xref: /openbmc/linux/drivers/gpio/gpio-xilinx.c (revision 45cc35e8)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  * Xilinx gpio driver for xps/axi_gpio IP.
4  *
5  * Copyright 2008 - 2013 Xilinx, Inc.
6  */
7 
8 #include <linux/bitmap.h>
9 #include <linux/bitops.h>
10 #include <linux/clk.h>
11 #include <linux/errno.h>
12 #include <linux/gpio/driver.h>
13 #include <linux/init.h>
14 #include <linux/interrupt.h>
15 #include <linux/io.h>
16 #include <linux/irq.h>
17 #include <linux/module.h>
18 #include <linux/of_device.h>
19 #include <linux/of_platform.h>
20 #include <linux/pm_runtime.h>
21 #include <linux/slab.h>
22 
23 /* Register Offset Definitions */
24 #define XGPIO_DATA_OFFSET   (0x0)	/* Data register  */
25 #define XGPIO_TRI_OFFSET    (0x4)	/* I/O direction register  */
26 
27 #define XGPIO_CHANNEL0_OFFSET	0x0
28 #define XGPIO_CHANNEL1_OFFSET	0x8
29 
30 #define XGPIO_GIER_OFFSET	0x11c /* Global Interrupt Enable */
31 #define XGPIO_GIER_IE		BIT(31)
32 #define XGPIO_IPISR_OFFSET	0x120 /* IP Interrupt Status */
33 #define XGPIO_IPIER_OFFSET	0x128 /* IP Interrupt Enable */
34 
35 /* Read/Write access to the GPIO registers */
36 #if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_X86)
37 # define xgpio_readreg(offset)		readl(offset)
38 # define xgpio_writereg(offset, val)	writel(val, offset)
39 #else
40 # define xgpio_readreg(offset)		__raw_readl(offset)
41 # define xgpio_writereg(offset, val)	__raw_writel(val, offset)
42 #endif
43 
44 /**
45  * struct xgpio_instance - Stores information about GPIO device
46  * @gc: GPIO chip
47  * @regs: register block
48  * @hw_map: GPIO pin mapping on hardware side
49  * @sw_map: GPIO pin mapping on software side
50  * @state: GPIO write state shadow register
51  * @last_irq_read: GPIO read state register from last interrupt
52  * @dir: GPIO direction shadow register
53  * @gpio_lock: Lock used for synchronization
54  * @irq: IRQ used by GPIO device
55  * @irqchip: IRQ chip
56  * @enable: GPIO IRQ enable/disable bitfield
57  * @rising_edge: GPIO IRQ rising edge enable/disable bitfield
58  * @falling_edge: GPIO IRQ falling edge enable/disable bitfield
59  * @clk: clock resource for this driver
60  */
61 struct xgpio_instance {
62 	struct gpio_chip gc;
63 	void __iomem *regs;
64 	DECLARE_BITMAP(hw_map, 64);
65 	DECLARE_BITMAP(sw_map, 64);
66 	DECLARE_BITMAP(state, 64);
67 	DECLARE_BITMAP(last_irq_read, 64);
68 	DECLARE_BITMAP(dir, 64);
69 	spinlock_t gpio_lock;	/* For serializing operations */
70 	int irq;
71 	struct irq_chip irqchip;
72 	DECLARE_BITMAP(enable, 64);
73 	DECLARE_BITMAP(rising_edge, 64);
74 	DECLARE_BITMAP(falling_edge, 64);
75 	struct clk *clk;
76 };
77 
78 static inline int xgpio_from_bit(struct xgpio_instance *chip, int bit)
79 {
80 	return bitmap_bitremap(bit, chip->hw_map, chip->sw_map, 64);
81 }
82 
83 static inline int xgpio_to_bit(struct xgpio_instance *chip, int gpio)
84 {
85 	return bitmap_bitremap(gpio, chip->sw_map, chip->hw_map, 64);
86 }
87 
88 static inline u32 xgpio_get_value32(const unsigned long *map, int bit)
89 {
90 	const size_t index = BIT_WORD(bit);
91 	const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);
92 
93 	return (map[index] >> offset) & 0xFFFFFFFFul;
94 }
95 
96 static inline void xgpio_set_value32(unsigned long *map, int bit, u32 v)
97 {
