1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Xilinx gpio driver for xps/axi_gpio IP.
4 *
5 * Copyright 2008 - 2013 Xilinx, Inc.
6 */
7
8 #include <linux/bitmap.h>
9 #include <linux/bitops.h>
10 #include <linux/clk.h>
11 #include <linux/errno.h>
12 #include <linux/gpio/driver.h>
13 #include <linux/init.h>
14 #include <linux/interrupt.h>
15 #include <linux/io.h>
16 #include <linux/irq.h>
17 #include <linux/module.h>
18 #include <linux/of.h>
19 #include <linux/platform_device.h>
20 #include <linux/pm_runtime.h>
21 #include <linux/slab.h>
22
23 /* Register Offset Definitions */
24 #define XGPIO_DATA_OFFSET (0x0) /* Data register */
25 #define XGPIO_TRI_OFFSET (0x4) /* I/O direction register */
26
27 #define XGPIO_CHANNEL0_OFFSET 0x0
28 #define XGPIO_CHANNEL1_OFFSET 0x8
29
30 #define XGPIO_GIER_OFFSET 0x11c /* Global Interrupt Enable */
31 #define XGPIO_GIER_IE BIT(31)
32 #define XGPIO_IPISR_OFFSET 0x120 /* IP Interrupt Status */
33 #define XGPIO_IPIER_OFFSET 0x128 /* IP Interrupt Enable */
34
35 /* Read/Write access to the GPIO registers */
36 #if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_X86)
37 # define xgpio_readreg(offset) readl(offset)
38 # define xgpio_writereg(offset, val) writel(val, offset)
39 #else
40 # define xgpio_readreg(offset) __raw_readl(offset)
41 # define xgpio_writereg(offset, val) __raw_writel(val, offset)
42 #endif
43
44 /**
45 * struct xgpio_instance - Stores information about GPIO device
46 * @gc: GPIO chip
47 * @regs: register block
48 * @hw_map: GPIO pin mapping on hardware side
49 * @sw_map: GPIO pin mapping on software side
50 * @state: GPIO write state shadow register
51 * @last_irq_read: GPIO read state register from last interrupt
52 * @dir: GPIO direction shadow register
53 * @gpio_lock: Lock used for synchronization
54 * @irq: IRQ used by GPIO device
55 * @irqchip: IRQ chip
56 * @enable: GPIO IRQ enable/disable bitfield
57 * @rising_edge: GPIO IRQ rising edge enable/disable bitfield
58 * @falling_edge: GPIO IRQ falling edge enable/disable bitfield
59 * @clk: clock resource for this driver
60 */
61 struct xgpio_instance {
62 struct gpio_chip gc;
63 void __iomem *regs;
64 DECLARE_BITMAP(hw_map, 64);
65 DECLARE_BITMAP(sw_map, 64);
66 DECLARE_BITMAP(state, 64);
67 DECLARE_BITMAP(last_irq_read, 64);
68 DECLARE_BITMAP(dir, 64);
69 spinlock_t gpio_lock; /* For serializing operations */
70 int irq;
71 DECLARE_BITMAP(enable, 64);
72 DECLARE_BITMAP(rising_edge, 64);
73 DECLARE_BITMAP(falling_edge, 64);
74 struct clk *clk;
75 };
76
xgpio_from_bit(struct xgpio_instance * chip,int bit)77 static inline int xgpio_from_bit(struct xgpio_instance *chip, int bit)
78 {
79 return bitmap_bitremap(bit, chip->hw_map, chip->sw_map, 64);
80 }
81
xgpio_to_bit(struct xgpio_instance * chip,int gpio)82 static inline int xgpio_to_bit(struct xgpio_instance *chip, int gpio)
83 {
84 return bitmap_bitremap(gpio, chip->sw_map, chip->hw_map, 64);
85 }
86
xgpio_get_value32(const unsigned long * map,int bit)87 static inline u32 xgpio_get_value32(const unsigned long *map, int bit)
88 {
89 const size_t index = BIT_WORD(bit);
90 const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);
91
92 return (map[index] >> offset) & 0xFFFFFFFFul;
93 }
94
xgpio_set_value32(unsigned long * map,int bit,u32 v)95 static inline void xgpio_set_value32(unsigned long *map, int bit, u32 v)
96 {
97 const size_t index = BIT_WORD(bit);
98 const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);
99
100 map[index] &= ~(0xFFFFFFFFul << offset);
