1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright(c) 2020, Analogix Semiconductor. All rights reserved. 4 * 5 */ 6 #include <linux/gcd.h> 7 #include <linux/gpio/consumer.h> 8 #include <linux/i2c.h> 9 #include <linux/interrupt.h> 10 #include <linux/iopoll.h> 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/mutex.h> 14 #include <linux/pm_runtime.h> 15 #include <linux/regulator/consumer.h> 16 #include <linux/slab.h> 17 #include <linux/types.h> 18 #include <linux/workqueue.h> 19 20 #include <linux/of_graph.h> 21 #include <linux/of_platform.h> 22 23 #include <drm/display/drm_dp_aux_bus.h> 24 #include <drm/display/drm_dp_helper.h> 25 #include <drm/display/drm_hdcp_helper.h> 26 #include <drm/drm_atomic_helper.h> 27 #include <drm/drm_bridge.h> 28 #include <drm/drm_edid.h> 29 #include <drm/drm_mipi_dsi.h> 30 #include <drm/drm_of.h> 31 #include <drm/drm_panel.h> 32 #include <drm/drm_print.h> 33 #include <drm/drm_probe_helper.h> 34 35 #include <media/v4l2-fwnode.h> 36 #include <sound/hdmi-codec.h> 37 #include <video/display_timing.h> 38 39 #include "anx7625.h" 40 41 /* 42 * There is a sync issue while access I2C register between AP(CPU) and 43 * internal firmware(OCM), to avoid the race condition, AP should access 44 * the reserved slave address before slave address occurs changes. 45 */ 46 static int i2c_access_workaround(struct anx7625_data *ctx, 47 struct i2c_client *client) 48 { 49 u8 offset; 50 struct device *dev = &client->dev; 51 int ret; 52 53 if (client == ctx->last_client) 54 return 0; 55 56 ctx->last_client = client; 57 58 if (client == ctx->i2c.tcpc_client) 59 offset = RSVD_00_ADDR; 60 else if (client == ctx->i2c.tx_p0_client) 61 offset = RSVD_D1_ADDR; 62 else if (client == ctx->i2c.tx_p1_client) 63 offset = RSVD_60_ADDR; 64 else if (client == ctx->i2c.rx_p0_client) 65 offset = RSVD_39_ADDR; 66 else if (client == ctx->i2c.rx_p1_client) 67 offset = RSVD_7F_ADDR; 68 else 69 offset = RSVD_00_ADDR; 70 71 ret = i2c_smbus_write_byte_data(client, offset, 0x00); 72 if (ret < 0) 73 DRM_DEV_ERROR(dev, 74 "fail to access i2c id=%x\n:%x", 75 client->addr, offset); 76 77 return ret; 78 } 79 80 static int anx7625_reg_read(struct anx7625_data *ctx, 81 struct i2c_client *client, u8 reg_addr) 82 { 83 int ret; 84 struct device *dev = &client->dev; 85 86 i2c_access_workaround(ctx, client); 87 88 ret = i2c_smbus_read_byte_data(client, reg_addr); 89 if (ret < 0) 90 DRM_DEV_ERROR(dev, "read i2c fail id=%x:%x\n", 91 client->addr, reg_addr); 92 93 return ret; 94 } 95 96 static int anx7625_reg_block_read(struct anx7625_data *ctx, 97 struct i2c_client *client, 98 u8 reg_addr, u8 len, u8 *buf) 99 { 100 int ret; 101 struct device *dev = &client->dev; 102 103 i2c_access_workaround(ctx, client); 104 105 ret = i2c_smbus_read_i2c_block_data(client, reg_addr, len, buf); 106 if (ret < 0) 107 DRM_DEV_ERROR(dev, "read i2c block fail id=%x:%x\n", 108 client->addr, reg_addr); 109 110 return ret; 111 } 112 113 static int anx7625_reg_write(struct anx7625_data *ctx, 114 struct i2c_client *client, 115 u8 reg_addr, u8 reg_val) 116 { 117 int ret; 118 struct device *dev = &client->dev; 119 120 i2c_access_workaround(ctx, client); 121 122 ret = i2c_smbus_write_byte_data(client, reg_addr, reg_val); 123 124 if (ret < 0) 125 DRM_DEV_ERROR(dev, "fail to write i2c id=%x\n:%x", 126 client->addr, reg_addr); 127 128 return ret; 129 } 130 131 static int anx7625_reg_block_write(struct anx7625_data *ctx, 132 struct i2c_client *client, 133 u8 reg_addr, u8 len, u8 *buf) 134 { 135 int ret; 136 struct device *dev = &client->dev; 137 138 i2c_access_workaround(ctx, client); 139 140 ret = i2c_smbus_write_i2c_block_data(client, reg_addr, len, buf); 141 if (ret < 0) 142 dev_err(dev, "write i2c block failed id=%x\n:%x", 143 client->addr, reg_addr); 144 145 return ret; 146 } 147 148 static int anx7625_write_or(struct anx7625_data *ctx, 149 struct i2c_client *client, 150 u8 offset, u8 mask) 151 { 152 int val; 153 154 val = anx7625_reg_read(ctx, client, offset); 155 if (val < 0) 156 return val; 157 158 return anx7625_reg_write(ctx, client, offset, (val | (mask))); 159 } 160 161 static int anx7625_write_and(struct anx7625_data *ctx, 162 struct i2c_client *client, 163 u8 offset, u8 mask) 164 { 165 int val; 166 167 val = anx7625_reg_read(ctx, client, offset); 168 if (val < 0) 169 return val; 170 171 return anx7625_reg_write(ctx, client, offset, (val & (mask))); 172 } 173 174 static int anx7625_write_and_or(struct anx7625_data *ctx, 175 struct i2c_client *client, 176 u8 offset, u8 and_mask, u8 or_mask) 177 { 178 int val; 179 180 val = anx7625_reg_read(ctx, client, offset); 181 if (val < 0) 182 return val; 183 184 return anx7625_reg_write(ctx, client, 185 offset, (val & and_mask) | (or_mask)); 186 } 187 188 static int anx7625_config_bit_matrix(struct anx7625_data *ctx) 189 { 190 int i, ret; 191 192 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 193 AUDIO_CONTROL_REGISTER, 0x80); 194 for (i = 0; i < 13; i++) 195 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 196 VIDEO_BIT_MATRIX_12 + i, 197 0x18 + i); 198 199 return ret; 200 } 201 202 static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) 203 { 204 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_CTRL_STATUS); 205 } 206 207 static int wait_aux_op_finish(struct anx7625_data *ctx) 208 { 209 struct device *dev = ctx->dev; 210 int val; 211 int ret; 212 213 ret = readx_poll_timeout(anx7625_read_ctrl_status_p0, 214 ctx, val, 215 (!(val & AP_AUX_CTRL_OP_EN) || (val < 0)), 216 2000, 217 2000 * 150); 218 if (ret) { 219 DRM_DEV_ERROR(dev, "aux operation fail!\n"); 220 return -EIO; 221 } 222 223 val = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 224 AP_AUX_CTRL_STATUS); 225 if (val < 0 || (val & 0x0F)) { 226 DRM_DEV_ERROR(dev, "aux status %02x\n", val); 227 return -EIO; 228 } 229 230 return 0; 231 } 232 233 static int anx7625_aux_trans(struct anx7625_data *ctx, u8 op, u32 address, 234 u8 len, u8 *buf) 235 { 236 struct device *dev = ctx->dev; 237 int ret; 238 u8 addrh, addrm, addrl; 239 u8 cmd; 240 bool is_write = !(op & DP_AUX_I2C_READ); 241 242 if (len > DP_AUX_MAX_PAYLOAD_BYTES) { 243 dev_err(dev, "exceed aux buffer len.\n"); 244 return -EINVAL; 245 } 246 247 if (!len) 248 return len; 249 250 addrl = address & 0xFF; 251 addrm = (address >> 8) & 0xFF; 252 addrh = (address >> 16) & 0xFF; 253 254 if (!is_write) 255 op &= ~DP_AUX_I2C_MOT; 256 cmd = DPCD_CMD(len, op); 257 258 /* Set command and length */ 259 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 260 AP_AUX_COMMAND, cmd); 261 262 /* Set aux access address */ 263 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 264 AP_AUX_ADDR_7_0, addrl); 265 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 266 AP_AUX_ADDR_15_8, addrm); 267 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 268 AP_AUX_ADDR_19_16, addrh); 269 270 if (is_write) 271 ret |= anx7625_reg_block_write(ctx, ctx->i2c.rx_p0_client, 272 AP_AUX_BUFF_START, len, buf); 273 /* Enable aux access */ 274 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 275 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 276 277 if (ret < 0) { 278 dev_err(dev, "cannot access aux related register.\n"); 279 return -EIO; 280 } 281 282 ret = wait_aux_op_finish(ctx); 283 if (ret < 0) { 284 dev_err(dev, "aux IO error: wait aux op finish.\n"); 285 return ret; 286 } 287 288 /* Write done */ 289 if (is_write) 290 return len; 291 292 /* Read done, read out dpcd data */ 293 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 294 AP_AUX_BUFF_START, len, buf); 295 if (ret < 0) { 296 dev_err(dev, "read dpcd register failed\n"); 297 return -EIO; 298 } 299 300 return len; 301 } 302 303 static int anx7625_video_mute_control(struct anx7625_data *ctx, 304 u8 status) 305 { 306 int ret; 307 308 if (status) { 309 /* Set mute on flag */ 310 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 311 AP_AV_STATUS, AP_MIPI_MUTE); 312 /* Clear mipi RX en */ 313 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 314 AP_AV_STATUS, (u8)~AP_MIPI_RX_EN); 315 } else { 316 /* Mute off flag */ 317 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 318 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 319 /* Set MIPI RX EN */ 320 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 321 AP_AV_STATUS, AP_MIPI_RX_EN); 322 } 323 324 return ret; 325 } 326 327 /* Reduction of fraction a/b */ 328 static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) 329 { 330 unsigned long gcd_num; 331 unsigned long tmp_a, tmp_b; 332 u32 i = 1; 333 334 gcd_num = gcd(*a, *b); 335 *a /= gcd_num; 336 *b /= gcd_num; 337 338 tmp_a = *a; 339 tmp_b = *b; 340 341 while ((*a > MAX_UNSIGNED_24BIT) || (*b > MAX_UNSIGNED_24BIT)) { 342 i++; 343 *a = tmp_a / i; 344 *b = tmp_b / i; 345 } 346 347 /* 348 * In the end, make a, b larger to have higher ODFC PLL 349 * output frequency accuracy 350 */ 351 while ((*a < MAX_UNSIGNED_24BIT) && (*b < MAX_UNSIGNED_24BIT)) { 352 *a <<= 1; 353 *b <<= 1; 354 } 355 356 *a >>= 1; 357 *b >>= 1; 358 } 359 360 static int anx7625_calculate_m_n(u32 pixelclock, 361 unsigned long *m, 362 unsigned long *n, 363 u8 *post_divider) 364 { 365 if (pixelclock > PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN) { 366 /* Pixel clock frequency is too high */ 367 DRM_ERROR("pixelclock too high, act(%d), maximum(%lu)\n", 368 pixelclock, 369 PLL_OUT_FREQ_ABS_MAX / POST_DIVIDER_MIN); 370 return -EINVAL; 371 } 372 373 if (pixelclock < PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX) { 374 /* Pixel clock frequency is too low */ 375 DRM_ERROR("pixelclock too low, act(%d), maximum(%lu)\n", 376 pixelclock, 377 PLL_OUT_FREQ_ABS_MIN / POST_DIVIDER_MAX); 378 return -EINVAL; 379 } 380 381 for (*post_divider = 1; 382 pixelclock < (PLL_OUT_FREQ_MIN / (*post_divider));) 383 *post_divider += 1; 384 385 if (*post_divider > POST_DIVIDER_MAX) { 386 for (*post_divider = 1; 387 (pixelclock < 388 (PLL_OUT_FREQ_ABS_MIN / (*post_divider)));) 389 *post_divider += 1; 390 391 if (*post_divider > POST_DIVIDER_MAX) { 392 DRM_ERROR("cannot find property post_divider(%d)\n", 393 *post_divider); 394 return -EDOM; 