98 	const size_t index = BIT_WORD(bit);
99 	const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);
100 
101 	map[index] &= ~(0xFFFFFFFFul << offset);
102 	map[index] |= (unsigned long)v << offset;
103 }
104 
105 static inline int xgpio_regoffset(struct xgpio_instance *chip, int ch)
106 {
107 	switch (ch) {
108 	case 0:
109 		return XGPIO_CHANNEL0_OFFSET;
110 	case 1:
111 		return XGPIO_CHANNEL1_OFFSET;
112 	default:
113 		return -EINVAL;
114 	}
115 }
116 
117 static void xgpio_read_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
118 {
119 	void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
120 
121 	xgpio_set_value32(a, bit, xgpio_readreg(addr));
122 }
123 
124 static void xgpio_write_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
125 {
126 	void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
127 
128 	xgpio_writereg(addr, xgpio_get_value32(a, bit));
129 }
130 
131 static void xgpio_read_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
132 {
133 	int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);
134 
135 	for (bit = 0; bit <= lastbit ; bit += 32)
136 		xgpio_read_ch(chip, reg, bit, a);
137 }
138 
139 static void xgpio_write_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
140 {
141 	int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);
142 
143 	for (bit = 0; bit <= lastbit ; bit += 32)
144 		xgpio_write_ch(chip, reg, bit, a);
145 }
146 
147 /**
148  * xgpio_get - Read the specified signal of the GPIO device.
149  * @gc:     Pointer to gpio_chip device structure.
150  * @gpio:   GPIO signal number.
151  *
152  * This function reads the specified signal of the GPIO device.
153  *
154  * Return:
155  * 0 if direction of GPIO signals is set as input otherwise it
156  * returns negative error value.
157  */
158 static int xgpio_get(struct gpio_chip *gc, unsigned int gpio)
159 {
160 	struct xgpio_instance *chip = gpiochip_get_data(gc);
161 	int bit = xgpio_to_bit(chip, gpio);
162 	DECLARE_BITMAP(state, 64);
163 
164 	xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, state);
165 
166 	return test_bit(bit, state);
167 }
168 
169 /**
170  * xgpio_set - Write the specified signal of the GPIO device.
171  * @gc:     Pointer to gpio_chip device structure.
172  * @gpio:   GPIO signal number.
173  * @val:    Value to be written to specified signal.
174  *
175  * This function writes the specified value in to the specified signal of the
176  * GPIO device.
177  */
178 static void xgpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
179 {
180 	unsigned long flags;
181 	struct xgpio_instance *chip = gpiochip_get_data(gc);
182 	int bit = xgpio_to_bit(chip, gpio);
183 
184 	spin_lock_irqsave(&chip->gpio_lock, flags);
185 
186 	/* Write to GPIO signal and set its direction to output */
187 	__assign_bit(bit, chip->state, val);
188 
189 	xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);
190 
191 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
192 }
193 
194 /**
195  * xgpio_set_multiple - Write the specified signals of the GPIO device.
196  * @gc:     Pointer to gpio_chip device structure.
197  * @mask:   Mask of the GPIOS to modify.
198  * @bits:   Value to be wrote on each GPIO
199  *
200  * This function writes the specified values into the specified signals of the
201  * GPIO devices.
