1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Xilinx Zynq GPIO device driver 4 * 5 * Copyright (C) 2009 - 2014 Xilinx, Inc. 6 */ 7 8 #include <linux/bitops.h> 9 #include <linux/clk.h> 10 #include <linux/gpio/driver.h> 11 #include <linux/init.h> 12 #include <linux/interrupt.h> 13 #include <linux/spinlock.h> 14 #include <linux/io.h> 15 #include <linux/module.h> 16 #include <linux/platform_device.h> 17 #include <linux/pm_runtime.h> 18 #include <linux/of.h> 19 20 #define DRIVER_NAME "zynq-gpio" 21 22 /* Maximum banks */ 23 #define ZYNQ_GPIO_MAX_BANK 4 24 #define ZYNQMP_GPIO_MAX_BANK 6 25 #define VERSAL_GPIO_MAX_BANK 4 26 #define PMC_GPIO_MAX_BANK 5 27 #define VERSAL_UNUSED_BANKS 2 28 29 #define ZYNQ_GPIO_BANK0_NGPIO 32 30 #define ZYNQ_GPIO_BANK1_NGPIO 22 31 #define ZYNQ_GPIO_BANK2_NGPIO 32 32 #define ZYNQ_GPIO_BANK3_NGPIO 32 33 34 #define ZYNQMP_GPIO_BANK0_NGPIO 26 35 #define ZYNQMP_GPIO_BANK1_NGPIO 26 36 #define ZYNQMP_GPIO_BANK2_NGPIO 26 37 #define ZYNQMP_GPIO_BANK3_NGPIO 32 38 #define ZYNQMP_GPIO_BANK4_NGPIO 32 39 #define ZYNQMP_GPIO_BANK5_NGPIO 32 40 41 #define ZYNQ_GPIO_NR_GPIOS 118 42 #define ZYNQMP_GPIO_NR_GPIOS 174 43 44 #define ZYNQ_GPIO_BANK0_PIN_MIN(str) 0 45 #define ZYNQ_GPIO_BANK0_PIN_MAX(str) (ZYNQ_GPIO_BANK0_PIN_MIN(str) + \ 46 ZYNQ##str##_GPIO_BANK0_NGPIO - 1) 47 #define ZYNQ_GPIO_BANK1_PIN_MIN(str) (ZYNQ_GPIO_BANK0_PIN_MAX(str) + 1) 48 #define ZYNQ_GPIO_BANK1_PIN_MAX(str) (ZYNQ_GPIO_BANK1_PIN_MIN(str) + \ 49 ZYNQ##str##_GPIO_BANK1_NGPIO - 1) 50 #define ZYNQ_GPIO_BANK2_PIN_MIN(str) (ZYNQ_GPIO_BANK1_PIN_MAX(str) + 1) 51 #define ZYNQ_GPIO_BANK2_PIN_MAX(str) (ZYNQ_GPIO_BANK2_PIN_MIN(str) + \ 52 ZYNQ##str##_GPIO_BANK2_NGPIO - 1) 53 #define ZYNQ_GPIO_BANK3_PIN_MIN(str) (ZYNQ_GPIO_BANK2_PIN_MAX(str) + 1) 54 #define ZYNQ_GPIO_BANK3_PIN_MAX(str) (ZYNQ_GPIO_BANK3_PIN_MIN(str) + \ 55 ZYNQ##str##_GPIO_BANK3_NGPIO - 1) 56 #define ZYNQ_GPIO_BANK4_PIN_MIN(str) (ZYNQ_GPIO_BANK3_PIN_MAX(str) + 1) 57 #define ZYNQ_GPIO_BANK4_PIN_MAX(str) (ZYNQ_GPIO_BANK4_PIN_MIN(str) + \ 58 ZYNQ##str##_GPIO_BANK4_NGPIO - 1) 59 #define ZYNQ_GPIO_BANK5_PIN_MIN(str) (ZYNQ_GPIO_BANK4_PIN_MAX(str) + 1) 60 #define ZYNQ_GPIO_BANK5_PIN_MAX(str) (ZYNQ_GPIO_BANK5_PIN_MIN(str) + \ 61 ZYNQ##str##_GPIO_BANK5_NGPIO - 1) 62 63 /* Register offsets for the GPIO device */ 64 /* LSW Mask & Data -WO */ 65 #define ZYNQ_GPIO_DATA_LSW_OFFSET(BANK) (0x000 + (8 * BANK)) 66 /* MSW Mask & Data -WO */ 67 #define ZYNQ_GPIO_DATA_MSW_OFFSET(BANK) (0x004 + (8 * BANK)) 68 /* Data Register-RW */ 69 #define ZYNQ_GPIO_DATA_OFFSET(BANK) (0x040 + (4 * BANK)) 70 #define ZYNQ_GPIO_DATA_RO_OFFSET(BANK) (0x060 + (4 * BANK)) 71 /* Direction mode reg-RW */ 72 #define ZYNQ_GPIO_DIRM_OFFSET(BANK) (0x204 + (0x40 * BANK)) 73 /* Output enable reg-RW */ 74 #define ZYNQ_GPIO_OUTEN_OFFSET(BANK) (0x208 + (0x40 * BANK)) 75 /* Interrupt mask reg-RO */ 76 #define ZYNQ_GPIO_INTMASK_OFFSET(BANK) (0x20C + (0x40 * BANK)) 77 /* Interrupt enable reg-WO */ 78 #define ZYNQ_GPIO_INTEN_OFFSET(BANK) (0x210 + (0x40 * BANK)) 79 /* Interrupt disable reg-WO */ 80 #define ZYNQ_GPIO_INTDIS_OFFSET(BANK) (0x214 + (0x40 * BANK)) 81 /* Interrupt status reg-RO */ 82 #define ZYNQ_GPIO_INTSTS_OFFSET(BANK) (0x218 + (0x40 * BANK)) 83 /* Interrupt type reg-RW */ 84 #define ZYNQ_GPIO_INTTYPE_OFFSET(BANK) (0x21C + (0x40 * BANK)) 85 /* Interrupt polarity reg-RW */ 86 #define ZYNQ_GPIO_INTPOL_OFFSET(BANK) (0x220 + (0x40 * BANK)) 87 /* Interrupt on any, reg-RW */ 88 #define ZYNQ_GPIO_INTANY_OFFSET(BANK) (0x224 + (0x40 * BANK)) 89 90 /* Disable all interrupts mask */ 91 #define ZYNQ_GPIO_IXR_DISABLE_ALL 0xFFFFFFFF 92 93 /* Mid pin number of a bank */ 94 #define ZYNQ_GPIO_MID_PIN_NUM 16 95 96 /* GPIO upper 16 bit mask */ 97 #define ZYNQ_GPIO_UPPER_MASK 0xFFFF0000 98 99 /* set to differentiate zynq from zynqmp, 0=zynqmp, 1=zynq */ 100 #define ZYNQ_GPIO_QUIRK_IS_ZYNQ BIT(0) 101 #define GPIO_QUIRK_DATA_RO_BUG BIT(1) 102 #define GPIO_QUIRK_VERSAL BIT(2) 103 104 struct gpio_regs { 105 u32 datamsw[ZYNQMP_GPIO_MAX_BANK]; 106 u32 datalsw[ZYNQMP_GPIO_MAX_BANK]; 107 u32 dirm[ZYNQMP_GPIO_MAX_BANK]; 108 u32 outen[ZYNQMP_GPIO_MAX_BANK]; 109 u32 int_en[ZYNQMP_GPIO_MAX_BANK]; 110 u32 int_dis[ZYNQMP_GPIO_MAX_BANK]; 111 u32 int_type[ZYNQMP_GPIO_MAX_BANK]; 112 u32 int_polarity[ZYNQMP_GPIO_MAX_BANK]; 113 u32 int_any[ZYNQMP_GPIO_MAX_BANK]; 114 }; 115 116 /** 117 * struct zynq_gpio - gpio device private data structure 118 * @chip: instance