xref: /openbmc/linux/drivers/gpio/gpio-pca953x.c (revision 4ee812f6)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  *  PCA953x 4/8/16/24/40 bit I/O ports
4  *
5  *  Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
6  *  Copyright (C) 2007 Marvell International Ltd.
7  *
8  *  Derived from drivers/i2c/chips/pca9539.c
9  */
10 
11 #include <linux/acpi.h>
12 #include <linux/bits.h>
13 #include <linux/gpio/driver.h>
14 #include <linux/gpio/consumer.h>
15 #include <linux/i2c.h>
16 #include <linux/init.h>
17 #include <linux/interrupt.h>
18 #include <linux/module.h>
19 #include <linux/of_platform.h>
20 #include <linux/platform_data/pca953x.h>
21 #include <linux/regmap.h>
22 #include <linux/regulator/consumer.h>
23 #include <linux/slab.h>
24 
25 #include <asm/unaligned.h>
26 
27 #define PCA953X_INPUT		0x00
28 #define PCA953X_OUTPUT		0x01
29 #define PCA953X_INVERT		0x02
30 #define PCA953X_DIRECTION	0x03
31 
32 #define REG_ADDR_MASK		GENMASK(5, 0)
33 #define REG_ADDR_EXT		BIT(6)
34 #define REG_ADDR_AI		BIT(7)
35 
36 #define PCA957X_IN		0x00
37 #define PCA957X_INVRT		0x01
38 #define PCA957X_BKEN		0x02
39 #define PCA957X_PUPD		0x03
40 #define PCA957X_CFG		0x04
41 #define PCA957X_OUT		0x05
42 #define PCA957X_MSK		0x06
43 #define PCA957X_INTS		0x07
44 
45 #define PCAL953X_OUT_STRENGTH	0x20
46 #define PCAL953X_IN_LATCH	0x22
47 #define PCAL953X_PULL_EN	0x23
48 #define PCAL953X_PULL_SEL	0x24
49 #define PCAL953X_INT_MASK	0x25
50 #define PCAL953X_INT_STAT	0x26
51 #define PCAL953X_OUT_CONF	0x27
52 
53 #define PCAL6524_INT_EDGE	0x28
54 #define PCAL6524_INT_CLR	0x2a
55 #define PCAL6524_IN_STATUS	0x2b
56 #define PCAL6524_OUT_INDCONF	0x2c
57 #define PCAL6524_DEBOUNCE	0x2d
58 
59 #define PCA_GPIO_MASK		GENMASK(7, 0)
60 
61 #define PCAL_GPIO_MASK		GENMASK(4, 0)
62 #define PCAL_PINCTRL_MASK	GENMASK(6, 5)
63 
64 #define PCA_INT			BIT(8)
65 #define PCA_PCAL		BIT(9)
66 #define PCA_LATCH_INT		(PCA_PCAL | PCA_INT)
67 #define PCA953X_TYPE		BIT(12)
68 #define PCA957X_TYPE		BIT(13)
69 #define PCA_TYPE_MASK		GENMASK(15, 12)
70 
71 #define PCA_CHIP_TYPE(x)	((x) & PCA_TYPE_MASK)
72 
73 static const struct i2c_device_id pca953x_id[] = {
74 	{ "pca6416", 16 | PCA953X_TYPE | PCA_INT, },
75 	{ "pca9505", 40 | PCA953X_TYPE | PCA_INT, },
76 	{ "pca9534", 8  | PCA953X_TYPE | PCA_INT, },
77 	{ "pca9535", 16 | PCA953X_TYPE | PCA_INT, },
78 	{ "pca9536", 4  | PCA953X_TYPE, },
79 	{ "pca9537", 4  | PCA953X_TYPE | PCA_INT, },
80 	{ "pca9538", 8  | PCA953X_TYPE | PCA_INT, },
81 	{ "pca9539", 16 | PCA953X_TYPE | PCA_INT, },
82 	{ "pca9554", 8  | PCA953X_TYPE | PCA_INT, },
83 	{ "pca9555", 16 | PCA953X_TYPE | PCA_INT, },
84 	{ "pca9556", 8  | PCA953X_TYPE, },
85 	{ "pca9557", 8  | PCA953X_TYPE, },
86 	{ "pca9574", 8  | PCA957X_TYPE | PCA_INT, },
87 	{ "pca9575", 16 | PCA957X_TYPE | PCA_INT, },
88 	{ "pca9698", 40 | PCA953X_TYPE, },
89 
90 	{ "pcal6416", 16 | PCA953X_TYPE | PCA_LATCH_INT, },
91 	{ "pcal6524", 24 | PCA953X_TYPE | PCA_LATCH_INT, },
92 	{ "pcal9555a", 16 | PCA953X_TYPE | PCA_LATCH_INT, },
93 
94 	{ "max7310", 8  | PCA953X_TYPE, },
95 	{ "max7312", 16 | PCA953X_TYPE | PCA_INT, },
96 	{ "max7313", 16 | PCA953X_TYPE | PCA_INT, },
97 	{ "max7315", 8  | PCA953X_TYPE | PCA_INT, },
98 	{ "max7318", 16 | PCA953X_TYPE | PCA_INT, },
99 	{ "pca6107", 8  | PCA953X_TYPE | PCA_INT, },
100 	{ "tca6408", 8  | PCA953X_TYPE | PCA_INT, },
101 	{ "tca6416", 16 | PCA953X_TYPE | PCA_INT, },
102 	{ "tca6424", 24 | PCA953X_TYPE | PCA_INT, },
103 	{ "tca9539", 16 | PCA953X_TYPE | PCA_INT, },
104 	{ "tca9554", 8  | PCA953X_TYPE | PCA_INT, },
105 	{ "xra1202", 8  | PCA953X_TYPE },
106 	{ }
107 };
108 MODULE_DEVICE_TABLE(i2c, pca953x_id);
109 
110 static const struct acpi_device_id pca953x_acpi_ids[] = {
111 	{ "INT3491", 16 | PCA953X_TYPE | PCA_LATCH_INT, },
112 	{ }
113 };
114 MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids);
115 
116 #define MAX_BANK 5
117 #define BANK_SZ 8
118 
119 #define NBANK(chip) DIV_ROUND_UP(chip->gpio_chip.ngpio, BANK_SZ)
120 
121 struct pca953x_reg_config {
122 	int direction;
123 	int output;
124 	int input;
125 	int invert;
126 };
127 
128 static const struct pca953x_reg_config pca953x_regs = {
129 	.direction = PCA953X_DIRECTION,
130 	.output = PCA953X_OUTPUT,
131 	.input = PCA953X_INPUT,
132 	.invert = PCA953X_INVERT,
133 };
134 
135 static const struct pca953x_reg_config pca957x_regs = {
136 	.direction = PCA957X_CFG,
137 	.output = PCA957X_OUT,
138 	.input = PCA957X_IN,
139 	.invert = PCA957X_INVRT,
140 };