395 } 396 } 397 398 /* Patch to improve the accuracy */ 399 if (*post_divider == 7) { 400 /* 27,000,000 is not divisible by 7 */ 401 *post_divider = 8; 402 } else if (*post_divider == 11) { 403 /* 27,000,000 is not divisible by 11 */ 404 *post_divider = 12; 405 } else if ((*post_divider == 13) || (*post_divider == 14)) { 406 /* 27,000,000 is not divisible by 13 or 14 */ 407 *post_divider = 15; 408 } 409 410 if (pixelclock * (*post_divider) > PLL_OUT_FREQ_ABS_MAX) { 411 DRM_ERROR("act clock(%u) large than maximum(%lu)\n", 412 pixelclock * (*post_divider), 413 PLL_OUT_FREQ_ABS_MAX); 414 return -EDOM; 415 } 416 417 *m = pixelclock; 418 *n = XTAL_FRQ / (*post_divider); 419 420 anx7625_reduction_of_a_fraction(m, n); 421 422 return 0; 423 } 424 425 static int anx7625_odfc_config(struct anx7625_data *ctx, 426 u8 post_divider) 427 { 428 int ret; 429 struct device *dev = ctx->dev; 430 431 /* Config input reference clock frequency 27MHz/19.2MHz */ 432 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 433 ~(REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 434 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_16, 435 (REF_CLK_27000KHZ << MIPI_FREF_D_IND)); 436 /* Post divider */ 437 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 438 MIPI_DIGITAL_PLL_8, 0x0f); 439 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_8, 440 post_divider << 4); 441 442 /* Add patch for MIS2-125 (5pcs ANX7625 fail ATE MBIST test) */ 443 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 444 ~MIPI_PLL_VCO_TUNE_REG_VAL); 445 446 /* Reset ODFC PLL */ 447 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 448 ~MIPI_PLL_RESET_N); 449 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_7, 450 MIPI_PLL_RESET_N); 451 452 if (ret < 0) 453 DRM_DEV_ERROR(dev, "IO error.\n"); 454 455 return ret; 456 } 457 458 /* 459 * The MIPI source video data exist large variation (e.g. 59Hz ~ 61Hz), 460 * anx7625 defined K ratio for matching MIPI input video clock and 461 * DP output video clock. Increase K value can match bigger video data 462 * variation. IVO panel has small variation than DP CTS spec, need 463 * decrease the K value. 464 */ 465 static int anx7625_set_k_value(struct anx7625_data *ctx) 466 { 467 struct edid *edid = (struct edid *)ctx->slimport_edid_p.edid_raw_data; 468 469 if (edid->mfg_id[0] == IVO_MID0 && edid->mfg_id[1] == IVO_MID1) 470 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 471 MIPI_DIGITAL_ADJ_1, 0x3B); 472 473 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 474 MIPI_DIGITAL_ADJ_1, 0x3D); 475 } 476 477 static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) 478 { 479 struct device *dev = ctx->dev; 480 unsigned long m, n; 481 u16 htotal; 482 int ret; 483 u8 post_divider = 0; 484 485 ret = anx7625_calculate_m_n(ctx->dt.pixelclock.min * 1000, 486 &m, &n, &post_divider); 487 488 if (ret) { 489 DRM_DEV_ERROR(dev, "cannot get property m n value.\n"); 490 return ret; 491 } 492 493 DRM_DEV_DEBUG_DRIVER(dev, "compute M(%lu), N(%lu), divider(%d).\n", 494 m, n, post_divider); 495 496 /* Configure pixel clock */ 497 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_L, 498 (ctx->dt.pixelclock.min / 1000) & 0xFF); 499 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, PIXEL_CLOCK_H, 500 (ctx->dt.pixelclock.min / 1000) >> 8); 501 /* Lane count */ 502 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 503 MIPI_LANE_CTRL_0, 0xfc); 504 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 505 MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); 506 507 /* Htotal */ 508 htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + 509 ctx->dt.hback_porch.min + ctx->dt.hsync_len.min; 510 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 511 HORIZONTAL_TOTAL_PIXELS_L, htotal & 0xFF); 512 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 513 HORIZONTAL_TOTAL_PIXELS_H, htotal >> 8); 514 /* Hactive */ 515 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 516 HORIZONTAL_ACTIVE_PIXELS_L, ctx->dt.hactive.min & 0xFF); 517 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 518 HORIZONTAL_ACTIVE_PIXELS_H, ctx->dt.hactive.min >> 8); 519 /* HFP */ 520 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 521 HORIZONTAL_FRONT_PORCH_L, ctx->dt.hfront_porch.min); 522 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 523 HORIZONTAL_FRONT_PORCH_H, 524 ctx->dt.hfront_porch.min >> 8); 525 /* HWS */ 526 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 527 HORIZONTAL_SYNC_WIDTH_L, ctx->dt.hsync_len.min); 528 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 529 HORIZONTAL_SYNC_WIDTH_H, ctx->dt.hsync_len.min >> 8); 530 /* HBP */ 531 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 532 HORIZONTAL_BACK_PORCH_L, ctx->dt.hback_porch.min); 533 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 534 HORIZONTAL_BACK_PORCH_H, ctx->dt.hback_porch.min >> 8); 535 /* Vactive */ 536 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_L, 537 ctx->dt.vactive.min); 538 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, ACTIVE_LINES_H, 539 ctx->dt.vactive.min >> 8); 540 /* VFP */ 541 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 542 VERTICAL_FRONT_PORCH, ctx->dt.vfront_porch.min); 543 /* VWS */ 544 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 545 VERTICAL_SYNC_WIDTH, ctx->dt.vsync_len.min); 546 /* VBP */ 547 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p2_client, 548 VERTICAL_BACK_PORCH, ctx->dt.vback_porch.min); 549 /* M value */ 550 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 551 MIPI_PLL_M_NUM_23_16, (m >> 16) & 0xff); 552 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 553 MIPI_PLL_M_NUM_15_8, (m >> 8) & 0xff); 554 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 555 MIPI_PLL_M_NUM_7_0, (m & 0xff)); 556 /* N value */ 557 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 558 MIPI_PLL_N_NUM_23_16, (n >> 16) & 0xff); 559 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 560 MIPI_PLL_N_NUM_15_8, (n >> 8) & 0xff); 561 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_PLL_N_NUM_7_0, 562 (n & 0xff)); 563 564 anx7625_set_k_value(ctx); 565 566 ret |= anx7625_odfc_config(ctx, post_divider - 1); 567 568 if (ret < 0) 569 DRM_DEV_ERROR(dev, "mipi dsi setup IO error.\n"); 570 571 return ret; 572 } 573 574 static int anx7625_swap_dsi_lane3(struct anx7625_data *ctx) 575 { 576 int val; 577 struct device *dev = ctx->dev; 578 579 /* Swap MIPI-DSI data lane 3 P and N */ 580 val = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP); 581 if (val < 0) { 582 DRM_DEV_ERROR(dev, "IO error : access MIPI_SWAP.\n"); 583 return -EIO; 584 } 585 586 val |= (1 << MIPI_SWAP_CH3); 587 return anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, MIPI_SWAP, val); 588 } 589 590 static int anx7625_api_dsi_config(struct anx7625_data *ctx) 591 592 { 593 int val, ret; 594 struct device *dev = ctx->dev; 595 596 /* Swap MIPI-DSI data lane 3 P and N */ 597 ret = anx7625_swap_dsi_lane3(ctx); 598 if (ret < 0) { 599 DRM_DEV_ERROR(dev, "IO error : swap dsi lane 3 fail.\n"); 600 return ret; 601 } 602 603 /* DSI clock settings */ 604 val = (0 << MIPI_HS_PWD_CLK) | 605 (0 << MIPI_HS_RT_CLK) | 606 (0 << MIPI_PD_CLK) | 607 (1 << MIPI_CLK_RT_MANUAL_PD_EN) | 608 (1 << MIPI_CLK_HS_MANUAL_PD_EN) | 609 (0 << MIPI_CLK_DET_DET_BYPASS) | 610 (0 << MIPI_CLK_MISS_CTRL) | 611 (0 << MIPI_PD_LPTX_CH_MANUAL_PD_EN); 612 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 613 MIPI_PHY_CONTROL_3, val); 614 615 /* 616 * Decreased HS prepare timing delay from 160ns to 80ns work with 617 * a) Dragon board 810 series (Qualcomm AP) 618 * b) Moving Pixel DSI source (PG3A pattern generator + 619 * P332 D-PHY Probe) default D-PHY timing 620 * 5ns/step 621 */ 622 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 623 MIPI_TIME_HS_PRPR, 0x10); 624 625 /* Enable DSI mode*/ 626 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_18, 627 SELECT_DSI << MIPI_DPI_SELECT); 628 629 ret |= anx7625_dsi_video_timing_config(ctx); 630 if (ret < 0) { 631 DRM_DEV_ERROR(dev, "dsi video timing config fail\n"); 632 return ret; 633 } 634 635 /* Toggle m, n ready */ 636 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 637 ~(MIPI_M_NUM_READY | MIPI_N_NUM_READY)); 638 usleep_range(1000, 1100); 639 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, MIPI_DIGITAL_PLL_6, 640 MIPI_M_NUM_READY | MIPI_N_NUM_READY); 641 642 /* Configure integer stable register */ 643 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 644 MIPI_VIDEO_STABLE_CNT, 0x02); 645 /* Power on MIPI RX */ 646 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 647 MIPI_LANE_CTRL_10, 0x00); 648 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 649 MIPI_LANE_CTRL_10, 0x80); 650 651 if (ret < 0) 652 DRM_DEV_ERROR(dev, "IO error : mipi dsi enable init fail.\n"); 653 654 return ret; 655 } 656 657 static int anx7625_dsi_config(struct anx7625_data *ctx) 658 { 659 struct device *dev = ctx->dev; 660 int ret; 661 662 DRM_DEV_DEBUG_DRIVER(dev, "config dsi.\n"); 663 664 /* DSC disable */ 665 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 666 R_DSC_CTRL_0, ~DSC_EN); 667 668 ret |= anx7625_api_dsi_config(ctx); 669 670 if (ret < 0) { 671 DRM_DEV_ERROR(dev, "IO error : api dsi config error.\n"); 672 return ret; 673 } 674 675 /* Set MIPI RX EN */ 676 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 677 AP_AV_STATUS, AP_MIPI_RX_EN); 678 /* Clear mute flag */ 679 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 680 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 681 if (ret < 0) 682 DRM_DEV_ERROR(dev, "IO error : enable mipi rx fail.