101 map[index] |= (unsigned long)v << offset;
102 }
103
xgpio_regoffset(struct xgpio_instance * chip,int ch)104 static inline int xgpio_regoffset(struct xgpio_instance *chip, int ch)
105 {
106 switch (ch) {
107 case 0:
108 return XGPIO_CHANNEL0_OFFSET;
109 case 1:
110 return XGPIO_CHANNEL1_OFFSET;
111 default:
112 return -EINVAL;
113 }
114 }
115
xgpio_read_ch(struct xgpio_instance * chip,int reg,int bit,unsigned long * a)116 static void xgpio_read_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
117 {
118 void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
119
120 xgpio_set_value32(a, bit, xgpio_readreg(addr));
121 }
122
xgpio_write_ch(struct xgpio_instance * chip,int reg,int bit,unsigned long * a)123 static void xgpio_write_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
124 {
125 void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);
126
127 xgpio_writereg(addr, xgpio_get_value32(a, bit));
128 }
129
xgpio_read_ch_all(struct xgpio_instance * chip,int reg,unsigned long * a)130 static void xgpio_read_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
131 {
132 int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);
133
134 for (bit = 0; bit <= lastbit ; bit += 32)
135 xgpio_read_ch(chip, reg, bit, a);
136 }
137
xgpio_write_ch_all(struct xgpio_instance * chip,int reg,unsigned long * a)138 static void xgpio_write_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
139 {
140 int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);
141
142 for (bit = 0; bit <= lastbit ; bit += 32)
143 xgpio_write_ch(chip, reg, bit, a);
144 }
145
146 /**
147 * xgpio_get - Read the specified signal of the GPIO device.
148 * @gc: Pointer to gpio_chip device structure.
149 * @gpio: GPIO signal number.
150 *
151 * This function reads the specified signal of the GPIO device.
152 *
153 * Return:
154 * 0 if direction of GPIO signals is set as input otherwise it
155 * returns negative error value.
156 */
xgpio_get(struct gpio_chip * gc,unsigned int gpio)157 static int xgpio_get(struct gpio_chip *gc, unsigned int gpio)
158 {
159 struct xgpio_instance *chip = gpiochip_get_data(gc);
160 int bit = xgpio_to_bit(chip, gpio);
161 DECLARE_BITMAP(state, 64);
162
163 xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, state);
164
165 return test_bit(bit, state);
166 }
167
168 /**
169 * xgpio_set - Write the specified signal of the GPIO device.
170 * @gc: Pointer to gpio_chip device structure.
171 * @gpio: GPIO signal number.
172 * @val: Value to be written to specified signal.
173 *
174 * This function writes the specified value in to the specified signal of the
175 * GPIO device.
176 */
xgpio_set(struct gpio_chip * gc,unsigned int gpio,int val)177 static void xgpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
178 {
179 unsigned long flags;
180 struct xgpio_instance *chip = gpiochip_get_data(gc);
181 int bit = xgpio_to_bit(chip, gpio);
182
183 spin_lock_irqsave(&chip->gpio_lock, flags);
184
185 /* Write to GPIO signal and set its direction to output */
186 __assign_bit(bit, chip->state, val);
187
188 xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);
189
190 spin_unlock_irqrestore(&chip->gpio_lock, flags);
191 }
192
193 /**
194 * xgpio_set_multiple - Write the specified signals of the GPIO device.
195 * @gc: Pointer to gpio_chip device structure.
196 * @mask: Mask of the GPIOS to modify.
197 * @bits: Value to be wrote on each GPIO
198 *
199 * This function writes the specified values into the specified signals of the
200 * GPIO devices.