141 
142 struct pca953x_chip {
143 	unsigned gpio_start;
144 	struct mutex i2c_lock;
145 	struct regmap *regmap;
146 
147 #ifdef CONFIG_GPIO_PCA953X_IRQ
148 	struct mutex irq_lock;
149 	u8 irq_mask[MAX_BANK];
150 	u8 irq_stat[MAX_BANK];
151 	u8 irq_trig_raise[MAX_BANK];
152 	u8 irq_trig_fall[MAX_BANK];
153 	struct irq_chip irq_chip;
154 #endif
155 	atomic_t wakeup_path;
156 
157 	struct i2c_client *client;
158 	struct gpio_chip gpio_chip;
159 	const char *const *names;
160 	unsigned long driver_data;
161 	struct regulator *regulator;
162 
163 	const struct pca953x_reg_config *regs;
164 };
165 
166 static int pca953x_bank_shift(struct pca953x_chip *chip)
167 {
168 	return fls((chip->gpio_chip.ngpio - 1) / BANK_SZ);
169 }
170 
171 #define PCA953x_BANK_INPUT	BIT(0)
172 #define PCA953x_BANK_OUTPUT	BIT(1)
173 #define PCA953x_BANK_POLARITY	BIT(2)
174 #define PCA953x_BANK_CONFIG	BIT(3)
175 
176 #define PCA957x_BANK_INPUT	BIT(0)
177 #define PCA957x_BANK_POLARITY	BIT(1)
178 #define PCA957x_BANK_BUSHOLD	BIT(2)
179 #define PCA957x_BANK_CONFIG	BIT(4)
180 #define PCA957x_BANK_OUTPUT	BIT(5)
181 
182 #define PCAL9xxx_BANK_IN_LATCH	BIT(8 + 2)
183 #define PCAL9xxx_BANK_PULL_EN	BIT(8 + 3)
184 #define PCAL9xxx_BANK_PULL_SEL	BIT(8 + 4)
185 #define PCAL9xxx_BANK_IRQ_MASK	BIT(8 + 5)
186 #define PCAL9xxx_BANK_IRQ_STAT	BIT(8 + 6)
187 
188 /*
189  * We care about the following registers:
190  * - Standard set, below 0x40, each port can be replicated up to 8 times
191  *   - PCA953x standard
192  *     Input port			0x00 + 0 * bank_size	R
193  *     Output port			0x00 + 1 * bank_size	RW
194  *     Polarity Inversion port		0x00 + 2 * bank_size	RW
195  *     Configuration port		0x00 + 3 * bank_size	RW
196  *   - PCA957x with mixed up registers
197  *     Input port			0x00 + 0 * bank_size	R
198  *     Polarity Inversion port		0x00 + 1 * bank_size	RW
199  *     Bus hold port			0x00 + 2 * bank_size	RW
200  *     Configuration port		0x00 + 4 * bank_size	RW
201  *     Output port			0x00 + 5 * bank_size	RW
202  *
203  * - Extended set, above 0x40, often chip specific.
204  *   - PCAL6524/PCAL9555A with custom PCAL IRQ handling:
205  *     Input latch register		0x40 + 2 * bank_size	RW
206  *     Pull-up/pull-down enable reg	0x40 + 3 * bank_size    RW
207  *     Pull-up/pull-down select reg	0x40 + 4 * bank_size    RW
208  *     Interrupt mask register		0x40 + 5 * bank_size	RW
209  *     Interrupt status register	0x40 + 6 * bank_size	R
210  *
211  * - Registers with bit 0x80 set, the AI bit
212  *   The bit is cleared and the registers fall into one of the
213  *   categories above.
214  */
215 
216 static bool pca953x_check_register(struct pca953x_chip *chip, unsigned int reg,
217 				   u32 checkbank)
218 {
219 	int bank_shift = pca953x_bank_shift(chip);
220 	int bank = (reg & REG_ADDR_MASK) >> bank_shift;
221 	int offset = reg & (BIT(bank_shift) - 1);
222 
223 	/* Special PCAL extended register check. */
224 	if (reg & REG_ADDR_EXT) {
225 		if (!(chip->driver_data & PCA_PCAL))
226 			return false;
227 		bank += 8;
228 	}
229 
230 	/* Register is not in the matching bank. */
231 	if (!(BIT(bank) & checkbank))
232 		return false;
233 
234 	/* Register is not within allowed range of bank. */
235 	if (offset >= NBANK(chip))
236 		return false;
237 
238 	return true;
239 }
240 
241 static bool pca953x_readable_register(struct device *dev, unsigned int reg)
242 {
243 	struct pca953x_chip *chip = dev_get_drvdata(dev);
244 	u32 bank;
245 
246 	if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE) {
247 		bank = PCA953x_BANK_INPUT | PCA953x_BANK_OUTPUT |
248 		       PCA953x_BANK_POLARITY | PCA953x_BANK_CONFIG;
249 	} else {
250 		bank = PCA957x_BANK_INPUT | PCA957x_BANK_OUTPUT |
251 		       PCA957x_BANK_POLARITY | PCA957x_BANK_CONFIG |
252 		       PCA957x_BANK_BUSHOLD;
253 	}
254 
255 	if (chip->driver_data & PCA_PCAL) {
256 		bank |= PCAL9xxx_BANK_IN_LATCH | PCAL9xxx_BANK_PULL_EN |
257 			PCAL9xxx_BANK_PULL_SEL | PCAL9xxx_BANK_IRQ_MASK |
258 			PCAL9xxx_BANK_IRQ_STAT;
259 	}
260 
261 	return pca953x_check_register(chip, reg, bank);
262 }
263 
264 static bool pca953x_writeable_register(struct device *dev, unsigned int reg)
265 {
266 	struct pca953x_chip *chip = dev_get_drvdata(dev);
267 	u32 bank;
268 
269 	if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE) {
270 		bank = PCA953x_BANK_OUTPUT | PCA953x_BANK_POLARITY |
271 			PCA953x_BANK_CONFIG;
272 	} else {
273 		bank = PCA957x_BANK_OUTPUT | PCA957x_BANK_POLARITY |