\n"); 683 else 684 DRM_DEV_DEBUG_DRIVER(dev, "success to config DSI\n"); 685 686 return ret; 687 } 688 689 static int anx7625_api_dpi_config(struct anx7625_data *ctx) 690 { 691 struct device *dev = ctx->dev; 692 u16 freq = ctx->dt.pixelclock.min / 1000; 693 int ret; 694 695 /* configure pixel clock */ 696 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 697 PIXEL_CLOCK_L, freq & 0xFF); 698 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 699 PIXEL_CLOCK_H, (freq >> 8)); 700 701 /* set DPI mode */ 702 /* set to DPI PLL module sel */ 703 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 704 MIPI_DIGITAL_PLL_9, 0x20); 705 /* power down MIPI */ 706 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 707 MIPI_LANE_CTRL_10, 0x08); 708 /* enable DPI mode */ 709 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, 710 MIPI_DIGITAL_PLL_18, 0x1C); 711 /* set first edge */ 712 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 713 VIDEO_CONTROL_0, 0x06); 714 if (ret < 0) 715 DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); 716 717 return ret; 718 } 719 720 static int anx7625_dpi_config(struct anx7625_data *ctx) 721 { 722 struct device *dev = ctx->dev; 723 int ret; 724 725 DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); 726 727 /* DSC disable */ 728 ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 729 R_DSC_CTRL_0, ~DSC_EN); 730 if (ret < 0) { 731 DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); 732 return ret; 733 } 734 735 ret = anx7625_config_bit_matrix(ctx); 736 if (ret < 0) { 737 DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); 738 return ret; 739 } 740 741 ret = anx7625_api_dpi_config(ctx); 742 if (ret < 0) { 743 DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); 744 return ret; 745 } 746 747 /* set MIPI RX EN */ 748 ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 749 AP_AV_STATUS, AP_MIPI_RX_EN); 750 /* clear mute flag */ 751 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 752 AP_AV_STATUS, (u8)~AP_MIPI_MUTE); 753 if (ret < 0) 754 DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); 755 756 return ret; 757 } 758 759 static int anx7625_read_flash_status(struct anx7625_data *ctx) 760 { 761 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, R_RAM_CTRL); 762 } 763 764 static int anx7625_hdcp_key_probe(struct anx7625_data *ctx) 765 { 766 int ret, val; 767 struct device *dev = ctx->dev; 768 u8 ident[FLASH_BUF_LEN]; 769 770 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 771 FLASH_ADDR_HIGH, 0x91); 772 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 773 FLASH_ADDR_LOW, 0xA0); 774 if (ret < 0) { 775 dev_err(dev, "IO error : set key flash address.\n"); 776 return ret; 777 } 778 779 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 780 FLASH_LEN_HIGH, (FLASH_BUF_LEN - 1) >> 8); 781 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 782 FLASH_LEN_LOW, (FLASH_BUF_LEN - 1) & 0xFF); 783 if (ret < 0) { 784 dev_err(dev, "IO error : set key flash len.\n"); 785 return ret; 786 } 787 788 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 789 R_FLASH_RW_CTRL, FLASH_READ); 790 ret |= readx_poll_timeout(anx7625_read_flash_status, 791 ctx, val, 792 ((val & FLASH_DONE) || (val < 0)), 793 2000, 794 2000 * 150); 795 if (ret) { 796 dev_err(dev, "flash read access fail!\n"); 797 return -EIO; 798 } 799 800 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 801 FLASH_BUF_BASE_ADDR, 802 FLASH_BUF_LEN, ident); 803 if (ret < 0) { 804 dev_err(dev, "read flash data fail!\n"); 805 return -EIO; 806 } 807 808 if (ident[29] == 0xFF && ident[30] == 0xFF && ident[31] == 0xFF) 809 return -EINVAL; 810 811 return 0; 812 } 813 814 static int anx7625_hdcp_key_load(struct anx7625_data *ctx) 815 { 816 int ret; 817 struct device *dev = ctx->dev; 818 819 /* Select HDCP 1.4 KEY */ 820 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 821 R_BOOT_RETRY, 0x12); 822 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 823 FLASH_ADDR_HIGH, HDCP14KEY_START_ADDR >> 8); 824 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 825 FLASH_ADDR_LOW, HDCP14KEY_START_ADDR & 0xFF); 826 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 827 R_RAM_LEN_H, HDCP14KEY_SIZE >> 12); 828 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 829 R_RAM_LEN_L, HDCP14KEY_SIZE >> 4); 830 831 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 832 R_RAM_ADDR_H, 0); 833 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 834 R_RAM_ADDR_L, 0); 835 /* Enable HDCP 1.4 KEY load */ 836 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 837 R_RAM_CTRL, DECRYPT_EN | LOAD_START); 838 dev_dbg(dev, "load HDCP 1.4 key done\n"); 839 return ret; 840 } 841 842 static int anx7625_hdcp_disable(struct anx7625_data *ctx) 843 { 844 int ret; 845 struct device *dev = ctx->dev; 846 847 dev_dbg(dev, "disable HDCP 1.4\n"); 848 849 /* Disable HDCP */ 850 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 851 /* Try auth flag */ 852 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 853 /* Interrupt for DRM */ 854 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 855 if (ret < 0) 856 dev_err(dev, "fail to disable HDCP\n"); 857 858 return anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 859 TX_HDCP_CTRL0, ~HARD_AUTH_EN & 0xFF); 860 } 861 862 static int anx7625_hdcp_enable(struct anx7625_data *ctx) 863 { 864 u8 bcap; 865 int ret; 866 struct device *dev = ctx->dev; 867 868 ret = anx7625_hdcp_key_probe(ctx); 869 if (ret) { 870 dev_dbg(dev, "no key found, not to do hdcp\n"); 871 return ret; 872 } 873 874 /* Read downstream capability */ 875 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_READ, DP_AUX_HDCP_BCAPS, 1, &bcap); 876 if (ret < 0) 877 return ret; 878 879 if (!(bcap & DP_BCAPS_HDCP_CAPABLE)) { 880 pr_warn("downstream not support HDCP 1.4, cap(%x).\n", bcap); 881 return 0; 882 } 883 884 dev_dbg(dev, "enable HDCP 1.4\n"); 885 886 /* First clear HDCP state */ 887 ret = anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 888 TX_HDCP_CTRL0, 889 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 890 usleep_range(1000, 1100); 891 /* Second clear HDCP state */ 892 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 893 TX_HDCP_CTRL0, 894 KSVLIST_VLD | BKSV_SRM_PASS | RE_AUTHEN); 895 896 /* Set time for waiting KSVR */ 897 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 898 SP_TX_WAIT_KSVR_TIME, 0xc8); 899 /* Set time for waiting R0 */ 900 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p0_client, 901 SP_TX_WAIT_R0_TIME, 0xb0); 902 ret |= anx7625_hdcp_key_load(ctx); 903 if (ret) { 904 pr_warn("prepare HDCP key failed.\n"); 905 return ret; 906 } 907 908 ret = anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20); 909 910 /* Try auth flag */ 911 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 912 /* Interrupt for DRM */ 913 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 914 if (ret < 0) 915 dev_err(dev, "fail to enable HDCP\n"); 916 917 return anx7625_write_or(ctx, ctx->i2c.tx_p0_client, 918 TX_HDCP_CTRL0, HARD_AUTH_EN); 919 } 920 921 static void anx7625_dp_start(struct anx7625_data *ctx) 922 { 923 int ret; 924 struct device *dev = ctx->dev; 925 u8 data; 926 927 if (!ctx->display_timing_valid) { 928 DRM_DEV_ERROR(dev, "mipi not set display timing yet.\n"); 929 return; 930 } 931 932 dev_dbg(dev, "set downstream sink into normal\n"); 933 /* Downstream sink enter into normal mode */ 934 data = DP_SET_POWER_D0; 935 ret = anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, DP_SET_POWER, 1, &data); 936 if (ret < 0) 937 dev_err(dev, "IO error : set sink into normal mode fail\n"); 938 939 /* Disable HDCP */ 940 anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 941 942 if (ctx->pdata.is_dpi) 943 ret = anx7625_dpi_config(ctx); 944 else 945 ret = anx7625_dsi_config(ctx); 946 947 if (ret < 0) 948 DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); 949 950 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 951 952 ctx->dp_en = 1; 953 } 954 955 static void anx7625_dp_stop(struct anx7625_data *ctx) 956 { 957 struct device *dev = ctx->dev; 958 int ret; 959 u8 data; 960 961 DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n"); 962 963 /* 964 * Video disable: 0x72:08 bit 7 = 0; 965 * Audio disable: 0x70:87 bit 0 = 0; 966 */ 967 ret = anx7625_write_and(ctx, ctx->i2c.tx_p0_client, 0x87, 0xfe); 968 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f); 969 970 ret |= anx7625_video_mute_control(ctx, 1); 971 972 dev_dbg(dev, "notify downstream enter into standby\n"); 973 /* Downstream monitor enter into standby mode */ 974 data = DP_SET_POWER_D3; 975 ret |= anx7625_aux_trans(ctx, DP_AUX_NATIVE_WRITE, DP_SET_POWER, 1, &data); 976 if (ret < 0) 977 DRM_DEV_ERROR(dev, "IO error : mute video fail\n"); 978 979 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 980 981 ctx->dp_en = 0; 982 } 983 984 static int sp_tx_rst_aux(struct anx7625_data *ctx) 985 { 986 int ret; 987 988 ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 989 AUX_RST); 990 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, RST_CTRL2, 991 ~AUX_RST); 992 return ret; 993 } 994 995 static int sp_tx_aux_wr(struct anx7625_data *ctx, u8 offset) 996 { 997 int ret; 998 999 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1000 AP_AUX_BUFF_START, offset); 1001 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1002 AP_AUX_COMMAND, 0x04); 1003 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1004 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1005 return (ret | wait_aux_op_finish(ctx)); 1006 } 1007 1008 static int sp_tx_aux_rd(struct anx7625_data *ctx, u8 len_cmd) 1009 { 1010 int ret; 1011 1012 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1013 AP_AUX_COMMAND, len_cmd); 1014 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1015 AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); 1016 return (ret | wait_aux_op_finish(ctx)); 1017 } 1018 1019 static int sp_tx_get_edid_block(struct anx7625_data *ctx) 1020 { 1021 int c = 0; 1022 struct device *dev = ctx->dev; 1023 1024 sp_tx_aux_wr(ctx, 0x7e); 1025 sp_tx_aux_rd(ctx, 0x01); 1026 c = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, AP_AUX_BUFF_START); 1027 if (c < 0) { 1028 DRM_DEV_ERROR(dev, "IO error : access AUX BUFF.\n"); 1029 return -EIO; 1030 } 1031 1032 DRM_DEV_DEBUG_DRIVER(dev, " EDID Block = %d\n", c + 1); 1033 1034 if (c > MAX_EDID_BLOCK) 1035 c = 1; 1036 1037 return c; 1038 } 1039 1040 static int edid_read(struct anx7625_data *ctx, 1041 u8 offset, u8 *pblock_buf) 1042 { 1043 int ret, cnt; 1044 struct device *dev = ctx->dev; 1045 1046 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1047 sp_tx_aux_wr(ctx, offset); 1048 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1049 ret = sp_tx_aux_rd(ctx, 0xf1); 1050 1051 if (ret) { 1052 ret = sp_tx_rst_aux(ctx); 1053 DRM_DEV_DEBUG_DRIVER(dev, "edid read fail, reset!