201 */
xgpio_set_multiple(struct gpio_chip * gc,unsigned long * mask,unsigned long * bits)202 static void xgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask,
203 unsigned long *bits)
204 {
205 DECLARE_BITMAP(hw_mask, 64);
206 DECLARE_BITMAP(hw_bits, 64);
207 DECLARE_BITMAP(state, 64);
208 unsigned long flags;
209 struct xgpio_instance *chip = gpiochip_get_data(gc);
210
211 bitmap_remap(hw_mask, mask, chip->sw_map, chip->hw_map, 64);
212 bitmap_remap(hw_bits, bits, chip->sw_map, chip->hw_map, 64);
213
214 spin_lock_irqsave(&chip->gpio_lock, flags);
215
216 bitmap_replace(state, chip->state, hw_bits, hw_mask, 64);
217
218 xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, state);
219
220 bitmap_copy(chip->state, state, 64);
221
222 spin_unlock_irqrestore(&chip->gpio_lock, flags);
223 }
224
225 /**
226 * xgpio_dir_in - Set the direction of the specified GPIO signal as input.
227 * @gc: Pointer to gpio_chip device structure.
228 * @gpio: GPIO signal number.
229 *
230 * Return:
231 * 0 - if direction of GPIO signals is set as input
232 * otherwise it returns negative error value.
233 */
xgpio_dir_in(struct gpio_chip * gc,unsigned int gpio)234 static int xgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
235 {
236 unsigned long flags;
237 struct xgpio_instance *chip = gpiochip_get_data(gc);
238 int bit = xgpio_to_bit(chip, gpio);
239
240 spin_lock_irqsave(&chip->gpio_lock, flags);
241
242 /* Set the GPIO bit in shadow register and set direction as input */
243 __set_bit(bit, chip->dir);
244 xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
245
246 spin_unlock_irqrestore(&chip->gpio_lock, flags);
247
248 return 0;
249 }
250
251 /**
252 * xgpio_dir_out - Set the direction of the specified GPIO signal as output.
253 * @gc: Pointer to gpio_chip device structure.
254 * @gpio: GPIO signal number.
255 * @val: Value to be written to specified signal.
256 *
257 * This function sets the direction of specified GPIO signal as output.
258 *
259 * Return:
260 * If all GPIO signals of GPIO chip is configured as input then it returns
261 * error otherwise it returns 0.
262 */
xgpio_dir_out(struct gpio_chip * gc,unsigned int gpio,int val)263 static int xgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
264 {
265 unsigned long flags;
266 struct xgpio_instance *chip = gpiochip_get_data(gc);
267 int bit = xgpio_to_bit(chip, gpio);
268
269 spin_lock_irqsave(&chip->gpio_lock, flags);
270
271 /* Write state of GPIO signal */
272 __assign_bit(bit, chip->state, val);
273 xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);
274
275 /* Clear the GPIO bit in shadow register and set direction as output */
276 __clear_bit(bit, chip->dir);
277 xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);
278
279 spin_unlock_irqrestore(&chip->gpio_lock, flags);
280
281 return 0;
282 }
283
284 /**
285 * xgpio_save_regs - Set initial values of GPIO pins
286 * @chip: Pointer to GPIO instance
287 */
xgpio_save_regs(struct xgpio_instance * chip)288 static void xgpio_save_regs(struct xgpio_instance *chip)
289 {
290 xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, chip->state);
291 xgpio_write_ch_all(chip, XGPIO_TRI_OFFSET, chip->dir);
292 }
293
xgpio_request(struct gpio_chip * chip,unsigned int offset)294 static int xgpio_request(struct gpio_chip *chip, unsigned int offset)
295 {
296 int ret;
297
298 ret = pm_runtime_get_sync(chip->parent);
299 /*
300 * If the device is already active pm_runtime_get() will return 1 on
301 * success, but gpio_request still needs to return 0.