274 			PCA957x_BANK_CONFIG | PCA957x_BANK_BUSHOLD;
275 	}
276 
277 	if (chip->driver_data & PCA_PCAL)
278 		bank |= PCAL9xxx_BANK_IN_LATCH | PCAL9xxx_BANK_PULL_EN |
279 			PCAL9xxx_BANK_PULL_SEL | PCAL9xxx_BANK_IRQ_MASK;
280 
281 	return pca953x_check_register(chip, reg, bank);
282 }
283 
284 static bool pca953x_volatile_register(struct device *dev, unsigned int reg)
285 {
286 	struct pca953x_chip *chip = dev_get_drvdata(dev);
287 	u32 bank;
288 
289 	if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE)
290 		bank = PCA953x_BANK_INPUT;
291 	else
292 		bank = PCA957x_BANK_INPUT;
293 
294 	if (chip->driver_data & PCA_PCAL)
295 		bank |= PCAL9xxx_BANK_IRQ_STAT;
296 
297 	return pca953x_check_register(chip, reg, bank);
298 }
299 
300 static const struct regmap_config pca953x_i2c_regmap = {
301 	.reg_bits = 8,
302 	.val_bits = 8,
303 
304 	.readable_reg = pca953x_readable_register,
305 	.writeable_reg = pca953x_writeable_register,
306 	.volatile_reg = pca953x_volatile_register,
307 
308 	.cache_type = REGCACHE_RBTREE,
309 	/* REVISIT: should be 0x7f but some 24 bit chips use REG_ADDR_AI */
310 	.max_register = 0xff,
311 };
312 
313 static u8 pca953x_recalc_addr(struct pca953x_chip *chip, int reg, int off,
314 			      bool write, bool addrinc)
315 {
316 	int bank_shift = pca953x_bank_shift(chip);
317 	int addr = (reg & PCAL_GPIO_MASK) << bank_shift;
318 	int pinctrl = (reg & PCAL_PINCTRL_MASK) << 1;
319 	u8 regaddr = pinctrl | addr | (off / BANK_SZ);
320 
321 	/* Single byte read doesn't need AI bit set. */
322 	if (!addrinc)
323 		return regaddr;
324 
325 	/* Chips with 24 and more GPIOs always support Auto Increment */
326 	if (write && NBANK(chip) > 2)
327 		regaddr |= REG_ADDR_AI;
328 
329 	/* PCA9575 needs address-increment on multi-byte writes */
330 	if (PCA_CHIP_TYPE(chip->driver_data) == PCA957X_TYPE)
331 		regaddr |= REG_ADDR_AI;
332 
333 	return regaddr;
334 }
335 
336 static int pca953x_write_regs(struct pca953x_chip *chip, int reg, u8 *val)
337 {
338 	u8 regaddr = pca953x_recalc_addr(chip, reg, 0, true, true);
339 	int ret;
340 
341 	ret = regmap_bulk_write(chip->regmap, regaddr, val, NBANK(chip));
342 	if (ret < 0) {
343 		dev_err(&chip->client->dev, "failed writing register\n");
344 		return ret;
345 	}
346 
347 	return 0;
348 }
349 
350 static int pca953x_read_regs(struct pca953x_chip *chip, int reg, u8 *val)
351 {
352 	u8 regaddr = pca953x_recalc_addr(chip, reg, 0, false, true);
353 	int ret;
354 
355 	ret = regmap_bulk_read(chip->regmap, regaddr, val, NBANK(chip));
356 	if (ret < 0) {
357 		dev_err(&chip->client->dev, "failed reading register\n");
358 		return ret;
359 	}
360 
361 	return 0;
362 }
363 
364 static int pca953x_gpio_direction_input(struct gpio_chip *gc, unsigned off)
365 {
366 	struct pca953x_chip *chip = gpiochip_get_data(gc);
367 	u8 dirreg = pca953x_recalc_addr(chip, chip->regs->direction, off,
368 					true, false);
369 	u8 bit = BIT(off % BANK_SZ);
370 	int ret;
371 
372 	mutex_lock(&chip->i2c_lock);
373 	ret = regmap_write_bits(chip->regmap, dirreg, bit, bit);
374 	mutex_unlock(&chip->i2c_lock);
375 	return ret;
376 }
377 
378 static int pca953x_gpio_direction_output(struct gpio_chip *gc,
379 		unsigned off, int val)
380 {
381 	struct pca953x_chip *chip = gpiochip_get_data(gc);
382 	u8 dirreg = pca953x_recalc_addr(chip, chip->regs->direction, off,
383 					true, false);
384 	u8 outreg = pca953x_recalc_addr(chip, chip->regs->output, off,
385 					true, false);
386 	u8 bit = BIT(off % BANK_SZ);
387 	int ret;
388 
389 	mutex_lock(&chip->i2c_lock);
390 	/* set output level */
391 	ret = regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0);
392 	if (ret)
393 		goto exit;
394 
395 	/* then direction */
396 	ret = regmap_write_bits(chip->regmap, dirreg, bit, 0);
397 exit:
398 	mutex_unlock(&chip->i2c_lock);
399 	return ret;
400 }
401 
402 static int pca953x_gpio_get_value(struct gpio_chip *gc, unsigned off)
403 {
404 	struct pca953x_chip *chip = gpiochip_get_data(gc);
405 	u8 inreg = pca953x_recalc_addr(chip, chip->regs->input, off,
406 				       true, false);
407 	u8 bit = BIT(off % BANK_SZ);
408 	u32 reg_val;
409 	int ret;
410 
411 	mutex_lock(&chip->i2c_lock);
412 	ret = regmap_read(chip->regmap, inreg, &reg_val);
413 	mutex_unlock(&chip->i2c_lock);
414 	if (ret < 0) {
415 		/* NOTE:  diagnostic already emitted; that's all we should
416 		 * do unless gpio_*_value_cansleep() calls become different
417 		 * from their nonsleeping siblings (and report faults).