of the gpio_chip 119 * @base_addr: base address of the GPIO device 120 * @clk: clock resource for this controller 121 * @irq: interrupt for the GPIO device 122 * @p_data: pointer to platform data 123 * @context: context registers 124 * @dirlock: lock used for direction in/out synchronization 125 */ 126 struct zynq_gpio { 127 struct gpio_chip chip; 128 void __iomem *base_addr; 129 struct clk *clk; 130 int irq; 131 const struct zynq_platform_data *p_data; 132 struct gpio_regs context; 133 spinlock_t dirlock; /* lock */ 134 }; 135 136 /** 137 * struct zynq_platform_data - zynq gpio platform data structure 138 * @label: string to store in gpio->label 139 * @quirks: Flags is used to identify the platform 140 * @ngpio: max number of gpio pins 141 * @max_bank: maximum number of gpio banks 142 * @bank_min: this array represents bank's min pin 143 * @bank_max: this array represents bank's max pin 144 */ 145 struct zynq_platform_data { 146 const char *label; 147 u32 quirks; 148 u16 ngpio; 149 int max_bank; 150 int bank_min[ZYNQMP_GPIO_MAX_BANK]; 151 int bank_max[ZYNQMP_GPIO_MAX_BANK]; 152 }; 153 154 static struct irq_chip zynq_gpio_level_irqchip; 155 static struct irq_chip zynq_gpio_edge_irqchip; 156 157 /** 158 * zynq_gpio_is_zynq - test if HW is zynq or zynqmp 159 * @gpio: Pointer to driver data struct 160 * 161 * Return: 0 if zynqmp, 1 if zynq. 162 */ 163 static int zynq_gpio_is_zynq(struct zynq_gpio *gpio) 164 { 165 return !!(gpio->p_data->quirks & ZYNQ_GPIO_QUIRK_IS_ZYNQ); 166 } 167 168 /** 169 * gpio_data_ro_bug - test if HW bug exists or not 170 * @gpio: Pointer to driver data struct 171 * 172 * Return: 0 if bug doesnot exist, 1 if bug exists. 173 */ 174 static int gpio_data_ro_bug(struct zynq_gpio *gpio) 175 { 176 return !!(gpio->p_data->quirks & GPIO_QUIRK_DATA_RO_BUG); 177 } 178 179 /** 180 * zynq_gpio_get_bank_pin - Get the bank number and pin number within that bank 181 * for a given pin in the GPIO device 182 * @pin_num: gpio pin number within the device 183 * @bank_num: an output parameter used to return the bank number of the gpio 184 * pin 185 * @bank_pin_num: an output parameter used to return pin number within a bank 186 * for the given gpio pin 187 * @gpio: gpio device data structure 188 * 189 * Returns the bank number and pin offset within the bank. 190 */ 191 static inline void zynq_gpio_get_bank_pin(unsigned int pin_num, 192 unsigned int *bank_num, 193 unsigned int *bank_pin_num, 194 struct zynq_gpio *gpio) 195 { 196 int bank; 197 198 for (bank = 0; bank < gpio->p_data->max_bank; bank++) { 199 if ((pin_num >= gpio->p_data->bank_min[bank]) && 200 (pin_num <= gpio->p_data->bank_max[bank])) { 201 *bank_num = bank; 202 *bank_pin_num = pin_num - 203 gpio->p_data->bank_min[bank]; 204 return; 205 } 206 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL) 207 bank = bank + VERSAL_UNUSED_BANKS; 208 } 209 210 /* default */ 211 WARN(true, "invalid GPIO pin number: %u", pin_num); 212 *bank_num = 0; 213 *bank_pin_num = 0; 214 } 215 216 /** 217 * zynq_gpio_get_value - Get the state of the specified pin of GPIO device 218 * @chip: gpio_chip instance to be worked on 219 * @pin: gpio pin number within the device 220 * 221 * This function reads the state of the specified pin of the GPIO device. 222 * 223 * Return: 0 if the pin is low, 1 if pin is high. 224 */ 225 static int zynq_gpio_get_value(struct gpio_chip *chip, unsigned int pin) 226 { 227 u32 data; 228 unsigned int bank_num, bank_pin_num; 229 struct zynq_gpio *gpio = gpiochip_get_data(chip); 230 231 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); 232 233 if (gpio_data_ro_bug(gpio)) { 234 if (zynq_gpio_is_zynq(gpio)) { 235 if (bank_num <= 1) { 236 data = readl_relaxed(gpio->base_addr + 237 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num)); 238 } else { 239 data = readl_relaxed(gpio->base_addr + 240 ZYNQ_GPIO_DATA_OFFSET(bank_num)); 241 } 242 } else { 243 if (bank_num <= 2) { 244 data = readl_relaxed(gpio->base_addr + 245 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num)); 246 } else { 247 data = readl_relaxed(gpio->base_addr + 248 ZYNQ_GPIO_DATA_OFFSET(bank_num)); 249 } 250 } 251 } else { 252 data = readl_relaxed(gpio->base_addr + 253 ZYNQ_GPIO_DATA_RO_OFFSET(bank_num)); 254 } 255 return (data >> bank_pin_num) & 1; 256 } 257 258 /** 259 * zynq_gpio_set_value - Modify the state of the pin with specified value 260 * @chip: gpio_chip