; 961 u8 data; 962 963 DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n"); 964 965 /* 966 * Video disable: 0x72:08 bit 7 = 0; 967 * Audio disable: 0x70:87 bit 0 = 0; 968 */ 969 ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe); 970 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f); 971 972 ret |= anx7625_video_mute_control(ctx, 1); 973 974 dev_dbg(dev, "notify downstream enter into standby\n"); 975 /* Downstream monitor enter into standby mode */ 976 data = 2; 977 ret |= anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, 0x000600, 1, &data); 978 if (ret < 0) 979 DRM_DEV_ERROR(dev, "IO error : mute video fail\n"); 980 981 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 982 983 ctx->dp_en = 0; 984 } 985 986 static int sp_tx_rst_aux(struct anx7625_data *ctx) 987 { 988 int ret; 989 990 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 991 AUX_RST); 992 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 993 ~AUX_RST); 994 return ret; 995 } 996 997 static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset) 998 { 999 int ret; 1000 1001 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1002 AP_AUX_BUFF_START, offset); 1003 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1004 AP_AUX_COMMAND, 0x04); 1005 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1006 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1007 return (ret | wait_aux_op_finish(ctx)); 1008 } 1009 1010 static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd) 1011 { 1012 int ret; 1013 1014 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1015 AP_AUX_COMMAND, len_cmd); 1016 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1017 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1018 return (ret | wait_aux_op_finish(ctx)); 1019 } 1020 1021 static int sp_tx_get_edid_block(struct anx7625_data *ctx) 1022 { 1023 int c = 0; 1024 struct device *dev = &ctx->client->dev; 1025 1026 sp_tx_aux_wr(ctx, 0x7e); 1027 sp_tx_aux_rd(ctx, 0x01); 1028 c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START); 1029 if (c < 0) { 1030 DRM_DEV_ERROR(dev, "IO error : access AUX BUFF.\n"); 1031 return -EIO; 1032 } 1033 1034 DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1); 1035 1036 if (c > MAX_EDID_BLOCK) 1037 c = 1; 1038 1039 return c; 1040 } 1041 1042 static int edid_read(struct anx7625_data *ctx, 1043 u8 offset, u8 *pblock_buf) 1044 { 1045 int ret, cnt; 1046 struct device *dev = &ctx->client->dev; 1047 1048 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1049 sp_tx_aux_wr(ctx, offset); 1050 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1051 ret = sp_tx_aux_rd(ctx, 0xf1); 1052 1053 if (ret) { 1054 ret = sp_tx_rst_aux(ctx); 1055 DRM_DEV_DEBUG_DRIVER(dev, "edid read fail, reset!\n"); 1056 } else { 1057 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1058 AP_AUX_BUFF_START, 1059 MAX_DPCD_BUFFER_SIZE, 1060 pblock_buf); 1061 if (ret > 0) 1062 break; 1063 } 1064 } 1065 1066 if (cnt > EDID_TRY_CNT) 1067 return -EIO; 1068 1069 return ret; 1070 } 1071 1072 static int segments_edid_read(struct anx7625_data *ctx, 1073 u8 segment, u8 *buf, u8 offset) 1074 { 1075 u8 cnt; 1076 int ret; 1077 struct device *dev = &ctx->client->dev; 1078 1079 /* Write address only */ 1080 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1081 AP_AUX_ADDR_7_0, 0x30); 1082 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1083 AP_AUX_COMMAND, 0x04); 1084 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1085 AP_AUX_CTRL_STATUS, 1086 AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN); 1087 1088 ret |= wait_aux_op_finish(ctx); 1089 /* Write segment address */ 1090 ret |= sp_tx_aux_wr(ctx, segment); 1091 /* Data read */ 1092 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1093 AP_AUX_ADDR_7_0, 0x50); 1094 if (ret) { 1095 DRM_DEV_ERROR(dev, "IO error : aux initial fail.\n"); 1096 return ret; 1097 } 1098 1099 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1100 sp_tx_aux_wr(ctx, offset); 1101 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1102 ret = sp_tx_aux_rd(ctx, 0xf1); 1103 1104 if (ret) { 1105 ret = sp_tx_rst_aux(ctx); 1106 DRM_DEV_ERROR(dev, "segment read fail, reset!\n"); 1107 } else { 1108 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1109 AP_AUX_BUFF_START, 1110 MAX_DPCD_BUFFER_SIZE, buf); 1111 if (ret > 0) 1112 break; 1113 } 1114 } 1115 1116 if (cnt > EDID_TRY_CNT) 1117 return -EIO; 1118 1119 return ret; 1120 } 1121 1122 static int sp_tx_edid_read(struct anx7625_data *ctx, 1123 u8 *pedid_blocks_buf) 1124 { 1125 u8 offset; 1126 int edid_pos; 1127 int count, blocks_num; 1128 u8 pblock_buf[MAX_DPCD_BUFFER_SIZE]; 1129 u8 i, j; 1130 int g_edid_break = 0; 1131 int ret; 1132 struct device *dev = &ctx->client->dev; 1133 1134 /* Address initial */ 1135 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1136 AP_AUX_ADDR_7_0, 0x50); 1137 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1138 AP_AUX_ADDR_15_8, 0); 1139 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 1140 AP_AUX_ADDR_19_16, 0xf0); 1141 if (ret < 0) { 1142 DRM_DEV_ERROR(dev, "access aux channel IO error.\n"); 1143 return -EIO; 1144 } 1145 1146 blocks_num = sp_tx_get_edid_block(ctx); 1147 if (blocks_num < 0) 1148 return blocks_num; 1149 1150 count = 0; 1151 1152 do { 1153 switch (count) { 1154 case 0: 1155 case 1: 1156 for (i = 0; i < 8; i++) { 1157 offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE; 1158 g_edid_break = edid_read(ctx, offset, 1159 pblock_buf); 1160 1161 if (g_edid_break < 0) 1162 break; 1163 1164 memcpy(&pedid_blocks_buf[offset], 1165 pblock_buf, 1166 MAX_DPCD_BUFFER_SIZE); 1167 } 1168 1169 break; 1170 case 2: 1171 offset = 0x00; 1172 1173 for (j = 0; j < 8; j++) { 1174 edid_pos = (j + count * 8) * 1175 MAX_DPCD_BUFFER_SIZE; 1176 1177 if (g_edid_break == 1) 1178 break; 1179 1180 ret = segments_edid_read(ctx, count / 2, 1181 pblock_buf, offset); 1182 if (ret < 0) 1183 return ret; 1184 1185 memcpy(&pedid_blocks_buf[edid_pos], 1186 pblock_buf, 1187 MAX_DPCD_BUFFER_SIZE); 1188 offset = offset + 0x10; 1189 } 1190 1191 break; 1192 case 3: 1193 offset = 0x80; 1194 1195 for (j = 0; j < 8; j++) { 1196 edid_pos = (j + count * 8) * 1197 MAX_DPCD_BUFFER_SIZE; 1198 if (g_edid_break == 1) 1199 break; 1200 1201 ret = segments_edid_read(ctx, count / 2, 1202 pblock_buf, offset); 1203 if (ret < 0) 1204 return ret; 1205 1206 memcpy(&pedid_blocks_buf[edid_pos], 1207 pblock_buf, 1208 MAX_DPCD_BUFFER_SIZE); 1209 offset = offset + 0x10; 1210 } 1211 1212 break; 1213 default: 1214 break; 1215 } 1216 1217 count++; 1218 1219 } while (blocks_num >= count); 1220 1221 /* Check edid data */ 1222 if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) { 1223 DRM_DEV_ERROR(dev, "WARNING! edid check fail!