302 */
303 return ret < 0 ? ret : 0;
304 }
305
xgpio_free(struct gpio_chip * chip,unsigned int offset)306 static void xgpio_free(struct gpio_chip *chip, unsigned int offset)
307 {
308 pm_runtime_put(chip->parent);
309 }
310
xgpio_suspend(struct device * dev)311 static int __maybe_unused xgpio_suspend(struct device *dev)
312 {
313 struct xgpio_instance *gpio = dev_get_drvdata(dev);
314 struct irq_data *data = irq_get_irq_data(gpio->irq);
315
316 if (!data) {
317 dev_dbg(dev, "IRQ not connected\n");
318 return pm_runtime_force_suspend(dev);
319 }
320
321 if (!irqd_is_wakeup_set(data))
322 return pm_runtime_force_suspend(dev);
323
324 return 0;
325 }
326
327 /**
328 * xgpio_remove - Remove method for the GPIO device.
329 * @pdev: pointer to the platform device
330 *
331 * This function remove gpiochips and frees all the allocated resources.
332 *
333 * Return: 0 always
334 */
xgpio_remove(struct platform_device * pdev)335 static int xgpio_remove(struct platform_device *pdev)
336 {
337 struct xgpio_instance *gpio = platform_get_drvdata(pdev);
338
339 pm_runtime_get_sync(&pdev->dev);
340 pm_runtime_put_noidle(&pdev->dev);
341 pm_runtime_disable(&pdev->dev);
342 clk_disable_unprepare(gpio->clk);
343
344 return 0;
345 }
346
347 /**
348 * xgpio_irq_ack - Acknowledge a child GPIO interrupt.
349 * @irq_data: per IRQ and chip data passed down to chip functions
350 * This currently does nothing, but irq_ack is unconditionally called by
351 * handle_edge_irq and therefore must be defined.
352 */
xgpio_irq_ack(struct irq_data * irq_data)353 static void xgpio_irq_ack(struct irq_data *irq_data)
354 {
355 }
356
xgpio_resume(struct device * dev)357 static int __maybe_unused xgpio_resume(struct device *dev)
358 {
359 struct xgpio_instance *gpio = dev_get_drvdata(dev);
360 struct irq_data *data = irq_get_irq_data(gpio->irq);
361
362 if (!data) {
363 dev_dbg(dev, "IRQ not connected\n");
364 return pm_runtime_force_resume(dev);
365 }
366
367 if (!irqd_is_wakeup_set(data))
368 return pm_runtime_force_resume(dev);
369
370 return 0;
371 }
372
xgpio_runtime_suspend(struct device * dev)373 static int __maybe_unused xgpio_runtime_suspend(struct device *dev)
374 {
375 struct xgpio_instance *gpio = dev_get_drvdata(dev);
376
377 clk_disable(gpio->clk);
378
379 return 0;
380 }
381
xgpio_runtime_resume(struct device * dev)382 static int __maybe_unused xgpio_runtime_resume(struct device *dev)
383 {
384 struct xgpio_instance *gpio = dev_get_drvdata(dev);
385
386 return clk_enable(gpio->clk);
387 }
388
389 static const struct dev_pm_ops xgpio_dev_pm_ops = {
390 SET_SYSTEM_SLEEP_PM_OPS(xgpio_suspend, xgpio_resume)
391 SET_RUNTIME_PM_OPS(xgpio_runtime_suspend,
392 xgpio_runtime_resume, NULL)
393 };
394
395 /**
396 * xgpio_irq_mask - Write the specified signal of the GPIO device.
397 * @irq_data: per IRQ and chip data passed down to chip functions
398 */
xgpio_irq_mask(struct irq_data * irq_data)399 static void xgpio_irq_mask(struct irq_data *irq_data)
400 {
401 unsigned long flags;
402 struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
403 int irq_offset = irqd_to_hwirq(irq_data);
404 int bit = xgpio_to_bit(chip, irq_offset);
405 u32 mask = BIT(bit / 32), temp;
406
407 spin_lock_irqsave(&chip->gpio_lock, flags);
408
409 __clear_bit(bit, chip->enable);
410
411 if (xgpio_get_value32(chip->enable, bit) == 0) {
412 /* Disable per channel interrupt */
413 temp = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
414 temp &= ~mask;
415 xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, temp);
416 }
417 spin_unlock_irqrestore(&chip->gpio_lock, flags);
418
419 gpiochip_disable_irq(&chip->gc, irq_offset);
420 }
421
422 /**
423 * xgpio_irq_unmask - Write the specified signal of the GPIO device.