instance to be worked on 261 * @pin: gpio pin number within the device 262 * @state: value used to modify the state of the specified pin 263 * 264 * This function calculates the register offset (i.e to lower 16 bits or 265 * upper 16 bits) based on the given pin number and sets the state of a 266 * gpio pin to the specified value. The state is either 0 or non-zero. 267 */ 268 static void zynq_gpio_set_value(struct gpio_chip *chip, unsigned int pin, 269 int state) 270 { 271 unsigned int reg_offset, bank_num, bank_pin_num; 272 struct zynq_gpio *gpio = gpiochip_get_data(chip); 273 274 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); 275 276 if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) { 277 /* only 16 data bits in bit maskable reg */ 278 bank_pin_num -= ZYNQ_GPIO_MID_PIN_NUM; 279 reg_offset = ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num); 280 } else { 281 reg_offset = ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num); 282 } 283 284 /* 285 * get the 32 bit value to be written to the mask/data register where 286 * the upper 16 bits is the mask and lower 16 bits is the data 287 */ 288 state = !!state; 289 state = ~(1 << (bank_pin_num + ZYNQ_GPIO_MID_PIN_NUM)) & 290 ((state << bank_pin_num) | ZYNQ_GPIO_UPPER_MASK); 291 292 writel_relaxed(state, gpio->base_addr + reg_offset); 293 } 294 295 /** 296 * zynq_gpio_dir_in - Set the direction of the specified GPIO pin as input 297 * @chip: gpio_chip instance to be worked on 298 * @pin: gpio pin number within the device 299 * 300 * This function uses the read-modify-write sequence to set the direction of 301 * the gpio pin as input. 302 * 303 * Return: 0 always 304 */ 305 static int zynq_gpio_dir_in(struct gpio_chip *chip, unsigned int pin) 306 { 307 u32 reg; 308 unsigned int bank_num, bank_pin_num; 309 unsigned long flags; 310 struct zynq_gpio *gpio = gpiochip_get_data(chip); 311 312 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); 313 314 /* 315 * On zynq bank 0 pins 7 and 8 are special and cannot be used 316 * as inputs. 317 */ 318 if (zynq_gpio_is_zynq(gpio) && bank_num == 0 && 319 (bank_pin_num == 7 || bank_pin_num == 8)) 320 return -EINVAL; 321 322 /* clear the bit in direction mode reg to set the pin as input */ 323 spin_lock_irqsave(&gpio->dirlock, flags); 324 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 325 reg &= ~BIT(bank_pin_num); 326 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 327 spin_unlock_irqrestore(&gpio->dirlock, flags); 328 329 return 0; 330 } 331 332 /** 333 * zynq_gpio_dir_out - Set the direction of the specified GPIO pin as output 334 * @chip: gpio_chip instance to be worked on 335 * @pin: gpio pin number within the device 336 * @state: value to be written to specified pin 337 * 338 * This function sets the direction of specified GPIO pin as output, configures 339 * the Output Enable register for the pin and uses zynq_gpio_set to set 340 * the state of the pin to the value specified. 341 * 342 * Return: 0 always 343 */ 344 static int zynq_gpio_dir_out(struct gpio_chip *chip, unsigned int pin, 345 int state) 346 { 347 u32 reg; 348 unsigned int bank_num, bank_pin_num; 349 unsigned long flags; 350 struct zynq_gpio *gpio = gpiochip_get_data(chip); 351 352 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); 353 354 /* set the GPIO pin as output */ 355 spin_lock_irqsave(&gpio->dirlock, flags); 356 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 357 reg |= BIT(bank_pin_num); 358 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 359 360 /* configure the output enable reg for the pin */ 361 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num)); 362 reg |= BIT(bank_pin_num); 363 writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num)); 364 spin_unlock_irqrestore(&gpio->dirlock, flags); 365 366 /* set the state of the pin */ 367 zynq_gpio_set_value(chip, pin, state); 368 return 0; 369 } 370 371 /** 372 * zynq_gpio_get_direction - Read the direction of the specified GPIO pin 373 * @chip: gpio_chip instance to be worked on 374 * @pin: gpio pin number within the device 375 * 376 * This function returns the direction of the specified GPIO. 377 * 378 * Return: GPIO_LINE_DIRECTION_OUT or GPIO_LINE_DIRECTION_IN 379 */ 380 static int zynq_gpio_get_direction(struct gpio_chip *chip, unsigned int pin) 381 { 382 u32 reg; 383 unsigned int bank_num, bank_pin_num; 384 struct zynq_gpio *gpio = gpiochip_get_data(chip); 385 386 zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); 387 388 reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 389 390 if (reg & BIT(bank_pin_num)) 391 return GPIO_LINE_DIRECTION_OUT; 392 393 return GPIO_LINE_DIRECTION_IN; 394 } 395 396 /** 397 * zynq_gpio_irq_mask - Disable the interrupts for a gpio pin 398 * @irq_data: per irq and chip data passed down to chip functions 399 * 400 * This function calculates gpio pin number from irq number and sets the 401 * bit in the Interrupt Disable register of the corresponding bank to disable 402 * interrupts for that pin. 403 */ 404 static void zynq_gpio_irq_mask(struct irq_data *irq_data) 405 { 406 unsigned int device_pin_num, bank_num, bank_pin_num; 407 struct zynq_gpio *gpio = 408 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data)); 409 410 device_pin_num = irq_data->hwirq; 411 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); 412 writel_relaxed(BIT(bank_pin_num), 413 gpio->base_addr + ZYNQ_GPIO_INTDIS_OFFSET(bank_num)); 414 } 415 416 /** 417 * zynq_gpio_irq_unmask - Enable the interrupts for a gpio pin 418 * @irq_data: irq data containing irq number of gpio pin for the interrupt 419 * to enable 420 * 421 * This function calculates the gpio pin number from irq number and sets the 422 * bit in the Interrupt Enable register of the corresponding bank to enable 423 * interrupts for that pin. 424 */ 425 static void zynq_gpio_irq_unmask(struct irq_data *irq_data) 426 { 427 unsigned int device_pin_num, bank_num, bank_pin_num; 428 struct zynq_gpio *gpio = 429 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data)); 430 431 device_pin_num = irq_data->hwirq; 432 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); 433 writel_relaxed(BIT(bank_pin_num), 434 gpio->base_addr + ZYNQ_GPIO_INTEN_OFFSET(bank_num)); 435 } 436 437 /** 438 * zynq_gpio_irq_ack - Acknowledge the interrupt of a gpio pin 439 * @irq_data: irq data containing irq number of gpio pin for the interrupt 440 * to ack 441 * 442 * This function calculates gpio pin number from irq number and sets the bit 443 * in the Interrupt Status Register of the corresponding bank, to ACK the irq. 444 */ 445 static void zynq_gpio_irq_ack(struct irq_data *irq_data) 446 { 447 unsigned int device_pin_num, bank_num, bank_pin_num; 448 struct zynq_gpio *gpio = 449 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data)); 450 451 device_pin_num = irq_data->hwirq; 452 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); 453 writel_relaxed(BIT(bank_pin_num), 454 gpio->base_addr + ZYNQ_GPIO_INTSTS_OFFSET(bank_num)); 455 } 456 457 /** 458 * zynq_gpio_irq_enable - Enable the interrupts for a gpio pin 459 * @irq_data: irq data containing irq number of gpio pin for the interrupt 460 * to enable 461 * 462 * Clears the INTSTS bit and unmasks the given interrupt. 463 */ 464 static void zynq_gpio_irq_enable(struct irq_data *irq_data) 465 { 466 /* 467 * The Zynq GPIO controller does not disable interrupt detection when 468 * the interrupt is masked and only disables the propagation of the 469 * interrupt. This means when the controller detects an interrupt 470 * condition while the interrupt is logically disabled it will propagate 471 * that interrupt event once the interrupt is enabled. This will cause 472 * the interrupt consumer to see spurious interrupts to prevent this 473 * first make sure that the interrupt is not asserted and then enable 474 * it. 475 */ 476 zynq_gpio_irq_ack(irq_data); 477 zynq_gpio_irq_unmask(irq_data); 478 } 479 480 /** 481 * zynq_gpio_set_irq_type - Set the irq type for a gpio pin 482 * @irq_data: irq data containing irq number of gpio pin 483 * @type: interrupt type that is to be set for the gpio pin 484 * 485 * This function gets the gpio pin number and its bank from the gpio pin number 486 * and configures the INT_TYPE, INT_POLARITY and INT_ANY registers. 487 * 488 * Return: 0, negative error otherwise. 