\n"); 1224 return -EINVAL; 1225 } 1226 1227 /* Reset aux channel */ 1228 ret = sp_tx_rst_aux(ctx); 1229 if (ret < 0) { 1230 DRM_DEV_ERROR(dev, "Failed to reset aux channel!\n"); 1231 return ret; 1232 } 1233 1234 return (blocks_num + 1); 1235 } 1236 1237 static void anx7625_power_on(struct anx7625_data *ctx) 1238 { 1239 struct device *dev = &ctx->client->dev; 1240 int ret, i; 1241 1242 if (!ctx->pdata.low_power_mode) { 1243 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1244 return; 1245 } 1246 1247 for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) { 1248 ret = regulator_enable(ctx->pdata.supplies[i].consumer); 1249 if (ret < 0) { 1250 DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n", 1251 i, ret); 1252 goto reg_err; 1253 } 1254 usleep_range(2000, 2100); 1255 } 1256 1257 usleep_range(11000, 12000); 1258 1259 /* Power on pin enable */ 1260 gpiod_set_value(ctx->pdata.gpio_p_on, 1); 1261 usleep_range(10000, 11000); 1262 /* Power reset pin enable */ 1263 gpiod_set_value(ctx->pdata.gpio_reset, 1); 1264 usleep_range(10000, 11000); 1265 1266 DRM_DEV_DEBUG_DRIVER(dev, "power on !\n"); 1267 return; 1268 reg_err: 1269 for (--i; i >= 0; i--) 1270 regulator_disable(ctx->pdata.supplies[i].consumer); 1271 } 1272 1273 static void anx7625_power_standby(struct anx7625_data *ctx) 1274 { 1275 struct device *dev = &ctx->client->dev; 1276 int ret; 1277 1278 if (!ctx->pdata.low_power_mode) { 1279 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1280 return; 1281 } 1282 1283 gpiod_set_value(ctx->pdata.gpio_reset, 0); 1284 usleep_range(1000, 1100); 1285 gpiod_set_value(ctx->pdata.gpio_p_on, 0); 1286 usleep_range(1000, 1100); 1287 1288 ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies), 1289 ctx->pdata.supplies); 1290 if (ret < 0) 1291 DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret); 1292 1293 DRM_DEV_DEBUG_DRIVER(dev, "power down\n"); 1294 } 1295 1296 /* Basic configurations of ANX7625 */ 1297 static void anx7625_config(struct anx7625_data *ctx) 1298 { 1299 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1300 XTAL_FRQ_SEL, XTAL_FRQ_27M); 1301 } 1302 1303 static void anx7625_disable_pd_protocol(struct anx7625_data *ctx) 1304 { 1305 struct device *dev = &ctx->client->dev; 1306 int ret; 1307 1308 /* Reset main ocm */ 1309 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40); 1310 /* Disable PD */ 1311 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1312 AP_AV_STATUS, AP_DISABLE_PD); 1313 /* Release main ocm */ 1314 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00); 1315 1316 if (ret < 0) 1317 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature fail.\n"); 1318 else 1319 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n"); 1320 } 1321 1322 static int anx7625_ocm_loading_check(struct anx7625_data *ctx) 1323 { 1324 int ret; 1325 struct device *dev = &ctx->client->dev; 1326 1327 /* Check interface workable */ 1328 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1329 FLASH_LOAD_STA); 1330 if (ret < 0) { 1331 DRM_DEV_ERROR(dev, "IO error : access flash load.\n"); 1332 return ret; 1333 } 1334 if ((ret & FLASH_LOAD_STA_CHK) != FLASH_LOAD_STA_CHK) 1335 return -ENODEV; 1336 1337 anx7625_disable_pd_protocol(ctx); 1338 1339 DRM_DEV_DEBUG_DRIVER(dev, "Firmware ver %02x%02x,", 1340 anx7625_reg_read(ctx, 1341 ctx->i2c.rx_p0_client, 1342 OCM_FW_VERSION), 1343 anx7625_reg_read(ctx, 1344 ctx->i2c.rx_p0_client, 1345 OCM_FW_REVERSION)); 1346 DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n", 1347 ANX7625_DRV_VERSION); 1348 1349 return 0; 1350 } 1351 1352 static void anx7625_power_on_init(struct anx7625_data *ctx) 1353 { 1354 int retry_count, i; 1355 1356 for (retry_count = 0; retry_count < 3; retry_count++) { 1357 anx7625_power_on(ctx); 1358 anx7625_config(ctx); 1359 1360 for (i = 0; i < OCM_LOADING_TIME; i++) { 1361 if (!anx7625_ocm_loading_check(ctx)) 1362 return; 1363 usleep_range(1000, 1100); 1364 } 1365 anx7625_power_standby(ctx); 1366 } 1367 } 1368 1369 static void anx7625_init_gpio(struct anx7625_data *platform) 1370 { 1371 struct device *dev = &platform->client->dev; 1372 1373 DRM_DEV_DEBUG_DRIVER(dev, "init gpio\n"); 1374 1375 /* Gpio for chip power enable */ 1376 platform->pdata.gpio_p_on = 1377 devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); 1378 if (IS_ERR_OR_NULL(platform->pdata.gpio_p_on)) { 1379 DRM_DEV_DEBUG_DRIVER(dev, "no enable gpio found\n"); 1380 platform->pdata.gpio_p_on = NULL; 1381 } 1382 1383 /* Gpio for chip reset */ 1384 platform->pdata.gpio_reset = 1385 devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1386 if (IS_ERR_OR_NULL(platform->pdata.gpio_reset)) { 1387 DRM_DEV_DEBUG_DRIVER(dev, "no reset gpio found\n"); 1388 platform->pdata.gpio_reset = NULL; 1389 } 1390 1391 if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) { 1392 platform->pdata.low_power_mode = 1; 1393 DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n", 1394 desc_to_gpio(platform->pdata.gpio_p_on), 1395 desc_to_gpio(platform->pdata.gpio_reset)); 1396 } else { 1397 platform->pdata.low_power_mode = 0; 1398 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n"); 1399 } 1400 } 1401 1402 static void anx7625_stop_dp_work(struct anx7625_data *ctx) 1403 { 1404 ctx->hpd_status = 0; 1405 ctx->hpd_high_cnt = 0; 1406 ctx->display_timing_valid = 0; 1407 } 1408 1409 static void anx7625_start_dp_work(struct anx7625_data *ctx) 1410 { 1411 int ret; 1412 struct device *dev = &ctx->client->dev; 1413 1414 if (ctx->hpd_high_cnt >= 2) { 1415 DRM_DEV_DEBUG_DRIVER(dev, "filter useless HPD\n"); 1416 return; 1417 } 1418 1419 ctx->hpd_status = 1; 1420 ctx->hpd_high_cnt++; 1421 1422 /* Not support HDCP */ 1423 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 1424 1425 /* Try auth flag */ 1426 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 1427 /* Interrupt for DRM */ 1428 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 1429 if (ret < 0) { 1430 DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); 1431 return; 1432 } 1433 1434 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); 1435 if (ret < 0) 1436 return; 1437 1438 DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret); 1439 } 1440 1441 static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx) 1442 { 1443 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS); 1444 } 1445 1446 static void anx7625_hpd_polling(struct anx7625_data *ctx) 1447 { 1448 int ret, val; 1449 struct device *dev = &ctx->client->dev; 1450 1451 /* Interrupt mode, no need poll HPD status, just return */ 1452 if (ctx->pdata.intp_irq) 1453 return; 1454 1455 ret = readx_poll_timeout(anx7625_read_hpd_status_p0, 1456 ctx, val, 1457 ((val & HPD_STATUS) || (val < 0)), 1458 5000, 1459 5000 * 100); 1460 if (ret) { 1461 DRM_DEV_ERROR(dev, "no hpd.