202  */
203 static void xgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask,
204 			       unsigned long *bits)
205 {
206 	DECLARE_BITMAP(hw_mask, 64);
207 	DECLARE_BITMAP(hw_bits, 64);
208 	DECLARE_BITMAP(state, 64);
209 	unsigned long flags;
210 	struct xgpio_instance *chip = gpiochip_get_data(gc);
211 
212 	bitmap_remap(hw_mask, mask, chip->sw_map, chip->hw_map, 64);
213 	bitmap_remap(hw_bits, bits, chip->sw_map, chip->hw_map, 64);
214 
215 	spin_lock_irqsave(&chip->gpio_lock, flags);
216 
217 	bitmap_replace(state, chip->state, hw_bits, hw_mask, 64);
218 
219 	xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, state);
220 
221 	bitmap_copy(chip->state, state, 64);
222 
223 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
224 }
225 
226 /**
227  * xgpio_dir_in - Set the direction of the specified GPIO signal as input.
228  * @gc:     Pointer to gpio_chip device structure.
229  * @gpio:   GPIO signal number.
230  *
231  * Return:
232  * 0 - if direction of GPIO signals is set as input
233  * otherwise it returns negative error value.
234  */
235 static int xgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
236 {
237 	unsigned long flags;
238 	struct xgpio_instance *chip = gpiochip_get_data(gc);
239 	int bit = xgpio_to_bit(chip, gpio);
240 
241 	spin_lock_irqsave(&chip->gpio_lock, flags);
242 
243 	/* Set the GPIO bit in shadow register and set direction as input */
244 	__set_bit(bit, chip->dir);
245 	xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
246 
247 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
248 
249 	return 0;
250 }
251 
252 /**
253  * xgpio_dir_out - Set the direction of the specified GPIO signal as output.
254  * @gc:     Pointer to gpio_chip device structure.
255  * @gpio:   GPIO signal number.
256  * @val:    Value to be written to specified signal.
257  *
258  * This function sets the direction of specified GPIO signal as output.
259  *
260  * Return:
261  * If all GPIO signals of GPIO chip is configured as input then it returns
262  * error otherwise it returns 0.
263  */
264 static int xgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
265 {
266 	unsigned long flags;
267 	struct xgpio_instance *chip = gpiochip_get_data(gc);
268 	int bit = xgpio_to_bit(chip, gpio);
269 
270 	spin_lock_irqsave(&chip->gpio_lock, flags);
271 
272 	/* Write state of GPIO signal */
273 	__assign_bit(bit, chip->state, val);
274 	xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);
275 
276 	/* Clear the GPIO bit in shadow register and set direction as output */
277 	__clear_bit(bit, chip->dir);
278 	xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
279 
280 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
281 
282 	return 0;
283 }
284 
285 /**
286  * xgpio_save_regs - Set initial values of GPIO pins
287  * @chip: Pointer to GPIO instance
288  */
289 static void xgpio_save_regs(struct xgpio_instance *chip)
290 {
291 	xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, chip->state);
292 	xgpio_write_ch_all(chip, XGPIO_TRI_OFFSET, chip->dir);
293 }
294 
295 static int xgpio_request(struct gpio_chip *chip, unsigned int offset)
296 {
297 	int ret;
298 
299 	ret = pm_runtime_get_sync(chip->parent);
300 	/*
301 	 * If the device is already active pm_runtime_get() will return 1 on
302 	 * success, but gpio_request still needs to return 0.
303 	 */
304 	return ret < 0 ? ret : 0;
305 }
306 
307 static void xgpio_free(struct gpio_chip *chip, unsigned int offset)
308 {
309 	pm_runtime_put(chip->parent);
310 }
311 
312 static int __maybe_unused xgpio_suspend(struct device *dev)
313 {
314 	struct xgpio_instance *gpio = dev_get_drvdata(dev);
315 	struct irq_data *data = irq_get_irq_data(gpio->irq);
316 
317 	if (!data) {
318 		dev_dbg(dev, "IRQ not connected\n");
319 		return pm_runtime_force_suspend(dev);
320 	}
321 
322 	if (!irqd_is_wakeup_set(data))
323 		return pm_runtime_force_suspend(dev);
324 
325 	return 0;
326 }
327 
328 /**
329  * xgpio_remove - Remove method for the GPIO device.