489 * TYPE-EDGE_RISING, INT_TYPE - 1, INT_POLARITY - 1, INT_ANY - 0; 490 * TYPE-EDGE_FALLING, INT_TYPE - 1, INT_POLARITY - 0, INT_ANY - 0; 491 * TYPE-EDGE_BOTH, INT_TYPE - 1, INT_POLARITY - NA, INT_ANY - 1; 492 * TYPE-LEVEL_HIGH, INT_TYPE - 0, INT_POLARITY - 1, INT_ANY - NA; 493 * TYPE-LEVEL_LOW, INT_TYPE - 0, INT_POLARITY - 0, INT_ANY - NA 494 */ 495 static int zynq_gpio_set_irq_type(struct irq_data *irq_data, unsigned int type) 496 { 497 u32 int_type, int_pol, int_any; 498 unsigned int device_pin_num, bank_num, bank_pin_num; 499 struct zynq_gpio *gpio = 500 gpiochip_get_data(irq_data_get_irq_chip_data(irq_data)); 501 502 device_pin_num = irq_data->hwirq; 503 zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); 504 505 int_type = readl_relaxed(gpio->base_addr + 506 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num)); 507 int_pol = readl_relaxed(gpio->base_addr + 508 ZYNQ_GPIO_INTPOL_OFFSET(bank_num)); 509 int_any = readl_relaxed(gpio->base_addr + 510 ZYNQ_GPIO_INTANY_OFFSET(bank_num)); 511 512 /* 513 * based on the type requested, configure the INT_TYPE, INT_POLARITY 514 * and INT_ANY registers 515 */ 516 switch (type) { 517 case IRQ_TYPE_EDGE_RISING: 518 int_type |= BIT(bank_pin_num); 519 int_pol |= BIT(bank_pin_num); 520 int_any &= ~BIT(bank_pin_num); 521 break; 522 case IRQ_TYPE_EDGE_FALLING: 523 int_type |= BIT(bank_pin_num); 524 int_pol &= ~BIT(bank_pin_num); 525 int_any &= ~BIT(bank_pin_num); 526 break; 527 case IRQ_TYPE_EDGE_BOTH: 528 int_type |= BIT(bank_pin_num); 529 int_any |= BIT(bank_pin_num); 530 break; 531 case IRQ_TYPE_LEVEL_HIGH: 532 int_type &= ~BIT(bank_pin_num); 533 int_pol |= BIT(bank_pin_num); 534 break; 535 case IRQ_TYPE_LEVEL_LOW: 536 int_type &= ~BIT(bank_pin_num); 537 int_pol &= ~BIT(bank_pin_num); 538 break; 539 default: 540 return -EINVAL; 541 } 542 543 writel_relaxed(int_type, 544 gpio->base_addr + ZYNQ_GPIO_INTTYPE_OFFSET(bank_num)); 545 writel_relaxed(int_pol, 546 gpio->base_addr + ZYNQ_GPIO_INTPOL_OFFSET(bank_num)); 547 writel_relaxed(int_any, 548 gpio->base_addr + ZYNQ_GPIO_INTANY_OFFSET(bank_num)); 549 550 if (type & IRQ_TYPE_LEVEL_MASK) 551 irq_set_chip_handler_name_locked(irq_data, 552 &zynq_gpio_level_irqchip, 553 handle_fasteoi_irq, NULL); 554 else 555 irq_set_chip_handler_name_locked(irq_data, 556 &zynq_gpio_edge_irqchip, 557 handle_level_irq, NULL); 558 559 return 0; 560 } 561 562 static int zynq_gpio_set_wake(struct irq_data *data, unsigned int on) 563 { 564 struct zynq_gpio *gpio = 565 gpiochip_get_data(irq_data_get_irq_chip_data(data)); 566 567 irq_set_irq_wake(gpio->irq, on); 568 569 return 0; 570 } 571 572 static int zynq_gpio_irq_reqres(struct irq_data *d) 573 { 574 struct gpio_chip *chip = irq_data_get_irq_chip_data(d); 575 int ret; 576 577 ret = pm_runtime_resume_and_get(chip->parent); 578 if (ret < 0) 579 return ret; 580 581 return gpiochip_reqres_irq(chip, d->hwirq); 582 } 583 584 static void zynq_gpio_irq_relres(struct irq_data *d) 585 { 586 struct gpio_chip *chip = irq_data_get_irq_chip_data(d); 587 588 gpiochip_relres_irq(chip, d->hwirq); 589 pm_runtime_put(chip->parent); 590 } 591 592 /* irq chip descriptor */ 593 static struct irq_chip zynq_gpio_level_irqchip = { 594 .name = DRIVER_NAME, 595 .irq_enable = zynq_gpio_irq_enable, 596 .irq_eoi = zynq_gpio_irq_ack, 597 .irq_mask = zynq_gpio_irq_mask, 598 .irq_unmask = zynq_gpio_irq_unmask, 599 .irq_set_type = zynq_gpio_set_irq_type, 600 .irq_set_wake = zynq_gpio_set_wake, 601 .irq_request_resources = zynq_gpio_irq_reqres, 602 .irq_release_resources = zynq_gpio_irq_relres, 603 .flags = IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED | 604 IRQCHIP_MASK_ON_SUSPEND, 605 }; 606 607 static struct irq_chip zynq_gpio_edge_irqchip = { 608 .name = DRIVER_NAME, 609 .irq_enable = zynq_gpio_irq_enable, 610 .irq_ack = zynq_gpio_irq_ack, 611 .irq_mask = zynq_gpio_irq_mask, 612 .irq_unmask = zynq_gpio_irq_unmask, 613 .irq_set_type = zynq_gpio_set_irq_type, 614 .irq_set_wake = zynq_gpio_set_wake, 615 .irq_request_resources = zynq_gpio_irq_reqres, 616 .irq_release_resources = zynq_gpio_irq_relres, 617 .flags = IRQCHIP_MASK_ON_SUSPEND, 618 }; 619 620 static void zynq_gpio_handle_bank_irq(struct zynq_gpio *gpio, 621 unsigned int bank_num, 622 unsigned long pending) 623 { 624 unsigned int bank_offset = gpio->p_data->bank_min[bank_num]; 625 struct irq_domain *irqdomain = gpio->chip.irq.domain; 626 int offset; 627 628 if (!pending) 629 return; 630 631 for_each_set_bit(offset, &pending, 32) { 632 unsigned int gpio_irq; 633 634 gpio_irq = irq_find_mapping(irqdomain, offset + bank_offset); 635 generic_handle_irq(gpio_irq); 636 } 637 } 638 639 /** 640 * zynq_gpio_irqhandler - IRQ handler for the gpio banks of a gpio device 641 * @desc: irq descriptor instance of the 'irq' 642 * 643 * This function reads the Interrupt Status Register of each bank to get the 644 * gpio pin