418 		 */
419 		return 0;
420 	}
421 
422 	return !!(reg_val & bit);
423 }
424 
425 static void pca953x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
426 {
427 	struct pca953x_chip *chip = gpiochip_get_data(gc);
428 	u8 outreg = pca953x_recalc_addr(chip, chip->regs->output, off,
429 					true, false);
430 	u8 bit = BIT(off % BANK_SZ);
431 
432 	mutex_lock(&chip->i2c_lock);
433 	regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0);
434 	mutex_unlock(&chip->i2c_lock);
435 }
436 
437 static int pca953x_gpio_get_direction(struct gpio_chip *gc, unsigned off)
438 {
439 	struct pca953x_chip *chip = gpiochip_get_data(gc);
440 	u8 dirreg = pca953x_recalc_addr(chip, chip->regs->direction, off,
441 					true, false);
442 	u8 bit = BIT(off % BANK_SZ);
443 	u32 reg_val;
444 	int ret;
445 
446 	mutex_lock(&chip->i2c_lock);
447 	ret = regmap_read(chip->regmap, dirreg, &reg_val);
448 	mutex_unlock(&chip->i2c_lock);
449 	if (ret < 0)
450 		return ret;
451 
452 	return !!(reg_val & bit);
453 }
454 
455 static void pca953x_gpio_set_multiple(struct gpio_chip *gc,
456 				      unsigned long *mask, unsigned long *bits)
457 {
458 	struct pca953x_chip *chip = gpiochip_get_data(gc);
459 	unsigned int bank_mask, bank_val;
460 	int bank;
461 	u8 reg_val[MAX_BANK];
462 	int ret;
463 
464 	mutex_lock(&chip->i2c_lock);
465 	ret = pca953x_read_regs(chip, chip->regs->output, reg_val);
466 	if (ret)
467 		goto exit;
468 
469 	for (bank = 0; bank < NBANK(chip); bank++) {
470 		bank_mask = mask[bank / sizeof(*mask)] >>
471 			   ((bank % sizeof(*mask)) * 8);
472 		if (bank_mask) {
473 			bank_val = bits[bank / sizeof(*bits)] >>
474 				  ((bank % sizeof(*bits)) * 8);
475 			bank_val &= bank_mask;
476 			reg_val[bank] = (reg_val[bank] & ~bank_mask) | bank_val;
477 		}
478 	}
479 
480 	pca953x_write_regs(chip, chip->regs->output, reg_val);
481 exit:
482 	mutex_unlock(&chip->i2c_lock);
483 }
484 
485 static int pca953x_gpio_set_pull_up_down(struct pca953x_chip *chip,
486 					 unsigned int offset,
487 					 unsigned long config)
488 {
489 	u8 pull_en_reg = pca953x_recalc_addr(chip, PCAL953X_PULL_EN, offset,
490 					     true, false);
491 	u8 pull_sel_reg = pca953x_recalc_addr(chip, PCAL953X_PULL_SEL, offset,
492 					      true, false);
493 	u8 bit = BIT(offset % BANK_SZ);
494 	int ret;
495 
496 	/*
497 	 * pull-up/pull-down configuration requires PCAL extended
498 	 * registers
499 	 */
500 	if (!(chip->driver_data & PCA_PCAL))
501 		return -ENOTSUPP;
502 
503 	mutex_lock(&chip->i2c_lock);
504 
505 	/* Disable pull-up/pull-down */
506 	ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, 0);
507 	if (ret)
508 		goto exit;
509 
510 	/* Configure pull-up/pull-down */
511 	if (config == PIN_CONFIG_BIAS_PULL_UP)
512 		ret = regmap_write_bits(chip->regmap, pull_sel_reg, bit, bit);
513 	else if (config == PIN_CONFIG_BIAS_PULL_DOWN)
514 		ret = regmap_write_bits(chip->regmap, pull_sel_reg, bit, 0);
515 	if (ret)
516 		goto exit;
517 
518 	/* Enable pull-up/pull-down */
519 	ret = regmap_write_bits(chip->regmap, pull_en_reg, bit, bit);
520 
521 exit:
522 	mutex_unlock(&chip->i2c_lock);
523 	return ret;
524 }
525 
526 static int pca953x_gpio_set_config(struct gpio_chip *gc, unsigned int offset,
527 				   unsigned long config)
528 {
529 	struct pca953x_chip *chip = gpiochip_get_data(gc);
530 
531 	switch (config) {
532 	case PIN_CONFIG_BIAS_PULL_UP:
533 	case PIN_CONFIG_BIAS_PULL_DOWN:
534 		return pca953x_gpio_set_pull_up_down(chip, offset, config);
535 	default:
536 		return -ENOTSUPP;
537 	}
538 }
539 
540 static void pca953x_setup_gpio(struct pca953x_chip *chip, int gpios)
541 {
542 	struct gpio_chip *gc;
543 
544 	gc = &chip->gpio_chip;
545 
546 	gc->direction_input  = pca953x_gpio_direction_input;
547 	gc->direction_output = pca953x_gpio_direction_output;
548 	gc->get = pca953x_gpio_get_value;
549 	gc->set = pca953x_gpio_set_value;
550 	gc->get_direction = pca953x_gpio_get_direction;
551 	gc->set_multiple = pca953x_gpio_set_multiple;
552 	gc->set_config = pca953x_gpio_set_config;
553 	gc->can_sleep = true;
554 
555 	gc->base = chip->gpio_start;
556 	gc->ngpio = gpios;
557 	gc->label = dev_name(&chip->client->dev);
558 	gc->parent = &chip->client->dev;
559 	gc->owner = THIS_MODULE;
560 	gc->names = chip->names;
561 }
562 
563 #ifdef CONFIG_GPIO_PCA953X_IRQ
564 static void pca953x_irq_mask(struct irq_data *d)
565 {
566 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
567 	struct pca953x_chip *chip = gpiochip_get_data(gc);
568 
569 	chip->irq_mask[d->hwirq / BANK_SZ] &= ~BIT(d->hwirq % BANK_SZ);
570 }
571 
572 static void pca953x_irq_unmask(struct irq_data *d)
573 {
574 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
575 	struct pca953x_chip *chip = gpiochip_get_data(gc);
576 
577 	chip->irq_mask[d->hwirq / BANK_SZ] |= BIT(d->hwirq % BANK_SZ);
578 }
579 
580 static int pca953x_irq_set_wake(struct irq_data *d, unsigned int on)
581 {
582 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
583 	struct pca953x_chip *chip = gpiochip_get_data(gc);
584 
585 	if (on)
586 		atomic_inc(&chip->wakeup_path);
587 	else
588 		atomic_dec(&chip->wakeup_path);
589 
590 	return irq_set_irq_wake(chip->client->irq, on);
591 }
592 
593 static void pca953x_irq_bus_lock(struct irq_data *d)
594 {
595 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
596 	struct pca953x_chip *chip = gpiochip_get_data(gc);
597 
598 	mutex_lock(&chip->irq_lock);
599 }
600 
601 static void pca953x_irq_bus_sync_unlock(struct irq_data *d)