424 * @irq_data: per IRQ and chip data passed down to chip functions
425 */
xgpio_irq_unmask(struct irq_data * irq_data)426 static void xgpio_irq_unmask(struct irq_data *irq_data)
427 {
428 unsigned long flags;
429 struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
430 int irq_offset = irqd_to_hwirq(irq_data);
431 int bit = xgpio_to_bit(chip, irq_offset);
432 u32 old_enable = xgpio_get_value32(chip->enable, bit);
433 u32 mask = BIT(bit / 32), val;
434
435 gpiochip_enable_irq(&chip->gc, irq_offset);
436
437 spin_lock_irqsave(&chip->gpio_lock, flags);
438
439 __set_bit(bit, chip->enable);
440
441 if (old_enable == 0) {
442 /* Clear any existing per-channel interrupts */
443 val = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
444 val &= mask;
445 xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, val);
446
447 /* Update GPIO IRQ read data before enabling interrupt*/
448 xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, chip->last_irq_read);
449
450 /* Enable per channel interrupt */
451 val = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
452 val |= mask;
453 xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, val);
454 }
455
456 spin_unlock_irqrestore(&chip->gpio_lock, flags);
457 }
458
459 /**
460 * xgpio_set_irq_type - Write the specified signal of the GPIO device.
461 * @irq_data: Per IRQ and chip data passed down to chip functions
462 * @type: Interrupt type that is to be set for the gpio pin
463 *
464 * Return:
465 * 0 if interrupt type is supported otherwise -EINVAL
466 */
xgpio_set_irq_type(struct irq_data * irq_data,unsigned int type)467 static int xgpio_set_irq_type(struct irq_data *irq_data, unsigned int type)
468 {
469 struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
470 int irq_offset = irqd_to_hwirq(irq_data);
471 int bit = xgpio_to_bit(chip, irq_offset);
472
473 /*
474 * The Xilinx GPIO hardware provides a single interrupt status
475 * indication for any state change in a given GPIO channel (bank).
476 * Therefore, only rising edge or falling edge triggers are
477 * supported.
478 */
479 switch (type & IRQ_TYPE_SENSE_MASK) {
480 case IRQ_TYPE_EDGE_BOTH:
481 __set_bit(bit, chip->rising_edge);
482 __set_bit(bit, chip->falling_edge);
483 break;
484 case IRQ_TYPE_EDGE_RISING:
485 __set_bit(bit, chip->rising_edge);
486 __clear_bit(bit, chip->falling_edge);
487 break;
488 case IRQ_TYPE_EDGE_FALLING:
489 __clear_bit(bit, chip->rising_edge);
490 __set_bit(bit, chip->falling_edge);
491 break;
492 default:
493 return -EINVAL;
494 }
495
496 irq_set_handler_locked(irq_data, handle_edge_irq);
497 return 0;
498 }
499
500 /**
501 * xgpio_irqhandler - Gpio interrupt service routine
502 * @desc: Pointer to interrupt description
503 */
xgpio_irqhandler(struct irq_desc * desc)504 static void xgpio_irqhandler(struct irq_desc *desc)
505 {
506 struct xgpio_instance *chip = irq_desc_get_handler_data(desc);
507 struct gpio_chip *gc = &chip->gc;
508 struct irq_chip *irqchip = irq_desc_get_chip(desc);
509 DECLARE_BITMAP(rising, 64);
510 DECLARE_BITMAP(falling, 64);
511 DECLARE_BITMAP(all, 64);
512 int irq_offset;
513 u32 status;
514 u32 bit;
515
516 status = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
517 xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, status);
518
519 chained_irq_enter(irqchip, desc);
520