330  * @pdev: pointer to the platform device
331  *
332  * This function remove gpiochips and frees all the allocated resources.
333  *
334  * Return: 0 always
335  */
336 static int xgpio_remove(struct platform_device *pdev)
337 {
338 	struct xgpio_instance *gpio = platform_get_drvdata(pdev);
339 
340 	pm_runtime_get_sync(&pdev->dev);
341 	pm_runtime_put_noidle(&pdev->dev);
342 	pm_runtime_disable(&pdev->dev);
343 	clk_disable_unprepare(gpio->clk);
344 
345 	return 0;
346 }
347 
348 /**
349  * xgpio_irq_ack - Acknowledge a child GPIO interrupt.
350  * @irq_data: per IRQ and chip data passed down to chip functions
351  * This currently does nothing, but irq_ack is unconditionally called by
352  * handle_edge_irq and therefore must be defined.
353  */
354 static void xgpio_irq_ack(struct irq_data *irq_data)
355 {
356 }
357 
358 static int __maybe_unused xgpio_resume(struct device *dev)
359 {
360 	struct xgpio_instance *gpio = dev_get_drvdata(dev);
361 	struct irq_data *data = irq_get_irq_data(gpio->irq);
362 
363 	if (!data) {
364 		dev_dbg(dev, "IRQ not connected\n");
365 		return pm_runtime_force_resume(dev);
366 	}
367 
368 	if (!irqd_is_wakeup_set(data))
369 		return pm_runtime_force_resume(dev);
370 
371 	return 0;
372 }
373 
374 static int __maybe_unused xgpio_runtime_suspend(struct device *dev)
375 {
376 	struct xgpio_instance *gpio = dev_get_drvdata(dev);
377 
378 	clk_disable(gpio->clk);
379 
380 	return 0;
381 }
382 
383 static int __maybe_unused xgpio_runtime_resume(struct device *dev)
384 {
385 	struct xgpio_instance *gpio = dev_get_drvdata(dev);
386 
387 	return clk_enable(gpio->clk);
388 }
389 
390 static const struct dev_pm_ops xgpio_dev_pm_ops = {
391 	SET_SYSTEM_SLEEP_PM_OPS(xgpio_suspend, xgpio_resume)
392 	SET_RUNTIME_PM_OPS(xgpio_runtime_suspend,
393 			   xgpio_runtime_resume, NULL)
394 };
395 
396 /**
397  * xgpio_irq_mask - Write the specified signal of the GPIO device.
398  * @irq_data: per IRQ and chip data passed down to chip functions
399  */
400 static void xgpio_irq_mask(struct irq_data *irq_data)
401 {
402 	unsigned long flags;
403 	struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
404 	int irq_offset = irqd_to_hwirq(irq_data);
405 	int bit = xgpio_to_bit(chip, irq_offset);
406 	u32 mask = BIT(bit / 32), temp;
407 
408 	spin_lock_irqsave(&chip->gpio_lock, flags);
409 
410 	__clear_bit(bit, chip->enable);
411 
412 	if (xgpio_get_value32(chip->enable, bit) == 0) {
413 		/* Disable per channel interrupt */
414 		temp = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
415 		temp &= ~mask;
416 		xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, temp);
417 	}
418 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
419 }
420 
421 /**
422  * xgpio_irq_unmask - Write the specified signal of the GPIO device.