602 {
603 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
604 	struct pca953x_chip *chip = gpiochip_get_data(gc);
605 	u8 new_irqs;
606 	int level, i;
607 	u8 invert_irq_mask[MAX_BANK];
608 	u8 reg_direction[MAX_BANK];
609 
610 	pca953x_read_regs(chip, chip->regs->direction, reg_direction);
611 
612 	if (chip->driver_data & PCA_PCAL) {
613 		/* Enable latch on interrupt-enabled inputs */
614 		pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip->irq_mask);
615 
616 		for (i = 0; i < NBANK(chip); i++)
617 			invert_irq_mask[i] = ~chip->irq_mask[i];
618 
619 		/* Unmask enabled interrupts */
620 		pca953x_write_regs(chip, PCAL953X_INT_MASK, invert_irq_mask);
621 	}
622 
623 	/* Look for any newly setup interrupt */
624 	for (i = 0; i < NBANK(chip); i++) {
625 		new_irqs = chip->irq_trig_fall[i] | chip->irq_trig_raise[i];
626 		new_irqs &= reg_direction[i];
627 
628 		while (new_irqs) {
629 			level = __ffs(new_irqs);
630 			pca953x_gpio_direction_input(&chip->gpio_chip,
631 							level + (BANK_SZ * i));
632 			new_irqs &= ~(1 << level);
633 		}
634 	}
635 
636 	mutex_unlock(&chip->irq_lock);
637 }
638 
639 static int pca953x_irq_set_type(struct irq_data *d, unsigned int type)
640 {
641 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
642 	struct pca953x_chip *chip = gpiochip_get_data(gc);
643 	int bank_nb = d->hwirq / BANK_SZ;
644 	u8 mask = BIT(d->hwirq % BANK_SZ);
645 
646 	if (!(type & IRQ_TYPE_EDGE_BOTH)) {
647 		dev_err(&chip->client->dev, "irq %d: unsupported type %d\n",
648 			d->irq, type);
649 		return -EINVAL;
650 	}
651 
652 	if (type & IRQ_TYPE_EDGE_FALLING)
653 		chip->irq_trig_fall[bank_nb] |= mask;
654 	else
655 		chip->irq_trig_fall[bank_nb] &= ~mask;
656 
657 	if (type & IRQ_TYPE_EDGE_RISING)
658 		chip->irq_trig_raise[bank_nb] |= mask;
659 	else
660 		chip->irq_trig_raise[bank_nb] &= ~mask;
661 
662 	return 0;
663 }
664 
665 static void pca953x_irq_shutdown(struct irq_data *d)
666 {
667 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
668 	struct pca953x_chip *chip = gpiochip_get_data(gc);
669 	u8 mask = BIT(d->hwirq % BANK_SZ);
670 
671 	chip->irq_trig_raise[d->hwirq / BANK_SZ] &= ~mask;
672 	chip->irq_trig_fall[d->hwirq / BANK_SZ] &= ~mask;
673 }
674 
675 static bool pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending)
676 {
677 	u8 cur_stat[MAX_BANK];
678 	u8 old_stat[MAX_BANK];
679 	bool pending_seen = false;
680 	bool trigger_seen = false;
681 	u8 trigger[MAX_BANK];
682 	u8 reg_direction[MAX_BANK];
683 	int ret, i;
684 
685 	if (chip->driver_data & PCA_PCAL) {
686 		/* Read the current interrupt status from the device */
687 		ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger);
688 		if (ret)
689 			return false;
690 
691 		/* Check latched inputs and clear interrupt status */
692 		ret = pca953x_read_regs(chip, PCA953X_INPUT, cur_stat);
693 		if (ret)
694 			return false;
695 
696 		for (i = 0; i < NBANK(chip); i++) {
697 			/* Apply filter for rising/falling edge selection */
698 			pending[i] = (~cur_stat[i] & chip->irq_trig_fall[i]) |
699 				(cur_stat[i] & chip->irq_trig_raise[i]);
700 			pending[i] &= trigger[i];
701 			if (pending[i])
702 				pending_seen = true;
703 		}
704 
705 		return pending_seen;
706 	}
707 
708 	ret = pca953x_read_regs(chip, chip->regs->input, cur_stat);
709 	if (ret)
710 		return false;
711 
712 	/* Remove output pins from the equation */
713 	pca953x_read_regs(chip, chip->regs->direction, reg_direction);
714 	for (i = 0; i < NBANK(chip); i++)
715 		cur_stat[i] &= reg_direction[i];
716 
717 	memcpy(old_stat, chip->irq_stat, NBANK(chip));
718 
719 	for (i = 0; i < NBANK(chip); i++) {
720 		trigger[i] = (cur_stat[i] ^ old_stat[i]) & chip->irq_mask[i];
721 		if (trigger[i])
722 			trigger_seen = true;
723 	}
724 
725 	if (!trigger_seen)
726 		return false;
727 
728 	memcpy(chip->irq_stat, cur_stat, NBANK(chip));
729 
730 	for (i = 0; i < NBANK(chip); i++) {
731 		pending[i] = (old_stat[i] & chip->irq_trig_fall[i]) |
732 			(cur_stat[i] & chip->irq_trig_raise[i]);
733 		pending[i] &= trigger[i];
734 		if (pending[i])
735 			pending_seen = true;
736 	}
737 
738 	return pending_seen;
739 }
740 
741 static irqreturn_t pca953x_irq_handler(int irq, void *devid)
742 {
743 	struct pca953x_chip *chip = devid;
744 	u8 pending[MAX_BANK];
745 	u8 level;
746 	unsigned nhandled = 0;
747 	int i;
748 
749 	if (!pca953x_irq_pending(chip, pending))
750 		return IRQ_NONE;
751 
752 	for (i = 0; i < NBANK(chip); i++) {
753 		while (pending[i]) {
754 			level = __ffs(pending[i]);
755 			handle_nested_irq(irq_find_mapping(chip->gpio_chip.irq.domain,
756 							level + (BANK_SZ * i)));
757 			pending[i] &= ~(1 << level);
758 			nhandled++;
759 		}
760 	}
761 
762 	return (nhandled > 0) ? IRQ_HANDLED : IRQ_NONE;
763 }
764 
765 static int pca953x_irq_setup(struct pca953x_chip *chip,
766 			     int irq_base)
767 {
768 	struct i2c_client *client = chip->client;
769 	struct irq_chip *irq_chip = &chip->irq_chip;
770 	u8 reg_direction[MAX_BANK];
771 	int ret, i;
772 
773 	if (!client->irq)
774 		return 0;
775 
776 	if (irq_base == -1)
777 		return 0;
778 
779 	if (!(chip->driver_data & PCA_INT))
780 		return 0;
781 
782 	ret = pca953x_read_regs(chip, chip->regs->input, chip->irq_stat);
783 	if (ret)
784 		return ret;
785 
786 	/*
787 	 * There is no way to know which GPIO line generated the
788 	 * interrupt.  We have to rely on the previous read for
789 	 * this purpose.