521 spin_lock(&chip->gpio_lock);
522
523 xgpio_read_ch_all(chip, XGPIO_DATA_OFFSET, all);
524
525 bitmap_complement(rising, chip->last_irq_read, 64);
526 bitmap_and(rising, rising, all, 64);
527 bitmap_and(rising, rising, chip->enable, 64);
528 bitmap_and(rising, rising, chip->rising_edge, 64);
529
530 bitmap_complement(falling, all, 64);
531 bitmap_and(falling, falling, chip->last_irq_read, 64);
532 bitmap_and(falling, falling, chip->enable, 64);
533 bitmap_and(falling, falling, chip->falling_edge, 64);
534
535 bitmap_copy(chip->last_irq_read, all, 64);
536 bitmap_or(all, rising, falling, 64);
537
538 spin_unlock(&chip->gpio_lock);
539
540 dev_dbg(gc->parent, "IRQ rising %*pb falling %*pb\n", 64, rising, 64, falling);
541
542 for_each_set_bit(bit, all, 64) {
543 irq_offset = xgpio_from_bit(chip, bit);
544 generic_handle_domain_irq(gc->irq.domain, irq_offset);
545 }
546
547 chained_irq_exit(irqchip, desc);
548 }
549
550 static const struct irq_chip xgpio_irq_chip = {
551 .name = "gpio-xilinx",
552 .irq_ack = xgpio_irq_ack,
553 .irq_mask = xgpio_irq_mask,
554 .irq_unmask = xgpio_irq_unmask,
555 .irq_set_type = xgpio_set_irq_type,
556 .flags = IRQCHIP_IMMUTABLE,
557 GPIOCHIP_IRQ_RESOURCE_HELPERS,
558 };
559
560 /**
561 * xgpio_probe - Probe method for the GPIO device.
562 * @pdev: pointer to the platform device
563 *
564 * Return:
565 * It returns 0, if the driver is bound to the GPIO device, or
566 * a negative value if there is an error.
567 */
xgpio_probe(struct platform_device * pdev)568 static int xgpio_probe(struct platform_device *pdev)
569 {
570 struct xgpio_instance *chip;
571 int status = 0;
572 struct device_node *np = pdev->dev.of_node;
573 u32 is_dual = 0;
574 u32 width[2];
575 u32 state[2];
576 u32 dir[2];
577 struct gpio_irq_chip *girq;
578 u32 temp;
579
580 chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
581 if (!chip)
582 return -ENOMEM;
583
584 platform_set_drvdata(pdev, chip);
585
586 /* First, check if the device is dual-channel */
587 of_property_read_u32(np, "xlnx,is-dual", &is_dual);
588
589 /* Setup defaults */
590 memset32(width, 0, ARRAY_SIZE(width));
591 memset32(state, 0, ARRAY_SIZE(state));
592 memset32(dir, 0xFFFFFFFF, ARRAY_SIZE(dir));
593
594 /* Update GPIO state shadow register with default value */
595 of_property_read_u32(np, "xlnx,dout-default", &state[0]);
596 of_property_read_u32(np, "xlnx,dout-default-2", &state[1]);
597
598 bitmap_from_arr32(chip->state, state, 64);
599
600 /* Update GPIO direction shadow register with default value */
601 of_property_read_u32(np, "xlnx,tri-default", &dir[0]);
602 of_property_read_u32(np, "xlnx,tri-default-2", &dir[1]);
603
604 bitmap_from_arr32(chip->dir, dir, 64);
605
606 /*
607 * Check device node and parent device node for device width
608 * and assume default width of 32
609 */
610 if (of_property_read_u32(np, "xlnx,gpio-width", &width[0]))
611 width[0] = 32;
612
613 if (width[0] > 32)
614 return -EINVAL;
615
616 if (is_dual && of_property_read_u32(np, "xlnx,gpio2-width", &width[1]))
617 width[1] = 32;
618
619 if (width[1] > 32)
620 return -EINVAL;
621
622 /* Setup software pin mapping */
623 bitmap_set(chip->sw_map, 0, width[0] + width[1]);
624
625 /* Setup hardware pin mapping */
626 bitmap_set(chip->hw_map, 0, width[0]);
627 bitmap_set(chip->hw_map, 32, width[1]);