423  * @irq_data: per IRQ and chip data passed down to chip functions
424  */
425 static void xgpio_irq_unmask(struct irq_data *irq_data)
426 {
427 	unsigned long flags;
428 	struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
429 	int irq_offset = irqd_to_hwirq(irq_data);
430 	int bit = xgpio_to_bit(chip, irq_offset);
431 	u32 old_enable = xgpio_get_value32(chip->enable, bit);
432 	u32 mask = BIT(bit / 32), val;
433 
434 	spin_lock_irqsave(&chip->gpio_lock, flags);
435 
436 	__set_bit(bit, chip->enable);
437 
438 	if (old_enable == 0) {
439 		/* Clear any existing per-channel interrupts */
440 		val = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
441 		val &= mask;
442 		xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, val);
443 
444 		/* Update GPIO IRQ read data before enabling interrupt*/
445 		xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, chip->last_irq_read);
446 
447 		/* Enable per channel interrupt */
448 		val = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
449 		val |= mask;
450 		xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, val);
451 	}
452 
453 	spin_unlock_irqrestore(&chip->gpio_lock, flags);
454 }
455 
456 /**
457  * xgpio_set_irq_type - Write the specified signal of the GPIO device.
458  * @irq_data: Per IRQ and chip data passed down to chip functions
459  * @type: Interrupt type that is to be set for the gpio pin
460  *
461  * Return:
462  * 0 if interrupt type is supported otherwise -EINVAL
463  */
464 static int xgpio_set_irq_type(struct irq_data *irq_data, unsigned int type)
465 {
466 	struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
467 	int irq_offset = irqd_to_hwirq(irq_data);
468 	int bit = xgpio_to_bit(chip, irq_offset);
469 
470 	/*
471 	 * The Xilinx GPIO hardware provides a single interrupt status
472 	 * indication for any state change in a given GPIO channel (bank).
473 	 * Therefore, only rising edge or falling edge triggers are
474 	 * supported.
475 	 */
476 	switch (type & IRQ_TYPE_SENSE_MASK) {
477 	case IRQ_TYPE_EDGE_BOTH:
478 		__set_bit(bit, chip->rising_edge);
479 		__set_bit(bit, chip->falling_edge);
480 		break;
481 	case IRQ_TYPE_EDGE_RISING:
482 		__set_bit(bit, chip->rising_edge);
483 		__clear_bit(bit, chip->falling_edge);
484 		break;
485 	case IRQ_TYPE_EDGE_FALLING:
486 		__clear_bit(bit, chip->rising_edge);
487 		__set_bit(bit, chip->falling_edge);
488 		break;
489 	default:
490 		return -EINVAL;
491 	}
492 
493 	irq_set_handler_locked(irq_data, handle_edge_irq);
494 	return 0;
495 }
496 
497 /**
498  * xgpio_irqhandler - Gpio interrupt service routine
499  * @desc: Pointer to interrupt description
500  */
501 static void xgpio_irqhandler(struct irq_desc *desc)
502 {
503 	struct xgpio_instance *chip = irq_desc_get_handler_data(desc);
504 	struct gpio_chip *gc = &chip->gc;
505 	struct irq_chip *irqchip = irq_desc_get_chip(desc);
506 	DECLARE_BITMAP(rising, 64);
507 	DECLARE_BITMAP(falling, 64);
508 	DECLARE_BITMAP(all, 64);
509 	int irq_offset;
510 	u32 status;
511 	u32 bit;
512 
513 	status = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
514 	xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, status);
515 
516 	chained_irq_enter(irqchip, desc);
517 
518 	spin_lock(&chip->gpio_lock);
519 
520 	xgpio_read_ch_all(chip, XGPIO_DATA_OFFSET, all);
521 
522 	bitmap_complement(rising, chip->last_irq_read, 64);
523 	bitmap_and(rising, rising, all, 64);
524 	bitmap_and(rising, rising, chip->enable, 64);
525 	bitmap_and(rising, rising, chip->rising_edge, 64);
526 
527 	bitmap_complement(falling, all, 64);
528 	bitmap_and(falling, falling, chip->last_irq_read, 64);
529 	bitmap_and(falling, falling, chip->enable, 64);
530 	bitmap_and(falling, falling, chip->falling_edge, 64);
531 
532 	bitmap_copy(chip->last_irq_read, all, 64);
533 	bitmap_or(all, rising, falling, 64);
534 
535 	spin_unlock(&chip->gpio_lock);
536 
537 	dev_dbg(gc->parent, "IRQ rising %*pb falling %*pb\n", 64, rising, 64, falling);
538 
539 	for_each_set_bit(bit, all, 64) {
540 		irq_offset = xgpio_from_bit(chip, bit);
541 		generic_handle_domain_irq(gc->irq.domain, irq_offset);
542 	}
543 
544 	chained_irq_exit(irqchip, desc);
545 }
546 
547 /**
548  * xgpio_probe - Probe method for the GPIO device.