790 	 */
791 	pca953x_read_regs(chip, chip->regs->direction, reg_direction);
792 	for (i = 0; i < NBANK(chip); i++)
793 		chip->irq_stat[i] &= reg_direction[i];
794 	mutex_init(&chip->irq_lock);
795 
796 	ret = devm_request_threaded_irq(&client->dev, client->irq,
797 					NULL, pca953x_irq_handler,
798 					IRQF_TRIGGER_LOW | IRQF_ONESHOT |
799 					IRQF_SHARED,
800 					dev_name(&client->dev), chip);
801 	if (ret) {
802 		dev_err(&client->dev, "failed to request irq %d\n",
803 			client->irq);
804 		return ret;
805 	}
806 
807 	irq_chip->name = dev_name(&chip->client->dev);
808 	irq_chip->irq_mask = pca953x_irq_mask;
809 	irq_chip->irq_unmask = pca953x_irq_unmask;
810 	irq_chip->irq_set_wake = pca953x_irq_set_wake;
811 	irq_chip->irq_bus_lock = pca953x_irq_bus_lock;
812 	irq_chip->irq_bus_sync_unlock = pca953x_irq_bus_sync_unlock;
813 	irq_chip->irq_set_type = pca953x_irq_set_type;
814 	irq_chip->irq_shutdown = pca953x_irq_shutdown;
815 
816 	ret =  gpiochip_irqchip_add_nested(&chip->gpio_chip, irq_chip,
817 					   irq_base, handle_simple_irq,
818 					   IRQ_TYPE_NONE);
819 	if (ret) {
820 		dev_err(&client->dev,
821 			"could not connect irqchip to gpiochip\n");
822 		return ret;
823 	}
824 
825 	gpiochip_set_nested_irqchip(&chip->gpio_chip, irq_chip, client->irq);
826 
827 	return 0;
828 }
829 
830 #else /* CONFIG_GPIO_PCA953X_IRQ */
831 static int pca953x_irq_setup(struct pca953x_chip *chip,
832 			     int irq_base)
833 {
834 	struct i2c_client *client = chip->client;
835 
836 	if (client->irq && irq_base != -1 && (chip->driver_data & PCA_INT))
837 		dev_warn(&client->dev, "interrupt support not compiled in\n");
838 
839 	return 0;
840 }
841 #endif
842 
843 static int device_pca95xx_init(struct pca953x_chip *chip, u32 invert)
844 {
845 	int ret;
846 	u8 val[MAX_BANK];
847 
848 	ret = regcache_sync_region(chip->regmap, chip->regs->output,
849 				   chip->regs->output + NBANK(chip));
850 	if (ret)
851 		goto out;
852 
853 	ret = regcache_sync_region(chip->regmap, chip->regs->direction,
854 				   chip->regs->direction + NBANK(chip));
855 	if (ret)
856 		goto out;
857 
858 	/* set platform specific polarity inversion */
859 	if (invert)
860 		memset(val, 0xFF, NBANK(chip));
861 	else
862 		memset(val, 0, NBANK(chip));
863 
864 	ret = pca953x_write_regs(chip, chip->regs->invert, val);
865 out:
866 	return ret;
867 }
868 
869 static int device_pca957x_init(struct pca953x_chip *chip, u32 invert)
870 {
871 	int ret;
872 	u8 val[MAX_BANK];
873 
874 	ret = device_pca95xx_init(chip, invert);
875 	if (ret)
876 		goto out;
877 
878 	/* To enable register 6, 7 to control pull up and pull down */
879 	memset(val, 0x02, NBANK(chip));
880 	ret = pca953x_write_regs(chip, PCA957X_BKEN, val);
881 	if (ret)
882 		goto out;
883 
884 	return 0;
885 out:
886 	return ret;
887 }
888 
889 static const struct of_device_id pca953x_dt_ids[];
890 
891 static int pca953x_probe(struct i2c_client *client,
892 				   const struct i2c_device_id *i2c_id)
893 {
894 	struct pca953x_platform_data *pdata;
895 	struct pca953x_chip *chip;
896 	int irq_base = 0;
897 	int ret;
898 	u32 invert = 0;
899 	struct regulator *reg;
900 
901 	chip = devm_kzalloc(&client->dev,
902 			sizeof(struct pca953x_chip), GFP_KERNEL);
903 	if (chip == NULL)
904 		return -ENOMEM;
905 
906 	pdata = dev_get_platdata(&client->dev);
907 	if (pdata) {
908 		irq_base = pdata->irq_base;
909 		chip->gpio_start = pdata->gpio_base;
910 		invert = pdata->invert;
911 		chip->names = pdata->names;
912 	} else {
913 		struct gpio_desc *reset_gpio;
914 
915 		chip->gpio_start = -1;
916 		irq_base = 0;
917 
918 		/*
919 		 * See if we need to de-assert a reset pin.
920 		 *
921 		 * There is no known ACPI-enabled platforms that are
922 		 * using "reset" GPIO. Otherwise any of those platform
923 		 * must use _DSD method with corresponding property.