\n"); 1054 } else { 1055 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1056 AP_AUX_BUFF_START, 1057 MAX_DPCD_BUFFER_SIZE, 1058 pblock_buf); 1059 if (ret > 0) 1060 break; 1061 } 1062 } 1063 1064 if (cnt > EDID_TRY_CNT) 1065 return -EIO; 1066 1067 return ret; 1068 } 1069 1070 static int segments_edid_read(struct anx7625_data *ctx, 1071 u8 segment, u8 *buf, u8 offset) 1072 { 1073 u8 cnt; 1074 int ret; 1075 struct device *dev = ctx->dev; 1076 1077 /* Write address only */ 1078 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1079 AP_AUX_ADDR_7_0, 0x30); 1080 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1081 AP_AUX_COMMAND, 0x04); 1082 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1083 AP_AUX_CTRL_STATUS, 1084 AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN); 1085 1086 ret |= wait_aux_op_finish(ctx); 1087 /* Write segment address */ 1088 ret |= sp_tx_aux_wr(ctx, segment); 1089 /* Data read */ 1090 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1091 AP_AUX_ADDR_7_0, 0x50); 1092 if (ret) { 1093 DRM_DEV_ERROR(dev, "IO error : aux initial fail.\n"); 1094 return ret; 1095 } 1096 1097 for (cnt = 0; cnt <= EDID_TRY_CNT; cnt++) { 1098 sp_tx_aux_wr(ctx, offset); 1099 /* Set I2C read com 0x01 mot = 0 and read 16 bytes */ 1100 ret = sp_tx_aux_rd(ctx, 0xf1); 1101 1102 if (ret) { 1103 ret = sp_tx_rst_aux(ctx); 1104 DRM_DEV_ERROR(dev, "segment read fail, reset!\n"); 1105 } else { 1106 ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, 1107 AP_AUX_BUFF_START, 1108 MAX_DPCD_BUFFER_SIZE, buf); 1109 if (ret > 0) 1110 break; 1111 } 1112 } 1113 1114 if (cnt > EDID_TRY_CNT) 1115 return -EIO; 1116 1117 return ret; 1118 } 1119 1120 static int sp_tx_edid_read(struct anx7625_data *ctx, 1121 u8 *pedid_blocks_buf) 1122 { 1123 u8 offset; 1124 int edid_pos; 1125 int count, blocks_num; 1126 u8 pblock_buf[MAX_DPCD_BUFFER_SIZE]; 1127 u8 i, j; 1128 int g_edid_break = 0; 1129 int ret; 1130 struct device *dev = ctx->dev; 1131 1132 /* Address initial */ 1133 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1134 AP_AUX_ADDR_7_0, 0x50); 1135 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1136 AP_AUX_ADDR_15_8, 0); 1137 ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, 1138 AP_AUX_ADDR_19_16, 0xf0); 1139 if (ret < 0) { 1140 DRM_DEV_ERROR(dev, "access aux channel IO error.\n"); 1141 return -EIO; 1142 } 1143 1144 blocks_num = sp_tx_get_edid_block(ctx); 1145 if (blocks_num < 0) 1146 return blocks_num; 1147 1148 count = 0; 1149 1150 do { 1151 switch (count) { 1152 case 0: 1153 case 1: 1154 for (i = 0; i < 8; i++) { 1155 offset = (i + count * 8) * MAX_DPCD_BUFFER_SIZE; 1156 g_edid_break = edid_read(ctx, offset, 1157 pblock_buf); 1158 1159 if (g_edid_break < 0) 1160 break; 1161 1162 memcpy(&pedid_blocks_buf[offset], 1163 pblock_buf, 1164 MAX_DPCD_BUFFER_SIZE); 1165 } 1166 1167 break; 1168 case 2: 1169 offset = 0x00; 1170 1171 for (j = 0; j < 8; j++) { 1172 edid_pos = (j + count * 8) * 1173 MAX_DPCD_BUFFER_SIZE; 1174 1175 if (g_edid_break == 1) 1176 break; 1177 1178 ret = segments_edid_read(ctx, count / 2, 1179 pblock_buf, offset); 1180 if (ret < 0) 1181 return ret; 1182 1183 memcpy(&pedid_blocks_buf[edid_pos], 1184 pblock_buf, 1185 MAX_DPCD_BUFFER_SIZE); 1186 offset = offset + 0x10; 1187 } 1188 1189 break; 1190 case 3: 1191 offset = 0x80; 1192 1193 for (j = 0; j < 8; j++) { 1194 edid_pos = (j + count * 8) * 1195 MAX_DPCD_BUFFER_SIZE; 1196 if (g_edid_break == 1) 1197 break; 1198 1199 ret = segments_edid_read(ctx, count / 2, 1200 pblock_buf, offset); 1201 if (ret < 0) 1202 return ret; 1203 1204 memcpy(&pedid_blocks_buf[edid_pos], 1205 pblock_buf, 1206 MAX_DPCD_BUFFER_SIZE); 1207 offset = offset + 0x10; 1208 } 1209 1210 break; 1211 default: 1212 break; 1213 } 1214 1215 count++; 1216 1217 } while (blocks_num >= count); 1218 1219 /* Check edid data */ 1220 if (!drm_edid_is_valid((struct edid *)pedid_blocks_buf)) { 1221 DRM_DEV_ERROR(dev, "WARNING! edid check fail!\n"); 1222 return -EINVAL; 1223 } 1224 1225 /* Reset aux channel */ 1226 ret = sp_tx_rst_aux(ctx); 1227 if (ret < 0) { 1228 DRM_DEV_ERROR(dev, "Failed to reset aux channel!\n"); 1229 return ret; 1230 } 1231 1232 return (blocks_num + 1); 1233 } 1234 1235 static void anx7625_power_on(struct anx7625_data *ctx) 1236 { 1237 struct device *dev = ctx->dev; 1238 int ret, i; 1239 1240 if (!ctx->pdata.low_power_mode) { 1241 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1242 return; 1243 } 1244 1245 for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) { 1246 ret = regulator_enable(ctx->pdata.supplies[i].consumer); 1247 if (ret < 0) { 1248 DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n", 1249 i, ret); 1250 goto reg_err; 1251 } 1252 usleep_range(2000, 2100); 1253 } 1254 1255 usleep_range(11000, 12000); 1256 1257 /* Power on pin enable */ 1258 gpiod_set_value(ctx->pdata.gpio_p_on, 1); 1259 usleep_range(10000, 11000); 1260 /* Power reset pin enable */ 1261 gpiod_set_value(ctx->pdata.gpio_reset, 1); 1262 usleep_range(10000, 11000); 1263 1264 DRM_DEV_DEBUG_DRIVER(dev, "power on !\n"); 1265 return; 1266 reg_err: 1267 for (--i; i >= 0; i--) 1268 regulator_disable(ctx->pdata.supplies[i].consumer); 1269 } 1270 1271 static void anx7625_power_standby(struct anx7625_data *ctx) 1272 { 1273 struct device *dev = ctx->dev; 1274 int ret; 1275 1276 if (!ctx->pdata.low_power_mode) { 1277 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); 1278 return; 1279 } 1280 1281 gpiod_set_value(ctx->pdata.gpio_reset, 0); 1282 usleep_range(1000, 1100); 1283 gpiod_set_value(ctx->pdata.gpio_p_on, 0); 1284 usleep_range(1000, 1100); 1285 1286 ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies), 1287 ctx->pdata.supplies); 1288 if (ret < 0) 1289 DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret); 1290 1291 DRM_DEV_DEBUG_DRIVER(dev, "power down\n"); 1292 } 1293 1294 /* Basic configurations of ANX7625 */ 1295 static void anx7625_config(struct anx7625_data *ctx) 1296 { 1297 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1298 XTAL_FRQ_SEL, XTAL_FRQ_27M); 1299 } 1300 1301 static void anx7625_disable_pd_protocol(struct anx7625_data *ctx) 1302 { 1303 struct device *dev = ctx->dev; 1304 int ret; 1305 1306 /* Reset main ocm */ 1307 ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x40); 1308 /* Disable PD */ 1309 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1310 AP_AV_STATUS, AP_DISABLE_PD); 1311 /* Release main ocm */ 1312 ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 0x88, 0x00); 1313 1314 if (ret < 0) 1315 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature fail.\n"); 1316 else 1317 DRM_DEV_DEBUG_DRIVER(dev, "disable PD feature succeeded.\n"); 1318 } 1319 1320 static int anx7625_ocm_loading_check(struct anx7625_data *ctx) 1321 { 1322 int ret; 1323 struct device *dev = ctx->dev; 1324 1325 /* Check interface workable */ 1326 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1327 FLASH_LOAD_STA); 1328 if (ret < 0) { 1329 DRM_DEV_ERROR(dev, "IO error : access flash load.\n"); 1330 return ret; 1331 } 1332 if ((ret & FLASH_LOAD_STA_CHK) != FLASH_LOAD_STA_CHK) 1333 return -ENODEV; 1334 1335 anx7625_disable_pd_protocol(ctx); 1336 1337 DRM_DEV_DEBUG_DRIVER(dev, "Firmware ver %02x%02x,", 1338 anx7625_reg_read(ctx, 1339 ctx->i2c.rx_p0_client, 1340 OCM_FW_VERSION), 1341 anx7625_reg_read(ctx, 1342 ctx->i2c.rx_p0_client, 1343 OCM_FW_REVERSION)); 1344 DRM_DEV_DEBUG_DRIVER(dev, "Driver version %s\n", 1345 ANX7625_DRV_VERSION); 1346 1347 return 0; 1348 } 1349 1350 static void anx7625_power_on_init(struct anx7625_data *ctx) 1351 { 1352 int retry_count, i; 1353 1354 for (retry_count = 0; retry_count < 3; retry_count++) { 1355 anx7625_power_on(ctx); 1356 anx7625_config(ctx); 1357 1358 for (i = 0; i < OCM_LOADING_TIME; i++) { 1359 if (!anx7625_ocm_loading_check(ctx)) 1360 return; 1361 usleep_range(1000, 1100); 1362 } 1363 anx7625_power_standby(ctx); 1364 } 1365 } 1366 1367 static void anx7625_init_gpio(struct anx7625_data *platform) 1368 { 1369 struct device *dev = platform->dev; 1370 1371 DRM_DEV_DEBUG_DRIVER(dev, "init gpio\n"); 1372 1373 /* Gpio for chip power enable */ 1374 platform->pdata.gpio_p_on = 1375 devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); 1376 if (IS_ERR_OR_NULL(platform->pdata.gpio_p_on)) { 1377 DRM_DEV_DEBUG_DRIVER(dev, "no enable gpio found\n"); 1378 platform->pdata.gpio_p_on = NULL; 1379 } 1380 1381 /* Gpio for chip reset */ 1382 platform->pdata.gpio_reset = 1383 devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); 1384 if (IS_ERR_OR_NULL(platform->pdata.gpio_reset)) { 1385 DRM_DEV_DEBUG_DRIVER(dev, "no reset gpio found\n"); 1386 platform->pdata.gpio_reset = NULL; 1387 } 1388 1389 if (platform->pdata.gpio_p_on && platform->pdata.gpio_reset) { 1390 platform->pdata.low_power_mode = 1; 1391 DRM_DEV_DEBUG_DRIVER(dev, "low power mode, pon %d, reset %d.\n", 1392 desc_to_gpio(platform->pdata.gpio_p_on), 1393 desc_to_gpio(platform->pdata.gpio_reset)); 1394 } else { 1395 platform->pdata.low_power_mode = 0; 1396 DRM_DEV_DEBUG_DRIVER(dev, "not low power mode.