549  * @pdev: pointer to the platform device
550  *
551  * Return:
552  * It returns 0, if the driver is bound to the GPIO device, or
553  * a negative value if there is an error.
554  */
555 static int xgpio_probe(struct platform_device *pdev)
556 {
557 	struct xgpio_instance *chip;
558 	int status = 0;
559 	struct device_node *np = pdev->dev.of_node;
560 	u32 is_dual = 0;
561 	u32 width[2];
562 	u32 state[2];
563 	u32 dir[2];
564 	struct gpio_irq_chip *girq;
565 	u32 temp;
566 
567 	chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
568 	if (!chip)
569 		return -ENOMEM;
570 
571 	platform_set_drvdata(pdev, chip);
572 
573 	/* First, check if the device is dual-channel */
574 	of_property_read_u32(np, "xlnx,is-dual", &is_dual);
575 
576 	/* Setup defaults */
577 	memset32(width, 0, ARRAY_SIZE(width));
578 	memset32(state, 0, ARRAY_SIZE(state));
579 	memset32(dir, 0xFFFFFFFF, ARRAY_SIZE(dir));
580 
581 	/* Update GPIO state shadow register with default value */
582 	of_property_read_u32(np, "xlnx,dout-default", &state[0]);
583 	of_property_read_u32(np, "xlnx,dout-default-2", &state[1]);
584 
585 	bitmap_from_arr32(chip->state, state, 64);
586 
587 	/* Update GPIO direction shadow register with default value */
588 	of_property_read_u32(np, "xlnx,tri-default", &dir[0]);
589 	of_property_read_u32(np, "xlnx,tri-default-2", &dir[1]);
590 
591 	bitmap_from_arr32(chip->dir, dir, 64);
592 
593 	/*
594 	 * Check device node and parent device node for device width
595 	 * and assume default width of 32
596 	 */
597 	if (of_property_read_u32(np, "xlnx,gpio-width", &width[0]))
598 		width[0] = 32;
599 
600 	if (width[0] > 32)
601 		return -EINVAL;
602 
603 	if (is_dual && of_property_read_u32(np, "xlnx,gpio2-width", &width[1]))
604 		width[1] = 32;
605 
606 	if (width[1] > 32)
607 		return -EINVAL;
608 
609 	/* Setup software pin mapping */
610 	bitmap_set(chip->sw_map, 0, width[0] + width[1]);
611 
612 	/* Setup hardware pin mapping */
613 	bitmap_set(chip->hw_map,  0, width[0]);
614 	bitmap_set(chip->hw_map, 32, width[1]);
615 
616 	spin_lock_init(&chip->gpio_lock);
617 
618 	chip->gc.base = -1;
619 	chip->gc.ngpio = bitmap_weight(chip->hw_map, 64);
620 	chip->gc.parent = &pdev->dev;
621 	chip->gc.direction_input = xgpio_dir_in;
622 	chip->gc.direction_output = xgpio_dir_out;
623 	chip->gc.get = xgpio_get;
624 	chip->gc.set = xgpio_set;
625 	chip->gc.request = xgpio_request;
626 	chip->gc.free = xgpio_free;
627 	chip->gc.set_multiple = xgpio_set_multiple;
628 
629 	chip->gc.label = dev_name(&pdev->dev);
630 
631 	chip->regs = devm_platform_ioremap_resource(pdev, 0);
632 	if (IS_ERR(chip->regs)) {
633 		dev_err(&pdev->dev, "failed to ioremap memory resource\n");
634 		return PTR_ERR(chip->regs);
635 	}
636 
637 	chip->clk = devm_clk_get_optional(&pdev->dev, NULL);
638 	if (IS_ERR(chip->clk))