924 		 */
925 		reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
926 						     GPIOD_OUT_LOW);
927 		if (IS_ERR(reset_gpio))
928 			return PTR_ERR(reset_gpio);
929 	}
930 
931 	chip->client = client;
932 
933 	reg = devm_regulator_get(&client->dev, "vcc");
934 	if (IS_ERR(reg)) {
935 		ret = PTR_ERR(reg);
936 		if (ret != -EPROBE_DEFER)
937 			dev_err(&client->dev, "reg get err: %d\n", ret);
938 		return ret;
939 	}
940 	ret = regulator_enable(reg);
941 	if (ret) {
942 		dev_err(&client->dev, "reg en err: %d\n", ret);
943 		return ret;
944 	}
945 	chip->regulator = reg;
946 
947 	if (i2c_id) {
948 		chip->driver_data = i2c_id->driver_data;
949 	} else {
950 		const void *match;
951 
952 		match = device_get_match_data(&client->dev);
953 		if (!match) {
954 			ret = -ENODEV;
955 			goto err_exit;
956 		}
957 
958 		chip->driver_data = (uintptr_t)match;
959 	}
960 
961 	i2c_set_clientdata(client, chip);
962 
963 	chip->regmap = devm_regmap_init_i2c(client, &pca953x_i2c_regmap);
964 	if (IS_ERR(chip->regmap)) {
965 		ret = PTR_ERR(chip->regmap);
966 		goto err_exit;
967 	}
968 
969 	regcache_mark_dirty(chip->regmap);
970 
971 	mutex_init(&chip->i2c_lock);
972 	/*
973 	 * In case we have an i2c-mux controlled by a GPIO provided by an
974 	 * expander using the same driver higher on the device tree, read the
975 	 * i2c adapter nesting depth and use the retrieved value as lockdep
976 	 * subclass for chip->i2c_lock.
977 	 *
978 	 * REVISIT: This solution is not complete. It protects us from lockdep
979 	 * false positives when the expander controlling the i2c-mux is on
980 	 * a different level on the device tree, but not when it's on the same
981 	 * level on a different branch (in which case the subclass number
982 	 * would be the same).
983 	 *
984 	 * TODO: Once a correct solution is developed, a similar fix should be
985 	 * applied to all other i2c-controlled GPIO expanders (and potentially
986 	 * regmap-i2c).
987 	 */
988 	lockdep_set_subclass(&chip->i2c_lock,
989 			     i2c_adapter_depth(client->adapter));
990 
991 	/* initialize cached registers from their original values.
992 	 * we can't share this chip with another i2c master.
993 	 */
994 	pca953x_setup_gpio(chip, chip->driver_data & PCA_GPIO_MASK);
995 
996 	if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE) {
997 		chip->regs = &pca953x_regs;
998 		ret = device_pca95xx_init(chip, invert);
999 	} else {
1000 		chip->regs = &pca957x_regs;
1001 		ret = device_pca957x_init(chip, invert);
1002 	}
1003 	if (ret)
1004 		goto err_exit;
1005 
1006 	ret = devm_gpiochip_add_data(&client->dev, &chip->gpio_chip, chip);
1007 	if (ret)
1008 		goto err_exit;
1009 
1010 	ret = pca953x_irq_setup(chip, irq_base);
1011 	if (ret)
1012 		goto err_exit;
1013 
1014 	if (pdata && pdata->setup) {
1015 		ret = pdata->setup(client, chip->gpio_chip.base,
1016 				chip->gpio_chip.ngpio, pdata->context);
1017 		if (ret < 0)
1018 			dev_warn(&client->dev, "setup failed, %d\n", ret);
1019 	}
1020 
1021 	return 0;
1022 
1023 err_exit:
1024 	regulator_disable(chip->regulator);
1025 	return ret;
1026 }
1027 
1028 static int pca953x_remove(struct i2c_client *client)
1029 {
1030 	struct pca953x_platform_data *pdata = dev_get_platdata(&client->dev);
1031 	struct pca953x_chip *chip = i2c_get_clientdata(client);
1032 	int ret;
1033 
1034 	if (pdata && pdata->teardown) {
1035 		ret = pdata->teardown(client, chip->gpio_chip.base,
1036 				chip->gpio_chip.ngpio, pdata->context);
1037 		if (ret < 0)
1038 			dev_err(&client->dev, "teardown failed, %d\n", ret);
1039 	} else {
1040 		ret = 0;
1041 	}
1042 
1043 	regulator_disable(chip->regulator);
1044 
1045 	return ret;
1046 }
1047 
1048 #ifdef CONFIG_PM_SLEEP
1049 static int pca953x_regcache_sync(struct device *dev)
1050 {
1051 	struct pca953x_chip *chip = dev_get_drvdata(dev);
1052 	int ret;
1053 
1054 	/*
1055 	 * The ordering between direction and output is important,
1056 	 * sync these registers first and only then sync the rest.