\n"); 1462 return; 1463 } 1464 1465 DRM_DEV_DEBUG_DRIVER(dev, "system status: 0x%x. HPD raise up.\n", val); 1466 anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1467 INTR_ALERT_1, 0xFF); 1468 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1469 INTERFACE_CHANGE_INT, 0); 1470 1471 anx7625_start_dp_work(ctx); 1472 1473 if (!ctx->pdata.panel_bridge && ctx->bridge_attached) 1474 drm_helper_hpd_irq_event(ctx->bridge.dev); 1475 } 1476 1477 static void anx7625_remove_edid(struct anx7625_data *ctx) 1478 { 1479 ctx->slimport_edid_p.edid_block_num = -1; 1480 } 1481 1482 static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) 1483 { 1484 int i; 1485 1486 for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) 1487 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1488 DP_TX_LANE0_SWING_REG0 + i, 1489 ctx->pdata.lane0_reg_data[i]); 1490 1491 for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) 1492 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1493 DP_TX_LANE1_SWING_REG0 + i, 1494 ctx->pdata.lane1_reg_data[i]); 1495 } 1496 1497 static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) 1498 { 1499 struct device *dev = &ctx->client->dev; 1500 1501 /* HPD changed */ 1502 DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n", 1503 (u32)on); 1504 1505 if (on == 0) { 1506 DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n"); 1507 anx7625_remove_edid(ctx); 1508 anx7625_stop_dp_work(ctx); 1509 } else { 1510 DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); 1511 anx7625_start_dp_work(ctx); 1512 anx7625_dp_adjust_swing(ctx); 1513 } 1514 } 1515 1516 static int anx7625_hpd_change_detect(struct anx7625_data *ctx) 1517 { 1518 int intr_vector, status; 1519 struct device *dev = &ctx->client->dev; 1520 1521 status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1522 INTR_ALERT_1, 0xFF); 1523 if (status < 0) { 1524 DRM_DEV_ERROR(dev, "cannot clear alert reg.\n"); 1525 return status; 1526 } 1527 1528 intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1529 INTERFACE_CHANGE_INT); 1530 if (intr_vector < 0) { 1531 DRM_DEV_ERROR(dev, "cannot access interrupt change reg.\n"); 1532 return intr_vector; 1533 } 1534 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector); 1535 status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1536 INTERFACE_CHANGE_INT, 1537 intr_vector & (~intr_vector)); 1538 if (status < 0) { 1539 DRM_DEV_ERROR(dev, "cannot clear interrupt change reg.\n"); 1540 return status; 1541 } 1542 1543 if (!(intr_vector & HPD_STATUS_CHANGE)) 1544 return -ENOENT; 1545 1546 status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1547 SYSTEM_STSTUS); 1548 if (status < 0) { 1549 DRM_DEV_ERROR(dev, "cannot clear interrupt status.\n"); 1550 return status; 1551 } 1552 1553 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status); 1554 dp_hpd_change_handler(ctx, status & HPD_STATUS); 1555 1556 return 0; 1557 } 1558 1559 static void anx7625_work_func(struct work_struct *work) 1560 { 1561 int event; 1562 struct anx7625_data *ctx = container_of(work, 1563 struct anx7625_data, work); 1564 1565 mutex_lock(&ctx->lock); 1566 1567 if (pm_runtime_suspended(&ctx->client->dev)) 1568 goto unlock; 1569 1570 event = anx7625_hpd_change_detect(ctx); 1571 if (event < 0) 1572 goto unlock; 1573 1574 if (ctx->bridge_attached) 1575 drm_helper_hpd_irq_event(ctx->bridge.dev); 1576 1577 unlock: 1578 mutex_unlock(&ctx->lock); 1579 } 1580 1581 static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) 1582 { 1583 struct anx7625_data *ctx = (struct anx7625_data *)data; 1584 1585 queue_work(ctx->workqueue, &ctx->work); 1586 1587 return IRQ_HANDLED; 1588 } 1589 1590 static int anx7625_get_swing_setting(struct device *dev, 1591 struct anx7625_platform_data *pdata) 1592 { 1593 int num_regs; 1594 1595 if (of_get_property(dev->of_node, 1596 "analogix,lane0-swing", &num_regs)) { 1597 if (num_regs > DP_TX_SWING_REG_CNT) 1598 num_regs = DP_TX_SWING_REG_CNT; 1599 1600 pdata->dp_lane0_swing_reg_cnt = num_regs; 1601 of_property_read_u8_array(dev->of_node, "analogix,lane0-swing", 1602 pdata->lane0_reg_data, num_regs); 1603 } 1604 1605 if (of_get_property(dev->of_node, 1606 "analogix,lane1-swing", &num_regs)) { 1607 if (num_regs > DP_TX_SWING_REG_CNT) 1608 num_regs = DP_TX_SWING_REG_CNT; 1609 1610 pdata->dp_lane1_swing_reg_cnt = num_regs; 1611 of_property_read_u8_array(dev->of_node, "analogix,lane1-swing", 1612 pdata->lane1_reg_data, num_regs); 1613 } 1614 1615 return 0; 1616 } 1617 1618 static int anx7625_parse_dt(struct device *dev, 1619 struct anx7625_platform_data *pdata) 1620 { 1621 struct device_node *np = dev->of_node, *ep0; 1622 int bus_type, mipi_lanes; 1623 1624 anx7625_get_swing_setting(dev, pdata); 1625 1626 pdata->is_dpi = 1; /* default dpi mode */ 1627 pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); 1628 if (!pdata->mipi_host_node) { 1629 DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); 1630 return -ENODEV; 1631 } 1632 1633 bus_type = V4L2_FWNODE_BUS_TYPE_PARALLEL; 1634 mipi_lanes = MAX_LANES_SUPPORT; 1635 ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); 1636 if (ep0) { 1637 if (of_property_read_u32(ep0, "bus-type", &bus_type)) 1638 bus_type = 0; 1639 1640 mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes"); 1641 } 1642 1643 if (bus_type == V4L2_FWNODE_BUS_TYPE_PARALLEL) /* bus type is Parallel(DSI) */ 1644 pdata->is_dpi = 0; 1645 1646 pdata->mipi_lanes = mipi_lanes; 1647 if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0) 1648 pdata->mipi_lanes = MAX_LANES_SUPPORT; 1649 1650 if (pdata->is_dpi) 1651 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); 1652 else 1653 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); 1654 1655 if (of_property_read_bool(np, "analogix,audio-enable")) 1656 pdata->audio_en = 1; 1657 1658 pdata->panel_bridge = devm_drm_of_get_bridge(dev, np, 1, 0); 1659 if (IS_ERR(pdata->panel_bridge)) { 1660 if (PTR_ERR(pdata->panel_bridge) == -ENODEV) 1661 return 0; 1662 1663 return PTR_ERR(pdata->panel_bridge); 1664 } 1665 1666 DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n"); 1667 1668 return 0; 1669 } 1670 1671 static bool anx7625_of_panel_on_aux_bus(struct device *dev) 1672 { 1673 struct device_node *bus, *panel; 1674 1675 bus = of_get_child_by_name(dev->of_node, "aux-bus"); 1676 if (!bus) 1677 return false; 1678 1679 panel = of_get_child_by_name(bus, "panel"); 1680 of_node_put(bus); 1681 if (!panel) 1682 return false; 1683 of_node_put(panel); 1684 1685 return true; 1686 } 1687 1688 static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge) 1689 { 1690 return container_of(bridge, struct anx7625_data, bridge); 1691 } 1692 1693 static ssize_t anx7625_aux_transfer(struct drm_dp_aux *aux, 1694 struct drm_dp_aux_msg *msg) 1695 { 1696 struct anx7625_data *ctx = container_of(aux, struct anx7625_data, aux); 1697 struct device *dev = &ctx->client->dev; 1698 u8 request = msg->request & ~DP_AUX_I2C_MOT; 1699 int ret = 0; 1700 1701 pm_runtime_get_sync(dev); 1702 msg->reply = 0; 1703 switch (request) { 1704 case DP_AUX_NATIVE_WRITE: 1705 case DP_AUX_I2C_WRITE: 1706 case DP_AUX_NATIVE_READ: 1707 case DP_AUX_I2C_READ: 1708 break; 1709 default: 1710 ret = -EINVAL; 1711 } 1712 if (!ret) 1713 ret = anx7625_aux_trans(ctx, msg->request, msg->address, 1714 msg->size, msg->buffer); 1715 pm_runtime_mark_last_busy(dev); 1716 pm_runtime_put_autosuspend(dev); 1717 1718 return ret; 1719 } 1720 1721 static struct edid *anx7625_get_edid(struct anx7625_data *ctx) 1722 { 1723 struct device *dev = &ctx->client->dev; 1724 struct s_edid_data *p_edid = &ctx->slimport_edid_p; 1725 int edid_num; 1726 u8 *edid; 1727 1728 edid = kmalloc(FOUR_BLOCK_SIZE, GFP_KERNEL); 1729 if (!edid) { 1730 DRM_DEV_ERROR(dev, "Fail to allocate buffer\n"); 1731 return NULL; 1732 } 1733 1734 if (ctx->slimport_edid_p.edid_block_num > 0) { 1735 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, 1736 FOUR_BLOCK_SIZE); 1737 return (struct edid *)edid; 1738 } 1739 1740 pm_runtime_get_sync(dev); 1741 edid_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data); 1742 pm_runtime_put_sync(dev); 1743 1744 if (edid_num < 1) { 1745 DRM_DEV_ERROR(dev, "Fail to read EDID: %d\n", edid_num); 1746 kfree(edid); 1747 return NULL; 1748 } 1749 1750 p_edid->edid_block_num = edid_num; 1751 1752 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, FOUR_BLOCK_SIZE); 1753 return (struct edid *)edid; 1754 } 1755 1756 static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) 1757 { 1758 struct device *dev = &ctx->client->dev; 1759 1760 DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); 1761 1762 if (ctx->pdata.panel_bridge) 1763 return connector_status_connected; 1764 1765 return ctx->hpd_status ? connector_status_connected : 1766 connector_status_disconnected; 1767 } 1768 1769 static int anx7625_audio_hw_params(struct device *dev, void *data, 1770 struct hdmi_codec_daifmt *fmt, 1771 struct hdmi_codec_params *params) 1772 { 1773 struct anx7625_data *ctx = dev_get_drvdata(dev); 1774 int wl, ch, rate; 1775 int ret = 0; 1776 1777 if (fmt->fmt != HDMI_DSP_A) { 1778 DRM_DEV_ERROR(dev, "only supports DSP_A\n"); 1779 return -EINVAL; 1780 } 1781 1782 DRM_DEV_DEBUG_DRIVER(dev, "setting %d Hz, %d bit, %d channels\n", 1783 params->sample_rate, params->sample_width, 1784 params->cea.channels); 1785 1786 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1787 AUDIO_CHANNEL_STATUS_6, 1788 ~I2S_SLAVE_MODE, 1789 TDM_SLAVE_MODE); 1790 1791 /* Word length */ 1792 switch (params->sample_width) { 1793 case 16: 1794 wl = AUDIO_W_LEN_16_20MAX; 1795 break; 1796 case 18: 1797 wl = AUDIO_W_LEN_18_20MAX; 1798 break; 1799 case 20: 1800 wl = AUDIO_W_LEN_20_20MAX; 1801 break; 1802 case 24: 1803 wl = AUDIO_W_LEN_24_24MAX; 1804 break; 1805 default: 1806 DRM_DEV_DEBUG_DRIVER(dev, "wordlength: %d bit not support", 1807 params->sample_width); 1808 return -EINVAL; 1809 } 1810 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1811 AUDIO_CHANNEL_STATUS_5, 1812 0xf0, wl); 1813 1814 /* Channel num */ 1815 switch (params->cea.channels) { 1816 case 2: 1817 ch = I2S_CH_2; 1818 break; 1819 case 4: 1820 ch = TDM_CH_4; 1821 break; 1822 case 6: 1823 ch = TDM_CH_6; 1824 break; 1825 case 8: 1826 ch = TDM_CH_8; 1827 break; 1828 default: 1829 DRM_DEV_DEBUG_DRIVER(dev, "channel number: %d not support", 1830 params->cea.channels); 1831 return -EINVAL; 1832 } 1833 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1834 AUDIO_CHANNEL_STATUS_6, 0x1f, ch << 5); 1835 if (ch > I2S_CH_2) 1836 ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 1837 AUDIO_CHANNEL_STATUS_6, AUDIO_LAYOUT); 1838 else 1839 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 1840 AUDIO_CHANNEL_STATUS_6, ~AUDIO_LAYOUT); 1841 1842 /* FS */ 1843 switch (params->sample_rate) { 1844 case 32000: 1845 rate = AUDIO_FS_32K; 1846 break; 1847 case 44100: 1848 rate = AUDIO_FS_441K; 1849 break; 1850 case 48000: 1851 rate = AUDIO_FS_48K; 1852 break; 1853 case 88200: 1854 rate = AUDIO_FS_882K; 1855 break; 1856 case 96000: 1857 rate = AUDIO_FS_96K; 1858 break; 1859 case 176400: 1860 rate = AUDIO_FS_1764K; 1861 break; 1862 case 192000: 1863 rate = AUDIO_FS_192K; 1864 break; 1865 default: 1866 DRM_DEV_DEBUG_DRIVER(dev, "sample rate: %d not support", 1867 params->sample_rate); 1868 return -EINVAL; 1869 } 1870 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1871 AUDIO_CHANNEL_STATUS_4, 1872 0xf0, rate); 1873 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1874 AP_AV_STATUS, AP_AUDIO_CHG); 1875 if (ret < 0) { 1876 DRM_DEV_ERROR(dev, "IO error : config audio.