number which has triggered an interrupt. It then acks the triggered 645 * interrupt and calls the pin specific handler set by the higher layer 646 * application for that pin. 647 * Note: A bug is reported if no handler is set for the gpio pin. 648 */ 649 static void zynq_gpio_irqhandler(struct irq_desc *desc) 650 { 651 u32 int_sts, int_enb; 652 unsigned int bank_num; 653 struct zynq_gpio *gpio = 654 gpiochip_get_data(irq_desc_get_handler_data(desc)); 655 struct irq_chip *irqchip = irq_desc_get_chip(desc); 656 657 chained_irq_enter(irqchip, desc); 658 659 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) { 660 int_sts = readl_relaxed(gpio->base_addr + 661 ZYNQ_GPIO_INTSTS_OFFSET(bank_num)); 662 int_enb = readl_relaxed(gpio->base_addr + 663 ZYNQ_GPIO_INTMASK_OFFSET(bank_num)); 664 zynq_gpio_handle_bank_irq(gpio, bank_num, int_sts & ~int_enb); 665 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL) 666 bank_num = bank_num + VERSAL_UNUSED_BANKS; 667 } 668 669 chained_irq_exit(irqchip, desc); 670 } 671 672 static void zynq_gpio_save_context(struct zynq_gpio *gpio) 673 { 674 unsigned int bank_num; 675 676 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) { 677 gpio->context.datalsw[bank_num] = 678 readl_relaxed(gpio->base_addr + 679 ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num)); 680 gpio->context.datamsw[bank_num] = 681 readl_relaxed(gpio->base_addr + 682 ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num)); 683 gpio->context.dirm[bank_num] = readl_relaxed(gpio->base_addr + 684 ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 685 gpio->context.int_en[bank_num] = readl_relaxed(gpio->base_addr + 686 ZYNQ_GPIO_INTMASK_OFFSET(bank_num)); 687 gpio->context.int_type[bank_num] = 688 readl_relaxed(gpio->base_addr + 689 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num)); 690 gpio->context.int_polarity[bank_num] = 691 readl_relaxed(gpio->base_addr + 692 ZYNQ_GPIO_INTPOL_OFFSET(bank_num)); 693 gpio->context.int_any[bank_num] = 694 readl_relaxed(gpio->base_addr + 695 ZYNQ_GPIO_INTANY_OFFSET(bank_num)); 696 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL) 697 bank_num = bank_num + VERSAL_UNUSED_BANKS; 698 } 699 } 700 701 static void zynq_gpio_restore_context(struct zynq_gpio *gpio) 702 { 703 unsigned int bank_num; 704 705 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) { 706 writel_relaxed(ZYNQ_GPIO_IXR_DISABLE_ALL, gpio->base_addr + 707 ZYNQ_GPIO_INTDIS_OFFSET(bank_num)); 708 writel_relaxed(gpio->context.datalsw[bank_num], 709 gpio->base_addr + 710 ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num)); 711 writel_relaxed(gpio->context.datamsw[bank_num], 712 gpio->base_addr + 713 ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num)); 714 writel_relaxed(gpio->context.dirm[bank_num], 715 gpio->base_addr + 716 ZYNQ_GPIO_DIRM_OFFSET(bank_num)); 717 writel_relaxed(gpio->context.int_type[bank_num], 718 gpio->base_addr + 719 ZYNQ_GPIO_INTTYPE_OFFSET(bank_num)); 720 writel_relaxed(gpio->context.int_polarity[bank_num], 721 gpio->base_addr + 722 ZYNQ_GPIO_INTPOL_OFFSET(bank_num)); 723 writel_relaxed(gpio->context.int_any[bank_num], 724 gpio->base_addr + 725 ZYNQ_GPIO_INTANY_OFFSET(bank_num)); 726 writel_relaxed(~(gpio->context.int_en[bank_num]), 727 gpio->base_addr + 728 ZYNQ_GPIO_INTEN_OFFSET(bank_num)); 729 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL) 730 bank_num = bank_num + VERSAL_UNUSED_BANKS; 731 } 732 } 733 734 static int __maybe_unused zynq_gpio_suspend(struct device *dev) 735 { 736 struct zynq_gpio *gpio = dev_get_drvdata(dev); 737 struct irq_data *data = irq_get_irq_data(gpio->irq); 738 739 if (!device_may_wakeup(dev)) 740 disable_irq(gpio->irq); 741 742 if (!irqd_is_wakeup_set(data)) { 743 zynq_gpio_save_context(gpio); 744 return pm_runtime_force_suspend(dev); 745 } 746 747 return 0; 748 } 749 750 static int __maybe_unused zynq_gpio_resume(struct device *dev) 751 { 752 struct zynq_gpio *gpio = dev_get_drvdata(dev); 753 struct irq_data *data = irq_get_irq_data(gpio->irq); 754 int ret; 755 756 if (!device_may_wakeup(dev)) 757 enable_irq(gpio->irq); 758 759 if (!irqd_is_wakeup_set(data)) { 760 ret = pm_runtime_force_resume(dev); 761 zynq_gpio_restore_context(gpio); 762 return ret; 763 } 764 765 return 0; 766 } 767 768 static int __maybe_unused zynq_gpio_runtime_suspend(struct device *dev) 769 { 770 struct zynq_gpio *gpio = dev_get_drvdata(dev); 771 772 clk_disable_unprepare(gpio->clk); 773 774 return 0; 775 } 776 777 static int __maybe_unused zynq_gpio_runtime_resume(struct device *dev) 778 { 779 struct zynq_gpio *gpio = dev_get_drvdata(dev); 780 781 return clk_prepare_enable(gpio->clk); 782 } 783 784 static int zynq_gpio_request(struct gpio_chip *chip, unsigned int offset) 785 { 786 int ret; 787 788 ret = pm_runtime_get_sync(chip->parent); 789 790 /* 791 * If the device is already active pm_runtime_get() will return 1 on 792 * success, but gpio_request still needs to return 0. 