\n"); 1397 } 1398 } 1399 1400 static void anx7625_stop_dp_work(struct anx7625_data *ctx) 1401 { 1402 ctx->hpd_status = 0; 1403 ctx->hpd_high_cnt = 0; 1404 } 1405 1406 static void anx7625_start_dp_work(struct anx7625_data *ctx) 1407 { 1408 int ret; 1409 struct device *dev = ctx->dev; 1410 1411 if (ctx->hpd_high_cnt >= 2) { 1412 DRM_DEV_DEBUG_DRIVER(dev, "filter useless HPD\n"); 1413 return; 1414 } 1415 1416 ctx->hpd_status = 1; 1417 ctx->hpd_high_cnt++; 1418 1419 /* Not support HDCP */ 1420 ret = anx7625_write_and(ctx, ctx->i2c.rx_p1_client, 0xee, 0x9f); 1421 1422 /* Try auth flag */ 1423 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); 1424 /* Interrupt for DRM */ 1425 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); 1426 if (ret < 0) { 1427 DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); 1428 return; 1429 } 1430 1431 ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); 1432 if (ret < 0) 1433 return; 1434 1435 DRM_DEV_DEBUG_DRIVER(dev, "Secure OCM version=%02x\n", ret); 1436 } 1437 1438 static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx) 1439 { 1440 int ret; 1441 1442 /* Set irq detect window to 2ms */ 1443 ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 1444 HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF); 1445 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 1446 HPD_DET_TIMER_BIT8_15, 1447 (HPD_TIME >> 8) & 0xFF); 1448 ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, 1449 HPD_DET_TIMER_BIT16_23, 1450 (HPD_TIME >> 16) & 0xFF); 1451 if (ret < 0) 1452 return ret; 1453 1454 return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS); 1455 } 1456 1457 static int _anx7625_hpd_polling(struct anx7625_data *ctx, 1458 unsigned long wait_us) 1459 { 1460 int ret, val; 1461 struct device *dev = ctx->dev; 1462 1463 /* Interrupt mode, no need poll HPD status, just return */ 1464 if (ctx->pdata.intp_irq) 1465 return 0; 1466 1467 ret = readx_poll_timeout(anx7625_read_hpd_status_p0, 1468 ctx, val, 1469 ((val & HPD_STATUS) || (val < 0)), 1470 wait_us / 100, 1471 wait_us); 1472 if (ret) { 1473 DRM_DEV_ERROR(dev, "no hpd.\n"); 1474 return ret; 1475 } 1476 1477 DRM_DEV_DEBUG_DRIVER(dev, "system status: 0x%x. HPD raise up.\n", val); 1478 anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1479 INTR_ALERT_1, 0xFF); 1480 anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1481 INTERFACE_CHANGE_INT, 0); 1482 1483 anx7625_start_dp_work(ctx); 1484 1485 if (!ctx->pdata.panel_bridge && ctx->bridge_attached) 1486 drm_helper_hpd_irq_event(ctx->bridge.dev); 1487 1488 return 0; 1489 } 1490 1491 static int anx7625_wait_hpd_asserted(struct drm_dp_aux *aux, 1492 unsigned long wait_us) 1493 { 1494 struct anx7625_data *ctx = container_of(aux, struct anx7625_data, aux); 1495 struct device *dev = ctx->dev; 1496 int ret; 1497 1498 pm_runtime_get_sync(dev); 1499 ret = _anx7625_hpd_polling(ctx, wait_us); 1500 pm_runtime_mark_last_busy(dev); 1501 pm_runtime_put_autosuspend(dev); 1502 1503 return ret; 1504 } 1505 1506 static void anx7625_remove_edid(struct anx7625_data *ctx) 1507 { 1508 ctx->slimport_edid_p.edid_block_num = -1; 1509 } 1510 1511 static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) 1512 { 1513 int i; 1514 1515 for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) 1516 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1517 DP_TX_LANE0_SWING_REG0 + i, 1518 ctx->pdata.lane0_reg_data[i]); 1519 1520 for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) 1521 anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, 1522 DP_TX_LANE1_SWING_REG0 + i, 1523 ctx->pdata.lane1_reg_data[i]); 1524 } 1525 1526 static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) 1527 { 1528 struct device *dev = ctx->dev; 1529 1530 /* HPD changed */ 1531 DRM_DEV_DEBUG_DRIVER(dev, "dp_hpd_change_default_func: %d\n", 1532 (u32)on); 1533 1534 if (on == 0) { 1535 DRM_DEV_DEBUG_DRIVER(dev, " HPD low\n"); 1536 anx7625_remove_edid(ctx); 1537 anx7625_stop_dp_work(ctx); 1538 } else { 1539 DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); 1540 anx7625_start_dp_work(ctx); 1541 anx7625_dp_adjust_swing(ctx); 1542 } 1543 } 1544 1545 static int anx7625_hpd_change_detect(struct anx7625_data *ctx) 1546 { 1547 int intr_vector, status; 1548 struct device *dev = ctx->dev; 1549 1550 status = anx7625_reg_write(ctx, ctx->i2c.tcpc_client, 1551 INTR_ALERT_1, 0xFF); 1552 if (status < 0) { 1553 DRM_DEV_ERROR(dev, "cannot clear alert reg.\n"); 1554 return status; 1555 } 1556 1557 intr_vector = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1558 INTERFACE_CHANGE_INT); 1559 if (intr_vector < 0) { 1560 DRM_DEV_ERROR(dev, "cannot access interrupt change reg.\n"); 1561 return intr_vector; 1562 } 1563 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x44=%x\n", intr_vector); 1564 status = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, 1565 INTERFACE_CHANGE_INT, 1566 intr_vector & (~intr_vector)); 1567 if (status < 0) { 1568 DRM_DEV_ERROR(dev, "cannot clear interrupt change reg.\n"); 1569 return status; 1570 } 1571 1572 if (!(intr_vector & HPD_STATUS_CHANGE)) 1573 return -ENOENT; 1574 1575 status = anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, 1576 SYSTEM_STSTUS); 1577 if (status < 0) { 1578 DRM_DEV_ERROR(dev, "cannot clear interrupt status.\n"); 1579 return status; 1580 } 1581 1582 DRM_DEV_DEBUG_DRIVER(dev, "0x7e:0x45=%x\n", status); 1583 dp_hpd_change_handler(ctx, status & HPD_STATUS); 1584 1585 return 0; 1586 } 1587 1588 static void anx7625_work_func(struct work_struct *work) 1589 { 1590 int event; 1591 struct anx7625_data *ctx = container_of(work, 1592 struct anx7625_data, work); 1593 1594 mutex_lock(&ctx->lock); 1595 1596 if (pm_runtime_suspended(ctx->dev)) { 1597 mutex_unlock(&ctx->lock); 1598 return; 1599 } 1600 1601 event = anx7625_hpd_change_detect(ctx); 1602 1603 mutex_unlock(&ctx->lock); 1604 1605 if (event < 0) 1606 return; 1607 1608 if (ctx->bridge_attached) 1609 drm_helper_hpd_irq_event(ctx->bridge.dev); 1610 } 1611 1612 static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) 1613 { 1614 struct anx7625_data *ctx = (struct anx7625_data *)data; 1615 1616 queue_work(ctx->workqueue, &ctx->work); 1617 1618 return IRQ_HANDLED; 1619 } 1620 1621 static int anx7625_get_swing_setting(struct device *dev, 1622 struct anx7625_platform_data *pdata) 1623 { 1624 int num_regs; 1625 1626 if (of_get_property(dev->of_node, 1627 "analogix,lane0-swing", &num_regs)) { 1628 if (num_regs > DP_TX_SWING_REG_CNT) 1629 num_regs = DP_TX_SWING_REG_CNT; 1630 1631 pdata->dp_lane0_swing_reg_cnt = num_regs; 1632 of_property_read_u8_array(dev->of_node, "analogix,lane0-swing", 1633 pdata->lane0_reg_data, num_regs); 1634 } 1635 1636 if (of_get_property(dev->of_node, 1637 "analogix,lane1-swing", &num_regs)) { 1638 if (num_regs > DP_TX_SWING_REG_CNT) 1639 num_regs = DP_TX_SWING_REG_CNT; 1640 1641 pdata->dp_lane1_swing_reg_cnt = num_regs; 1642 of_property_read_u8_array(dev->of_node, "analogix,lane1-swing", 1643 pdata->lane1_reg_data, num_regs); 1644 } 1645 1646 return 0; 1647 } 1648 1649 static int anx7625_parse_dt(struct device *dev, 1650 struct anx7625_platform_data *pdata) 1651 { 1652 struct device_node *np = dev->of_node, *ep0; 1653 int bus_type, mipi_lanes; 1654 1655 anx7625_get_swing_setting(dev, pdata); 1656 1657 pdata->is_dpi = 0; /* default dsi mode */ 1658 of_node_put(pdata->mipi_host_node); 1659 pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); 1660 if (!pdata->mipi_host_node) { 1661 DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); 1662 return -ENODEV; 1663 } 1664 1665 bus_type = 0; 1666 mipi_lanes = MAX_LANES_SUPPORT; 1667 ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); 1668 if (ep0) { 1669 if (of_property_read_u32(ep0, "bus-type", &bus_type)) 1670 bus_type = 0; 1671 1672 mipi_lanes = drm_of_get_data_lanes_count(ep0, 1, MAX_LANES_SUPPORT); 1673 of_node_put(ep0); 1674 } 1675 1676 if (bus_type == V4L2_FWNODE_BUS_TYPE_DPI) /* bus type is DPI */ 1677 pdata->is_dpi = 1; 1678 1679 pdata->mipi_lanes = MAX_LANES_SUPPORT; 1680 if (mipi_lanes > 0) 1681 pdata->mipi_lanes = mipi_lanes; 1682 1683 if (pdata->is_dpi) 1684 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); 1685 else 1686 DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); 1687 1688 if (of_property_read_bool(np, "analogix,audio-enable")) 1689 pdata->audio_en = 1; 1690 1691 return 0; 1692 } 1693 1694 static int anx7625_parse_dt_panel(struct device *dev, 1695 struct anx7625_platform_data *pdata) 1696 { 1697 struct device_node *np = dev->of_node; 1698 1699 pdata->panel_bridge = devm_drm_of_get_bridge(dev, np, 1, 0); 1700 if (IS_ERR(pdata->panel_bridge)) { 1701 if (PTR_ERR(pdata->panel_bridge) == -ENODEV) { 1702 pdata->panel_bridge = NULL; 1703 return 0; 1704 } 1705 1706 return PTR_ERR(pdata->panel_bridge); 1707 } 1708 1709 DRM_DEV_DEBUG_DRIVER(dev, "get panel node.\n"); 1710 1711 return 0; 1712 } 1713 1714 static bool anx7625_of_panel_on_aux_bus(struct device *dev) 1715 { 1716 struct device_node *bus, *panel; 1717 1718 bus = of_get_child_by_name(dev->of_node, "aux-bus"); 1719 if (!bus) 1720 return false; 1721 1722 panel = of_get_child_by_name(bus, "panel"); 1723 of_node_put(bus); 1724 if (!panel) 1725 return false; 1726 of_node_put(panel); 1727 1728 return true; 1729 } 1730 1731 static inline struct anx7625_data *bridge_to_anx7625(struct drm_bridge *bridge) 1732 { 1733 return container_of(bridge, struct anx7625_data, bridge); 1734 } 1735 1736 static ssize_t anx7625_aux_transfer(struct drm_dp_aux *aux, 1737 struct drm_dp_aux_msg *msg) 1738 { 1739 struct anx7625_data *ctx = container_of(aux, struct anx7625_data, aux); 1740 struct device *dev = ctx->dev; 1741 u8 request = msg->request & ~DP_AUX_I2C_MOT; 1742 int ret = 0; 1743 1744 mutex_lock(&ctx->aux_lock); 1745 pm_runtime_get_sync(dev); 1746 msg->reply = 0; 1747 switch (request) { 1748 case DP_AUX_NATIVE_WRITE: 1749 case DP_AUX_I2C_WRITE: 1750 case DP_AUX_NATIVE_READ: 1751 case DP_AUX_I2C_READ: 1752 break; 1753 default: 1754 ret = -EINVAL; 1755 } 1756 if (!ret) 1757 ret = anx7625_aux_trans(ctx, msg->request, msg->address, 1758 msg->size, msg->buffer); 1759 pm_runtime_mark_last_busy(dev); 1760 pm_runtime_put_autosuspend(dev); 1761 mutex_unlock(&ctx->aux_lock); 1762 1763 return ret; 1764 } 1765 1766 static struct edid *anx7625_get_edid(struct anx7625_data *ctx) 1767 { 1768 struct device *dev = ctx->dev; 1769 struct s_edid_data *p_edid = &ctx->slimport_edid_p; 1770 int edid_num; 1771 u8 *edid; 1772 1773 edid = kmalloc(FOUR_BLOCK_SIZE, GFP_KERNEL); 1774 if (!edid) { 1775 DRM_DEV_ERROR(dev, "Fail to allocate buffer\n"); 1776 return NULL; 1777 } 1778 1779 if (ctx->slimport_edid_p.edid_block_num > 0) { 1780 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, 1781 FOUR_BLOCK_SIZE); 1782 return (struct edid *)edid; 1783 } 1784 1785 pm_runtime_get_sync(dev); 1786 _anx7625_hpd_polling(ctx, 5000 * 