1057 	 */
1058 	ret = regcache_sync_region(chip->regmap, chip->regs->direction,
1059 				   chip->regs->direction + NBANK(chip));
1060 	if (ret) {
1061 		dev_err(dev, "Failed to sync GPIO dir registers: %d\n", ret);
1062 		return ret;
1063 	}
1064 
1065 	ret = regcache_sync_region(chip->regmap, chip->regs->output,
1066 				   chip->regs->output + NBANK(chip));
1067 	if (ret) {
1068 		dev_err(dev, "Failed to sync GPIO out registers: %d\n", ret);
1069 		return ret;
1070 	}
1071 
1072 #ifdef CONFIG_GPIO_PCA953X_IRQ
1073 	if (chip->driver_data & PCA_PCAL) {
1074 		ret = regcache_sync_region(chip->regmap, PCAL953X_IN_LATCH,
1075 					   PCAL953X_IN_LATCH + NBANK(chip));
1076 		if (ret) {
1077 			dev_err(dev, "Failed to sync INT latch registers: %d\n",
1078 				ret);
1079 			return ret;
1080 		}
1081 
1082 		ret = regcache_sync_region(chip->regmap, PCAL953X_INT_MASK,
1083 					   PCAL953X_INT_MASK + NBANK(chip));
1084 		if (ret) {
1085 			dev_err(dev, "Failed to sync INT mask registers: %d\n",
1086 				ret);
1087 			return ret;
1088 		}
1089 	}
1090 #endif
1091 
1092 	return 0;
1093 }
1094 
1095 static int pca953x_suspend(struct device *dev)
1096 {
1097 	struct pca953x_chip *chip = dev_get_drvdata(dev);
1098 
1099 	regcache_cache_only(chip->regmap, true);
1100 
1101 	if (atomic_read(&chip->wakeup_path))
1102 		device_set_wakeup_path(dev);
1103 	else
1104 		regulator_disable(chip->regulator);
1105 
1106 	return 0;
1107 }
1108 
1109 static int pca953x_resume(struct device *dev)
1110 {
1111 	struct pca953x_chip *chip = dev_get_drvdata(dev);
1112 	int ret;
1113 
1114 	if (!atomic_read(&chip->wakeup_path)) {
1115 		ret = regulator_enable(chip->regulator);
1116 		if (ret) {
1117 			dev_err(dev, "Failed to enable regulator: %d\n", ret);
1118 			return 0;
1119 		}
1120 	}
1121 
1122 	regcache_cache_only(chip->regmap, false);
1123 	regcache_mark_dirty(chip->regmap);
1124 	ret = pca953x_regcache_sync(dev);
1125 	if (ret)
1126 		return ret;
1127 
1128 	ret = regcache_sync(chip->regmap);
1129 	if (ret) {
1130 		dev_err(dev, "Failed to restore register map: %d\n", ret);
1131 		return ret;
1132 	}
1133 
1134 	return 0;
1135 }
1136 #endif
1137 
1138 /* convenience to stop overlong match-table lines */
1139 #define OF_953X(__nrgpio, __int) (void *)(__nrgpio | PCA953X_TYPE | __int)
1140 #define OF_957X(__nrgpio, __int) (void *)(__nrgpio | PCA957X_TYPE | __int)
1141 
1142 static const struct of_device_id pca953x_dt_ids[] = {
1143 	{ .compatible = "nxp,pca6416", .data = OF_953X(16, PCA_INT), },
1144 	{ .compatible = "nxp,pca9505", .data = OF_953X(40, PCA_INT), },
1145 	{ .compatible = "nxp,pca9534", .data = OF_953X( 8, PCA_INT), },
1146 	{ .compatible = "nxp,pca9535", .data = OF_953X(16, PCA_INT), },
1147 	{ .compatible = "nxp,pca9536", .data = OF_953X( 4, 0), },
1148 	{ .compatible = "nxp,pca9537", .data = OF_953X( 4, PCA_INT), },
1149 	{ .compatible = "nxp,pca9538", .data = OF_953X( 8, PCA_INT), },
1150 	{ .compatible = "nxp,pca9539", .data = OF_953X(16, PCA_INT), },
1151 	{ .compatible = "nxp,pca9554", .data = OF_953X( 8, PCA_INT), },
1152 	{ .compatible = "nxp,pca9555", .data = OF_953X(16, PCA_INT), },
1153 	{ .compatible = "nxp,pca9556", .data = OF_953X( 8, 0), },
1154 	{ .compatible = "nxp,pca9557", .data = OF_953X( 8, 0), },
1155 	{ .compatible = "nxp,pca9574", .data = OF_957X( 8, PCA_INT), },
1156 	{ .compatible = "nxp,pca9575", .data = OF_957X(16, PCA_INT), },
1157 	{ .compatible = "nxp,pca9698", .data = OF_953X(40, 0), },
1158 
1159 	{ .compatible = "nxp,pcal6416", .data = OF_953X(16, PCA_LATCH_INT), },
1160 	{ .compatible = "nxp,pcal6524", .data = OF_953X(24, PCA_LATCH_INT), },
1161 	{ .compatible = "nxp,pcal9555a", .data = OF_953X(16, PCA_LATCH_INT), },
1162 
1163 	{ .compatible = "maxim,max7310", .data = OF_953X( 8, 0), },
1164 	{ .compatible = "maxim,max7312", .data = OF_953X(16, PCA_INT), },
1165 	{ .compatible = "maxim,max7313", .data = OF_953X(16, PCA_INT), },
1166 	{ .compatible = "maxim,max7315", .data = OF_953X( 8, PCA_INT), },
1167 	{ .compatible = "maxim,max7318", .data = OF_953X(16, PCA_INT), },
1168 
1169 	{ .compatible = "ti,pca6107", .data = OF_953X( 8, PCA_INT), },
1170 	{ .compatible = "ti,pca9536", .data = OF_953X( 4, 0), },
1171 	{ .compatible = "ti,tca6408", .data = OF_953X( 8, PCA_INT), },
1172 	{ .compatible = "ti,tca6416", .data = OF_953X(16, PCA_INT), },
1173 	{ .compatible = "ti,tca6424", .data = OF_953X(24, PCA_INT), },
1174 	{ .compatible = "ti,tca9539", .data = OF_953X(16, PCA_INT), },
1175 
1176 	{ .compatible = "onnn,cat9554", .data = OF_953X( 8, PCA_INT), },
1177 	{ .compatible = "onnn,pca9654", .data = OF_953X( 8, PCA_INT), },
1178 
1179 	{ .compatible = "exar,xra1202", .data = OF_953X( 8, 0), },
1180 	{ }
1181 };
1182 
1183 MODULE_DEVICE_TABLE(of, pca953x_dt_ids);
1184 
1185 static SIMPLE_DEV_PM_OPS(pca953x_pm_ops, pca953x_suspend, pca953x_resume);
1186 
1187 static struct i2c_driver pca953x_driver = {
1188 	.driver = {
1189 		.name	= "pca953x",
1190 		.pm	= &pca953x_pm_ops,
1191 		.of_match_table = pca953x_dt_ids,
1192 		.acpi_match_table = ACPI_PTR(pca953x_acpi_ids),
1193 	},
1194 	.probe		= pca953x_probe,
1195 	.remove		= pca953x_remove,
1196 	.id_table	= pca953x_id,
1197 };
1198 
1199 static int __init pca953x_init(void)
1200 {
1201 	return i2c_add_driver(&pca953x_driver);
1202 }
1203 /* register after i2c postcore initcall and before
1204  * subsys initcalls that may rely on these GPIOs
1205  */
1206 subsys_initcall(pca953x_init);
1207 
1208 static void __exit pca953x_exit(void)
1209 {
1210 	i2c_del_driver(&pca953x_driver);
1211 }
1212 module_exit(pca953x_exit);
1213 
1214 MODULE_AUTHOR("eric miao <eric.miao@marvell.com>");
1215 MODULE_DESCRIPTION("GPIO expander driver for PCA953x");
1216 MODULE_LICENSE("GPL");
1217