793 */ 794 return ret < 0 ? ret : 0; 795 } 796 797 static void zynq_gpio_free(struct gpio_chip *chip, unsigned int offset) 798 { 799 pm_runtime_put(chip->parent); 800 } 801 802 static const struct dev_pm_ops zynq_gpio_dev_pm_ops = { 803 SET_SYSTEM_SLEEP_PM_OPS(zynq_gpio_suspend, zynq_gpio_resume) 804 SET_RUNTIME_PM_OPS(zynq_gpio_runtime_suspend, 805 zynq_gpio_runtime_resume, NULL) 806 }; 807 808 static const struct zynq_platform_data versal_gpio_def = { 809 .label = "versal_gpio", 810 .quirks = GPIO_QUIRK_VERSAL, 811 .ngpio = 58, 812 .max_bank = VERSAL_GPIO_MAX_BANK, 813 .bank_min[0] = 0, 814 .bank_max[0] = 25, /* 0 to 25 are connected to MIOs (26 pins) */ 815 .bank_min[3] = 26, 816 .bank_max[3] = 57, /* Bank 3 is connected to FMIOs (32 pins) */ 817 }; 818 819 static const struct zynq_platform_data pmc_gpio_def = { 820 .label = "pmc_gpio", 821 .ngpio = 116, 822 .max_bank = PMC_GPIO_MAX_BANK, 823 .bank_min[0] = 0, 824 .bank_max[0] = 25, /* 0 to 25 are connected to MIOs (26 pins) */ 825 .bank_min[1] = 26, 826 .bank_max[1] = 51, /* Bank 1 are connected to MIOs (26 pins) */ 827 .bank_min[3] = 52, 828 .bank_max[3] = 83, /* Bank 3 is connected to EMIOs (32 pins) */ 829 .bank_min[4] = 84, 830 .bank_max[4] = 115, /* Bank 4 is connected to EMIOs (32 pins) */ 831 }; 832 833 static const struct zynq_platform_data zynqmp_gpio_def = { 834 .label = "zynqmp_gpio", 835 .quirks = GPIO_QUIRK_DATA_RO_BUG, 836 .ngpio = ZYNQMP_GPIO_NR_GPIOS, 837 .max_bank = ZYNQMP_GPIO_MAX_BANK, 838 .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(MP), 839 .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(MP), 840 .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(MP), 841 .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(MP), 842 .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(MP), 843 .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(MP), 844 .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(MP), 845 .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(MP), 846 .bank_min[4] = ZYNQ_GPIO_BANK4_PIN_MIN(MP), 847 .bank_max[4] = ZYNQ_GPIO_BANK4_PIN_MAX(MP), 848 .bank_min[5] = ZYNQ_GPIO_BANK5_PIN_MIN(MP), 849 .bank_max[5] = ZYNQ_GPIO_BANK5_PIN_MAX(MP), 850 }; 851 852 static const struct zynq_platform_data zynq_gpio_def = { 853 .label = "zynq_gpio", 854 .quirks = ZYNQ_GPIO_QUIRK_IS_ZYNQ | GPIO_QUIRK_DATA_RO_BUG, 855 .ngpio = ZYNQ_GPIO_NR_GPIOS, 856 .max_bank = ZYNQ_GPIO_MAX_BANK, 857 .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(), 858 .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(), 859 .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(), 860 .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(), 861 .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(), 862 .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(), 863 .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(), 864 .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(), 865 }; 866 867 static const struct of_device_id zynq_gpio_of_match[] = { 868 { .compatible = "xlnx,zynq-gpio-1.0", .data = &zynq_gpio_def }, 869 { .compatible = "xlnx,zynqmp-gpio-1.0", .data = &zynqmp_gpio_def }, 870 { .compatible = "xlnx,versal-gpio-1.0", .data = &versal_gpio_def }, 871 { .compatible = "xlnx,pmc-gpio-1.0", .data = &pmc_gpio_def }, 872 { /* end of table */ } 873 }; 874 MODULE_DEVICE_TABLE(of, zynq_gpio_of_match); 875 876 /** 877 * zynq_gpio_probe - Initialization method for a zynq_gpio device 878 * @pdev: platform device instance 879 * 880 * This function allocates memory resources for the gpio device and registers 881 * all the banks of the device. It will also set up interrupts for the gpio 882 * pins. 883 * Note: Interrupts are disabled for all the banks during initialization. 884 * 885 * Return: 0 on success, negative error otherwise. 