100); 1787 edid_num = sp_tx_edid_read(ctx, p_edid->edid_raw_data); 1788 pm_runtime_put_sync(dev); 1789 1790 if (edid_num < 1) { 1791 DRM_DEV_ERROR(dev, "Fail to read EDID: %d\n", edid_num); 1792 kfree(edid); 1793 return NULL; 1794 } 1795 1796 p_edid->edid_block_num = edid_num; 1797 1798 memcpy(edid, ctx->slimport_edid_p.edid_raw_data, FOUR_BLOCK_SIZE); 1799 return (struct edid *)edid; 1800 } 1801 1802 static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) 1803 { 1804 struct device *dev = ctx->dev; 1805 1806 DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); 1807 1808 if (ctx->pdata.panel_bridge) 1809 return connector_status_connected; 1810 1811 return ctx->hpd_status ? connector_status_connected : 1812 connector_status_disconnected; 1813 } 1814 1815 static int anx7625_audio_hw_params(struct device *dev, void *data, 1816 struct hdmi_codec_daifmt *fmt, 1817 struct hdmi_codec_params *params) 1818 { 1819 struct anx7625_data *ctx = dev_get_drvdata(dev); 1820 int wl, ch, rate; 1821 int ret = 0; 1822 1823 if (anx7625_sink_detect(ctx) == connector_status_disconnected) { 1824 DRM_DEV_DEBUG_DRIVER(dev, "DP not connected\n"); 1825 return 0; 1826 } 1827 1828 if (fmt->fmt != HDMI_DSP_A && fmt->fmt != HDMI_I2S) { 1829 DRM_DEV_ERROR(dev, "only supports DSP_A & I2S\n"); 1830 return -EINVAL; 1831 } 1832 1833 DRM_DEV_DEBUG_DRIVER(dev, "setting %d Hz, %d bit, %d channels\n", 1834 params->sample_rate, params->sample_width, 1835 params->cea.channels); 1836 1837 if (fmt->fmt == HDMI_DSP_A) 1838 ret = anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1839 AUDIO_CHANNEL_STATUS_6, 1840 ~I2S_SLAVE_MODE, 1841 TDM_SLAVE_MODE); 1842 else 1843 ret = anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1844 AUDIO_CHANNEL_STATUS_6, 1845 ~TDM_SLAVE_MODE, 1846 I2S_SLAVE_MODE); 1847 1848 /* Word length */ 1849 switch (params->sample_width) { 1850 case 16: 1851 wl = AUDIO_W_LEN_16_20MAX; 1852 break; 1853 case 18: 1854 wl = AUDIO_W_LEN_18_20MAX; 1855 break; 1856 case 20: 1857 wl = AUDIO_W_LEN_20_20MAX; 1858 break; 1859 case 24: 1860 wl = AUDIO_W_LEN_24_24MAX; 1861 break; 1862 default: 1863 DRM_DEV_DEBUG_DRIVER(dev, "wordlength: %d bit not support", 1864 params->sample_width); 1865 return -EINVAL; 1866 } 1867 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1868 AUDIO_CHANNEL_STATUS_5, 1869 0xf0, wl); 1870 1871 /* Channel num */ 1872 switch (params->cea.channels) { 1873 case 2: 1874 ch = I2S_CH_2; 1875 break; 1876 case 4: 1877 ch = TDM_CH_4; 1878 break; 1879 case 6: 1880 ch = TDM_CH_6; 1881 break; 1882 case 8: 1883 ch = TDM_CH_8; 1884 break; 1885 default: 1886 DRM_DEV_DEBUG_DRIVER(dev, "channel number: %d not support", 1887 params->cea.channels); 1888 return -EINVAL; 1889 } 1890 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1891 AUDIO_CHANNEL_STATUS_6, 0x1f, ch << 5); 1892 if (ch > I2S_CH_2) 1893 ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, 1894 AUDIO_CHANNEL_STATUS_6, AUDIO_LAYOUT); 1895 else 1896 ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 1897 AUDIO_CHANNEL_STATUS_6, ~AUDIO_LAYOUT); 1898 1899 /* FS */ 1900 switch (params->sample_rate) { 1901 case 32000: 1902 rate = AUDIO_FS_32K; 1903 break; 1904 case 44100: 1905 rate = AUDIO_FS_441K; 1906 break; 1907 case 48000: 1908 rate = AUDIO_FS_48K; 1909 break; 1910 case 88200: 1911 rate = AUDIO_FS_882K; 1912 break; 1913 case 96000: 1914 rate = AUDIO_FS_96K; 1915 break; 1916 case 176400: 1917 rate = AUDIO_FS_1764K; 1918 break; 1919 case 192000: 1920 rate = AUDIO_FS_192K; 1921 break; 1922 default: 1923 DRM_DEV_DEBUG_DRIVER(dev, "sample rate: %d not support", 1924 params->sample_rate); 1925 return -EINVAL; 1926 } 1927 ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, 1928 AUDIO_CHANNEL_STATUS_4, 1929 0xf0, rate); 1930 ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, 1931 AP_AV_STATUS, AP_AUDIO_CHG); 1932 if (ret < 0) { 1933 DRM_DEV_ERROR(dev, "IO error : config audio.\n"); 1934 return -EIO; 1935 } 1936 1937 return 0; 1938 } 1939 1940 static void anx7625_audio_shutdown(struct device *dev, void *data) 1941 { 1942 DRM_DEV_DEBUG_DRIVER(dev, "stop audio\n"); 1943 } 1944 1945 static int anx7625_hdmi_i2s_get_dai_id(struct snd_soc_component *component, 1946 struct device_node *endpoint) 1947 { 1948 struct of_endpoint of_ep; 1949 int ret; 1950 1951 ret = of_graph_parse_endpoint(endpoint, &of_ep); 1952 if (ret < 0) 1953 return ret; 1954 1955 /* 1956 * HDMI sound should be located at external DPI port 1957 * Didn't have good way to check where is internal(DSI) 1958 * or external(DPI) bridge 1959 */ 1960 return 0; 1961 } 1962 1963 static void 1964 anx7625_audio_update_connector_status(struct anx7625_data *ctx, 1965 enum drm_connector_status status) 1966 { 1967 if (ctx->plugged_cb && ctx->codec_dev) { 1968 ctx->plugged_cb(ctx->codec_dev, 1969 status == connector_status_connected); 1970 } 1971 } 1972 1973 static int anx7625_audio_hook_plugged_cb(struct device *dev, void *data, 1974 hdmi_codec_plugged_cb fn, 1975 struct device *codec_dev) 1976 { 1977 struct anx7625_data *ctx = data; 1978 1979 ctx->plugged_cb = fn; 1980 ctx->codec_dev = codec_dev; 1981 anx7625_audio_update_connector_status(ctx, anx7625_sink_detect(ctx)); 1982 1983 return 0; 1984 } 1985 1986 static int anx7625_audio_get_eld(struct device *dev, void *data, 1987 u8 *buf, size_t len) 1988 { 1989 struct anx7625_data *ctx = dev_get_drvdata(dev); 1990 1991 if (!ctx->connector) { 1992 /* Pass en empty ELD if connector not available */ 1993 memset(buf, 0, len); 1994 } else { 1995 dev_dbg(dev, "audio copy eld\n"); 1996 memcpy(buf, ctx->connector->eld, 1997 min(sizeof(ctx->connector->eld), len)); 1998 } 1999 2000 return 0; 2001 } 2002 2003 static const struct hdmi_codec_ops anx7625_codec_ops = { 2004 .hw_params = anx7625_audio_hw_params, 2005 .audio_shutdown = anx7625_audio_shutdown, 2006 .get_eld = anx7625_audio_get_eld, 2007 .get_dai_id = anx7625_hdmi_i2s_get_dai_id, 2008 .hook_plugged_cb = anx7625_audio_hook_plugged_cb, 2009 }; 2010 2011 static void anx7625_unregister_audio(struct anx7625_data *ctx) 2012 { 2013 struct device *dev = ctx->dev; 2014 2015 if (ctx->audio_pdev) { 2016 platform_device_unregister(ctx->audio_pdev); 2017 ctx->audio_pdev = NULL; 2018 } 2019 2020 DRM_DEV_DEBUG_DRIVER(dev, "unbound to %s", HDMI_CODEC_DRV_NAME); 2021 } 2022 2023 static int anx7625_register_audio(struct device *dev, struct anx7625_data *ctx) 2024 { 2025 struct hdmi_codec_pdata codec_data = { 2026 .ops = &anx7625_codec_ops, 2027 .max_i2s_channels = 8, 2028 .i2s = 1, 2029 .data = ctx, 2030 }; 2031 2032 ctx->audio_pdev = platform_device_register_data(dev, 2033 HDMI_CODEC_DRV_NAME, 2034 PLATFORM_DEVID_AUTO, 2035 &codec_data, 2036 sizeof(codec_data)); 2037 2038 if (IS_ERR(ctx->audio_pdev)) 2039 return PTR_ERR(ctx->audio_pdev); 2040 2041 DRM_DEV_DEBUG_DRIVER(dev, "bound to %s", HDMI_CODEC_DRV_NAME); 2042 2043 return 0; 2044 } 2045 2046 static int anx7625_setup_dsi_device(struct anx7625_data *ctx) 2047 { 2048 struct mipi_dsi_device *dsi; 2049 struct device *dev = ctx->dev; 2050 struct mipi_dsi_host *host; 2051 const struct mipi_dsi_device_info info = { 2052 .type = "anx7625", 2053 .channel = 0, 2054 .node = NULL, 2055 }; 2056 2057 host = of_find_mipi_dsi_host_by_node(ctx->pdata.mipi_host_node); 2058 if (!host) { 2059 DRM_DEV_ERROR(dev, "fail to find dsi host.\n"); 2060 return -EPROBE_DEFER; 2061 } 2062 2063 dsi = devm_mipi_dsi_device_register_full(dev, host, &info); 2064 if (IS_ERR(dsi)) { 2065 DRM_DEV_ERROR(dev, "fail to create dsi device.\n"); 2066 return -EINVAL; 2067 } 2068 2069 dsi->lanes = ctx->pdata.mipi_lanes; 2070 dsi->format = MIPI_DSI_FMT_RGB888; 2071 dsi->mode_flags = MIPI_DSI_MODE_VIDEO | 2072 MIPI_DSI_MODE_VIDEO_SYNC_PULSE | 2073 MIPI_DSI_MODE_VIDEO_HSE | 2074 MIPI_DSI_HS_PKT_END_ALIGNED; 2075 2076 ctx->dsi = dsi; 2077 2078 return 0; 2079 } 2080 2081 static int anx7625_attach_dsi(struct anx7625_data *ctx) 2082 { 2083 struct device *dev = ctx->dev; 2084 int ret; 2085 2086 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi\n"); 2087 2088 ret = devm_mipi_dsi_attach(dev, ctx->dsi); 2089 if (ret) { 2090 DRM_DEV_ERROR(dev, "fail to attach dsi to host.\n"); 2091 return ret; 2092 } 2093 2094 DRM_DEV_DEBUG_DRIVER(dev, "attach dsi succeeded.\n"); 2095 2096 return 0; 2097 } 2098 2099 static void hdcp_check_work_func(struct work_struct *work) 2100 { 2101 u8 status; 2102 struct delayed_work *dwork; 2103 struct anx7625_data *ctx; 2104 struct device *dev; 2105 struct drm_device *drm_dev; 2106 2107 dwork = to_delayed_work(work); 2108 ctx = container_of(dwork, struct anx7625_data, hdcp_work); 2109 dev = ctx->dev; 2110 2111 if (!ctx->connector) { 2112 dev_err(dev, "HDCP connector is null!"); 2113 return; 2114 } 2115 2116 drm_dev = ctx->connector->dev; 2117 drm_modeset_lock(&drm_dev->mode_config.connection_mutex, NULL); 2118 mutex_lock(&ctx->hdcp_wq_lock); 2119 2120 status = anx7625_reg_read(ctx, ctx->i2c.tx_p0_client, 0); 2121 dev_dbg(dev, "sink HDCP status check: %.02x\n", status); 2122 if (status & BIT(1)) { 2123 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_ENABLED; 2124 drm_hdcp_update_content_protection(ctx->connector, 2125 ctx->hdcp_cp); 2126 dev_dbg(dev, "update CP to ENABLE\n"); 2127 } 2128 2129 mutex_unlock(&ctx->hdcp_wq_lock); 2130 drm_modeset_unlock(&drm_dev->mode_config.connection_mutex); 2131 } 2132 2133 static int anx7625_connector_atomic_check(struct anx7625_data *ctx, 2134 struct drm_connector_state *state) 2135 { 2136 struct device *dev = ctx->dev; 2137 int cp; 2138 2139 dev_dbg(dev, "hdcp state check\n"); 2140 cp = state->content_protection; 2141 2142 if (cp == ctx->hdcp_cp) 2143 return 0; 2144 2145 if (cp == DRM_MODE_CONTENT_PROTECTION_DESIRED) { 2146 if (ctx->dp_en) { 2147 dev_dbg(dev, "enable HDCP\n"); 2148 anx7625_hdcp_enable(ctx); 2149 2150 queue_delayed_work(ctx->hdcp_workqueue, 2151 &ctx->hdcp_work, 2152 msecs_to_jiffies(2000)); 2153 } 2154 } 2155 2156 if (cp == DRM_MODE_CONTENT_PROTECTION_UNDESIRED) { 2157 if (ctx->hdcp_cp != DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2158 dev_err(dev, "current CP is not ENABLED\n"); 2159 return -EINVAL; 2160 } 2161 