\n"); 1877 return -EIO; 1878 } 1879 1880 return 0; 1881 } 1882 1883 static void anx7625_audio_shutdown(struct device *dev, void *data) 1884 { 1885 DRM_DEV_DEBUG_DRIVER(dev, "stop audio\n"); 1886 } 1887 1888 static int anx7625_hdmi_i2s_get_dai_id(struct snd_soc_component *component, 1889 struct device_node *endpoint) 1890 { 1891 struct of_endpoint of_ep; 1892 int ret; 1893 1894 ret = of_graph_parse_endpoint(endpoint, &of_ep); 1895 if (ret < 0) 1896 return ret; 1897 1898 /* 1899 * HDMI sound should be located at external DPI port 1900 * Didn't have good way to check where is internal(DSI) 1901 * or external(DPI) bridge 1902 */ 1903 return 0; 1904 } 1905 1906 static void 1907 anx7625_audio_update_connector_status(struct anx7625_data *ctx, 1908 enum drm_connector_status status) 1909 { 1910 if (ctx->plugged_cb && ctx->codec_dev) { 1911 ctx->plugged_cb(ctx->codec_dev, 1912 status == connector_status_connected); 1913 } 1914 } 1915 1916 static int anx7625_audio_hook_plugged_cb(struct device *dev, void *data, 1917 hdmi_codec_plugged_cb fn, 1918 struct device *codec_dev) 1919 { 1920 struct anx7625_data *ctx = data; 1921 1922 ctx->plugged_cb = fn; 1923 ctx->codec_dev = codec_dev; 1924 anx7625_audio_update_connector_status(ctx, anx7625_sink_detect(ctx)); 1925 1926 return 0; 1927 } 1928 1929 static int anx7625_audio_get_eld(struct device *dev, void *data, 1930 u8 *buf, size_t len) 1931 { 1932 struct anx7625_data *ctx = dev_get_drvdata(dev); 1933 1934 if (!ctx->connector) { 1935 /* Pass en empty ELD if connector not available */ 1936 memset(buf, 0, len); 1937 } else { 1938 dev_dbg(dev, "audio copy eld\n"); 1939 memcpy(buf, ctx->connector->eld, 1940 min(sizeof(ctx->connector->eld), len)); 1941 } 1942 1943 return 0; 1944 } 1945 1946 static const struct hdmi_codec_ops anx7625_codec_ops = { 1947 .hw_params = anx7625_audio_hw_params, 1948 .audio_shutdown = anx7625_audio_shutdown, 1949 .get_eld = anx7625_audio_get_eld, 1950 .get_dai_id = anx7625_hdmi_i2s_get_dai_id, 1951 .hook_plugged_cb = anx7625_audio_hook_plugged_cb, 1952 }; 1953 1954 static void anx7625_unregister_audio(struct anx7625_data *ctx) 1955 { 1956 struct device *dev = &ctx->client->dev; 1957 1958 if (ctx->audio_pdev) { 1959 platform_device_unregister(ctx->audio_pdev); 1960 ctx->audio_pdev = NULL; 1961 } 1962 1963 DRM_DEV_DEBUG_DRIVER(dev, "unbound to %s", HDMI_CODEC_DRV_NAME); 1964 } 1965 1966 static int anx7625_register_audio(struct device *dev, struct anx7625_data *ctx) 1967 { 1968 struct hdmi_codec_pdata codec_data = { 1969 .ops = &anx7625_codec_ops, 1970 .max_i2s_channels = 8, 1971 .i2s = 1, 1972 .data = ctx, 1973 }; 1974 1975 ctx->audio_pdev = platform_device_register_data(dev, 1976 HDMI_CODEC_DRV_NAME, 1977 PLATFORM_DEVID_AUTO, 1978 &codec_data, 1979 sizeof(codec_data)); 1980 1981 if (IS_ERR(ctx->audio_pdev)) 1982 return PTR_ERR(ctx->audio_pdev); 1983 1984 DRM_DEV_DEBUG_DRIVER(dev, "bound to %s", HDMI_CODEC_DRV_NAME); 1985 1986 return 0; 1987 } 1988 1989 static int anx7625_attach_dsi(struct anx7625_data *ctx) 1990 { 1991 struct mipi_dsi_device *dsi; 1992 struct device *dev = &ctx->client->dev; 1993 struct mipi_dsi_host *host; 1994 const struct mipi_dsi_device_info info = { 1995 .type = "anx7625", 1996 .channel = 0, 1997 .node = NULL, 1998 }; 1999 int ret; 2000 2001 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n"); 2002 2003 host = of_find_mipi_dsi_host_by_node(ctx->pdata.mipi_host_node); 2004 if (!host) { 2005 DRM_DEV_ERROR(dev, "fail to find dsi host.\n"); 2006 return -EPROBE_DEFER; 2007 } 2008 2009 dsi = devm_mipi_dsi_device_register_full(dev, host, &info); 2010 if (IS_ERR(dsi)) { 2011 DRM_DEV_ERROR(dev, "fail to create dsi device.\n"); 2012 return -EINVAL; 2013 } 2014 2015 dsi->lanes = ctx->pdata.mipi_lanes; 2016 dsi->format = MIPI_DSI_FMT_RGB888; 2017 dsi->mode_flags = MIPI_DSI_MODE_VIDEO | 2018 MIPI_DSI_MODE_VIDEO_SYNC_PULSE | 2019 MIPI_DSI_MODE_VIDEO_HSE | 2020 MIPI_DSI_HS_PKT_END_ALIGNED; 2021 2022 ret = devm_mipi_dsi_attach(dev, dsi); 2023 if (ret) { 2024 DRM_DEV_ERROR(dev, "fail to attach dsi to host.\n"); 2025 return ret; 2026 } 2027 2028 ctx->dsi = dsi; 2029 2030 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n"); 2031 2032 return 0; 2033 } 2034 2035 static void hdcp_check_work_func(struct work_struct *work) 2036 { 2037 u8 status; 2038 struct delayed_work *dwork; 2039 struct anx7625_data *ctx; 2040 struct device *dev; 2041 struct drm_device *drm_dev; 2042 2043 dwork = to_delayed_work(work); 2044 ctx = container_of(dwork, struct anx7625_data, hdcp_work); 2045 dev = &ctx->client->dev; 2046 2047 if (!ctx->connector) { 2048 dev_err(dev, "HDCP connector is null!"); 2049 return; 2050 } 2051 2052 drm_dev = ctx->connector->dev; 2053 drm_modeset_lock(&drm_dev->mode_config.connection_mutex, NULL); 2054 mutex_lock(&ctx->hdcp_wq_lock); 2055 2056 status = anx7625_reg_read(ctx, ctx->i2c.tx_p0_client, 0); 2057 dev_dbg(dev, "sink HDCP status check: %.02x\n", status); 2058 if (status & BIT(1)) { 2059 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_ENABLED; 2060 drm_hdcp_update_content_protection(ctx->connector, 2061 ctx->hdcp_cp); 2062 dev_dbg(dev, "update CP to ENABLE\n"); 2063 } 2064 2065 mutex_unlock(&ctx->hdcp_wq_lock); 2066 drm_modeset_unlock(&drm_dev->mode_config.connection_mutex); 2067 } 2068 2069 static int anx7625_connector_atomic_check(struct anx7625_data *ctx, 2070 struct drm_connector_state *state) 2071 { 2072 struct device *dev = &ctx->client->dev; 2073 int cp; 2074 2075 dev_dbg(dev, "hdcp state check\n"); 2076 cp = state->content_protection; 2077 2078 if (cp == ctx->hdcp_cp) 2079 return 0; 2080 2081 if (cp == DRM_MODE_CONTENT_PROTECTION_DESIRED) { 2082 if (ctx->dp_en) { 2083 dev_dbg(dev, "enable HDCP\n"); 2084 anx7625_hdcp_enable(ctx); 2085 2086 queue_delayed_work(ctx->hdcp_workqueue, 2087 &ctx->hdcp_work, 2088 msecs_to_jiffies(2000)); 2089 } 2090 } 2091 2092 if (cp == DRM_MODE_CONTENT_PROTECTION_UNDESIRED) { 2093 if (ctx->hdcp_cp != DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2094 dev_err(dev, "current CP is not ENABLED\n"); 2095 return -EINVAL; 2096 } 2097 anx7625_hdcp_disable(ctx); 2098 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 2099 drm_hdcp_update_content_protection(ctx->connector, 2100 ctx->hdcp_cp); 2101 dev_dbg(dev, "update CP to UNDESIRE\n"); 2102 } 2103 2104 if (cp == DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2105 dev_err(dev, "Userspace illegal set to PROTECTION ENABLE\n"); 2106 return -EINVAL; 2107 } 2108 2109 return 0; 2110 } 2111 2112 static int anx7625_bridge_attach(struct drm_bridge *bridge, 2113 enum drm_bridge_attach_flags flags) 2114 { 2115 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2116 int err; 2117 struct device *dev = &ctx->client->dev; 2118 2119 DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n"); 2120 if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) 2121 return -EINVAL; 2122 2123 if (!bridge->encoder) { 2124 DRM_DEV_ERROR(dev, "Parent encoder object not found"); 2125 return -ENODEV; 2126 } 2127 2128 ctx->aux.drm_dev = bridge->dev; 2129 err = drm_dp_aux_register(&ctx->aux); 2130 if (err) { 2131 dev_err(dev, "failed to register aux channel: %d\n", err); 2132 return err; 2133 } 2134 2135 if (ctx->pdata.panel_bridge) { 2136 err = drm_bridge_attach(bridge->encoder, 2137 ctx->pdata.panel_bridge, 2138 &ctx->bridge, flags); 2139 if (err) 2140 return err; 2141 } 2142 2143 ctx->bridge_attached = 1; 2144 2145 return 0; 2146 } 2147 2148 static void anx7625_bridge_detach(struct drm_bridge *bridge) 2149 { 2150 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2151 2152 drm_dp_aux_unregister(&ctx->aux); 2153 } 2154 2155 static enum drm_mode_status 2156 anx7625_bridge_mode_valid(struct drm_bridge *bridge, 2157 const struct drm_display_info *info, 2158 const struct drm_display_mode *mode) 2159 { 2160 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2161 struct device *dev = &ctx->client->dev; 2162 2163 DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n"); 2164 2165 /* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */ 2166 if (mode->clock > SUPPORT_PIXEL_CLOCK) { 2167 DRM_DEV_DEBUG_DRIVER(dev, 2168 "drm mode invalid, pixelclock too high.