628
629 spin_lock_init(&chip->gpio_lock);
630
631 chip->gc.base = -1;
632 chip->gc.ngpio = bitmap_weight(chip->hw_map, 64);
633 chip->gc.parent = &pdev->dev;
634 chip->gc.direction_input = xgpio_dir_in;
635 chip->gc.direction_output = xgpio_dir_out;
636 chip->gc.get = xgpio_get;
637 chip->gc.set = xgpio_set;
638 chip->gc.request = xgpio_request;
639 chip->gc.free = xgpio_free;
640 chip->gc.set_multiple = xgpio_set_multiple;
641
642 chip->gc.label = dev_name(&pdev->dev);
643
644 chip->regs = devm_platform_ioremap_resource(pdev, 0);
645 if (IS_ERR(chip->regs)) {
646 dev_err(&pdev->dev, "failed to ioremap memory resource\n");
647 return PTR_ERR(chip->regs);
648 }
649
650 chip->clk = devm_clk_get_optional(&pdev->dev, NULL);
651 if (IS_ERR(chip->clk))
652 return dev_err_probe(&pdev->dev, PTR_ERR(chip->clk), "input clock not found.\n");
653
654 status = clk_prepare_enable(chip->clk);
655 if (status < 0) {
656 dev_err(&pdev->dev, "Failed to prepare clk\n");
657 return status;
658 }
659 pm_runtime_get_noresume(&pdev->dev);
660 pm_runtime_set_active(&pdev->dev);
661 pm_runtime_enable(&pdev->dev);
662
663 xgpio_save_regs(chip);
664
665 chip->irq = platform_get_irq_optional(pdev, 0);
666 if (chip->irq <= 0)
667 goto skip_irq;
668
669 /* Disable per-channel interrupts */
670 xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, 0);
671 /* Clear any existing per-channel interrupts */
672 temp = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
673 xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, temp);
674 /* Enable global interrupts */
675 xgpio_writereg(chip->regs + XGPIO_GIER_OFFSET, XGPIO_GIER_IE);
676
677 girq = &chip->gc.irq;
678 gpio_irq_chip_set_chip(girq, &xgpio_irq_chip);
679 girq->parent_handler = xgpio_irqhandler;
680 girq->num_parents = 1;
681 girq->parents = devm_kcalloc(&pdev->dev, 1,
682 sizeof(*girq->parents),
683 GFP_KERNEL);
684 if (!girq->parents) {
685 status = -ENOMEM;
686 goto err_pm_put;
687 }
688 girq->parents[0] = chip->irq;
689 girq->default_type = IRQ_TYPE_NONE;
690 girq->handler = handle_bad_irq;
691
692 skip_irq:
693 status = devm_gpiochip_add_data(&pdev->dev, &chip->gc, chip);
694 if (status) {
695 dev_err(&pdev->dev, "failed to add GPIO chip\n");
696 goto err_pm_put;
697 }
698
699 pm_runtime_put(&pdev->dev);
700 return 0;
701
702 err_pm_put:
703 pm_runtime_disable(&pdev->dev);
704 pm_runtime_put_noidle(&pdev->dev);
705 clk_disable_unprepare(chip->clk);
706 return status;
707 }
708
709 static const struct of_device_id xgpio_of_match[] = {
710 { .compatible = "xlnx,xps-gpio-1.00.a", },
711 { /* end of list */ },
712 };
713
714 MODULE_DEVICE_TABLE(of, xgpio_of_match);
715
716 static struct platform_driver xgpio_plat_driver = {
717 .probe = xgpio_probe,
718 .remove = xgpio_remove,
719 .driver = {
720 .name = "gpio-xilinx",
721 .of_match_table = xgpio_of_match,
722 .pm = &xgpio_dev_pm_ops,
723 },
724 };
725
xgpio_init(void)726 static int __init xgpio_init(void)
727 {
728 return platform_driver_register(&xgpio_plat_driver);
729 }
730
731 subsys_initcall(xgpio_init);
732
xgpio_exit(void)733 static void __exit xgpio_exit(void)
734 {
735 platform_driver_unregister(&xgpio_plat_driver);
736 }
737 module_exit(xgpio_exit);
738
739 MODULE_AUTHOR("Xilinx, Inc.");
740 MODULE_DESCRIPTION("Xilinx GPIO driver");
741 MODULE_LICENSE("GPL");
742