anx7625_hdcp_disable(ctx); 2162 ctx->hdcp_cp = DRM_MODE_CONTENT_PROTECTION_UNDESIRED; 2163 drm_hdcp_update_content_protection(ctx->connector, 2164 ctx->hdcp_cp); 2165 dev_dbg(dev, "update CP to UNDESIRE\n"); 2166 } 2167 2168 if (cp == DRM_MODE_CONTENT_PROTECTION_ENABLED) { 2169 dev_err(dev, "Userspace illegal set to PROTECTION ENABLE\n"); 2170 return -EINVAL; 2171 } 2172 2173 return 0; 2174 } 2175 2176 static int anx7625_bridge_attach(struct drm_bridge *bridge, 2177 enum drm_bridge_attach_flags flags) 2178 { 2179 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2180 int err; 2181 struct device *dev = ctx->dev; 2182 2183 DRM_DEV_DEBUG_DRIVER(dev, "drm attach\n"); 2184 if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) 2185 return -EINVAL; 2186 2187 if (!bridge->encoder) { 2188 DRM_DEV_ERROR(dev, "Parent encoder object not found"); 2189 return -ENODEV; 2190 } 2191 2192 ctx->aux.drm_dev = bridge->dev; 2193 err = drm_dp_aux_register(&ctx->aux); 2194 if (err) { 2195 dev_err(dev, "failed to register aux channel: %d\n", err); 2196 return err; 2197 } 2198 2199 if (ctx->pdata.panel_bridge) { 2200 err = drm_bridge_attach(bridge->encoder, 2201 ctx->pdata.panel_bridge, 2202 &ctx->bridge, flags); 2203 if (err) 2204 return err; 2205 } 2206 2207 ctx->bridge_attached = 1; 2208 2209 return 0; 2210 } 2211 2212 static void anx7625_bridge_detach(struct drm_bridge *bridge) 2213 { 2214 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2215 2216 drm_dp_aux_unregister(&ctx->aux); 2217 } 2218 2219 static enum drm_mode_status 2220 anx7625_bridge_mode_valid(struct drm_bridge *bridge, 2221 const struct drm_display_info *info, 2222 const struct drm_display_mode *mode) 2223 { 2224 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2225 struct device *dev = ctx->dev; 2226 2227 DRM_DEV_DEBUG_DRIVER(dev, "drm mode checking\n"); 2228 2229 /* Max 1200p at 5.4 Ghz, one lane, pixel clock 300M */ 2230 if (mode->clock > SUPPORT_PIXEL_CLOCK) { 2231 DRM_DEV_DEBUG_DRIVER(dev, 2232 "drm mode invalid, pixelclock too high.\n"); 2233 return MODE_CLOCK_HIGH; 2234 } 2235 2236 DRM_DEV_DEBUG_DRIVER(dev, "drm mode valid.\n"); 2237 2238 return MODE_OK; 2239 } 2240 2241 static void anx7625_bridge_mode_set(struct drm_bridge *bridge, 2242 const struct drm_display_mode *old_mode, 2243 const struct drm_display_mode *mode) 2244 { 2245 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2246 struct device *dev = ctx->dev; 2247 2248 DRM_DEV_DEBUG_DRIVER(dev, "drm mode set\n"); 2249 2250 ctx->dt.pixelclock.min = mode->clock; 2251 ctx->dt.hactive.min = mode->hdisplay; 2252 ctx->dt.hsync_len.min = mode->hsync_end - mode->hsync_start; 2253 ctx->dt.hfront_porch.min = mode->hsync_start - mode->hdisplay; 2254 ctx->dt.hback_porch.min = mode->htotal - mode->hsync_end; 2255 ctx->dt.vactive.min = mode->vdisplay; 2256 ctx->dt.vsync_len.min = mode->vsync_end - mode->vsync_start; 2257 ctx->dt.vfront_porch.min = mode->vsync_start - mode->vdisplay; 2258 ctx->dt.vback_porch.min = mode->vtotal - mode->vsync_end; 2259 2260 ctx->display_timing_valid = 1; 2261 2262 DRM_DEV_DEBUG_DRIVER(dev, "pixelclock(%d).\n", ctx->dt.pixelclock.min); 2263 DRM_DEV_DEBUG_DRIVER(dev, "hactive(%d), hsync(%d), hfp(%d), hbp(%d)\n", 2264 ctx->dt.hactive.min, 2265 ctx->dt.hsync_len.min, 2266 ctx->dt.hfront_porch.min, 2267 ctx->dt.hback_porch.min); 2268 DRM_DEV_DEBUG_DRIVER(dev, "vactive(%d), vsync(%d), vfp(%d), vbp(%d)\n", 2269 ctx->dt.vactive.min, 2270 ctx->dt.vsync_len.min, 2271 ctx->dt.vfront_porch.min, 2272 ctx->dt.vback_porch.min); 2273 DRM_DEV_DEBUG_DRIVER(dev, "hdisplay(%d),hsync_start(%d).\n", 2274 mode->hdisplay, 2275 mode->hsync_start); 2276 DRM_DEV_DEBUG_DRIVER(dev, "hsync_end(%d),htotal(%d).\n", 2277 mode->hsync_end, 2278 mode->htotal); 2279 DRM_DEV_DEBUG_DRIVER(dev, "vdisplay(%d),vsync_start(%d).\n", 2280 mode->vdisplay, 2281 mode->vsync_start); 2282 DRM_DEV_DEBUG_DRIVER(dev, "vsync_end(%d),vtotal(%d).\n", 2283 mode->vsync_end, 2284 mode->vtotal); 2285 } 2286 2287 static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, 2288 const struct drm_display_mode *mode, 2289 struct drm_display_mode *adj) 2290 { 2291 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2292 struct device *dev = ctx->dev; 2293 u32 hsync, hfp, hbp, hblanking; 2294 u32 adj_hsync, adj_hfp, adj_hbp, adj_hblanking, delta_adj; 2295 u32 vref, adj_clock; 2296 2297 DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); 2298 2299 /* No need fixup for external monitor */ 2300 if (!ctx->pdata.panel_bridge) 2301 return true; 2302 2303 hsync = mode->hsync_end - mode->hsync_start; 2304 hfp = mode->hsync_start - mode->hdisplay; 2305 hbp = mode->htotal - mode->hsync_end; 2306 hblanking = mode->htotal - mode->hdisplay; 2307 2308 DRM_DEV_DEBUG_DRIVER(dev, "before mode fixup\n"); 2309 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2310 hsync, hfp, hbp, adj->clock); 2311 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2312 adj->hsync_start, adj->hsync_end, adj->htotal); 2313 2314 adj_hfp = hfp; 2315 adj_hsync = hsync; 2316 adj_hbp = hbp; 2317 adj_hblanking = hblanking; 2318 2319 /* HFP needs to be even */ 2320 if (hfp & 0x1) { 2321 adj_hfp += 1; 2322 adj_hblanking += 1; 2323 } 2324 2325 /* HBP needs to be even */ 2326 if (hbp & 0x1) { 2327 adj_hbp -= 1; 2328 adj_hblanking -= 1; 2329 } 2330 2331 /* HSYNC needs to be even */ 2332 if (hsync & 0x1) { 2333 if (adj_hblanking < hblanking) 2334 adj_hsync += 1; 2335 else 2336 adj_hsync -= 1; 2337 } 2338 2339 /* 2340 * Once illegal timing detected, use default HFP, HSYNC, HBP 2341 * This adjusting made for built-in eDP panel, for the externel 2342 * DP monitor, may need return false. 2343 */ 2344 if (hblanking < HBLANKING_MIN || (hfp < HP_MIN && hbp < HP_MIN)) { 2345 adj_hsync = SYNC_LEN_DEF; 2346 adj_hfp = HFP_HBP_DEF; 2347 adj_hbp = HFP_HBP_DEF; 2348 vref = adj->clock * 1000 / (adj->htotal * adj->vtotal); 2349 if (hblanking < HBLANKING_MIN) { 2350 delta_adj = HBLANKING_MIN - hblanking; 2351 adj_clock = vref * delta_adj * adj->vtotal; 2352 adj->clock += DIV_ROUND_UP(adj_clock, 1000); 2353 } else { 2354 delta_adj = hblanking - HBLANKING_MIN; 2355 adj_clock = vref * delta_adj * adj->vtotal; 2356 adj->clock -= DIV_ROUND_UP(adj_clock, 1000); 2357 } 2358 2359 DRM_WARN("illegal hblanking timing, use default.\n"); 2360 DRM_WARN("hfp(%d), hbp(%d), hsync(%d).\n", hfp, hbp, hsync); 2361 } else if (adj_hfp < HP_MIN) { 2362 /* Adjust hfp if hfp less than HP_MIN */ 2363 delta_adj = HP_MIN - adj_hfp; 2364 adj_hfp = HP_MIN; 2365 2366 /* 2367 * Balance total HBlanking pixel, if HBP does not have enough 2368 * space, adjust HSYNC length, otherwise adjust HBP 2369 */ 2370 if ((adj_hbp - delta_adj) < HP_MIN) 2371 /* HBP not enough space */ 2372 adj_hsync -= delta_adj; 2373 else 2374 adj_hbp -= delta_adj; 2375 } else if (adj_hbp < HP_MIN) { 2376 delta_adj = HP_MIN - adj_hbp; 2377 adj_hbp = HP_MIN; 2378 2379 /* 2380 * Balance total HBlanking pixel, if HBP hasn't enough space, 2381 * adjust HSYNC length, otherwize adjust HBP 2382 */ 2383 if ((adj_hfp - delta_adj) < HP_MIN) 2384 /* HFP not enough space */ 2385 adj_hsync -= delta_adj; 2386 else 2387 adj_hfp -= delta_adj; 2388 } 2389 2390 DRM_DEV_DEBUG_DRIVER(dev, "after mode fixup\n"); 2391 DRM_DEV_DEBUG_DRIVER(dev, "hsync(%d), hfp(%d), hbp(%d), clock(%d)\n", 2392 adj_hsync, adj_hfp, adj_hbp, adj->clock); 2393 2394 /* Reconstruct timing */ 2395 adj->hsync_start = adj->hdisplay + adj_hfp; 2396 adj->hsync_end = adj->hsync_start + adj_hsync; 2397 adj->htotal = adj->hsync_end + adj_hbp; 2398 DRM_DEV_DEBUG_DRIVER(dev, "hsync_start(%d), hsync_end(%d), htot(%d)\n", 2399 adj->hsync_start, adj->hsync_end, adj->htotal); 2400 2401 return true; 2402 } 2403 2404 static int anx7625_bridge_atomic_check(struct drm_bridge *bridge, 2405 struct drm_bridge_state *bridge_state, 2406 struct drm_crtc_state *crtc_state, 2407 struct drm_connector_state *conn_state) 2408 { 2409 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2410 struct device *dev = ctx->dev; 2411 2412 dev_dbg(dev, "drm bridge atomic check\n"); 2413 2414 anx7625_bridge_mode_fixup(bridge, &crtc_state->mode, 2415 &crtc_state->adjusted_mode); 2416 2417 return anx7625_connector_atomic_check(ctx, conn_state); 2418 } 2419 2420 static void anx7625_bridge_atomic_enable(struct drm_bridge *bridge, 2421 struct drm_bridge_state *state) 2422 { 2423 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2424 struct device *dev = ctx->dev; 2425 struct drm_connector *connector; 2426 2427 dev_dbg(dev, "drm atomic enable\n"); 2428 2429 if (!bridge->encoder) { 2430 dev_err(dev, "Parent encoder object not found"); 2431 return; 2432 } 2433 2434 connector = drm_atomic_get_new_connector_for_encoder(state->base.state, 2435 bridge->encoder); 2436 if (!connector) 2437 return; 2438 2439 ctx->connector = connector; 2440 2441 pm_runtime_get_sync(dev); 2442 _anx7625_hpd_polling(ctx, 5000 * 100); 2443 2444 anx7625_dp_start(ctx); 2445 } 2446 2447 static void anx7625_bridge_atomic_disable(struct drm_bridge *bridge, 2448 struct drm_bridge_state *old) 2449 { 2450 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2451 struct device *dev = ctx->dev; 2452 2453 dev_dbg(dev, "drm atomic disable\n"); 2454 2455 ctx->connector = NULL; 2456 anx7625_dp_stop(ctx); 2457 2458 mutex_lock(&ctx->aux_lock); 2459 pm_runtime_put_sync_suspend(dev); 2460 mutex_unlock(&ctx->aux_lock); 2461 } 2462 2463 static enum drm_connector_status 2464 anx7625_bridge_detect(struct drm_bridge *bridge) 2465 { 2466 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2467 struct device *dev = ctx->dev; 2468 2469 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge detect\n"); 2470 2471 return anx7625_sink_detect(ctx); 2472 } 2473 2474 static struct edid *anx7625_bridge_get_edid(struct drm_bridge *bridge, 2475 struct drm_connector *connector) 2476 { 2477 struct anx7625_data *ctx = bridge_to_anx7625(bridge); 2478 struct device *dev = ctx->dev; 2479 2480 DRM_DEV_DEBUG_DRIVER(dev, "drm bridge get edid\n"); 2481 2482 return anx7625_get_edid(ctx); 2483 } 2484 2485 static const struct drm_bridge_funcs anx7625_bridge_funcs = { 2486 .attach = anx7625_bridge_attach, 2487 .detach = anx7625_bridge_detach, 2488 .mode_valid = anx7625_bridge_mode_valid, 2489 .mode_set = anx7625_bridge_mode_set, 2490 .atomic_check = anx7625_bridge_atomic_check, 2491 .atomic_enable = anx7625_bridge_atomic_enable, 2492 .atomic_disable = anx7625_bridge_atomic_disable, 2493 .