886 */ 887 static int zynq_gpio_probe(struct platform_device *pdev) 888 { 889 int ret, bank_num; 890 struct zynq_gpio *gpio; 891 struct gpio_chip *chip; 892 struct gpio_irq_chip *girq; 893 const struct of_device_id *match; 894 895 gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL); 896 if (!gpio) 897 return -ENOMEM; 898 899 match = of_match_node(zynq_gpio_of_match, pdev->dev.of_node); 900 if (!match) { 901 dev_err(&pdev->dev, "of_match_node() failed\n"); 902 return -EINVAL; 903 } 904 gpio->p_data = match->data; 905 platform_set_drvdata(pdev, gpio); 906 907 gpio->base_addr = devm_platform_ioremap_resource(pdev, 0); 908 if (IS_ERR(gpio->base_addr)) 909 return PTR_ERR(gpio->base_addr); 910 911 gpio->irq = platform_get_irq(pdev, 0); 912 if (gpio->irq < 0) 913 return gpio->irq; 914 915 /* configure the gpio chip */ 916 chip = &gpio->chip; 917 chip->label = gpio->p_data->label; 918 chip->owner = THIS_MODULE; 919 chip->parent = &pdev->dev; 920 chip->get = zynq_gpio_get_value; 921 chip->set = zynq_gpio_set_value; 922 chip->request = zynq_gpio_request; 923 chip->free = zynq_gpio_free; 924 chip->direction_input = zynq_gpio_dir_in; 925 chip->direction_output = zynq_gpio_dir_out; 926 chip->get_direction = zynq_gpio_get_direction; 927 chip->base = of_alias_get_id(pdev->dev.of_node, "gpio"); 928 chip->ngpio = gpio->p_data->ngpio; 929 930 /* Retrieve GPIO clock */ 931 gpio->clk = devm_clk_get(&pdev->dev, NULL); 932 if (IS_ERR(gpio->clk)) 933 return dev_err_probe(&pdev->dev, PTR_ERR(gpio->clk), "input clock not found.\n"); 934 935 ret = clk_prepare_enable(gpio->clk); 936 if (ret) { 937 dev_err(&pdev->dev, "Unable to enable clock.\n"); 938 return ret; 939 } 940 941 spin_lock_init(&gpio->dirlock); 942 943 pm_runtime_set_active(&pdev->dev); 944 pm_runtime_enable(&pdev->dev); 945 ret = pm_runtime_resume_and_get(&pdev->dev); 946 if (ret < 0) 947 goto err_pm_dis; 948 949 /* disable interrupts for all banks */ 950 for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) { 951 writel_relaxed(ZYNQ_GPIO_IXR_DISABLE_ALL, gpio->base_addr + 952 ZYNQ_GPIO_INTDIS_OFFSET(bank_num)); 953 if (gpio->p_data->quirks & GPIO_QUIRK_VERSAL) 954 bank_num = bank_num + VERSAL_UNUSED_BANKS; 955 } 956 957 /* Set up the GPIO irqchip */ 958 girq = &chip->irq; 959 girq->chip = &zynq_gpio_edge_irqchip; 960 girq->parent_handler = zynq_gpio_irqhandler; 961 girq->num_parents = 1; 962 girq->parents = devm_kcalloc(&pdev->dev, 1, 963 sizeof(*girq->parents), 964 GFP_KERNEL); 965 if (!girq->parents) { 966 ret = -ENOMEM; 967 goto err_pm_put; 968 } 969 girq->parents[0] = gpio->irq; 970 girq->default_type = IRQ_TYPE_NONE; 971 girq->handler = handle_level_irq; 972 973 /* report a bug if gpio chip registration fails */ 974 ret = gpiochip_add_data(chip, gpio); 975 if (ret) { 976 dev_err(&pdev->dev, "Failed to add gpio chip\n"); 977 goto err_pm_put; 978 } 979 980 irq_set_status_flags(gpio->irq, IRQ_DISABLE_UNLAZY); 981 device_init_wakeup(&pdev->dev, 1); 982 pm_runtime_put(&pdev->dev); 983 984 return 0; 985 986 err_pm_put: 987 pm_runtime_put(&pdev->dev); 988 err_pm_dis: 989 pm_runtime_disable(&pdev->dev); 990 clk_disable_unprepare(gpio->clk); 991 992 return ret; 993 } 994 995 /** 996 * zynq_gpio_remove - Driver removal function 997 * @pdev: platform device instance 998 * 999 * Return: 0 always 1000 */ 1001 static int zynq_gpio_remove(struct platform_device *pdev) 1002 { 1003 struct zynq_gpio *gpio = platform_get_drvdata(pdev); 1004 1005 pm_runtime_get_sync(&pdev->dev); 1006 gpiochip_remove(&gpio->chip); 1007 clk_disable_unprepare(gpio->clk); 1008 device_set_wakeup_capable(&pdev->dev, 0); 1009 pm_runtime_disable(&pdev->dev); 1010 return 0; 1011 } 1012 1013 static struct platform_driver zynq_gpio_driver = { 1014 .driver = { 1015 .name = DRIVER_NAME, 1016 .pm = &zynq_gpio_dev_pm_ops, 1017 .of_match_table = zynq_gpio_of_match, 1018 }, 1019 .probe = zynq_gpio_probe, 1020 .remove = zynq_gpio_remove, 1021 }; 1022 1023 /** 1024 * zynq_gpio_init - Initial driver registration call 1025 * 1026 * Return: value from platform_driver_register 1027 */ 1028 static int __init zynq_gpio_init(void) 1029 { 1030 return platform_driver_register(&zynq_gpio_driver); 1031 } 1032 postcore_initcall(zynq_gpio_init); 1033 1034 static void __exit zynq_gpio_exit(void) 1035 { 1036 platform_driver_unregister(&zynq_gpio_driver); 1037 } 1038 module_exit(zynq_gpio_exit); 1039 1040 MODULE_AUTHOR("Xilinx Inc."); 1041 MODULE_DESCRIPTION("Zynq GPIO driver"); 1042 MODULE_LICENSE("GPL"); 1043