\n"); 2169 return MODE_CLOCK_HIGH; 2170 } 2171 2172 DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n"); 2173 2174 return MODE_OK; 2175 } 2176 2177 static void anx7625_bridge_mode_set(struct drm_bridge *bridge, 2178 const struct drm_display_mode *old_mode, 2179 const struct drm_display_mode *mode) 2180 { 2181 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2182 struct device *dev = &ctx->client->dev; 2183 2184 DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n"); 2185 2186 ctx->dt.pixelclock.min = mode->clock; 2187 ctx->dt.hactive.min = mode->hdisplay; 2188 ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start; 2189 ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay; 2190 ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end; 2191 ctx->dt.vactive.min = mode->vdisplay; 2192 ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start; 2193 ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay; 2194 ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end; 2195 2196 ctx->display_timing_valid = 1; 2197 2198 DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min); 2199 DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n", 2200 ctx->dt.hactive.min, 2201 ctx->dt.hsync_len.min, 2202 ctx->dt.hfront_porch.min, 2203 ctx->dt.hback_porch.min); 2204 DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n", 2205 ctx->dt.vactive.min, 2206 ctx->dt.vsync_len.min, 2207 ctx->dt.vfront_porch.min, 2208 ctx->dt.vback_porch.min); 2209 DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n", 2210 mode->hdisplay, 2211 mode->hsync_start); 2212 DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n", 2213 mode->hsync_end, 2214 mode->htotal); 2215 DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n", 2216 mode->vdisplay, 2217 mode->vsync_start); 2218 DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n", 2219 mode->vsync_end, 2220 mode->vtotal); 2221 } 2222 2223 static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, 2224 const struct drm_display_mode *mode, 2225 struct drm_display_mode *adj) 2226 { 2227 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2228 struct device *dev = &ctx->client->dev; 2229 u32 hsync, hfp, hbp, hblanking; 2230 u32 adj_hsync, adj_hfp, adj_hbp, adj_hblanking, delta_adj; 2231 u32 vref, adj_clock; 2232 2233 DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); 2234 2235 /* No need fixup for external monitor */ 2236 if (!ctx->pdata.panel_bridge) 2237 return true; 2238 2239 hsync = mode->hsync_end - mode->hsync_start; 2240 hfp = mode->hsync_start - mode->hdisplay; 2241 hbp = mode->htotal - mode->hsync_end; 2242 hblanking = mode->htotal - mode->hdisplay; 2243 2244 DRM_DEV_DEBUG_DRIVER(dev, "before mode fixup\n"); 2245 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2246 hsync, hfp, hbp, adj->clock); 2247 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2248 adj->hsync_start, adj->hsync_end, adj->htotal); 2249 2250 adj_hfp = hfp; 2251 adj_hsync = hsync; 2252 adj_hbp = hbp; 2253 adj_hblanking = hblanking; 2254 2255 /* HFP needs to be even */ 2256 if (hfp & 0x1) { 2257 adj_hfp += 1; 2258 adj_hblanking += 1; 2259 } 2260 2261 /* HBP needs to be even */ 2262 if (hbp & 0x1) { 2263 adj_hbp -= 1; 2264 adj_hblanking -= 1; 2265 } 2266 2267 /* HSYNC needs to be even */ 2268 if (hsync & 0x1) { 2269 if (adj_hblanking < hblanking) 2270 adj_hsync += 1; 2271 else 2272 adj_hsync -= 1; 2273 } 2274 2275 /* 2276 * Once illegal timing detected, use default HFP, HSYNC, HBP 2277 * This adjusting made for built-in eDP panel, for the externel 2278 * DP monitor, may need return false. 2279 */ 2280 if (hblanking < HBLANKING_MIN || (hfp < HP_MIN && hbp < HP_MIN)) { 2281 adj_hsync = SYNC_LEN_DEF; 2282 adj_hfp = HFP_HBP_DEF; 2283 adj_hbp = HFP_HBP_DEF; 2284 vref = adj->clock * 1000 / (adj->htotal * adj->vtotal); 2285 if (hblanking < HBLANKING_MIN) { 2286 delta_adj = HBLANKING_MIN - hblanking; 2287 adj_clock = vref * delta_adj * adj->vtotal; 2288 adj->clock += DIV_ROUND_UP(adj_clock, 1000); 2289 } else { 2290 delta_adj = hblanking - HBLANKING_MIN; 2291 adj_clock = vref * delta_adj * adj->vtotal; 2292 adj->clock -= DIV_ROUND_UP(adj_clock, 1000); 2293 } 2294 2295 DRM_WARN("illegal hblanking timing, use default.\n"); 2296 DRM_WARN("hfp(%d), hbp(%d), hsync(%d).\n", hfp, hbp, hsync); 2297 } else if (adj_hfp < HP_MIN) { 2298 /* Adjust hfp if hfp less than HP_MIN */ 2299 delta_adj = HP_MIN - adj_hfp; 2300 adj_hfp = HP_MIN; 2301 2302 /* 2303 * Balance total HBlanking pixel, if HBP does not have enough 2304 * space, adjust HSYNC length, otherwise adjust HBP 2305 */ 2306 if ((adj_hbp - delta_adj) < HP_MIN) 2307 /* HBP not enough space */ 2308 adj_hsync -= delta_adj; 2309 else 2310 adj_hbp -= delta_adj; 2311 } else if (adj_hbp < HP_MIN) { 2312 delta_adj = HP_MIN - adj_hbp; 2313 adj_hbp = HP_MIN; 2314 2315 /* 2316 * Balance total HBlanking pixel, if HBP hasn't enough space, 2317 * adjust HSYNC length, otherwize adjust HBP 2318 */ 2319 if ((adj_hfp - delta_adj) < HP_MIN) 2320 /* HFP not enough space */ 2321 adj_hsync -= delta_adj; 2322 else 2323 adj_hfp -= delta_adj; 2324 } 2325 2326 DRM_DEV_DEBUG_DRIVER(dev, "after mode fixup\n"); 2327 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2328 adj_hsync, adj_hfp, adj_hbp, adj->clock); 2329 2330 /* Reconstruct timing */ 2331 adj->hsync_start = adj->hdisplay + adj_hfp; 2332 adj->hsync_end = adj->hsync_start + adj_hsync; 2333 adj->htotal = adj->hsync_end + adj_hbp; 2334 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2335 adj->hsync_start, adj->hsync_end, adj->htotal); 2336 2337 return true; 2338 } 2339 2340 static int anx7625_bridge_atomic_check(struct drm_bridge *bridge, 2341 struct drm_bridge_state *bridge_state, 2342 struct drm_crtc_state *crtc_state, 2343 struct drm_connector_state *conn_state) 2344 { 2345 