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, 2494 .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, 2495 .atomic_reset = drm_atomic_helper_bridge_reset, 2496 .detect = anx7625_bridge_detect, 2497 .get_edid = anx7625_bridge_get_edid, 2498 }; 2499 2500 static int anx7625_register_i2c_dummy_clients(struct anx7625_data *ctx, 2501 struct i2c_client *client) 2502 { 2503 struct device *dev = ctx->dev; 2504 2505 ctx->i2c.tx_p0_client = devm_i2c_new_dummy_device(dev, client->adapter, 2506 TX_P0_ADDR >> 1); 2507 if (IS_ERR(ctx->i2c.tx_p0_client)) 2508 return PTR_ERR(ctx->i2c.tx_p0_client); 2509 2510 ctx->i2c.tx_p1_client = devm_i2c_new_dummy_device(dev, client->adapter, 2511 TX_P1_ADDR >> 1); 2512 if (IS_ERR(ctx->i2c.tx_p1_client)) 2513 return PTR_ERR(ctx->i2c.tx_p1_client); 2514 2515 ctx->i2c.tx_p2_client = devm_i2c_new_dummy_device(dev, client->adapter, 2516 TX_P2_ADDR >> 1); 2517 if (IS_ERR(ctx->i2c.tx_p2_client)) 2518 return PTR_ERR(ctx->i2c.tx_p2_client); 2519 2520 ctx->i2c.rx_p0_client = devm_i2c_new_dummy_device(dev, client->adapter, 2521 RX_P0_ADDR >> 1); 2522 if (IS_ERR(ctx->i2c.rx_p0_client)) 2523 return PTR_ERR(ctx->i2c.rx_p0_client); 2524 2525 ctx->i2c.rx_p1_client = devm_i2c_new_dummy_device(dev, client->adapter, 2526 RX_P1_ADDR >> 1); 2527 if (IS_ERR(ctx->i2c.rx_p1_client)) 2528 return PTR_ERR(ctx->i2c.rx_p1_client); 2529 2530 ctx->i2c.rx_p2_client = devm_i2c_new_dummy_device(dev, client->adapter, 2531 RX_P2_ADDR >> 1); 2532 if (IS_ERR(ctx->i2c.rx_p2_client)) 2533 return PTR_ERR(ctx->i2c.rx_p2_client); 2534 2535 ctx->i2c.tcpc_client = devm_i2c_new_dummy_device(dev, client->adapter, 2536 TCPC_INTERFACE_ADDR >> 1); 2537 if (IS_ERR(ctx->i2c.tcpc_client)) 2538 return PTR_ERR(ctx->i2c.tcpc_client); 2539 2540 return 0; 2541 } 2542 2543 static int __maybe_unused anx7625_runtime_pm_suspend(struct device *dev) 2544 { 2545 struct anx7625_data *ctx = dev_get_drvdata(dev); 2546 2547 mutex_lock(&ctx->lock); 2548 2549 anx7625_stop_dp_work(ctx); 2550 anx7625_power_standby(ctx); 2551 2552 mutex_unlock(&ctx->lock); 2553 2554 return 0; 2555 } 2556 2557 static int __maybe_unused anx7625_runtime_pm_resume(struct device *dev) 2558 { 2559 struct anx7625_data *ctx = dev_get_drvdata(dev); 2560 2561 mutex_lock(&ctx->lock); 2562 2563 anx7625_power_on_init(ctx); 2564 2565 mutex_unlock(&ctx->lock); 2566 2567 return 0; 2568 } 2569 2570 static const struct dev_pm_ops anx7625_pm_ops = { 2571 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, 2572 pm_runtime_force_resume) 2573 SET_RUNTIME_PM_OPS(anx7625_runtime_pm_suspend, 2574 anx7625_runtime_pm_resume, NULL) 2575 }; 2576 2577 static void anx7625_runtime_disable(void *data) 2578 { 2579 pm_runtime_dont_use_autosuspend(data); 2580 pm_runtime_disable(data); 2581 } 2582 2583 static int anx7625_link_bridge(struct drm_dp_aux *aux) 2584 { 2585 struct anx7625_data *platform = container_of(aux, struct anx7625_data, aux); 2586 struct device *dev = aux->dev; 2587 int ret; 2588 2589 ret = anx7625_parse_dt_panel(dev, &platform->pdata); 2590 if (ret) { 2591 DRM_DEV_ERROR(dev, "fail to parse DT for panel : %d\n", ret); 2592 return ret; 2593 } 2594 2595 platform->bridge.funcs = &anx7625_bridge_funcs; 2596 platform->bridge.of_node = dev->of_node; 2597 if (!anx7625_of_panel_on_aux_bus(dev)) 2598 platform->bridge.ops |= DRM_BRIDGE_OP_EDID; 2599 if (!platform->pdata.panel_bridge) 2600 platform->bridge.ops |= DRM_BRIDGE_OP_HPD | 2601 DRM_BRIDGE_OP_DETECT; 2602 platform->bridge.type = platform->pdata.panel_bridge ? 2603 DRM_MODE_CONNECTOR_eDP : 2604 DRM_MODE_CONNECTOR_DisplayPort; 2605 2606 drm_bridge_add(&platform->bridge); 2607 2608 if (!platform->pdata.is_dpi) { 2609 ret = anx7625_attach_dsi(platform); 2610 if (ret) 2611 drm_bridge_remove(&platform->bridge); 2612 } 2613 2614 return ret; 2615 } 2616 2617 static int anx7625_i2c_probe(struct i2c_client *client) 2618 { 2619 struct anx7625_data *platform; 2620 struct anx7625_platform_data *pdata; 2621 int ret = 0; 2622 struct device *dev = &client->dev; 2623 2624 if (!i2c_check_functionality(client->adapter, 2625 I2C_FUNC_SMBUS_I2C_BLOCK)) { 2626 DRM_DEV_ERROR(dev, "anx7625's i2c bus doesn't support\n"); 2627 return -ENODEV; 2628 } 2629 2630 platform = devm_kzalloc(dev, sizeof(*platform), GFP_KERNEL); 2631 if (!platform) { 2632 DRM_DEV_ERROR(dev, "fail to allocate driver data\n"); 2633 return -ENOMEM; 2634 } 2635 2636 pdata = &platform->pdata; 2637 2638 platform->dev = &client->dev; 2639 i2c_set_clientdata(client, platform); 2640 2641 pdata->supplies[0].supply = "vdd10"; 2642 pdata->supplies[1].supply = "vdd18"; 2643 pdata->supplies[2].supply = "vdd33"; 2644 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies), 2645 pdata->supplies); 2646 if (ret) { 2647 DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret); 2648 return ret; 2649 } 2650 anx7625_init_gpio(platform); 2651 2652 mutex_init(&platform->lock); 2653 mutex_init(&platform->hdcp_wq_lock); 2654 mutex_init(&platform->aux_lock); 2655 2656 INIT_DELAYED_WORK(&platform->hdcp_work, hdcp_check_work_func); 2657 platform->hdcp_workqueue = create_workqueue("hdcp workqueue"); 2658 if (!platform->hdcp_workqueue) { 2659 dev_err(dev, "fail to create work queue\n"); 2660 ret = -ENOMEM; 2661 return ret; 2662 } 2663 2664 platform->pdata.intp_irq = client->irq; 2665 if (platform->pdata.intp_irq) { 2666 INIT_WORK(&platform->work, anx7625_work_func); 2667 platform->workqueue = alloc_workqueue("anx7625_work", 2668 WQ_FREEZABLE | WQ_MEM_RECLAIM, 1); 2669 if (!platform->workqueue) { 2670 DRM_DEV_ERROR(dev, "fail to create work queue\n"); 2671 ret = -ENOMEM; 2672 goto free_hdcp_wq; 2673 } 2674 2675 ret = devm_request_threaded_irq(dev, platform->pdata.intp_irq, 2676 NULL, anx7625_intr_hpd_isr, 2677 IRQF_TRIGGER_FALLING | 2678 IRQF_ONESHOT, 2679 "anx7625-intp", platform); 2680 if (ret) { 2681 DRM_DEV_ERROR(dev, "fail to request irq\n"); 2682 goto free_wq; 2683 } 2684 } 2685 2686 platform->aux.name = "anx7625-aux"; 2687 platform->aux.dev = dev; 2688 platform->aux.transfer = anx7625_aux_transfer; 2689 platform->aux.wait_hpd_asserted = anx7625_wait_hpd_asserted; 2690 drm_dp_aux_init(&platform->aux); 2691 2692 ret = anx7625_parse_dt(dev, pdata); 2693 if (ret) { 2694 if (ret != -EPROBE_DEFER) 2695 DRM_DEV_ERROR(dev, "fail to parse DT : %d\n", ret); 2696 goto free_wq; 2697 } 2698 2699 if (!platform->pdata.is_dpi) { 2700 ret = anx7625_setup_dsi_device(platform); 2701 if (ret < 0) 2702 goto free_wq; 2703 } 2704 2705 /* 2706 * Registering the i2c devices will retrigger deferred probe, so it 2707 * needs to be done after calls that might return EPROBE_DEFER, 2708 * otherwise we can get an infinite loop. 2709 */ 2710 if (anx7625_register_i2c_dummy_clients(platform, client) != 0) { 2711 ret = -ENOMEM; 2712 DRM_DEV_ERROR(dev, "fail to reserve I2C bus.\n"); 2713 goto free_wq; 2714 } 2715 2716 pm_runtime_enable(dev); 2717 pm_runtime_set_autosuspend_delay(dev, 1000); 2718 pm_runtime_use_autosuspend(dev); 2719 pm_suspend_ignore_children(dev, true); 2720 ret = devm_add_action_or_reset(dev, anx7625_runtime_disable, dev); 2721 if (ret) 2722 goto free_wq; 2723 2724 /* 2725 * Populating the aux bus will retrigger deferred probe, so it needs to 2726 * be done after calls that might return EPROBE_DEFER, otherwise we can 2727 * get an infinite loop. 2728 */ 2729 ret = devm_of_dp_aux_populate_bus(&platform->aux, anx7625_link_bridge); 2730 if (ret) { 2731 if (ret != -ENODEV) { 2732 DRM_DEV_ERROR(dev, "failed to populate aux bus : %d\n", ret); 2733 goto free_wq; 2734 } 2735 2736 ret = anx7625_link_bridge(&platform->aux); 2737 if (ret) 2738 goto free_wq; 2739 } 2740 2741 if (!platform->pdata.low_power_mode) { 2742 anx7625_disable_pd_protocol(platform); 2743 pm_runtime_get_sync(dev); 2744 _anx7625_hpd_polling(platform, 5000 * 100); 2745 } 2746 2747 /* Add work function */ 2748 if (platform->pdata.intp_irq) 2749 queue_work(platform->workqueue, &platform->work); 2750 2751 if (platform->pdata.audio_en) 2752 anx7625_register_audio(dev, platform); 2753 2754 DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); 2755 2756 return 0; 2757 2758 free_wq: 2759 if (platform->workqueue) 2760 destroy_workqueue(platform->workqueue); 2761 2762 free_hdcp_wq: 2763 if (platform->hdcp_workqueue) 2764 destroy_workqueue(platform->hdcp_workqueue); 2765 2766 return ret; 2767 } 2768 2769 static void anx7625_i2c_remove(struct i2c_client *client) 2770 { 2771 struct anx7625_data *platform = i2c_get_clientdata(client); 2772 2773 drm_bridge_remove(&platform->bridge); 2774 2775 if (platform->pdata.intp_irq) 2776 destroy_workqueue(platform->workqueue); 2777 2778 if (platform->hdcp_workqueue) { 2779 cancel_delayed_work(&platform->hdcp_work); 2780 flush_workqueue(platform->hdcp_workqueue); 2781 destroy_workqueue(platform->hdcp_workqueue); 2782 } 2783 2784 if (!platform->pdata.low_power_mode) 2785 pm_runtime_put_sync_suspend(&client->dev); 2786 2787 if (platform->pdata.audio_en) 2788 anx7625_unregister_audio(platform); 2789 } 2790 2791 static const struct i2c_device_id anx7625_id[] = { 2792 {"anx7625", 0}, 2793 {} 2794 }; 2795 2796 MODULE_DEVICE_TABLE(i2c, anx7625_id); 2797 2798 static const struct of_device_id anx_match_table[] = { 2799 {.compatible = "analogix,anx7625",}, 2800 {}, 2801 }; 2802 MODULE_DEVICE_TABLE(of, anx_match_table); 2803 2804 static struct i2c_driver anx7625_driver = { 2805 .driver = { 2806 .name = "anx7625", 2807 .of_match_table = anx_match_table, 2808 .pm = &anx7625_pm_ops, 2809 }, 2810 .probe = anx7625_i2c_probe, 2811 .remove = anx7625_i2c_remove, 2812 2813 .id_table = anx7625_id, 2814 }; 2815 2816 module_i2c_driver(anx7625_driver); 2817 2818 MODULE_DESCRIPTION("MIPI2DP anx7625 driver"); 2819 MODULE_AUTHOR("Xin Ji <xji@analogixsemi.com>"); 2820 MODULE_LICENSE("GPL v2"); 2821 MODULE_VERSION(ANX7625_DRV_VERSION); 2822