639 		return dev_err_probe(&pdev->dev, PTR_ERR(chip->clk), "input clock not found.\n");
640 
641 	status = clk_prepare_enable(chip->clk);
642 	if (status < 0) {
643 		dev_err(&pdev->dev, "Failed to prepare clk\n");
644 		return status;
645 	}
646 	pm_runtime_get_noresume(&pdev->dev);
647 	pm_runtime_set_active(&pdev->dev);
648 	pm_runtime_enable(&pdev->dev);
649 
650 	xgpio_save_regs(chip);
651 
652 	chip->irq = platform_get_irq_optional(pdev, 0);
653 	if (chip->irq <= 0)
654 		goto skip_irq;
655 
656 	chip->irqchip.name = "gpio-xilinx";
657 	chip->irqchip.irq_ack = xgpio_irq_ack;
658 	chip->irqchip.irq_mask = xgpio_irq_mask;
659 	chip->irqchip.irq_unmask = xgpio_irq_unmask;
660 	chip->irqchip.irq_set_type = xgpio_set_irq_type;
661 
662 	/* Disable per-channel interrupts */
663 	xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, 0);
664 	/* Clear any existing per-channel interrupts */
665 	temp = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
666 	xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, temp);
667 	/* Enable global interrupts */
668 	xgpio_writereg(chip->regs + XGPIO_GIER_OFFSET, XGPIO_GIER_IE);
669 
670 	girq = &chip->gc.irq;
671 	girq->chip = &chip->irqchip;
672 	girq->parent_handler = xgpio_irqhandler;
673 	girq->num_parents = 1;
674 	girq->parents = devm_kcalloc(&pdev->dev, 1,
675 				     sizeof(*girq->parents),
676 				     GFP_KERNEL);
677 	if (!girq->parents) {
678 		status = -ENOMEM;
679 		goto err_pm_put;
680 	}
681 	girq->parents[0] = chip->irq;
682 	girq->default_type = IRQ_TYPE_NONE;
683 	girq->handler = handle_bad_irq;
684 
685 skip_irq:
686 	status = devm_gpiochip_add_data(&pdev->dev, &chip->gc, chip);
687 	if (status) {
688 		dev_err(&pdev->dev, "failed to add GPIO chip\n");
689 		goto err_pm_put;
690 	}
691 
692 	pm_runtime_put(&pdev->dev);
693 	return 0;
694 
695 err_pm_put:
696 	pm_runtime_disable(&pdev->dev);
697 	pm_runtime_put_noidle(&pdev->dev);
698 	clk_disable_unprepare(chip->clk);
699 	return status;
700 }
701 
702 static const struct of_device_id xgpio_of_match[] = {
703 	{ .compatible = "xlnx,xps-gpio-1.00.a", },
704 	{ /* end of list */ },
705 };
706 
707 MODULE_DEVICE_TABLE(of, xgpio_of_match);
708 
709 static struct platform_driver xgpio_plat_driver = {
710 	.probe		= xgpio_probe,
711 	.remove		= xgpio_remove,
712 	.driver		= {
713 			.name = "gpio-xilinx",
714 			.of_match_table	= xgpio_of_match,
715 			.pm = &xgpio_dev_pm_ops,
716 	},
717 };
718 
719 static int __init xgpio_init(void)
720 {
721 	return platform_driver_register(&xgpio_plat_driver);
722 }
723 
724 subsys_initcall(xgpio_init);
725 
726 static void __exit xgpio_exit(void)
727 {
728 	platform_driver_unregister(&xgpio_plat_driver);
729 }
730 module_exit(xgpio_exit);
731 
732 MODULE_AUTHOR("Xilinx, Inc.");
733 MODULE_DESCRIPTION("Xilinx GPIO driver");
734 MODULE_LICENSE("GPL");
735