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2346 struct device *dev = &ctx->client->dev; 2347 2348 dev_dbg(dev, "drm bridge atomic check\n"); 2349 2350 anx7625_bridge_mode_fixup(bridge, &crtc_state->mode, 2351 &crtc_state->adjusted_mode); 2352 2353 return anx7625_connector_atomic_check(ctx, conn_state); 2354 } 2355 2356 static void anx7625_bridge_atomic_enable(struct drm_bridge *bridge, 2357 struct drm_bridge_state *state) 2358 { 2359 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2360 struct device *dev = &ctx->client->dev; 2361 struct drm_connector *connector; 2362 2363 dev_dbg(dev, "drm atomic enable\n"); 2364 2365 if (!bridge->encoder) { 2366 dev_err(dev, "Parent encoder object not found"); 2367 return; 2368 } 2369 2370 connector = drm_atomic_get_new_connector_for_encoder(state->base.state, 2371 bridge->encoder); 2372 if (!connector) 2373 return; 2374 2375 ctx->connector = connector; 2376 2377 pm_runtime_get_sync(dev); 2378 2379 anx7625_dp_start(ctx); 2380 } 2381 2382 static void anx7625_bridge_atomic_disable(struct drm_bridge *bridge, 2383 struct drm_bridge_state *old) 2384 { 2385 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2386 struct device *dev = &ctx->client->dev; 2387 2388 dev_dbg(dev, "drm atomic disable\n"); 2389 2390 ctx->connector = NULL; 2391 anx7625_dp_stop(ctx); 2392 2393 pm_runtime_put_sync(dev); 2394 } 2395 2396 static enum drm_connector_status 2397 anx7625_bridge_detect(struct drm_bridge *bridge) 2398 { 2399 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2400 struct device *dev = &ctx->client->dev; 2401 2402 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge detect\n"); 2403 2404 return anx7625_sink_detect(ctx); 2405 } 2406 2407 static struct edid *anx7625_bridge_get_edid(struct drm_bridge *bridge, 2408 struct drm_connector *connector) 2409 { 2410 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2411 struct device *dev = &ctx->client->dev; 2412 2413 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge get edid\n"); 2414 2415 return anx7625_get_edid(ctx); 2416 } 2417 2418 static const struct drm_bridge_funcs anx7625_bridge_funcs = { 2419 .attach = anx7625_bridge_attach, 2420 .detach = anx7625_bridge_detach, 2421 .mode_valid = anx7625_bridge_mode_valid, 2422 .mode_set = anx7625_bridge_mode_set, 2423 .atomic_check = anx7625_bridge_atomic_check, 2424 .atomic_enable = anx7625_bridge_atomic_enable, 2425 .atomic_disable = anx7625_bridge_atomic_disable, 2426 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 2427 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 2428 .atomic_reset = drm_atomic_helper_bridge_reset, 2429 .detect = anx7625_bridge_detect, 2430 .get_edid = anx7625_bridge_get_edid, 2431 }; 2432 2433 static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx, 2434 struct i2c_client *client) 2435 { 2436 int err = 0; 2437 2438 ctx->i2c.tx_p0_client = i2c_new_dummy_device(client->adapter, 2439 TX_P0_ADDR >> 1); 2440 if (IS_ERR(ctx->i2c.tx_p0_client)) 2441 return PTR_ERR(ctx->i2c.tx_p0_client); 2442 2443 ctx->i2c.tx_p1_client = i2c_new_dummy_device(client->adapter, 2444 TX_P1_ADDR >> 1); 2445 if (IS_ERR(ctx->i2c.tx_p1_client)) { 2446 err = PTR_ERR(ctx->i2c.tx_p1_client); 2447 goto free_tx_p0; 2448 } 2449 2450 ctx->i2c.tx_p2_client = i2c_new_dummy_device(client->adapter, 2451 TX_P2_ADDR >> 1); 2452 if (IS_ERR(ctx->i2c.tx_p2_client)) { 2453 err = PTR_ERR(ctx->i2c.tx_p2_client); 2454 goto free_tx_p1; 2455 } 2456 2457 ctx->i2c.rx_p0_client = i2c_new_dummy_device(client->adapter, 2458 RX_P0_ADDR >> 1); 2459 if (IS_ERR(ctx->i2c.rx_p0_client)) { 2460 err = PTR_ERR(ctx->i2c.rx_p0_client); 2461 goto free_tx_p2; 2462 } 2463 2464 ctx->i2c.rx_p1_client = i2c_new_dummy_device(client->adapter, 2465 RX_P1_ADDR >> 1); 2466 if (IS_ERR(ctx->i2c.rx_p1_client)) { 2467 err = PTR_ERR(ctx->i2c.rx_p1_client); 2468 goto free_rx_p0; 2469 } 2470 2471 ctx->i2c.rx_p2_client = i2c_new_dummy_device(client->adapter, 2472 RX_P2_ADDR >> 1); 2473 if (IS_ERR(ctx->i2c.rx_p2_client)) { 2474 err = PTR_ERR(ctx->i2c.rx_p2_client); 2475 goto free_rx_p1; 2476 } 2477 2478 ctx->i2c.tcpc_client = i2c_new_dummy_device(client->adapter, 2479 TCPC_INTERFACE_ADDR >> 1); 2480 if (IS_ERR(ctx->i2c.tcpc_client)) { 2481 err = PTR_ERR(ctx->i2c.tcpc_client); 2482 goto free_rx_p2; 2483 } 2484 2485 return 0; 2486 2487 free_rx_p2: 2488 i2c_unregister_device(ctx->i2c.rx_p2_client); 2489 free_rx_p1: 2490 i2c_unregister_device(ctx->i2c.rx_p1_client); 2491 free_rx_p0: 2492 i2c_unregister_device(ctx->i2c.rx_p0_client); 2493 free_tx_p2: 2494 i2c_unregister_device(ctx->i2c.tx_p2_client); 2495 free_tx_p1: 2496 i2c_unregister_device(ctx->i2c.tx_p1_client); 2497 free_tx_p0: 2498 i2c_unregister_device(ctx->i2c.tx_p0_client); 2499 2500 return err; 2501 } 2502 2503 static void anx7625_unregister_i2c_dummy_clients(struct anx7625_data *ctx) 2504 { 2505 i2c_unregister_device(ctx->i2c.tx_p0_client); 2506 i2c_unregister_device(ctx->i2c.tx_p1_client); 2507 i2c_unregister_device(ctx->i2c.tx_p2_client); 2508 i2c_unregister_device(ctx->i2c.rx_p0_client); 2509 i2c_unregister_device(ctx->i2c.rx_p1_client); 2510 i2c_unregister_device(ctx->i2c.rx_p2_client); 2511 i2c_unregister_device(ctx->i2c.tcpc_client); 2512 } 2513 2514 static int __maybe_unused anx7625_runtime_pm_suspend(struct device *dev) 2515 { 2516 struct anx7625_data *ctx = dev_get_drvdata(dev); 2517 2518 mutex_lock(&ctx->lock); 2519 2520 anx7625_stop_dp_work(ctx); 2521 anx7625_power_standby(ctx); 2522 2523 mutex_unlock(&ctx->lock); 2524 2525 return 0; 2526 } 2527 2528 static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev) 2529 { 2530 struct anx7625_data *ctx = dev_get_drvdata(dev); 2531 2532 mutex_lock(&ctx->lock); 2533 2534 anx7625_power_on_init(ctx); 2535 anx7625_hpd_polling(ctx); 2536 2537 mutex_unlock(&ctx->lock); 2538 2539 return 0; 2540 } 2541 2542 static int __maybe_unused anx7625_resume(struct device *dev) 2543 { 2544 struct anx7625_data *ctx = dev_get_drvdata(dev); 2545 2546 if (!ctx->pdata.intp_irq) 2547 return 0; 2548 2549 if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev)) { 2550 enable_irq(ctx->pdata.intp_irq); 2551 anx7625_runtime_pm_resume(dev); 2552 } 2553 2554 return 0; 2555 } 2556 2557 static int __maybe_unused anx7625_suspend(struct device *dev) 2558 { 2559 struct anx7625_data *ctx = dev_get_drvdata(dev); 2560 2561 if (!ctx->pdata.intp_irq) 2562 return 0; 2563 2564 if (!pm_runtime_enabled(dev) || !pm_runtime_suspended(dev)) { 2565 anx7625_runtime_pm_suspend(dev); 2566 disable_irq(ctx->pdata.intp_irq); 2567 } 2568 2569 return 0; 2570 } 2571 2572 static const struct dev_pm_ops anx7625_pm_ops = { 2573 SET_SYSTEM_SLEEP_PM_OPS(anx7625_suspend, anx7625_resume) 2574 SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, 2575 anx7625_runtime_pm_resume, NULL) 2576 }; 2577 2578 static void anx7625_runtime_disable(void *data) 2579 { 2580 pm_runtime_dont_use_autosuspend(data); 2581 pm_runtime_disable(data); 2582 } 2583 2584 static int anx7625_i2c_probe(struct i2c_client *client, 2585 const struct i2c_device_id *id) 2586 { 2587 struct anx7625_data *platform; 2588 struct anx7625_platform_data *pdata; 2589 int ret = 0; 2590 struct device *dev = &client->dev; 2591 2592 if (!i2c_check_functionality(client->adapter, 2593 I2C_FUNC_SMBUS_I2C_BLOCK)) { 2594 DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n"); 2595 return -ENODEV; 2596 } 2597 2598 platform = devm_kzalloc(dev, sizeof(*platform), GFP_KERNEL); 2599 if (!platform) { 2600 DRM_DEV_ERROR(dev, "fail to allocate driver data\n"); 2601 return -ENOMEM; 2602 } 2603 2604 pdata = &platform->pdata; 2605 2606 platform->client = client; 2607 i2c_set_clientdata(client, platform); 2608 2609 pdata->supplies[0].supply = "vdd10"; 2610 pdata->supplies[1].supply = "vdd18"; 2611 pdata->supplies[2].supply = "vdd33"; 2612 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies), 2613 pdata->supplies); 2614 if (ret) { 2615 DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret); 2616 return ret; 2617 } 2618 anx7625_init_gpio(platform); 2619 2620 mutex_init(&platform->lock); 2621 mutex_init(&platform->hdcp_wq_lock); 2622 2623 INIT_DELAYED_WORK(&platform->hdcp_work, hdcp_check_work_func); 2624 platform->hdcp_workqueue = create_workqueue("hdcp workqueue"); 2625 if (!platform->hdcp_workqueue) { 2626 dev_err(dev, "fail to create work queue\n"); 2627 ret = -ENOMEM; 2628 return ret; 2629 } 2630 2631 platform->pdata.intp_irq = client->irq; 2632 if (platform->pdata.intp_irq) { 2633 INIT_WORK(&platform->work, anx7625_work_func); 2634 platform->workqueue = alloc_workqueue("anx7625_work", 2635 WQ_FREEZABLE | WQ_MEM_RECLAIM, 1); 2636 if (!platform->workqueue) { 2637 DRM_DEV_ERROR(dev, "fail to create work queue\n"); 2638 ret = -ENOMEM; 2639 goto free_hdcp_wq; 2640 } 2641 2642 ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq, 2643 NULL, anx7625_intr_hpd_isr, 2644 IRQF_TRIGGER_FALLING | 2645 IRQF_ONESHOT, 2646 "anx7625-intp", platform); 2647 if (ret) { 2648 DRM_DEV_ERROR(dev, "fail to request irq\n"); 2649 goto free_wq; 2650 } 2651 } 2652 2653 platform->aux.name = "anx7625-aux"; 2654 platform->aux.dev = dev; 2655 platform->aux.transfer = anx7625_aux_transfer; 2656 drm_dp_aux_init(&platform->aux); 2657 devm_of_dp_aux_populate_ep_devices(&platform->aux); 2658 2659 ret = anx7625_parse_dt(dev, pdata); 2660 if (ret) { 2661 if (ret != -EPROBE_DEFER) 2662 DRM_DEV_ERROR(dev, "fail to parse DT : %d\n", ret); 2663 goto free_wq; 2664 } 2665 2666 if (anx7625_register_i2c_dummy_clients(platform, client) != 0) { 2667 ret = -ENOMEM; 2668 DRM_DEV_ERROR(dev, "fail to reserve I2C bus.\n"); 2669 goto free_wq; 2670 } 2671 2672 pm_runtime_enable(dev); 2673 pm_runtime_set_autosuspend_delay(dev, 1000); 2674 pm_runtime_use_autosuspend(dev); 2675 pm_suspend_ignore_children(dev, true); 2676 ret = devm_add_action_or_reset(dev, anx7625_runtime_disable, dev); 2677 if (ret) 2678 goto free_wq; 2679 2680 if (!platform->pdata.low_power_mode) { 2681 anx7625_disable_pd_protocol(platform); 2682 pm_runtime_get_sync(dev); 2683 } 2684 2685 /* Add work function */ 2686 if (platform->pdata.intp_irq) 2687 queue_work(platform->workqueue, &platform->work); 2688 2689 platform->bridge.funcs = &anx7625_bridge_funcs; 2690 platform->bridge.of_node = client->dev.of_node; 2691 if (!anx7625_of_panel_on_aux_bus(&client->dev)) 2692 platform->bridge.ops |= DRM_BRIDGE_OP_EDID; 2693 if (!platform->pdata.panel_bridge) 2694 platform->bridge.ops |= DRM_BRIDGE_OP_HPD | 2695 DRM_BRIDGE_OP_DETECT; 2696 platform->bridge.type = platform->pdata.panel_bridge ? 2697 DRM_MODE_CONNECTOR_eDP : 2698 DRM_MODE_CONNECTOR_DisplayPort; 2699 2700 drm_bridge_add(&platform->bridge); 2701 2702 if (!platform->pdata.is_dpi) { 2703 ret = anx7625_attach_dsi(platform); 2704 if (ret) { 2705 DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", ret); 2706 goto unregister_bridge; 2707 } 2708 } 2709 2710 if (platform->pdata.audio_en) 2711 anx7625_register_audio(dev, platform); 2712 2713 DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); 2714 2715 return 0; 2716 2717 unregister_bridge: 2718 drm_bridge_remove(&platform->bridge); 2719 2720 if (!platform->pdata.low_power_mode) 2721 pm_runtime_put_sync_suspend(&client->dev); 2722 2723 anx7625_unregister_i2c_dummy_clients(platform); 2724 2725 free_wq: 2726 if (platform->workqueue) 2727 destroy_workqueue(platform->workqueue); 2728 2729 free_hdcp_wq: 2730 if (platform->hdcp_workqueue) 2731 destroy_workqueue(platform->hdcp_workqueue); 2732 2733 return ret; 2734 } 2735 2736 static int anx7625_i2c_remove(struct i2c_client *client) 2737 { 2738 struct anx7625_data *platform = i2c_get_clientdata(client); 2739 2740 drm_bridge_remove(&platform->bridge); 2741 2742 if (platform->pdata.intp_irq) 2743 destroy_workqueue(platform->workqueue); 2744 2745 if (platform->hdcp_workqueue) { 2746 cancel_delayed_work(&platform->hdcp_work); 2747 flush_workqueue(platform->hdcp_workqueue); 2748 destroy_workqueue(platform->hdcp_workqueue); 2749 } 2750 2751 if (!platform->pdata.low_power_mode) 2752 pm_runtime_put_sync_suspend(&client->dev); 2753 2754 anx7625_unregister_i2c_dummy_clients(platform); 2755 2756 if (platform->pdata.audio_en) 2757 anx7625_unregister_audio(platform); 2758 2759 return 0; 2760 } 2761 2762 static const struct i2c_device_id anx7625_id[] = { 2763 {"anx7625", 0}, 2764 {} 2765 }; 2766 2767 MODULE_DEVICE_TABLE(i2c, anx7625_id); 2768 2769 static const struct of_device_id anx_match_table[] = { 2770 {.compatible = "analogix,anx7625",}, 2771 {}, 2772 }; 2773 MODULE_DEVICE_TABLE(of, anx_match_table); 2774 2775 static struct i2c_driver anx7625_driver = { 2776 .driver = { 2777 .name = "anx7625", 2778 .of_match_table = anx_match_table, 2779 .pm = &anx7625_pm_ops, 2780 }, 2781 .probe = anx7625_i2c_probe, 2782 .remove = anx7625_i2c_remove, 2783 2784 .id_table = anx7625_id, 2785 }; 2786 2787 module_i2c_driver(anx7625_driver); 2788 2789 MODULE_DESCRIPTION("MIPI2DP anx7625 driver"); 2790 MODULE_AUTHOR("Xin Ji <xji@analogixsemi.com>"); 2791 MODULE_LICENSE("GPL v2"); 2792 MODULE_VERSION(ANX7625_DRV_VERSION); 2793